HP DesignJet T1120 SD Multifunction Printer series referenčná príručka

HP Designjet T1120 SD-MFP

Quick reference guide

EN

Learning Products Barcelona - Hewlett-Packard Company

HP Designjet T1120 SD-MFP

Hızlı başvuru kılavuzu

TR

HP Designjet T1120 SD-MFP

Stručná referenční příručka

CS

HP Designjet T1120 SD-MFP

Felhasználói gyorskalauz

HU

You can nd legal and warranty information on the CD. Further information is available at HP’s support Web

site (http://www.hp.com/go/knowledge_center/).

Legal notices

The information contained herein is subject to change without notice. The only warranties for HP Products and

services are set forth in the express warranty statement accompanying such products and services. Nothing herein

should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or

omissions contained herein.

CD'de yasal ve garanti ile ilgili bilgiler mevcuttur. Diğer bilgiler HP’nin destek web sitesinde

(http://www.hp.com/go/knowledge_center/) bulunmaktadır.

Yasal bildirimler

Burada yer alan bilgiler önceden bildirilmeden değiştirilebilir. HP ürün ve hizmetleri için yalnızca söz konusu ürün

ve hizmetlere eşlik eden açık garanti belgelerinde belirtilen garantiler geçerlidir. Burada kullanılan hiçbir ifade ek

garanti olarak yorumlanamaz. HP, bu belgedeki teknik hatalardan veya yazım hatalarından ya da eksikliklerden

sorumlu tutulamaz.

Na disku CD naleznete právní ujednání a informace o záruce. Další informace jsou k dispozici

na webu podpory společnosti HP (http://www.hp.com/go/knowledge_center/).

Právní informace

Informace v tomto dokumentu mohou být změněny bez předchozího upozornění. Jediné záruky poskytované

k produktům a službám HP jsou výslovně uvedeny v prohlášení o záruce, které se dodává společně s těmito

produkty a službami. Žádné z informací uvedených v tomto dokumentu nemohou sloužit jako podklad pro

vyvození dalších záruk. Společnost HP nenese odpovědnost za případné technické či redakční chyby ani

opomenutí v tomto dokumentu.

A CD-lemezen jogi tudnivalókat és a jótállással kapcsolatos információkat találhat. További információ

a HP terméktámogatási webhelyén található (http://www.hp.com/go/knowledge_center/).

Jogi kitételek

Az itt található információk előzetes értesítés nélkül megváltozhatnak. A HP termékekre és szolgáltatásokra

vonatkozó garanciákat kizárólag az ilyen termékek és szolgáltatások kifejezett garancianyilatkozatában rögzítettek

szerint vállaljuk. Az itt talált információk semmilyen módon nem tekinthetők további garanciának. A HP nem felelős

az itt található semmilyen technikai vagy szerkesztési hibáért vagy kihagyásért.

EN

TR

HU

CS

Learning Products Barcelona - Hewlett-Packard Company

Table of contents

1 Introduction

Using this guide .............................................................................................. 1

Scanner software ............................................................................................ 2

Scanner .......................................................................................................... 3

Documentation and help ................................................................................. 3

2 Basic operations

Turn the scanner on or off .............................................................................. 4

Load and eject documents .............................................................................. 5

Set a destination folder for scans ................................................................... 6

Copy a document ............................................................................................ 8

Scan to a file ................................................................................................... 9

Batch scan and batch copy ........................................................................... 10

Specify the original type and make image adjustments ................................ 11

Set input and output sizes ............................................................................ 13

Preview copies and scans ............................................................................ 15

Set the output quality .................................................................................... 17

Create a media profile .................................................................................. 19

View, move, rename or delete scanned files ................................................ 21

System setup and options ............................................................................ 22

3 Maintenance

Clean the glass plate and the scanning area ................................................ 25

Calibrate the scanner .................................................................................... 27

Calibrate the touch screen pointer ................................................................ 29

Replace the scanner glass plate ................................................................... 29

4 Troubleshooting

The system reports an error ......................................................................... 30

There is a paper jam ..................................................................................... 30

Streaks in the scanned image ...................................................................... 32

Lines in the scanned image appear too thin or discontinuous ...................... 33

Cannot connect or scan to a destination folder on the LAN ......................... 33

Image cropped—not whole image scanned ................................................. 34

A media profile cannot be generated ............................................................ 34

My color matching results are not optimal .................................................... 35

I need to update or recover the system ........................................................ 35

ENWW

Learning Products Barcelona - Hewlett-Packard Company

EN

The system software is in the wrong language ............................................. 36

Install new system software .......................................................................... 37

Index ............................................................................................................................... 39

ENWW

Learning Products Barcelona - Hewlett-Packard Company

1Introduction

Using this guide

This guide is organized into the following chapters.

1. Introduction: This chapter provides a brief introduction to the software,

scanner device and available documentation.

2. Basic operations: This chapter helps you to carry out various common

procedures.

3. Maintenance: This chapter helps you to carry out various calibration and

maintenance procedures.

4. Troubleshooting: This chapter helps you to solve problems that may occur

while scanning.

5. Index: In addition to the table of contents, there is an alphabetical index to

help you to find topics quickly.

Warnings and cautions

Symbols are used in this manual to ensure the proper use of the printer and to

prevent printer damage. Follow the instructions that are marked with these symbols.

WARNING! Failure to follow the guidelines that are marked with this symbol could

result in serious personal injury or death.

CAUTION: Failure to follow the guidelines that are marked with this symbol could

result in minor personal injury or damage to the product.

ENWW

Using this guide

1

Introduction

Learning Products Barcelona - Hewlett-Packard Company

Scanner software

The scanner software runs automatically when you turn on the touch screen. The

main screen is divided into the following sections:

●

Main menu area

●

Right bar, top: the task buttons

●

Right bar, bottom: the function buttons

Task buttons

Press this button to set the program in the copy (scan to printer) task mode.

Press this button to set the program in the scan (scan to file) task mode.

Press this button to open program settings and preference menus.

Function buttons

File manager: Opens the File Manager dialog box.

Online help: Provides detailed information on many topics. Opens instructions related to

your current task.

Stop: Cancels the current activity.

Start scan/copy: Initiates the copy or scan, depending on which task button has been

selected.

2 Chapter 1 Introduction ENWW

Introduction

Learning Products Barcelona - Hewlett-Packard Company

Scanner

1. Scanner lid

2. Touch screen for scan/copy application

3. Release buttons for opening scanner lid

4. Scanner bed: paper feed area

5. Insertion slot for document feeding

6. USB port

7. Operator's panel

8. Paper forward button

9. Paper backward button

10. Power button and indicator

Documentation and help

This Quick Reference Guide provides a brief overview of the system and software.

The Online Help function button

opens the online help window and displays

general help on the current task (Scan, Copy, Options).

The online help window’s Home button

will take you to a table of contents with

links to online help sections and topics.

In many dialogs you will find a Context-sensitive Help button

that will open

instructions specifically related to the current dialog and its options.

ENWW

Scanner

3

Introduction

Learning Products Barcelona - Hewlett-Packard Company

2 Basic operations

Turn the scanner on or off

The system (scanner, screen and software) can be turned on or off by pressing the

power button on the scanner operation panel.

NOTE: The printer has a separate power on/off button. Normally this button is

always left turned on and is not pressed in connection with restarting the system.

Turn on

Press the power button. The power LED shows a green light.

Turn off

Press the power button. The power LED blinks and then turns off.

Restart

Press the power button to turn the system off and then press it again to turn the

system on.

4 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Load and eject documents

Load document

1. Load your document with the image side facing upwards. Align the center of

the document with the center arrow mark on and above the scanner bed.

2. Use the standard size markings to help align the document for a straight scan

path.

3. Push the original into the insertion slot until you feel it contact the rollers.

4. The scanner will automatically grab the original and move it into start-scan

position.

Eject document

●

Press the Paper Backward button to eject the original back to the scanner

feeding bed (towards you).

ENWW

Load and eject documents

5

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

●

Press the Paper Forward button if you wish to eject the original out the back

of the scanner.

Set a destination folder for scans

The instructions below describe how to set up and select a destination folder in

which you will save your scan-to-file output. Destinations are folders on computers

known to your system through the local network (LAN) or folders on a USB flash

drive inserted in the touch screen.

1. Make sure your system and any intended destination computers are correctly

set up on your local network (LAN). Configuration of your system on the LAN

is carried out through the Options > Advanced Options > Network menu.

This is a system administrator option that may require a password.

2. If you wish to save your scans on a USB flash drive, press the Scan button

and insert the drive into the USB port on the touch screen. The system will

detect the drive and enquire whether you want to set/change the destination

to USB.

3. To access the destination setup options, press Options > Advanced

Options > Manage Destinations. From there you can select, add and change

destinations.

6 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Select a destination

Select a destination from the list of destinations previously created and saved on

the system. If there are no destinations available, or you want to use a destination

that is not on the list, you will have to add a new destination. Press the USB

destination if you want to scan to an inserted USB flash drive.

Add a new destination

Press the Add button to enter destination details. Enter values in the Label, Network

Path, Domain, Username and Password fields. Select Remember if you want to

save the destination password in the system. Leave Remember unselected if you

want users to enter the password to connect to the destination. Press Test

Connection to check your settings.

Change (edit) a destination

Press the Change button and edit the Label, Network Path, Domain, Username

and Password fields. Select Remember if you want to save the destination

password in the system. Leave Remember unselected if you want users to enter

the password to connect to the destination. Press Test Connection to check your

settings.

Remove a destination

Select a destination from the Destinations list and press the Remove button.

ENWW

Set a destination folder for scans

7

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Copy a document

Follow the steps below to make a copy (scan to print).

1. Insert and feed your document into the scanner, with the side to be scanned

facing upwards.

2. Make sure the printer is turned on and the intended media is loaded.

NOTE: To copy, you need a media profile for the loaded media. The system

comes with a set of media profiles for the most commonly-used media. If you

need to create a new media profile, see

Create a media profile

on page 19.

3. Press the Copy button to access the copy (scan to print) settings and buttons.

The Copy dialog is shown below.

4. Press the Original Type button and select the type that matches your

document and required output. See

Specify the original type and make image

adjustments on page 11.

5. Press the Quality button and select the desired quality of your output.

6. Press the Scan Area button to set the size of the image capture area. If you

wish to capture the whole image, select Auto and the system will measure

and set the size for you.

7. Press the Resize button to determine the size of the printed copy. Set to No

if you want a 1:1 copy.

8. Press the Copies button to select how many copies you want printed with the

job.

9. Toggle the Preview before Copy button to On if you want to control settings

before committing the job to the printer. See

Preview copies and scans

on page 15.

10.

When you have made your settings, press the Start Scan/Copy button

to

start copying.

8 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

See also:

●

Set and preview image adjustments on page 15

●

Set input and output sizes on page 13

●

Set the output quality on page 17

●

Set a destination folder for scans on page 6

Batch scan and batch copy

With batch scanning and batch copying you can continuously feed new originals

into the scanner and the system will start processing right away without waiting for

you to press the Start Scan/Copy button. The system will apply the current settings

to all documents. If you are scanning to file, your files will automatically be named

with increasing numbers.

1. Lay your originals face up, near the scanner so they are easily reached.

2. Make your scan or copy settings. These will apply for all the originals in the

batch.

3. Press the Batch Mode button to turn batch mode to On.

4.

Press the Start Scan/Copy button

.

5. If you have already loaded the first original, the system will start scanning or

copying. If not, the Batch Mode dialog will ask you to insert the first original

into the scanner.

6. When you insert the first original, the system will start scanning it right away.

10 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

7. When an original is scanned, it is ejected. The Batch Mode dialog returns and

asks for the next original.

8. Remove the ejected original and feed the next one.

9. Continue to feed originals until finished with the batch.

10. Press the Batch Mode dialog’s Cancel button to abort batch mode.

NOTE: Previewing is disabled when in Batch Mode.

NOTE: To ensure fast loading in batch mode, the scanner will automatically eject

each original after it is scanned. The setting in Options > Basic Options > Rewind

after scan will determine the direction. If the option is selected, scanned originals

will be ejected towards the front and if the option is not selected, scanned originals

will be ejected out the back.

Specify the original type and make image adjustments

Basic capture parameters are set when you select Original Type. You can then

adjust specific factors such as image brightness, sharpening and background

cleaning level. The adjustments available will depend on the Original Type

selection.

1. Press the Scan or Copy button and then the Original Type button to reach

the Original Type selection list.

2. Select an Original Type that best describes your original.

ENWW

Specify the original type and make image adjustments

11

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Original Type Description

Color Lines Suitable for color CAD drawings and graphics with a high level of detail.

Applies image processing to clean the background and sharpen lines. 24-bit

color scan.

Gray Lines Suitable for grayscale CAD drawings and graphics with a high level of detail.

Applies image processing to clean the background and sharpen lines. 8-bit

grayscale scan.

B&W Lines Suitable for clean B&W CAD drawings and graphics with a high level of detail.

Especially useful for scan-to-file as file sizes are minimal compared to color

and gray original types. Minimal application of image processing for a neutral

and fast scan.1-bit B&W scan.

Color Map Suitable for color maps such as topographic maps, road maps or other

document types that contain fill areas and a high level of detail. Applies image

processing to sharpen details. 24-bit color scan.

Gray Map Suitable for grayscale maps such as topographic maps, road maps or other

document types that contain fill areas and a high level of detail. Applies image

processing to sharpen details. 8-bit grayscale scan.

Color Poster Suitable for color photos and posters of good quality. Minimal application of

image processing for a neutral and fast scan. 24-bit color scan.

Old Drawing Suitable for faded and creased drawings with low contrast between the

foreground and background. Applies image processing to clean the

background and sharpen lines. 8-bit grayscale scan.

12 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

3. You can fine-tune the Original Type settings (optional): Press the More button

to expand the Original Type dialog and make adjustment options

relevant to the selected Original Type. Press OK when done.

4.

Press the Context-sensitive Help button

for additional information about

each setting and about saving your settings as a new custom Original Type.

NOTE: You can press the Preview Before Scan/Copy button and then the

Adjustment button to make image adjustments and view the effects on your screen.

See

Preview copies and scans on page 15.

Set input and output sizes

The "Scan Area" is your input size and defines how much of the image is captured.

Often, this will be equal to the total size of the original. However, there may be cases

when you only want to scan a portion of the original or wish the capture area to be

equal to a certain standard size.

When copying, you can also determine the output size (the size of the image in your

printed copy) through the Resize setting. You can choose No resize to use the

current Scan Area size for a 1:1 copy, or you can select a different size in order to

reduce or enlarge the printed image in relation to the Scan Area size.

NOTE: When scanning, the image’s size in the output file is always equal to the

Scan Area size (1:1).

Set the Scan Area (input size) for Copy and Scan

When in the Scan or Copy screens, press the Scan Area button to view the Scan

Area size list.

ENWW

Set input and output sizes

13

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

The list offers different methods you can use to determine the Scan Area size:

●

Auto: The program will automatically detect the size of the full document

loaded in the scanner. You can use the preview to check that the scanner has

detected the size correctly.

●

Use a standard or custom size: The dialog contains a list of standard sizes

and custom sizes saved on the system. Scroll through the list and select the

size you want to use. To create a new custom size, follow the instructions

below.

●

Set size values for width and length: Press the More button

to

expand the Scan Area dialog. Make your width and length size settings in the

fields or set Auto on width or length separately. You can save your changes

to create a new custom size or use them for the current job only.

NOTE: You can also set the Scan Area visually on the screen through a preview.

See

Preview copies and scans on page 15.

Set the Resize value (output size) for Copy only

1. Press the Resize button.

2. Select No if you do not want to resize the image: that is, you want the end

result to be the same size as the Scan Area.

3. Press the Size button to select a standard size (such as A2 or A4) from a list.

4. Select Scale to resize according to a scale factor (such as 50% or 32%).

14 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Preview copies and scans

You can preview your copies and scans before committing them to the printer or

file system. With previewing you can:

●

Make image adjustments that are relevant for your selected Original Type,

such as brightness and sharpening, and view the effects of these on your

screen.

●

Visually set the Scan Area (input size) using handles to drag and position a

Scan Area frame on the image.

●

Zoom in and out to evaluate specific image areas and the effects of your

settings.

Load a preview scan or copy

1. Load your original and press the Preview Before Scan/Copy button to turn

preview mode to On.

2. Press the Scan or Copy button to load the preview.

3.

You can at any time press the Cancel button

to close the preview.

Set and preview image adjustments

1.

Press the Adjustment button

at the top left corner of the preview screen.

2. Make your settings in the adjustments dialog.

3. Press the OK button to close the adjustments dialog and see the effects of

your settings on the preview. Use the zoom tools to inspect details and areas

of interest.

4. Repeat steps 1–3 if you need to readjust your settings.

NOTE: The effects of the image adjustment settings are applied and displayed in

the low-resolution preview and hence do not fully represent the final image in the

destination file or printed copy.

ENWW

Preview copies and scans

15

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Set and preview the scan area

The preview shows the image inside a white frame. The frame represents the

current Scan Area (input) size. Changing the frame’s size before scanning will

change the Scan Area settings. The frame's size can be adjusted by moving its

borders and corners. To do so you can:

●

Drag the resize handles

on the frame’s sides and corners.

●

Press with your finger on the place where you wish to reposition the nearest

border edge or corner. The border will jump to that place.

●

Use the image zoom and positioning tools to assist you in setting the frame

size and positioning the image inside of it. The image zoom and positioning

tools are:

Zoom crop: Snaps to the image as cropped by the borders.

Zoom in: Enlarge the image size in the preview. Zooming is targeted on

the center of the window.

Zoom out: Reduce the image size in the preview. Zooming is targeted on

the center of the window.

Zoom all: Displays the whole capture area without cropping. The borders

positions are defined by the current Original size setting.

Image panning tools: Use these arrows to center the captured image

in the window.

Frame center handle (blue circle): Use this to drag the whole size frame

and reposition it on the captured image.

Press the Start Scan/Copy button

when you are finished previewing and want

to commit the job.

Press the Cancel button

if you want to abort the preview process without

committing the job.

16 Chapter 2 Basic operations ENWW

Basic operations

Learning Products Barcelona - Hewlett-Packard Company

Stránka sa načítava ...

HP DesignJet T1120 SD Multifunction Printer series referenčná príručka

HP DesignJet T1120 SD Multifunction Printer series referenčná príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty