Husqvarna 345BT Používateľská príručka

345BT

EN Operator's manual 6-18

BG Ръководство за експлоатация 19-31

BS Korisnički priručnik 32-43

CS Návod k použití 44-55

DA Brugsanvisning 56-67

DE Bedienungsanweisung 68-80

EL Οδηγίες χρήσης 81-93

ES Manual de usuario 94-106

ET Kasutusjuhend 107-118

FI Käyttöohje 119-130

FR Manuel d'utilisation 131-142

HR Priručnik za korištenje 143-154

HU Használati utasítás 155-166

IT Manuale dell'operatore 167-179

LT Operatoriaus vadovas 180-191

LV Lietošanas pamācība 192-203

NL Gebruiksaanwĳzing 204-215

NO Bruksanvisning 216-226

PL Instrukcja obsługi 227-239

PT Manual do utilizador 240-251

RO Instrucţiuni de utilizare 252-263

RU Руководство по эксплуатации 264-276

SK Návod na obsluhu 277-288

SL Navodila za uporabo 289-300

SR Priručnik za rukovaoca 301-312

SV Bruksanvisning 313-323

TR Kullanım kılavuzu 324-334

UK Посібник користувача 335-349

ID Manual operator 350-361

AR 󰂿󰃕󰃀 󰂿󰂱󰂙󰃅󰃀 362-372

MY Operator's manual 373-385

TH คูมือการใชงาน 386-396

ES-MX Manual de usuario 397-409

PT-BR Manual do operador 410-421

BP152HV

2

14

24

29

25

23

19

21

20

22

17

6

18

15

16

5

4

11

3

10

7

12

8

28

26

9

6

27

13

1

30

1

2 3 4 5 6 7

8 9 10 11 12 13

14 15 16 17

18 19

20

B

D

A

C

21

E

22 23

24 25

26

A

B

27

28 29

30 31

0

32 33

34 35

36 37

38 39

40 41

B

C

A

42

Contents

Introduction.....................................................................6

Safety..............................................................................7

Assembly........................................................................ 9

Operation......................................................................10

Maintenance................................................................. 12

Troubleshooting............................................................14

Transportation and storage...........................................15

Technical data.............................................................. 16

EC Declaration of Conformity....................................... 17

Introduction

Product description

This product is a backpack blower with a fuel engine.

We have a policy of continuous product development

and therefore reserve the right to modify the design and

appearance of products without prior notice.

Intended use

Use the product to blow leaves and other unwanted

material from areas such as lawns, pathways and

asphalt roads.

Product overview

(Fig. 1)

1. Throttle control lever

2. Frame

3. Harness

4. Engine cover

5. Fan cover

6. Air intake screen

7. Air filter

8. Starter rope handle

9. Fuel tank

10. Waist belt

11. Spark plug

12. Vibration damping system

13. Choke control

14. Control handle

15. Stop switch with throttle control

16. Throttle trigger

17. Pipe angle

18. Clamp

19. Flexible hose

20. Control pipe

21. Cable clamp

22. Intermediate pipe

23. Blower nozzle

24. Operator's manual

25. Combination wrench

26. Air purge bulb

27. High speed nozzle

28. Idle adjustment screw

29. Fan

30. Foot plate

Symbols on the product

(Fig. 2) WARNING! This product can be

dangerous and cause serious injury or

death to the operator or others. Be careful

and use the product correctly.

(Fig. 3) Read the operator's manual carefully

and make sure that you understand the

instructions before use.

(Fig. 4) Use approved hearing protection and

approved eye protection. If the

environment contains dust, use a

breathing mask.

(Fig. 5) Use approved protective gloves during

operation and maintenance. Use

protective boots or shoes with non-slip

soles. Use clothing of strong fabric and of

full length.

(Fig. 6) Make sure that long hair is put above your

shoulders.

(Fig. 7) Do not wear jewelry or loose clothing

during operation.

(Fig. 8) Mixture of gasoline and two-stroke oil.

(Fig. 9) Air purge bulb.

(Fig. 10) Keep all body parts away from hot

surfaces.

(Fig. 11) Do not go near the impeller as it turns.

61854 - 002 - 29.03.2022

(Fig. 12) Choke, open position.

(Fig. 13) Choke, closed position.

(Fig. 14) Idle adjustment screw.

(Fig. 15) This product complies with applicable EC

Directives.

(Fig. 16) This product conforms to the applicable

UK regulations.

(Fig. 17) Noise emissions to the environment

according to European Directive

2000/14/EC and New South Wales

legislation “Protection of the Environment

Operations (Noise Control) Regulation

2017”. Noise emission data can be found

on the machine label and in the Technical

data chapter.

(Fig. 18)

Look out for thrown ob-

jects. Thrown objects can

cause serious injury. Use

personal protective equip-

ment.

(Fig. 19)

Keep a safety distance at

a minimum of 15 m to per-

sons or animals.

yyyywwxxxxx

The rating plate or the la-

ser printing shows the seri-

al number. yyyy is the pro-

duction year and ww is the

production week.

Note: Other symbols/decals on the product refer to

certification requirements for other commercial areas.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

The definitions below give the level of severity for each

signal word.

WARNING: Injury to persons.

CAUTION: Damage to the product.

Note: This information makes the product easier to

use.

General safety instructions

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not do changes to the product without approval

from the manufacturer and always use original

accessories. Modifications and/or accessories that

are not approved can result in serious injury or the

death of the operator or others.

• Do not use a damaged product. Do the safety

checks and maintenance given in this operator's

manual. All other maintenance must be done by

approved servicing personnel.

• All servicing and repair operations must be done by

approved servicing personnel. If a part of the product

is defective, speak to your servicing dealer.

Vibration safety

This product is for occasional operation only.

Continuous or regular operation of the product can

cause “white finger” or equivalent medical problems

from vibrations. Examine the condition of your hands

and fingers if you operate the product continuously or

regularly. If your hands or fingers have discoloration,

have pain, tingle, or are numb, stop work and speak to a

physician immediately.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use the

product.

• This product can be dangerous and cause serious

injury or death to the operator or others. Be careful

and use the product correctly.

• Do an inspection of the product before use. Refer to

Maintenance on page 12

.

1854 - 002 - 29.03.2022 7

• Do not operate the product when you are tired, ill or

under the influence of alcohol or other drugs that can

decrease your vision, judgment or coordination.

• Install all covers and guards before use. To prevent

electrical shock, make sure that the spark plug cap

and ignition cable are not damaged.

• Do not touch the spark plug or ignition cable when

the engine is on.

• Keep a safety distance at a minimum of 15 m to

persons or animals. If persons, children or animals

come nearer than 15 m, stop the product. Point the

product away from persons, animals, open windows

and other objects.

• Do not let children operate the product. Make sure

that all operators read and understand the contents

of this operator's manual.

• Keep hands or other objects away from the blower

housing during operation. Rotating parts can cause

serious injury.

• Do not use the product if the air intake screen is

not installed. Always make sure that the air intake

screen is installed and not damaged before use.

• If an emergency occurs, release the waist belt and

chest belt of the harness and let the product fall.

• Obey national regulations and directives.

• Keep all body parts away from hot surfaces.

• Too much vibration can cause damage to the

circulation or the nervous system. Speak to your

physician if you have symptoms, for example

numbness, loss of feeling, tingling, pricking, pain,

loss of strength or changes in skin color in your

fingers, hands or wrists.

• Look out for thrown objects. Thrown objects can

cause serious injury.

• Do not use the product in bad weather, for example

fog, rain, strong winds and too cold environments.

To do work in bad weather can cause tiredness and

dangerous conditions.

• Make sure that you can move and keep a stable

position. Do a check of the work area for possible

obstacles, for example rocks. Be careful if you

operate the product on a slope.

• Do not put the product on the ground with the engine

on.

• Do not operate the product from high positions, for

example on a ladder.

• Make sure that you can always be heard if an

accident occurs.

• Make sure that the exhaust fume outlet is not

blocked. To prevent damage to the product, keep

obstacles at a minimum distance of 50 cm from the

exhaust fume outlet.

• Do not start the product indoors, in bad airflow or

near flammable material. The engine exhaust fumes

contain carbon monoxide, which can cause carbon

monoxide poisoning. The engine exhaust fumes are

hot and can contain sparks which can start a fire.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use the

product.

• Use approved personal protective equipment when

you use the product. Personal protective equipment

cannot fully prevent injury but it can decrease the

degree of injury. Speak to your dealer for more

information.

• Use approved hearing protection. Long-term

exposure to noise can result in permanent hearing

damage.

• Use approved eye protection. If you use a visor,

you must also use approved protective goggles.

Approved protective goggles must agree with the

ANSI Z87.1 standard in the USA or EN 166 in EU

countries.

• Use protective gloves during operation and

maintenance.

• Use protective boots or shoes with non-slip soles.

• Use clothing of strong fabric and of full length. Do

not use jewelry or open shoes. To decrease the

risk on injury, your clothing must be close-fitting but

not limit your movements. Put your hair above your

shoulders to prevent that your hair enters rotating

parts or catches on branches.

• Use breathing protection when there is a risk of dust.

• Keep first aid equipment near.

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. Refer to

Maintenance on page 12

.

• If the safety devices are defective, speak to your

Husqvarna servicing dealer.

To do a check of the muffler

WARNING: Do not use a product with

a defective muffler.

WARNING: The muffler becomes very

hot during and after operation, also at idle

speed. Use protective gloves to prevent burn

injuries.

WARNING: The inner side of the

muffler contains chemicals that may be

81854 - 002 - 29.03.2022

carcinogenic. Do not touch the muffler if it

is damaged.

• Regularly do a visual check of the muffler. The

muffler keeps noise levels to a minimum and sends

exhaust fumes away from the operator. Refer to

To

examine and clean the cooling system on page 13

.

To do a check of the vibration damping system

1. Make sure that there are no cracks or deformation

on the vibration damping units.

2. Make sure that the vibration damping units are

correctly attached to the engine unit and handle unit.

Refer to

Product overview on page 6

for information

about where the vibration damping system is on your

product.

To do a check of the start/stop switch

1. Use the start/stop switch to stop the engine.

2. Make sure that the engine stops fully.

To see where the start/stop switch is on your product,

refer to

Product overview on page 6

.

Harness safety

Always use the harness when you operate the product.

If you do not use the harness, you cannot operate the

product safely. This can result in injury to you or other

persons. Make sure that the waist belt and chest strap

are attached and correctly adjusted. There is a risk that

an open belt can go into the fan of the product.

(Fig. 20)

Fuel safety

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not mix or add the fuel indoors or near a heat

source.

• Do not start the product if there is fuel or oil on the

product or on your body.

• Do not start the product if the engine has a fuel leak.

Examine the engine for fuel leaks regularly.

• Always be careful with fuel. Fuel is flammable and

the fuel fumes are explosive and can cause serious

injury or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put the product or a fuel container near warm

objects, an open flame, a spark or a pilot light.

• Always use approved containers for storage and

transportation of fuel.

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you use the

product.

• Stop the engine, remove the spark plug and let

the engine become cool before maintenance and

assembly.

• A blocked spark arrestor screen causes the engine

to become too hot which causes damage to the

engine.

• If the spark arrestor screen is frequently blocked,

it can be a sign that performance of the catalytic

converter is decreased. Speak to your servicing

dealer to examine the muffler.

Assembly

Introduction

WARNING: Read and understand the

safety chapter before you assemble the

product.

To assemble the blower pipe and the

control handle on the product

Note: Lubricate the tubes and flexible hose to make

them easier to assemble.

1. Attach the flexible hose (A) to the pipe angle and the

control pipe (B) with the clamps (C) and (D). (Fig.

21)

2. Attach the handle holder (E) to the control pipe. Align

the handle holder with the flange on the control pipe.

(Fig. 22)

3. Adjust the position of the control handle to a safe

and correct work position. Tighten the knob.

4. Attach the cable to the flexible hose with the cable

clamp. (Fig. 23)

5. Attach the intermediate pipe to the control pipe. (Fig.

24)

6. Attach the blower nozzle to the intermediate pipe.

1854 - 002 - 29.03.2022 9

Note: The blower nozzle can only be installed on

the intermediate pipe.

7. For higher air speed, attach the high speed nozzle to

the blower nozzle.

Operation

Introduction

WARNING: Read and understand the

safety chapter before you use the product.

Fuel

This product has a two-stroke engine.

CAUTION: Incorrect type of fuel can

result in engine damage. Use a mixture of

gasoline and two-stroke oil.

Premixed fuel

• Use Husqvarna premixed alkylate fuel for best

performance and extension of the engine life. This

fuel contains less harmful chemicals compared

to regular fuel, which decreases harmful exhaust

fumes. The quantity of remains after combustion is

lower with this fuel, which keeps the components of

the engine more clean.

To mix fuel

Gasoline

• Use good quality unleaded gasoline with a maximum

of 10% ethanol contents.

CAUTION: Do not use gasoline with

an octane grade less than 90 RON/87

AKI. Use of a lower octane grade can

cause engine knocking, which causes

engine damages.

Two-stroke oil

• For best results and performance use Husqvarna

two-stroke oil.

• If Husqvarna two-stroke oil is not available, use a

two-stroke oil of good quality for air-cooled engines.

Speak to your servicing dealer to select the correct

oil.

CAUTION: Do not use two-stroke

oil for water-cooled outboard engines,

also referred to as outboard oil. Do not

use oil for four-stroke engines.

To mix gasoline and two-stroke oil

Gasoline, liter Two-stroke oil,

liter

2% (50:1)

5 0.10

10 0.20

15 0.30

20 0.40

CAUTION: Small errors can influence

the ratio of the mixture drastically when you

mix small quantities of fuel. Measure the

quantity of oil carefully and make sure that

you get the correct mixture.

(Fig. 25)

1. Fill half the quantity of gasoline in a clean container

for fuel.

2. Add the full quantity of oil.

3. Shake the fuel mixture.

4. Add the remaining quantity of gasoline to the

container.

5. Carefully shake the fuel mixture.

CAUTION: Do not mix fuel for more

than 1 month at a time.

To fill the fuel tank

WARNING: Obey the procedure that

follows for your safety.

1. Stop the engine and let the engine become cool.

2. Clean the area around the fuel tank cap. (Fig. 26)

3. Shake the container and make sure that the fuel is

fully mixed.

4. Remove the fuel tank cap slowly to release the

pressure.

5. Fill the fuel tank.

10 1854 - 002 - 29.03.2022

CAUTION: Make sure that there is

not too much fuel in the fuel tank. The

fuel expands when it becomes hot.

6. Tighten the fuel tank cap carefully.

7. Clean fuel spillage on and around the product.

8. Move the product 3 m/10 ft or more away from the

refueling area and fuel source before you start the

engine.

Note: To see where the fuel tank is on your product,

refer to

Product overview on page 6

.

To start a cold engine

WARNING: Air is released as soon as

the engine is started, even when it idles. Do

not let anyone stand close to the blower or

the blower tube.

1. If the engine is cold, put the choke control (A) to

the closed choke position. Refer to

Symbols on the

product on page 6

. (Fig. 27)

2. Push the air purge bulb (B) again and again for a

minimum of 10 times and fuel starts to fill the air

purge bulb. It is not necessary to fill the air purge

bulb fully.

3. Put the throttle control in the fast idle position. Align

the guide marks on the throttle control lever and the

control handle. (Fig. 28)

4. Put the product on a flat surface on the ground.

5. Hold the product with the left hand and put your foot

on the foot plate. (Fig. 29)

6. Pull the starter rope handle slowly with the right hand

until resistance occurs.

Note: Do not pull the starter rope handle to full

extension and do not let go of the starter rope

handle.

7. Pull the starter rope handle quickly with the right

hand until the engine starts or attempts to start,

maximum 6 times. If the engine starts, move the

choke lever gradually to the open position and

continue to step 11. If the engine does not start,

continue to step 9.

8. When the engine attempts to start, move the choke

lever gradually to the open position.

9. Pull the starter rope handle quickly with the right

hand until the engine starts, maximum 6 times.

Note: If the engine does not start,

repeat the starting instructions from step

1.

10. Let the engine run for 30 seconds.

11. Put the throttle control at idle speed. (Fig. 30)

12. Push the throttle trigger to adjust the blower speed.

Refer to

To use the throttle trigger on page 11

.

To start a warm engine

• If the ambient temperature is below 32°C / 90°F,

use the same starting procedure as

To start a cold

engine on page 11

but do not put the choke control

in the closed choke position.

• If the ambient temperature is above 32°C / 90°F,

use the same starting procedure as

To start a cold

engine on page 11

.

To use the throttle trigger

• To increase the blower speed during operation, push

the throttle trigger until you get the correct speed.

(Fig. 31)

• To decrease the blower speed during operation,

release the throttle trigger until you get the correct

speed.

To start the engine when the fuel is too

hot

If the product does not start, the fuel can be too hot.

Note: Always use new fuel and decrease the

operation time during warm weather.

1. Put the product in a cool area away from open

sunlight.

2. Let the product cool down for 20 minutes at

minimum.

3. Press the air purge bulb again and again for 10-15

seconds.

4. Obey the procedure to start a cold engine. Refer to

To start a cold engine on page 11

.

To operate the product

• Operate the product at usual work hours. Obey local

regulations.

• Decrease the pieces of equipment and select the

correct speed for your task. Use the throttle at lowest

position possible to prevent more noise and dust

than necessary.

• Keep the blower nozzle near the ground.

Note: Husqvarna recommends that you use the

full blower nozzle extension.

• Make a note of the wind direction and operate the

product in the direction of the wind.

• Use applicable garden tools to release material from

the ground.

• In areas with dust, use spray equipment to wet the

area. This decreases the operation time.

• After operation, keep the product in storage

vertically.

1854 - 002 - 29.03.2022 11

To stop the product

CAUTION: Do not stop the product at

full speed.

1. Push the stop switch. (Fig. 32)

Note: When the product stops, you can hear a

knock sound. This is typical and is not an indication

of a defective product.

To adjust the harness

1. Put on the harness of the product.

2. Put the waist belt around your waist and connect the

belt buckle for the waist strap. (Fig. 33)

3. Tighten the waist belt strap. (Fig. 34)

4. Connect the belt buckle for the chest strap. (Fig. 35)

5. Adjust the position of the chest strap. (Fig. 36)

6. Tighten the chest strap. (Fig. 37)

7. Tighten the shoulder straps until the product is tight

against your body. (Fig. 38)

8. Tighten the load lifter straps. (Fig. 39)

Maintenance

Introduction

WARNING: Read and understand the

safety chapter before you do maintenance

on the product.

Maintenance schedule

Maintenance Daily Weekly Monthly

Clean the external surfaces. X

Make sure that the control handle operates correctly. X

Make sure that the start/stop switch operates correctly. Refer to

To do a check of

the start/stop switch on page 9

.X

Examine the engine, the fuel tank and the fuel lines for leaks. Examine the fuel

filter for contamination. Replace the fuel filter if it is necessary. X

Clean the air filter. Replace the air filter if it is necessary. X

Tighten nuts and screws. X

Examine the air intake and make sure that it is not blocked. X

Examine the starter and the starter rope for damages. X

Examine the vibration damping units for damages, cracks and deformation.

Make sure that the vibration damping units are correctly installed. X

Examine the spark plug. Refer to

To do a check of the spark plug on page 13

. X

Clean the cooling system. X

Clean the external surface of the carburetor and the area around it. X

Clean the fuel tank. X

Examine all cables and connections. X

Examine and clean the spark arrestor screen on the muffler (for products without

catalytic converter). X

12 1854 - 002 - 29.03.2022

Maintenance Daily Weekly Monthly

Examine and clean the spark arrestor screen on the muffler (for products with

catalytic converter). X

Examine the spark plug. Replace if it is necessary. X

To adjust the idle speed

1. Make sure that the air filter is clean and that the air

filter cover is attached.

2. Adjust the idle speed with the idle speed screw. To

see where the idle speed screw is on your product,

refer to

Product overview on page 6

.

To do a check of the spark plug

CAUTION: Use the recommended

spark plug. Refer to

Technical data on page

16

. An incorrect spark plug can cause

damage to the product.

1. Stop the engine and let the product become cool.

2. Clean the spark plug if it is dirty.

3. Make sure that the electrode gap is correct. Refer to

Technical data on page 16

. (Fig. 40)

4. Replace the spark plug monthly or more frequently if

it is necessary.

To do maintenance on the muffler

CAUTION: If the spark arrestor screen

is frequently blocked, it can be a sign that

performance of the catalytic converter is

decreased. Speak to you servicing dealer

to examine the muffler. A blocked spark

arrestor screen causes overheating and

results in damage to the cylinder and piston.

CAUTION: The spark arrestor screen

must be replaced if it is damaged. Do not

use a product if the spark arrestor screen on

the muffler is missing or defective.

• Clean the spark arrestor screen on the muffler. Use

a wire brush. (Fig. 41)

• Let a servicing dealer replace or do service on the

muffler and the spark arrestor screen after 50 hours

of operation.

To examine and clean the cooling

system

The cooling system includes the cooling fins on the

cylinder and the air intake screen.

1. Stop the engine.

2. Make sure that the cooling system is not dirty or

blocked. If it is necessary, clean the air intake screen

and cooling fins.

CAUTION: A dirty or blocked

cooling system can increase the

temperature of the engine and cause

damage to the product. A clogged air

intake screen decreases the blow force.

3. Examine the cooling system for damages. Make

sure that the parts are attached correctly to the

product.

To clean the air filter

CAUTION: Do not use a product

without an air filter or with a damaged air

filter. Dust in the air can cause damage to

the engine.

1. Push the choke control to the closed position.

2. Remove the air filter cover (A).

3. Remove the pre-filter (B) from the air filter cover.

(Fig. 42)

4. Remove the air filter (C) from the filter frame.

5. Clean the pre-filter and the air filter with warm water

and soap.

Note: An air filter that has been used for a long

time cannot be fully cleaned. Replace the air filter

regularly and always replace a defective air filter.

6. Clean the inner surface of the air filter cover (A) with

a brush.

7. Put the air filter in the filter frame.

8. Attach the pre-filter to the air filter cover.

9. Attach the air filter cover to the product.

1854 - 002 - 29.03.2022 13

Troubleshooting

The engine is not possible to start

Check Possible cause Solution

Starter pawls. Blocked or

worn starter

pawls.

Adjust or replace the starter pawl/s.

Clean around the starter pawl/s.

Speak to an approved servicing dealer.

Fuel tank. Incorrect fuel

type. Drain the fuel tank and use correct fuel.

Carburetor. Adjustment of

the idle speed. Adjust the idle speed with the idle adjustment screw.

Spark (no

spark). Spark plug is

dirty or wet. Make sure that the spark plug is dry and clean.

Electrode gap

on the spark

plug is incor-

rect.

Clean the spark plug. Make sure that the electrode gap is correct.

Refer to technical data for the correct electrode gap.

Spark plug.

Spark plug is

loose. Tighten the spark plug.

There is un-

wanted materi-

al on the spark

plug electro-

des.

Make sure that the fuel mixture is correct.

Make sure that the air filter is clean.

Engine starts but stops again

Check Possible cause Solution

Fuel tank. Incorrect fuel

type. Drain the fuel tank and use the correct fuel.

Carburetor. Engine will not

operate cor-

rectly at idle

speed.

Speak to your servicing dealer.

Air filter. Clogged air fil-

ter. Clean the air filter.

14 1854 - 002 - 29.03.2022

Transportation and storage

WARNING: To prevent the risk of fire,

make sure that there are no leaks or fumes

during transportation or storage. Make sure

that there is no risk of sparks or fire.

• Empty the fuel tank before transportation or long-

term storage. Push the air purge bulb to make

sure that all fuel is removed. Discard the fuel at an

applicable disposal location.

• Make sure that the product is clean and that a full

servicing is done before long-term storage.

• Remove the spark plug and put approximately 15 ml

of two-stroke oil into the cylinder. Turn the product 3

times and install the spark plug again.

• Attach the product safely to the vehicle during

transportation.

• Keep the product in a dry, cool and clean space with

good airflow. Keep the product away from children.

1854 - 002 - 29.03.2022 15

Technical data

Husqvarna 345BT (BP152HV)

Engine

Cylinder displacement, cm351.7

Idle speed, rpm 2800

Catalytic converter Yes

Ignition system

Spark plug NGK BPMR7A/Champion RCJ6Y

Electrode gap, mm 0.6–0.7

Spark plug torque, Nm 25–30

Fuel and lubrication system

Fuel tank capacity, l/cm31.0/1000

Weight

Weight without fuel, kg 10.0

Noise emissions 1

Sound power level, measured dB (A) 110

Sound power level, guaranteed LWA dB (A) 113

Sound levels 2

Equivalent sound pressure level at the operator’s ear, measured according to EN15503 dB(A):

Equipped with blower nozzle (original) 101

Vibration levels 3

Equivalent vibration levels (ahv,eq) at handles, measured according to EN

15503, m/s26.1

Fan performance

Max. air velocity with high speed nozzle, m/s 98.3

Air flow without high speed nozzle, m3/min 13.9

1Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive

2000/14/EC. Reported sound power level for the machine has been measured with the original cutting

attachment that gives the highest level. The difference between guaranteed and measured sound power

is that the guaranteed sound power also includes dispersion in the measurement result and the variations

between different machines of the same model according to Directive 2000/14/EC.

2Reported data for noise pressure level has a typical statistical dispersion (standard deviation) of 3.0 dB (A).

3Reported data for vibration level has a typical statistical dispersion (standard deviation) of 1.5 m/s2.

16 1854 - 002 - 29.03.2022

EC Declaration of Conformity

EC declaration of conformity

We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN,

declare under our sole responsibility that the

represented product:

Description Gasoline Blower / Blower-

vaccum

Brand Husqvarna

Platform / Type / Model Platform BP152HV, repre-

senting model 345BT.

Batch Serial number dating 2022

and onwards.

complies fully with the following EU directives and

regulations:

Directive/Regulation Description

2006/42/EC “relating to machinery”

2014/30/EU “relating to electromagnet-

ic compatibility”

2000/14/EC “relating to outdoor noise”

2011/65/EU “restriction of use of cer-

tain hazardous substan-

ces”

Harmonized standards and/or technical specifications

applied are as follows: EN ISO 12100:2010, EN

15503:2009+A2, CISPR 12:2007, EN ISO 14982:2009,

EN IEC 63000:2018, EN IEC 63000:2018

In accordance with directive 2000/14/EC, Annex V, the

declared sound values are stated in the technical data

section of this manual.

TÜV Rheinland has carried out a voluntary examination

on behalf of Husqvarna AB, providing AM 50391742

- Certificate of conformity to EC Council directive

2006/42/EC for machinery.

The certificate is applicable to all manufacturing

locations and Countries of Origin, as stated on the

product.

The supplied gasoline blower / blower-vacuum conforms

to the example that underwent examination.

On behalf of Husqvarna AB, SE-561 82 Huskvarna,

SWEDEN,

Pär Martinsson

Responsible for technical documentation

1854 - 002 - 29.03.2022 17

UK declaration of conformity

We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN,

declare under our sole responsibility that the product:

Description Gasoline Blower / Blower-

vaccum

Brand Husqvarna

Platform / Type / Model Platform BP152HV, repre-

senting model 345BT.

Batch Serial number dating 2022

and onwards.

complies fully with the following UK directives and

regulations:

Directive/Regulation Description

2008/1597 The Supply of Machinery

(Safety) Regulations 2008

2016/1091 Electromagnetic Compati-

bility Regulations 2016

2001/1701 The Noise Emission in the

Environment by Equip-

ment for use Outdoors

Regulations 2001

2012/3032 The restriction of the

use of Certain Hazardous

Substances in Electrical

and Electronic Equipment

2012

Harmonized standards and/or technical specifications

applied are as follows: EN ISO 12100:2010, EN

15503:2009+A2, CISPR 12:2007, EN ISO 14982:2009,

EN IEC 63000:2018, EN IEC 63000:2018

In accordance with statutory instrument 2001/1701,

conformity assessment procedure, schedule 9, the

declared sound values are stated in the technical data

section of this manual.

The supplied gasoline blower / blower-vacuum conforms

to the example that underwent examination.

On behalf of Husqvarna AB, SE-561 82 Huskvarna,

SWEDEN,

John Thompson

Responsible for technical documentation

UK Importer:

Husqvarna UK Ltd

Preston Road, Co. Durham

DL5 6UP

18 1854 - 002 - 29.03.2022

Съдържание

Въведение................................................................... 19

Безопасност.................................................................20

Монтаж.........................................................................23

Операция.....................................................................23

Поддръжка...................................................................26

Отстраняване на проблеми........................................28

Транспорт и съхранение............................................ 29

Технически характеристики....................................... 30

Декларация за съответствие на ЕО.......................... 31

Въведение

Описание на продукта

Този продукт е преносимо компресорно оборудване

с двигател с вътрешно горене.

Ние имаме политика на непрекъснато

усъвършенстване на продуктите и затова си

запазваме правото да променяме тяхната

конструкция и външен вид без предизвестие.

Предназначение

Използвайте продукта за събиране на листа или

други нежелани предмети от зони като морави,

пътеки и асфалтирани пътища.

Общ преглед на продукта

(Фиг. 1)

1. Лост за управление на регулатора на дроселната

клапа

2. Рамка

3. Самар

4. Капак на електродвигателя

5. Капак на вентилатора

6. Филтър на смукателния въздухопровод

7. Въздушен филтър

8. Дръжка на въжето на стартера

9. Резервоар за гориво

10. Колан

11. Запалителна свещ

12. Антивибрационна система

13. Смукач

14. Ръкохватка за управление

15. Превключвател за спиране с регулатор на

дроселната клапа

16. Регулатор за газта

17. Тръбно коляно

18. Скоба

19. Мека връзка

20. Основна тръба

21. Скоба на кабел

22. Междинна тръба

23. Дюза за компресорно оборудване

24. Инструкция за експлоатация

25. Комбиниран гаечен ключ

26. Купол на горивната помпа

27. Високоскоростен накрайник

28. Регулиращ винт за обороти на празен ход

29. Вентилатор

30. Опора за крака

Символи върху машината

(Фиг. 2) ПРЕДУПРЕЖДЕНИЕ! Този продукт

може да бъде опасен и да причини

сериозно нараняване или смърт на

оператора или други хора. Внимавайте

и използвайте продукта правилно.

(Фиг. 3) Прочетете внимателно ръководството

за оператора и се уверете, че

разбирате инструкциите, преди да

използвате машината.

(Фиг. 4) Използвайте одобрени антифони и

защитни средства за очите. Ако в

околната среда има прах, използвайте

предпазна маска.

(Фиг. 5) Използвайте одобрени защитни

ръкавици по време на работа и

техническо обслужване. Използвайте

защитни ботуши или обувки с

противоплъзгащи подметки. Носете

дрехи от здрав плат и с дълги ръкави/

крачоли.

(Фиг. 6) Уверете се, че дългата коса е вдигната

над раменете.

(Фиг. 7) Не носете бижута или широки дрехи по

време на работа.

(Фиг. 8) Смес от бензин и масло за двутактов

двигател.

1854 - 002 - 29.03.2022 19

(Фиг. 9) Купол на горивната помпа.

(Фиг. 10) Дръжте всички части на тялото си

далеч от горещите повърхности.

(Фиг. 11) Не се приближавайте до ротора, когато

работи.

(Фиг. 12) Смукач, отворено положение.

(Фиг. 13) Смукач, затворено положение.

(Фиг. 14) Регулиращ винт за обороти на празен

ход.

(Фиг. 15) Този продукт отговаря на изискванията

на приложимите директиви на EO.

(Фиг. 16) Този продукт съответства на

приложимите регламенти на

Обединеното кралство.

(Фиг. 17) Шумови емисии към околната

среда съгласно Европейска директива

2000/14/ЕО и законодателството на Нов

Южен Уелс "Регламент 2017 относно

защитата от дейности, оказващи

влияние на околната среда (контрол

на шума)". Данните за шумови емисии

могат да бъдат намерени на етикета

на машината и в главата „Технически

характеристики“.

(Фиг. 18)

Внимавайте за хвърчащи

предмети. Хвърчащите

предмети могат да при-

чинят сериозно наранява-

не. Използвайте лични

предпазни средства.

(Фиг. 19)

Поддържайте минимално

безопасно разстояние 15

m от хора и животни.

ггггссxxxxx

На типовата табелка или

с лазерен печат е из-

писан серийният номер.

yyyy е годината на произ-

водство, а ww – седмица-

та на производство.

Забележка: Останалите символи/лепенки върху

продукта се отнасят до изисквания по отношение на

сертификати за други търговски зони.

Отговорност за продукта

Както е посочено в законите за отговорност за

вреди, причинени от стоки, ние не носим отговорност

за щети, причинени от нашия продукт, ако:

• продуктът е неправилно ремонтиран.

• продуктът е ремонтиран с части, които не

са от производителя или не са одобрени от

производителя.

• продуктът има принадлежност, която не е

от производителя или не е одобрена от

производителя.

• продуктът не е ремонтиран в одобрен сервизен

център или от одобрен орган.

Безопасност

Дефиниции за безопасност

Дефинициите по-долу предоставят нивото на

сериозност за всяка една предупредителна дума.

ПРЕДУПРЕЖДЕНИЕ:

Нараняване на лица.

ВНИМАНИЕ: Повреда на продукта.

Забележка: Тази информация прави продукта

по-лесен за използване.

Общи инструкции за безопасност

ПРЕДУПРЕЖДЕНИЕ: Прочетете

следващите предупредителни указания,

преди да използвате продукта.

• Не правете изменения по продукта без

одобрението на производителя и винаги

използвайте оригинални принадлежности.

Изменения и/или принадлежности, които не

са одобрени, могат да доведат до сериозно

нараняване или до смърт на оператора или други

хора.

• Не използвайте повреден продукт. Извършете

посочените в тази инструкция за експлоатация

проверки за безопасност и техническо

20 1854 - 002 - 29.03.2022

Stránka sa načítava ...

Husqvarna 345BT Používateľská príručka

Husqvarna 345BT Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty