Introduction ................................................................................................... Page 4
Proper use ..................................................................................................... Page 4
Pack contents ................................................................................................ Page 4
Features ........................................................................................................ Page 4
Technical data................................................................................................ Page 5
Safety instructions ......................................................................................... Page 5
Initial operation .............................................................................................. Page 8
Power supply ................................................................................................. Page 9
Installation ..................................................................................................... Page 10
Operation ....................................................................................................... Page 10
Function test .................................................................................................. Page 11
Fault indicator ................................................................................................ Page 11
Troubleshooting ............................................................................................. Page 12
Maintenance and cleaning ............................................................................. Page 13
Disposal......................................................................................................... Page 13
Warranty ........................................................................................................ Page 13
Service .......................................................................................................... Page 14
Declaration of conformity ............................................................................... Page 14
Gas alarm GA 617
IMPORTANT INFORMATION FOLLOWING AN
ALARM
If the alarm indicates a gas leak or you can smell gas:
g DANGER OF EXPLOSION!
• Extinguish all open ames, embers and burning tobacco ! h
• Do not under any circumstances switch electrical devices on or off !c
• Do not disconnect any electric plugs (including that of the alarm unit)!
• Warn any persons at risk in the danger zone.
• Shut off the gas supply at the gas tap.
• Air all affected rooms.
• Deal with the cause with a qualied/authorized expert.
(Please display this page in a visible position next to the gas alarm)
#
GB 2
Replace after 5 years use.
Installation date :
Gas alarm
Operation and Safety Notes
Plynový alarm / alarm Plynu
Pokyny pro obsluhu a bezpečnostní pokyny
Plynový alarm
Pokyny pre obsluhu a bezpečnostné pokyny
L 94b
GAS A LARM
Ga 617
B
KOE217_GA617_Cover_LB4B.indd 1-3 19.09.2007 12:37:36 Uhr
15-30cm
max. 6m
max. 4m
15-30cm
C
R E
Q W
T
A
{ P
O
U
I
B
Introduction
Please read these operating instructions thor-
oughly and carefully. They are part of this
product and contain important instructions
relating to its operation and handling. Please
always observe all safety instructions. Before
initial operation, please check that all parts are
fitted correctly. If you have any questions or
are unsure about handling of the device,
please contact the dealer or the service office.
Please keep these instructions in a safe place
and pass them on to anyone else intending to
use the device.
Proper use
The gas alarm indicates a leakage of methane,
propane or butane gas from appliances, lines,
etc. with a high-frequency tone and a flashing
red ALARM LED
c
. It is intended for use in
dry areas inside buildings, vehicles, caravans
and boats. The power supply is either by way
of the supplied 12 V DC mains adapter con-
nected to the 230 V ~ 50 Hz mains electricity
or by connection to the 12 V DC on-board
power supply system of a car, caravan or boat.
The device is for private use only. Any other
use or modification of the device constitutes
improper use and poses a serious risk of acci-
dent. The manufacturer is not liable for dam-
age caused by improper use or incorrect oper-
ation of the device. Before initial operation,
please read all operating instructions carefully
and refer to the page showing the illustrations.
Keep these operating instructions in a safe
place. Please pass on all supplied documents
along with the device to anyone else intending
to use it.
Pack contents
We supply the gas alarm with the following
components (see Fig. A ):
1x gas alarm
1x 12 V DC mains adapter
1x mounting fixture
2x fastening screws
2x wall plugs
1x operating instructions
Features
On the front of the casing (see Fig. A):
a
Front of casing
b
Piezo siren opening
c
ALARM LED
d
POWER LED
e
FAULT LED
f
12 V DC mains adapter connecting cable
GB 43
Y
Possible source of escaping gas
(consumer appliance)
Pravděpodobný zdroj
výstupu plynu (spotřebič)
Možný zdroj
úniku plynu (spotrebič) Możliwe
Position for methane
(town gas/natural gas): high
Umístění při metanu(městském plynu/
zemním plynu): nahoře
Umiestnenie pri metáne
(svietiplyn/zemný plyn): hore
Position for liquid gas (propane/
butane): low
Umístění u kapalného plynu
(propanu/butanu): dole
Umiestnenie pri kvapalnom plyne
(propán/bután): dole
KOE217_GA617_Cover_LB4B.indd 4-6 19.09.2007 12:37:36 Uhr
On the rear of the casing (see Fig. B):
g
Rear of casing
h
Mounting fixture
i
12 V DC terminal screws
j
Cable guide
k
Side and lower sensor openings
Technical data
Gas alarm:
Power supply: 12 Volt DC (±10%)
mains adapter (deliv-
ered with the gas
alarm) or on-board
power supply system
Current consumption: max. 150 mA
Gas sensor: hot-wire method
Sensitivity/alarm
threshold: corresponds to a con-
centration of approx.
12 % of the relevant
lower explosive limit
Propane: 0.2 %
Butane: 0.17 %
Methane
(town gas/natural gas): 0.53 %
Alarm signal: loud high-frequency
tone
Volume: 85 dB(A) 3m
Operating temperature: -10 °C to +40 °C
Relative air humidity: max. 95 %
Material: ABS plastic
Dimensions: 35 x 85 x 85 m (h x w x l)
Weight: approx. 100 g
Protection class: III
Mains adapter (delivered with the gas
alarm):
Power supply: 230 V ~ 50 Hz
Current consumption: 60 mA
mACurrent output: 12 Volt DC 300 mA
Connecting cable length: approx. 2 m
Safety instructions
The following instructions are for your own
safety and satisfaction when operating the GA
617 gas alarm. Please note that non-compli-
ance with these safety instructions can lead to
a serious risk of accident.
Explanation of the symbols and terms
used:
c Danger! Failure to observe this instruc-
tion endangers life and health.
m
Caution! Failure to observe this instruc-
tion poses a risk to property.
c Danger!
5
GB
KOE217_GA617_Content_LB4B.indd 5 21.11.2007 9:23:41 Uhr
• Donotleavesmallchildrenunsupervised
with the packaging material. Danger of
suffocation.
• Donotleavechildrenunsupervisedwith
the device. Danger to life and risk of injury.
• Donotdamageanygas,electricityor
telecommunication lines when fitting the
device. Danger to life and risk of injury
and damage.
• Neverexposethedevicetore,heatorto
temperatures of over 50° C for any length
of time. Danger to life from explosion.
• Makesurethatyourhearingisnot
exposed to the loud alarm signal for any
length of time. This can cause serious
damage to the hearing.
• Makesurethatthealarmsignalisnot
triggered close to the ears. This can
cause serious damage to the hearing.
• Handletheconnectingcablewithcare.
Install it so that it cannot get damaged
and does not create a stumbling hazard.
Otherwise there is danger to life and a
risk of injury and fire.
What to do in the event of a gas leak
Please proceed as follows if the gas alarm sig-
nals a gas leak or if you smell gas:
• Donotigniteanynakedlights.Extinguish
any burning tobacco or candles etc.
immediately.
• Intheeventofagasleak,donotswitch
anyelectricaldevices(lightswitch,torch,
doorbell,telephone,intercom,orother
electric consumers) on or off.
• Donotunderanycircumstancesdiscon-
nect the gas alarm from the power supply.
• Immediatelywarnallpeopleatriskand
make sure that they evacuate the area to
safety.
• Shutoffthegassupplyonthemaingas
tap or bottle valve.
• Openthewindowsanddoorsandairthe
room,thehouse,thecaravan,etc.thor-
oughly.
• Noteonairingrooms:certaingases(pro-
pane and butane) are heavier than the
ambientair,andsomearelighter(meth-
ane).Whenairing,pleasemakesurethat
the intake of air is suitable for the proper-
ties of the gas.
• Ifleakinggasisindicatedconstantlyor
repeatedly,pleasecontactyourenergy
provider. Do not use the telephone or any
other electrical device near or around the
gas leak to notify the provider.
• Thegasleakmustonlybedealtwithbya
qualified and authorized expert.
m
Caution
• Ifyouareuncertainwhichtypeofgasyou
use or you have problems installing the
gas alarm you must have the device
installed by a suitably qualified person.
• Onlyconnectthedeviceto12VDC!
Check before connecting the 12 V DC
adapter to the mains that the electricity
supply to the device is protected by the
appropriate fuse or trip in accordance
with the applicable regulations.
• Thisdevicedoesnotserveasprimary
explosion protection as defined by the
guidelines of the employer’s liability insur-
ance associations.
•
Do not cover the device with any object. This
could diminish the performance of the sensor.
• Makesurethatthedevicedoesnotcome
into contact with moisture.
• Protectthedevicefromstrongmagnetic
or electric fields.
• Protectthedevicefromheavymechanical
strain and shocks.
• Onlyusethedevicewiththesupplied
original parts or parts that are designed for it.
• Checkbeforeinitialoperationthatall
components are assembled in accord-
ance with the operating instructions.
• Beforeassemblyandinitialoperationof
thedevice,checkthatthecontentsare
complete and undamaged.
• Thedevicemustonlyberepairedbyauthor-
ized and skilled specialists. Failure to observe
this instruction risks damage resulting from
improper use and loss of the warranty.
• Positionthedevicesothatthesensors
can detect escaping gas.
• Onlyusewithinthetemperaturerange
specified in the „Technical Data“ section.
Higher or lower temperatures can diminish
performance.
• Donotopenthedevice.Openingthe
device will lead to expiry of the warranty.
• Forconnectionincars,caravansoron
boats,tthe(12VDC)powersupply
cable with a switch approved for this pur-
pose.
• Connectthe12VDCterminalscrews
i
either to the mains adapter supplied with
the gas alarm or a 12 V DC power supply
sourceincars,caravansandboats.Dual
connection (parallel connection) will dam-
age the mains adapter.
• Forconnectiontothe12VDCbattery,t
the 12 V DC connecting cable with a fuse
(250 mA).
• Detachthepagecontainingtheinforma-
tion“IMPORTANTADVICE”fromtheoper-
ating manual. Fix this page where it can
be easily seen on the wall directly adja-
7
GB
6
GB
KOE217_GA617_Content_LB4B.indd 6-7 21.11.2007 9:23:41 Uhr
cent to the gas alarm and write on it the
date you first used the alarm.
• Writethedateofrstuseinthespace
provided on the label on the side of the
gas alarm.
Initial operation
Preparation and materials required:
The stated materials are not included in the
delivery scope. The information provided here
is non-binding and intended as a guide. The
material depends on individual local requirements.
You will need:
o
Power supply: 12 V DC mains adapter
connectiontoa230V~50Hzsocket,or
12 V DC on-board power supply system.
o
A crosstip screwdriver for installation with
the fastening screws.
o
A pen to mark the installation points.
o
A drill for the mounting holes.
o
An in-line fuse holder (250 mA/slow-acting
fuse) – only for connection to on-board
supply system.
Selecting the installation position
Whenthereisanescapeofgas,thegasdetector
can only give the alarm if it is reached by the
escaping gas. Anything which prevents gas from
entering the alarm housing can result in the
alarm being given only after a delay or not at all.
Select an installation position that is as close as
possibletothegasappliance,butnotfarther
away than 4 m (liquefied petroleum gases) or 6
m (methane) (see Fig. C). Make sure that the
mains socket for connection of the 12 V DC
mains adapter is located max. 2 m away from
the installation position of the gas alarm. To
detecttown,naturalandmethanegas,theinstal-
lation position should be as far up on the wall as
possible. The gas alarm should be mounted
15-30 cm below the room ceiling and must be
higher than the highest door or window opening.
The gases in question are lighter than air and
therefore rise.
Todetectpropaneandbutanegas,choosea
low installation position on the wall. It should
be 15-30 cm above the floor. Liquid gases are
heavier than air and therefore sink to the floor
and spread from there.
cDo not under any circumstances install
the gas alarm in any of the following
places:
o
Outsidebuildings,e.g.toguardopen
crates of bottled gas.
o
Enclosedspaces(e.g.incupboardsor
behindcurtains),whichcouldpreventthe
alarm from responding in the event of a
gas leak.
o
Directly next to an oven.
o
Directly above a washbasin or drain.
o
Nexttoadoor,window,ventilation,fan,air
conditioningunit,etc.
o
Areas in which the temperature can fall
below –10° C or rise above +50°C or in
which air humidity can rise above 95%.
o
Areas in which dust or dirt can clog the
sensor.
o
Any position in which it could accidentally
get damaged or pulled down.
o
Areas under the risk of explosion.
Power supply
c Danger! Ensurethatnovoltageispresent
when connecting to the power supply and
during installation.
o
Only operate the gas alarm connected to
a 12 V DC power supply. Connect it either
with the 12 V DC mains adapter (included
in the delivery scope) or to a 12 V DC on-
boardpowersupplysystemofacar,cara-
van or boat.
o
Check before connecting the 12 V DC
adapter to the mains that the electricity
supply to the device is protected by the
appropriate fuse or trip in accordance
with the applicable regulations.
12 V DC mains adapter
o
Lead the bare cable ends (approx. 8 mm)
of the 12 V DC connecting cable
f
from
the 12 V DC mains adapter to the terminal
screws
i
in the cable guide
j
. The
cable guide provides strain relief.
o
Attach each cable end to a terminal screw
i
. The polarity is not important for this
connection.
12 V DC on-board power supply system
o
Remove the connecting cable of the mains
adapter from the terminal screws
i
.
o
Equiptheconnectingcableforthepower
supply(12VDC)incars,caravansor
boats with a switch.
o
Lead the bare cable ends (approx. 8 mm)
of the 12 V DC connecting cable of the
12 V DC power source to the terminal
screws
i
in the cable guide
j
. The
cable guide helps to prevent strain on the
connections.
o
Attach each cable end to a terminal screw
i
.
The polarity is not important for this con-
nection.
o
Important information regarding on-board
operation: only one power supply may be
connected to the terminal screws
i
,
even if the mains adapter is not plugged
in. The mains adapter will be damaged if
9
GB
8
GB
KOE217_GA617_Content_LB4B.indd 8-9 21.11.2007 9:23:41 Uhr
a dual connection (parallel connection) is
made.
Installation
c Danger: make sure that the gas alarm is
not powered during installation.
o
Remove the mounting fixture
h
from the
rear side of the casing
g
by sliding it
downwards (see Fig. B).
o
Mark the installation position with the aid
of the two round holes in the mounting
fixture
h
.
o
Install the mounting fixture
h
in the cho-
sen and marked position using the fas-
tening screws and wall plugs supplied
with the gas alarm.
o
Push the gas alarm flush from above onto
the mounting fixture
h
.
Operation
Once the power supply has been connected
properly,anautomaticself-testiscarriedout:
the gas alarm emits several loud alarm signals
andatthesametimetheredALARMLED
c
on the front of the casing
a
flashes. The green
POWERLED
d
then lights up to indicate that
the device is ready for operation (see Fig. A)
12 V DC mains adapter
Switching on:
o
Plug the mains adapter directly and fully
into a 230 V~50 Hz mains socket. Do not
use any type of tabletop socket or exten-
sioncable,sincethesecancauseinter-
ruptions in the power supply.
Switching off:
o
Remove the mains adapter from the
mains socket.
12 V DC on-board supply system
Switching on:
o
Switch the 12 V DC on-board power supply
on.
Switching off:
o
Switch the 12 V DC on-board power supply
off.
Alarm in the event of a gas leak
The gas alarm detects a gas leak with the
sensor. If the concentration of gas at the sensor
exceeds the pre-set sensitivity threshold on
thegasalarm,thealarmresponds:thered
ALARMLED
c
flashes and the loud alarm
signal is emitted.
The alarm continues until the gas concentration
falls back to below the pre-set sensitivity level.
Follow the instructions in the section
„What to do in the event of a gas leak“
Function test
Use a gas lighter to test the function of the gas
alarm.
o
Allow gas to escape from the gas lighter
directly next to the lower or side sensor
opening
k
.
o
Make sure that there is no flame on the
lighter. The gas alarm detects the gas
with the sensor. If the gas concentration
at the sensor exceeds the pre-set sensi-
tivitythreshold,thealarmresponds:the
redALARMLED
c
flashes and the loud
alarm signal is emitted.
o
Do not allow any more gas to escape
from the lighter once the gas alarm has
responded.
The alarm continues until the gas con-
centration falls back to below the pre-set
sensitivity level.
Fault indicator
The device carries out a self-checking routine
for your safety. Possible errors are displayed
bytheFAULT-LED
e
flashing and a coincident
beeping noise from the device.
This fault indicator may also be triggered by
the gas alarm’s surroundings or by an internal
problem inside the device.
If a fault is indicated you must check first:
o
Whether the ambient temperature is out-
side the specified range (-10° C to +40° C).
o
Whether chemicals present in the air may
havecausethefault,e.g.ahighconcen-
tration of acid or alcohol. If this cannot be
conrmed,thentrythedeviceinanother
room. If no fault is indicated there then
the problem lies in the surroundings.
If the fault indicator is still active then the
problem lies within the device itself:
o
The gas alarm has suffered internal damage.
o
The gas alarm can be used for approxi-
mately 5 years.
Then it should be replaced.
11
GB
10
GB
KOE217_GA617_Content_LB4B.indd 10-11 21.11.2007 9:23:41 Uhr
Maintenance and cleaning
c Danger: make sure that the gas alarm is
not live when maintaining or cleaning the
device.
o
Clean the casing of the gas alarm with a
dust cloth or a damp cloth. Use a mild
detergent (no solvents) to clean the plastic
surface.
o
Remove all deposits of dust from the sensor
openings regularly with a brush.
o
Check regularly that the device is working
properly (see section „Function test“).
o
Replace the gas alarm after it has been in
use for approximately 5 years.
Disposal
Please take all packaging materials to a dis-
posal facility in your city or district.
InaccordancewithEuropeanDirective
2002/96/EConusedelectricalandelectronic
appliances and its implementation in national
law,usedelectricalappliancesmustbecollected
separately and recycled in an ecologically
compatible manner.
Please dispose of the alarm at the end of its
useful life at a disposal facility in your city or
district.
Warranty
This device has a warranty of 3 years from the
date of purchase. The device was manufac-
tured with care and inspected thoroughly
before delivery. Please keep your receipt as
proof of purchase. If you have a claim under
thewarranty,pleasecontacttheserviceofce
for your country. This is the only way to ensure
that your device can be sent in free of charge.
This warranty is only valid for the first pur-
chaser and is not transferable.
The warranty furthermore covers material or
manufacturing defects only. It does not apply
to wear parts or damage to fragile parts. The
product is solely intended for private use and
notforcommercialuse.Noclaimfordamages
may be brought in the event of fire or explo-
sion. An alarm is no substitute for insurance
cover and does not replace your duty of care.
In the event of incorrect and / or improper han-
dling,theuseofforceoranyworkonthe
device that is not performed by the service
ofce,thewarrantyshallexpire.Thiswarranty
does not restrict your statutory rights.
Troubleshooting
Fault Cause Remedy
The gas alarm responds
when there is no actual
gas leak.
The gas alarm will respond to
fumesfromcleaningagents,
paint,lacquers,sprays,cooking
fumes,tobaccosmokeand
smoke from candles.
Remove the source of the
fumes.
The gas alarm fails the
function test.
The service life of the gas
alarm expires after approx.
5 years of operation.
Replace the gas alarm.
The gas alarm does not
work.
The power supply is faulty. Make sure that the power
supply is free of faults.
FAULT-LED flashes See section on
“Faultdisplay”
See section on
“Faultdisplay”
13
GB
12
GB
KOE217_GA617_Content_LB4B.indd 12-13 21.11.2007 9:23:41 Uhr
Service
Information on dealing with problems can be
found under www.dexaplan.com.
Ifyouhaveanyquestions,pleasecontactour
service office by email (ser[email protected])
or by telephone (
T 0870 241 3029; Mon-
day - Friday between 8.30 and 17.00).
Here you can obtain all necessary information
onservicequestionssuchasreturns,etc.
Declaration of conformity
This product satisfies the requirements of the
validEuropeanandnationaldirectives(Electro-
magneticCompatibility89/336/EECand
Low-VoltageDirective73/23/EEC).Itscon-
formity has been verified.
Dexaplan GmbH
Paul-Böhringer-Str. 3 · D-74229 Oedheim
Information last updated 11/2007
Ident.-No.:11-2007-GA-617-GB
15
CZ
14
GB
KOE217_GA617_Content_LB4B.indd 14-15 21.11.2007 9:23:42 Uhr
17
CZ
16
CZ
Úvod
Použití ke stanovenému účelu
c
Rozsah dodávky
Vybavení
Přední strana pouzdra (viz obr. A):
a
b
c
d
e
f
Zadní strana pouzdra (viz obr. B):
g
h
i
j
k
Technické údaje
Alarm plynu:
6
Síťový díl (zahrnut v rozsahu dodávky):
KOE217_GA617_Content_LB4B.indd 16-17 21.11.2007 9:23:42 Uhr
19
CZ
18
CZ
Bezpečnostní pokyny
Vysvětlivky použitých znamének a
pojmů:
c Nebezpečí!
m
Pozor!
c Nebezpečí!
•
•
•
•
•
•
•
Chování při výstupu plynu
•
•
•
•
•
•
•
•
•
c Pozor!
•
•
•
•
•
•
•
•
•
•
KOE217_GA617_Content_LB4B.indd 18-19 21.11.2007 9:23:42 Uhr
21
CZ
20
CZ
•
•
•
•
•
•
i
•
•
Uvedení do provozu
Příprava a potřebný materiál:
o
o
o
o
o
Volba místa montáže
c
Montáž alarmu plynu neveďte v
žádném případě na následujících
místech:
o
o
o
o
o
o
o
o
o
KOE217_GA617_Content_LB4B.indd 20-21 21.11.2007 9:23:42 Uhr
23
CZ
22
CZ
Napájení proudem
c Nebezpečí!
o
o
Síťový díl 12 V DC
o
f
j
i
o
i
Síťový díl 12 V DC
o
i
o
o
j
i
o
i
o
Důležité upozornění k provozu
palubní proudové sítě!
i
Montáž
o
h
g
o
h
o
h
o
h
Obsluha
c
a
d
Síťový díl 12 V DC
o
o
Zásobování proudem palubní sítě
12 V DC
o
o
Alarm při výstupu plynu
c
Chování při výstupu plynu!
KOE217_GA617_Content_LB4B.indd 22-23 21.11.2007 9:23:42 Uhr
25
CZ
24
CZ
Funkční test
o
k
o
c
o
Zobrazení chyb
e
o
o
o
o
Odstranění chyb
Chyba Příčina Odstranění
Alarm plynu signalizuje
výstup plynu bez
skutečného výstupu plynu.
Alarm plynu nesplňuje
funkční test.
Alarm plynu nefunguje.
FAULT LED bliká
KOE217_GA617_Content_LB4B.indd 24-25 21.11.2007 9:23:42 Uhr
27
CZ
26
CZ
Údržba a čistění
c Nebezpečí!
o
o
o
o
Zlikvidování
Záruka
Servis
T
Prohlášení o shodnosti
KOE217_GA617_Content_LB4B.indd 26-27 21.11.2007 9:23:43 Uhr
29
SK
28
KOE217_GA617_Content_LB4B.indd 28-29 21.11.2007 9:23:43 Uhr
31
SK
30
SK
Úvod
Použitie podľa určenia
c
Rozsah dodávky
Vybavenie
Predná strana krytu (pozri obr. A):
a
b
c
d
e
f
Zadná strana krytu (pozri obr. B):
g
h
i
j
k
Technické údaje
Plynový alarm:
6
Sieťový zdroj (súčasť dodávky)
KOE217_GA617_Content_LB4B.indd 30-31 21.11.2007 9:23:43 Uhr
33
SK
32
SK
Bezpečnostné pokyny
Vysvetlenie použitých znakov a pojmov:
c Nebezpečenstvo!
m
Pozor!
c Nebezpečenstvo!
•
•
•
•
•
•
•
Správanie sa pri úniku plynu
•
•
•
•
•
•
•
•
•
m
Pozor!
•
•
•
•
•
•
KOE217_GA617_Content_LB4B.indd 32-33 21.11.2007 9:23:43 Uhr
35
SK
34
SK
•
•
•
•
•
•
•
•
•
•
i
•
•
•
Uvedenie do prevádzky
Príprava a potrebný materiál:
o
o
o
o
o
Výber montážneho miesta
c
Montáž plynového alarmu
nevykonávajte v žiadnom prípade
na nasledovných miestach:
o
o
o
KOE217_GA617_Content_LB4B.indd 34-35 21.11.2007 9:23:43 Uhr
37
SK
36
SK
o
o
o
o
o
o
Napájanie
c Pozor nebezpečenstvo!
o
o
Sieťový zdroj 12 V DC
o
f
j
i
o
i
Palubné napájanie 12 V DC
o
i
o
o
j
i
o
i
o
Dôležitý pokyn pre prevádzku
s palubným napájaním!
i
Montáž
o
h
g
o
h
o
h
o
h
Manipulácia
c
a
d
12 V DC sieťový zdroj
o
o
12 V DC Palubné napájanie
o
o
Alarm pri úniku plynu
c
KOE217_GA617_Content_LB4B.indd 36-37 21.11.2007 9:23:43 Uhr
39
SK
38
SK
Správanie sa pri úniku plynu!
Test funkčnosti
o
k
o
c
o
Hlásenie poruchy
e
o
o
o
o
Odstránenie chyby
Chyba Príčina Odstránenie
Plynový alarm signalizuje
únik plynu bez
skutočného úniku plynu.
Plynový alarm neobstojí v
teste funkčnosti.
Plynový alarm nefunguje.
Bliká dióda „Porucha“
KOE217_GA617_Content_LB4B.indd 38-39 21.11.2007 9:23:43 Uhr
Stránka sa načítava ...
Stránka sa načítava ...
Stránka sa načítava ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
DEXAPLAN GA 617 - 11-2007 Dôležitá informácia
- Typ
- Dôležitá informácia
- Táto príručka je tiež vhodná pre
V iných jazykoch
Súvisiace články
Ďalšie dokumenty
-
Dometic GROUP MagicSafe MSG150 Návod na inštaláciu
-
ELRO RM334 Používateľská príručka
-
Dometic MagicSafe MSG150 Návod na používanie
-
Brooks QMBC Návod na používanie
-
Varian Turbo-V 2K-G Používateľská príručka
-
Brooks SLA5840, Revision B Návod na používanie
-
GEV FlammEx FMG 4313 Používateľská príručka
-
Electrolux EFA90950X Používateľská príručka
