Parkside PFBS 10.8 A1 Operation and Safety Notes

IAN 270218

CORDLESS MULTI-GRINDER PFBS 10.8 A1

AKKU-FEINBOHRSCHLEIFER

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

CORDLESS MUL TI-GRINDER

Operation and Safety Notes

Translation of the original instructions

AKUMULATOR O WA SZLIFIERKO-WIERTARKA

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

AKUMULATORSKI BRUSILNIK

IN VRTALNIK ZA FINOMEHANIKO

Navodila za upravljanje in varnostna opozorila

Prevod originalnega navodila za uporabo

AKU JEMNÁ VRTACÍ BRUSKA

Pokyny pro obsluhu a bezpečnostní pokyny

Překlad originálního provozního návodu

AKUMULÁTOROVÁ VŔTACIA BRÚSKA

Pokyny pre obsluhu a bezpečnostné pokyny

Preklad originálneho návodu na obsluhu

AKKUS MULTICSISZOLÓ

Kezelési és biztonsági utalások

Az originál használati utasítás fordítása

GB Operation and Safety Notes Page 5

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 19

HU Kezelési és biztonsági utalások Oldal 35

SI Navodila za upravljanje in varnostna opozorila Stran 49

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 63

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 77

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 91

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funk cjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funk cióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

AKUMULATOROWA SZLIFIERKO-WIERTARKA

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

6

8

3

7

D

E

F

G H

18

4

1 2

5

A CB

16

14

15

19

22

20

21

12

23

13

18

17

9

11

11a

10

5 GB

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 6

Technical information .......................................................................................................................... Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 9

Safety instructions for all operations .................................................................................................. Page 9

Further safety instructions for all operations ......................................................................................Page 11

Additional safety instructions for grinding and cutting-off operations .............................................Page 11

Special safety advice for working with wire brushes ........................................................................Page 12

Safety advice applicable specifically to cordless multi-grinders ......................................................Page 12

Safety notices for chargers ................................................................................................................. Page 13

Operation

Charging the battery pack .................................................................................................................Page 13

Inserting / removing the battery pack into / out of the drill / grinder ................................................Page 13

Reading off the battery status .............................................................................................................Page 13

Inserting or replacing a tool / collet ...................................................................................................Page 14

Switching on and off / Setting the speed range ................................................................................Page 14

Advice on working with materials / Tools / Speed ranges ...............................................................Page 14

Tips and tricks ...................................................................................................................................... Page 15

Maintenance and cleaning

Maintenance .......................................................................................................................................Page 15

Cleaning ..............................................................................................................................................Page 15

Service ...............................................................................................................................................Page 16

Warranty .........................................................................................................................................Page 16

Disposal ............................................................................................................................................Page 16

Translation of the original declaration of conformity /

Manufacturer ............................................................................................................................... Page 17

6 GB

Introduction

Introduction / General safety advice for electrical power tools

Cordless multi-grinder

PFBS 10.8 A1

Q

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Q

Proper use

The rechargeable precision rotary tool with the cor-

responding accessory (as supplied) is intended to

be used for drilling, milling, engraving, polishing,

cleaning, grinding, cutting and sawing materials

such as wood, metal, plastic, ceramics or stone in

dry environments. Any other use or modiﬁcation to

the drill / grinder shall be considered as improper

use and could give rise to considerable dangers.

The manufacturer will not accept liability for loss or

damage arising from improper use. Not intended

for commercial use.

Q

Features and equipment

Cordless multi-grinder:

1

Rotational speed control

2

Battery-operated LED

3

Battery pack release button

4

Battery pack

5

ON / OFF switch

6

Clamping nut

7

Spigot nut

8

Spindle lock

Battery charger (see Fig. A):

9

Charging cradle

10

Mains adapter

11

Charge indicator red

11 a

Charge indicator green

Accessories (see Fig. B):

12

6 HSS drills

13

2 Mandrels for mounting tools

14

3 Polishing wheels

15

4 Grinding wheels

16

1 Metal brush

17

16 Cutting wheels

18

5 Collets

19

2 Plastic brushes

20

3 Milling bits

21

2 Engraving bits

22

5 Grinding bits

23

Combination tool

Q

Included items

1 Cordless multi-grinder with rechargeable

battery pack

1 Charging cradle with mains adapter

1 Accessory kit (50-piece)

1 Operating instructions

Q

Technical information

Model PFBS 10.8 A1:

Rated voltage: 10.8 V

Rated speed: n 5000–25000 min

-1

Max. disc ø: 25 mm

Collet capacity

: max. ø 3.2 mm

Rechargeable battery pack PFBS 10.8 A1-1:

Rated voltage: 10.8 V

Capacity: 1300 mAh

Type: LITHIUM-ION

Battery charger PFBS 10.8 A1-2:

Primary (Input):

Rated voltage: 230–240 V∼, 50–60 Hz

Rated input: 9 W

Secondary (Output):

Rated voltage: 12.6 V

Charging current: 450 mA

7 GB

Introduction

Introduction / General safety advice for electrical power tools

Charging duration: approx. 3 hours

Protection class: II /

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level L

pA

: 66 dB(A)

Sound power level

L

WA

: 77 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Evaluated acceleration, typical:

Hand / arm vibration: 3.583 m / s

2

Uncertainty K = 1.5 m / s

2

Note: The vibration level speciﬁed in these instruc-

tions was measured in accordance with an EN 60745

standardised measurement process and can be used

to compare equipment. The vibration emission value

speciﬁed can also serve as a preliminary assessment

of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make

it easy to underestimate the vibration.

Try to keep the vibration loads

as low as possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the work-

ing time. Wherein all states of operation must be in-

cluded (e.g. times when the power tool is switched

oﬀ and times where the power tool is switched on but

running without load).

Q

General safety advice for

electrical power tools

Read

all the safety advice

and instructions! Failure

to observe the safety advice and instructions may

result in electric shock, ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) K

eep your working area clean and wel

l

lit. Untidy or poorly lit working areas can lead

to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases o

r

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or

on the power supply) must ﬁt the

mains

socket. Never modify the plug in any

way. Never use adapter plugs with

earthed power tools. Unmodiﬁed plugs

and the correct sockets reduce the risk of elec-

tric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.

g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

8 GB

General safety advice for electrical power tools

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

e) When working outdoors with an elec-

trical power tool always use extension

cables that are also approved for use

outdoors. The use of an extension cable suit-

able for outdoor use reduces the risk of elec-

tric shock.

f) Use a residual current device (RCD) for

protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b)

Wear personal protective

equipment and always wear

safety glasses. The wearing of

personal protective equipment such as dust

masks, non-slip safety shoes, safety helmets or

ear protectors, appropriate to the type of elec-

trical power tool used and work undertaken,

reduces the risk of injury.

c) Avoid accidental starting. Verify the po-

wer tool is switched oﬀ before connec-

ting it to the mains and / or connecting

the battery, picking it up, or carrying it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will

be in a better position to control the device in

unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4. Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use

the device if he or she is not familiar with

it or has not read the instructions and

advice. Electrical power tools are dangerous

when they are used by inexperienced people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

9 GB

General safety advice for electrical power tools

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the cord-

less electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable

battery units if they are misused. If this

happens, avoid contact with the ﬂuid.

If contact occurs, ﬂush the aﬀected area

with water. Seek additional medical

help if any of the ﬂuid gets into your

eyes. Escaping battery ﬂuid may cause skin

irritation or burns.

CAUTION! DANGER OF EXPLOSION!

The batteries must never be recharged!

Protect the battery against

heat, e.g., against continuous

intense sunlight, fire, water

and moisture. Danger of explos

ion.

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety instructions for all

operations

Safety warnings common for grinding,

sanding, wire brushing, polishing, carving

or abrasive cutting-off operations:

a) This power tool is intended to function

as a grinder, sander, wire brush, pol-

isher, carving or cut-off tool. Read all

safety warnings, instructions, illustra-

tions and specifications provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

fire and / or serious injury.

b) Do not use accessories which are not

specifically designed and recommend-

ed by the tool manufacturer. Just because

the accessory can be attached to your power

tool, it does not assure safe operation.

c) The rated speed of the grinding acces-

sories must be at least equal to the

max-

imum speed marked on the power

tool.

Grinding accessories running faster than their

rated speed can break and fly apart.

d) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

10 GB

General safety advice for electrical power tools

correctly sized accessories cannot be ade

quately

controlled.

e) The arbour size of wheels, sanding

drums or any other accessory must

properly fit the spindle or collet of the

power tool. Accessories that do not match

the mounting hardware of the power tool will

run out of balance, vibrate excessively and may

cause loss of control.

f) Mandrel mounted wheels, sanding

drums, cutters or other accessories

must be fully inserted into the collet

or chuck. If the mandrel is insufficiently held

and / or the overhang of the wheel is too long,

the mounted wheel may become loose and be

ejected at high velocity.

g) Do not use a damaged accessory. Be-

fore each use inspect the accessory

such

as abrasive wheels for chips and cra

cks,

sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked

wires. If power tool or accessory is

dropped, inspect for damage or install

an undamaged accessory. After in

spect-

ing and installing an accessory, position

yourself and bystanders away from

the plane of the rotating accessory

and

run the power tool at maximum no-

load

speed for one minute. Damaged accesso-

ries will normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glass-

es. As appropriate, wear dust mask,

hearing protectors, gloves and work-

shop apron capable of stopping small

abrasive or workpiece fragments. The

eye protection must be capable of stopping

flying debris generated by various operations.

The dust mask or respirator must be capable of

filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protec-

tive equipment. Fragments of workpiece or

of a broken accessory may fly away and cause

injury beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an op-

eration where the cutting accessory

may contact hidden wiring or its own

cord. Cutting accessory contacting a «live» wire

may make exposed metal parts of the power

tool «live» and could give the operator an elec-

tric shock.

k) Always hold the tool firmly in your

hand(s) during the start-up. The reaction

torque of the motor, as it accelerates to full

speed,

can cause the tool to twist.

l) U

se clamps to support workpiece wh

en-

ever practical. Never hold a small

work-

piece in one hand and the tool in the

other hand while in use. Clamping a small

workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel

rods, pipes or tubing have a tendency to roll

while being cut, and may cause the bit to bind

or jump toward you.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning accessory may grab the

surface and pull the power tool out of your

control.

o) After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices

are securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss of

control, loose rotating components will be vio-

lently thrown.

p) Do not run the power tool while car-

rying it at your side. Accidental contact

with the spinning accessory could snag your

clothing, pulling the accessory into your body.

q) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust inside

the housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

11 GB

General safety advice for electrical power tools

r) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

s) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or shock.

Further safety instructions

for all operations

Kickback and related warnings

Kickback is a sudden reaction to a pinched or sn

agged

rotating wheel, sanding band, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of

the wheel’s movement at the point of pinching. Abra-

sive wheels may also break under these conditions.

Kickback is the result of power tool misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. The

operator can control kickback forces, if proper

precautions are taken.

b) U

se special care when working corne

rs,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

c)

Do not attach a toothed saw blade. S

uch

blades create frequent kickback and loss of

control.

d) Always feed the bit into the material

in the same direction as the cutting

edge is exiting from the material

(which

is the same direction as the chips are

thrown). Feeding the tool in the wrong direc-

tion causes the cutting edge of the bit to climb

out of the work and pull the tool in the direction

of this feed.

e) When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they be-

come slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the

wheel itself usually breaks. When a rotary file,

high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you

could lose control of the tool.

Additional safety instructions

for grinding and cutting-oﬀ

operations

Safety warnings specific for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recom-

mended for your power tool and only

for recommended applications.

For example: do not grind with the

side of a cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding,

side forces applied to these wheels may cause

them to shatter.

b) For threaded abrasive cones and plugs

use only undamaged wheel mandrels

with an unrelieved shoulder flange that

are of correct size and length. Proper

man-

drels will reduce the possibility of breakage.

c) Do not “jam” a cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading and

susceptibility to twisting or snagging of the wheel

in the cut and the possibility of kickback or w

heel

breakage.

d) Do not position your hand in line with

and behind the rotating wheel. When

12 GB

General safety advice for electrical power tools / Operation

General safety advice for electrical power tools

the wheel, at the point of operation, is moving

away from your hand, the possible kickback m

ay

propel the spinning wheel and the power tool

directly at you.

e) When wheel is pinched, snagged or

when interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

comes to a complete stop. Never att

empt

to remove the cut-off wheel from the

cut while the wheel is in motion other-

wise kickback may occur. Investigate and

take corrective action to eliminate the cause of

wheel pinching or snagging.

f) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if

the power tool is restarted in the workpiece.

g) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight. Supports

must be placed under the workpiece near the

line of cut and near the edge of the workpiece

on both sides of the wheel.

h) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b)

Allow brushes to run at operating spe

ed

for at least one minute before using

them. During this time no one is to

stand

in front or in line with the brush. Loose

bristles or wires will be discharged during the

run-in time.

c) D

irect the discharge of the spinning wir

e

brush away from you. Small particles and

tiny wire fragments may be discharged at high

velocity during the use of these brushes and

may become imbedded in your skin.

Q

Safety advice applicable specif-

ically to cordless multi-grinders

When you use the drill / grinder wear the fol-

lowing protective equipment: safety glasses

and protective gloves.

CAUTION! RISK OF INJURY! The tool

continues to rotate after it has been switched

oﬀ! Avoid contact with rapidly rotating drill /

grinder components.

Securely support the work-

piece. Use clamps or a vice to grip the workpiece

ﬁrmly. This is much safer than holding it in your

hand.

RISK OF INJURY! Never

support yourself by placing your hands near or

in front of the device or the workpiece surface.

A slip can result in injury.

DANGER OF FIRE FROM FLYING

SPARKS!

Abrading metal creates ﬂying sparks. For this

reason, always make sure that nobody is placed

in any danger and that there are no inﬂamma

ble

materials near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person oper-

ating the device and to anyone near the work area.

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or covered

with paint, varnish etc.

Its use as a saw or the use of saw blades with

this device is prohibited.

Do not soak the materials or the surface you are

about to work on with liquids containing solvents.

13 GB

General safety advice for electrical power tools / Operation

General safety advice for electrical power tools

Avoid abrading paints containing lead or other

substances hazardous to health.

Do not machine materials containing asbestos.

Asbestos is a known carcinogen.

Avoid contact with moving sanding or grinding

tools.

Do not machine moist materials or damp surfac

es.

NOTE! Do not allow the tool to come to a stand-

still by overloading it!

RISK OF INJURY! Switch

the device oﬀ and allow it to come to a standstill

before you put it down.

Always keep the device cle

an,

dry and free of oil or grease.

Safety notices for chargers

This appliance can be used by children aged

from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been giv-

en supervision or instruction concerning use of the

appliance in a safe way and understand the

hazards involved. Children shall not play with

the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

The charger is only suitable for

indoor use.

If the mains power cable of this appliance is

damaged, it has to be replaced by the manu-

facturer or its service department or a similarly

qualiﬁed person in order to avoid hazards.

Q

Operation

Never use the device for a purpose for which it was

not intended or with non-original parts / accessories.

The use of tools or accessories other than those rec-

ommended in the operating instructions could lead

to you suﬀering an injury.

Q

Charging the battery pack

NOTE! A battery pack that has been unused for a

while or never been charged must be charged before

reuse or ﬁrst use. The battery pack requires about

3–5 cycles before it can reach its full charge. The

charging process takes about 180 minutes.

CAUTION! RISK OF INJURY!

Always pull

out the mains plug (

mains adapter

10

) before

you

insert the battery pack into or take it out of

the charger.

Insert the battery pack

4

into the charging

cradle

9

. This can only be inserted with the

correct polarity.

Connect the adapter

10

to a mains socket.

The red charge level indicator

11

will light up as

long as the battery pack is being charged. Once

charging is completed the red charge level in-

dicator

11

will extinguish and the green charge

level indicator

11 a

will light up. The battery

pack

4

is ready for use.

CAUTION! Do not charge a battery pack for

a second time in close succession. There is a

danger of overcharging the battery pack.

Q

Inserting / removing the

battery pack into / out of

the drill / grinder

Inserting the battery pack:

Set the ON / OFF switch

5

to position “0”.

Insert the battery pack

4

into the drill / grinder

until it engages.

Removing the battery pack:

Pressing the battery pack buttons

3

at the

sides at the same time allows you to remove

the battery pack

4

.

Q

Reading oﬀ the battery status

The status or residual power is indicated as follows

in the battery-operated LED

2

whenever the appli-

ance is switched on:

RED / ORANGE / GREEN = maximum charge / power

14 GB

Operation / Maintenance and cleaning

Operation

RED / ORANGE = medium-level charge / power

RED = weak charge – recharge battery

Q

Inserting or replacing

a tool / collet

Press the spindle lock

8

and keep it pressed.

Rotate the clamping nut

6

until the lock engages.

Loosen the clamping nut

6

with the combina-

tion key

23

.

If a tool is already inserted, remove it.

First insert the tool you wish to use through the

clamping nut

6

before you insert it into the

collet

18

suitable for the tool shaft.

Press the spindle lock

8

and keep it pressed.

Insert the collet

18

into the threaded insert and

tighten the clamping nut

6

on the thread using

the combination key

23

.

NOTE: Use the screwdriver end of the combi-

nation key

23

to release or tighten the screw of

the mandrels

13

.

Q

Switching on and oﬀ / Setting

the speed range

Switching on / Setting the speed range:

Set the ON / OFF switch

5

to position “I”.

Set the rotational speed control

1

to a position

between „1“ and „MAX.“.

Switching oﬀ:

Set the ON / OFF switch

5

to position “0”.

Q

Advice on working with

materials / Tools / Speed ranges

Use the highest speed when working on steel

or iron with the milling bits.

Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

Use the low speed range for working on plastics

and low-melting point materials.

Use high speeds on wood.

Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Setting the appropriate speed

Symbols

Rotational

speed

control

1

Material

1–3

Plastics and low melting

point materials

6–7

Hardwood

4–5

Stone, Ceramics

Max

Steel

5

Softwood, metal

Examples of appropriate tool selection Function:

Function Accessory Application Projection

(min–max) mm

Drilling

HSS drill

12

Drilling wood 18–25 when us-

ing the smallest

drill the projection

is 10 mm

15 GB

Function Accessory Application Projection

(min–max) mm

Milling Milling bits

20

Various tasks, e.g. hollowing out, gouging,

shaping, grooving or slotting

18–25

Engraving Engraving

bits

21

Making marks, craft projects

(see Fig. D)

18–25

Polishing, derusting

CAUTION!

Use only the lightest

contact pressure of

the tool on the work-

piece.

Metal brush

16

Derusting

9–15

Polishing

wheel

14

Working on various metals and plastics, in

particular noble metals like gold or silver

(see Fig. F)

12–18

Cleaning Plastic brush

19

E.g. cleaning complex plastic housings or

the area around a door lock

9–15

Grinding Grinding

wheels

15

Grinding work on stone, wood; ﬁne work

on hard mate

rials such as ceram

ic or alloyed

steel (see Fig. G)

12–18

Grinding bits

22

10

Cutting and sawing Cutting

discs

17

Cutting metal, plastic or wood

12–18

Operation / Maintenance and cleaning

Operation

Be sure not to exceed the maximum diameter of

composite abrasive wheels and grinding cones

and cylinders with 55 mm thread insert, and

the 80 mm maximum diameter of sandpaper

grinding accessories.

Note: The max. permissible mandrel length is

33 mm.

Store accessories inside the original box or oth-

erwise protect the accessories from damage.

Store accessories dry and away from aggres-

sive media.

Tips and tricks

Applying excessive pressure can cause the in-

stalled tool to break and / or damage the work

piece. Optimal results can be achieved by ap-

plying the tool to the work piece at a steady

speed range and little pressure.

Hold the device with both hands whilst cutting.

Please note the data and information in the

chart to prevent the spindle end touching the

perforated plate of the grinding tool.

Q

Maintenance and cleaning

Q

Maintenance

Before and after a prolonged period of non-use

fully charge the battery pack

4

.

When storing a lithium-ion battery for extended

periods, regularly check the charge. The optimal

charge is between 50 % and 80 %. The optimal

storage climate is cooling and dry.

Q

Cleaning

Clean all the dirt oﬀ the drill / grinder. Use a dry

cloth for cleaning.

16 GB

Translation of the original declaration of conformity / Manufacturer

Service / Warranty / Disposal

Q

Service

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Note: Spare parts not listed (e.g. carbon brushes,

switches) can be ordered through our call centre.

Q

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof

of purchase. In the event of a warranty

claim, please make contact by telephone

with our Service Department. Only in this

way can a post-free despatch for your

goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tampering

not carried out by our authorized service branch. Your

statutory rights are not restricted in any way by this

warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0.10 / minute)

e-mail: kom[email protected]

IAN 270218

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electrical

appliances with your domestic

waste!

According to the European Directive 2012 / 19 / EU,

concerning used electrical and electronic appliances

and its implementation in national law, superannu-

ated electrical appliances must be collected and

disposed of via an environmentally suitable recy-

cling facility.

Li-Ion

Do not dispose of rechargeable

batteries with your household

refuse!

Defective or worn out rechargeable batteries must

be recycled according to Directive 2006 / 66 / EC.

Dispose of batteries and appliances over the existing

collection facilities.

Your local communal or municipal authorities can

provide information on how to dispose of the worn

out appliance.

17 GB

Translation of the original

declaration of conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive (2006 / 42 / EC)

EU Low Voltage Directive (2006 / 95 / EC)

Electromagnetic Compatibility

(2004 / 108 / EC)

RoHS Directive (2011 / 65 / EU)

Applicable harmonized standards

EN 55014-1:2006+A1+A2

EN 55014-2:1997+A1+A2

EN 60335-1:2012

EN 60335-2-29:2004+A2:10

EN 60745-1:2009+A11

EN 60745-2-23:2013

EN 61000-3-2:2006/+A1:2009/+A2:2009

EN 61000-3-3:2013

EN 62233:2008

Type / Appliance Designation:

Cordless multi-grinder PFBS 10.8 A1

Date of manufacture (DOM): 08–2015

Serial number: IAN 270218

Bochum, 31.08.2015

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcat

ions

in the course of further development.

Translation of the original declaration of conformity / Manufacturer

Service / Warranty / Disposal

18

Spis zawartości

19 PL

Spis zawartości

Wstęp

Użytkowanie zgodne z przeznaczeniem .......................................................................................Strona 20

Wyposażenie ...................................................................................................................................Strona 20

Zakres dostawy ................................................................................................................................Strona 20

Dane techniczne ..............................................................................................................................Strona 20

Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 21

2. Bezpieczeństwo elektryczne .......................................................................................................Strona 21

3. Bezpieczeństwo osób .................................................................................................................Strona 22

4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 23

5. Używanie i obchodzenie się z narzędziem akumulatorowym .................................................Strona 23

6. Serwis ...........................................................................................................................................Strona 24

Wskazówki bezpieczeństwa dla wszystkich zastosowań ............................................................Strona 24

Inne wskazówki bezpieczeństwa dla wszystkich zastosowań .....................................................Strona 26

Dodatkowe wskazówki dotyczące bezpieczeństwa podczas szlifowania iprzecinania .......... Strona 26

Szczególne wskazówki dotyczące bezpieczeństwa podczas pracy przy użyciu

szczotek drucianych ........................................................................................................................Strona 27

Wskazówki dotyczące bezpieczeństwa podczas używania dla wiertarko-szlifierek.................Strona 27

Wskazówki dotyczące bezpieczeństwa ładowarek .....................................................................Strona 28

Obsługa

Ładowanie akumulatora Pack .........................................................................................................Strona 28

Założenie / usunięcie akumulatora Pack z urządzenia .................................................................Strona 29

Odczyt stanu akumulatora ..............................................................................................................Strona 29

Narzędzie / tulejka zaciskowa - założenie / wymiana .................................................................Strona 29

Załączenie i wyłączenie / ustawienie zakresu obrotu ...................................................................Strona 29

Wskazόwki dotyczące obrόbki materiału / narzędzi / zakresu obrotu .......................................Strona 29

Pomocne wskazówki........................................................................................................................Strona 31

Konserwacja oraz czyszczenie

Konserwacja .....................................................................................................................................Strona 31

Czyszczenie .....................................................................................................................................Strona 31

Serwis .............................................................................................................................................Strona 31

Gwarancja ..................................................................................................................................Strona 32

Usuwanie ..................................................................................................................................... Strona 32

Tłumaczenie oryginału Deklaracji zgodności WE / Producent ........Strona 33

20 PL

Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi

Wstęp

Akumulatorowa szliﬁerko-

wiertarka PFBS 10.8 A1

Q

Wstęp

Gratulujemy zakupu nowego urządzenia. Tym sa-

mym zdecydowali się Państwo na zakup produktu

wysokiej jakości. Instrukcja obsługi jest częścią tego

produktu. Zawiera ona ważne wskazówki dotyczące

bezpieczeństwa, użytkowania iutylizacji. Przed

pierwszym użyciem produktu należy zapoznać się

ze wszystkimi wskazówkami dotyczącymi obsługi

ibezpieczeństwa. Używać produktu wyłącznie

zgodnie zjego poniżej opisanym przeznaczeniem.

Wprzypadku przekazania produktu innej osobie

należy dołączyć do niego całą jego dokumentację.

Q

Użytkowanie zgodne

z przeznaczeniem

Akumulatorowa szliﬁerko-wiertarka należy używać z

odpowiednimi akcesoriami (takimi, jak dostarczone)

do borowania, frezowania, grawerowania, polero-

wania, czyszczenia, szlifowania, oddzielania od

materiałów takich, jak drewno, metal, tworzywo

sztuczne, ceramika czy kamień w suchych pomiesz-

czeniach. Każde inne zastosowanie lub dokonywa-

nie zmian na urządzeniu uważane jest za sprzeczne

z przeznaczeniem i niesie ze sobą znaczne ryzyko

zagrożenia wypadkiem. Za szkody powstałe na

wskutek zastosowania sprzecznego z przeznacze-

niem, producent nie przejmuje żadnej odpowiedzial-

ności. Nie do użytku komercyjnego.

Q

Wyposażenie

Akumulatorowa szlifierko-wiertarka:

1

Regulacja prędkości

2

Wskaźnik akumulatora LED

3

Przycisk zwalniający akumulator

4

Akumulator Pack

5

Przełącznik ZAŁ. / WYŁ

6

Nakrętka mocująca

7

Nakrętka kołpakowa

8

Blokada trzpienia

Ładowarka (zobacz rys. A):

9

Korytko ładownicze

10

Zasilanie

11

Wskaźnik stanu ładowania czerwony

11 a

Wskaźnik stanu ładowania zielony

Akcesoria (zobacz rys. B):

12

6 Wierteł HSS

13

2 Trzpienie do uchwytόw narzędzi

14

3 Tarcze polerskie

15

4 Tarcze szliﬁerskie

16

1 Szczotka metalowa

17

16 Tarcz do cięcia

18

5 Zaciskόw

19

2 Szczotki z tworzywa sztucznego

20

3 Bity do frezowania

21

2 Bity do grawerowania

22

5 Bitόw do szlifowania

23

Klucz kombi

Q

Zakres dostawy

1 Precyzyjna wiertarko-szliﬁerka akumulatorowa

z zestawem akumulatorów

1 Stacja ładująca z zasilaczem

1 Zestaw akcesorii (50 części)

1 Instrukcja obsługi

Q

Dane techniczne

Model PFBS 10.8 A1:

Napięcie znamionowe: 10,8 V

Obroty:

n 5000–25000 min

-1

Maks. ø tarcz: 25 mm

Zakres mocowania uchwytu

wiertarskiego

: maks. ø 3,2 mm

Akumulator Pack PFBS 10.8 A1-1:

Napięcie znamionowe: 10,8 V

Pojemność: 1300 mAh

Typ: LITOWO-JONOWY

Ładowarka PFBS 10.8 A1-2:

Pierwotnie (Wejście / Input):

Napięcie znamionowe: 230–240 V∼, 50–60 Hz

Obciążenie znamionowe:

9 W

Stránka sa načítava ...

Parkside PFBS 10.8 A1 Operation and Safety Notes

Parkside PFBS 10.8 A1 Operation and Safety Notes

V iných jazykoch

Súvisiace články

Ďalšie dokumenty