Silvercrest KH 2030 Operating Instructions Manual

KH 2030

KOMPERNASS GMBH · BURGSTRASSE 21 ·

D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH2030-01/09-V2

MULTI-BAND RADIO

B

MULTI-BAND RADIO

Operating instructions

RÁDIOPRIJÍMAČ

Návod na obsluhu

RÁDIO

Návod k obsluze

CV_KH2030_DT25841_LB4B.qxd 12.01.2009 14:00 Uhr Seite 1

KH 2030

f

d

g

;

2)

l

j

h

k

s

a

o

i

r

y

u

A

B

q

ew

t

CV_KH2030_DT25841_LB4B.qxd 12.01.2009 14:00 Uhr Seite 4

- 1 -

CONTENTS PAGE

Intended use 2

Technical Data 2

Safety information 4

Operating elements 7

Starting up 8

General functions 10

Time functions 11

Time, date, time zone and world time 11

Select display mode 15

Alarm function 15

Stop watch function 18

Countdown function 18

Radio operation 19

Setting the station 20

Fine tuning 21

Aerial 21

Memory functions 22

Cleaning 24

Disposal 24

Importer 25

Warranty & service 26

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 1

MULTI-BAND RADIO KH2030

Before using the device for the first time, read these operating instructions

carefully and keep them for later reference. Hand the instructions over

when transferring the device to a third party.

Intended use

This device is designed to receive generally approved radio transmissions in

all countries (world receiver) and only for domestic use.

It has not been designed to receive transmissions that are not generally ap-

proved, nor as part of safety radio systems, e.g. on board sports boats, nor

for industrial or commercial use. It has also not been designed for use in

temperatures beyond those stated in the Technical Data.

Technical Data

This device has been tested and approved for adherence to the basic requi-

rements and the other relevant regulations of the EMC Directive

2004/108/EC and the Directive on Low Voltage Devices 2006/95/EC.

Power consumption: 5 watts

Power consumption Standby: 1.3 W

Operating temperature: +5

~

+35°C

Humidity: 5

~

90%

(no condensation)

- 2 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 2

Dimensions (L x W x H): 180 x 40 x 110 mm

Weight: ca. 380 g

Batteries

4x 1.5 V, Type AA/LR6/Mignon (not supplied)

Frequency range radio:

VHF (FM): 87 – 109 MHz

SW: 5.85 - 17.90 MHz

MW (AM) Europe 522 - 1656 kHz

MW (AM) USA 520 - 1710 kHz

LW 144 - 299 kHz

The technical features of the device enable the frequency ranges stated

above to be set. Various countries may have different national rules on the

radio frequency ranges assigned. Please note that you may not sell, trans-

fer to third parties or abuse information received outside the assigned ra-

dio frequency ranges.

Tuning ranges (NORMAL/FINE):

FM (VHF) 100 kHz/50 kHz

SW 5 kHz/1 kHz

MW (AM) Europe 9 kHz/1 kHz

MW (AM) USA 10 kHz/1 kHz

LW 1 kHz

Sensitivity: SW can be set to 2 intervals

General

Memory positions : 1600 (400 for each frequency range)

- 3 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 3

Headphones

Model: E105

Impedance: 32 Ω

Wideband characteristic Voltage (WBCV): 100 mV

Headphone socket

max. Output voltage: 20 mV

Power transformer

Manufacturer: S&S MFG. LTD.

Model: A400-75

Primary: 230 V

~

50 Hz / 30 mA

Secondary: 7.5 V DC 400 mA / 3VA

Safety information

• This device has not been designed for use by people (including chil-

dren) with restricted physical, sensory or intellectual abilities or lack of

experience and/or knowledge, unless they are supervised by a re-

sponsible person (for their own safety) or have received instructions

on how to use the device.

• Children should be supervised to ensure that they do not play with the

device.

• In order to avoid the device being switched on unintentionally, remo-

ve the adapter from the mains socket after each use and before

cleaning.

• Check the device and all parts for visible damage. The device’s safety con-

cept can only work if the device is in perfect condition.

• A mains adapter connected to the device must always be easily ac-

cessible so that the device can be quickly disconnected from the

mains power in an emergency.

- 4 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 4

Risk of electric shock!

• Only connect the device to a properly installed and earthed mains so-

cket. The mains voltage must agree with that stated on the device’s

specification plate.

• Damaged adapters or mains cables should be exchanged immediate-

ly by an authorised technician or the Customer Service in order to

avoid risks.

• Connection cables or devices that do not work perfectly or have been

damaged should be repaired or exchanged immediately by Customer

Services.

Never immerse the device in water! Simply wipe it with a slightly

damp cloth.

• Do not expose the device to rain or use it in a damp or wet environ-

ment.

• Ensure that the connection cable is never wet or damp when in use.

• You must not open or repair the device’s housing. This can be dangerous

and renders the warranty null and void.

• Protect the device from moisture and sprayed water. Therefore do not

place any objects filled with water (e.g. vases) on or near the device.

Risk of fire!

• Do not use the device near hot surfaces.

• Do not set the device up where it is exposed to direct sunlight. This

could cause it to overheat and damage it beyond repair.

• Never leave the device unattended during operation.

• Never cover the device’s ventilation slots when it is switched on.

• Do not place open flames, such as candles, on or near the device.

- 5 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 5

Risk of injury

• Keep children away from the connection cable and device. Children

frequently underestimate the danger of electrical devices.

• If the device has fallen down or is damaged it must no longer be used.

Have the device checked by a qualified specialist and, if necessary, re-

paired.

• Batteries must not be handled by children.

Children can put batteries in their mouths and swallow them.

If a battery has been swallowed, obtain medical assistance immediately.

Thunder storms!

Devices connected to mains power can be damaged during a thun-

der storm. If there is a thunder storm, always remove the mains plug

from the socket.

Information on voltage surges (EFT/electrical fast

transient) and electrostatic discharges:

If the product does not work properly due to electrical fast transient

processes (voltage surges) or electrostatic discharge, it must be

reset to restore normal operation. If necessary, remove the plug from

the power socket and insert it again. The batteries (if used) must be re-

moved and reinserted.

Information on separating the device from mains

power

The POWER button on this device does not completely separate it

from the mains network. In addition, the device uses power when in

standby mode. In order to completely separate the device from the

mains supply the plug must be removed from the mains socket.

- 6 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 6

Notes on handling batteries

The device uses batteries. Please note the following on handling batteries:

Risk of explosion!

Do not throw batteries into a fire. Do not recharge batteries.

• Never open, solder or weld batteries. There is a risk of explosion and injury!

• Check batteries regularly. Leaking batteries can damage the device.

• If the appliance is not going to be used for long periods, remove the

batteries.

• If batteries leak, put on protective gloves.

• Clean the battery compartment and contacts with a dry cloth.

Caution!

No liability/warranty applies to damage to the device caused by moi-

sture due to water penetrating the device or overheating!

Operating elements

 Front side

q

Memory buttons M.0/5–M.4/9

w

Screen

e

button SNOOZE

r

Frequency selection switch

t

button PAGE

y

button FINE

u

button POWER

i

buttons UP/DOWN

- 7 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 7

o

buttons VOL.+ (AL-1)/VOL.– (AL-2)

a

button MODE

s

button BASS

d

button MEMORY SCAN

f

button MEM

g

speakers

 Back

h

Stand

j

Aerial

k

Carrying strap

l

switch SW SEN.

;

Headphone output

2)

EXT. DC 7.5 V 400 mA: Mains adapter connection

Starting up

Unpack the device

Remove all packaging materials.

Caution!

Do not let children play with the plastic film. There is a risk of suffocation.

Check the items supplied

Whilst unpacking, check that all of the following items are available to

you:

• Shortwave Radio

• Power transformer

- 8 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 8

• Headphones

• Storage case

• These operating instructions, complete with the warranty card

Mains and battery operation

When you disconnect the radio from the mains supply, any settings you

may have made (time, alarm, stations in memory) will be lost. If you wish

to keep these settings, insert batteries (see below) before disconnecting.

Inserting batteries

The device can also be operated with batteries (not supplied) as well as

from the mains. You will need four 1.5V mignon batteries, size AA, LR6.

• Open the battery compartment on the rear of the device by sliding

the cover downwards.

• Insert four batteries into the compartment, paying attention to the po-

larity.

• Replace the cover on the battery compartment.

If the batteries are too weak, this is indicated on the screen by a flashing

symbol .

Mains connection

• Connect the plug of the mains adapter to the EXT. DC 7.5 V 400 mA socket

on the side of the device.

• Plug the mains adapter into an easily accessible socket. To avoid trip-

ping hazards, please avoid using an extension cable.

Connecting headphones

On the left side of the radio, you will find the headphone socket.

- 9 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 9

Caution!

Use only the supplied headphones of Type E105.

• Insert the headphone jack plug into the headphone output.

The speaker will be deactivated automatically.

Caution:

Listening to music with headphones over long periods of time

and at a high volume may damage your hearing!

General functions

Key lock

In order to prevent changing the settings unintentionally by touching the

buttons, you can activate the key lock.

• Press and hold down the

MEM button for around 3 seconds. On screen,

the message flashes. All buttons, except the buttons

SNOOZE and

MEM, are now blocked.

• Press and hold down the

MEM button again for about 3 seconds to can-

cel the key lock. The message on the screen disappears.

Screen lighting

• Press any button to illuminate the screen. The screen will remain lit for

about 10 seconds.

Stand

• Fold out the base on the rear of the device to make the device more

stable.

- 10 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 10

Time functions

The time functions can only be set when the radio is switched off. When used

for the first time the preset time of the global receiver is set to “0:00 00”.

If the device is disconnected from its power supply the settings are lost.

Time, date, time zone and world time

You can set the time, date and time zone via the MODE button. You can also

query and set the world time, data alarm, medium wave reception, alarm time

reception and hourly mode.

When you press

MODE, the function to be set flashes for about 15 seconds.

During this time, adjust the setting with the

UP/DOWN buttons.

• Press

MODE x 1: Setting clock time

• Press

MODE x 2: Setting the date

• Press

MODE x 3: Set time zone (“Local City”)

• Press

MODE x 4: Show world time

• Press

MODE x 5: Date alarm

• Press

MODE x 6: Set reception range for medium wave.

• Press

MODE x 7: Set alarm pause.

• Press

MODE x 8: Set 12/24 hour mode.

To apply a setting, just wait until the screen stops flashing (the screen reverts to the

time indication) or press

MODE to move on to the next function.

Setting clock time

• Press MODE once. The most recently set time flashes on the screen.

• Press the

UP or DOWN button to move the time forward or backward at

minute intervals. Hold down one of the buttons for a few seconds to

move the setting forward or backward quickly at 10 minute intervals.

- 11 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 11

Note:

Set the time without summer time offset. If summer time is required, this can be

set when setting the time zone.

Setting the date

• Press MODE again or twice.

The date set flashes on the screen (“Tu 01:01 08” when first switched on).

• Press the

UP or DOWN button to move the date forward or backward.

Keep either of these buttons pressed for a few seconds to change the

date in ten-day steps.

The weekday indication follows automatically. The indication uses the first

two letters of the English name of the day.

The built-in calendar runs from 2000 to 2099.

Day of the week indication:

Su = Sunday

Mo = Monday

Tu = Tuesday

We = Wednesday

Th = Thursday

Fr = Friday

Sa = Saturday

Setting the time zone

• Press MODE again or three times. The selected time zone flashes on the

screen as the abbreviation for the corresponding city (UTC when first

switched on); the time disappears.

• Press the

UP or DOWN button to move the time zone forward or backward.

The following table summarises the city abbreviations for the time zones and

time differences.

- 12 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 12

- 13 -

Short code Difference

from CET

Town

HNL -10:00 Honolulu/USA

ANC -9:00 Anchorage/USA

YVR -8:00 Vancouver/Canada

LAX -8:00 Los Angeles/USA

DEN -7:00 Denver/USA

CHI -6:00 Chicago/USA

MEX -6:00 Mexico City/Mexico

NYC -5:00 New York/USA

YYZ -5:00 Toronto/Canada

YUL -5:00 Montreal/Canada

CCS -4:00 Caracas/Venezuela

RIO -3:00 Rio de Janeiro/Brazil

BUE -3:00 Buenos Aires/Argentina

UTC* 0:00 Universal Time Coordinated

LON 0:00 London/GB

MUN 1:00 Munich/Germany

FRA 1:00 Frankfurt/Germany

PAR 1:00 Paris/France

ROM 1:00 Rome/Italy

CAI 2:00 Cairo/Egypt

IST 2:00 Istanbul/Turkey

MOW 3:00 Moscow/Russia

KWI 3:00 Kuwait City/Kuwait

DXB 4:00 Dubai/United Arab Emirates

KHI 5:00 Karachi/Pakistan

DAC 6:00 Dhaka/Bangladesh

BKK 7:00 Bangkok/Thailand

SIN 8:00 Singapore

HKG 8:00 Hong Kong

PEK 8:00 Beijing/China

TYO 9:00 Tokyo/Japan

SYD 10:00 Sydney/Australia

NOU 11:00 Noumea/New Caledonia

AKL 12:00 Auckland/New Zealand

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 13

*UTC

Universal Time Coordinated UTC). UTC is the reference for the times

of the various time zones around the world.

Summer time offset

• While the time zone indication is still flashing, press the SNOOZE button.

The screen shows the SUN OFF message when summer time has been

deactivated.

• Press the

SNOOZE button again. The screen now shows SUN ON. Sum-

mer time offset is now activated and the clock moves one hour ahead.

Show world time

• Press MODE again or four times to show the world time. The city abbre-

viation appears with the corresponding time.

• Press the

UP or DOWN button to move the time zone forward or backward.

Special date alarm

• Press the MODE button a fifth time to set the special date alarm. The

screen flashes SDA1 and the date in succession.

• Press the

PAGE button to select one of the ten settable date alarms

(SDA1–SDA 10).

• Press the

UP or DOWN button to set the date on which the alarm should

sound.

• Press the

SNOOZE button to ignore the year number setting so that the

alarm sounds every year.

• If the current date is the same as the SDA date, an alarm sounds

every hour from 8 o’clock on this day. In addition, the SDA message

will flash on the screen.

• Turn off the alarm by pressing any button.

- 14 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 14

Note:

In order to completely deactivate the date alarm set a date that is in the

past!

Setting 12/24 hour mode

• Press MODE eight times. The screen shows the”24 HR” message for 24-

hour mode.

• Press the

UP button to set the 24 hour mode.

• Press the

DOWN button to set the 12 hour mode.

“12HR” is displayed on the screen. In the afternoon in addition PM is

shown on the screen.

Select display mode

You can select which information is shown on the screen when the radio is

switched off.

The selected mode is indicated by a corresponding symbol on the screen.

When the radio is switched off, select the display mode by repeatedly

pressing the

FINE button in accordance with the following table:

Symbol on the screen display mode

CLK only the time is displayed

CITY The time and world time are shown in succession

DATE The time and date are shown in succession

CIT DAT the time, date and world time are shown in succession

Alarm function

The world receiver provides two alarms that can be set independently of

one another, AL1 and AL2. For both, you can set:

...whether the alarm should operate on every day of the week or only

from Monday to Friday;

... whether you wish to be woken by the alarm tone or the radio.

- 15 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 15

Setting the alarm time

You can set two alarm times in your world receiver.

• Press the

VOL.+/AL–1 (or VOL.–/AL–2) button. The screen shows the most

recently set alarm time and the symbol for the alarm type.

• Press the

UP or DOWN button to move the alarm time forward or back-

ward at minute intervals. Hold down one of the buttons for a few se-

conds to move the setting forward or backward quickly at 10 minute

intervals.

• Press the

VOL.+/AL–1 (or VOL.–/AL–2) button until the desired alarm functi-

on (see table above) is indicated on the screen.

• Press the

SNOOZE button to set the weekday on which you want the

alarm to sound: You can choose between week days (Mo, Tu, We,

Th, Fr), weekend (Su, Sa), every day (Su, Mo, Tu, We, Th, Fr, Sa) or

the current day of the week. The selected setting is shown on the

screen.

• Press the

SNOOZE button until the desired alarm days are set. Hold

down the

SNOOZE button until the screen shows an individual week day.

• Press the

SNOOZE button to set the desired week day.

To go back to selecting week days, weekend or every day, briefly hold

down the

SNOOZE button again.

• Press the

MODE button to save the setting and return to the time mode.

The setting is also saved if you wait around 15 seconds until the

screen returns to displaying the time.

- 16 -

Alarm function Symbol on the screen

Acoustic signals

Radio

Switched off No symbol

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 16

When the alarm sounds...

• and the “Radio” alarm function has been selected, the radio opera-

tes for one hour at a predefined alarm volume. To switch off press the

VOL.+/AL–1 (or VOL.–/AL–2) button.

• and the “signal sounds” alarm function has been selected, the signal sound

is played for 10 minutes. To switch off press the

VOL.+/AL–1 (or VOL.–/AL–2)

button.

Note:

Please note that a station must be selected for the radio alarm to work.

Interrupting the alarm

• Press the SNOOZE button to interrupt the alarm for 10 minutes.

Set snooze time

• With the radio switched off, press the button MODE seven times. The

screen displays the snooze time set (default is ”SNO 10”).

• Use the

UP and DOWN buttons to set the snooze time to a time between

1 and 59 minutes.

Turning off the alarm function

• Press the VOL.+/AL–1 or VOL.–/AL–2 button until the relevant alarm sym-

bols disappear from the screen.

- 17 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 17

Stop watch function

The stop watch function is only available when the radio is switched off.

• Press and hold down the

PAGE button for around 2 seconds, the screen

shows 00.00.0 U.

• Press

SNOOZE to start the stop watch. The maximum time for the stop

watch is 99 minutes and 59 seconds. If the stop watch exceeds the

maximum time, 99:59.0 is displayed and flashes.

• During time measurement, it can be stopped by pressing

SNOOZE.

• Pressing

SNOOZE again restarts the stop watch.

• Hold down

SNOOZE to reset the stop watch.

• Leave the stop watch by pressing

PAGE.

Countdown function

The countdown function is only available when the radio is switched off.

Set and save countdown

• Press and hold down the MEMORY SCAN button for around 2 seconds, the

screen shows D 00.00.

• Press the

UP or DOWN button to set the desired time.

5 countdown times are preset on the memory buttons and you can open

these directly using the corresponding memory button:

Button

M.0/5 10:00

Button

M.1/6 30:00

Button

M.2/7 45:00

Button

M.3/8 60:00

Button

M.4/9 90:00

• Press the

MEM button to save the set time, the memory space indicator MEM

flashes on the screen. Now use the M.0/5–M.4/9 buttons to select a memo-

ry space; when you press the relevant memory key the time is saved in this

memory space and the time previously stored there overwritten.

- 18 -

IB_KH2030_DT25841_LB4B 12.01.2009 17:11 Uhr Seite 18

Stránka sa načítava ...

Silvercrest KH 2030 Operating Instructions Manual

Silvercrest KH 2030 Operating Instructions Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty