Parkside AFS 550 A1 Návod na používanie

AIRLESS PAINT SPRAYER/ AIRLESS-FARBSPRÜH-

SYSTEM / PISTOLET À PEINTURE AIRLESS PAFS 550 A1

PISTOLET À PEINTURE AIRLESS

Traduction des instructions d’origine

AIRLESS-FARBSPRÜHSYSTEM

Originalbetriebsanleitung

AIRLESS PAINT SPRAYER

Translation of the original instructions

AIRLESS STŘÍKACÍ SYSTÉM

NA BARVU

Překlad originálního provozního návodu

AIRLESS-VERFSPUITSYSTEEM

Vertaling van de originele gebruiksaanwijzing

AIRLESS STRIEKACÍ SYSTÉM

NA FARBU

Preklad originálneho návodu na obsluhu

SYSTEM DO ROZPYLANIA

FARBY AIRLESS

Tłumaczenie oryginalnej instrukcji obsługi

SISTEMA DE PULVERIZACIÓN

DE PINTURA AIRLESS

Traducción del manual de instrucciones original

AIRLESS FARVESPRØJTESYSTEM

Oversættelse af den originale driftsvejledning

IAN 360098_2010

GB Translation of the original instructions Page 1

DE Originalbetriebsanleitung Seite 19

FR Traduction des instructions d’origine Page 39

NL Vertaling van de originele gebruiksaanwijzing Pagina 61

CZ Překlad originálního provozního návodu Strana 81

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 101

SK Preklad originálneho návodu na obsluhu Strana 121

ES Traducción del manual de instrucciones original Página 141

DK Oversættelse af den originale driftsvejledning Side 161

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l‘appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas

las funciones del dispositivo.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

A B

C D E

F G

H I

J

PAFS 550 A1 GB│IE │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Equipment ..........................................................................2

Package contents ....................................................................3

Technical speciﬁcations ...............................................................3

General power tool safety warnings .......................................4

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Service ..........................................................................5

Additional safety instructions .............................................6

Safety instructions for the high- pressure hose ...............................................8

Original accessories/attachments .......................................................8

Working procedures ....................................................9

Before use ............................................................. 9

Assembly ..........................................................................9

Selecting/changing the nozzle .........................................................9

Replacing the HEA ﬁlter ..............................................................10

Use ..................................................................10

Settings ...........................................................................11

Spraying ..........................................................................11

Overheating protection ..............................................................11

Depressurising the appliance ..........................................................11

Eliminating suction problems ..........................................................12

Blow out the nozzle .................................................................12

Work breaks .......................................................................12

Shutting down, maintenance and cleaning .................................12

Cleaning the inlet valve ..............................................................14

Cleaning the connecting thread ........................................................14

Storage and transportation ...........................................................14

Troubleshooting .......................................................15

Disposal .............................................................. 15

Kompernass Handels GmbH warranty ....................................16

Service ............................................................... 17

Importer .............................................................17

Original declaration of conformity ........................................18

PAFS 550 A1

■ 2 │ GB│IE

AIRLESS PAINT SPRAYER

PAFS 550 A1

Introduction

Congratulations on the purchase of your new appli-

ance. You have selected a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all operating and

safety instructions. Use the product only as de-

scribed and for the range of applications speciﬁed.

Please also pass these operating instructions on to

any future owner.

Intended use

This appliance is designed for painting indoor

walls as well as outdoor objects. Permissible

materials for use include:

– water-based paints and varnishes.

Do not use for:

- Flammable coatings, materials containing acetone

or nitro thinners,

- Materials that contain highly abrasive components,

- Facade paint, lyes and acidic coating materials.

Do not use the appliance in areas where there is

a risk of explosion.

Any other usage or modiﬁcation of the appliance

is deemed to be improper and carries a signiﬁcant

risk of accidents. The manufacturer accepts no

responsibility for damage(s) resulting from improper

usage. This appliance is intended for domestic use

only.

Equipment

See illustrations on the fold-out page

1 Return hose

2 Suction hose

3 Pressure regulator dial

4 Storage compartment for nozzles and

HEA ﬁlters

5 Nozzle

6 Safety catch

7 Paint spray gun

8 Handle

9 Trigger

0 Connecting thread for paint spray gun

q HEA ﬁlter

w High-pressure hose

e Function switch

r Connecting thread

t Intake ﬁlter

z Valve trigger

u Filter plate

i Plastic ring

o Holder

p Nozzle chamber

a Nozzle holder

s Spring

d Washer

f Ball

g O-ring

h Inlet valve

j Fastening screw

k Hex screw

l Hose clips

PAFS 550 A1 GB│IE │ 3 ■

Package contents

1 airless paint sprayer

1 paint spray gun

1 intake hose, 1 m, (pre-ﬁtted)

including return hose

1 high-pressure hose, 9 m

1 white HEA ﬁlter (pre-ﬁtted)

1 yellow HEA ﬁlter

2 nozzles 311 and 517* (*pre-ﬁtted)

1 set of operating instructions

Technical speciﬁcations

Motor unit

Rated voltage 230 V ∼, 50 Hz

(AC)

Rated power consumption 550 W

Max. paint ﬂow rate 1250 ml/min

Max. working pressure 110bar

Max. temperature of

coating material 40°C

Protection class I

Protection rating IPX3 Protection

against water spray,

up to 60° compared

to normal operating

position

Paint spray gun

Max. surface temperature 43°C

Max. temperature of

coating material 40°C

Noise and vibration data

Noise measurement value determined in accord-

ance with EN62841. The A-rated noise level of

the power tool is typically:

Sound pressure level LpA = 88 dB (A)

Uncertainty K = 3 dB

Sound power level LWA = 101 dB (A)

Uncertainty K = 3 dB

Noise measurement value determined in accord-

ance with EN14462. The rated noise level of the

paint spray gun is typically:

Sound pressure level LpA = 78.4 dB

Uncertainty K = 2.5 dB (A)

Sound power level LWA = 91.2 dB

Uncertainty K = 2.5 dB (A)

Wear ear muﬀs!

Total vibration value of the

handle ah < 5.1 m/s2

Uncertainty K = 1.5 m/s2

Symbols on the appliance

Always wear safety goggles.

Always wear a mask.

Always wear ear muﬀs.

Always wear conductive protective gloves.

Wear non-slip, conductive safety shoes.

Wear protective clothing.

NOTE

► The vibration emission values and the noise

emission values given in these instructions

have been measured in accordance with a

standardised test procedure and can be used

for comparison of the power tool with another

tool.

► The speciﬁed total vibration values and the

noise emission values can also be used to

make a provisional load estimate.

PAFS 550 A1

■ 4 │ GB│IE

WARNING!

► Depending on the manner in which the power

tool is being used, and in particular the kind

of workpiece being worked, the vibration and

noise emission values can deviate from the

values given in these instructions during actual

use of the power tool.

► Try to keep the vibration load as low as

possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the

working time. Wherein all states of operation

must be included (e.g. times when the power

tool is switched oﬀ and times where the power

tool is switched on but running without load).

General power tool

safety warnings

WARNING!

►Read all safety warnings, instructions, illus-

trations and speciﬁcations provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When working outdoors with an electrical

power tool always use extension cords that

are also suitable for use outdoors. Use of a

cord suitable for outdoor use reduces the risk

of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD re-

duces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating a power tool may result in serious

personal injury.

b) Use

personal protective equipment. Always

wear safety goggles. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat

or hearing protection used for appropriate

conditions will reduce personal injuries.

PAFS 550 A1 GB│IE │ 5 ■

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power

tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not allow yourself to get lulled into a false

sense of security and do not ignore the safety

regulations for power tools, even if you are

familiar with the power tool after repeated

use. A careless action can cause severe injury

within a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that can-

not be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detacha-

ble, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool acci-

dentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits,

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in

unexpected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

PAFS 550 A1

■ 6 │ GB│IE

Additional safety instructions

RISK OF EXPLOSION AND FIRE!

► Make sure there are no ignition sources in the

vicinity. There is a risk of explosion due to the

potential formation of an explosive atmos-

phere in combination with ignition sources

(e.g. by electrostatic discharge, electric

sparks, hot surfaces)!

■RISK OF INJURY! DUE TO MISUSE! Do not

point the appliance towards people or animals.

■RISK OF EXPLOSION/FIRE! SMOKING

PROHIBITED! Do not cause any sparks or

ignite a naked ﬂame. Make sure there are no

ignition sources in the vicinity, such as open

ﬁres, smoking cigarettes, cigars and tobacco

pipes, sparks, glowing wires, hot surfaces, etc.

WARNING!

► Keep your distance from the nozzle tip!

■Do not spray yourself, other people or ani-

mals. Keep your hands and other body parts

out of the spray jet. If the spray jet pierces your

skin, seek medical assistance immediately. The

sprayed material can even penetrate through a

glove and into the skin and thus into your body.

■Do not treat an injection wound as a simple

cut. A high-pressure jet can inject toxins into

the body and cause serious injuries (e.g.

necrosis, loss of limbs). In the event of a chemi-

cal penetration of the skin, seek medical assis-

tance immediately.

■ Before each use, the following points must be

observed in accordance with the operating

instructions:

1) Do not use an appliance if it is faulty.

2) Secure the hand spray gun against acciden-

tal activation using the safety catch on the

trigger.

3) Ensure earthing – The connection must be

made via a properly earthed safety socket

(Schuko).

4) Check the maximum permissible operating

pressure of the high-pressure hose and spray

gun.

5) Check all connections for leaks.

■ Strictly follow the instructions on regular cleaning

and maintenance of the appliance. Observe the

following rules before carrying out any work on

the appliance and at every work break:

1) Depressurise the spray gun and the

high-pressure hose.

2) Secure the hand spray gun against acciden-

tal activation using the safety catch on the

trigger.

3) Switch oﬀ the appliance.

■Do not use the appliance in areas that fall

under the explosion protection ordinance.

■Keep your work area clean, well lit and free

of paint and solvent containers, cloths and

other inﬂammable materials. Possible risk of

spontaneous combustion. Make sure you have

functional ﬁre extinguishers available at all

times.

■Do not spray or clean with materials whose

ignition point is lower than 21°C. Use water-

based materials, non-volatile hydrocarbons

or similar materials. The evaporation of volatile

solvents will cause an explosive environment.

■Do not spray near ignition sources such as

static electric sparks, open

ﬂames, ignition

ﬂames, hot items

, motors, cigarettes or sparks

caused by plugging in/unplugging power

cables or by operating switches. These kinds

of ignition sources could ignite a ﬁre in the envi-

ronment.

■Do not spray any material if you do not know

whether it is potentially dangerous. Unknown

materials can cause hazards.

■ To avoid potential risks, damaged mains cables

should be replaced by the manufacturer, their

customer service department or someone simi-

larly qualiﬁed.

PAFS 550 A1 GB│IE │ 7 ■

■Wear additional personal protective equip-

ment such as suitable gloves and a protective

mask/respirator when spraying or when hand-

ling chemicals. Wearing appropriate protective

equipment for the conditions reduces your expo-

sure to dangerous substances.

■Be aware of the potential hazards of the

sprayed material. Follow the markings on the

container and the manufacturer’s information

on the spray material you are using, including

the instructions to use personal protective

equipment. Follow the manufacturer’s instruc-

tions to reduce the risk of ﬁre and injuries

caused by poisons, carcinogens, etc.

■ The spray gun must not be used for spraying

ﬂammable substances. Do not clean spray guns

with ﬂammable solvents.

■ Secure the appliance and the spray gun.

■ Secure all hoses, connections and ﬁlter parts

before starting up the spray pump. Unsecured

parts can come loose with great force or ﬂuid

can escape at high pressure, causing serious

injury. Always secure the spray gun when as-

sembling or disassembling the nozzle and dur-

ing any breaks in work.

■ Be prepared for recoil from the spray gun during

operation. At high operating pressure, pulling

the trigger causes a recoil force of up to 15 N.

If you are not prepared for this, your hand may

be pushed back or you may lose your balance.

This can lead to injuries. Continuous exposure

to this recoil can lead to permanent damage to

health.

■Max. operating pressure: the permissible oper-

ating pressure for the spray gun, high-pressure

hose and spray gun accessories must not be

less than the maximum operating pressure of

110 bar (11 MPa) indicated on the appliance.

■ The appliance must be connected via a properly

earthed safety socket (Schuko). The connection

must be equipped with a residual current device

INF≤30mA.

■ Make sure that the mains supply being connected

corresponds to the values indicated on the type

plate.

■ Before carrying out any work on the appliance,

relieve the pressure and disconnect the mains

plug from the socket.

■ You must earth the object that you are intending

to spray!

■ Observe the user manual when installing,

maintaining and repairing the appliance.

■ The appliance must be earthed during installa-

tion.

■Ensure adequate ventilation in the spray area

and suﬃcient fresh air in the entire room.

Wear a mask!

■ Always wear suitable safety goggles to keep

hazardous vapours and liquids away from

your eyes.

■ Wear protective clothing to keep paint away

from your skin and hair.

WARNING!

► Under certain circumstances, the ﬂow rate of

the coating material may cause electrostatic

charges to occur on the appliance during

spraying. They can cause sparks or ﬂames

when discharged. Therefore, make sure that

the appliance is always earthed via the elec-

trical installation. The connection must be

made via a properly earthed safety socket

(Schuko).

► Pay attention to the hazards that may be

caused by the sprayed substance and also

observe the labels on the containers or the

instructions given by the manufacturer of the

substance.

► When working indoors:

Ensure that no vapours containing solvents

form in the area around the appliance. Place

the appliance on the side facing away from

the spray object. Keep a minimum distance of

5 m between the motor unit and the spray gun.

PAFS 550 A1

■ 8 │ GB│IE

WARNING!

► When working outdoors:

Do not allow vapours containing solvents to

drift towards the appliance. Pay attention to

the wind direction! Position the appliance so

that no vapours containing solvents can reach

and build up around the appliance. Keep a

minimum distance of 5 m between the appli-

ance and the spray gun.

► There is a risk of a short-circuit if water pene-

trates the appliance! Never clean the appli-

ance with a high-pressure or steam cleaner.

► Do not use a solvent container with a small

opening to clean the appliance. An explosive

atmosphere could form. Earth the container

beforehand.

Safety instructions for the high-

pressure hose

DANGER!

■ Caution: Risk of injury from injection! Leaks

can develop in the high-pressure hose due to

wear, kinking and improper use. Fluid from

the leak can be injected into the skin.

■ The electrostatic charge from the spray gun and

high-pressure hose is discharged via the

high-pressure hose.

■ Check the high-pressure hose thoroughly before

each use.

■ Never pull on the high-pressure hose to move

the appliance.

■ Never try to repair a defective high-pressure

hose yourself!

■ Replace a damaged high-pressure hose immedi-

ately.

■ Avoid sharp bending or kinking; the smallest

bending radius is about 20 cm.

■ Protect the high-pressure hose from sharp

objects and edges.

■ Never twist the high-pressure hose.

■ Do not immerse the high-pressure hose in sol-

vent. Wipe the outside only with a soaked cloth.

■ Route the high-pressure hose so that there is no

risk of tripping.

■ Do not drive over the high-pressure hose.

NOTE

► The risk of damage increases with old high-

pressure hoses. We recommend replacing the

high-pressure hose every 6 years.

Original accessories/attachments

WARNING!

► Do not use any accessories that are not rec-

ommended by PARKSIDE. You can order

spare parts and accessories from the tele-

phone numbers given in the section "Service".

RESIDUAL RISKS!

When using the tool, additional residual risks may

occur that are not listed in the enclosed safety

instructions. These risks can arise from misuse,

prolonged use, etc.

Even if you follow the relevant safety regulations

and use safety equipment, certain residual risks

cannot be avoided.

These include:

■ Lung damage, if no suitable breathing protec-

tion is worn;

■ Hearing damage, if hearing protection is not

worn;

■ Eye damage, if suitable eye protection is not

worn;

■ Damage to health due to swinging of your

hands and arms during prolonged operation of

the appliance or if the appliance is not properly

held or maintained. If you use an appliance for

a long period of time, take regular breaks.

PAFS 550 A1 GB│IE │ 9 ■

WARNING! HAZARDS CAUSED

BY MATERIALS AND SUBSTANCES!

► There is a risk of coming into contact with or

absorbing coating materials and/or cleaning

ﬂuids. There is also a risk of inhaling vapours

from liquids. This can cause permanent dam-

age under certain conditions.

► Always wear personal protective equipment

when working on the appliance!

► Ensure suﬃcient technical or natural ventila-

tion.

► Follow the manufacturers’ safety instructions

for the respective coating materials and

cleaning liquids.

► If you experience any symptoms, seek medi-

cal advice!

Working procedures

NOTE

► Ensure that the spray material and thinning

agent are compatible. Using an unsuitable

thinning agent may cause clots that clog the

appliance.

► To ﬁnd out which thinning agent is suitable

for your spray material (water, paint thinner),

refer to the manufacturer's notes provided

with the spray material.

► Granular products and products containing

solids must not be sprayed. Their abrasive

eﬀect will shorten the service life of the

appliance.

Preparing the spray surface

WARNING!

► Risk of electric shock due to penetrating spray

material! Be sure to mask any sockets and

switches.

♦ Cover any surfaces around the spray area ex-

tensively and thoroughly. Any surface that is

not masked could become contaminated.

♦ Make sure that the spray surface is clean, dry

and free of grease.

♦ Polished surfaces should be lightly sanded and

the sanding dust removed.

Spraying technique

♦ Always hold the paint spray gun at the same

distance and at a right angle to the object. The

ideal spraying distance is approx. 20–25cm.

Move the paint spray gun evenly with your

whole arm (see ﬁg. J).

♦ Determine the appropriate settings in each

case by experimenting, e.g. on a piece of

cardboard.

♦ Do not switch the appliance on/oﬀ above the

spray area, but start and stop the spraying

process approx. 10 cm outside the spray area.

Before use

Assembly

NOTE

► You can assemble the appliance using two

adjustable spanners (not supplied).

► Alternatively, you can also use a 16mm and

19mm wrench (not supplied).

♦ Fit the high-pressure hosew onto the connect-

ing thread r on the appliance. Tighten the nut

using an adjustable spanner. Counter the nut

of the connection thread r with a second ad-

justable spanner (see ﬁg. A).

♦ Fit the other end of the high-pressure hose w

to the connecting thread of the paint spray

gun0. Tighten the nut using an adjustable

spanner. Counter the nut of the connection

thread of the paint spray gun with a second

adjustable spanner.

Selecting/changing the nozzle

Nozzle Use

Nozzle 311 low viscosity spray material

Nozzle 517 viscous spray material

♦ Insert the corresponding nozzle5 with the

arrow tip in the spraying direction into the

nozzle chamberp.

PAFS 550 A1

■ 10 │ GB│IE

Replacing the HEA ﬁlter

WARNING!

► The system must be depressurised in order

to carry out the following work. To do this,

follow the instructions in the section "Depres-

surising the appliance".

♦ Remove the high-pressure hosew from the

paint spray gun7.

♦ Turn the handle8 clockwise until the upper

end can be detached from the paint spray

gun7 (see ﬁg. B). You can attach an adjusta-

ble spanner to the lower end of the handle to

help.

♦ Insert the appropriate HEA ﬁlter q for the

installed nozzle 5:

–white HEA ﬁlter (pre-ﬁtted): nozzle 517

–yellow HEA ﬁlter: nozzle 311

♦ Turn the handle8 anticlockwise back into the

thread of the paint spray gun7.

NOTE

► Clean the HEA ﬁlters q regularly and re-

place them, if necessary. You can obtain

replacement ﬁlters from the service hotline

given in the section "Service".

Use

♦ Place the suction hose2 and return hose1

in the paint bucket.

♦ Press the valve trigger z to ensure that the

valve is free of any blockages.

♦ Insert the plug into a mains power socket.

♦ Turn the function switche to the vertical posi-

tion (PRIME).

♦ Turn the pressure regulator dial3 to position

2 to ensure that the paint is pumped through

the system.

♦ Wait until the paint runs through the return

hose1 back into the paint bucket. Turn the

pressure regulator dial3 to position 0 (oﬀ).

NOTE

► If no paint comes out, follow the measures

described in the section "Eliminating suction

problems".

♦ Turn the function switche to the horizontal

position (SPRAY).

♦ Turn the pressure regulator dial3 to a level

corresponding to the viscosity of the sprayed

material.

♦ Hold the paint spray gun 7 over an empty

container.

♦ Unlock the paint spray gun7 by turning the

safety catch6 so that its tip is facing down.

♦ Pull the trigger9 until the paint comes out in

a straight stream.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

PAFS 550 A1 GB│IE │ 11 ■

Settings

♦ You can use the pressure regulator dial3 to

switch the appliance on by setting a level greater

than 0. The level you choose depends on the

spray material used. Determine the best setting

by carrying out a spray test.

♦ The function switche has two settings:

–1. PRIME (vertical position):

This setting allows you to pre-ﬁll the system

with paint or to depressurise the appliance.

–2. SPRAY (horizontal position):

You can use this setting to work with the

appliance.

Spraying

♦ Unlock the paint spray gun7 by turning the

safety catch6 so that its tip is facing down.

♦ To spray, press the trigger9 and hold it down.

♦ To stop spraying, release the trigger9 again.

WARNING!

► Always secure the paint spray gun7 while

you are not actually spraying.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

Overheating protection

The appliance has an overheating protection.

It switches the appliance oﬀ if overheating is

imminent. If this happens, carry out the following

steps:

♦ Turn the pressure regulator dial3 to position 0

(oﬀ).

♦ Turn the function switche to the vertical

position (PRIME).

♦ Let the appliance cool down for at least

30 minutes and, if necessary, remove the cause

of the overheating. This could be, for example,

an item that is covering the ventilation slots or if

the appliance is too close to a wall.

♦ Put the appliance back into operation.

Depressurising the appliance

Always depressurise the appliance when you want

to take it out of operation. Depressurise the system

as follows:

♦ Turn the pressure regulator dial3 to position 0

(oﬀ).

♦ Turn the function switche to the vertical posi-

tion (PRIME).

♦ Unlock the paint spray gun7 by turning the

safety catch6 so that its tip is facing down.

♦ Release the pressure by pulling the trigger9.

Hold the paint spray gun7 over an empty

container while doing so.

♦ Wait until all pressure and paint has been

dispelled from the system. To stop spraying,

release the trigger9 again.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

PAFS 550 A1

■ 12 │ GB│IE

Eliminating suction problems

♦ Press the valve triggerz 3–4 times to remove

any blockages or deposits from the valve.

♦ If the problem persists: tap the connecting

threadr several times extremely carefully with

a rubber mallet (see ﬁg. I) to loosen harder

deposits.

Blow out the nozzle

WARNING!

► Always secure the paint spray gun7 while

you are not actually spraying.

♦ Turn the inserted nozzle5 180 degrees to-

wards the rear (see ﬁg. D).

If the nozzle cannot be turned, try depressuris-

ing the appliance.

♦ Press the trigger9 to blow out the nozzle5.

Hold the paint spray gun7 over an empty

container while doing so. As soon as a

straight spray jet comes out, the nozzle5 is

blown out.

♦ Turn the inserted nozzle5 180 degrees

towards the front.

NOTE

► Use an appropriate HEA ﬁlterq to minimise

blockages.

Work breaks

♦ Depressurise the appliance.

♦ Turn the pressure regulator dial3 to position 0

(oﬀ).

♦ Remove the plug from the mains socket.

♦ Place the paint spray gun7 in a plastic bag,

which you then seal airtight.

♦ Wet the paint in the paint bucket with water

so that no skin forms on the top.

Shutting down, maintenance

and cleaning

ATTENTION!

► Do not use ﬂammable materials such as nitro

thinners for cleaning.

► Please refer to the manufacturer’s information

of the respective spray material to ﬁnd out

which cleaning agents are suitable.

NOTE

► Thorough cleaning directly after every use is

very important for safety and operation.

Otherwise, the proper functioning of the

appliance can no longer be guaranteed.

► Wear suitable protective gloves during

cleaning work.

► Remove coating material residues at appro-

priate intervals. Remove any sprayed material

that has got onto unwanted surfaces before it

dries.

♦ Depressurise the appliance.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

♦ Unscrew the nozzle holdera from the paint

spray gun7.

♦ Place the suction hose2 together with the

return hose1 in a container with water or

a suitable cleaning agent.

♦ Turn the function switch to the horizontal posi-

tion (SPRAY).

♦ Turn the pressure regulator dial3 to position 5.

♦ Unlock the paint spray gun7 by turning the

safety catch6 so that its tip is facing down.

♦ Drain oﬀ the remaining paint by pulling the

trigger 9. Hold the paint spray gun7 over a

paint bucket while doing so.

PAFS 550 A1 GB│IE │ 13 ■

ATTENTION!

► If you are using a metal container, earth the

paint spray gun7 beforehand.

♦ Release the trigger9 as soon as the cleaning

ﬂuid starts ﬂowing out.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

♦ Turn the function switche to the vertical

position (PRIME).

♦ Unlock the paint spray gun7 by turning the

safety catch6 so that its tip is facing down.

♦ Drain oﬀ the remaining paint by pulling the

trigger9. Hold the paint spray gun7 over

the detergent container while doing so.

♦ Release the trigger9 as soon as clear cleaning

ﬂuid starts ﬂowing out.

♦ Lock the paint spray gun7 by turning the safety

catch6 with the tip as far back and up as

possible.

♦ Turn the pressure regulator dial3 to position 0

(oﬀ). Remove the plug from the mains socket.

♦ Depressurise the appliance.

♦ Remove the high-pressure hosew from the

paint spray gun7 with the aid of an adjustable

spanner.

♦ Disassemble the nozzle holdera along with

the nozzle5, holdero and plastic ringi

(see ﬁg. F). Clean all parts thoroughly using

suitable cleaning agents.

♦ Lock the paint spray gun7 by turning the safe-

ty catch6 with the tip as far back and up as

possible.

NOTE

► Clean the HEA ﬁltersq regularly. Replace

them if cleaning is no longer suﬃcient.

♦ Disconnect the suction hose2 and the return

hose1 from the appliance using the hose

clips l. Clean the outsides of the hoses.

♦ Remove the ﬁlter plateu of the intake ﬁltert

(see ﬁg. E).

♦ Clean the ﬁlter plateu thoroughly under

running water.

♦ Remove the high-pressure hosew from the

connecting threadr using an adjustable

spanner. Counter the connection thread r

using a second adjustable spanner.

♦ Dip the inlet valve h into a container ﬁlled with

conservation agent (e.g. ﬁne mechanical oil)

so that the ﬂuid can be sucked up.

♦ Insert the plug into a mains power socket.

♦ Hold a cloth in front of the connecting

threadr. Turn the pressure regulator dial3

to position 1 for about 5seconds. This helps

to preserve the appliance. Turn the pressure

regulator dial3 to position 0 (oﬀ).

♦ Remove the plug from the mains socket.

PAFS 550 A1

■ 14 │ GB│IE

Cleaning the inlet valve

WARNING! RISK OF INJURY!

Before carrying out any work on the

appliance, switch it oﬀ, disconnect

the mains plug and depressurise the

appliance!

NOTE

► If there are irremediable problems with the

paint suction, you should clean the inlet

valve h or replace it, if necessary.

♦ Disconnect the suction hose 2 from the appli-

ance.

♦ Remove the inlet valve h using an adjustable

spanner.

♦ Remove the O-ring g, ball f, washer d and

spring s (see ﬁg. G).

♦ Clean the parts thoroughly using suitable

cleaning agents. Replace them, if necessary.

NOTE

► You can obtain replacement parts not listed

here from the service hotline given in the

section "Service".

♦ Grease the O-ring g.

♦ Replace the parts into the inlet valve h

(see ﬁg. G).

♦ Screw the inlet valve h back into the appli-

ance. Tighten it using an adjustable spanner.

Cleaning the connecting thread

WARNING! RISK OF INJURY!

Before carrying out any work on the

appliance, switch it oﬀ, disconnect

the mains plug and depressurise the

appliance!

If you are still experiencing a poor spray pattern

after cleaning the nozzle, you should clean the

connecting thread r.

♦ Remove the high-pressure hosew from the

connecting threadr using an adjustable

spanner. Counter the nut of the connection

thread r with a second adjustable spanner.

♦ Loosen the fastening screw j with a Phillips

screwdriver (not supplied).

♦ Loosen the hex screw k with a 2 mm hex key

(not supplied).

♦ Remove the connection thread r using an

adjustable spanner.

♦ Clean the connecting thread r using a suitable

cleaning agent. Replace it, if necessary.

♦ Screw the connecting thread r back into the

appliance and tighten it using an adjustable

spanner.

♦ Retighten the fastening screw j with a Phillips

screwdriver.

♦ Turn the hex screw k with a 2 mm hex key.

Storage and transportation

■ Store the appliance in a dry, dust-free location.

■ Transport the appliance only when you have

taken it completely out of service. Transport

the appliance in such a way that it cannot be

damaged or soiled. Preferably, use the original

packaging.

PAFS 550 A1 GB│IE │ 15 ■

Troubleshooting

Fault Possible cause Remedy

The paint

spray gun

does not

spray.

The inserted

nozzle is

clogged.

Clean the nozzle

and use a suitable

HEA ﬁlter.

The HEA ﬁlter is

clogged.

Clean or replace

the HEA ﬁlter.

The paint spray

gun is locked.

Unlock the paint

spray gun.

The motor

is not

running.

The appliance is

not plugged in.

Insert the mains

plug into an ap-

propriate mains

socket.

The appliance

has overheated.

Follow the instruc-

tions in the section

"Overheating

protection".

There is no volt-

age on the

mains socket.

Check the mains

socket.

The appliance

has been operat-

ed and main-

tained according

to the operating

instructions, but

still does not

work.

Contact our

Customer Service

department.

Disposal

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling

plant.

Do not dispose of power tools

in the normal domestic waste!

According to the European Directive

2012/19/EU, used power tools must

be collected separately and recycled in an environ-

mentally sound manner.

Dispose of the packaging in an envi-

ronmentally friendly manner. Note the

labelling on the packaging and sepa-

rate the packaging material compo-

nents for disposal, if necessary. The packaging

materials are labelled with abbreviations (a) and

numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out product.

The product is recyclable, subject to

extended producer responsibility and

is collected separately.

Environmental compatibility and material

disposal

■ Paints and lacquers … are considered hazard-

ous waste and must be disposed of accordingly.

■ Observe the local regulations.

■ Observe the manufacturer's instructions.

■ Environmentally harmful chemicals must not be

allowed to get into the ground, groundwater

or any body of water.

■ Spraying work next to bodies of water or ad-

joining surfaces thereof (catchment area) is

therefore not permitted.

■ When purchasing paints or lacquers … pay

attention to their environmental compatibility.

PAFS 550 A1

■ 16 │ GB│IE

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from

the date of purchase. If this product has any faults,

you, the buyer, have certain statutory rights. Your

statutory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase (re-

ceipt) within the three-year warranty period, along

with a brief written description of the fault and of

when it occurred.

If the defect is covered by the warranty, your prod-

uct will either be repaired or replaced by us. The

repair or replacement of a product does not signify

the beginning of a new warranty period.

X 12 V and X 20 V Team Series battery packs

come with a 3-year warranty valid from the date of

purchase.

Warranty period and statutory claims

for defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must

be reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has

been damaged, improperly used or improperly

maintained. The directions in the operating instruc-

tions for the product regarding proper use of the

product are to be strictly followed. Uses and

actions that are discouraged in the operating

instructions or which are warned against must be

avoided.

This product is intended solely for private use and

not for commercial purposes. The warranty shall

be deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

over time

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Stránka sa načítava ...

Parkside AFS 550 A1 Návod na používanie

Parkside AFS 550 A1 Návod na používanie

V iných jazykoch

Súvisiace články

Ďalšie dokumenty