Brooks QMBC2 / QMBM2 / QMBC3 / QMBM3 / QMBC4 / QMBM4 Návod na používanie

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Brooks

®

Quantim Low Flow Coriolis

Precision Mass Flow Measurement and

"Quantim Coriolis mass ow controllers

enable precision measurement and control with

maximum exibility and lowest overall cost of ownership."

NEMA1 / IP40

General Purpose

Conguration

NEMA 4X / IP66

Weather Proof

Conguration

IP66XP

Explosion Proof

Conguration

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

ESD (Electrostatic Discharge)

CAUTION: This instrument contains electronic components that are susceptible to damage by static electricity. Proper handling procedures must be observed

during the removal, installation or other handling of internal circuit boards or devices.

Handling Procedure:

1. Power to unit must be removed.

2. Personnel must be grounded, via a wrist strap or other safe, suitable means before any printed circuit card or other internal device is installed,

removed or adjusted.

3. Printed circuit cards must be transported in a conductive container. Boards must not be removed from protective enclosure until immediately before

installation. Removed boards must immediately be placed in protective container for transport, storage or return to factory.

Comments

This instrument is not unique in its content of ESD (electrostatic discharge) sensitive components. Most modern electronic designs contain components

that utilize metal oxide technology (NMOS, SMOS, etc.). Experience has proven that even small amounts of static electricity can damage or destroy these

devices. Damaged components, even though they appear to function properly, exhibit early failure.

Brooks Instrument designs, manufactures and tests its products to meet many national and international standards. These products must be properly

installed, operated and maintained to ensure they continue to operate within their normal specifications. The following instructions must be adhered to

and integrated into your safety program when installing, operating and maintaining Brooks Instrument products.

•To ensure proper performance, use qualified personnel to install, operate, update, program and maintain the product.

•Read all instructions prior to installing, operating and servicing the product. If this instruction manual is not the correct manual, please see back cover

for local sales office contact information. Save this instruction manual for future reference.

WARNING: Do not operate this instrument in excess of the specifications listed in the Instruction and Operation Manual. Failure to heed

this warning can result in serious personal injury and / or damage to the equipment.

• If you do not understand any of the instructions, contact your Brooks Instrument representative for clarification.

• Follow all warnings, cautions and instructions marked on and supplied with the product.

WARNING: Prior to installation ensure this instrument has the required approval ratings to meet local and national codes. Failure to heed this warning can

result in serious personal injury and / or damage to the equipment.

• Install your equipment as specified in the installation instructions of the appropriate instruction manual and per applicable local and national codes.

Connect all products to the proper electrical and pressure sources.

• Operation: (1) Slowly initiate flow into the system. Open process valves slowly to avoid flow surges. (2) Check for leaks around the flow meter inlet

and outlet connections. If no leaks are present, bring the system up to the operating pressure.

• Please make sure that the process line pressure is removed prior to service. When replacement parts are required, ensure that qualified people use

replacement parts specified by Brooks Instrument. Unauthorized parts and procedures can affect the product's performance and place the safe

operation of your process at risk. Look-alike substitutions may result in fire, electrical hazards or improper operation.

• Ensure that all equipment doors are closed and protective covers are in place to prevent electrical shock and personal injury, except when

maintenance is being performed by qualified persons.

WARNING: For liquid flow devices, if the inlet and outlet valves adjacent to the devices are to be closed for any reason, the devices must be completely

drained. Failure to do so may result in thermal expansion of the liquid that can rupture the device and may cause personal injury.

All pressure equipment with an internal pressure greater than 0.5 bar (g) and a size larger than 25mm or 1" (inch) falls under the Pressure Equipment Directive (PED).

• The Specifications Section of this manual contains instructions related to the PED directive.

• Products described in this manual are in compliance with EN directive 2014/34/EU.

• All Brooks Instrument Flowmeters fall under fluid group 1.

• Products larger than 25mm or 1" (inch) are in compliance with PED category I, II or III.

• Products of 25mm or 1" (inch) or smaller are Sound Engineering Practice (SEP).

The Brooks Instrument (electric/electronic) equipment bearing the CE mark has been successfully tested to the regulations of the Electro Magnetic

Compatibility (EMC directive 2014/30/EU).

Special attention however is required when selecting the signal cable to be used with CE marked equipment.

Quality of the signal cable, cable glands and connectors:

Brooks Instrument supplies high quality cable(s) which meets the specifications for CE certification.

If you provide your own signal cable you should use a cable which is overall completely screened with a 100% shield.

“D” or “Circular” type connectors used should be shielded with a metal shield. If applicable, metal cable glands must be used providing cable screen clamping.

The cable screen should be connected to the metal shell or gland and shielded at both ends over 360 Degrees.

The shield should be terminated to an earth ground.

Card Edge Connectors are standard non-metallic. The cables used must be screened with 100% shield to comply with CE certification.

The shield should be terminated to an earth ground.

For pin configuration : Please refer to the enclosed Instruction Manual.

European Pressure Equipment Directive (PED)

European Electromagnetic Compatibility (EMC)

Essential Instructions

Read before proceeding!

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Dear Customer,

We appreciate this opportunity to service your ow measurement and control requirements with a Brooks

Instrument device. Every day, ow customers all over the world turn to Brooks products for solutions to their gas

and liquid low-ow applications. Brooks provides an array of ow measurement and control products for various

industries from biopharmaceuticals, oil and gas, fuel cell research and chemicals, to medical devices, analytical

instrumentation, semiconductor manufacturing, and more.

The Brooks product you have just received is of the highest quality available, offering superior performance,

reliability and value to the user. It is designed with the ever changing process conditions, accuracy requirements

and hostile process environments in mind to provide you with a lifetime of dependable service.

We recommend that you read this manual in its entirety. Should you require any additional information concerning

Brooks products and services, please contact your local Brooks Sales and Service Ofce listed on the back cover

of this manual or visit www.BrooksInstrument.com

Yours sincerely,

Brooks Instrument

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

3a

2a

Quick Start Instructions IP40 - For Liquid Service

1a

QS-1

3b

2b

1b

Horizontal Mounting Vertical Mounting

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

3

2

Quick Start Instructions IP40 - For Gas Service

1

QS-2

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

QS-3

Quick Start Instructions IP66

4

5

1

2

3

When wiring terminal block in IP66 device, ensure wires are

appropriate length and are properly dressed. Unnecessarily long

wires can protrude below the top housing and cause damage to the

sensor assembly below.

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

QS-4

Quick Start Instructions IP66XP

1

4

2

3

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

QS-5

Refer to the X-Qm-HART Installation and Operation Manuals for complete wiring of a Brooks Quantim for HART interface.

HART Communications is provided on the Primary Output of the Brooks Quantim device. Connecting a HART Communicator,

or any HART modem, requires a connection between pins 4 and 1 as shown below. This connection can be anywhere on the

current loop.

Proper wiring of a Brooks Quantim NEMA 4X / IP66

Quick Start Instructions for Connecting HART on 4-20 mAmp I/O

®

DB15 Connector

Proper wiring of a Brooks Quantim NEMA 1 / IP40

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

QS-6

Proper wiring of a Brooks Quantim Explosion Proof NEMA 4X / IP66XP

PIN 5

PIN 3

14-27 Vdc Power Source

D-Connector

PIN 5

100 mA Max.

Relay

PIN 11

PIN 3

D-Connector

10 K

TTL

Quick Start Instructions for Connecting Alarm Output

Alarm Output Option 1 - Relay Alarm Output Option 2 - TTL

DB15 Connector

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

QS-7

THIS PAGE WAS

INTENTIONALLY

LEFT BLANK

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Section Page

Number Number

Quick Start Instructions

Quick Start Instructions IP40 - For Liquid Service ............................................................ QS-1

Quick Start Instructions IP40 - For Gas Service ............................................................... QS-2

Quick Start Instructions IP66 ............................................................................................ QS-3

Quick Start Instructions IP66XP ....................................................................................... QS-4

Quick Start Instructions for Connecting HART on 4-20 mAmp I/O ................................... QS-5

Section 1 Introduction

1-1 How to Use This Manual ..................................................................................................... 1-1

1-2 Description .......................................................................................................................... 1-1

1-3 Performance Specications................................................................................................. 1-2

1-4 Dimensions........................................................................................................................ 1-10

Section 2 Installation

2-1 General........................................................................................................................... 2-1

2-2 Receipt of Equipment ..................................................................................................... 2-1

2-3 Recommended Storage Practice ................................................................................... 2-1

2-4 Return Shipment ............................................................................................................ 2-1

2-5 Transit Precautions......................................................................................................... 2-2

2-6 Fluid Connections........................................................................................................... 2-2

2-7 Mechanical Installation ................................................................................................... 2-2

2-8 Process Mounting........................................................................................................... 2-4

2-9 Electrical Interfacing ....................................................................................................... 2-6

2-10 Interconnection with Peripheral Equipment .................................................................... 2-9

Section 3 Operation

3-1 Operating Procedure .......................................................................................................3-1

3-2 Zero Adjustment ..............................................................................................................3-2

3-3 Calibration Procedure......................................................................................................3-4

Section 4 Maintenance & Troubleshooting

4-1 General............................................................................................................................4-1

4-2 Troubleshooting ...............................................................................................................4-2

4-3 External Valve Service ....................................................................................................4-7

Section A Essential Instructions

A-1 Essential Instructions ......................................................................................................A-1

Warranty, Local Sales/Service Contact Information.......................................................Back Cover

i

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Figures

Figure Page

Number Number

1-1 Dimension Drawing QmB IP40 Downported ..................................................... 1-10

1-2 Dimension Drawing QmB IP40.............................................................................1-11

1-3 D-Connector Electrical Pin Connections ..............................................................1-11

1-4 Lay-In Dimensions Integral and Remote Valves ..................................................1-11

1-5 Dimensional Drawing QmB IP40 with Remote Valve .......................................... 1-12

1-6 Dimensional Drawing QmB IP66 ......................................................................... 1-12

1-7 Dimensional Drawing QmB IP66XP .................................................................... 1-13

2-1 Flow Direction Through the Quantim, as Indicated by the Arrow Engraved

on the Meter/Controller Body..................................................................................2-4

2-2 Horizontal Inverted Installation ...............................................................................2-4

2-3 Horizontal Right Side Up Installation ......................................................................2-5

2-4 Vertical Flow Up Installation ...................................................................................2-5

2-5 Proper Wiring of a Brooks QmB NEMA 4X / IP66XP .............................................2-8

2-6 Alarm Output Wiring Options ..................................................................................2-8

2-7 Wire Color Codes for 'D' Connector Assembly .....................................................2-10

3-1 Location of LED ......................................................................................................3-1

3-2 Location of the Zero Button .................................................................................... 3-2

4-1 Bench Troubleshooting Circuit ............................................................................... 4-6

4-2 Parts List ................................................................................................................ 4-8

4-3 Exploded Diagram of Valve Assembly .................................................................... 4-9

4-4 Valve Torque Pattern .............................................................................................. 4-9

Tables

Table Page

Number Number

2-1 Electrical Interfacing for Quantim ............................................................................ 2-7

4-1 Troubleshooting ........................................................................................................ 4-3

ii

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

1-1 How to Use This Manual

It is recommended to read this manual before installing, operating or

troubleshooting your Quantim

®

Mass Flow Meter/Controller.

This manual is organized into the following sections:

Section 1. Introduction

Section 2. Installation

Section 3. Operation

Section 4. Maintenance & Troubleshooting

Section A Essential Instructions

Back Cover Warranty, Local Sales/Service Contact Information

The Quality System at Brooks Instrument conforms to the quality standards

set forth in ISO 9001.

This instruction manual is intended to provide the user with all the information

necessary to install, operate and maintain the Brooks Quantim Mass Flow

Meters and Controllers.

1-2 Description

Brooks Quantim Mass Flow Meters are used to provide accurate

measurements of uid ow, uid density and temperature. The heart of these

systems is the Coriolis mass ow sensor, which produces an electrical output

signal directly proportional to mass ow rate and density. Brooks Quantim

Mass Flow Controllers couple the Coriolis sensor with

a control valve. Dependant on the application, this can be fully integrated

within the product or remote but close-coupled. The Brooks Quantim

additionally possesses digital signal processing (DSP) electronics and PID

control electronics to provide measurement and control in one complete

package.

The Quantim device is available for a wide range of gas and liquid ows.

(See specications, Section 1-3 for details).

1-1

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

1-3 Performance Specications

Performance Specications:

Flow:

Liquid Flow Specications, English Units

(9)

Gas Flow Specications

Flow rates that produce approximately 14.5 psig (1bar) pressure drop on air at 70

o

F (21

o

C)

with an inlet pressure of 500 psi (35 bar)

Liquid Flow Specications, Metric Units

(9)

Maximum

Flow Rate

(2)

Nominal Flow

Rate

(2)

Minimum Full

Scale

Minimum

Measurable

Flow

Kg/hr or l/hr Kg/hr or l/hr Kg/hr or l/hr Kg/hr or l/hr

2 0.30 0.15 0.01 0.001

QMBC 3 1.00 0.78 0.10 0.010

4 15.94 7.97 1.00 0.100

2 0.38 0.19 0.01 0.001

QMBM 3 1.00 1.00 0.10 0.010

4 27.00 13.50 1.00 0.100

Product

Type

QUANTIM

Model

(1)

QUANTIM

Tube Size

Controller

Meter

Minimum

Measurable

Flow

lb/hr gal/hr lb/hr gal/hr lb/hr

2 0.66 0.08 0.33 0.04 0.002

QMBC 3 2.21 0.26 1.72 0.21 0.022

4 35.15 4.21 17.57 2.11 0.221

2 0.84 0.10 0.42 0.05 0.002

QMBM 3 2.21 0.26 2.21 0.26 0.022

4 59.54 7.13 29.77 3.57 0.221

Maximum Flow Rate

(2)

Nominal Flow rate

(2)

Product

Type

QUANTIM

Model

(1)

QUANTIM

Tube Size

Controller

Meter

lb/hr Kg/hr

scfh

(3)

sccm

(3)

ml/min

(5)

2 0.168 0.076 2.227 1051 975.2

QMBC 3 0.472 0.214 6.261 2955 2743

4 3.960 1.796 52.52 24787 23009

2 0.227 0.103 3.034 1432 1329

QMBM 3 0.893 0.405 11.86 5595 5193

4 8.467 3.840 112.6 53116 49319

Nominal Volume Flow Rate

Nominal Mass Flow Rate

Controller

Meter

Product

Type

QUANTIM

Model

(1)

QUANTIM

Tube Size

1-2

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

100

1,000

10,000

100,000

50 100 200 500 1000 1500

Flow rate (sccm)

Inlet Pressure (psig)

Size 2 Controller

Size 3 Controller

Size 4 Controller

Size 2 Meter

Size 3 Meter

Size 4 Meter

Accuracy

(6)

+ measurement accuracy % of rate or [(zero stability/owrate) x 100] % of rate, which ever is greater

Measurement Accuracy

Zero Stabilities

Standard Measurement Accuracy vs Flow Rate Chart, Tube Size 2

Gas Flow Limits

Air, 70

o

F (21

o

C), 14.5 psi (1 bar) pressure drop

Sensor Tube

Material

Steel

Hastelloy

Fluid Type

Standard Flow

Measurement

Accuracy (% of rate)

Optional Flow

Measurement

Accuracy (% of rate)

Liquid

Gas

Liquid

Gas

0.2%

0.5%

1.0%

Sensor Tube

Material

Stainless Steel

Hastelloy

Tube Size

Zero Stability

(Kg/hr)

Zero Stability

(Lb/hr)

2

3

4

2

3

4

0.00013

0.0010

0.0040

0.0002

0.0015

0.00120

0.0003

0.0022

0.0088

0.0004

0.0033

0.0265

1-3

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Repeatability

(7)

:

± 0.05% or ± [0.5 x (zero stability/owrate) x 100]% of rate whichever is greater

Device Leak Integrity

(8)

:

Elastomer Sealed Device: Outboard 1 x 10

-9

atm. cc/sec., helium (maximum)

Metal Sealed Device: 1 x 10

-10

atm. cc/sec., helium (maximum)

Turn Down:

Controller: 100:1 or down to the minimum measurable ow, whichever ow rate is greater

Meter: to minimum measurable ow

Settling Time:

Controller (Stainless Steel sensor tube): Less than 2 seconds within 2 % full scale of nal

value, ± [(zero stability/ owrate) x 100]% of rate per SEMI Guideline E17-91

Controller (Hastelloy sensor tube): Less than 12 seconds within 2 % full scale of nal

value per SEMI Guideline E17-91

Meter: Less than 0.5 seconds within 2 % full scale of nal value, ± [(zero stability/owrate)

x 100]% of rate per SEMI Guideline E17-91

Maximum Operating Pressure

(8)

:

Standard: 3.5 MPa, 35 bar or 500 psi

Optional: 10 MPa, 100 bar or 1500 psi

Optional: 30 MPa, 300 bar or 4500 psi (Hastelloy sensor tube only)

0.1

1.0

10.0

100.0

10 100 1,000 10,000 100,000

Pressure Drop (psi)

Mass Flow (grams/hr)

Tube Size 3

Tube Size 4

Tube Size 2

Differential Pressures , Meter

(9)

Pressure Drop Liquid - (H

2

0)

Differential Pressure Requirements, Controller

(9)

:

Quantim

Model

QMBC

Quantim

Tube Size

Liquid Gas

min max*

KpA bar psi KpA bar psi

2

3

4

69

1034

1379

0.7

min min min min minmax* max* max* max* max*

250

150

1034

172410.3

13.8

10

150

200

17.2

10.3

10

*Actual maximum pressure drop will depend on process conditions and orifice selection.

(1)

1-4

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

0.1

1.0

10.0

100.0

100 1,000 10,000 100,000

Pressure Drop (psi)

Mass Flow (sccm)

Tube Size 2

Tube Size 3

Tube Size 4

Pressure Drop Air @ 500 psi Inlet Pressure

Density

(10)

:

Range: 0.2 to 2.0 grams/cc

Accuracy: ±0.005 grams/cc

Repeatability: ±0.002 grams/cc

Temperature

(11)

Device Temperature Range: 0 to 65°C or 32 to 149°F

Accuracy: ± 0.5°C or ± 1.0°F

Notes

(1)

QMBC - Brooks Quantim controller with integral control valve. QMBM - Brooks Quantim meter (no valve).

(2)

The nominal ow rate at which water at reference conditions causes approximately 1 bar of pressure drop

or the laminar to turbulent transition ow whichever is lower. Maximum ow rate is twice nominal ow rate or the

laminar to turbulent transition ow whichever is lower.

(3)

Standard volumetric conditions are 14.696 psia and 70°F.

(4)

Actual volumetric ow is a function of the mass ow and density measurements; Therefore, the accuracy of the

actual volumetric ow is a function of the mass ow and density accuracy.

(5)

ml

n

/min Reference Conditions 0

o

C at 1013.25 mbar.

(6)

Accuracy includes combined repeatability, linearity, and hysteresis. Specications are based on reference test

conditions of water/nitrogen at 68 to 77°F (20 to 25°C) and 15 to 30 psig (1 to 2 bar).

(7)

Repeatability- The maximum difference between output readings when the same input is applied consecutively;

the closeness of agreement among consecutive measurements of an output for the same value of input under

the same operating conditions, approaching from the same direction.

(8)

Helium leak and pressure test of elastomer sealed devices is performed with integral 5/16" -24 UNF connection.

(9)

Differential pressures are based on reference conditions of water and air at 68 to 77°F (20 to 25°C).

(10)

For applications with uid density in the range from 0.3 to 0.5 grams/cc the device may be sensitive to 50Hz or

60Hz vibration. The density measurement at temperatures other than 21° C (70° F) has an additional error of

approximately 0.0005 grams/cc per deg C. The density output signal is available below 0.2grams/sec. The

density accuracy is applicable over the stated density range.

1-5

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Physical Specications

Materials of Construction: Process Wetted: 316L, 316L VAR, High Alloy Ferritic Stainless

and 17-7PH

Optional: Nickel Alloy C-22 sensor tube.

Process Seals:

Elastomer Seal: Viton

®

uoroelastomers, Buna, Kalrez

®

or EPDM

Metal Seal: Stainless Steel and Nickel

Housing:

IP40: Polyurethane painted Aluminum

IP66: Polyurethane painted Aluminum

IP66XP: Aluminum

Inlet Filter: Tube Size 2 Controller: 1 micron or 10 micron inlet lter recommended

Tube Size 3 or 4: 10, 20, 30 & 40 micron lters available

Weight: Housing: IP40: 1.6 kg or 3.5 Lbs.

Housing: IP66: 1.9 kg or 4.2 Lbs.

Housing: IP66XP: 24 kg or 52 Lbs.

Moisture Content: Purged to exhaust dew point less than -40°C (-40°F) prior to shipment

to remove calibration liquid, to prevent process contamination.

Then vacuum bagged at ambient room conditions.

Process Fitting Options: 1/16", 1/8", 1/4" or 6mm tube compression, VCR, VCO or NPT(F), 3.2

mm UPG, Down Port ANSI/ISA 76.00.02 (See Model Code).

Electrical Connections: IP40: 15 pin D-Type connector. (See Figure 3).

IP66: Unpluggable Terminal Block 28-16 Awg.

IP66XP: ¾" NPT wiring access to IP40 Device with 15 pin D-Type

connector.

Dimensions: See Figures 1-1 through 1-7

Functional Specications

Output Signals

(13)

: • 4-20 mA or 0-5 Vdc active outputs represent mass ow or volume

ow

(4)

.

• And simultaneously available 4-20 mA or 0-5 Vdc active output,

represents on-line density or temperature information.

• Alarm output, max. voltage 30 Vdc, max. current 100 mA

Input Signals

(13)

: • Command (setpoint) that drives the control valve, either 4-20 mA or

0-5 Vdc input signals.

• Valve Override Function:

Left oating/unconnected - instrument controls ow at setpoint

Connected to signal at or above 5.0 Volts -valve is forced open

Connected to signal at or below 0.0 Volts -valve is forced closed

1-6

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Signal Specications: Pin 4 4-20 mA output < 500 ohm series resistance

Pin 2 0-5 Vdc output > 1K ohm load

Pin 13 4-20 mA output < 500 ohm series resistance

0-5 Vdc output > 1K ohm load

Pin 7 4-20 mA input 250 ohm input impedence

0-5 Vdc input 200 ohm input impedence

Pin 12 Valve override input > 50K ohm input impedence

Pin 3 Alarm output 100 mA maximum current sink

Power Requirements:

Voltage: +14 to 27 Vdc

(12)

.

Nominal Current: Controller: 300 mA to 400 mA

Meter: 100 mA to 150 mA

Maximum Current: Controller: 715 mA @ 14 Vdc

Meter: 470 mA @ 14 Vdc

Maximum Power: Controller: 10.0 W

Meter: 6.6 W

Additional Functions and Outputs

Damping: Factory set time constant from 0 to 10 seconds.

Alarms and Warnings: Alarms accessed via HART or the Brooks Service Tool can be congured

to monitor the following variables

(13)

:

• Mass Flow

• Density

• Volumetric Flow

• Temperature

• Slug Flow

• Diagnostic Failure

• Setpoint Deviation

• Valve Drive

LED's

(14)

: 'STAT'

solid green: system operative.

solid red: system fault.

'AL'

ashing green: warning

ashing red: alarm

Pushbutton

(15)

:

'ZERO' setting pushbutton.

Notes (continued)

(11)

The device temperature is affected by the ambient and process temperature as well as internal warming when

the device is powered. The device should be maintained in the specied temperature range at all times.

A temperature rise of up to 20

o

C (68

o

F) from internal heating can occur in an open environment where

ambient temperature is 23

o

C (73

o

F).

(12)

Ensure the minimum required voltage and current is available at the mass owdevice taking into consderation

any losses in the interconnecting cable.

(13)

If the Quantim is congured for HART

®

communication protocol, only 4-20 mA I/O option is available.

(14)

IP66 and IP66XP Series external housing cover must be removed to gain access to status LED's.

(15)

IP66XP series external housing cover must be removed to gain access to zero push button.

1-7

Installation and Operation Manual

X-CM-QmB-eng

Part Number: 541B029AAG

July, 2018

QmB Series IP40, IP66, IP66XP

Certications and Approvals

IP40 Series

Non Incendive/ Non Sparking

United States and Canada- UL Recognized E73889, Vol. 3, Sect. 3.

Non Incendive , Class I, Division 2, Groups A, B, C and D; T4

Per UL 1604, UL 508 and CSA 22.2 No. 213 1987; C22.2 No. 14-M91

Ex nC IIC T4

Per CSA E79-15

Class I, Zone 2, AEx nC IIC T4

Per ANSI/UL 60079-15

Ambient Temperature: 0

o

C to 65

o

C

Enclosure: Type 1/ IP40

Europe - KEMA 04ATEX1241 X

II 3 G EEx nA II T4

Per EN 60079-15: 2003

Ambient Temperature: 0

o

C to 65

o

C

Enclosure: IP40

The modules shall be installed in a suitable enclosure providing a degree of at least IP54

according to EN60529, taking into account the environmental conditions under which the

equipment will be used.

IP66 Series

Non Incendive/ Non Sparking

United States and Canada- UL Recognized E73889, Vol. 1, Sect. 26. (conduit entry)

United States and Canada Recognized, UL E73889, Vol. 3, Sect. 3. (cable gland entry)

Non Incendive , Class I, Division 2, Groups A, B, C and D;

Dust Ignition Proof, Class II, Division 2, Groups F and G; Suitable for Class III, Division 2; T4

Per UL 1604, UL 508 and CSA 22.2 N0. 213 1987; C22.2 No. 14-M91

Ex nC IIC T4

Per CSA E79-15

Class I, Zone 2, AEx nC IIC T4

Per ANSI/UL 60079-15

Ambient Temperature: 0

o

C to 65

o

C

Enclosure: Type 4X/ IP66

Europe - KEMA 05ATEX1068 X

II 3 G Ex nA II T4 and II 3 D Ex tD A22 IP66 T 85 °C

Per EN 60079-0:2006, EN 60079-15:2005, EN 61241-0:2006, EN 61241-1:2004

IECEx KEM 08 0037 X

Ex nA II T4 and Ex tD A22 IP66 T85 °C

Per IEC 60079-0:2004, IEC 60079-15:2005, IEC 61241-0:2004, IEC 61241-1:2004

Ambient Temperature: 0

o

C to 65

o

C, Enclosure: IP66

*The equipment shall be installed in such a way that the risk of mechanical damage is low.

1-8

Stránka sa načítava...

Brooks QMBC2 / QMBM2 / QMBC3 / QMBM3 / QMBC4 / QMBM4 Návod na používanie

Tento návod je vhodný aj pre

Brooks QMBC2 / QMBM2 / QMBC3 / QMBM3 / QMBC4 / QMBM4 Návod na používanie

v iných jazykoch

Súvisiace články

Ostatné dokumenty