Panasonic SC-XH175 Návod na používanie

Značka: Panasonic

Model: SC-XH175

Kategória: Blu-Ray prehrávače

Typ: Návod na používanie

Tento návod je vhodný aj pre

SCXH175EP

[EP]

RQT9597-R

Operating Instructions

Návod k obsluze

Instrukcja obsługi

Használati útmutató

DVD Home Theater Sound System

Systém domácího kina s DVD přehrávačem

Zestaw kina domowego z odtwarzaczem DVD

DVD házimozi hangrendszer

Model No. / Model č. / Nr Modelu / Típusszám SC-XH175

until

2012/02/26

Thank you for purchasing this product.

For optimum performance and safety, please read these instructions

carefully.

Please keep this manual for future reference.

The illustrations shown may differ from your unit.

Děkujeme za zakoupení tohoto výrobku.

Pro dosažení optimálního výkonu a z bezpečnostních důvodu si pečlivě

přečtěte tyto pokyny.

Návod uschovejte k pozdějšímu použití.

Uvedené ilustrace se mohou od vašeho přístroje lišit.

Dziękujemy za zakupienie tego produktu.

Aby zapewnić optymalną pracę urządzenia i jego bezpieczną obsługę,

należy dokładnie przeczytać niniejszą instrukcję.

Należy zachować tę instrukcję obsługi na przyszłość.

Urzdązenie pokazane na ilustracjach może się różnić od

zakupionego urządzenia.

Köszönjük, hogy termékünket választotta.

A biztonság és a készülék optimális teljesítménye érdekében kérjük, hogy

figyelmesen olvassa el a használati útmutatót!

Kérjük, őrizze meg ezt az útmutatót.

Az útmutatóban látható ábrák eltérhetnek az Ön készülékétől.

Region number/Číslo regionu/Numer regionu/Régiókód

The player plays DVD-Video marked with labels containing the

region number “2” or “ALL”.

Přehrávač přehrává disky DVD-Video označené štítky s číslem

regionu “2” nebo “ALL”.

Odtwarzacz obsługuje płyty DVD-Video z numerami regionów “2” lub

“ALL”.

A DVD lejátszó a megfelelő régiókóddal “2” vagy “ALL” jelzéssel

jelölt DVD-Video lemezeket játssza le.

Example/Příklad/Przykład/Például:

2 ALL

The illustration shows SC-PT70.

Obrázek představuje model SC-PT70.

Na rysunku przedstawiono model SC-PT70.

SC-XH175 EP_RQT9597-R_eng.book Page 1 Wednesday, December 14, 2011 9:38 AM

RQT9597

System/Systém/Zestaw/Rendszer SC-XH175

Main unit/Hlavní jednotka/Główne urządzenie/Készülék SA-XH175

Speaker system/Reproduktorový

systém/System głośników/

Hangszóró rendszer

Front speakers/Čelní reproduktory/Głośniki przednie/

Első hangsugárzók

SB-HF185

Center speaker/Centrální reproduktor/Głośnik centralny/Középső

hangsugárzó

SB-HC185

Surround speakers/Prostorové reproduktory/Głośniki dźwięku

przestrzennego/Háttér hangsugárzók

SB-HS190

Subwoofer/Subwoofer/Głośnik niskotonowy/Mélysugárzó SB-HW185

Operations in these instructions are described mainly with the remote control, but you can perform the operations on the main unit if

the controls are the same.

Popis obsluhy v tomto návodu se týká především dálkového ovladače, avšak obsluhu lze provádět také pomocí ovládacích prvků

hlavní jednotky – jestliže jsou stejné jako na ovladači.

W instrukcji obsługi opisano głównie czynności wykonywane z poziomu pilota, można je jednak wykonać z poziomu urządzenia

głównego, jeżeli znajdujące się tam przyciski są takie same.

A használati útmutatóban ismertetett műveletek főleg a távvezérlő használatára vonatkoznak, de ezeket a műveleteket a készülék

kezelőszerveivel ugyanúgy elvégezheti.

Accessories/Příslušenství/Akcesoria/Tartozékok

Please check and identify the supplied accessories.

Zkontrolujte a odlište dodané příslušenství.

Sprawdź załączone akcesoria.

Kérjük, ellenőrizze és azonosítsa a mellékelt tartozékokat.

∏ 1 Remote control/Dálkový ovladač/Pilot/Távvezérlő

(N2QAYB000694)

∏ 1 Remote control battery/Baterie dálkového ovládání/Bateria pilota/Távvezérlő elem

∏ 1 FM indoor antenna/Pokojová anténa FM/Wewnętrzna antena FM/URH szobaantenna

∏ 1 AC mains lead/Sít’ový kabel/Przewód zasilania/Hálózati csatlakozókábel

∏ 1 Sheet of speaker cable stickers/Arch nálepek na kabely reproduktorů/Arkusze nalepek na kable głośnikowe/

Csomag címke a hangsugárzó kábelekhez

∏ 3 Speaker cables/Kabely reproduktorů/Kabel głośnikowe/Hangsugárzó kábelek

∏ 2 Speaker stands (with cable)/Stojany reproduktorů (s kabelem)/Stojaki głośników (z kablem)/Hangsugárzó tartó (kábelekkel)

∏ 2 Bases/Základny/Podstawy/Tartótalp

∏ 8 Screws/šroubů/Wkrętów/Csavar

(Inside of product)

(Uvnitř přehrávače)

(Wewnątrz

urządzenia)

(A készülék

belsejében)

SC-XH175 EP_RQT9597-R_eng.book Page 2 Wednesday, December 14, 2011 9:38 AM

RQT9597



The circled numbers indicated in the operating instructions (e.g. Press [Í]1) correspond to the circled numbers in the above.

Zakroužkovaná čísla uvedená v návodu k obsluze (např. Stiskněte [Í]1) odpovídají zakroužkovaným číslům viz výše.

Zakreślone cyfry zaznaczone w instrukcji obsługi (np. Wciśnij [Í]1) odnoszą się do zakreślonych cyfr w tejże instrukcji.

A használati utasításban feltüntetett bekarikázott számok (pl. Nyomja meg az [Í]1 gombot) a fenti bekarikázott számoknak felelnek meg.

RETURN

VOL

STOP

VOL

INPUT

SKIP

SLOW

PAUSE

PLAY

DVD

RADIO

EXT-IN

EXIT

–REPEAT

PLAY MODE

SOUND

SURROUND FL DISPLAY

1 2 3

4 5 6

7 8

CANCEL

FUNCTIONS

MUTE

SKIP

–SLEEP













































CH SELECT

–W.SRD













SC-XH175 EP_RQT9597-R_eng.book Page 3 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

Other Panasonic audio/video equipment may start functioning when you

operate the unit using the supplied remote control.

You can operate this unit in another mode by setting the remote control

operating mode to “REMOTE 2”.

The main unit and remote control must be set to the same mode.

1 Press [EXT-IN]4 to select “AUX”.

2 Press and hold [< OPEN/CLOSE]2 on the main unit and [2] on the

remote control until the main unit’s display shows “REMOTE 2”.

3 Press and hold [OK]8 and [2] on the remote control for at least 2

seconds.

To change the mode back to “REMOTE 1”, repeat the steps above by

replacing [2] with [1].

Control reference guide

Remote control

1 Turn the main unit on/off (B 9)

2 Select channels and title numbers etc. / Enter numbers

(B 10, 12)

3 Cancel (B 13)

4 Source select

[DVD]: Select disc as the source (B 12)

[RADIO]: Select FM tuner (B 10)

[EXT-IN]: Select external audio as the source (B 10)

AV # AUX # ARC # D-IN # USB

^--------------------------------------------------------------}

5 Basic operations for play (B 12)

6 Display RDS text data / Show on-screen menu (B 10, 14)

7 Show a disc top menu (B 13)

8 Select or confirm menu items / Frame-by-frame (B 12)

9 Select the play mode / Set the repeat mode

(B 13, 14)

: Select sound mode / Turn Whisper-mode Surround on/off

(B 12)

; Select surround sound effects (B 11)

Set the Sleep timer

Press and hold [jSLEEP].

While the time is shown on the main unit’s display, press

[jSLEEP] repeatedly.

Each time you press the button:

SLEEP 30 # SLEEP 60 # SLEEP 90 # SLEEP120

^-------------------------- OFF (Cancel) (------------------------}

≥ To confirm the remaining time, press and hold the button again.

< TV operations

Aim the remote control at the Panasonic TV and press the

button.

[TV, Í]: Turn the TV on/off

[INPUT, AV]: Change the TV’s video input mode

[r, VOL, s]: Adjust the TV volume

This may not work properly with some models.

= Adjust the volume of the main unit

> Mute the sound

≥ “MUTE” flashes on the main unit’s display while the function is on.

≥ To cancel, press the button again or adjust the volume.

≥ Muting is cancelled when you switch the unit to standby.

? Select radio stations manually (B 10)

@ Select preset radio stations (B 10)

A Exit the display

B Show START menu (B 10)

C Show a disc menu (B 13)

D Return to previous screen (B 13)

E Switch information on the main unit’s display (B 13)

F Select speaker channel (B 12)

Avoiding interference with other Panasonic equipment

Main unit

1 Standby/on switch (Í/I)

Press to switch the unit from on to standby mode or vice

versa. In standby mode, the unit is still consuming a small

amount of power.

2 Open/Close the disc tray (B 12)

3 Adjust the volume of the main unit

4 Power indicator

The indicator lights when this unit is turned on.

5 Disc tray

6 Connect USB device (B 16)

7 Remote control signal sensor

8 Display (FL display)

POWER-SAVING FEATURES

The main unit is designed to conserve its power

consumption and save energy.

∫ Auto power-down function

≥The main unit will automatically switch to standby mode

after 30 minutes of inactivity.

e.g.

– There is no audio signal from an external device.

– Media playback is stopped/paused.

– The disc menu is displayed and play is not selected.

(This function may not work depending on the application

type of discs.)

≥When the main unit is turned back on, “POWER ON FROM

AUTO POWER DOWN MODE” appears on the main unit’s

display.

SC-XH175 EP_RQT9597-R_eng.book Page 4 Wednesday, December 14, 2011 9:38 AM

Getting StartedPlaying DiscsOther OperationsReference

RQT9597

ENGLISH

TABLE OF CONTENTS

Getting Started

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Control reference guide. . . . . . . . . . . . . . . . . . . . . . . . . . .4

Quick Start Guide

step 1 Preparing the speakers . . . . . . . . . . . . . . . . . 6

step 2 Positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

step 3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Speaker connections. . . . . . . . . . . . . . . . . . . . . .7

Radio antenna connection. . . . . . . . . . . . . . . . . .7

Audio and video connections . . . . . . . . . . . . . . .8

step 4 AC mains lead connection. . . . . . . . . . . . . . . 9

step 5 Preparing the remote control . . . . . . . . . . . . 9

step 6 Easy setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Listening to the radio. . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Presetting stations automatically . . . . . . . . . . . . . . . . . . . . 10

Listening to a preset channel . . . . . . . . . . . . . . . . . . . . . . . 10

RDS broadcasting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using the START menu . . . . . . . . . . . . . . . . . . . . . . . . . .10

Selecting the source using the remote control . . . . . . . . . . 10

Listening to the TV or other device’s audio from this

unit’s speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Playing Discs

Basic play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playing from the selected item. . . . . . . . . . . . . . . . . . . . 13

Other modes of play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Program and Random play . . . . . . . . . . . . . . . . . . . . . . . . 13

Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using on-screen menus . . . . . . . . . . . . . . . . . . . . . . . . . 14

Other Operations

Linked operations with the TV

(VIERA Link “HDAVI Control

”) . . . . . . . . . . . . . . . . 15

Setting the audio link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Easy control only with VIERA remote control . . . . . . . . . . 16

Playing from an USB device. . . . . . . . . . . . . . . . . . . . . . 16

Reference

Changing the player settings . . . . . . . . . . . . . . . . . . . . . 16

DivX information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Displaying DivX subtitles text . . . . . . . . . . . . . . . . . . . . . . 18

Media that can be played . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Speaker installation option. . . . . . . . . . . . . . . . . . . . . . . 20

Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

POWER-SAVING FEATURES. . . . . . . . . . . . . . . . . . . . .4

Enjoying sound effects from all speakers

Enjoying surround sound effects. . . . . . . . . . . . . . . .11

Selecting sound mode. . . . . . . . . . . . . . . . . . . . . . . . .12

Whisper-mode Surround. . . . . . . . . . . . . . . . . . . . . . .12

Adjusting the speaker level during playback . . . . . .12

Adjusting the speaker balance during playback . . .12

Safety precautions. . . . . . . . . . . . . . . . . . 25

SC-XH175 EP_RQT9597-R_eng.book Page 5 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

Front speakers

Preparation

≥ To prevent damage or scratches, lay down a soft cloth to assemble speakers.

≥ For assembly, use a Phillips-head screwdriver (not supplied).

≥ You will need to obtain the appropriate screw eyes to match the walls or

pillars to which they are going to be fastened.

≥ Consult a qualified housing contractor concerning the appropriate

procedure when attaching to a concrete wall or a surface that may not

have strong enough support. Improper attachment may result in

damage to the wall or speakers.

≥ Use a string of less than ‰2.0 mm, which is capable of supporting over

10 kg.

Caution

≥ Do not stand on the base. Be cautious when children are near.

≥ When carrying the speaker, hold the stand and base parts.

step 1 Preparing the speakers

Speaker assembly option

Make sure you have all the indicated components before starting assembly, setup, and connection.

≥ Keep the screws out of reach of children to prevent swallowing.

≥ For optional wall mount, refer to page 20.

2 Bases 8 Screws2 Front speakers 2 Stands (with cable)





















Slide into the groove.

Tighten securely.

Position the cable

between the ridges.

Leave about 120 mm.

Press into the groove.

Tighten securely.

Insert the wire fully.

i: White

j: Blue line

Push!









Leave about

120 mm.

You can remove and use the

cable from the stand. To reattach

the cable, refer to page 20.

Slide into the

groove.

Press into the groove.

Tighten securely.

Insert the wire fully.

i: White

j: Blue line

Push!

Thread the speaker cable through

the base.

Attach the speaker.

Preventing the speakers from falling

String (not supplied)

Thread from the wall to the speaker and tie tightly.

Speaker (rear)

Screw eye

(not supplied)

Approx.

150 mm

Wall

SC-XH175 EP_RQT9597-R_eng.book Page 6 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting Started

Quick Start Guide

ENGLISH

How you set up your speakers can affect the bass and the sound field.

Note the following points:

≥ Place speakers on flat secure bases.

≥ Keep your speakers at least 10 mm away from the system for proper

ventilation.

≥ Placing speakers too close to floors, walls, and corners can result in

excessive bass. Cover walls and windows with thick curtains.

Setup example (“Surround layout (Recommended)”: Standard

surround placement)

Place the front, center, and surround speakers at approximately the same

distance from the seating position. The angles in the diagram are

approximate.

§1 Position with at least 5 cm of space on all sides for proper ventilation.

§2 Put on a rack or shelf. Vibration caused by the speaker can disrupt

the picture if it is placed directly on the TV.

§3 Place to the right or left of the TV, on the floor or a sturdy shelf so that

it will not cause vibration. Leave about 30 cm from the TV.

Depending on the room layout, you may like to use all the speakers at the

front (“Front layout (Alternative)”) (B 9, Easy setup).

Notes on speaker use

≥Use only supplied speakers

Using other speakers can damage the unit, and sound quality will be

negatively affected.

≥ You can damage your speakers and shorten their useful life if you play

sound at high levels over extended periods.

≥ Reduce the volume in the following cases to avoid damage:

– When playing distorted sound.

– When the speakers are reverberating due to a record player, noise

from FM broadcasts, or continuous signals from an oscillator, test

disc, or electronic instrument.

– When adjusting the sound quality.

– When turning the unit on or off.

If irregular colouring occurs on your TV

The center speaker is designed to be used close to a TV, but the picture

may be affected on some TVs and setup combinations.

If this occurs, turn the TV off for about 30 minutes.

The demagnetising function of the TV should correct the problem. If it

persists, move the speakers further away from the TV.

Turn off all equipment before connection and read the appropriate

operating instructions.

Do not connect the AC mains lead until all other

connections are completed.



Use an FM outdoor antenna if radio reception is poor.

step 2 Positioning

Caution

≥ The main unit and supplied speakers are to be used only as

indicated in this setup. Failure to do so may lead to damage to

the amplifier and/or the speakers, and may result in the risk of

fire. Consult a qualified service person if damage has occurred

or if you experience a sudden change in performance.

≥ Do not attempt to attach these speakers to walls using methods

other than those described in this manual.

120°

60°

Center speaker

§2

Front speaker

(left)

Subwoofer

§3

Surround

speaker (left)

Surround

speaker (right)

Front speaker

(right)

Main unit

§1

step 3 Connections

Speaker connections

Pay attention to the type of speaker and the connector colour when you

place the speakers.

Main unit (rear)

Connect to the terminals of the same colour.

Use of the speaker cable stickers is convenient when making cable

connections.

Speakers (rear)

Insert the wire fully, taking care not to insert beyond the wire insulation.

i: White

j: Blue line

≥ Be careful not to cross (short circuit) or reverse the polarity of the

speaker wires as doing so may damage the speakers.

Radio antenna connection

FM ANT

(75 )

Main unit (rear)

Affix this end of the antenna to a

wall or pillar where the reception is

best.

FM indoor antenna

(supplied)

SC-XH175 EP_RQT9597-R_eng.book Page 7 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

≥ To listen to the TV audio on the sound system, connect the optical

digital audio cable, SCART cable, HDMI

§1

cable or audio cable.

Refer to the operating instructions of the respective devices for the

settings necessary to output the audio.

§1 Only when connecting to an ARC compatible TV.

Refer to “Connection with an ARC compatible TV” for details.

(B below)

This connection provides the best picture and audio quality.

VIERA Link “HDAVI Control”

If your Panasonic TV is VIERA Link compatible, you can operate your TV

synchronising with home theater operations or vice versa

(B 15, Linked operations with the TV).



≥

Use the High Speed HDMI Cables

≥ It is recommended that you use Panasonic’s HDMI cable. Recommended

part number:

RP-CDHS15 (1.5 m), RP-CDHS30 (3.0 m), RP-CDHS50 (5.0 m), etc.

≥ For TV with more than one HDMI terminal, refer to the operating instructions

for the TV to determine which terminal to connect to.

≥ Do not make the video connections through the VCR.

Due to copy guard protection, the picture may not be displayed properly.

(Only Dolby Digital and PCM can be played with this connection.)

∫ Connection with an ARC compatible TV

≥ Refer to the operating instructions of the TV for details.

∫ Connection without an ARC compatible TV

[\\\\\\\\\AUX\\\\\\\\]

Use this connection when the TV does not have an OPTICAL OUT

terminal or when the DIGITAL AUDIO IN OPTICAL terminal on this unit is

being used by the STB.

Connect the audio cable (not supplied) from the AUX terminal on the

main unit to the AUDIO OUT terminal on your TV.

To improve picture quality, you can change the video signal output from

the SCART (AV) terminal to suit the type of TV you are using.

≥ Select “S-Video”, “RGB 1” or “RGB 2” from “Video Out-SCART” in Video

menu (B 17).

≥ When both the HDMI cable and SCART cable are connected, there will

be no RGB output from the SCART (AV) terminal.

Use this connection when you want to output the original surround audio

from your STB, etc. to this unit.

Connect the optical digital audio cable (not supplied) from the

DIGITAL AUDIO IN OPTICAL terminal on the main unit to the

OPTICAL OUT terminal on your STB.

≥ If the DIGITAL AUDIO IN OPTICAL terminal is already in use for the TV

audio, reconnect the TV audio to the AUX terminal using an audio

cable.



If you have various sound sources (such as Blu-ray Disc player, DVD recorder,

VCR, etc.), connect them to the available inputs on the TV and the TV output

should then be connected to the SCART (AV), AUX, HDMI AV OUT

DIGITAL AUDIO IN OPTICAL terminal of the main unit.

Audio and video connections

Recommended connection to a TV

≥ Non-HDMI-compliant cables cannot be utilised.

≥ After connecting with the optical digital audio cable or HDMI

§1

cable, make

settings to suit the type of audio from your digital equipment (B 11).

What is ARC?

ARC is an abbreviation of Audio Return Channel, also known as HDMI

ARC. It refers to one of the HDMI functions. If the TV is ARC

compatible, audio from the TV can be sent to this unit via the HDMI

cable without the need to make an extra audio connection.

HDMI (ARC)

AV OUT

HDMI

(ARC)

OUT

(ARC)

HDMI cable

(not supplied)

Main unit (rear)

Be sure to connect to the

TV’s ARC compatible

terminal. (Refer to the

operating instructions for

the TV.)

Alternative connection to a TV

§2 This connection will also enable you to play TV audio through

your home theater system (B 10, Selecting the source using the

remote control). Select the appropriate audio out (e.g. Monitor)

on the TV.

Set Top Box (cable/satellite/Blu-ray Disc player, etc) connection

AV IN

OPTICAL

OUT

DIGITAL AUDIO IN

OPTICAL

OUT

(ARC)

DIGITAL AUDIO IN

OPTICAL

HDMI AV OUT

HDMI cable

(not supplied)

Optical digital audio

cable (not supplied)

Main unit (rear)

SCART cable

§2

(not supplied)

Main unit (rear)

SC-XH175 EP_RQT9597-R_eng.book Page 8 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting Started

Quick Start Guide

ENGLISH

Conserving power

The main unit consumes a small amount of power, even when it is in

standby mode (approx. 0.4 W). To save power when the unit is not to be

used for a long time, unplug it from the household mains socket.

You will need to reset some memory items when plugging back the main

unit.



The supplied AC mains lead is for use with the main unit only.

Do not use it with other equipment. Also, do not use cords for other equipment

with the main unit.

≥ Use alkaline or manganese batteries.

Aim at the remote control signal sensor (B 4), avoiding obstacles.

Distance: Within approx. 7 m

Angle: Within approx. 20° up and down, approx. 30° to the left and right

The Easy setup screen assists you in making necessary

settings.



≥ You can perform this setup anytime by selecting “Easy setup” in the Setup

menu. (B 18)

≥ If this unit is connected to a “HDAVI Control 3 or later” compatible TV via

HDMI cable, the menu language and TV aspect information will be retrieved

via VIERA Link.

≥ If this unit is connected to a “HDAVI Control 2” compatible TV via HDMI cable,

the menu language information will be retrieved via VIERA Link.

step 4 AC mains lead connection

step 5 Preparing the remote control

Use

AC IN

Main unit (rear)

AC mains lead

(supplied)

To household mains socket

R6/LR6, AA







Press in and lift up.

Replace the cover.

Insert so the poles (r and j) match those in the remote control.

step 6 Easy setup

Preparation

Turn on your TV and select the appropriate video input mode

(e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connection to this unit.

≥ To change your TV’s video input mode, refer to its operating

instructions.

≥ This remote control can perform some basic TV operations (B 4).

Press [Í]1 to turn on the unit.

≥ The Easy setup screen appears automatically.

Press [3, 4]8 to select “Yes” and press [OK]8.

Follow the messages and make the settings with

[3, 4, 2, 1]8 and [OK]8.

≥Language

Select the language used on menu screen.

≥TV aspect

Select the aspect to suit your TV.

≥Speaker layout

Select “Surround layout (Recommended)” mode or “Front layout

(Alternative)” mode according to your speaker layout

(B 7, Positioning).

≥Speaker check

Listen to speaker output to confirm speaker connections.

≥Speaker output

Make surround sound setting for speaker output.

≥TV audio

Select the audio input connection from your TV.

For AUX connection (B 8): Select “AUX”.

For HDMI connection (B 8): Select “ARC”.

For DIGITAL AUDIO IN OPTICAL connection (B 8): Select

“DIGITAL IN”.

For SCART (AV) connection (B 8): Select “AV”.

This will be the TV audio setting for VIERA Link “HDAVI Control”.

(B 15)

Press [OK]8 to finish the “Easy setup”.

SC-XH175 EP_RQT9597-R_eng.book Page 9 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

You can preset up to 30 channels.

The radio settings will be shown on the unit's display. (Some settings are

also indicated on the TV screen.)

Preparation

Make sure that the FM antenna is connected. (B 7)

Select a radio broadcast.

1 Press [RADIO]4 to select “FM”.

2 Press [SEARCH6, SEARCH5]? to select the frequency.

≥To start automatic tuning, press and hold [SEARCH6,

SEARCH5]? until the frequency starts scrolling. Tuning stops

when a station is found.

To preset the channel

3 While listening to the radio broadcast

Press [OK]8.

4 While the frequency is flashing on the display

Press the numbered buttons to select the channel.



A station previously stored is overwritten when another station is stored in the

same channel preset.

The unit can display the text data transmitted by the radio data system

(RDS) available in some areas.

While listening to the radio broadcast

Press [FUNCTIONS]6 to display the text data.

Each time you press the button:

PS: Program service

PTY: Program type

FREQ: Frequency display

§“M.O.R. M”=Middle of the road music



RDS displays may not be available if reception is poor.

You can select sound effects, desired source, change the settings, access

playback/menus, etc., by using the START menu.

When “Input Selection” is selected

You can select a desired source from the menu.

≥ DVD/CD (B 12), FM RADIO (B left), AV

§1

(B below), AUX

§1

(B below), ARC

§1

(B below), DIGITAL IN

§1, 2

(B below),

USB

(B 16)

§1 “(TV)” will appear beside “AV”, “AUX”, “ARC” or “DIGITAL IN”,

indicating the TV audio setting for VIERA Link “HDAVI Control”

(B 15).

§2 “(STB)” will appear beside “DIGITAL IN”, indicating the STB audio

setting for VIERA Link “HDAVI Control” (B 15).

When “Setup”

is selected

You can change the settings for this unit. (B 16)

When “Sound” is selected

You can select sound quality settings (B 12, EQ (Equaliser)).

Other selectable items

The items that are displayed will vary depending on the media and

source.

When a disc is loaded or an USB device is connected, you can also

access playback or menus from the START menu.

e.g. [DVD-V]

When the on-screen control panel appears

e.g. [DVD-V] (when “Playback Disc” is selected from the START menu)

You can operate the playback with the indicated controls.



Confirm the audio connection to the SCART (AV), AUX, HDMI AV OUT or

DIGITAL AUDIO IN OPTICAL terminal on the main unit when you select the

corresponding sources (B 8). Reduce the volume on the TV to its minimum,

and then adjust the volume of the main unit.

Listening to the radio

Presetting stations automatically

Press [RADIO]4 to select “FM”.

Press [MENU]C to select “LOWEST” or “CURRENT”.

LOWEST:

To begin auto preset with the lowest frequency (FM 87.50).

CURRENT:

To begin auto preset with the current frequency.

§ To change the frequency, refer to “Manual tuning and presetting”.

Press and hold [OK]8.

Release the button when “FM AUTO” is displayed.

The tuner starts to preset all the stations it can receive into the

channels in ascending order.

Listening to a preset channel

Press [RADIO]4 to select “FM”.

Press the numbered buttons to select the channel.

≥ To select a 2-digit number

e.g. 12: [S10]2 B [1] B [2]

Alternatively, press [X, W]@.

Manual tuning and presetting

RDS broadcasting

PTY displays

NEWS VARIED FINANCE COUNTRY

AFFAIRS POP M CHILDREN NATIONAL

INFO ROCK M SOCIAL A OLDIES

SPORT M.O.R. M

RELIGION FOLK M

EDUCATE LIGHT M PHONE IN DOCUMENT

DRAMA CLASSICS TRAVEL TEST

CULTURE OTHER M LEISURE ALARM

SCIENCE WEATHER JAZZ

Using the START menu

Press [START]B to show the START menu.

≥ When using VIERA Link “HDAVI Control”, the TV also turns on

when the START menu is displayed.

Press [3, 4]8 to select an item and press [OK]8.

≥ To exit, press [START]B.

Press [3, 4, 2, 1]8 to make the setting and press

[OK]8.

Selecting the source using the remote control

Press To select

[DVD]4 DVD/CD

[RADIO]4 FM (B left)

[EXT-IN]4 Each time you press the button:

AV:

AUX:

ARC:

D-IN:

USB:

For audio input through the SCART (AV) terminal.

For audio input through the AUX terminal.

For audio input through the HDMI AV OUT terminal.

For audio input through the DIGITAL AUDIO IN

OPTICAL terminal. (B 11)

(B 16)

e.g.

Input Selection

Setup

Sound

DVD/CD Home Cinema

Input Selection

Setup

Playback Disc

TOP MENU(DVD)

MENU(DVD)

Playback/menu access

SC-XH175 EP_RQT9597-R_eng.book Page 10 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting StartedPlaying DiscsOther OperationsReference

ENGLISH

Preparation

≥ Make sure that there is an audio connection between this unit and the

TV or other device. (B 8)

≥ Turn on the TV or/and other device.

Press [EXT-IN]4 to choose the source that is used to

connect this unit to the TV or other device.

≥ To change the surround sound effects and sound mode, refer to

“Enjoying sound effects from all speakers” (B right).

≥ If your Panasonic TV is VIERA Link compatible, refer to “Linked

operations with the TV” (B 15) for other related functions.

Select to suit the type of audio from the DIGITAL AUDIO IN OPTICAL and

HDMI AV OUT terminal on the main unit.

≥ Underlined items are the factory presets.

§ Only when “D-IN” is selected.

Be sure to select the device’s (STB, etc.) input channel on the TV when

making the setting.

The device must be connected to the Panasonic TV via an HDMI cable

and to this unit with an optical digital audio cable.

≥If the device’s (STB, etc.) input channel on the TV is changed or if you

want to change the device allocated for the linked operations, select

the “STB” mode to “OFF” in step 3 above and then select “SET”

again.

≥This function will not operate if “DIGITAL IN” is selected in “TV Audio”

(B 17).

≥ The following sound effects may not be available or may have no effect

with some sources.

≥ You may experience a reduction in sound quality when these sound

effects are used with some sources. If this occurs, turn the sound effects

off.



When changing the surround sound effect, Whisper-mode Surround or the

sound modes, the setting is displayed on the TV screen if “DVD/CD” or “USB” is

the selected source during video playback.

For “Front layout (Alternative)”

mode

STANDARD:

Stereo source is output as 2.1-channel audio.

When playing surround sources, you can enjoy 5.1-channel

surround-like effect even with all the speakers at the front.

STEREO:

You can play any source in stereo. Surround sound effect is

unavailable.

A.SRD (Advanced Surround):

You can enjoy surround effect with any audio source.

When the signal is Dolby Digital, “/DOLBY DIGITAL” will also be

displayed.

§ Selected mode in “Speaker layout” (B 9, Easy setup).

Listening to the TV or other device’s

audio from this unit’s speakers

Making settings for digital audio input

Available settings

Mode Setting

DUAL: (Only works with Dolby Dual Mono)

– MAIN+SAP

(stereo audio)

– MAIN

– SAP

“SAP” = Secondary Audio Program

≥ Set PCM FIX mode to “OFF” to listen to the “MAIN” or

“SAP” audio.

DRC:

(Dynamic

Range

Compression)

– ON

Adjust for clarity even when the volume is low by

compressing the range of the lowest sound level and

the highest sound level. Convenient for late night

viewing. (Only works with Dolby Digital)

– OFF

The full dynamic range of the signal is reproduced.

PCM FIX: – ON

Select when receiving only PCM signals.

– OFF

Select when receiving Dolby Digital and PCM signals.

≥ When receiving true 5.1-channel surround sound,

select “OFF”.

STB

(CABLE/SAT

AUDIO)

– SET

Select when setting the main unit to switch to

“D-IN” when the input channel of an HDMI connected

device (STB, etc.) is selected on the TV (B 15,

Setting the audio link with the STB).

– OFF

Select to cancel this setting.

Press [EXT-IN]4 several times to select “D-IN” or

“ARC”.

Press [PLAY MODE]9 and then [3, 4]8 to select the

mode.

While the selected mode is displayed, press [2, 1]8 to

select the desired setting.

Enjoying sound effects from all

speakers

Enjoying surround sound effects

Press [SURROUND];.

Each time you press the button:

For “Surround layout (Recommended)”

mode

STANDARD:

Sound is output as it was recorded/encoded. Speaker output varies

depending on the source.

MULTI-CH:

You can enjoy sound from the front speakers, as well as the surround

speakers and center speaker even when playing stereo sources.

MANUAL: (B below)

While “MANUAL” is displayed, press [2, 1]8 to select

other surround modes.

Each time you press [2, 1]8:

DOLBY PLII MOVIE

Suitable for movies, or videos recorded in Dolby Surround.

DOLBY PLII MUSIC

Adds 5.1-channel effects to stereo sources.

S.SRD (Super Surround)

You can enjoy surround effect with stereo sources.

STEREO

Sound will only be output to the front speakers and the subwoofer from

any source.

Recommended modes to enjoy TV audio or stereo

sources from all speakers:

“MULTI-CH”, “DOLBY PL

MOVIE”, “DOLBY PL

MUSIC” or “S.SRD”

SC-XH175 EP_RQT9597-R_eng.book Page 11 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

You can enhance the audio effect for low volume 5.1-channel sound.

(Convenient for late night viewing.)

Press and hold [–W.SRD]: to show the current setting.

While the current setting is displayed, press [–W.SRD]: to change the

setting.

ON ,------. OFF

Only when “Surround layout (Recommended)” mode is selected in

“Speaker layout” (B 9, Easy setup)

(Effective when playing 5.1-channel sound or when DOLBY PLII/“S.SRD”

(B 11) is selected.)

For “Surround layout (Recommended)”

mode:

Front speaker balance

For “Front layout (Alternative)”

mode:

Front and surround speaker balance

§ Selected mode in “Speaker layout” (B 9, Easy setup).

Preparation

To display the picture, turn on your TV and change its video input mode

(e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the connection to this unit.



≥ When you press [< OPEN/CLOSE]2 to close the disc tray, this unit

automatically starts playing the disc in the tray.

[MP3] [JPEG] [DivX]

– Only the contents in the current group will be played.

– If there are MP3, JPEG and DivX contents in the current group, only one

content type will be played. (Priority: MP3 # JPEG # DivX)

You can select an item of your desired content type to start play.

(B 13, Using navigation menu)

≥ DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED.

Press [∫ STOP]5 when you finish to preserve the unit’s motor and your TV

screen.

≥ Total title number may not be displayed properly on iR/iRW.

Selecting sound mode

Press [SOUND]: to select a sound mode.

Each time you press the button:

EQ: Equaliser

SUBW LVL: Subwoofer Level

C.FOCUS: Center Focus (Only when “Surround layout

(Recommended)” mode is selected in “Speaker

layout” (B 9, Easy setup).)

While the selected mode is displayed, press [2, 1]8 to

make the settings.

Refer to the following for setting details of each sound effect.

EQ (Equaliser)

You can select sound quality settings.

Each time you press [2, 1]8:

FLAT: Cancel (no effect is added).

HEAVY: Adds punch to rock.

CLEAR: Clarifies higher sounds.

SOFT: For background music.

SUBW LVL (Subwoofer level)

You can adjust the amount of bass. The unit automatically selects

the most suitable setting according to the type of playback

source.

LEVEL 1 ,# LEVEL 2 ,# LEVEL 3 ,# LEVEL 4

^---------------------------------------------------------------------------J

≥ The setting you make is retained and recalled every time you

play the same type of source.

C.FOCUS (Center Focus)

(Effective when playing audio containing the center channel

sound or when DOLBY PLII (B 11) is selected.)

You can make the sound of the center speaker seem like it is

coming from within the TV.

ON ,------. OFF

Whisper-mode Surround

Adjusting the speaker level during playback

Press [CH SELECT]F to select the speaker.

Each time you press the button:

e.g. L# C# R# RS# LS# SW

^---------------------------------------------}

≥ You can adjust SW (Subwoofer) only if the disc includes a

subwoofer channel.

≥ When “S” appears, only the surround speaker channel can be

adjusted. Both surround speaker levels will be adjusted at the same

time.

While “C”, “RS”, “LS”, “SW” or “S” is selected

Press [3]8 (increase) or [4]8 (decrease) to adjust the

speaker level for each speaker.

C, RS, LS, SW, S: `6dB to i6dB

(L, R: Only the balance is adjustable.) (B below)

Adjusting the speaker balance during playback

Press [CH SELECT]F to select “L” or “R”.

While “L” or “R” is selected

Press [2, 1]8 to adjust the speaker balance.

Basic play

Press [Í]1 to turn on the unit.

Press [DVD]4 to select “DVD/CD”.

Press [< OPEN/CLOSE]2 to open the disc tray.

Load the disc.

≥ Load double-sided discs so the label for the

side you want to play is facing up.

Press [1 PLAY]5 to start play.

≥ Press [r, VOL, s]= to adjust the volume.

Basic controls

Stop: [∫ STOP]5

The position is memorised while “RESUME” is on the main unit’s display.

[DVD-V] [VCD] [CD] [MP3] [DivX] This unit can memorise the resume

position for the last 5 discs.

≥ Press [1 PLAY]5 to resume.

≥ Press [∫ STOP]5 again to clear the position.

Pause: [; PAUSE]5

≥ Press [1 PLAY]5 to restart play.

Skip: [SKIP:,SKIP9]5

Search: [SEARCH6, SEARCH5]5 (during play)

Slow-motion: [SEARCH6, SEARCH5]5 (during pause)

≥ Search: Up to 4 steps

Slow-motion: Up to 3 steps

≥ Press [1 PLAY]5 to start normal play.

≥ [VCD] [DivX] Slow-motion: Forward direction only.

Frame-by-frame (during pause)

[DVD-V] : [2;, ;1]8

[DVD-V] [VCD] [DivX] : [; PAUSE]

5 (forward direction only)

On-screen item select: [3, 4, 2, 1, OK]8

[3, 4, 2, 1]8: Select

[OK]8: Confirm

Enter number: Numbered buttons

[DVD-V] [VCD] [CD]

e.g. To select 12: [S10]2 B [1] B [2]

Label facing up

SC-XH175 EP_RQT9597-R_eng.book Page 12 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting StartedPlaying DiscsOther OperationsReference

ENGLISH

You can select to play from your desired item while the navigation menu

screen is displayed.

e.g. Data disc

Play starts from the selected content.

[MP3] [JPEG] [DivX]

≥ To return to the previous folder, press [RETURN]D. You can also do

this by selecting “ ” in the menu.

≥ Maximum: 16 characters for file/folder name.

≥ Only the contents in the current group will be played.

≥ If there are MP3, JPEG and DivX contents in the current group, play will

be based on the selected content type.

∫ Rotating a picture

Preparation

To clear the selected program

1 Press [1]8 and then press [3, 4]8 to select the program.

2 Press [CANCEL]3.

To clear the whole program

Press [1]8 several times to select “Clear All”, and then press [OK]8.

The whole program is also cleared when the disc tray is opened, the unit

is turned off or another source is selected.

[CD] All tracks will be played in random order.

Press [1 PLAY]5 to start play.

[MP3] [JPEG] [DivX] The MP3/JPEG/DivX contents of the selected group

will be played in random order.

[DVD-V] Show a disc top menu: [TOP MENU]7

[DVD-V] Show a disc menu: [MENU]C

Return to previous screen: [RETURN]D

[VCD] (with playback control)

Show a disc menu: [RETURN]D

Turn PBC function on/off: [MENU]C

Main unit display: [FL DISPLAY]E

[DVD-V] [MP3] [DivX]

Time display

,-. Information display

[JPEG]

SLIDE

,-.Contents number

Playing from the selected item

Using navigation menu

[CD] [MP3] [JPEG] [DivX]

Press [3, 4]8 to select an item and press [OK]8.

≥ Press [2, 1]8 to skip page by page.

Selecting the picture in Thumbnail menu

[JPEG]

While the picture is displayed, press [TOP MENU]7 to

show the thumbnail menu.

e.g.

Press [3, 4, 2, 1]8 to select a picture and press

[OK]8.

≥ Press [SKIP:,SKIP9]5 to skip page by page.

While a picture is displayed, press [3, 4, 2, 1]8 to rotate the

picture.

/ .../Underwater.MP3

1/3

Perfume

Underwater

Fantasy planet

Starpersons1

00:02:40

Group (Folder):

Content (File/Track):

: MP3/CD-D

: JPEG

: DivX

Elapsed time

Other modes of play

Program and Random play

[CD] [MP3] [JPEG] [DivX]

While stopped, press [PLAY MODE]9 to select the play

mode.

Each time you press the button:

[CD] [MP3] Music Program menu

[JPEG] Picture Program menu

[DivX] Video Program menu

RND (Random) menu

Exit program and random menus

Program play (up to 30 items)

Press [3, 4]8 to select an item and press [OK]8.

e.g. [MP3]

≥ When a content is selected, it will be programmed.

≥ Repeat this step to program other items.

≥ [MP3] [JPEG] [DivX] To return to the previous folder, press

[RETURN]D. You can also do this by selecting “ ” in the

menu.

Press [1 PLAY]5 to start play.

Random play

Press [3, 4]8 to select the desired group and press

[OK]8.

e.g. [MP3]

≥ To return to the previous folder, press [RETURN]D. You can also do

this by selecting “ ” in the menu.

Press [3, 4]8 to select the desired content

and press

[OK]8.

Play starts from the selected content.

§ If there are MP3, JPEG and DivX contents, random play will be

based on the selected content type.

Music Program

Track 1

Track 2

Track 3

Track 4

/ .../Track 1.MP3

RND

1/10

Track 1

Track 2

Track 3

Track 4

SC-XH175 EP_RQT9597-R_eng.book Page 13 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

This works only when the elapsed play time can be displayed. It also

works with all JPEG content.

Items shown differ depending on the type of disc and playback mode.



Random mode will be cleared when you change the repeat mode.



This does not work during HD JPEG playback (B 17, HD JPEG Mode [JPEG])

Repeat play

During play, press and hold [–REPEAT]9, to show the

repeat mode.

While the repeat mode is displayed, press [–REPEAT]9 to select the

item to be repeated.

e.g. [DVD-V]

`Chapter ---. `Title ---. `Off

^-------------------------------------------_------b

To cancel, select “Off”.

Using on-screen menus

Press [FUNCTIONS]6 to show the on-screen menu.

Each time you press the button:

Menu 1 (Disc)

Menu 2 (Video)

Menu 3 (Audio)

Exit

Press [3, 4, 2, 1]8 to select the item and press

[OK]8.

Press [3, 4]8 to make the settings and press [OK]8.

Items shown will vary depending on the type of disc.

Menu 1 (Disc)

Track Search, Title Search, Content Search, Chapter

To start from a specific item

e.g. [DVD-V]: T2 C5

To select 12: [S10]2 B [1] B [2] B [OK]8

Audio

[DVD-V] [DivX] (with multiple soundtracks)

To select audio soundtrack

[VCD]

To select “L”, “R”, “L+R” or “L R”

Actual operations depend on the disc. Read the disc’s instructions for

details.

Signal type/data

LPCM/ D/DTS

/MP3/MPEG: Signal type

§ During playback of DTS source, there will be no sound from the

speakers.

≥ [DivX] It may take some time for play to start if you change the audio on

a DivX video disc.

1/5

Off O

Title Search

Current item

Item name

e.g. [DVD-V] Menu 1 (Disc)

Off O

Chapter Search

1/5

Current setting

e.g. [DVD-V] Menu 1 (Disc)

Play Speed

[DVD-V]

To change play speed

–from “k0.6” to “k1.4” (in 0.1-unit steps)

≥ Press [1 PLAY]5 to return to normal play.

≥ After you change the speed

– Dolby Pro Logic II has no effect.

– Audio output switches to 2-channel stereo.

– Sampling frequency of 96 kHz is converted to 48 kHz.

≥ This function may not work depending on the disc’s recording.

Repeat Mode

(B left, Repeat play)

A-B Repeat (To repeat a specified section)

Except [JPEG] [DivX]

Press [OK]8 at the starting and ending points.

≥ Select “Off” to cancel.

Subtitle

[DVD-V] (with multiple subtitles)

To select subtitle language

≥ On iR/iRW, a subtitle number may be shown for subtitles that are

not displayed.

[DivX] (B 18, Displaying DivX subtitles text)

Angle

[DVD-V] (with multiple angles)

To select a video angle

Menu 2 (Video)

Transfer Mode

To select the method of conversion for video output to suit the type

of material

Auto, Video

≥ When the content is distorted, select “Video”.

≥ This may have no effect with some sources.

Zoom

To select zoom

Normal, 1, 2, 3

Menu 3 (Audio)

Dialogue Enhancer

To make the dialogue in movies easier to hear

[DVD-V] [DivX] (Dolby Digital, 3-channel or higher, with the dialogue

recorded in the center channel)

Off, On

SC-XH175 EP_RQT9597-R_eng.book Page 14 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting StartedPlaying DiscsOther OperationsReference

ENGLISH

Preparation

≥ Confirm that the HDMI connection has been made (B 8).

1 Set “VIERA Link” to “On” (B 17).

(The default setting is “On”.)

2 Set the “HDAVI Control” operations on the connected equipment

(e.g., TV).

3 Turn on all “HDAVI Control” compatible equipment and select this unit’s

input channel on the connected TV so that the “HDAVI Control”

function will work properly.

Whenever the connection or settings are changed, repeat this

procedure and reconfirm the points in “Setting the audio link”

(B below).

∫ Setting the audio link with the TV

Select “AV”, “AUX”, “ARC”

§1

or “DIGITAL IN” for TV audio link.

Refer to TV audio setting in Easy setup (B 9) or “TV Audio” in HDMI

menu (B 17).

Confirm the TV audio connection to the SCART (AV) terminal (for “AV”),

AUX terminal (for “AUX”), HDMI AV OUT terminal (for “ARC”

§1

) or

DIGITAL AUDIO IN OPTICAL terminal (for “DIGITAL IN”) on the main unit

(B 8).

∫ Setting the audio link with the STB

Select “D-IN” for STB audio link.

Refer to STB setting in “Making settings for digital audio input” (B 11).

Confirm the STB audio connection to the DIGITAL AUDIO IN OPTICAL

terminal (for “D-IN”) on the main unit (B 8).



≥ VIERA Link “HDAVI Control”, based on the control functions provided by

HDMI which is an industry standard known as HDMI CEC (Consumer

Electronics Control), is a unique function that we have developed and added.

As such, its operation with other manufacturers’ equipment that supports

HDMI CEC cannot be guaranteed.

≥ This unit supports “HDAVI Control 5” function.

“HDAVI Control 5” is the newest standard (current as of November, 2011) for

Panasonic’s HDAVI Control compatible equipment. This standard is

compatible with Panasonic’s conventional HDAVI equipment.

≥ Please refer to individual manuals for other manufacturers’ equipment

supporting VIERA Link function.

(For “HDAVI Control 3 or later”)

This function automatically provides synchronised audio and video

output. (This works only when the source is “DVD/CD”, “USB”, “AV”

§2

“AUX”

§2

, “ARC”

§1, 2

or “D-IN”

§2, 3

≥ When using “DVD/CD” or “USB” as the source, set “Time Delay” in

Video menu to “0ms/Auto” (B 17).

When the following operations are performed, the TV will automatically

switch the input channel and display the corresponding action.

Additionally when the TV is off, the TV will automatically turn on:

– When play starts on the unit

– When an action that uses the display screen is performed (e.g., START

menu)

All connected equipment compatible with “HDAVI Control”, including this

unit, automatically turn off when you switch the TV off.

To continue audio playback even when the TV is turned off, select “Video”

(B 17, “Power Off Link” in HDMI menu).



When you press [Í]1, only this unit turns off. Other connected equipment

compatible with VIERA Link “HDAVI Control” stays on.

For details, refer also to the operating instructions for your TV.

You can select whether audio will output from this unit’s speakers or the

TV speakers by using the TV menu settings. For details, refer to the

operating instructions for your TV.

Home Cinema

This unit’s speakers are active.

≥ When you turn on this unit, this unit’s speakers will be automatically

activated.

≥ When this unit is in standby mode, changing the TV speakers to this

unit’s speakers in the TV menu will automatically turn this unit on and

select “AV”

§2

“AUX”

§2

, “ARC”

§1, 2

or “D-IN”

§2, 3

as the source.

≥ The TV speakers are automatically muted.

≥ You can control the volume setting using the volume or mute button on

the TV’s remote control. (The volume level is displayed on the main

unit’s display.)

≥ To cancel muting, you can also use this unit’s remote control (B 4).

≥ If you turn off this unit, TV speakers will be automatically activated.

TV speakers are active.

≥ The volume of this unit is set to “0”.

– This function works only when “DVD/CD”, “USB”, “AV”

§2

, “AUX”

§2

“ARC”

§1, 2

or “D-IN”

§2, 3

is selected as the source on this unit.

≥ Audio output is 2-channel audio.



When switching between this unit speakers and TV speakers, the TV screen

may go blank for several seconds.

Linked operations with the TV

(VIERA Link “HDAVI Control

”)

What is VIERA Link “HDAVI Control”?

VIERA Link “HDAVI Control” is a convenient function that offers linked

operations of this unit, and a Panasonic TV (VIERA) under “HDAVI

Control”. You can use this function by connecting the equipment with

the HDMI cable. See the operating instructions for connected

equipment for operational details.

Setting the audio link

Auto lip-sync

Auto input switching

(Power on link)

≥ When you switch the TV input to TV tuner mode or the STB input

channel, this unit will automatically switch to “AV”

§2

, “AUX”

§2

, “ARC”

§1, 2

or “D-IN”

§2, 3

≥ When this unit is in “DVD/CD” mode, the TV will automatically switch its

input mode for this unit.

≥ The TV will automatically switch to TV tuner mode when:

– you press [EXIT]A.

§4, 5

– you press [RETURN]D to exit the START menu.

§4, 5

– you select “AV”

§2

“

AUX”

§2

, “ARC”

§1, 2

or “DIGITAL IN”

§2

from the

START menu.

– playback stops ([DVD-V] [VCD]) or when this unit turns off.

§5

Power off link

Speaker selection

§1

The selection works only when using an ARC compatible TV.

§2 “AV”, “AUX”, “ARC” or “D-IN” (DIGITAL IN) works depending on the

TV audio setting (B left, Setting the audio link with the TV).

§3

“D-IN” (DIGITAL IN) works depending on the STB audio setting

(B left, Setting the audio link with the STB).

§4 This does not work during playback or resume mode when

“DVD/CD” or “USB” is selected as the source.

§5 Only after the TV automatically switched to the HDMI input mode for

this unit.

SC-XH175 EP_RQT9597-R_eng.book Page 15 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

(For “HDAVI Control 2 or later”)

You can control the playback menus of this unit with the TV’s remote

control. When operating the TV’s remote control, refer to the below

illustration for operation buttons.



≥ Depending on the menu, some button operations cannot be performed from

the TV’s remote control.

≥ You cannot input numbers with the numbered buttons on the TV’s remote

control ([0] to [9]). Use this unit’s remote control to select the play list etc.

You can connect and play tracks or files from USB mass storage class

devices (B 19).

Devices which are defined as USB mass storage class:

– USB devices that support bulk only transfer.

Preparation

≥ Before connecting any USB mass storage device to the unit, ensure

that the data stored therein has been backed up.

≥ It is not recommended to use a USB extension cable. The USB device

connected using the cable will not be recognised by this unit.

≥ To playback a selected item, press [∫ STOP]5 and refer to “Playing

from the selected item” (B 13).

≥ For other operating functions, they are similar to those described in

“Playing Discs” (B 12 to 14).



≥ Maximum: 259 folders (excluding Root folder), 2600 files, 16 characters for

file/folder name.

≥ Only one memory card will be selected when connecting a multiport USB

card reader. Typically the first memory card inserted.

≥ To return to the previous screen, press [RETURN]D.

≥ To exit the screen, press [START]B.

≥ The settings remain intact even if you switch the unit to standby.

≥ Underlined items are the factory settings in the following menus.

Audio

Choose the audio language.

Subtitle

Choose the subtitle language.

DVD Menu

Choose the language for disc menus.

§ Some discs start in a certain language despite any changes you

make here.

When the selected language is not available on the disc, the default

language is played. There are discs where you can only switch the

language from the menu screen (

B 13).

Subtitle Text [DivX]

Select a suitable item according to the language used for DivX subtitles

text (B 18).

Easy control only with VIERA remote control

1 Select this unit’s operation menu by using the TV menu settings.

(For details, refer to the operating instructions for your TV.)

The START menu will be shown.

e.g. [DVD-V]

≥ The START menu can also be shown by using a button on the TV’s

remote control (e.g. [OPTION]).

– When “DVD/CD” or “USB” is selected as the source, the TV’s

remote control works only during stop mode.

2 Select the desired item on the START menu (B 10).

When the on-screen control panel appears

e.g. [DVD-V] (when “Playback Disc” is selected from the START menu.)

You can operate the playback with the indicated controls.

≥ The on-screen control panel can also be shown by using a button on the

TV’s remote control (e.g. [OPTION]).

– This works only during “DVD/CD” or “USB” playback and resume

modes.

Playing from an USB device

Connect the USB device (not supplied) to the USB port

( 6).

When you press [EXT-IN]4 to select “USB”, this unit

automatically starts playing the contents in the USB

device.

DVD/CD Home Cinema

Input Selection

Setup

Playback Disc

TOP MENU(DVD)

MENU(DVD)

Playback/menu access

Changing the player settings

Press [DVD]4 to select “DVD/CD”.

Press [START]B to show the START menu.

Press [3, 4]8 to select “Setup” and press [OK]8.

Press [3, 4]8 to select menu and press [OK]8.

Press [3, 4]8 to select the item and press [OK]8.

Press [3, 4]8 to make the settings and press [OK]8.

Language menu

Display

Choose the language for the on-screen messages.

≥ English

≥ Français ≥Español ≥ Deutsch

≥ Русский ≥ Magyar ≥ Polski ≥ Çesky

≥ English

≥ French ≥ Spanish ≥German

≥ Russian ≥ Hungarian ≥ Polish ≥ Czech

≥ Auto

≥ English ≥ French ≥ Spanish

≥ German ≥ Russian ≥ Hungarian ≥ Polish

≥ Czech ≥ Off

≥ English

≥ French ≥ Spanish ≥German

≥ Russian ≥ Hungarian ≥ Polish ≥ Czech

≥ Latin1 ≥ Latin2

≥ Cyrillic ≥ Turkish

Video menu

TV Aspect

Choose the setting to suit your TV.

≥ 16:9

: Widescreen TV (16:9)

≥ 4:3 Pan&Scan: Regular aspect TV (4:3)

The sides of the widescreen picture are cut off so it

fills the screen (unless prohibited by the disc).

≥ 4:3 Letterbox: Regular aspect TV (4:3)

Widescreen picture is shown in the letterbox style.

Setup

Display

Audio

Subtitle

DVD Menu

Subtitle Text

: English

: Auto

: English

: Latin2

Language

Video

Audio

HDMI

Others

Set

RETURN

Item

Current setting

SC-XH175 EP_RQT9597-R_eng.book Page 16 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting StartedPlaying DiscsOther OperationsReference

ENGLISH

Video Out-SCART

Choose the video signal format to be output from the SCART (AV)

terminal.

≥ Video

≥ S-Video

≥ RGB 1: (Only when connected to a RGB compatible TV)

If you always would like to view the picture from the unit in RGB signal,

select this mode. The TV screen will automatically switch to display the

picture from the unit when the unit is turned on.

≥ RGB 2: (Only when connected to a RGB compatible TV)

When in TV tuner mode, if the selector is set to “DVD/CD”, the TV

screen will automatically switch to display the picture from the unit only

during disc playback ([DVD-V] [VCD]) or when viewing on-screen menu of

DVD/CD.

The TV picture will be displayed when the selector is set to “AV”. With

other selectors, the picture from this unit will be displayed.

Select to suit the type of equipment you connected to the HDMI AV OUT

terminal.

Select “Bitstream” when the equipment can decode the bitstream (digital

form of 5.1-channel data). Otherwise, select “PCM”.

(If the bitstream is output to the equipment without a decoder, high levels

of noise can be output and may damage your speakers and hearing.)

Digital Output

When audio output is from HDMI AV OUT terminal, and the connected

equipment does not support the item selected, the actual output will

depend on the performance of this connected equipment.

Time Delay

When connected with a Plasma display, adjust if you notice the audio is

out of sync with the video.

≥ 0ms/Auto

≥ 20ms ≥ 40ms ≥ 60ms

≥ 80ms ≥ 100ms

When using VIERA Link “HDAVI Control” with “HDAVI Control 3 or later”

compatible TV (B 15), select “0ms/Auto”.

Audio and video will automatically be set in sync.

TV System

Choose the appropriate output source when connecting to a TV

(B 19, Video systems).

≥ NTSC: When connected to an NTSC TV.

≥ PAL

: When connected to a PAL TV.

≥ Auto: Selects the original output source when playing PAL or NTSC

discs.

Video Resolution

This works only when the HDMI connection is being used.

Select suitable picture quality with your TV.

(Video recordings will be converted to, and output as, high-definition

video.)

≥ Auto

≥ 480i/576i ≥ 480p/576p ≥ 720p

≥ 1080i ≥ 1080p

Ensure that your TV can support the resolution that you choose.

If a message screen appears, confirm your selection by pressing

[2, 1]8 to select “Yes” and press [OK]8. If the picture is distorted, wait

for 15 seconds or press [2, 1]8 to select “No”. To accept the setting,

select “Yes” again.

HD JPEG Mode [JPEG]

(This works only when using HDMI connection with “Video Resolution”

(B above) set to “Auto”, “720p”, “1080i” or “1080p”.)

≥ On

: HD JPEG playback is available. (JPEG images will be displayed in

original resolution.)

≥ Off

During HD JPEG playback, there will be no on-screen menus (B 14) and

on-screen displays.

Audio menu

≥ Bitstream ≥ PCM

Dynamic Range

≥ On: Adjusts for clarity even when the volume is low. Convenient for

late night viewing. (Only works with Dolby Digital)

≥ Off

: The full dynamic range of the signal is reproduced.

Speaker Settings

Select the delay time of the speakers.

(Effective only when “Surround layout (Recommended)” mode is selected

in “Speaker layout” (B 9, Easy setup).)

(Center and surround speakers only)

For optimum listening with 5.1-channel sound, all the speakers, except for

the subwoofer, should be the same distance from the seating position.

If you have to place the center or surround speakers closer to the seating

position, adjust the delay time to make up for the difference.

If either distance a or b is less than c, find the difference in the table

and change to the recommended setting.

a Center speaker b Surround speaker

Difference (Approx.) Setting Difference (Approx.) Setting

30 cm 1ms 150 cm 5ms

60 cm 2ms 300 cm 10ms

90 cm 3ms 450 cm 15ms

120 cm 4ms

150 cm 5ms

≥ C Delay (Center Delay):

0ms

, 1ms, 2ms, 3ms, 4ms, 5ms

Select the delay time for your center speaker.

≥ LS/RS Delay (Left Surround/Right Surround Delay):

0ms

, 5ms, 10ms, 15ms

Select the delay time for your surround speakers.

≥ Test Tone:

Use the test tone to listen to the speaker output to confirm speaker

connections.

Test tone will be output to each channel in the following order.

Left, Center, Right, Surround Right, Surround Left, Subwoofer

To stop the test tone, press [RETURN]D.

HDMI menu

VIERA Link

≥ On: The VIERA Link “HDAVI Control” function is available (B 15).

≥ Off

Audio Out

≥ On: When audio output is from the HDMI AV OUT terminal.

(Depending on the capabilities of the connected equipment,

audio output may differ from the audio settings of the main unit.)

≥ Off

: When audio output is not from the HDMI AV OUT terminal. (The

audio is output using the settings of the main unit.)

Power Off Link

Select the desired power off link setting of this unit for VIERA Link

operation (B 15). (This works depending on the settings of the connected

VIERA Link “HDAVI Control” compatible equipment.)

≥ Video/Audio

: When the TV is turned off, this unit will turn off

automatically.

≥ Video: When the TV is turned off, this unit will turn off except during the

following conditions:

– audio playback ([CD] [MP3])

– radio mode

– “AV”, “AUX”, “ARC” or “D-IN” mode (non-selected TV audio

setting for

VIERA Link

)

TV Audio

Select the TV audio input to work with the VIERA Link operations (B 15).

≥ AUX

≥ ARC

≥ DIGITAL IN

≥ AV











Actual speaker position

Ideal speaker position

Primary listening

distance

Approximate room dimensions

Circle of constant primary listening distance

SC-XH175 EP_RQT9597-R_eng.book Page 17 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

Ratings

Set a rating level to limit DVD-Video play.

Setting ratings (When level 8 is selected)

≥ 1 to 7

≥ 8 No Limit

When you select your ratings level, a password screen is shown.

The default password is “0000”.

Enter the 4-digit password with the numbered buttons, and press [OK]8.

You can change the default password (B below)

Do not forget your password.

A message screen will be shown if a DVD-Video disc exceeding the rating

level is inserted in the unit.

Follow the on-screen instructions.

Set Password

Change the password for “Ratings”.

When you change the password for the first time:

The default password is “0000”.

Follow the on-screen instructions.

Restore Default Settings

This returns all values in the Setup menu to the default settings except the

password and ratings level.

Press [2, 1]8 to select “Yes” and press [OK]8.

Turn the unit off and on again.

ABOUT DIVX VIDEO:

DivX

is a digital video format created by DivX, LLC, a subsidiary of Rovi

Corporation. This is an official DivX Certified

device that plays DivX

video.

Visit divx.com for more information and software tools to convert your files

into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND:

This DivX Certified

device must be registered in order to play purchased

DivX Video-on-Demand (VOD) movies.

To obtain your registration code, locate the DivX VOD section in your

device setup menu.

Go to vod.divx.com for more information on how to complete your

registration.

≥ After playing DivX VOD content for first time, “DivX Registration” is not

selectable until this unit is deregistered.

≥ If you purchase DivX VOD content using a registration code different

from this unit’s code, you will not be able to play this content.

Regarding DivX content that can only be played a set

number of times

Some DivX VOD contents can only be played a set number of times.

When you play this content, the number of times already played and

initially playable number of times is displayed.

≥ The remaining number of plays decreases each time a programme is

played. However, when playing from the point where play was

previously stopped, the remaining number of plays does not decrease

due to the resume play function.

You can display subtitles text on a DivX video disc with this unit.

This function has no relation to the subtitles specified in the DivX standard

specifications and has no clear standard.

Set “Subtitle” in Menu 1 (Disc) (B 14).

DivX video files that do not display “On” do not contain subtitles text.

Subtitles text cannot be displayed.

Types of subtitles text file that can be displayed

Subtitles text that satisfy the following conditions can be displayed on this

unit.

≥ File format: MicroDVD, SubRip, or TMPlayer

≥ File extension: “.SRT”, “.srt”, “.SUB”, “.sub”, “.TXT”, or “.txt”

≥ File name: No more than 16 characters excluding the file extension

≥ The DivX video file and subtitles text file are inside the same folder, and

the file names are the same except for the file extensions.

≥ If there are more than one subtitles text files inside the same folder, they

are displayed in the following order of priority: “.srt”, “.sub”, “.txt”.



≥ Depending on the methods used to create the file or the state of the

recording, only parts of the subtitles may be displayed, or the subtitles may

not be displayed at all.

≥ The subtitles text cannot be displayed during menu display or when

operations such as search are being performed.

≥ If the subtitles text are not displayed correctly, try changing the subtitle text

settings (B 16).

Others menu

DivX Registration [DivX]

Display the unit’s registration code.

You need this registration code to purchase and play DivX Video-on-

Demand (VOD) content (B right).

DivX Deregistration [DivX]

Display the unit’s deregistration code.

You need this deregistration code to cancel this unit’s registration

(B right).

This setting is only selectable after playing DivX VOD content for the first

time.

Slide Show Time

Set the speed of the slideshow.

≥ 3 Seconds

≥ 5 Seconds ≥ 10 Seconds ≥15 Seconds

Easy setup

You can execute basic settings to optimise your home theater system.

(B 9)

FL Dimmer

Change the brightness of the unit’s display.

≥ Bright

≥ Dim: The display is dimmed.

≥ Auto: The display is dimmed, but brightens when you perform some

operations.

Screen Saver

This is to prevent burn marks on the TV screen.

≥ Off

≥ Wait 5 min

: If there is no operation for 5 minutes, the screen saver will

be shown. The TV screen will resume when you perform

some operations. (This does not work during playback.)

DivX information

Display the unit’s registration code

(B left, “DivX Registration” in Others menu)

Cancel the unit’s registration

Select “DivX Deregistration” (B left) and follow the on-screen instructions.

Use the deregistration code to cancel the registration in

http://vod.divx.com.

Displaying DivX subtitles text

You must register your device to play

DivX® protected videos.

Registration code:XXXXXXXXXX

10 alphanumeric characters

SC-XH175 EP_RQT9597-R_eng.book Page 18 Wednesday, December 14, 2011 9:38 AM

RQT9597

Getting StartedPlaying DiscsOther OperationsReference

ENGLISH

Commercial discs

Recorded discs and USB devices

≥ Before playback, finalise the disc on the device it was recorded on.

≥ It may not be possible to play all the above-mentioned medias in some

cases due to the type of media, the condition of the recording, the

recording method, or how the files were created (B right, About MP3/

JPEG/DivX files).

≥ During playback of DTS source, there will be no sound from the

speakers.

Blu-ray Discs, HD DVD, AVCHD discs, DVD-RW version 1.0, DVD-Audio,

DVD-ROM, DVD-VR, CD-ROM, CDV, CD-G, SACD, DTS Music Discs,

WMA discs and Photo CD, DVD-RAM, and “Chaoji VCD” available on the

market including CVD, DVCD and SVCD that do not conform to

IEC62107.

This unit can play PAL and NTSC, but the “TV System” (B 17) of this unit

must match the system of your TV.



Depending on the PAL video on the disc, the image may not be displayed

correctly on an NTSC TV.

≥ Do not attach labels or stickers to discs. This may cause disc warping,

rendering it unusable.

≥ Do not write on the label side with a ball-point pen or other writing

instrument.

≥ Do not use record cleaning sprays, benzine, thinner, liquids which

prevent static electricity, or any other solvent.

≥ Do not use scratch-proof protectors or covers.

≥ Do not use the following discs:

– Discs with exposed adhesive from removed stickers or labels (rented

discs, etc.).

– Discs that are badly warped or cracked.

– Irregularly shaped discs, such as heart shapes.

≥ There may be differences in the display order on the menu screen and

computer screen.

≥ This unit cannot play files recorded using packet write.

DVD-R/RW

≥ Discs must conform to UDF bridge (UDF 1.02/ISO9660).

≥ This unit does not support multi-session. Only the default session is

played.

CD-R/RW

≥ Discs must conform to ISO9660 level 1 or 2 (except for extended

formats).

≥ This unit supports multi-session but if there are many sessions it takes

more time for play to start. Keep the number of sessions to a minimum

to avoid this.

USB device

≥ This unit does not guarantee connection with all USB devices.

≥ This unit does not support USB device charging.

≥ FAT12, FAT16 and FAT32 file systems are supported.

≥ This unit supports USB 2.0 Full Speed.

≥ Never use alcohol, paint thinner or benzine to clean this unit.

≥ Before using chemically treated cloth, carefully read the instructions that

came with the cloth.

Do not use commercially available lens cleaners as they may cause

malfunction. Cleaning of the lens is generally not necessary although

this depends on the operating environment.

Media that can be played

Type of media/

Logo

Remarks Indicated as

DVD-Video High quality movie and

music discs

[DVD-V]

Video CD Music discs with video

Including SVCD

(Conforming to IEC62107)

[VCD]

CD Music discs [CD]

Type of media/

Logo

Formats Indicated as

DVD-R/RW ≥ DVD-Video Format

≥ MP3 format

≥ JPEG format

≥ DivX

format

[DVD-V]

[MP3]

[JPEG]

[DivX]

DVD-R DL ≥ DVD-Video Format

≥ DivX

format

[DVD-V]

[DivX]

rR/rRW/rRDL ≥iVR (iR/iRW Video

Recording) Format

[DVD-V]

CD-R/RW ≥ CD-DA format

≥ MP3 format

≥ JPEG format

≥ DivX

format

[CD]

[MP3]

[JPEG]

[DivX]

USB device ≥ MP3 format

≥ JPEG format

≥ DivX

format

[MP3]

[JPEG]

[DivX]

Note about using a DualDisc

The digital audio content side of a DualDisc does not meet the technical

specifications of the Compact Disc Digital Audio (CD-DA) format so

playback may not be possible.

Discs that cannot be played

Video systems

Disc handling precautions

About MP3/JPEG/DivX files

[MP3] (Extension: “.MP3”, “.mp3”)

≥ Sampling frequency and compression rate:

–8

kHz

, 11.02

kHz

, 12

kHz

, 16

kHz

, 22.05

kHz

, 24 kHz (8

kbps

160 kbps), 32

kHz

, 44.1

kHz

and 48 kHz (32 kbps to 320 kbps)

≥ ID3 tags: version 1, 2

[JPEG] (Extension: “.JPG”, “.jpg”, “.JPEG”, “.jpeg”)

≥ JPEG files taken on a digital camera that conform to DCF Standard

(Design rule for Camera File system) Version 1.0 are displayed.

– Files that have been altered, edited or saved with computer picture

editing software may not be displayed.

≥ This unit cannot display moving pictures, MOTION JPEG and other

such formats, still pictures other than JPEG (e.g. TIFF), or play

pictures with attached audio.

[DivX] (Extension: “.DIVX”, “.divx”, “.AVI”, “.avi”)

≥ DivX files greater than 2 GB or have no index may not be played

properly on this unit.

≥ This unit supports all resolutions up to maximum of 720k480

(NTSC)/720k576 (PAL).

Maintenance

Clean this unit with a soft, dry cloth

Before moving the unit, ensure the disc tray is empty. Failure to

do so will risk severely damaging the disc and the unit.

SC-XH175 EP_RQT9597-R_eng.book Page 19 Wednesday, December 14, 2011 9:38 AM

RQT9597

ENGLISH

You can attach all of the speakers (except subwoofer) to a wall.

≥ The wall or pillar on which the speakers are to be attached should be

capable of supporting 10 kg per screw. Consult a qualified building

contractor when attaching the speakers to a wall. Improper attachment

may result in damage to the wall and speakers, and personal injury.

1 Drive a screw (not supplied) into the wall.

2 Fit the speaker securely onto the screw(s) with the hole(s).

∫ Tips

Use the measurements indicated below to identify the screwing positions

on the wall.

≥ Leave at least 20 mm of space above the speaker and 10 mm on each

side to allow enough space for fitting the speaker.

Speaker installation option

Attaching to a wall

e.g., Surround speaker

DO NOT DO

≥ In this position, the speaker will

likely fall if moved to the left or

right.

≥ Move the speaker so that the

screw is in this position.

Surround speaker Center speaker

At least 30 mm

‰7.0 mm to ‰9.4 mm

Wall or pillar

5.5 mm to 7.5 mm

‰4.0 mm









A 24 mm

B 116 mm

C 40 mm

D 40 mm











E 18 mm

F 65 mm

G 24 mm

H 95.5 mm

I 27 mm

Front speaker

Attach to a wall without the base and the stand

∫ To prevent speakers from falling

Front speaker, Surround speaker, Center speaker

e.g. Front speaker











J 65 mm

K 349 mm

L 110 mm

M 51 mm

N 51 mm

Wall

Screw eye

(not supplied)

String (not supplied)

Less than

10 cm

Reattaching the speaker cable

Insert the cable

from the bottom.

Pull out the cable

through the hole.

Leave about

120 mm.

SC-XH175 EP_RQT9597-R_eng.book Page 20 Wednesday, December 14, 2011 9:38 AM

Stránka sa načítava...

Panasonic SC-XH175 Návod na používanie

Značka: Panasonic

Model: SC-XH175

Kategória: Blu-Ray prehrávače

Typ: Návod na používanie

Tento návod je vhodný aj pre

SCXH175EP

Stiahnite si PDF

správa

v iných jazykoch

English: Panasonic SC-XH175 Operating instructions
polski: Panasonic SC-XH175 Instrukcja obsługi

Panasonic SC-XH175 Návod na používanie

Tento návod je vhodný aj pre

Panasonic SC-XH175 Návod na používanie

v iných jazykoch

Súvisiace články

Ostatné dokumenty