Avent SCD292/31 Používateľská príručka

SCF334, SCF332

SCF334

Fig. A

SCF332

1 2 4 5

14

15

16

17

18

13

7

6

8 10 11

12

3

9

English 6

Čeština 28

Lietuviškai 50

Magyar 72

Slovensky 95

Українська 118

Contents

Introduction __________________________________________________________________________7

General description (Fig. A) ______________________________________________________________ 7

Intended use ________________________________________________________________________ 8

Important safety information ___________________________________________________________ 8

Contraindications _____________________________________________________________________ 8

Preparing for use _____________________________________________________________________ 9

Cleaning and sanitizing ________________________________________________________________ 9

Find the best cushion for you ___________________________________________________________ 11

Assembling the breast pump ___________________________________________________________ 11

Using the breast pump ________________________________________________________________ 12

When to express milk _________________________________________________________________ 12

Tips ________________________________________________________________________________ 13

Operating the breast pump _____________________________________________________________ 13

Storing breast milk ____________________________________________________________________ 14

Compatibility ________________________________________________________________________ 14

Feeding _____________________________________________________________________________ 15

For your child‘s safety and health _______________________________________________________ 15

Before rst use _______________________________________________________________________ 15

Cleaning bottles ______________________________________________________________________ 16

Assembling bottles ___________________________________________________________________ 16

Heating breast milk ___________________________________________________________________ 16

Maintenance and storage of bottles _____________________________________________________ 16

Additional information _________________________________________________________________ 16

Choosing the right teat for your baby_____________________________________________________ 17

Replacement ________________________________________________________________________ 17

Batteries ____________________________________________________________________________ 17

Recycling ___________________________________________________________________________ 17

Removing the batteries ________________________________________________________________ 18

Ordering accessories __________________________________________________________________ 18

Accessories __________________________________________________________________________ 18

Additional items ______________________________________________________________________ 18

Warranty and support _________________________________________________________________ 18

Troubleshooting ______________________________________________________________________ 19

Supplemental information ____________________________________________________________ 20

Technical information ________________________________________________________________ 20

EMC information ____________________________________________________________________ 20

Usage and storage conditions ___________________________________________________________24

Technical specications ________________________________________________________________25

Explanation of symbols _______________________________________________________________ 26

6

English

Introduction

Congratulations on your purchase and welcome to Philips Avent! To fully benet from the support

that Philips Avent oers, register your product at www.philips.com/welcome.

The Philips Avent breast pump has a unique design that enables you to sit in a more comfortable

position while expressing. The soft massage cushion* is designed to feel soft and warm and to mimic

your baby’s suckling action to provide milk ow - comfortably and gently. The breast pump starts in

a gentle mode that helps to stimulate your milk ow. You can then choose from three suction modes,

according to your own personal comfort. The pump is easy to assemble and operate and all parts that

come into contact with breast milk are dishwasher-safe.

Healthcare professionals say that breast milk is the best nutrition for babies during the rst year,

combined with solid food after the rst 6 months. Your breast milk is specially adapted to your baby’s

needs and help protect your baby against infection and allergies. A breast pump can help you to

breastfeed longer. You can express and store your milk so that your baby can still enjoy the benets,

even if you cannot be there to provide it yourself. As the pump is compact, quiet and discrete to

use, you can take it with you anywhere, allowing you to express milk at your own convenience and

maintain your milk supply.

This breast pump is for household use only.

*The cushions included with this pump were designed to comfortably t the majority of mothers.

However, if you need it, you can buy a larger cushion separately.

General description (Fig. A)

Figure A. The numbers mentioned below refer to the numbers on the gure of the front foldout

page of this user manual.

1 Motor unit with silicone tube and cap *

2 Silicone diaphragm *

3 Pump body *

4 Massage cushion *

5 Cover *

6 Battery housing (single electric breast pump only)

7 On/o button

8 Stimulation button

9 Low suction button

10 Medium suction button

11 Deep suction button

12 Adapter

13 White valve *

14 Philips Avent Natural bottle *

15 Dome cap *

16 Screw ring *

17 Nipple *

18 Sealing disc *

*Note:The twin electric breast pump comes with two pieces of the marked parts, except for the

motor unit.

SCF332 contains: single electric breast pump (including 1 bottle), breast pads

SCF334 contains: twin electric breast pump (including 2 bottles), breast pads, travel bag

7

English

Intended use

The Philips Avent Comfort Single/Twin electric breast pump is intended to express and collect milk

from the breast of a lactating woman.

The device is intended for a single user.

Important safety information

Read this user manual carefully before you use the breast pump and save it for future reference.

This user manual can also be found online via the Philips Avent website: www.philips.com/avent

Contraindications

Never use the breast pump while you are pregnant, as pumping can induce labor.

Warning

Warnings to avoid choking, strangulation and injury:

- Do not allow children or pets to play with the motor unit, the adapter or accessories.

- Children should be supervised to ensure that they do not play with the appliance.

- Always unplug the breast pump immediately after use.

- Do not leave the breast pump unattended when it is plugged in.

- This breast pump is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge. Such persons can only use

this breast pump if they are supervised by or have received proper instruction concerning use of

the appliance by a person responsible for their safety.

Warnings to avoid electric shock:

- Inspect the breast pump, including the adapter, for signs of damage before each use. Do not use

the breast pump if the adapter or plug is damaged, if it does not work properly or if it has been

dropped or submerged in water.

Warnings to prevent burns:

- Only use the adapter indicated on the appliance to prevent overheating of the adapter.

- Non-rechargable batteries are not to be recharged to prevent overheating and leaking of batteries.

Warnings to avoid poisoning and contamination and to ensure hygiene:

- For hygienic reasons, the breast pump is only intended for repeated use by a single user.

- Clean, rinse and sanitize all pump parts, except the motor unit, the tube and cap and the adapter,

before each use.

- Only store breast milk collected with a cleaned and sanitized pump.

- Do not use the breast pump if the silicone diaphragm appears to be damaged or broken.

See chapter ‘Ordering accessories’ for information on how to obtain replacement parts.

- Do not use antibacterial or abrasive cleaning agents when you clean breast pump parts.

- If you are not going use the appliance for a long period of time, remove the batteries to prevent

leaking of batteries.

8

English

Warnings to avoid breast and nipple problems and pain:

- Do not attempt to remove the pump body from your breast while under vacuum. Switch o the

appliance and break the seal between your breast and the pump funnel with your nger. Remove

the pump from your breast.

- Never use the breast pump while you are sleepy or drowsy to avoid lack of attention during use.

- Always switch o the breast pump before you remove the pump body from your breast to release

the vacuum.

- Never use any accessories or parts from other manufacturers or that Philips Avent does not

specically recommend. This could lead to improper working of the appliance and could inuence

Electromagnetic Compatibility (EMC). If you use such accessories or parts, your warranty becomes

invalid.

- Do not continue pumping for more than ve minutes at a time if you do not succeed in expressing

any milk. Try to express at another time during the day.

- If the process becomes very uncomfortable or painful, stop using the pump and consult your

breastfeeding advisor.

- If the pressure generated is uncomfortable or causes pain, switch o the appliance, break the seal

between the breast and the pump body with your nger and remove the pump from your breast.

- Never drop or insert any foreign object into any opening.

Caution

Caution to prevent damage to and malfunctioning of the product:

- Prevent the adapter and motor unit from coming into contact with water.

- Keep the adapter and the silicone tubes away from heated surfaces to avoid overheating and

deformation of these parts.

- Never put the motor unit or the adapter in water, in a dishwasher or in a sanitizer.

- Although the breast pump is compliant with applicable EMC directives, it may still be susceptible

to excessive emissions and/or may interfere with other equipment. A consequence can be that

the breast pump switches o or goes into error mode. To prevent interference, keep other electric

equipment away from the breast pump during expressing (see 'Technical information').

- There are no user serviceable parts inside the motor unit of the breast pump. No modication of

equipment is allowed. If you do, your warranty becomes invalid.

- Do not short-cut the supply terminals of the batteries.

Preparing for use

Cleaning and sanitizing

The motor unit, the silicone tube, cap and the adapter do not require cleaning and sanitizing, as they

do not come into contact with breast milk. Clean and sanitize all other parts of the breast pump

before rst use. Also clean these parts after each subsequent use and sanitize them before each

subsequent use.

Caution: Never put the motor unit or the adapter in water, in a dishwasher or in a sanitizer, as this

causes permanent damage to these parts.

9

English

Cleanable parts

Clean the following parts before (rst) use and after each subsequent use. Please check the list in the

General Description section to see which items are included with your breast pump.

Breast pump parts:

- Silicone diaphragm

- Pump body

- Massage cushion

- White valve

- Cover

Bottle parts:

- Philips Avent Natural bottle

- Dome cap

- Screw ring

- Teat

- Sealing disc

Supplies needed for cleaning:

Washing in sink Washing in dishwasher

- Mild dishwashing liquid - Mild dishwashing liquid/tablet

- High quality drinking water - High quality drinking water

- Soft brush or clean dish towel

- Clean sink or bowl

Warning: Do not use antibacterial or abrasive cleaning agents when you are cleaning.

1 Disassemble the breast pump and bottle completely. Also remove the white valve from the breast

pump.

Caution: Be careful when you remove the white valve and when you clean it. If it gets damaged,

your breast pump does not function properly. To remove the white valve, gently pull at the

ribbed tab on the side of the valve.

2 Wash the parts in the sink or dishwasher.

Washing in sink: Detach all parts and soak for 5 minutes in hot water with some mild dishwashing

liquid. Clean all parts with a soft brush or clean dish towel and then rinse them thoroughly (Fig. 2).

Washing in dishwasher: Clean the parts, except the motor unit, the silicone tube and cap and the

adapter, in the dishwasher (on the top rack only).

Note: To clean the valve, rub it gently between your ngers in warm water with some washing-up

liquid. Do not insert objects into the valve, as this may cause damage.

10

English

Disinfection (optional)

After cleaning, if you also want to disinfect, you can boil the parts in water in a household pot.

Supplies needed for disinfection:

- A household pot

- High-quality drinking water

Disinfect the parts in the following way:

Fill a household pot with enough water to cover all parts. Bring the water to boil. Place the parts in

the household pot and boil them for 5 minutes (Fig. 3). During disinfection with boiling water, prevent

the bottle or other parts from touching the side of the pan. This can cause irreversible product

deformation or damage that Philips cannot be held liable for.

Allow water to cool and gently remove the parts from the water. Place the parts neatly on a clean

paper towel or in a clean drying rack and allow them to air dry. Avoid using cloth towels to dry the

parts because they can carry germs and bacteria that are harmful to your baby.

Find the best cushion for you

Expressing breast milk should be comfortable. Therefore we oer 3 soft exible cushions: a 19.5 mm

massage cushion (supplied with your breast pump) and a 25 mm massage cushion.

For optimal comfort and performance, you should choose the optimal cushion for your nipples (Fig. 4).

19,5 mm: Massage cushion,

25 mm: Massage cushion (not included):

1 Start with the standard 19,5 mm massage cushion supplied with your breast pump. You can nd

the size of the cushion on the cushion itself (Fig. 5).

2 If the cushion is too small, purchase the larger 25 mm cushion (see ‘Ordering accessories’).

A too small cushion can cause pain or less eective expression (Fig. 6).

Assembling the breast pump

Note: Make sure you have cleaned and sanitized the appropriate parts of the breast pump.

1 Wash your hands thoroughly before you handle the cleaned parts.

Warning: Be careful, the cleaned parts may still be hot. Only start assembling the

breast pump when cleaned parts have cooled down.

Note: You may nd it easier to assemble the breast pump while it is wet.

2 Insert the white valve into the pump body from underneath. Push the valve in as far as possible

(Fig. 7).

3 Screw the pump body clockwise onto the bottle until it is securely xed (Fig. 8).

4 Insert the silicone diaphragm into the pump body from above. Make sure it ts securely around the

rim by pressing down with your ngers to ensure a perfect seal (Fig. 9).

5 Insert the cushion into the funnel-shaped section of the pump body (Fig. 10).

6 Push in the inner part of the cushion as far as possible and make sure that it is perfectly sealed all

around the rim of the pump body (Fig. 11).

11

English

7 Press in between the petals to remove any trapped air (Fig. 12).

Note: Place the cover over the cushion to keep the breast pump clean while you prepare for

expressing.

Warning: Always use the breast pump with a cushion.

8 Insert the adapter into the wall socket and insert the plug at the other end into the motor unit

(Fig. 13).

The adapter reference code is indicated on the bottom of the appliance. Only use the indicated

adapter with the appliance.

- For battery operation (single electric breast pump only), turn the bottom of the motor unit in the

direction indicated by the marks on the bottom (step 1 (Fig. 14)) and remove it (step 2 (Fig. 14)).

Insert four new 1.5V AA batteries (or 1.2V, in case of rechargeable batteries) into the battery housing.

Check the markings on the housing of the battery for the correct polarity. Reattach the bottom to

the motor unit.

Note: A new set of batteries provides 1-3 hours of operating time. Rechargeable batteries will lose

capacity over time and may cause a decrease in operating time.

Note: If you have inserted batteries in the battery housing of the motor unit and plug in the adapter,

the breast pump will run from on electrical power. The batteries cannot be charged in the unit.

Warning: Do not mix dierent type of batteries.

Warning: Do not mix used and new batteries.

9 Attach the silicone tube and cap onto the diaphragm. Push down the cap until it is securely in

place (Fig. 15).

Using the breast pump

When to express milk

If breastfeeding goes well, it is advisable (unless advised otherwise by your healthcare professional/

breastfeeding advisor) to wait until your milk supply and breastfeeding schedule are established

(normally at least 2 to 4 weeks after giving birth) before you start expressing.

Exceptions:

- If breastfeeding does not go well immediately, expressing regularly can help to establish and

maintain your milk supply.

- If you are expressing milk for your baby to be given in hospital.

- If your breasts are engorged (painful or swollen), you can express a small amount of milk before or

between feeds to ease the pain and to help your baby latch on more easily.

- If you have sore or cracked nipples, you may wish to express your milk until they are healed.

- If you are separated from your baby and wish to continue to breastfeed when you are reunited,

you should express your milk regularly to stimulate your milk supply.

You need to nd the optimum times of the day to express your milk, for example just before or after

your baby’s rst feed in the morning when your breasts are full, or after a feed if your baby has not

emptied both breasts. If you have returned to work, you may need to express during a break. Using

a breast pump requires practice and it may take several attempts before you succeed. Fortunately,

the Philips Avent electric breast pump is easy to assemble and use so you will soon get used to

expressing with it.

12

English

Tips

- Familiarize yourself with the breast pump and how to operate it before you use it for the rst time.

- Choose a time when you are not in a rush and will not be interrupted.

- A photograph of your baby can help encourage the ‘let-down’ reex.

- Warmth can also help: try to express after a bath or shower, or place a warm cloth or Philips Avent

Thermopad on the breast for a few minutes before you start expressing.

- You may nd it easier to express while your baby is feeding from the other breast, or immediately

after a feed.

- If expressing becomes painful, stop and consult your breastfeeding advisor or healthcare

professional.

Operating the breast pump

1 Wash your hands thoroughly and make sure your breasts are clean.

2 Relax in a comfortable chair (you may wish to use cushions to support your back). Make sure you

have a glass of water nearby.

3 Press the assembled pump body against your breast. Make sure that your nipple is centered,

so that the massage cushion creates an airtight seal (Fig. 16).

For twin electric breast pump users: The twin electric breast pump enables you to express milk

from both breasts at the same time. However, you can also use the appliance to express from one

breast in just the same way. Attach both assembled pump bodies to the silicone tube and cap.

We recommend to place the cover over the other one.

4 Make sure that your nipple ts correctly in the cushion. See for correct size of cushion, section

"Find the best cushion for you".

5 Press the on/o button (Fig. 17).

- The breast pump automatically starts up in stimulation mode and the on/o button and the

stimulation button light up.

- You begin to feel the suction on your breast.

6 Once your milk starts owing, you can adopt a slower rhythm by pressing the lowest suction button

(Fig. 18).

- This button lights up instead of the stimulation button.

Note: Do not worry if your milk does not ow immediately. Relax and continue pumping. The rst

few times you use the breast pump, you may need to use a higher suction mode to get your milk

owing.

7 Depending on your own personal comfort, you may wish to use a higher suction mode that

provides deeper suction. You can always return to a lower suction mode (Fig. 19). You can turn o

the breast pump whenever you like by pressing the on/o button (Fig. 20).

Note: You do not need to use all suction modes, only use the modes that are comfortable for you.

Warning: Always turn o the breast pump before you remove the pump body from

your breast to release the vacuum.

Warning: Do not continue pumping for more than 5 minutes at a time if you do not

succeed in expressing any milk. Try to express at another time during the day.

8 On average, you need to pump for 10 minutes to express 60-125ml (2-4 oz) of breast milk from

one breast. However, this is just an indication and varies from woman to woman.

Note: If you regularly express more than 125ml per session, you can purchase and use a 260ml/9

oz Philips Avent bottle to prevent overlling and spillage.

13

English

9 When you have nished expressing, turn o the breast pump (Fig. 20) and carefully remove the

pump body from your breast.

10 Unscrew the bottle from the pump body. You have multiple options:

- Insert a sanitized sealing disc into a sanitized screw ring and screw this onto the bottle (Fig. 21).

The expressed milk in the bottle is ready for storage.

- Alternatively, assemble a sanitized nipple and screw ring onto the bottle according to the

instructions (see 'Feeding'). Seal the nipple with the dome cap (Fig. 22).

11 Unplug the adapter from the wall outlet to disconnect the appliance from the electrical power.

Unplug the motor unit from the adapter. Unplug the silicone tube and cap from the silicone

diaphragm. For easy storage, wrap the silicone tube around the motor unit and clip the cap onto

the tube (Fig. 23).

12 Clean the other used parts of the breast pump according to the instructions in section ‘Cleaning

and sanitizing’.

Storing breast milk

Warning: Only store breast milk collected with a cleaned and sanitized pump to ensure

hygiene.

Breast milk can be stored in the fridge (not in the door) for up to 48 hours. Expressed milk should be

refrigerated immediately. If you store milk in the fridge to add to during the day, only add milk that

has been expressed into a sanitized bottle or storage cup. Breast milk can be stored in the freezer for

up to three months as long as it is kept in either sanitized bottles tted with a sanitized screw ring and

sealing disc or sanitized storage cups. Clearly label the bottle or storage cup with the date and time of

expression and use older breast milk rst. If you intend to feed your baby with the expressed breast

milk within 48 hours, you can store the breast milk in the fridge in an assembled Philips Avent bottle or

storage cup.

Do’s

- Always refrigerate or freeze expressed milk immediately.

- Only store milk collected with a sanitized breast pump in sanitized bottles.

Don’ts

- Never refreeze thawed breast milk.

- Never add fresh breast milk to frozen breast milk.

Compatibility

The Philips Avent electric breast pump is compatible with Philips Avent bottles in our range and

Philips Avent Storage cups. When you use other Philips Avent bottles, use the same type of nipple

that was supplied with that bottle. For details on how to assemble the nipple and general cleaning

instructions, see section 'Feeding' and section 'Cleaning'. These details can also be found on our

website, www.philips.com/support.

- Spare nipples are available separately. Make sure you use a nipple with the correct ow rate when

you feed your baby. To buy accessories or spare parts, visit www.shop.philips.com/service or go

to your Philips dealer. You can also contact the Philips Consumer Care Center in your country.

- Do not mix Philips Avent Anti-colic bottle parts and nipples with parts of the Philips Avent Natural

bottles. They may not t and could cause leakage or other issues.

- The high-quality plastic Philips Avent Natural bottle is compatible with most Philips Avent breast

pumps, spouts, sealing discs and cup tops.

14

English

Feeding

You can feed your baby with breast milk from Philips Avent bottles and storage cups.

For your child's safety and health

Warning

Warnings to prevent harm to children:

- Always use bottles and nipples with adult supervision. Do not

allow your child to play with small parts or walk/run while using

bottles or cups.

- Never use feeding nipples as a soother, to prevent choking

hazard.

- Continuous and prolonged sucking of uids will cause tooth

decay.

- Always check the temperature of the food before you feed your

baby to prevent burns.

- Throw away any part at the rst signs of damage or weakness.

- Keep all components not in use out of the reach of children.

- Do not alter the product or parts of it in any way. This may result

in unsafe functioning of the product.

Cautions to avoid damage to the product:

- Do not place in a heated oven, plastic can melt.

- Plastic material properties may be aected by disinfection and

high temperatures. This can aect the t of the dome cap.

- Do not leave a feeding nipple in direct sunlight or heat, or leave

in disinfectant for longer than recommended because this may

damage the product.

Before rst use

Before rst use, disassemble all parts, clean and optionally disinfect the bottle. Inspect the bottle

and feeding nipple before each use and pull the feeding nipple in all directions to prevent a choking

hazard. Throw away at the rst signs of damage or weakness.

15

English

Cleaning bottles

To ensure hygiene, clean the parts of the bottle mentioned in section 'Cleaning' before each use. Also

clean all parts after each subsequent use. You can optionally disinfect by following the instructions in

section 'Disinfection (optional)' .

Make sure that you wash your hands thoroughly and that the surfaces are clean before contact

with cleaned components. Excessive concentration of detergents may eventually cause plastic

components to crack. Should this occur, replace immediately. Inspect the bottle and feeding nipple

before each use and pull the feeding nipple in all directions to prevent a choking hazard. Throw away

any part at the rst signs of damage or weakness.

Assembling bottles

When you assemble the bottle, make sure you place the dome cap vertically onto the bottle so that

the nipple sits upright (Fig. 24). To remove the dome cap, place your hand over the dome cap and

your thumb in the dimple of the dome cap (Fig. 25). The nipple is easier to assemble if you wriggle it

upwards instead of pulling it up in a straight line (Fig. 26). Make sure you pull the nipple through until

its surface is level with the surface of the screw ring (Fig. 27).

Heating breast milk

If you use frozen breast milk, let it defrost completely before you heat it.

Note: In case of an emergency, you can defrost the milk in a bowl of hot water.

Heat the bottle or storage cup with defrosted or refrigerated breast milk in a bowl of hot water or in

a bottle warmer. Remove the screw ring and sealing disc from the bottle or remove the lid from the

storage cup.

Always stir or shake heated food to ensure even heat distribution and test the temperature before

serving. Take extra care when you heat up food in a microwave as heating food in a microwave oven

may produce localized high temperatures.

Note: We do not recommend heating breast milk in the microwave because when breast milk

becomes too warm, nutrients and vitamins are damaged.

Note: You can purchase and use Philips Avent bottle warmer to heat up the milk.

Maintenance and storage of bottles

Inspect the bottle and feeding nipple before each use and pull the feeding nipple in all directions to

prevent a choking hazard. Throw away at the rst signs of damage or weakness. For hygiene reasons,

we recommend replacing nipples after 3 months. Keep nipples in a dry, covered container. When not

in use, do not leave the nipples in sunlight or heat, or leave in disinfectant ('sterilizing solution') for

longer than recommended, as this may weaken the nipple. Do not place in a heated oven. Store the

bottles in a dry location.

Additional information

The Philips Avent nipples are available with dierent ow rates to help your baby with drinking.

Over time, you can change the nipple to accomodate the individual needs of your baby.

16

English

Choosing the right teat for your baby

The Philips Avent teats are available with dierent ow rates to help your baby with drinking. Over

time you can change the teat accommodating the individual needs of your baby. Philips Avent teats

are clearly numbered on the side to indicate ow rate (see image). Make sure you use a teat with the

correct ow rate when you feed your baby. Use a lower ow rate if your baby chokes, is leaking milk

or has trouble adjusting to the drinking speed. Use a higher ow rate if your baby falls asleep during

feeding, gets frustrated or when feeding takes a very long time.

Teats are available for 0m, 0m+, 1m+, 3m+, 6m+, variable ow (I/II/III) and thick feed (Y).

(0) The teat for 0m can be used from day one. Extra soft silicone teat and it is the lowest ow rate

available. Ideal for newborn and breastfed babies of all ages. The teat only has one opening for uids

and the number 0 is shown on the teat.

(1) The teat for 0m+ has an extra soft silicone teat. Ideal for newborn and breastfed babies of all ages.

The number 1 is shown on the teat.

(2) The teat for 1m+ has an extra soft silicone teat. Ideal for breastfed babies of all ages. The number 2

is shown on the teat.

(3) The teat for 3m+ has an extra soft silicone teat. For bottle fed babies at 3 months of age and up.

The number 3 is shown on the teat.

(4) The teat for 6m+ has a bite resistant silicone teat. The sturdier teat is ideal for bottle fed babies

at 6 months of age and up. The number 4 is shown on the teat.

(I/II/III) Variable ow: has a bite resistant silicone teat. The sturdier teat, with an adjustable ow rate

to babies convenience is ideal for bottle fed babies at 3 months of age and up. The teat has one slot

cut on the top for uid and the markings I, II, III on the edges of the teat.

(Y) Thick feed: has a bite resistant silicone teat. The sturdier teat, designed for thicker feeds is ideal

for bottle fed babies at 6 months of age and up. The teat has one Y cut for uid and the symbol Y

on the teat.

Note: Every baby is unique and your baby's individual needs may vary from the description of ow

rates.

Note: Teat (0) might not be available in your country, please check www.philips.com/avent.

Replacement

Batteries

When using the breast pump (single electric breast pump) on batteries, always use four 1.5 AA

batteries (or 1.2V in case of rechargeable batteries). Remove the rechargeable batteries from the motor

unit before charging them.

Remove exhausted batteries and dispose of them safely, see chapter 'Recycling'. For instructions on

how to replace the batteries, see chapter ‘Preparing for use’.

17

English

Recycling

- This symbol means that this product shall not be disposed of with normal household waste

(2012/19/EU) (Fig. 28).

- This symbol means that this product contains disposable batteries which shall not be disposed of

with normal household waste (2006/66/EC) (Fig. 29).

- Follow your country's rules for the separate collection of electrical and electronic products and

batteries. Correct disposal helps prevent negative consequences for the environment and human

health.

Removing the batteries

Follow the steps below to remove batteries from the appliance (single electric breast pump only).

1 Before removing the batteries, make sure the motor unit is turned o and the adapter is unplugged.

2 To remove the batteries, turn the bottom of the motor unit in the direction indicated by the marks

on the bottom (step 1) and remove it (step 2 (Fig. 30)).

3 Remove the four 1.5V AA batteries (or 1.2V in case of rechargeable batteries) from the battery

housing.

4 Reattach the bottom to the motor unit.

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/service or go to your Philips dealer.

You can also contact the Philips Consumer Care Center in your country (see the international warranty

leaet for contact details).

Accessories

Additional items

The following items may be included. Please check the list in the section General Description to see

which items are included with your breast pump.

- Disposable breast pads

- Cover

- Sealing discs

- Travel bag

Warranty and support

If you need information or support, please visit www.philips.com/support or read the international

warranty leaet.

18

English

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you

are unable to solve the problem with the information below, visit www.philips.com/support for a list

of frequently asked questions or contact the Consumer Care Center in your country.

Problem Solution

I experience pain when I

use the breast pump

Stop using the breast pump and consult your breastfeeding advisor. If the

pump does not come away easily from the breast, it may be necessary to

break the vacuum by placing a nger between the breast and Massage

Cushion.

The breast pump is

scratched

In case of regular use, some light scratching is normal and does not

cause problems. However, if a part of the breast pump becomes badly

scratched or cracks, stop using the breast pump and contact the Philips

Consumer Care Center or visit www.shop.philips.com/service to obtain

a replacement part. Be aware that combinations of detergents, cleaning

products, sanitizing solution, softened water and temperature uctuations

may, under certain circumstances, cause the plastic to crack. Avoid

contact with abrasive or antibacterial detergents as these can damage

the plastic.

The breast pump does

not work and the on/o

button ashes.

First check if you have assembled the breast pump correctly and make

sure that there is no kink in the tube.To prevent interference keep other

electric equipment, like mobile phone or laptop, away from the breast

pump while expressing.If you are using the single electric breast pump

with batteries, replace the batteries according to the instructions in

the user manual.If you are using the breast pump on electrical power,

check to make sure you are using the adapter that was supplied with the

product.If the problem persists, contact the Consumer Care center via

www.philips.com/support.

I do not feel any suction. Check if you have assembled the breast pump correctly by following

the steps in section 'preparing for use'. Make sure that the silicone tube

is rmly attached to the motor unit and to the cap and diaphragm.Also

make sure that the pump is positioned correctly on the breast to allow for

vacuum to occur. If you still do not feel any suction, please contact the

Consumer Care center via www.philips.com/support.

The pump has too much

suction.

Follow below guidelines if you experience too much suction with your

breast pump:

- Make sure you only use the Philips Avent comfort breast pump’s parts.

- Make sure you have assembled the comfort breast pump with the

massage cushion: not using the massage cushion can result in too much

vacuum.

- When using a breast pump for the rst time, you may experience the

suction level as too high at rst. Practicing can help. If the problem

persists, consult your breastfeeding advisor.

19

English

Supplemental information

Below some common breastfeeding-related conditions are described. If you experience any of these

symptoms, contact a healthcare professional or breastfeeding specialist.

Symptom

Pain sensation Perceived pain of breast or nipple.

Sore nipples Persistent pain in the nipples at the beginning of the pumping period, or

that lasts throughout the entire pumping period, or hurts between sessions,

much similar to the pain felt during breastfeeding.

Engorgement Swelling of the breast. The breast may feel hard, lumpy and tender.

May include erythema (redness) of the breast area and fever.

Bruise, thrombus A reddish-purple discoloration that does not blanch when pressed.

When a bruise fades, it becomes green and brown.

Blistering Looks like small bubbles on the surface of the skin.

Injured tissue on nipple

(nipple trauma)

- Fissures or cracked nipples.

- Skin tissue peeling o the nipple. Normally occurs in combination with

cracked nipples and/or blisters.

- Nipple tear.

Bleeding Cracked or teared nipples can lead to bleeding of the aected area.

Clogged mammary

ducts

A red, tender lump on the breast. May include erythema (redness) of the

breast area and fever. Can lead to Mastitis (breast inammation) if left

untreated.

Technical information

EMC information

The Philips Avent breast pump needs special precautions regarding EMC and needs to be installed

and put into service according to the EMC information provided in this section.

Portable and mobile RF communications equipment can aect the Philips Avent breast pump.

The electronic breast pump has no essential performance. Due to EMC inuences, like wireless home

network devices, mobile phones or cordless telephones, the breast pump can turn o or go into error

mode. This will not lead to unacceptable risks. To prevent interference, keep other electric equipment

at least 3.3 feet/1.0 m away from the breast pump during expressing and do not stack with other

electrical equipment. Cable length of the adapter: 2.50 meter/ 8.2 feet.

Electromagnetic Compatibility (EMC, IEC 60601-1-2)

Declaration – electromagnetic emissions

The Philips Avent breast pump is intended for use in the electromagnetic environment specied

below. The user of the Philips Avent breast pump should assure that it is used in such an environment.

20

English

Stránka sa načítava ...

Avent SCD292/31 Používateľská príručka

Táto príručka je tiež vhodná pre

Avent SCD292/31 Používateľská príručka

Súvisiace články

Ďalšie dokumenty