Parkside PFBS 9.6 V - 2 Návod na obsluhu

PFBS 9.6 V

AKKUS MULTI CSISZOLÓGÉP

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

AKUMULATORSKI VEČNAMENSKI BRUSILNIK

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

AKU MULTI BRUSKA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

AKUMULÁTOROVÁ MULTIBRÚSKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

CORDLESS MULTI-GRINDER

Operation and Safety Notes

Translation of original operation manual

AKKU-MULTISCHLEIFMASCHINE

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

GB Operation and Safety Notes Page 5

HU Kezelési és biztonsági utalások Oldal 19

SI Navodila za upravljanje in varnostna opozorila Stran 33

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 47

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 59

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 73

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

10

8

9

D

E

F

G H

I

CB

17

16

15

13

14

19

18

22

20

21

12

11

23

5 4

17 2 36

5 GB

Table of contents

Introduction

Proper use ......................................................................................................................Page 6

Features and equipment ...............................................................................................Page 6

Included items ...............................................................................................................Page 7

Technical information ....................................................................................................Page 7

General safety advice for electrical power tools

1. Workplace safety .....................................................................................................Page 8

2.

Electrical safety .........................................................................................................Page 8

3. Personal safety ..........................................................................................................Page 8

4.

Careful handling and use of electrical power tools ................................................Page 9

5. Use and handling of the cordless electrical power tool .........................................Page 9

Safety advice for all uses .............................................................................................Page 10

Safety advice relating to kickback ...............................................................................Page 11

Special safety advice relating to grinding and disc-cutting ........................................Page 12

Further special safety advice for disc-cutting ...............................................................Page 12

Special safety advice for abrading using sandpaper ................................................Page 12

Special safety advice for polishing ..............................................................................Page 12

Special safety advice for working with wire brushes ..................................................Page 13

Safety advice applicable speciﬁcally to cordless multi-grinders ................................Page 13

Operation

Charging the battery pack ...........................................................................................Page 13

Inserting / removing the battery pack into / out of the drill / grinder .........................Page 14

Inserting or replacing a tool / collet .............................................................................Page 14

Switching on and oﬀ / Setting the speed range ..........................................................Page 14

Advice on working with materials / Tools / Speed ranges ..........................................Page 14

Tips and tricks ................................................................................................................Page 15

Maintenance and cleaning

Maintenance .................................................................................................................Page 15

Cleaning ........................................................................................................................Page 16

Service .........................................................................................................................Page 16

Warranty ................................................................................................................... Page 16

Disposal ......................................................................................................................Page 16

Manufacturer’s Declaration of

Conformity / Manufacturer

........................................................................Page 17

6 GB

Introduction

Cordless multi-grinder PFBS 9.6



Introduction

Please make sure you familiarise yourself

fully with the way the device works before

you

use it for the ﬁrst time and that you

understand how to handle electrical power tools

correctly. To help you do this please read the ac-

companying operating instructions. Keep these in-

structions in a safe place. If you pass the device on

to anyone else, please ensure that you also pass

on all the documentation.



Proper use

The cordless multi-grinder is intended to be used for

drilling, milling, engraving, polishing, cleaning,

grinding, cutting and sawing wood, metal, plastic,

ceramics or stone in dry environments. Any other

use or modiﬁcation to the drill / grinder shall be

considered as improper use and could give rise to

considerable dangers. The manufacturer will not

accept liability for loss or damage arising from

improper use. Not intended for commercial use.



Features and equipment

Cordless multi-grinder:

1

ON / OFF switch / Rotational speed control

2

Battery pack release button

The following pictograms are used in these operating instructions / on the device:

Read instruction manual!

Caution – electric shock!

Danger to life!

V

~

Volt (AC) For indoor use only!

W

Watts (Eﬀective power)

Risk of loss of life by electric shock from

damaged mains lead or mains plug!

Direct current

(Type of current and voltage)

Wear dust protection mask, protective

glasses and protective gloves.

n

0

Design no-load speed Avoid contact with rapidly rotating tools!

mA

A / Ah

Milliamps / Amps / Amp-hours Risk of ﬁre!

Safety class II Proper procedure and handling.

Observe caution and safety notes!

Do not dispose of rechargeable batteries

with your household refuse!

Risk of explosion!!

Dispose packaging and appliance in

an environmentally-friendly way!

Keep children away from electrical

power tools!

7 GB

3

Battery pack

4

Metal stirrup hanger

5

Clamping nut

6

Spigot nut

7

Spindle lock

Battery charger (see Fig. A):

8

Charging cradle

9

Mains adapter

10

LED

Accessories (see Fig. B):

11

6 HSS drills

12

2 Mandrels for mounting tools

13

3 Polishing wheels

14

4 Grinding wheels

15

1 Metal brush

16

1 Saw blade

17

10 Cutting wheels

18

5 Collets

19

2 Plastic brushes

20

2 Engraving bits

21

3 Milling bits

22

5 Grinding bits

23

Combination tool



Included items

1 Cordless multi-grinder with rechargeable

battery pack

1 Charging cradle

1 Mains adapter

1 Plastic case

1 Accessory kit (45-piece)

1 Operating instructions



Technical information

Model PFBS 9.6 - KH 3125:

Rated voltage: 9.6 V DC

No-load speed: n

0

5000 - 25000 min

-1

Max. disc ø: 25 mm

Rechargeable battery pack PFBS 9.6-2:

Rated voltage: 9.6 V DC

Capacity: 1000 mAh NI-MH

Battery charger PFBS 9.6-1:

Primary:

Rated voltage: 230 V

~

50 Hz

Rated output: 8.5 W

Secondary:

Rated voltage: 12 V DC

Charging current: 400 mA

Charging duration: approx. 3 hours

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accord-

ance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 61 dB(A)

Sound power level: 75 dB(A)

Uncertainty K: 3 dB

Evaluated acceleration, typical:

Hand / arm vibration: 2,63 m / s

2

Uncertainty K = 1,5 m / s

2

WARNING!

The vibration level given in

these instructions has been measured in accordance

with a standardised measurement procedure speciﬁed

in EN 60745 and can be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent

vibration levels and in many cases they may exceed

the values given in these instructions. It is easy to

underestimate the vibration load if the electrical pow-

er tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particular

period of working, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can result in a much lower vibration load over

the whole of the period of working.

Introduction

8 GB

General safety advice

for electrical power tools

WARNING!

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

KEEP ALL THE SAFETY ADVICE AND INSTRUC-

TIONS IN A SAFE PLACE FOR FUTURE REFER-

ENCE! THE TERM “ELECTRICAL TOOL” USED

IN THE SAFETY ADVICE REFERS TO ELECTRICAL

TOOLS POWERED BY MAINS ELECTRICITY (BY

MEANS OF A MAINS LEAD) AND ELECTRICAL

TOOLS POWERED BY RECHARGEABLE BATTER-

IES (WITHOUT A MAINS LEAD).

1.

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

b)

Do not work with the device

in potentially explosive envi-

ronments in which there

are inflammable liquids, gases or

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c)

Keep children and other

people away while you are

operating the electrical tool.

Distractions can cause you to lose control of

the device.

2.

Electrical safety

To avoid danger to

life from electric shock:

a)

The mains plug on the device must match

the mains socket. The plug must not

be modified in any way. Do not use

an adapter plug with devices fitted

with a protective earth. Unmodiﬁed

plugs and matching sockets reduce the risk of

electric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed

.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d)

Do not use the mains lead for

any purpose for which it was

not intended, e.g. to carry the

device, to hang up the device or to pull

the mains plug out of the mains socket.

Keep the mains lead away from heat,

oil, sharp edges or moving parts of the

device. Damaged or tangled mains leads

increase the risk of electric shock.

e) When working outdoors with an elec-

trical power tool always use extension

cables that are also approved for use

outdoors. The use of an extension cable suitable

for outdoor use reduces the risk of electric shock.

f) Use a residual current device (RCD)

for protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence

of drugs, alcohol or medication. One

moment of carelessness when using the device

can lead to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid unintentional operation of the

device. Check that the electrical pow-

General safety advice for electrical power tools

9 GB

er tool is switched off before you con-

nect it to the mains, pick it up or carry

it. Accidents can happen if you carry the de-

vice with your ﬁnger on the ON / OFF switch or

with the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing

and balance at all times. By doing this

you will be in a better position to control the

device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected

and

correctly used. The use of these devices

reduces the hazard presented by dust.

4.

Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

before you make any adjustments to

the device, change accessories or when

the device is put away. This precaution is

intended to prevent you from unintentionally

starting the device.

d)

When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use the device if he or she is not famil-

iar with it or has not read the instruc-

tions and advice. Electrical power tools are

dangerous when they are used by inexperienced

people.

e)

Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use the

device. Many accidents have their origins in

poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice,

and the stipulations drawn up for this

particular type of device. In doing

this, take into account the working

conditions and the task in hand. The

use of electrical power tools for purposes other

than those intended can lead to dangerous

situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

General safety advice for electrical power tools

10 GB

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d)

WARNING!

Fluids may leak out of

rechargeable battery units if they are

misused. If this happens, avoid contact

with the ﬂuid. If contact occurs, ﬂush

the aﬀected area with water. Seek

additional medical help if any of the

ﬂuid gets into your eyes. Escaping bat-

tery ﬂuid may cause skin irritation or burns.



Safety advice for all uses

General safety advice for grinding,

sanding (with sandpaper), wire brushing,

polishing and disc-cutting:

a) This electrical power tool is intended

for use as a grinding, sanding, wire-

brushing, and disc-cutting machine.

Observe all the safety advice, instructions, in-

formation in ﬁgures and all other information

you received with this device. If you do not

observe the following advice it could lead to

electric shock, ﬁre and / or serious injury.

b) Normative statement / advice for this tool is not

applicable.

c) Do not use any accessory not specifi-

cally intended by the manufacturer

for this electrical power tool. Although

an accessory may ﬁt on your electrical power

tool, this does not on its own guarantee that it

can be safely used.

d) The maximum permitted speed of an

attachment must be at least as high as

the maximum speed indicated for the

electrical power tool. An accessory rotating

faster than its permitted speed could disintegrate

or ﬂy oﬀ.

e) The external diameter and the thickness

of the attachment must be compatible

with the dimensions of your electrical

power tool. Attachments that are not dimen-

sionally compatible cannot be adequately

guarded or controlled.

f) Grinding discs, flanges, grinding

wheels or other accessories must fit

exactly on to the spindle of your elec-

trical power tool. Attachments that do not

exactly ﬁt on the spindle turn unevenly, vibrate

severely and could lead to loss of control.

g) Do not use damaged attachments.

Before every use check attachments

such as grinding discs for loose frag-

ments and cracks, grinding wheels for

cracks, deterioration or excessive

wear and wire brushes for loose or

broken wires. If the electrical power

tool or attachment is dropped, inspect

for damage or change the attachment

for an undamaged one. When you

have inspected and inserted the at-

tachment, position yourself and by-

standers away from the plane of the

rotating attachment and run the device

at maximum speed for one minute.

Damaged attachments will usually break apart

during this test.

h)

Wear personal protective

equipment. Use a full face vi-

sor, safety goggles or safety

glasses, depending on the application.

Wear a dust mask, hearing protectors,

safety gloves or special apron capable

of stopping particles of the grinding

medium or workpiece, as appropriate

for the task. Eyes must be protected from

the ﬂying debris which can arise from some

operations. Dust or breathing masks must be

capable of ﬁltering out the dust generated by

the application. Prolonged exposure to loud

noise can lead to hearing loss.

i) Keep bystanders at a safe distance

from your work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of the

workpiece or of a broken attachment could ﬂy

oﬀ and cause injury beyond the immediate

working area.

j) Hold the device by the insulated han-

dle surfaces when you are undertak-

General safety advice for electrical power tools

11 GB

ing work where there is the danger

of the attachment striking hidden

electricity cables or the device’s mains

lead. Contact with a live wire could cause

metal parts of the device to become live and

lead to electric shock.

k) Keep the mains lead away from rotat-

ing attachments. If you lose control of the

device the mains lead may become severed or

trapped and your hand or arm may be pulled

into the rotating attachment.

l) Never lay the electrical power tool

down until after the attachment has

come to a complete standstill. The rotat-

ing attachment may snag when it comes into

contact with the surface and cause you to lose

control of the device.

m) Do not have the electrical power tool

running while you are carrying it. Your

clothing could become trapped by unintention-

al contact with the rotating attachment and the

tool could be pulled into your body.

n) Clean the ventilation slots on your

electrical power tool regularly. The mo-

tor’s fan draws dust into the housing. A build-up

of metal dust could give rise to an electrical

hazard.

o)

Never use the electrical

power tool near inflammable

materials. Sparks could ignite

these materials.

p) Do not use attachments that require

the use of coolants. The use of water or

other liquid coolants could result in electric shock.



Safety advice

relating to kickback

Kickback is the sudden reaction to a pinched or

snagged rotating attachment, such as a grinding

disc, grinding pad, wire brush etc. Pinching or

snagging results in the rotating attachment coming

to an abrupt stop. This causes the electrical power

tool (if not controlled) to move in the opposite di-

rection to the direction of rotation of the attachment

at the point of constraint.

If, for example, a grinding disc is pinched or snags

in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become

trapped there and either free itself or kickback. The

grinding disc moves towards or away from the op-

erator, depending on the direction of movement of

the disc at the point of constraint. The grinding disc

could also break.

Kickback occurs as a result of incorrect use or mis-

use of the electrical power tool. It can be prevented

by taking the appropriate precautions as described

below.

a) Maintain a firm grip on the electrical

power tool and position your body

and arms to allow you to resist kick-

back forces. Always use the auxiliary

handle, if provided, to exercise the

greatest possible control over kick-

back forces or reaction torques as the

device builds up to full speed. By taking

suitable precautions the operator can control

kickback and reaction forces.

b) Do not place your hands near a rotat-

ing attachment. If kickback occurs the at-

tachment could move over your hand.

c) Avoid positioning your body in the

area into which the electrical power

tool would move in the event of a

kickback. A kickback moves the electrical

power tool in the opposite direction to the di-

rection of movement of the grinding disc at the

point of constraint.

d) Work particularly carefully in the

area of corners, sharp edges etc. to

avoid the attachment bouncing or

snagging on the workpiece. Corners,

sharp edges or bouncing have a ten-

dency to snag the rotating attachment.

This causes loss of control or kickback.

e) Do not use saw-chain woodcarving

discs or toothed discs. Such attachments

create frequent kickback and loss of control of

the electrical power tool.

General safety advice for electrical power tools

12 GB



Special safety advice relating

to grinding and disc-cutting

a) Always use the guard designed for

the type of abrasive consumable you

are using. Always use abrasive consumables

approved for use with your electrical power

tool. Abrasive consumables not approved for

use with your electrical power tool cannot be

adequately guarded and are unsafe.

b) Normative statement / advice for this tool is not

applicable.

c) Abrasive consumables must be used

only for their recommended purpos-

es, For example: never grind with the

side face of a cutting disc. Cutting discs

are intended for removing material using the

edge of the disc. Sideways forces on these

abrasive consumables can cause them to break.

d) Always use an undamaged mounting

flange of the correct size and shape

for your selected grinding disc. Suitable

ﬂanges support the grinding disc and reduce

the chance of it breaking. Flanges for cutting

discs are diﬀerent from the ﬂanges for other

abrasive discs.

e) Never use worn down abrasive con-

sumables intended for larger electrical

power tools. Abrasive consumables intended

for larger electrical power tools are not designed

for the faster rotational speeds of these smaller

electrical power tools and could break.



Further special safety

advice for disc-cutting

a) Avoid snagging the cutting disc and

do not use too much contact pressure.

Do not attempt to make excessively

deep cuts. Overloading the cutting disc in-

creases the load and the tendency of the disc

to twist or snag in the cut, making kickback or

disc breakage more likely.

b) Avoid the area in front of or behind

the rotating cutting disc. If the cutting disc

is moving away from you at the point of con-

straint in the workpiece, then, in the event of

a kickback, the electrical power tool and the

rotating disc may be thrown towards you.

c) If the cutting disc jams or you stop

work for a while, switch the device

off and hold it until the disc comes to

a complete stop. Never attempt to

pull the still rotating cutting disc out of

the cut as this could cause kickback.

Determine and rectify the reason for the jamming.

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow the

cutting disc to reach full speed before carefully

continuing with the cut. Otherwise the disc

could snag, jump out of the workpiece or

cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) Be particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are

cutting into. The cutting disc plunged into

the surface could cut through gas or water

pipes, electricity cables or other objects and

cause kickback.



Special safety advice for

abrading using sandpaper

 Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming,

tearing of the sheet or kickback.



Special safety

advice for polishing

 Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

General safety advice for electrical power tools

13 GB

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.



Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) Use a guard, if recommended, but

make sure that the wire brush does

not come into contact with the guard.

The diameters of disc brushes and cup brushes

can increase due to contact pressure and cen-

tripetal forces.

Safety advice applicable

speciﬁcally to cordless

multi-grinders

 When you use the drill / grinder wear

the following protective equipment:

safety glasses and protective gloves.

CAUTION! RISK OF INJURY! The tool

continues to rotate after it has been

switched oﬀ! Avoid contact with rap-

idly rotating drill / grinder components.



WARNING!

Securely support the work-

piece. Use clamps or a vice to grip the workpiece

ﬁrmly. This is much safer than holding it in your

hand.



WARNING!

RISK OF INJURY! Never

support yourself by placing your hands near or

in front of the device or the workpiece surface.

A slip can result in injury.



DANGER OF FIRE FROM FLYING

SPARKS! Abrading metal creates

ﬂying sparks. For this reason, always

make sure that nobody is placed in any danger

and that there are no inﬂammable materials

near the working area.



WARNING!

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

Wear a dust mask!



WARNING!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

 Do not soak the materials or the surface you

are about to work on with liquids containing

solvents.

 Avoid abrading paints containing lead or other

substances hazardous to health.

 Do not machine materials containing asbestos.

Asbestos is a known carcinogen.

 Avoid contact with moving sanding or grinding

tools.

 Do not machine moist materials or damp sur-

faces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!



WARNING!

RISK OF INJURY!

Switch the device oﬀ and allow it to come to a

standstill before you put it down.



WARNING!

Always keep the device

clean, dry and free of oil or grease.



Operation

Never use the device for a purpose for which it was

not intended or with non-original parts / accessories.

The use of tools or accessories other than those rec-

ommended in the operating instructions could lead

to you suﬀering an injury.



Charging the battery pack

NOTE! A battery pack that has been

unused for a while or never been charged

must be charged before reuse or ﬁrst use.

The battery pack requires about 3-5 cycles before

it can reach its full charge.

CAUTION! RISK OF INJURY!

Always pull

out the mains plug (

mains adapter

9

) before

General safety advice for electrical power tools / Operation

14 GB

you

insert the battery pack into or take it out of

the charger.

 Connect the adapter

9

to a mains socket.

 Insert the battery pack

3

into the charging

cradle

8

. This can only be inserted with the

correct polarity.

 The LED

10

lights up green whenever the bat-

tery pack

3

is in the charging cradle

8

and

the adapter

9

is connected to a mains socket.

CAUTION! Do not charge a battery pack for

a second time in close succession. There is a

danger of overcharging the battery pack.



Inserting / removing the

battery pack into / out of the

drill / grinder

Inserting the battery pack:

 Set the ON / OFF switch

1

to position “0”.

 Insert the battery pack

3

into the drill / grinder

until it engages.

Removing the battery pack:

 Pressing the battery pack buttons

2

at the

sides at the same time allows you to remove

the battery pack

3

.



Inserting or replacing

a tool / collet

 Press the spindle lock

7

and keep it pressed.

 Rotate the clamping nut

5

until the lock

engages.

 Loosen the clamping nut

5

with the combina-

tion key

23

.

 If a tool is already inserted, remove it.

 First insert the tool you wish to use through the

clamping nut

5

before you insert it into the

collet

18

suitable for the tool shaft.

 Press the spindle lock

7

and keep it pressed.

 Insert the collet

18

into the threaded insert and

tighten the clamping nut

5

on the thread using

the combination key

23

.

NOTE: Use the screwdriver end of the combi-

nation key

23

to release or tighten the screw of

the mandrels

12

.



Switching on and oﬀ / Setting

the speed range

Switching on / Setting the speed range:

 Set the ON / OFF switch

1

to a position

between “2” and “10”.

Switching oﬀ:

 Set the ON / OFF switch

1

to position “0”.



Advice on working with

materials / Tools / Speed ranges

 Use the highest speed when working on steel

or iron with the milling bits.

 Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

 Use the low speed range for working on plastics

and low-melting point materials.

 Use high speeds on wood.

 Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Operation

15 GB

Operation / Maintenance and cleaning



Tips and tricks

If you use press too hard you run the risk of break-

ing the tool or damaging the workpiece. You will

achieve the best results by operating the tool at a

constant rotational speed and using a low contact

pressure on the workpiece.



Maintenance and cleaning



Maintenance

 Before and after a prolonged period of

non-use fully charge the battery pack

3

.

Setting the appropriate speed

Symbols on

ON / OFF

switch

1

Material

0

(Drill / grinder switched oﬀ)

6

Softwood, metal

2

Plastics and low melting

point materials

8

Hardwood

4

Stone, Ceramics

10

Steel

Examples of appropriate tool selection Function

Function Accessory Application

Drilling

HSS drill

11

Drilling wood (see Fig. C)

Milling

Milling bits

21

Various tasks, e.g. hollowing out, gouging,

shaping, grooving or slotting

Engraving

Engraving bits

20

Markings (see Fig. D)

Polishing,

derusting

CAUTION!

Use only the lightest

contact pressure of

the tool on the work-

piece.

Metal brush

15

Derusting (see Fig. E)

Polishing wheel

13

Working on various metals and plastics, in

particular noble metals like gold or silver

(see Fig. F)

Cleaning

Plastic brush

19

E.g. cleaning complex plastic housings or the

area around a door lock

Metal brush

15

E.g. cleaning cutlery, jewellery, tools (see Fig. E)

(The metal brush is softer than steel)

Grinding

Grinding wheels

14

,

grinding bits

22

Grinding of stone, precise tasks on hard materials,

such as ceramics or alloy steel (see Fig. G)

Cutting and

sawing

Cutting discs

17

Cutting metal, plastic or wood (see Fig. H)

Saw blade

16

Saw blade Sawing steel, metal, wood or plastic

(see Fig. I)

16 GB



Cleaning

 Clean all the dirt oﬀ the drill / grinder. Use a

dry cloth for cleaning.



Service



WARNING!

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.



WARNING!

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.



Warranty

This appliance is guaranteed for 3 years

from the date of purchase. It has been care-

fully produced and meti-culously checked

before delivery. Please keep your receipt

as proof of purchase. Contact your service

centre by telephone in case of questions

pertaining to the warranty. Your goods can

be transmitted free of cost only in this man-

ner. This warranty applies only to the initial

purchaser and is non-transferable.

The warranty covers only material or manufactur-

ing faults, not normal wear or damage to fragile

parts such as switches or rechargeable batteries.

The appliance is intended solely for private, not

commercial, use.

If this product has been subjected to improper or in-

appropriate handling, abuse, or interventions not

carried out by one of our authorised sales and

service outlets, the warranty will be considered void.

This warranty does not aﬀect your statutory rights.

GB

DES UK LTD

Tel.: 0871 5000 700 (£ 0,10 / minute)

e-mail: [email protected]



Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive

2002 / 96 / EC about waste electrical and elec-

tronic equipment and its transposition into national

legislation, worn out electric tools must be collected

separately and taken for environmentally compatible

recycling.

Do not dispose of rechargeable

batteries with your household

refuse!

Faulty or used rechargeable batteries must be recy-

cled in accordance with Directive 2006 / 66 / EC.

Return the appliance with integrated rechargeable

battery via the available collection facilities.

Please contact your local council oﬃce to ﬁnd out

about disposal facilities for your worn-out electrical

tools or discarded battery packs.

Maintenance and cleaning / Service / Warranty / Disposal

17 GB



Manufacturer’s Declaration of

Conformity / Manufacturer

We, Kompernaß GmbH, the person responsible for

documents: Mr Dennis Dohm, Burgstr. 21, D-44867

Bochum, Germany, hereby declare that this product

complies with the following standards, normative

documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic compatibility

(2004 / 108 / EC)

Type / Device description:

Cordless multi-grinder

Date of manufacture (DOM): 12 - 2009

Bochum, 31.12.2009

Hans Kompernaß

- Managing Director -

We reserve the right to make technical modiﬁca-

tions in the course of further development.

Manufacturer’s Declaration of Conformity / Manufacturer

18

19 HU

Tartalomjegyzék

Bevezetés

Rendeltetésszerű használat ..........................................................................................Oldal 20

Felszerelés .....................................................................................................................Oldal 20

A szállítmány tartalma ..................................................................................................Oldal 21

Műszaki adatok ............................................................................................................Oldal 21

Elektromos szerszámokra vonatkozó általános

biztonsági tudnivalók

1. A munkahely biztonsága ..........................................................................................Oldal 22

2.

Elektromos biztonsága .............................................................................................Oldal 22

3. Személyek biztonsága .............................................................................................Oldal 22

4.

Az elektromos szerszámokkal való gondos járás és azok gondos használata ...Oldal 23

5. Az akkus szerszám alkalmazása és kezelése .........................................................Oldal 24

Biztonsági tudnivalók minden alkalmazáshoz ............................................................Oldal 24

Visszarúgás és az arra vonatkozó biztonsági tudnivalók ..........................................Oldal 25

A csiszolásra és vágásra vonatkozó sajátos biztonsági tudnivalók ..........................Oldal 26

A vágótárcsákkal való munkákra vonatkozó további biztonsági tudnivalók ............Oldal 26

Csiszolópapírral való munkákra vonatkozó sajátos biztonsági tudnivalók ...............Oldal 27

A polírozásra vonatkozó sajátos biztonsági tudnivalók .............................................Oldal 27

A drótkefével való munkákra vonatkozó sajátos biztonsági tudnivalók ....................Oldal 27

Multi csiszológépekre vonat kozó készülékspeciﬁkus biztonsági tudnivalók .............Oldal 27

Kezelés

Az akku-telep feltöltése .................................................................................................Oldal 28

Az akku-telep behelyezése / kivétele a készülékbe / -ből ...........................................Oldal 28

Szerszám / befogóhüvely behelyezése / cseréje ........................................................Oldal 28

Be- és kikapcsolás / Fordulatszám-tartomány beállítása .............................................Oldal 29

Utalások az anyagmegmunkálás- / szerszám- / Fordulatszám-tartománnyal

kapcsolatban .................................................................................................................Oldal 29

Tippek és trükkök ...........................................................................................................Oldal 30

Karbantartás és tisztítás

Karbantar tás ..................................................................................................................Oldal 30

Tisztítás ...........................................................................................................................Oldal 30

Szerviz .........................................................................................................................Oldal 30

Garancia ....................................................................................................................Oldal 30

Mentesítés ................................................................................................................Oldal 31

Konformitásnyilatkozat / Gyártó .........................................................Oldal 31

20 HU

Akkus multi csiszológép PFBS 9.6



Bevezetés

Az első üzembevétel előtt ismerkedjen meg

a készülék funkcióival és informálódjon

az elektromos szerszámokkal való helyes

járásról. Ehhez olvassa el a következő Használati

utasítást. Őrizze meg jól ezt az utasítást. A készülék

továbbadása esetén harmadiknak kézbesítse vele

együtt annak a teljes dokumentációját is.



Rendeltetésszerű használat

A Akkus multi csiszológépet fa, fém, műanyag, ke-

rámia vagy kőzetek száraz helyiségekben való fú-

rására, marására, gravírozására, polírozására, tisz-

títására, csiszolására és vágására lehet használni.

Minden más irányú használat vagy a készülék

megváltoztatása nem rendeltetésszerűnek számit

és jelentős veszélyekkel jár. A nem rendeltetésszerű

alkalmazásból eredő károkért a gyártó nem áll jót.

A készülék nem ipari használatra való.



Felszerelés

Akkus multi csiszológép:

1

BE- / KI-Kapcsoló / fordulatszámszabályzás

2

Akku-reteszeléskioldó gomb

3

Akku-telep

4

Fémkengyel

5

Szorítóanya

Bevezetés

Ebben a Használati utasításban / a készüléken a következő piktogrammokat használtuk:

Olvassa el a kezelési utasítást

Vigyázat, elektromos áramütés

veszélye! Életveszély!

V

~

Volt (Váltóáram) Csak beltéri használatra való!

W

Watt (Teljesítmény)

Sérült hálózati kábelnél vagy –dugó-

nál áramütés általi életveszély áll fenn!

Egyenáram

(áram- és feszültségfajta)

Viseljen porvédő álarcot, védőszem-

üveget és védőkesztyűt.

n

0

Névleges üresjárati fordulatszám

Kerülje el, hogy a gyorsan forgó

szerszámokhoz hozzáérjen!

mA

A / Ah

Milliamper / amper / amperóra Tűzveszély!

Védelmi osztály II Így jár el helyesen!

Vegye ﬁgyelembe a ﬁgyelmeztető és

a biztonsági utasításokat!

Ne dobja az akkukat a háztarási

szemétbe!

Robbanásveszély!

Környzetbarát módon távolítsa el a

csomagolóanyagot!

Tartsa a gyerekeket távol az elektromos

szerszámoktól!

21 HU

6

Hollandi anya

7

Tengelyrögzítés

Akku-feltöltő készülék (lásd az A ábrát):

8

Feltöltővályú hüvellyel

9

Hálózati rész

10

LED

Tartozékok (lásd a B ábrát):

11

6 HSS-fúró

12

2 Befogó tokmány a szerszámbefogáshoz

13

3 Polírozó tárcsa

14

4 csiszoló tárcsa

15

1 Fémkefe

16

1 Fűrészlap

17

10 Vágótárcsa

18

5 Befogópatron

19

2 Műanyagkefe

20

2 Metsző-bit

21

3 Maró-bit

22

5 Csiszoló-bit

23

Kombikulcs



A szállítmány tartalma

1 Akkus multi csiszológép akku-csomaggal

1 Feltöltővályú hüvellyel

1 Hálózati rész

1 Műanyagkoﬀer

1 Tartozék-készlet (45 részes)

1 Kezelési utasítás



Műszaki adatok

PFBS 9.6 - KH 3125:

Névleges feszültség: 9.6 V DC

Üresjárati

fordulatszám: n

0

5000 - 25000 min

-1

Max. tárcsa ø: 25 mm

Akku-csomag PFBS 9.6-2:

Névleges feszültség: 9.6 V DC

Kapazitás: 1000 mAh NI-MH

Akku-feltöltőegység PFBS 9.6-1:

Primér:

Névleges feszültség: 230 V

~

50 Hz

Névleges teljesítmény: 8,5 W

Sekundér:

Névleges feszültség: 12 V DC

Töltőáram: 400 mA

Töltés tartama: kb. 3 óra

Védettségi osztály: II /

Zaj- és rezgésinformációk:

A hangszint mért értékeit az EN 60745 szabvány-

nak megfelelően állapították meg. Az elektromos

szerszám A-kiemelés szerinti hangszintje tipikusan

a következő:

Hangnyomásszint: 61 dB(A)

Hangteljesítményszint: 75 dB(A)

Bizonytalansági tényező K: 3 dB

Viseljen hallásvédőt!

Értékelt gyorsulás, jellemző:

Kéz-kar-rezgé: 2,63 m / s

2

Bizonytalansági tényező K = 1,5 m / s

2

FIGYELMEZTETÉS!

Az ebben az utasítás-

ban megadott rezgésszintet egy EN 60745-ben

megszabott mérési eljárásnak megfelelően mérték

és az a készülékek összehasonlítására felhasználható.

A rezgésszint az elektromos készülék felhasználá-

sának a módjától függően változhat és az értéke

egyes esetekben az ebben az utasításban megadott

értékeket túllépheti. A rezgésterhelést alá lehet be-

csülni, ha az elektromos szerszámot rendszeresen

ilyen módon használják.

Utalás: A rezgésterhelésnek egy bizonyos munka-

időszak időtartama alatti pontos felbecsülésére

azokat az időket is ﬁgyelembe kell venni, amelyek

alatt a készülék ki van kapcsolva, vagy habár jár,

valójában nem használják. Ez a teljes munkaidő-

szak alatti rezgésterhelést jelentősen lecsökkentheti.

Bevezetés

Stránka sa načítava...

Parkside PFBS 9.6 V - 2 Návod na obsluhu

Tento návod je vhodný aj pre

Parkside PFBS 9.6 V - 2 Návod na obsluhu

v iných jazykoch

Súvisiace články

Ostatné dokumenty