Simplicity 540477-2220-G1 Používateľská príručka

Kategória
Motor
Typ
Používateľská príručka
Operator's Manual
Инструкции за експлоатация
Návod k obsluze
Kasutusjuhend
Priruènik za operatora
Kezelési útmutató
Naudojimo instrukcija
Operatora rokasgrāmata
Instrukcja obsługi
Manual de utilizare
Руководство по эксплуатации
Návod na obsluhu
Priroènik za uporabo
Kullanma Kilavuz
Models:54E000,540000,61E000,610000,61G200,
61G300
© Briggs & Stratton. All rights reserved. 80102665
Revision A
Not for
Reproduction
1
2
3
4
5
6
7
8
9
2 vanguardpower.com
Not for
Reproduction
10
11
12
13
14
15
16
17
18
3
Not for
Reproduction
General Information
This manual contains safety information so that you will know the hazards and risks
related to this engine and how to prevent them. It also contains instructions for the
correct use and maintenance of the engine. Because Briggs & Stratton does not know
what equipment this engine will power, it is important that you read, understand, and
obey these instructions. Save these original instructions for future reference.
NOTE:The figures and illustrations in this manual are for reference only and can be
different from your model. If you need help, contact an Authorized Service Dealer.
For replacement parts or technical help, record the date of purchase, engine model,
type, trim, and the engine serial number. These numbers are located on your engine.
Refer to the Features and Controls section.
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
European Office Contact Information
For questions related to European emissions, contact our European office at:
Max-Born-Straße 2, 68519 Viernheim, Germany.
European Union (EU) Stage V (5): Carbon
Dioxide (CO2) Values
Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values
of Briggs & Stratton EU Type-Approval Certificate engines.
Recycling Information
Recycle all cartons, boxes, used oil, and batteries as
specified by government regulations.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol identifies safety information about hazards that could
result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to
indicate the likelihood and the potential severity of injury. In addition, a hazard symbol
is used to represent the type of hazard.
DANGER indicates a hazard which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not avoided, could result in minor or moderate
injury.
NOTICE indicates information considered important but not hazard-related.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire Hazard Explosion Hazard
Shock Hazard Toxic Fume Hazard
Hot Surface Hazard Noise Hazard - Ear
protection recommended
for extended use.
Thrown Object Hazard -
Wear eye protection.
Explosion Hazard
Frostbite Hazard Kickback Hazard
Amputation Hazard -
Moving Parts
Chemical Hazard
Thermal Heat Hazard Corrosive Hazard
Safety Messages
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products, see
www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs
& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result
in serious injury or death.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
Fill the fuel tank outdoors or in an area that has good airflow.
Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
If fuel spills, wait until it dries before you start the engine.
When you start the engine
Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are
correctly installed.
Do not crank the engine with the spark plug removed.
If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
When you operate the equipment
Do not tilt the engine or the equipment at an angle which causes fuel to spill.
Do not choke the carburetor (if equipped) to stop the engine.
Do not start or operate the engine with the air cleaner (if equipped) or the air
filter (if equipped) removed.
When you do maintenance
If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occurand could result a fire or an explosion.
During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,
if mounted on the engine, is empty and that the spark plug side is up. If the fuel
tank is not empty, leakage can occurand could result a fire or an explosion.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
Do not change the governor spring, links or other parts to increase engine
speed.
Do not hit the flywheel with a hammer or hard object. This could result in failure
of the flywheel during operation.
Replacement parts must be of the same design and installed in the same
position as the original parts. Other parts could result in damage or an injury.
4 vanguardpower.com
Not for
Reproduction
When you move the location of equipment
Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the
CLOSED position.
When fuel or equipment is in storage with fuel in the fuel tank
Because pilot lights or other ignition sources can cause explosions, keep fuel or
equipment away from furnaces, stoves, water heaters or other appliances that
have pilot lights.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Engine start-up causes spark that could result in a fire or explosion.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and windows
for ventilation. After the operation of this product, carbon monoxide can quickly
collect in these spaces and stay for hours.
ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
Before you start the engine, disconnect or remove all external equipment and
engine loads.
Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
WARNING
Rotating parts can entangle hands, feet, hair, clothing, or accessories and result
in traumatic amputation or laceration.
Operate equipment with the guards correctly installed.
Keep hands and feet away from rotating parts.
Remove jewelry and make sure that long hair is away from all rotating parts.
Do not wear loose clothes or items that could become caught.
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
WARNING
Accidental engine spark can cause an electric shock or fire and could result in
entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect the battery wire from the negative battery terminal (only engines with
electric start.)
Use only the correct tools.
When you check for spark:
Use an approved spark plug tester.
Do not check for spark with the spark plug removed.
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
If you smell gas
Do not start the engine.
Do not switch on electrical switches.
Do not use a phone in the vicinity.
Evacuate the area.
Contact the gas supplier or the fire department.
Features and Controls
Engine Controls
Compare the callout letters in Figures 1, 2, 3, and 4 to the engine controls in the list that
follows:
A. Engine Identification Numbers Model - Type - Code
B. Spark Plug
C. Cyclonic Air Cleaner
D. Low Profile Air Cleaner
E. Dipstick
F. Oil Fill
G. Oil Filter
H. Oil Drain Plug
I. Oil Pressure Sensor
J. Finger Guard
K. Electric Starter
L. Starter Solenoid
M. Regulator / Rectifier
N. Carburetor - Carburetor Models
O. Oil Cooler (if equipped)
P. Muffler (if equipped)
Q. Fuel Pump
R.
Starter Switch
1
S.
Throttle Control
1
T.
ChokeControl(Carburetor Models
1
)
U. Fuel Filter
V. Tachometer (if equipped)
1
Some engines and equipment have remote controls. See the equipment manual for the
location and operation of remote controls.
Engine Control Symbols and Meanings
Engine Speed - FAST Engine Speed - SLOW
Engine Speed - STOP ON - OFF
5
Not for
Reproduction
Engine Start
Choke CLOSED
Engine Start
Choke OPEN
Fuel Cap
Fuel Shut-off OPEN
Fuel Shut-off CLOSED
Fuel Level - Maximum
Do Not Overfill
Operation
Oil Recommendations
Oil Capacity: See the Specifications section.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or
dealers could have added oil to the engine. Before you start the engine for the first time,
make sure that the oil is at the correct level. Add oil as specified by the instructions in
this manual. If you start the engine without oil, damage will occur and the engine will not
be repaired under warranty.
We recommend the use of Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Use the chart to select the best viscosity for the outdoor temperature range expected.
Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For
equipment operated in hot temperatures, Vanguard
®
15W-50 Synthetic oil gives the best
protection.
A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
E
Vanguard
®
Synthetic 15W-50
Check and Add Oil
Before you check or add oil
Make sure the engine is level.
Clean the oil fill area of debris.
Refer to the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or
dealers could have added oil to the engine. Before you start the engine for the first time,
make sure that the oil is at the correct level. Add oil as specified by the instructions in
this manual. If you start the engine without oil, damage will occur and the engine will not
be repaired under warranty.
1. Remove the dipstick (A, Figure 5) and clean with a cloth.
2. Install and tighten the dipstick (A, Figure 5).
3. Remove the dipstick and check the oil level. Make sure that the oil level is at the
top of the full indicator (B, Figure 5) on the dipstick.
4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not add
too much oil. After you add oil, wait one minute and check the oil level again. Make
sure that the oil level is correct.
5. Install and tighten the dipstick (A, Figure 5).
Low Oil Protection System (if equipped)
A low oil sensor is installed on some engines. If the oil is low, the sensor will display a
warning light or stop the engine. Stop the engine and follow these steps before you start
the engine.
Make sure the engine is level.
Do an oil check. Refer to the Check Oil Level section.
If the oil level is low, add the correct amount of oil. Start the engine and make
sure the warning light (if equipped) does not come on.
If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to have the oil problem corrected.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
Gasoline with up to 10% ethanol (gasohol) is permitted.
NOTICE
Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or
change the engine to operate on alternate fuels. Use of unapproved fuels could result in
damage to engine components, which will not be repaired under the warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. Refer
to the Storage section. All fuel is not the same. If start or performance problems occur,
change fuel providers or brands. This engine is certified to operate on gasoline. The
emissions control system for carbureted engines is EM (Engine Modifications). The
emissions control systems for engines with electronic fuel injection are ECM (Engine
Control Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is permitted.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
Fill the fuel tank outdoors or in an area that has good airflow.
Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
If fuel spills, wait until it dries before you start the engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 6) with fuel. Because fuel will expand, do not fill above
the bottom of the fuel tank neck (B).
3. Install the fuel cap.
Start and Stop Engine
Start Engine
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
Before you start the engine, disconnect or remove all external equipment and
engine loads.
Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
6 vanguardpower.com
Not for
Reproduction
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result
in burns or death.
When you start the engine
Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped)
are correctly installed.
Do not crank the engine with the spark plug removed.
If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY.
See a doctor. You may have carbon monoxide poisoning.
Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and
windows for ventilation. After the operation of this product, carbon monoxide
can quickly collect in these spaces and stay for hours.
ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers could have added oil to the engine. Before you start the engine for the
first time, make sure that the oil is at the correct level. Add oil as specified by the
instructions in this manual. If you start the engine without oil, damage will occur and the
engine will not be repaired under warranty.
Types of Starting Systems
Before you start the engine, you must know the type of starting system on your engine.
Your engine will have one of these types.
Electronic Fuel Injection (EFI) System: An EFI system does not have a
choke or a primer.
Choke System: This type of system has a choke to be used in cool
temperatures. Some models will have a separate choke control while others
will have a combination choke and throttle choke. It does not have a primer.
NOTE:Your equipment could have remote controls. Refer to the equipment manual for
location and operation of remote controls.
Electronic Fuel Injection (EFI) System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate
the engine in the FAST position.
5. Turn the electric start switch (D, Figure 7) to the ON or START position.
NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).
Wait one minute between start cycles.
If the engine does not start after 3or 4 times, contact your local dealer or goto
vanguardpower.com or call 1-800-999-9333.
Choke System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate
the engine in the FAST position.
5. Move the choke control (C, Figure 7), or the combination choke and throttle (B,C) to
the CLOSED position.
NOTE:To start the engine with a dry fuel system, additional cranking time in the choke
position will be required. This will give the fuel pump time to prime the fuel system.
6. Turn the key switch (D, Figure 7) to the ON or START position.
7. If the engine starts but will not continue to operate, move the choke control (C,
Figure 7) to the OPEN position to start the engine.
NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).
Wait one minute between start cycles.
8. As the engine warms, move the choke control (C, Figure 7) to the OPEN position.
If the engine does not start after 3or 4 times, contact your local dealer or goto
vanguardpower.com or call 1-800-999-9333.
Stop the Engine
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Do not choke the carburetor (if equipped) to stop the engine.
1. With the throttle control in the SLOW position, turn the electric start switch (D,
Figure 7) to the OFF position. Remove the key and keep it in a safe place out of the
reach of children.
2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the
CLOSED position.
Maintenance
Maintenance Information
WARNING
During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if
mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not
empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted
in a different direction, it will not easily start because of oil or fuel contamination of the air
filter or the spark plug.
We recommend that you see a Briggs & Stratton Authorized Service Dealer for all
maintenance and servicing of the engine and engine parts.
NOTICE
All the components used to build this engine must remain in place for correct operation.
WARNING
Accidental engine spark can cause an electric shock or fire and could result in
entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect the battery wire from the negative battery terminal (only engines with
electric start.)
Use only the correct tools.
When you check for spark:
Use an approved spark plug tester.
Do not check for spark with the spark plug removed.
Emissions Control Service
For maintenance, replacement, or repair of emissions control devices and
systems, contact a qualified off-road engine repair establishment or service
technician. However, for "no charge" emissions control service, the work must be done
by a factory authorized dealer. Refer to the Emissions Control Statements.
Maintenance Schedule
Intervals of 8 Hours or Daily
Check the engine oil level.
Clean the area around the muffler and controls.
Intervals of 100 Hours or Annually
7
Not for
Reproduction
Clean or replace the air filter
1 2
.
Change the engine oil and filter.
Replace the oil filter (if equipped).
Replace the spark plugs.
Check the muffler and spark arrester.
Service the exhaust system.
Intervals of 250 Hours or Annually
Check the valve clearance. Adjust if necessary.
Intervals of 400 Hours or Annually
Change the air filter
2
.
Replace the fuel filter.
Service the air cooling system
1
.
Clean the oil cooler fins
1
.
Intervals of 600 Hours
Replace the safety filter, if equipped.
1
In dusty conditions or when airborne debris is present, clean more frequently.
2
Every third air filter change, replace the inner safety filter (if equipped.
Electronic Fuel Injection (EFI) System
The EFI System monitors engine temperature, engine speed, and battery voltage for
engine start-up and warm-up. There are no adjustments on the system. If start-up or
operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.
NOTICEMake sure to obey the steps that follow or damage to the EFI system could
occur.
DO NOT start the engine if the battery cables are loose.
Turn the key to the OFF position before you disconnect, remove, and / or install
the battery.
DO NOT use a battery charger to start the engine.
DO NOT disconnect the battery cables during engine operation.
When you disconnect the battery cables, first connect the positive (+) cable, and
then connect the negative (-) cable to the battery.
When you charge the battery, turn the ignition switch to the OFF position,and
disconnect the negative (-) battery cable from the battery.
DO NOT spray water directly on the Electronic Control Module.
Carburetor and Engine Speed
Do not make adjustments to the carburetor or engine speed. The carburetor was set at
the factory to operate satisfactorily under most conditions. Do not change the governor
spring, linkages, or other parts to adjust the engine speed. If any adjustments are
required contact a Briggs & Stratton Authorized Service Dealer for service.
NOTICE
The equipment manufacturer specifies the maximum speed for the engine as installed
on the equipment. Do not exceed this speed. If you are not sure what the equipment
maximum speed is, or what the engine speed is set to from the factory, contact a Briggs
& Stratton Authorized Service Dealer for assistance. For safe and correct operation
of the equipment, the engine speed should only be adjusted by a qualified service
technician.
Servicing the Spark Plug
Check the spark plug gap (A, Figure 8) with a wire gauge (B). If necessary, set the
spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque
specifications, refer to the Specifications section.
NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug
to decrease ignition signals.If a resistor spark plug was installed by the equipment
manufacturer, use the same type for replacement.
Servicing theExhaust System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Remove debris from the muffler and cylinder area. Examine the muffler for cracks,
corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and
examine for damage or carbon blockage. If damage is found, install the replacement
parts before you operate the equipment.
WARNING
Replacement parts must be of the same design and installed in the same position as the
original parts. Other parts could result in damage or an injury.
Change Engine Oil
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occur and cause a fire or an explosion.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Used oil is a hazardous waste product and must be discarded of correctly. Do not
discard with household waste. Contact your local authorities, service center, or dealer
for safe disposal or recycling facilities.
Remove Oil
1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 9), and
keep it away from the spark plug(s)(E).
2. Remove the dipstick (A, Figure 10).
3. Remove the oil drain plug (F, Figure 11). Drain the oil into an approved container.
4. Install and tighten the oil drain plug(F, Figure 11).
Change Oil Filter, if equipped
1. Drain the oil from the engine. Refer to the Remove Oil section.
2. Remove the oil filter (H, Figure 12) anddiscard correctly.
3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.
4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten
the oil filter 1/2 to 3/4 turns.
5. Add oil. Refer to the Add Oil section.
6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.
7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure
5) on the dipstick.
Add Oil
Make sure the engine is level.
Clean the oil fill area of all debris.
Refer to the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 10). Remove oil from the dipstick with a clean cloth.
2. Slowly add oil into the engine oil fill (C, Figure 10). Do not overfill. Wait one
minute and then check the oil level.
3. Install and tighten the dipstick (A, Figure 10).
4. Remove the dipstick and check the oil level. The correct oil level is at the top of the
full indicator (B, Figure 10) on the dipstick.
5. Install and tighten the dipstick (A, Figure 10).
6. Connect the spark plug wire(s) (D, Figure 9) to the spark plug(s) (E).
Servicing the Air Filter
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
Do notstart and operate the engine with the air cleaner assembly (if equipped)
or the air filter (if equipped) removed.
8 vanguardpower.com
Not for
Reproduction
NOTICE
Do not use pressurized air or solvents to clean the filter. Pressurized air could result in
damage to the filter and solvents will dissolve the filter.
See the Maintenance Schedule for service requirements.
Different models will use a foam or a paper filter. Some models could also have an
optional pre-cleaner that can be washed and used again. Compare the illustrations in
this manual with the type installed on your engine and service as follows.
Cyclonic Air Filter
1. Open the fastener(s) (A, Figure 13) and remove the cover (B).
2. Remove the air filter (C, Figure 13).
3. To loosen debris, lightly tap the air filter on a hard surface. If the air filter is dirty,
replace it with a new air filter.
4. To remove the safety filter (D, Figure 13), if equipped, carefully pull it away from the
air cleaner body (E). Make sure that dirt or debris does not go into the engine.
5. Install the new safety filter (D, Figure 13) in the air cleaner body (E).
6. Install the air filter (C, Figure 13) above the safety filter (D).
7. Install the cover (B, Figure 13) and close the fastener(s) (A).
Low Profile Air Filter
1. Remove the fastener(s) (A, Figure 14).
2. Remove the cover (B, Figure 14).
3. Remove the fastener(s) (C, Figure 14) and retainer (D).
4. Remove the air filter (E, Figure 14).
5. Remove the pre-cleaner (F, Figure 14), if equipped, from the air filter (E).
6. To loosen debris, lightly tap the air filter (E, Figure 14) on a hard surface. If the air
filter is dirty, replace with a new air filter.
7. Clean the pre-cleaner (F, Figure 14), if equipped, in liquid detergent and water.
Make sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.
8. Assemble the dry pre-cleaner (F, Figure 14), if equipped, to the air filter (E).
9. Install the air filter (E, Figure 14) with the retainer (D) and fastener(s) (C).
10. Install the cover (B, Figure 14) with the fastener(s) (A). Make sure the fastener(s) is
tight.
Servicing the Cooling System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible debris, such as leaves, grass, and brush can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
NOTICE
Do not use water to clean the engine. Water could cause contamination of the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to
become too hot and result in unsatisfactory performance and decreased engine life.
1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 15).
2. Keep linkage, springs, and controls (B, Figures 15, 16) clean.
3. Keep the area around and behind the muffler (C, Figures 15, 16) free of
combustible debris.
4. Make sure the oil cooler fins (D, Figure 15) are free of dirt and debris.
5. Loosen the fastener(s) (E, Figures 15, 16) and remove the debris access panels
(F). Remove grass and debris that has collected on the cylinders.
6. Install the debris access panels (F, Figures 15, 16) and attach with fastener(s) (E).
After a period of time, debris can collect in the cylinder cooling fins and cause the engine
to overheat. This debris cannot be removed without partial disassembly of the engine.
As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized
Service Dealer inspect and clean the air cooling system.
Servicing the Fuel System
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
Before you clean or replace the fuel filter, drain the fuel tank or close the fuel
shut-off valve.
If fuel spills, wait until it dries before you start the engine.
Replacement parts must be of the same design and installed in the same
position as the original parts. Other parts could result in damage or an injury.
Fuel Filter, if equipped
1. Before you clean or replace the fuel filter (A, Figure 17), drain the fuel tank or close
the fuel shut-off valve. If the fuel tank is not drained, fuel leakage could occur and
cause a fire or explosion.
2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then move the clamps
away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.
3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.
4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.
5. Attach the fuel lines (D, Figure 17) with clamps (C).
Storage
Fuel System
Refer to Figure: 18.
Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 18) with
fuel. For fuel expansion, do not fill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. Each
time you fill the container with fuel, addfuel stabilizerto the fuel as specified by the
manufacturer’s instructions. This keeps fuel fresh and decreases fuel-related problems
or contamination in the fuel system.
It is not necessary to drain fuel from the engine whenfuel stabilizeris added as
instructed. Before storage, turn the engine ON for 2 minutes to move the fuel and
stabilizer through the fuel system.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained
into an approved container. Operate the engine until it stops from lack of fuel. The use of
a fuel stabilizer in the storage container is recommended to keep fuel fresh.
Engine Oil
While the engine is still warm, change the engine oil. Refer to Change the Engine Oil
section.
Troubleshooting
Assistance
For assistance, contact your local dealer or go to vanguardpower.com or call
1-800-999-9333 (in USA).
Specifications
Specifications and Service Parts
Models: 540000 , 54E000
Displacement 54.68 ci (896 cc)
Bore 3.366 in ( 85,5 mm)
Stroke 3.071 in (78,0 mm)
Oil Capacity 78 - 80 oz (2,3 - 2,4 L)
Spark Plug Gap .030 in (,76 mm)
Spark Plug Torque 180 lb-in (20 Nm)
Armature Air Gap .005 - .008 in (,13 - ,20 mm)
Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)
Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)
Models: 610000, 61E000, 61G200, 61G300
Displacement 60.60 ci (993 cc)
Bore 3.366 in ( 85,5 mm)
9
Not for
Reproduction
Models: 610000, 61E000, 61G200, 61G300
Stroke 3.406 in (86,5 mm)
Oil Capacity 78 - 80 oz (2,3 - 2,4 L)
Spark Plug Gap .030 in (,76 mm)
Spark Plug Torque 180 lb-in (20 Nm)
Armature Air Gap .005 - .008 in (,13 - ,20 mm)
Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)
Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)
Service Parts - Models: 540000, 54E000,
610000, 61E000, 61G200, 61G300
Service Part Part Number
Cyclonic Air Filter (Figure 13) 841497
Cyclonic Safety Filter (Figure 13) 821136
Air Filter, Low Profile (Figure 14) 692519
Pre-cleaner, Low Profile (Figure 14) 692520
Oil - SAE 30 100028
Oil Filter 842921
Fuel Filter 691035
Resistor Spark Plug 491055
Long Life Platinum Spark Plug 5066
Spark Plug Wrench 19374
Spark Tester 19368
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily
at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted
operating limits on slopes.
Power Ratings
The gross power rating for individual gasoline engine models is labeled in accordance
with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque
Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM
for all others; horsepower values are derived at 3600 RPM. The gross power curves
can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with
exhaust and air cleaner installed whereas gross power values are collected without
these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the
variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
Warranty
Briggs & Stratton Engine Warranty
Effective January 2019
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this
warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
The purchaser must contact the Authorized Service Dealer, and then make the product
available to the Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law. Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state and country to country
4
.
Standard Warranty Terms
1, 2, 3
Vanguard®; Commercial Series
3
Consumer Use - 36 months
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
1
These are our standard warranty terms, but occasionally there may be additional
warranty coverage that was not determined at time of publication. For a listing
of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or
contact your Briggs & Stratton Authorized Service Dealer.
2
There is no warranty for engines on equipment used for prime power in place
of a utility; standby generators used for commercial purposes, utility vehicles
exceeding 25 MPH, or engines used in competitive racing or on commercial or
rental tracks.
3
Vanguard installed on standby generators: 24 months consumer use, no
warranty commercial use. Commercial Series with manufacturing date before July
2017: 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by
emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or
commercial consumer. "Consumer use" means personal residential household use by a
retail consumer. "Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial
use, it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial
purchase date at the time warranty service is requested, the manufacturing date
of the product will be used to determine the warranty period. Product registration
is not required to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than
10%, or the use of alternative fuels such as liquefied petroleum or natural gas on
engines not originally designed/manufactured by Briggs & Stratton to operate on
such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
10 vanguardpower.com
Not for
Reproduction
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. F)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2020-2022 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards. B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.
If any emissions-related part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual. B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations adopted by the Air Resources Board; that
it is free from defects in material and workmanship that could cause the failure
of a warranted part; and that it is identical in allmaterial respects to the engine
described in the manufacturer’s application for certification. The warranty period
begins on the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled for replacement as required
maintenance in the Operators’s Manual supplied, is warranted for the period
of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired
or replaced by B&S at no charge to the owner. Any such part repaired or
replaced under warranty will be warranted for the remainder of the period
prior to the first scheduled replacement point for the part.
Add-on or modified parts that are not exempted by the Air Resources Board
may not be used. The use of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty claim. The manufacturer
will not be liable to warrant failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
The Emissions Durability Period describes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, the Emissions Durability Period of an engine with an intermediate rating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
11
Not for
Reproduction
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80099153(Revision A)
Briggs & Stratton Emissions Warranty
U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Jx)
The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust
emissions control system warranty on your Model Year 2020-2022 engine. In the U.S,
new small off-road engines and large spark ignited engines less than or equal to 1.0
liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S
must warrant the emissions control system on your engine for the periods of time listed
below provided there has been no abuse, neglect, or improper maintenance of your
engine leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years. If
any emissions-related parts on your engine is defective, the part will be repaired of
replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the performance of the required
maintenance listed in your Operator’s Manual. B&S recommends that you
retain all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or your failure to ensure the
performance of all scheduled maintenance.
As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect,
improper maintenance, or unapproved modifications.
You are responsible for presenting your engine to a B&S distribution center,
or service center, as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations under Section 213 of the Clean Air Act that
is free from defects in material and workmanshipthat could cause the failure of a
warranted part; and that is identical in all material respects to the engine described
in the manufacturer’s application for certification. The warranty period begins on
the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled for replacement as required
maintenance in the Operator's Manual supplied, is warranted for the period of
time prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or replaced
by B&S at no charge to the owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
Add-on or modified parts that are not exempted by the U.S. EPA may not be
used. The use of any non-exempted add-on or modified parts by the owner
will be grounds for disallowing a warranty claim. The manufacturer will not
be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of
operating hours for which the engine has been shown to meet Federal emissions
requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80099149 (Revision A)
12 vanguardpower.com
Not for
Reproduction
Обща информация
Това ръководство съдържа информация за безопасна работа, за да сте наясно с
опасностите и рисковете, свързани с този двигател и как да ги предотвратите. То
съдържа също инструкции за правилна употреба и техническо обслужване. Тъй
като в Briggs & Stratton не знаят каква машина ще се задвижва с този двигател,
важно е да прочетете, разберете и спазвате тези инструкции. Запазете тези
оригинални инструкции за бъдещи справки.
ЗАБЕЛЕЖКА:Данните и илюстрациите в настоящото ръководство са
предоставени само за справка и може да се различават от Вашия конкретен
модел. При нужда от помощ, се свържете с упълномощен сервизен представител.
Относно резервните части или техническата помощ, запишете датата на
покупката, модела, типа, конструкцията и серийния номер на двигателя. Тези
номера са разположени върху Вашия двигател. Вижте раздела Елементи и
прибори за управление.
Дата на закупуване
Модел - Тип - Конструкция на
двигателя
Сериен номер на двигателя
Информация за контакт на Европейската
служба
За въпроси относно емисиите в Европейския съюз, се свържете с нашата
Европейска служба на адрес:
Max-Born-Straße 2, 68519 Viernheim, Германия.
Стандарт Euro ниво V (5) на ЕС:
Стойности на въглероден диоксид (CO2)
Въведете „CO2“ в полето за търсене на уебсайта BriggsandStratton.com, за да
намерите стойностите на емисиите въглероден диоксид за двигателите на Briggs &
Stratton, които имат сертификат за типово одобрение от ЕС.
Информация за рециклиране
Рециклирайте всички кашони, кутии, използвано масло
и батерии, както е посочено в правителствените
разпоредби.
Безопасност на оператора
Предупредителен символ за опасност и
сигнални думи
Предупредителният символ за безопасност се използва за обозначаване
на информацията за безопасност, свързани с опасности, които могат да доведат
до нараняване. Сигнализираща дума (ОПАСНОСТ,ПРЕДУПРЕЖДЕНИЕ или
ВНИМАНИЕ) се поставя, за да посочи вероятността и потенциалната сериозност
на нараняването. Освен това, даден символ за опасност се използва, за да се
представи видът на опасността.
ОПАСНОСТ посочва опасност, която, ако не бъде избегната, ще доведе до смърт
или сериозно нараняване.
ПРЕДУПРЕЖДЕНИЕ посочва опасност, която, ако не бъде избегната, може да
доведе до смърт или сериозно нараняване.
ВНИМАНИЕ посочва опасност, която, ако не бъде избегната, може да доведе до
малка или средна степен на нараняване.
ПРЕДУПРЕЖДЕНИЕпосочва информация, считана за важна, но несвързана с
опасности.
Символи за опасности и техните значения
Информация за
безопасност относно
опасности, които могат
да доведат до телесно
нараняване.
Прочетете и разберете
Ръководството за
оператора, преди да
работите или правите
техническо обслужване
на машината.
Опасност от пожар Опасност от експлозия
Опасност от
електрически удар
Опасност от токсични
пари
Опасност от нагорещена
повърхност
Опасност от висок шум
– При продължително
ползване се препоръчва
защита на слуха.
Опасност от изхвърляне
на предмет – Носете
защитни очила.
Опасност от експлозия
Опасност от обледяване Опасност от откат
Опасност от отрязване
на крайник – Движещи се
части
Опасност от химикали
Опасност от топлинно
въздействие
Опасност от корозия
Съобщения за безопасност
ПРЕДУПРЕЖДЕНИЕ
Двигателите на Briggs & Stratton® не са предназначени за и не трябва да се
използват за захранване на: развлекателни картове; състезателни картове;
детски, развлекателни или спортни вседеходни превозни средства (АТВ-
та); мотоциклети; съдове на въздушна възглавница; продукти за авиацията
или превозни средства, използвани в състезания, които не са разрешени
от Briggs & Stratton. За информация относно изделия за състезателни цели,
вижте www.briggsracing.com. При използване на превозни средства с общо
предназначение и такива с повишена проходимост (ATV), моля свържете се с
приложния център за захранване на Briggs & Stratton на тел. 1-866-927-3349.
Неправилната употреба на двигателя може да доведе до сериозни наранявания
или смърт.
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Когато добавяте гориво
Спрете двигателя. Преди да свалите капачката за гориво, изчакайте най-
малко две (2) минути, за да си гарантирате, че двигателят се е охладил.
Напълнете резервоара за гориво на открито или в помещение с добра
вентилация.
Не слагайте твърде много гориво в резервоара. За да оставите възможност
за разширение на горивото, не пълнете над долната част на гърлото на
резервоара за гориво.
Дръжте горивото далече от искри, открити пламъци, пилотни светлини,
топлина и други източници на запалване.
Често преглеждайте горивопроводите, резервоара за гориво, капачката
на горивото и връзките за наличие на пукнатини или течове. Подменете
повредените части.
Ако горивото се разлее, изчакайте, докато се изпари преди да стартирате
двигателя.
Когато стартирате двигателя
Уверете се, че запалителната свещ, шумозаглушителят, капачката на
резервоара за гориво и въздушният филтър (ако има такива) са монтирани
правилно.
Не стартирайте двигателя без запалителна свещ.
Ако двигателят е задавен, поставете смукача (ако има такъв) в положение
ОТВОРЕНО или РАБОТА. Поставете прибора за управление на дроселната
клапа в положение БЪРЗО (ако има такъв) и въртете, докато двигателят
стартира.
13
Not for
Reproduction
Ако в областта има изтичане на природен газ или газ LP, не стартирайте
двигателя.
Не използвайте течности за начално запалване под налягане, защото
парите им са възпламеними.
Когато работите с оборудването
Не накланяйте двигателя или машината под ъгъл, при който горивото се
разлива.
Не запушвайте карбуратора (ако има такъв) за да спрете двигателя.
Не стартирайте и не работете с двигателя при демонтиран комплект на
въздушния филтър (ако има такъв) или със свален въздушен филтър (ако
има такъв).
Когато извършвате техническо обслужване
Ако източвате маслото от горната тръба за пълнене на масло, резервоарът
за гориво трябва да бъде празен. Ако не е празен, може да изтече гориво и
да причини пожар или експлозия.
По време на поддръжката, ако е необходимо да наклоните уреда, уверете
се, че резервоарът за гориво, ако е монтиран на двигателя, е празен и че е
изправен откъм страната на запалващата свещ. Ако резервоарът за гориво
не е празен, може да изтече гориво и да причини пожар или експлозия.
Често преглеждайте горивопроводите, резервоара за гориво, капачката
на горивото и връзките за наличие на пукнатини или течове. Подменете
повредените части.
Не променяйте регулираща пружина, връзки или други части, за да
повишавате оборотите на двигателя.
Не удряйте маховика с чук или твърд предмет. Това може да доведе до
повреда на маховика по време на работа.
Резервните части трябва да бъдат със същата конструкция и да се
монтират в същото положение, както оригиналните части. Другите части
може да се повредят или да се причини нараняване.
Когато местите местоположението на оборудването
Уверете се, че резервоарът за гориво е ПРАЗЕН и че клапаните за
изключване са в позиция ЗАТВОРЕНО.
Когато складирате гориво или оборудване с гориво в резервоара
Тъй като сигналните светлини или други източници на запалване могат да
причинят експлозии, дръжте горивото или оборудването далеч от пещи,
печки, бойлери или други уреди, които имат сигнални светлини.
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Стартирането на двигателя предизвиква искра, която може да доведе до
пожар или експлозия.
Ако в областта има изтичане на природен газ или газ LP, не стартирайте
двигателя.
Не използвайте течности за начално запалване под налягане, защото
парите им са възпламеними.
ПРЕДУПРЕЖДЕНИЕ
ОПАСНОСТ ОТ ОТРОВНИ ГАЗОВЕ. Отработените газове от двигателя
съдържат въглероден оксид, отровен газ, който би могъл да Ви убие за
минути. Дори ако не усещате отработените газове, все още можете да бъдете
изложени на въздействието на отровен въглероден оксид. Ако усетите
гадене, замайване или слабост докато използвате този продукт, ВЕДНАГА
излезте на чист въздух. Отидете на лекар. Възможно е да сте получили
отравяне с въглероден окис.
Въглеродният окис може да се натрупва в затворени помещения.
Работете с този продукт САМО на открито, далече от прозорци, врати и
вентилационни отвори, за да намалите риска от натрупване на въглероден
окис.
Монтирайте сигнални уредби за наличие на въглероден оксид, захранвани
с батерии или чрез щепсел, според инструкциите на производителя.
Сигналните уредби за дим не могат да засичат въглероден окис.
НЕ РАБОТЕТЕ с този продукт в домове, гаражи, мазета, непреходни
коридори, хангари или други затворени помещения, дори при използване
на вентилатори или при отворени врати и прозорци за вентилация. След
работата с този продукт, въглеродният окис може бързо да се натрупа в
тези помещения и да остане с часове.
ВИНАГИ поставяйте този продукт по посока на въздушното течение
и насочвайте изгорелите газове от двигателя далече от обитаваните
помещения.
ПРЕДУПРЕЖДЕНИЕ
Бързото изтегляне на въжето на стартера (откат) притегля дланта и ръката
Ви към двигателя по-бързо, отколкото Вие можете да я отдръпнете. Това
може да причини счупване на кости, фрактури, натъртвания или навяхвания.
За да избегнете отката, при стартиране на двигателя, издърпайте бавно
въжето на стартера, докато усетите съпротивление, а след това дръпнете
рязко.
Изключете или премахнете всички външни товари на оборудването/
двигателя, преди да го стартирате.
Уверете се, че директно прикачените към двигателя елементи, като, но не
само остриета, крилни витла, лебедки и зъбни колела, трябва да бъдат
правилно прикрепени.
ПРЕДУПРЕЖДЕНИЕ
Въртящите се части могат да захванат ръце, крака, коса, облекло или
аксесоари и това може да доведе до травматична ампутация или сериозно
нараняване.
Работете с оборудването с правилно поставени предпазители.
Дръжте ръцете и краката си на разстояние от въртящите се части.
Свалете бижутата си и се уверете, че косата Ви е далече от всички
въртящи се части.
Не носете широки дрехи или аксесоари, които могат да бъдат захванати.
ПРЕДУПРЕЖДЕНИЕ
По време на работа, двигателят и шумузаглушителят се нагорещяват. Ако
докоснете горещ двигател, може да се изгорите.
Запалимите материали, като листа, трева и сухи клонки, могат да се запалят.
Преди да докоснете двигателя или шумозаглушителя, спрете двигателя
и изчакайте две (2) минути. Уверете се, че е безопасно да докосвате
двигателя и шумозаглушителя.
Отстранете отпадъците от шумозаглушителя и двигателя.
Според Правилника на Калифорния за обществените ресурси, раздел 4442,
използването или работата с двигателя по залесени с гори, храсти или с треви
площи представлява нарушение, освен ако системата за отработени газове не
е снабдена с искрогасител, поддържан в ефикасно работно състояние, както е
определено в раздел 4442. Други щати или федерални юрисдикции могат да имат
подобни закони; за справка – Федерален регламент 36CFR, част261.52. Свържете
се с производителя, търговеца или продавача на оригинално оборудване, за да
получите искроуловител, проектиран за системата за отработени газове на този
двигател.
ПРЕДУПРЕЖДЕНИЕ
Случайна искра на двигателя може да причини токов удар или пожар, и може
да доведе до заплитане, травматична ампутация или разкъсване.
Преди да извършвате настройки или поправки:
Откачете кабела на запалителната свещ и го дръжте далече от нея.
Откачете кабела на отрицателната клема на акумулатора (само при
двигатели с електрически стартер).
Използвайте само правилните инструменти.
Когато проверявате за искра:
Използвайте одобрен тестер за свещи.
Не проверявайте за искра при извадена запалителна свещ.
ПРЕДУПРЕЖДЕНИЕ
Изпаренията на горивата са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Ако Ви замирише на газ
Не стартирайте двигателя.
Не включвайте електрическите ключове.
Не използвайте телефон в непосредствена близост.
Напуснете мястото.
Повикайте доставчика на газ или противопожарната служба.
Елементи и прибори за управление
Управления на двигателя
Сравнете допълнителните букви на фигури 1, 2, 3 и 4 с приборите за управление
на двигателя в списъка, по-долу:
A. Маркировка на двигателя Модел – Тип – Код
14 vanguardpower.com
Not for
Reproduction
B. Запалителна свещ
C. Въздушен циклон-филтър
D. Въздушен филтър с нисък профил
E. Нивопоказател
F. Отвор за наливане на масло
G. Маслен филтър
H. Пробка за източване на маслото
I. Датчик за налягане на маслото
J. Предпазител за пръсти
K. Електрически стартер
L. Индукционна бобина за стартиране
M. Регулатор/Изправител
N. Карбуратор - Модели карбуратори
O. Охладител на маслото (ако има такъв)
P. Шумозаглушител (ако има такъв)
Q. Помпа за гориво
R.
Превключвател на стартера
1
S.
Ръчна газ
1
T.
Лост на смукача (модели карбуратори
1
)
U. Филтър за гориво
V. Тахометър (ако има такова оборудване)
1
Някои двигатели и оборудване са снабдени с устройства за дистанционно
управление. Вижте ръководството за работа с оборудването за разположението и
работата с приборите за дистанционно управление.
Символи за управление на двигателя и техните
значения
Обороти на двигателя –
БЪРЗИ
Обороти на двигателя –
БАВНИ
Обороти на двигателя –
СПРЕНИ
ВКЛ. – ИЗКЛ.
Стартиране на двигателя
Смукач ЗАТВОРЕН
Стартиране на двигателя
Смукач ОТВОРЕН
Капачка на резервоара за
гориво
Кранче за подаване на
гориво ОТВОРЕНО
Кранче за подаване на
гориво ЗАТВОРЕНО
Ниво на горивото –
Максимално
Не препълвайте
Експлоатация
Препоръки за маслото
Вместимост на масло: Вижте разделСпецификации.
ПРЕДУПРЕЖДЕНИЕ
Този двигател се доставя от Briggs & Stratton без масло. Производителите на
оборудването или търговците може да са добавили масло в двигателя. Преди
да стартирате двигателя за първи път, уверете се, че маслото е на правилното
ниво. Добавяйте масло, както е посочено в инструкциите в това ръководство. Ако
стартирате двигателя без масло, той ще се повреди и ремонтът няма да бъде
покрит от гаранцията.
За най-добра производителност препоръчваме да се използват сертифицирани
с гаранция масла на Briggs & Stratton
®
. Разрешени са и други висококачествени
почистващи масла от клас SF, SG, SH, SJ или по-висок. Не използвайте специални
добавки.
Използвайте таблицата, за да изберете най-добрия вискозитет за очаквания
диапазон на външна температура. Двигателите на по-голяма част от оборудването
с външно захранване работят добре със синтетично масло 5W-30. Синтетичното
масло Vanguard
®
15W-50 осигурява най-добрата защита за оборудване, което се
използва при високи температури.
A SAE30 – Употребата на SAE30 при температури под 40°F (4°C) ще
доведе до трудно стартиране.
B 10W-30– Употребата на 10W-30 при температури над 80°F (27°C) може
да предизвика повишен разход на маслото. Проверявайте често нивото
на маслото.
С 5W-30
D Синтетично масло 5W-30
E
Синтетично Vanguard
®
15W-50
Проверка и доливане на масло
Преди да проверите или да долеете масло
Уверете се, че двигателят е разположен хоризонтално.
Почистете от отпадъци мястото около отвора за наливане на масло.
Вижте раздел Технически данни относно вместимостта за маслото.
ПРЕДУПРЕЖДЕНИЕ
Този двигател се доставя от Briggs & Stratton без масло. Производителите на
оборудването или търговците може да са добавили масло в двигателя. Преди
да стартирате двигателя за първи път, уверете се, че маслото е на правилното
ниво. Добавяйте масло, както е посочено в инструкциите в това ръководство. Ако
стартирате двигателя без масло, той ще се повреди и ремонтът няма да бъде
покрит от гаранцията.
1. Извадете щеката на нивопоказателя (А, фигура 5) и я почистете с кърпа.
2. Поставете и затегнете щеката на нивопоказателя (A, Фигура 5).
3. Свалете нивопоказателя и проверете нивото на маслото. Уверете се, че
нивото на маслото е до горната част на индикатора за напълване (B, фигура
5) върху щеката.
4. Ако нивото на маслото е ниско, бавно долейте през отвора за моторно масло
(C, Фигура 5). Не добавяйте твърде много масло. След доливане на маслото,
изчакайте една минута и отново проверете нивото. Уверете се, че нивото на
маслото е добре.
5. Поставете и затегнете щеката на нивопоказателя (A, Фигура 5).
Система за защита при ниско ниво на маслото
(ако има такава)
На някои двигатели е инсталиран сензор за ниско ниво на маслото. Ако маслото
е малко, сензорът ще изведе предупредителна светлина или ще спре двигателя.
Спрете двигателя и следвайте тези стъпки, преди да стартирате двигателя.
Уверете се, че двигателят е разположен хоризонтално.
Проврете маслото. Вижте раздел Проверка нивото на маслото.
Ако нивото на маслото е ниско, добавете необходимото количество
масло. Стартирайте двигателя и проверете дали се включва светлинният
индикатор за предупреждение (ако има такъв).
Ако нивото на маслото не е ниско, не стартирайте двигателя. Обърнете
се към упълномощен сервизен представител на Briggs & Stratton, за да
отстраните проблема с маслото.
Препоръки за горивото
Горивото трябва да отговаря на следните изисквания:
Чист, пресен, безоловен бензин.
Минимум 87октана/87AKI (91RON). За работа при голяма надморска
височина вижте по-долу.
Позволен е бензин с до 10% съдържание на етанол (бензоспирт).
15
Not for
Reproduction
ПРЕДУПРЕЖДЕНИЕ
Да не се използват неодобрени марки бензини, като E15 и E85. Не смесвайте
масло с бензина и не променяйте двигателя за работа с алтернативни горива.
Използването на неодобрени горива може да доведе до повреда на елементи от
двигателя, чиито ремонт няма да бъде покрит от гаранцията.
За защита на горивната система от образуване на смола добавете горивен
стабилизатор към горивото. Вижте раздел Съхранение. Всички горива са
различни. Ако започнат да се появяват проблеми със стартирането или
производителността, сменете доставчиците или марката на горивото. Този
двигател е сертифициран за работа с бензин. Системата за контрол на емисиите
за карбураторни двигатели е EM (Модификации на двигателя). Системите за
контрол на емисиите за двигатели с електронно впръскване на горивото са ECM
(модул за управление на двигателя), MPI (многопортово впръскване) и, ако са
оборудвани, O2S (кислороден сензор).
Голяма надморска височина
При надморски височини над 5000фута (1524метра), позволеният бензин е
минимум 85октана/85AKI (89RON).
При карбураторни двигатели е необходимо регулиране за големи надморски
височини, за да се запази производителността. Работата без тази настройка ще
доведе до понижена производителност, по-голям разход на гориво и повишени
емисии. Свържете се с упълномощен сервизен представител на Briggs & Stratton
за информация относно регулирането за големи надморски височини. Не се
препоръчва работа на двигателя при надморска височина под 2500 ход (762м) с
направено регулиране за голяма надморска височина.
При двигатели с електронно впръскване на горивото (EFI) не е необходима
настройка за голяма надморска височина.
Доливане на гориво
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Когато добавяте гориво
Спрете двигателя. Преди да свалите капачката за гориво, изчакайте най-
малко две (2) минути, за да си гарантирате, че двигателят се е охладил.
Напълнете резервоара за гориво на открито или в помещение с добра
вентилация.
Не слагайте твърде много гориво в резервоара. За да оставите възможност
за разширение на горивото, не пълнете над долната част на гърлото на
резервоара за гориво.
Дръжте горивото далече от искри, открити пламъци, пилотни светлини,
топлина и други източници на запалване.
Често преглеждайте горивопроводите, резервоара за гориво, капачката
на горивото и връзките за наличие на пукнатини или течове. Подменете
повредените части.
Ако горивото се разлее, изчакайте, докато се изпари преди да стартирате
двигателя.
1. Почистете пространството около капачката на резервоара за гориво от
мръсотия и остатъци. Свалете капачката на резервоара за гориво.
2. Напълнете резервоара за гориво (A, фигура 6) с гориво. Тъй като горивото се
разширява, не пълнете над долната част на гърлото на резервоара (B).
3. Поставете обратно капачката за гориво.
Стартиране и спиране на двигателя
Стартиране на двигателя
ПРЕДУПРЕЖДЕНИЕ
Бързото изтегляне на въжето на стартера (откат) притегля дланта и ръката
Ви към двигателя по-бързо, отколкото Вие можете да я отдръпнете.
Това може да причини счупване на кости, фрактури, натъртвания или
навяхвания.
За да избегнете отката, при стартиране на двигателя, издърпайте бавно
въжето на стартера, докато усетите съпротивление, а след това дръпнете
рязко.
Изключете или премахнете всички външни товари на оборудването/
двигателя, преди да го стартирате.
Уверете се, че директно прикачените към двигателя елементи, като, но не
само остриета, крилни витла, лебедки и зъбни колела, трябва да бъдат
правилно прикрепени.
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Когато стартирате двигателя
Уверете се, че запалителната свещ, шумозаглушителят, капачката
на резервоара за гориво и въздушният филтър (ако има такива) са
монтирани правилно.
Не стартирайте двигателя без запалителна свещ.
Ако двигателят е задавен, поставете смукача (ако има такъв) в положение
ОТВОРЕНО или РАБОТА. Поставете прибора за управление на
дроселната клапа в положение БЪРЗО (ако има такъв) и въртете, докато
двигателят стартира.
Ако в областта има изтичане на природен газ или газ LP, не стартирайте
двигателя.
Не използвайте течности за начално запалване под налягане, защото
парите им са възпламеними.
ПРЕДУПРЕЖДЕНИЕ
ОПАСНОСТ ОТ ОТРОВНИ ГАЗОВЕ. Отработените газове от двигателя
съдържат въглероден оксид, отровен газ, който би могъл да Ви убие за
минути. Дори ако не усещате отработените газове, все още можете да
бъдете изложени на въздействието на отровен въглероден оксид. Ако
усетите гадене, замайване или слабост докато използвате този продукт,
ВЕДНАГА излезте на чист въздух. Отидете на лекар. Възможно е да сте
получили отравяне с въглероден окис.
Въглеродният окис може да се натрупва в затворени помещения.
Работете с този продукт САМО на открито, далече от прозорци, врати
и вентилационни отвори, за да намалите риска от натрупване на
въглероден окис.
Монтирайте сигнални уредби за наличие на въглероден оксид,
захранвани с батерии или чрез щепсел, според инструкциите на
производителя. Сигналните уредби за дим не могат да засичат
въглероден окис.
НЕ РАБОТЕТЕ с този продукт в домове, гаражи, мазета, непреходни
коридори, хангари или други затворени помещения, дори при използване
на вентилатори или при отворени врати и прозорци за вентилация. След
работата с този продукт, въглеродният окис може бързо да се натрупа в
тези помещения и да остане с часове.
ВИНАГИ поставяйте този продукт по посока на въздушното течение
и насочвайте изгорелите газове от двигателя далече от обитаваните
помещения.
ПРЕДУПРЕЖДЕНИЕ
Този двигател се доставя от Briggs & Stratton без масло. Производителите на
оборудването или търговците може да са добавили масло в двигателя. Преди
да стартирате двигателя за първи път, уверете се, че маслото е на правилното
ниво. Добавяйте масло, както е посочено в инструкциите в това ръководство. Ако
стартирате двигателя без масло, той ще се повреди и ремонтът няма да бъде
покрит от гаранцията.
Типове стартиращи системи
Преди стартиране на двигателя трябва да определите вида на стартиращата
система на двигателя Ви. Вашият двигател разполага с един от следващите по-
долу видове.
Система за електронно впръскване на горивото (EFI): Някоя EFI
система няма смукач или подкачваща помпа.
Система със смукач: Този тип система има смукач, който да бъде
използван при ниски температури. Някои модели притежават отделен
лост за смукача, докато други имат комбинация от смукач и ръчна газ.
Двигателят няма механично подкачване на горивото.
ЗАБЕЛЕЖКА:Вашето оборудване може да има прибори за дистанционно
управление. Вижте ръководството за работа за разположението и работата с
приборите за дистанционно управление.
Система за електронно впръскване на горивото (EFI)
1. Проверете моторното масло. Вижте раздел Проверка на нивото на
маслото.
2. Уверете се, че задвижващите управления на оборудването, ако има такива, са
изключени.
3. Завъртете кранчето за подаване на гориво (A, Фигура 7), ако има такова, до
позиция ОТВОРЕНА.
4. Преместете ръчната газ (B, Фигура 7), ако има такава, на позиция БЪРЗО.
Включете двигателя на положение за БЪРЗИ обороти.
16 vanguardpower.com
Not for
Reproduction
5. Завъртете ключа за електрическо стартиране (D, фигура 7) на позиция ВКЛ.
или СТАРТ.
ПРЕДУПРЕЖДЕНИЕИзползвайте кратки стартови цикли (най-много пет секунди)
за удължаване на живота на стартера. Изчакайте една минута между отделните
стартови цикли.
Ако двигателят не стартира след 3-4 опита, свържете се с местния търговец или
отидете на vanguardpower.com, или се обадете на 1-800-999-9333.
Система със смукач
1. Проверете моторното масло. Вижте раздел Проверка на нивото на
маслото.
2. Уверете се, че задвижващите управления на оборудването, ако има такива, са
изключени.
3. Завъртете кранчето за подаване на гориво (A, Фигура 7), ако има такова, до
позиция ОТВОРЕНА.
4. Преместете ръчната газ (B, Фигура 7), ако има такава, на позиция БЪРЗО.
Включете двигателя на положение за БЪРЗИ обороти.
5. Преместете лоста на смукача (C, фигура 7) или комбинацията смукач/ръчна
газ (B, C) до ЗАТВОРЕНА позиция.
ЗАБЕЛЕЖКА:За да стартирате двигателя, когато горивната система е суха, ще
Ви бъде необходимо допълнително време за развъртането му в положение със
смукач. Това дава време на горивната помпа да впръска гориво в системата.
6. Завъртете ключа с превключвател (D, фигура 7) на позиция ВКЛ. или СТАРТ.
7. Ако двигателят стартира, но не продължи да работи, поставете лоста на
смукача (C, фигура 7) на ОТВОРЕНА позиция, за да стартирате двигателя.
ПРЕДУПРЕЖДЕНИЕИзползвайте кратки стартови цикли (най-много пет секунди)
за удължаване на живота на стартера. Изчакайте една минута между отделните
стартови цикли.
8. Щом двигателят загрее, поставете лоста на смукача (C, Фигура7) на позиция
ОТВОРЕНА.
Ако двигателят не стартира след 3-4 опита, свържете се с местния търговец или
отидете на vanguardpower.com, или се обадете на 1-800-999-9333.
Спрете двигателя
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Не запушвайте карбуратора (ако има такъв) за да спрете двигателя.
1. При ръчна газ на позиция БАВНО, завъртете ключа за електрическо
стартиране (D, фигура 7) до позиция ИЗКЛ. Извадете ключа и го дръжте на
безопасно място, далече от обсега на деца.
2. След спирането на двигателя, завъртете кранчето за подаване на гориво (A,
фигура 7), ако има такова, до позиция ЗАТВОРЕНО.
Техническо обслужване
Информация за техническо обслужване
ПРЕДУПРЕЖДЕНИЕ
По време на поддръжката, ако е необходимо да наклоните уреда, уверете се, че
резервоарът за гориво, ако е монтиран на двигателя, е празен и че е изправен
откъм страната на запалващата свещ. Ако резервоарът за гориво не е празен,
може да изтече гориво и да причини пожар или експлозия. Ако двигателят е
наклонен в друга посока, той няма лесно да се стартира поради замърсяване с
масло или гориво на въздушния филтър или на запалителната свещ.
Ние Ви препоръчваме да посетите упълномощен сервизен представител на
Briggs & Stratton за всички операции по техническото и сервизното обслужване на
двигателя и резервните части.
ПРЕДУПРЕЖДЕНИЕ
Всички компоненти, използвани при производството на този двигател, трябва да
бъдат на мястото си за правилната му работа.
ПРЕДУПРЕЖДЕНИЕ
Случайна искра на двигателя може да причини токов удар или пожар, и може
да доведе до заплитане, травматична ампутация или разкъсване.
Преди да извършвате настройки или поправки:
Откачете кабела на запалителната свещ и го дръжте далече от нея.
Откачете кабела на отрицателната клема на акумулатора (само при
двигатели с електрически стартер).
Използвайте само правилните инструменти.
Когато проверявате за искра:
Използвайте одобрен тестер за свещи.
Не проверявайте за искра при извадена запалителна свещ.
Сервизно обслужване по контрола на вредните
емисии
За поддръжка, смяна или ремонт на устройствата и системите за контрол
на вредните емисии, се свържете с квалифициран ремонтен цех или техник,
ремонтиращ двигатели, които не се използват за транспортни цели. Все пак,
за „безплатно“ сервизно обслужване по контрола на вредните емисии, работата
трябва да бъде изпълнена от упълномощен представител на завода. Вижте
Отчетите по контрола на вредните емисии.
График за техническо обслужване
На интервали от 8 часа или ежедневно
Проверете нивото на моторното масло.
Почистете повърхностите около шумозаглушителя и приборите за
управление.
На интервали от 100 часа или годишно
Почистете или сменете въздушния филтър
1 2
.
Сменете моторното масло и филтъра.
Сменете масления филтър (ако има такъв).
Сменете запалителните свещи.
Проверете шумозаглушителя и искрогасителя.
Обслужете изпускателната система.
На интервали от 250 часа или годишно
Проверете луфтовете на клапаните. Регулирайте ги, ако е необходимо.
На интервали от 400 часа или годишно
Сменете въздушния филтър
2
.
Сменете горивния филтър.
Обслужете системата за охлаждане на въздуха
1
.
Почистете ребрата на масления радиатор
1
.
На интервали от 600 часа
Сменете защитния филтър, ако има такъв.
1
При наличие на запрашеност или носещи се в околното пространство отломки,
да се почиства по-често.
2
При всяка трета смяна на въздушния филтър, сменяйте вътрешния защитен
филтър (ако има такъв).
Система за електронно впръскване на горивото
(EFI)
Системата EFI наблюдава температурата и скоростта на двигателя, както
и напрежението на акумулатора, при стартиране и загряване на двигателя.
Системата не се нуждае от регулиране. Ако възникнат проблеми при стартирането
или работата, свържете се с упълномощен сервизен представител на Briggs &
Stratton.
ПРЕДУПРЕЖДЕНИЕУверете се, че следвате стъпките по-долу, в противен случай
системата EFI може да се повреди.
НЕ стартирайте двигателя при разхлабени кабели на акумулатора.
Преди да разедините, свалите и/или поставите акумулатора, завъртете
ключа до позиция ИЗКЛ.
НЕ използвайте зарядно устройство за акумулатора, за да стартирате
двигателя.
НЕ разкачвайте кабелите на акумулатора по време на работа на машината.
17
Not for
Reproduction
При разкачване на кабелите на акумулатора, първо свържете
положителния (+), а след това отрицателния (-) кабел.
Когато зареждате акумулатора, завъртете ключа на запалването до
позиция ИЗКЛ. и откачете отрицателния (-) кабел от акумулатора.
НЕ пръскайте вода директно върху електронния модул за управление.
Карбуратор и обороти на двигателя
Не правете настройки на карбуратора и оборотите на двигателя. Карбураторът
е заводски регулиран да работи ефикасно при повечето работни условия. Не
променяйте регулиращата пружина, лостчетата или други части, за да променяте
оборотите на двигателя. Ако се налагат някакви настройки се обърнете към
упълномощен сервизен представител на Briggs & Stratton за обслужване.
ПРЕДУПРЕЖДЕНИЕ
Производителят на оборудването определя максималните обороти за двигателя,
който е монтиран. Не превишавайте тези обороти. Ако не сте сигурни какви са
максималните обороти на оборудването или какви обороти са регулирани от
завода, свържете се с упълномощен сервизен представител на Briggs & Stratton за
помощ. За безопасна и правилна работа на оборудването, оборотите на двигателя
трябва да се регулират само от квалифициран сервизен техник.
Обслужване на запалителната свещ
Проверявайте искровата междина на запалителната свещ (A, фигура 8) с помощта
на измервателен прибор за кабели (B). Ако е необходимо, регулирайте искровата
междина на запалителната свещ. Монтирайте и затегнете запалителната свещ
с препоръчвания въртящ момент. За междината или въртящия момент, вижте
раздел Спецификации.
ЗАБЕЛЕЖКА:В някои райони според местното законодателство е задължително
да използвате резисторна запалителна свещ, за да се намалят сигналите при
запалване. Ако резисторната запалителна свещ е монтирана от производителя на
оборудването, използвайте същия тип за подмяна.
Обслужване на изпускателната система
ПРЕДУПРЕЖДЕНИЕ
По време на работа, двигателят и шумузаглушителят се нагорещяват. Ако
докоснете горещ двигател, може да се изгорите.
Запалимите материали, като листа, трева и сухи клонки, могат да се запалят.
Преди да докоснете двигателя или шумозаглушителя, спрете двигателя
и изчакайте две (2) минути. Уверете се, че е безопасно да докосвате
двигателя и шумозаглушителя.
Отстранете отпадъците от шумозаглушителя и двигателя.
Според Правилника на Калифорния за обществените ресурси, раздел 4442,
използването или работата с двигателя по залесени с гори, храсти или с треви
площи представлява нарушение, освен ако системата за отработени газове не
е снабдена с искрогасител, поддържан в ефикасно работно състояние, както е
определено в раздел 4442. Други щати или федерални юрисдикции могат да имат
подобни закони; за справка – Федерален регламент 36CFR, част261.52. Свържете
се с производителя, търговеца или продавача на оригинално оборудване, за да
получите искроуловител, проектиран за системата за отработени газове на този
двигател.
Премахнете остатъците от областта на шумозаглушителя и цилиндъра. Проверете
шумозаглушителя за пукнатини, корозия или друг вид повреда. Свалете
преградата или искрогасителя, ако има такива, и ги проверете за повреда или
запушване със сажди. Ако откриете повреда, монтирайте резервните части на
оборудването, преди да започнете работа.
ПРЕДУПРЕЖДЕНИЕ
Резервните части трябва да бъдат със същата конструкция и да се монтират в
същото положение, както оригиналните части. Другите части може да се повредят
или да се причини нараняване.
Смяна на маслото на двигателя
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
По време на работа, двигателят и шумузаглушителят се нагорещяват. Ако
докоснете горещ двигател, може да се изгорите.
Ако източвате маслото от горната тръба за пълнене на масло, резервоарът
за гориво трябва да бъде празен. Ако не е празен, може да изтече гориво и
да причини пожар или експлозия.
Преди да докоснете двигателя или шумозаглушителя, спрете двигателя
и изчакайте две (2) минути. Уверете се, че е безопасно да докосвате
двигателя и шумозаглушителя.
Отработеното масло е опасен отпадъчен продукт и трябва да се изхвърля
по подходящ начин. Да не се изхвърля с домакинските отпадъци. Свържете
се с местните власти, обслужващият център или представител за безопасно
депониране или рециклиране.
Раздел Източване на маслото
1. При ИЗКЛ., но все още топъл двигател, откачете кабела(ите) на
запалителната(ите) свещ(и) (D, фигура 9) и го(и) дръжте далече от
запалителната(те) свещ(и) (Е).
2. Извадете щеката на нивопоказателя (A, Фигура 10).
3. Свалете пробката от отвора за източване на маслото (F, фигура 11). Източете
маслото в подходящ контейнер.
4. Поставете и затегнете пробката за източване на маслото (F, Фигура 11).
Сменете масления филтър, ако има такъв
1. Източете маслото от двигателя. Вижте раздел Източване на маслото.
2. Свалете масления филтър (H, фигура 12) и го изхвърлете правилно.
3. Преди да поставите новия маслен филтър, леко намажете уплътнението му с
чисто масло.
4. Поставете масления филтър с ръка, докато уплътнението докосне адаптера
му, след товазатегнете масления филтърс 1/2 до 3/4 оборота.
5. Долейте масло. Вижте раздел Доливане на масло.
6. Двигателят трябва да се стартира и да работи. Докато двигателят загрява,
проверете за течове на масло.
7. Спрете двигателя. Уверете се, че нивото на маслото е до горната част на
индикатора за напълване (B, фигура 5) върху щеката.
Доливане на масло
Уверете се, че двигателят е разположен хоризонтално.
Почистете от всички отпадъци мястото около отвора за наливане на масло.
Вижте разделТехнически данниотносно вместимостта за маслото.
1. Извадете щеката на нивопоказателя (A, Фигура 10). С чиста кърпа почистете
маслото от щеката на нивопоказателя.
2. Бавно налейте масло в отвора за наливане на масло в двигателя (C, Фигура
10). Не препълвайте. Изчакайте една минута и отново проверете нивото на
маслото.
3. Поставете и затегнете щеката на нивопоказателя (A, Фигура 10).
4. Свалете нивопоказателя и проверете нивото на маслото. Коригирайте
нивото на маслото до горния белег за напълване (B, фигура 10) върху
нивопоказателя.
5. Поставете и затегнете щеката на нивопоказателя (A, Фигура 10).
6. Свържете кабела(ите) на запалителната(те) свещ(и) (D, фигура 9) със
запалителната(те) свещ(и) (E).
Обслужване на въздушния филтър
ПРЕДУПРЕЖДЕНИЕ
Изпаренията на горивата са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Не стартирайте и не работете с двигателя при демонтиран комплект на
въздушния филтър (ако има такъв) или със свален въздушен филтър (ако
има такъв).
ПРЕДУПРЕЖДЕНИЕ
Не използвайте сгъстен въздух или разтворители, за да почиствате филтъра.
Сгъстеният въздух може да причини повреда на филтъра, а разтворителите да го
разтворят.
Вижте Графика за техническото обслужване относно изискванията за
обслужване.
Различните модели използват хартиен филтър или филтър от пенопласт. Някои
модели са оборудвани и с предфилтър, който може да бъде измиван и повторно
използван. Сравнете илюстрациите в това ръководство с типа филтър, монтиран
на Вашия двигател и го обслужвайте, както следва.
Циклонен въздушен филтър
1. Отворете фиксатора(те) (A, фигура 13) и демонтирайте капака (B).
2. Свалете въздушния филтър (С, фигура 13).
3. Леко потупайте въздушния филтър върху твърда повърхност, за да изпаднат
остатъците. Ако въздушният филтър е замърсен, сменете го с нов.
4. За да свалите защитния филтър (D, фигура 13), ако има такъв, внимателно
го издърпайте от тялото на въздушния филтър (E). Уверете се, че
замърсяването или отпадъците не влизат в двигателя.
18 vanguardpower.com
Not for
Reproduction
5. Монтирайте новия защитен филтър (D, фигура 13) в тялото на въздушния
филтър (E).
6. Монтирайте въздушния филтър (C, фигура 13) върху защитния филтър (D).
7. Монтирайте капака (B, фигура 13) и затворете фиксатора(те) (A).
Нископрофилен въздушен филтър
1. Свалете фиксатора(те) (A, фигура 14).
2. Свалете капака (B, Фигура 14).
3. Свалете фиксатора(те) (C, фигура 14) и крепежния елемент (D).
4. Свалете въздушния филтър (Е, фигура 14).
5. Свалете предфилтъра (F, фигура 14), ако има такъв, от въздушния филтър
(Е).
6. За да освободите наслояванията, леко потупайте въздушния филтър (Е,
фигура 14) върху твърда повърхност. Ако въздушният филтър е замърсен,
сменете го с нов.
7. Почистете предфилтъра (F, фигура 14), ако има такъв, във воден разтвор
на почистващ препарат. Уверете се, че предфилтърът е напълно сух. Не
смазвайте предфилтъра.
8. Сглобете сухия предфилтър (F, фигура 14), ако има такъв, към въздушния
филтър (Е).
9. Монтирайте въздушния филтър (Е, фигура 14) и закрепете посредством
крепежния елемент (D) и фиксатора(те) (С).
10. Монтирайте капака (B, фигура 14) и го закрепете със фиксатора(те) (A).
Уверете се, че свързващата(ите) скоба(и) са стегнати.
Обслужване на системата за охлаждане
ПРЕДУПРЕЖДЕНИЕ
По време на работа, двигателят и шумузаглушителят се нагорещяват. Ако
докоснете горещ двигател, може да се изгорите.
Запалими отпадъци, като листа, трева и сухи клонки, могат да бъдат
запалени.
Преди да докоснете двигателя или шумозаглушителя, спрете двигателя
и изчакайте две (2) минути. Уверете се, че е безопасно да докосвате
двигателя и шумозаглушителя.
Отстранете отпадъците от шумозаглушителя и двигателя.
ПРЕДУПРЕЖДЕНИЕ
Не използвайте вода за почистване на двигателя. Водата може да причини
замърсяване на горивната система. Използвайте четка или суха кърпа, за да
почистите двигателя.
Това е двигател с въздушно охлаждане. Нечистотиите или отпадъците могат да
спрат въздушния поток и да причинят прегряване на двигателя, което води до
незадоволителни резултати и намалена продължителност на живота му.
1. Използвайте четка или суха кърпа, за да отстраните наслояванията от зоната
на отвора за въздух (A, фигура 15).
2. Пазете чисти лостовата система, пружините и приборите за управление (B,
фигура 15, 16).
3. Пазете пространството около и зад шумозаглушителя (C, фигури 15, 16) без
запалими наслоявания.
4. Убедете се, че ребрата за охлаждане на маслото (D, фигура 15) са почистени
от замърсяване и наслоявания.
5. Разхлабете фиксатора(те) (Е, фигури 15, 16) и премахнете панелите за достъп
до наслояванията (F). Отстранете тревите и остатъците от замърсявания,
които са се събрали върху цилиндрите.
6. Монтирайте панелите за достъп до замърсяванията (F, фигури 15, 16) и
закачете фиксатора(те) (E).
След известно време, могат да се съберат остатъци върху охладителните
ребра на цилиндъра и да доведат до прегряване на двигателя. Тези остатъци от
замърсявания не могат да се отстранят без частично разглобяване на двигателя.
Потърсете упълномощен сервизен представител на Briggs& Stratton за проверка и
почистване на въздушната охладителна система, както се препоръчва в Графика
за техническо обслужване.
Обслужване на горивната система
ПРЕДУПРЕЖДЕНИЕ
Горивото и неговите пари са възпламеними и взривоопасни. Пожар или
експлозия може да доведе до изгаряния или смърт.
Дръжте горивото далече от искри, открити пламъци, пилотни светлини,
топлина и други източници на запалване.
Често преглеждайте горивопроводите, резервоара за гориво, капачката
на горивото и връзките за наличие на пукнатини или течове. Подменете
повредените части.
Преди почистване или смяна на филтъра за гориво, източете резервоара
за гориво или затворете клапана за подаване на гориво.
Ако горивото се разлее, изчакайте, докато се изпари преди да стартирате
двигателя.
Резервните части трябва да бъдат със същата конструкция и да се
монтират в същото положение, както оригиналните части. Другите части
може да се повредят или да се причини нараняване.
Филтър за гориво, ако има такъв
1. Преди почистване или смяна на филтъра за гориво (А, фигура 17), източете
резервоара за гориво или затворете клапана за подаване на гориво. Ако
резервоарът за гориво не е източен, горивото може да изтече и да причини
пожар или експлозия.
2. Използвайте клещи, за да стиснете краищата (B, фигура 17) на скобите (C),
след това отстранете скобите от филтъра за гориво (A). Усучете и изтеглете
горивопроводите (D) от филтъра за горивото.
3. Проверете горивопроводите (D, фигура 17) за пукнатини или течове. Сменете
ги, ако е необходимо.
4. Заменете филтъра за гориво (A, фигура 17) с оригинален филтър за
еднократна употреба за оборудване.
5. Закачете горивопроводите (D, фигура 17) със скобите (С).
Складиране
Горивна система
Вижте фигурата: 18.
Поддържайте нивото на двигателя (нормално работно положение). Напълнете
резервоара за гориво (A, фигура 18) с гориво. За да се даде възможност за
топлинно разширение на горивото, не пълнете над гърлото на резервоара за
гориво (B).
Горивото може да остарее, ако се съхранява в контейнер повече от 30дни.
Всеки път, когато добавяте гориво в контейнера, добавяйтестабилизатор за
горивокъм горивото, както е посочено в инструкциите на производителя. Това
запазва свежестта на горивото и намалява свързаните с горивото проблеми или
замърсяване в горивната система.
Не е необходимо да източвате горивото от двигателя, когато,според
инструкциите, е добавенстабилизатор за гориво. Преди да приберете уреда,
ВКЛЮЧЕТЕ двигателя в продължение на 2минути, за да могат стабилизаторът за
гориво и горивото да преминат през цялата система.
Ако бензинът в двигателя не е бил обработван със стабилизатор за гориво, той
трябва да бъде източен в подходящ съд. Оставете двигателя да работи, докато
спре поради изчерпване на горивото. За да поддържате свежестта на горивото
при складирането му, препоръчваме използването на стабилизатор.
Масло на двигателя
Докато двигателят е все още топъл, сменете маслото. Вижте раздел Смяна на
двигателното масло.
Откриване и отстраняване на
неизправности
Съдействие
За помощ, се свържете с Вашия местен търговец или отидете на
vanguardpower.com , или се обадете по 1-800-999-9333 (в САЩ).
Спецификации
Спецификации и резервни части
Модели:540000 , 54E000
Работен обем 54.68куб. инча (896 куб. см)
Отвор 3.366 инча ( 85,5 мм)
Работен ход на буталото 3.071 инча (78,0 мм)
19
Not for
Reproduction
Модели:540000 , 54E000
Вместимост за масло 78 - 80унции (2,3 - 2,4л)
Искрова междина на запалителната
свещ
.030 инча (,76 мм)
Въртящ момент за затягане на
запалителната свещ
180 фунт-инч (20 Nm)
Въздушна междина между ротора и
статора
.005 - .008 инча (,13 - ,20 мм)
Междина на всмукателния клапан .004 - .006 инча (,10 - ,15 мм)
Междина на изпускателния клапан .007 - .009 инча (,18 - ,23 мм)
Модели: 610000, 61E000, 61G200, 61G300
Работен обем 60.60куб. инча (993 куб. см)
Отвор 3.366 инча ( 85,5 мм)
Работен ход на буталото 3.406 инча (86,5 мм)
Вместимост за масло 78 - 80унции (2,3 - 2,4л)
Искрова междина на запалителната
свещ
.030 инча (,76 мм)
Въртящ момент за затягане на
запалителната свещ
180 фунт-инч (20 Nm)
Въздушна междина между ротора и
статора
.005 - .008 инча (,13 - ,20 мм)
Междина на всмукателния клапан .004 - .006 инча (,10 - ,15 мм)
Междина на изпускателния клапан .007 - .009 инча (,18 - ,23 мм)
Резервни части – Модели: 540000,
54E000, 610000, 61E000, 61G200, 61G300
Резервна част Номер на частта
Циклонен въздушен филтър (фигура
13)
841497
Циклонен защитен филтър (фигура
13)
821136
Въздушен филтър, нисък профил
(фигура 14)
692519
Предфилтър, нисък профил (фигура
14)
692520
Масло – SAE30 100028
Маслен филтър 842921
Филтър за гориво 691035
Резисторна запалителна свещ 491055
Дълготрайна запалителна свещ с
платинена сърцевина
5066
Ключ за запалителната свещ 19374
Искров тестер 19368
Мощността на двигателя намалява с 3,5% на всеки 1000 фута (300 метра) над
морското ниво и с 1% за всеки 10°F (5,6°C) над 77°F (25°C). Двигателят ще
работи задоволително при наклон до 15°. Вижтеръководството за употреба на
оборудването за допустимите, безопасни граници за работа по наклони.
Номинална мощност
Общата номинална мощност за отделните модели бензинови двигатели се
определя в съответствие с код J1940 от Процедура за оценка на мощността и
въртящия момент на малки двигатели на SAE (Асоциация на автомобилните
инженери) и се оценява в съответствие със SAE J1995. Стойностите на въртящия
момент са отчетени при 2600об./мин. за двигателите, чиито „об./мин.“ са
посочени на етикета, и при 3060об./мин. за всички останали; мощностите в конски
сили са отчетени при 3600об./мин. Кривите на общата мощност могат да се
видят на: www.BRIGGSandSTRATTON.COM. Стойностите на нетната мощност
са отчетени при инсталирани системи за отделяне на изгорели газове и за
очистване на въздуха, докато стойностите на общата мощност се отчитат без тези
прикачни устройства. Действителната обща мощност на двигателя е по-висока
от нетната мощност и зависи, освен всичко друго, от условията на работната
среда, както и от специфичните особености на всеки двигател. Имайки предвид
голямото разнообразие от устройства, на които се инсталират такива двигатели,
бензиновият двигател може да не е в състояние да развива общата номинална
мощност, когато се използва в даден вид оборудване. Тези разлики се дължат
на различни фактори, включително, но без ограничение до разнообразните
компоненти на двигателите (системи за очистване на въздуха, за отделяне на
изгорели газове, за зареждане, за охлаждане, карбуратор, горивна помпа и
др.), ограничения на приложението, условия на работната среда (температура,
влажност, надморска височина), както и от специфичните особености на всеки
двигател. Вследствие на ограниченията за производство и капацитет, Briggs
& Stratton може да замести този двигател с двигател с по-висока номинална
мощност.
Гаранция
Гаранция за двигателите Briggs & Stratton
В сила от януари 2019г.
Ограничена гаранция
Фирма Briggs & Stratton гарантира, че по време на указания по-долу гаранционен
период ще поправя или заменя безплатно всяка част, оказала се дефектна по
отношение на материалите или изработката, или и двете. Транспортните разходи
за изпратения за ремонт или за замяна продукт по тази гаранция трябва да бъдат
поети от клиента. Тази гаранция е валидна за определения срок и се подчинява
на изложените по-долу условия. За гаранционното обслужване намерете най-
близкия упълномощен сервизен представител в нашата указателна карта на адрес
BRIGGSandSTRATTON.COM. Потребителят трябва да се свърже с упълномощен
сервизен представител, на когото да предостави продукта за оглед и изпитване.
Няма друга изрична гаранция. Подразбиращите се гаранции, включително
тези за годност за продажба и за определено предназначение, са ограничени
до посочения по-долу гаранционен срок или до степента, разрешена от
закона. Отговорността за непредвидени или закономерно настъпили повреди
са изключени до степента на изключване, позволена от закона. Някои щати или
държави не допускат ограничения за срока на валидност на подразбиращи се
гаранции. Също така някои щати или държави не позволяват изключване или
ограничаване на отговорността за случайни или закономерно настъпили повреди,
така че горното ограничение и изключване може да не се отнася за Вас. Тази
гаранция Ви дава специфични законови права, а вие можете да имате и други
такива, които са различни в отделните щати и в отделните държави
4
.
Стандартни гаранционни условия
1, 2, 3
Vanguard®; Търговска серия
3
Лична употреба - 36месеца
Търговска употреба - 36месеца
СерияXR
Лична употреба - 24месеца
Търговска употреба - 24месеца
Всички други двигатели с чугунена риза Dura-Bore™
Лична употреба - 24месеца
Търговска употреба - 12месеца
Всички други двигатели
Лична употреба - 24месеца
Търговска употреба - 3месеца
1
Това са нашите стандартни гаранционни условия, но е възможно
понякога да има допълнително гаранционно покритие, което не е
било определено към момента на публикуването на този документ. За
списък на текущите гаранционни условия за Вашия двигател посетете
BRIGGSandSTRATTON.com или се обърнете към Вашия оторизиран
сервизен представител на Briggs & Stratton.
2
Няма гаранция за двигатели, монтирани на оборудване, ползвано като
източник на първична мощност вместо централно захранване; резервни
генератори, ползвани за търговски цели, сервизни автомобили с мощност
над 25к.с. или двигатели, използвани за състезания, за търговски цели или
за отдаване под наем.
3
Vanguard инсталиран на резервни генератори: 24месеца за лична
употреба, няма гаранция при търговска употреба. Търговски серии с дата на
производство преди м.юли 2017г.: 24месеца за лична употреба, 24месеца
за търговска употреба.
4
За Австралия - Нашите стоки се доставят с гаранции, които не могат да се
изключват по силата на австралийското законодателство за потребителите.
При сериозен дефект имате право на замяна или възстановяване на сумата,
както и на компенсация за всяка друга нормално предвидима загуба или
повреда. Също така имате право на ремонт или замяна на стоката, в случай
че тя не е с приемливо качество и повредата не може да се квалифицира
като сериозен дефект. За гаранционното обслужване намерете най-
близкия упълномощен сервизен представител в нашата указателна карта
на BRIGGSandSTRATTON.COM или се обадете на 1300274447, изпратете
имейл или пишете на [email protected], Briggs &
Stratton Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW, Australia,
2170.
Гаранционният срок започва да тече от първоначалната дата на закупуване от
първия потребител на дребно или потребител за търговски цели. „Потребителска
употреба“ означава употреба за лични и домашни цели от краен потребител.
„Търговска употреба“ означава всеки друг вид употреба, включително за търговски
20 vanguardpower.com
Not for
Reproduction
1 / 1

Simplicity 540477-2220-G1 Používateľská príručka

Kategória
Motor
Typ
Používateľská príručka