Philips QG3371/16 Používateľská príručka

User manual

QG3371

1

QG3371

ENGLISH 6

 19

 33

 46

 58

 70

 83

 97

 110

 122

 136

 150

 164

 177

 190

 202

4

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips

offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Mini foil shaver

2 Nose/ear hair trimmer

3 Hair clipper

4 Full metal precision trimmer

5 Full metal beard trimmer

6 Handle

7 On/off button

8 TURBO button

9 Battery status indicator/Turbo LED

10 Storage pouch

11 Small plug

12 Adapter

13 Cleaning brush

14 Beard and moustache comb (1-18mm)

15 Hair clipping comb (3-20mm)

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Keep the adapter dry.

Warning

- Check if the voltage indicated on the adapter

corresponds to the local mains voltage before you

connect the appliance.

ENGLISH

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug,

as this causes a hazardous situation.

- This appliance is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

- Keep the appliance and its cord out of the reach

of children.

Caution

- Use, charge and store the appliance at a

temperature between 5°C and 35°C.

- Only use the adapter supplied to charge the

appliance.

- If the appliance is subjected to a major change in

temperature, pressure or humidity, let the appliance

acclimatise for 30 minutes before you use it.

- If the adapter is damaged, always have it replaced

with one of the original type in order to avoid a

hazard.

- Always check the appliance before you use it.

Do not use the appliance if any of its parts is

damaged or broken, as this may cause injury.

Compliance with standards

- This appliance complies with the internationally

approved IEC Safety regulations and can be safely

cleaned under the tap.

- This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

ENGLISH 5

Charging

Charging takes approximately 1 hour. When the

appliance is fully charged, it has an operating time of

up to 50 minutes. When the battery status indicator

lights up orange, the battery is running low

(approx. 10 minutes of operating time left) indicating

you need to recharge the appliance soon.

Note: You can also quick charge the appliance, a 5 minute

charge equals approx. 5 minutes of operating time.

1 Switch off the appliance before you charge it.

2 Insert the small plug into the appliance.

3 Put the adapter in the wall socket.



The appliance is equipped with a turbo power

boost for fast results and a memory function that

remembers the last used speed setting.

Hair clipping

Preparing for hair clipping

1 Make sure that the head of the person whose

hair you intend to cut is at the same level as

your chest. This ensures that all parts of the

head are clearly visible and within easy reach.

2 Comb the hair in the growth direction.

ENGLISH6

Hair clipping with hair clipping comb

1 Place the hair clipper on the handle (1)

and turn it clockwise to x it (2).

2 Slide the hair clipping comb into the guiding

grooves on both sides of the handle.

3 Press the setting selector (1) and slide the

comb to the desired hair length setting (2).

You can choose any setting between 3 and 20mm

in steps of 1mm.

Tip: Write down the hair length settings you selected

to create a certain hairstyle as a reminder for future

clipping sessions.

4 Switch on the appliance.

5 Move the appliance slowly and against the

direction of hair growth. Press lightly.

Note: Since hair grows in different directions,

you need to move the appliance in different directions

as well (upward, downward or across).

ENGLISH 7

6 Always make sure that the at part of the

comb is in full contact with the scalp to obtain

an even result.

Make overlapping passes over the head to ensure

that you cut all the hair that needs to be cut.

Note: When you trim for the rst time, start at the highest

setting (20mm) to familiarise yourself with the appliance.

Hair clipping without hair clipping comb

You can use the trimmer without comb to clip hair

very close to the skin (to a length of 1mm) or to

create contours.

Caution: Be careful when you clip without the

comb because the trimmer removes every hair it

comes in contact with.

1 Press the setting selector (1) and slide the

comb upwards (2). Then pull the comb off the

appliance (3).

2 Before you start to contour the hairline

around the ears, comb the hair ends over the

ears.

3 Tilt the appliance in such a way that only one

edge of the trimmer touches the hair.

Only cut the hair ends. The hairline should be close

to the ear.

4 To contour the neckline and sideburns, turn

the appliance and make downward strokes.

5 Move the appliance slowly and smoothly.

Follow the natural hairline.

ENGLISH8

Beard trimming

When you trim your beard for the rst time,

be careful. Do not move the trimmer too fast.

Make smooth and gentle movements.

Beard trimming with the beard and

moustache comb

1 Place the beard trimmer on the handle (1)

and turn it clockwise to x it (2).

2 Slide the beard and moustache comb or

stubble comb into the guiding grooves on both

sides of the handle.

3 Press the setting selector (1) and slide the

comb to the desired hair length setting (2).

You can choose any setting between 1 and 18mm in

steps of 1mm.

4 Switch on the appliance.

5 Slowly move the trimmer against the hair

growth direction. Press lightly and always make

sure the surface of the comb is in full contact

with the skin.

Note: When you trim for the rst time, start at the

highest setting (18mm) to familiarise yourself with the

appliance.

Styling/contouring your beard

You can use the precision trimmer to cut shapes in

beard hair or scalp hair. It cuts hair very close to the

skin (to a length of 1mm).

ENGLISH 9

Caution: Be careful when you use the precision

trimmer because it removes every hair it comes in

contact with.

1 Place the precision trimmer on the handle (1)

and turn it clockwise to x it (2).

2 To achieve a good cutting result, move the

precision trimmer against the direction of

hair growth. Always make sure the precision

trimmer is in full contact with the skin.

3 Make careful and controlled movements with

the precision trimmer.

Tip: For the perfect nish, you can use the mini foil

shaver to make the edges and lines of your beard style

even smoother.

Grooming facial hair (nose and ear hair)



1 Place the nose/ear hair trimmer on the handle

(1) and turn it clockwise to x it (2).

2 Make sure your nostrils are clean.

3 Switch on the appliance and insert the tip of

the trimmer into one of your nostrils.

Do not insert the tip more than 0.5cm into your

nostril.

ENGLISH10

4 Slowly move the tip in and out while turning it

round at the same time to remove unwanted hair.

To reduce the tickling effect, make sure that you

press the side of the tip rmly against the skin.



1 Place the nose/ear hair trimmer on the handle

(1) and turn it clockwise to x it (2).

2 Clean the outer ear channel. Make sure it is

free from wax.

3 Switch on the appliance and move the tip softly

round the ear to remove hairs that stick out

beyond the rim of the ear.

4 Carefully insert the tip into the outer ear

channel.

Do not insert the tip more than 0.5cm into the ear

channel as this could damage the eardrum.

Cleaning

Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol

or acetone to clean the appliance.

Note: The appliance does not need any lubrication.

Clean the appliance after each use.

1 Make sure the appliance is switched off and

disconnected from the mains.

2 Remove any comb and/or attachment from the

appliance.

ENGLISH 11

3 Blow and/or shake out any hair that has

accumulated in the attachments and/or combs.

4 Clean the attachments, the combs and the

appliance under a lukewarm tap or with the

cleaning brush.

5 Clean the adapter with the cleaning brush or a

dry cloth.

Keep the adapter dry.

Cleaning the mini foil shaver

1 After each use, pull the top part of the mini foil

shaver off the bottom part.

The shaving foil is very delicate. Handle it carefully.

If the shaving foil is damaged, do not use the mini

foil shaver anymore.

Do not clean the shaving foil with the

cleaning brush, as this may cause damage.

2 Blow and/or shake out any hair that has

accumulated inside the mini foil shaver.

3 Clean the top part of the mini foil shaver under

a lukewarm tap.

ENGLISH12

Storage

Store the appliance and attachments in the storage

pouch to prevent damage, or store it on the

storage stand.

Ordering accessories

To buy accessories or spare parts, visit

www.shop.philips.com/service or go to your

Philips dealer. You can also contact the

Philips Consumer Care Centre in your country

(see the worldwide guarantee leaet for contact details).

Environment

- Do not throw away the appliance with the normal

household waste at the end of its life, but hand it in

at an ofcial collection point for recycling. By doing

this, you help to preserve the environment.

- The built-in rechargeable battery contains

substances that may pollute the environment.

Always remove the battery before you discard

and hand in the appliance at an ofcial collection

point. Dispose of the battery at an ofcial

collection point for batteries. If you have trouble

removing the battery, you can also take the

appliance to a Philips service centre. The staff of

this centre will remove the battery for you and

will dispose of it in an environmentally safe way.

ENGLISH 13

Removing the rechargeable battery

Only remove the rechargeable battery when you

discard the appliance. Make sure the battery is

completely empty when you remove it.

Be careful, the battery strips and housing parts are

very sharp.

1 Check if there are any screws in the back or

front of the appliance. If so, remove them.

2 Remove the back and/or front panel of the

appliance with a screwdriver. If necessary,

also remove additional screws and/or parts

until you see the printed circuit board with the

rechargeable battery.

3 If necessary, cut the wires to separate the

printed circuit board and the rechargeable

battery from the appliance.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate

worldwide guarantee leaet.

ENGLISH14



Problem Possible

cause

Solution

The combs

do not stay

attached to

the handle.

You do

not attach

the comb

correctly.

Slide the comb into the guiding grooves

on both sides of the handle until you

hear a click.

The guiding

grooves are

dirty.

Clean the appliance and the guiding

grooves thoroughly.

The comb is

broken.

Go to your Philips dealer or contact a

Philips service centre to purchase a new

comb.

The

appliance

does not

work

anymore.

The

rechargeable

battery is

empty.

Charge the appliance (see chapter

‘Charging’). Make sure you switch off

the appliance before you charge it.

During charging, the charging light on

the adapter ashes. If the charging light

does not ash, check whether there is

a power failure or if the wall socket is

live. If there is no power failure and the

wall socket is live but the charging light

still does not ash, take the appliance to

your dealer or a Philips service centre.

The

appliance

does not

charge

when it is

connected

to the mains.

The

appliance

has to be

switched off

when you

charge it.

Switch off the appliance.

ENGLISH 15

Problem Possible

cause

Solution

The

appliance

does not

trim as well

as it used to.

The cutting

element

of the

attachment

you are using

is dirty.

Remove the attachment from the

appliance. Clean the attachment under a

lukewarm tap.

The

appliance

becomes

hot.

The cutting

element

of the

attachment

you are using

is dirty.

Remove the attachment from the

appliance. Clean the attachment under a

lukewarm tap.

ENGLISH16

17



Поздравления за вашата покупка и добре дошли във

Philips! За да се възползвате изцяло от предлаганата

от Philips поддръжка, регистрирайте продукта си на

адрес www.philips.com/welcome.



1 Самобръсначка с минипластина

2 Машинка за подстригване на нос и уши

3 Машинка за подстригване

4 Широка метална машинка за прецизно

подстригване

5 Широка метална машинка за подстригване на

брада

6 Дръжка

7 Бутон за вкл./изкл.

8 Бутон TURBO

9 Светодиоден индикатор за батерията/Turbo

10 Торбичка за съхранение

11 Малък жак

12 Адаптер

13 Четка за почистване

14 Гребен за брада и мустаци (1-18 мм)

15 Гребен за подстригване на коса (3-20 мм)



Преди да използвате уреда, прочетете

внимателно това ръководство за потребителя и

го запазете за справка в бъдеще.



- Пазете адаптера сух.





- Преди да свържете уреда, проверете дали

напрежението, посочено върху адаптера,

отговаря на това на местната електрическа мрежа.

- В адаптера има трансформатор. Не отрязвайте

адаптера, за да го замените с друг щепсел,

тъй като това крие опасности.

- Този уред не е предназначен за ползване от

хора (включително деца) с намалени физически

възприятия или умствени недъзи или без опит

и познания, ако са оставени без наблюдение и

не са инструктирани от страна на отговарящо

за тяхната безопасност лице относно начина

на използване на уреда.

- Пазете уреда и кабела далече от достъп на

деца.



- Използвайте, зареждайте и съхранявайте

уредите при температура между 5°C и 35°C.

- За зареждане на уреда използвайте само

доставения с него адаптер.

- Ако уредът е бил подложен на значителни

промени в температурата, налягането или

влажността, изчакайте да се климатизира за 30

минути, преди да го използвате.

- С оглед на предотвратяване на злополука,

винаги заменяйте повредения адаптер само с

оригинален такъв.

- Винаги проверявайте уреда, преди да го

използвате. Не използвайте уреда, ако някоя от

частите му е повредена или счупена, тъй като

това може да причини нараняване.

18



- Този уред съответства на международно

одобрената нормативна уредба за безопасност

IEC и може да се почиства безопасно под

чешмата.

- Този уред Philips е в съответствие с

всички стандарти по отношение на

електромагнитните излъчвания (EMF).

Ако се употребява правилно и съобразно

инструкциите в това ръководство за

потребителя, уредът е безопасен за използване

според наличните досега научни факти.



Зареждането отнема около 1 час. Когато уредът

е напълно зареден, той може да осигури до 50

минути работа. Когато индикаторът за батерията

свети в оранжево, батерията е почти изтощена

(остават около 10 минути работа) и скоро ще

трябва да заредите уреда.

Забележка: Има възможност за бързо зареждане

на уреда, при което 5-минутно зареждане се

равнява на около 5 минути работа.

1 Изключвайте уреда преди зареждане.

2 Включете малкия жак в уреда.

3 Включете адаптера в контакта.



Уредът е снабден с турбо скорост за

допълнителна мощност и по-бърз резултат,

както и с функция “памет” за запаметяване на

последно използваната настройка за скорост.

 19





1 Застанете така, че главата на човека,

когото подстригвате, да е на нивото на

гърдите ви - така всички части на главата му

ще се виждат добре и ще са лесно достъпни.

2 Срешете косата по посоката на растежа.





1 Сложете машинката за подстригване на

коса върху дръжката (1) и я завъртете по

часовниковата стрелка, за да я фиксирате (2).

2 Плъзнете гребена за подстригване на коса в

направляващите жлебове от двете страни на

дръжката.

3 Натиснете селектора за настройка (1)

и плъзнете гребена на желаната настройка

за дължина (2).

Можете да изберете всяка настройка между 3

и 20 мм на стъпки от 1 мм.

Съвет: Запишете си избраните настройки за

дължина на косата при оформяне на дадена

прическа, за да ги използвате за справка при

следващи подстригвания.

20

Stránka sa načítava...

Philips QG3371/16 Používateľská príručka

Philips QG3371/16 Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty