Dometic CAM 50 Návod na používanie

Typ
Návod na používanie

Táto príručka je tiež vhodná pre

CAM50
Rear View Video Camera
Installation and Operating Manual. . . . . . . . 9
Rückfahrvideokamera
Montage- und Bedienungsanleitung . . . . .23
Caméra vidéo de recul
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . .37
Cámara de vídeo de marcha atrás
Instrucciones de montaje y de uso . . . . . . .52
Câmara de marcha-atrás
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Videocamera per la retromarcia
Istruzioni di montaggio e d’uso . . . . . . . . . 81
Achteruitrijvideocamera
Montagehandleiding en
gebruiksaanwijzing . . . . . . . . . . . . . . . . . . .95
Bakvideokamera
Monterings- og betjeningsvejledning . . .109
Backningsvideokamera
Monterings- och bruksanvisning . . . . . . .122
Ryggevideokamera
Monterings- og bruksanvisning . . . . . . . .135
Peruutusvideokamera
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 148
Видеокамера заднего вида
Инструкция по монтажу
и эксплуатации . . . . . . . . . . . . . . . . . . . . . 162
Kamera cofania
Instrukcja montażu i obsługi. . . . . . . . . . . 177
Cúvacia kamera
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 191
Couvací kamera
Návod k montáži a obsluze . . . . . . . . . . . 204
Tolatókamera
Szerelési és használati útmutató . . . . . . . 218
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
DRIVING SUPPORT
PERFECTVIEW
CAM50-IO-16S.book Seite 1 Donnerstag, 1. September 2016 3:16 15
CAM50-IO-16S.book Seite 2 Donnerstag, 1. September 2016 3:16 15
CAM50
3
1 2 3
4
9
6
8
5
7
10 11
12
1
CAM50-IO-16S.book Seite 3 Donnerstag, 1. September 2016 3:16 15
CAM50
4
2
3
4
5
6
7
CAM50-IO-16S.book Seite 4 Donnerstag, 1. September 2016 3:16 15
CAM50
5
1
3
2
5
6
4
8
3
2
1
9
CAM50-IO-16S.book Seite 5 Donnerstag, 1. September 2016 3:16 15
CAM50
6
90°
0
a
b
c
d
e
CAM50-IO-16S.book Seite 6 Donnerstag, 1. September 2016 3:16 15
CAM50
7
f
~50°
g
A B
h
i
A
B
j
CAM50-IO-16S.book Seite 7 Donnerstag, 1. September 2016 3:16 15
CAM50
8
k
CAM50-IO-16S.book Seite 8 Donnerstag, 1. September 2016 3:16 15
EN
CAM50
9
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Contents
1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
7 Notes on the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
8 Mounting the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
9 Cleaning and caring for the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
11 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CAM50-IO-16S.book Seite 9 Donnerstag, 1. September 2016 3:16 15
EN
Explanation of symbols CAM50
10
1 Explanation of symbols
!
!
A
I
2 Safety and installation instructions
Please observe the prescribed safety instructions and stipulations from the
vehicle manufacturer and service workshops.
The manufacturer accepts no liability for damage in the following cases:
Faulty assembly or connection
Damage to the product resulting from mechanical influences and excess voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
Please observe the following instructions:
To prevent short circuits, always disconnect the negative terminal of the vehicle’s
electrical system before working on it.
If the vehicle has an additional battery, its negative terminal should also be
disconnected.
Insufficient supply line connections could result in short circuits which
–Cause cable fires
Trigger the airbags
Damage electronic control devices
Cause electric functions to fail (indicators, brake light, horn, ignition, lights)
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
CAM50-IO-16S.book Seite 10 Donnerstag, 1. September 2016 3:16 15
EN
CAM50 Safety and installation instructions
11
When working on the following lines, only use insulated cable lugs, plugs and
tab sleeves:
30 (direct supply from positive battery terminal)
15 (connected positive terminal, behind the battery)
31 (return line from the battery, earth)
58 (reversing light)
Do not use porcelain wire connectors.
Use a crimping tool (fig. 1 10, page 3) to connect the cables.
When connecting to supply line 31 (earth), screw the cable
To the vehicle’s earth bolt with a cable lug and a gear disc or
To the sheet metal body work with a cable lug and a self-tapping screw.
Ensure that there is a good earth connection.
When the negative terminal of the battery is disconnected, all data stored in the
volatile memories will be lost.
The following data must be set again, depending on the vehicle equipment
options:
–Radio code
Vehicle clock
–Timer
On-board computer
Seat position
You can find instructions for making these settings in the appropriate operating
instructions.
Observe the following installation instructions:
Secure the parts of the camera installed in the vehicle in such a way that they
cannot become loose under any circumstances (sudden braking, accidents) and
cause injuries to the occupants of the vehicle.
Secure any parts of the system covered by the bodywork in such a manner that
they cannot be come loose or damage other parts and cables and impair vehicle
functions (steering, pedals, etc.).
To prevent damage, when drilling ensure that there is sufficient room for the drill
head to come out on the other side (fig. 2, page 4).
Deburr all drill holes and treat them with a rust-protection agent.
Always follow the safety instructions of the vehicle manufacturer.
Some work (e.g. on retention systems such as the AIRBAG etc.) may only be
performed by qualified specialists.
CAM50-IO-16S.book Seite 11 Donnerstag, 1. September 2016 3:16 15
EN
Safety and installation instructions CAM50
12
Observe the following instructions when working with electrical parts:
When testing the voltage in electrical cables, only use a diode test lamp
(fig. 1 8, page 3) or a voltmeter (fig. 1 9, page 3).
Test lamps with an illuminant (fig. 1 12, page 3) take up voltages which are too
high and which can damage the vehicle’s electronic system.
When making electrical connections, ensure that
They are not kinked or twisted
They do not rub on edges
They are not laid in sharp edged ducts without protection
(see fig. 3, page 4)
Insulate all connections.
Secure the cables against mechanical wear with cable binders or insulating tape,
for example to existing cables.
The camera is watertight. However, the sealings on the camera cannot withstand a
high-pressure cleaner (fig. 4, page 4). Therefore, you should observe the following
instructions when handling the camera:
People (including children) whose physical, sensory or mental capacities or
whose lack of experience or knowledge prevent them from using this product
safely should not use it without the supervision or instruction of a responsible
person.
Do not open the camera, as this impairs the sealing and the function of the
camera (fig. 5, page 4).
Do not pull at the cables, as this impairs the sealing and the function of the camera
(fig. 6, page 4).
The camera is not suitable for submerged operation (fig. 7, page 4).
CAM50-IO-16S.book Seite 12 Donnerstag, 1. September 2016 3:16 15
EN
CAM50 Scope of delivery
13
3Scope of delivery
4Accessories
Available as accessory (not included in scope of delivery):
5 Intended use
The CAM50C and CAM50CW colour cameras are primarily intended for use in
vehicles. They can be used in rear view video systems to observe the space directly
beside or behind the vehicle from the driver’s seat when manoeuvring or parking, for
example.
!
No. in
fig. 8, page 5
Quantity Description Ref. no.
11Camera
2 1 Camera bracket 9102200066
3 1 Camera guard 9102200067
42Side covers
5 1 Extension cable 9102200030
1 Fastening material
Description Ref. no.
Extension cable 5 m RV-805 9600000206
Extension cable 10 m RV-810 9600000207
Extension cable 20 m RV-820 9600000208
Spiral cable for trailer operation RV-150-SPK 9600000209
WARNING!
Risk of injury!
Since rear view systems are designed merely as an additional aid for
reversing, it does not relieve you of the duty to take proper care
when reversing.
CAM50-IO-16S.book Seite 13 Donnerstag, 1. September 2016 3:16 15
EN
Technical description CAM50
14
6 Technical description
The camera with integrated microphone, which is encased in aluminium housing,
transmits image and sound to a monitor via a cable. The built-in infrared LEDs
improve night vision.
The camera transmits the image as if you are looking in the rear mirror.
The camera consists of the following main elements:
7 Notes on the electrical connections
7.1 Laying cables
A
Please observe the following instructions:
As far as possible, use original openings or alternative openings for the
connecting cable duct, e.g. the paneling edges, ventilation grilles or blank
panels. If no openings are available, you must drill holes for the cables. Check
beforehand that there is sufficient room for the drill head to come out on the other
side.
No. in
fig. 9, page 5
Description
1 6-pin connection cable
2 Infrared LEDs
3 Microphone (back side)
NOTICE! Risk of damage!
To prevent damage, when drilling ensure that there is sufficient
space on the other side for the drill head to come out.
Cables and connections which are not properly installed will cause
malfunctions or damage to components. Correct installation of
cables and connections is the basic prerequisite for lasting and
trouble-free operation of the retrofitted components.
The cables may not be exposed for long periods to solvents such as
benzine, as the solvents can damage the cable.
CAM50-IO-16S.book Seite 14 Donnerstag, 1. September 2016 3:16 15
EN
CAM50 Notes on the electrical connections
15
Wherever possible lay cables inside the vehicle, as they are better protected
inside than outside the vehicle.
If you do need to lay a cable outside the vehicle, ensure that it is well secured
(use additional cable ties, insulating tape, etc.).
To prevent damage to the cables, when laying them ensure that there is sufficient
distance to hot or moving vehicle components (exhaust pipes, drive shafts, light
systems, fans, heater etc.). Use corrugated piping or other protective materials to
protect against mechanical wear.
Screw on the plug connections of the connecting cables to protect against water
penetration (fig. h, page 7).
When laying electric connections, ensure that
They are not kinked or twisted
They do not rub on edges
They are not laid in sharp edged ducts without protection (fig. 3, page 4)
Attach the cables securely in the vehicles to prevent tripping hazards. Use cable
binders, insulating tape or glue the cables in place.
Protect every through-hole made in the bodywork against water penetration,
e.g. by using a cable with a sealant and by spraying the cable and the cable
sleeve with sealant.
I
NOTE
Do not start sealing the through-holes until all installation work has been
finished for the camera, and the required cable lengths have been
established.
CAM50-IO-16S.book Seite 15 Donnerstag, 1. September 2016 3:16 15
EN
Mounting the camera CAM50
16
8Mounting the camera
8.1 Tools required
For installation and assembly you will require the following tools:
Drill bit set (fig. 1 1, page 3)
Drill (fig. 1 2, page 3)
Screwdriver (fig. 1 3, page 3)
Set of ring or open-ended spanners (fig. 1 4, page 3)
Measuring ruler (fig. 1 5, page 3)
Hammer (fig. 1 6, page 3)
Centre punch (fig. 1 7, page 3)
To make and test the electrical connection, the following tools are required:
Diode test lamp (fig. 1 8, page 3) or voltmeter (fig. 1 9, page 3)
Insulating tape (fig. 1 11, page 3)
Cable bushing sleeves, if necessary
To fasten the cables you may require additional cable binders.
8.2 Mounting the camera
!
I
CAUTION!
Select a location for the camera and attach it so securely that it cannot
under any circumstances fall off and injure bystanders (e.g. by being
knocked off by branches brushing over the roof of the vehicle).
NOTE
If installing the camera alters the vehicle height or length specified in the
vehicle documents, your vehicle must be inspected by the appropriate
authorities.
Make sure that you are in possession of documents verifying that your
vehicle has passed this inspection.
CAM50-IO-16S.book Seite 16 Donnerstag, 1. September 2016 3:16 15
EN
CAM50 Mounting the camera
17
Observe the following installation instructions:
To provide a suitable viewing angle, the camera must be attached at a height of
at least 2 m.
Ensure that you have a firm place from which to work when mounting the camera.
Ensure that the installation location of the camera is sufficiently firm (e.g. to
prevent the camera from being knocked down by branches that may brush over
the roof of the vehicle).
Mount the camera bracket horizontally and in the middle of the rear of the vehicle
(fig. 0, page 6).
The most secure type of attachment is with screws fitted through the body.
Please observe the following instructions:
There must be sufficient space for the mounting procedure behind the
chosen installation location.
Suitable measures must be taken to prevent water penetrating through any
holes made (e.g. by using screws and sealant and/or spraying the outer
attachment parts with a sealant).
The location on the body where you wish to attach the camera must be rigid
enough to allow the camera to be tightly fastened.
Check beforehand that there is sufficient room for the drill head to come out on
the other side (fig. 2, page 4).
If you are not sure about the location you have chosen, consult the vehicle
manufacturer or dealer.
I
When mounting the camera, proceed as follows:
Hold the camera on the chosen location and mark at least two different points for
the drill holes (fig. a, page 6).
Using a hammer and centre punch, gently pre-punch the previously marked
points to prevent the drill head from slipping off.
NOTE
We recommend greasing the threads of the bolts to prevent corrosion.
CAM50-IO-16S.book Seite 17 Donnerstag, 1. September 2016 3:16 15
EN
Mounting the camera CAM50
18
If you want to screw on the camera with self-tapping screws
(fig. b, page 6)
A
Drill Ø 2 mm holes at the points you have just marked.
Deburr all drill holes and apply rust-protection.
Screw the camera bracket on with the 3 x 10 mm self-tapping screws.
If you would like to attach the camera with threaded screws fitted through
the construction (fig. c, page 6)
A
Drill Ø 3.5 mm holes at the points you have just marked.
Deburr all drill holes and apply rust-protection.
Screw the camera bracket on with the M3 x 20 mm threaded screws.
Depending on the thickness of the construction, you may require longer
threaded screws.
NOTICE! Risk of damage!
The holder may only be attached to steel panels with a minimum
thickness of 1.5 mm using self-tapping screws.
NOTICE! Risk of damage!
Ensure that that nuts cannot be pulled through the body shell when they
are tightened.
Use larger washers or metal plates if necessary.
CAM50-IO-16S.book Seite 18 Donnerstag, 1. September 2016 3:16 15
EN
CAM50 Mounting the camera
19
Creating a through-hole for the camera connection cable
(fig. d, page 6)
I
A
Drill a hole of Ø 16 mm near the camera.
Deburr all drill holes that have been made in the sheet metal and apply
rust-protection.
Place cable sleeves in all sharp edged ducts.
Mounting the camera
A
Push the camera into the camera bracket.
Attach the camera loosely with the two screws M3 x 6 mm in the slots (fig. e,
page 6).
Align the camera provisorily so that the lens is at an angle of approx. 50° to the
perpendicular axis of the vehicle (fig. f, page 7).
A
Push the camera guard over the camera (fig. g, page 7)
NOTE
If possible, use available openings – such as ventilation grilles – to feed
the connection cables through. If there are no existing openings, you
must drill a hole with a 16 mm diameter.
NOTICE! Risk of damage!
Ensure that there is sufficient space on the other side for the drill head to
come out
NOTICE! Risk of damage!
Only use the screws supplied to mount the camera in the camera
bracket. Longer screws will damage the camera.
NOTICE! Risk of damage!
Never mount the camera without the camera guard.
CAM50-IO-16S.book Seite 19 Donnerstag, 1. September 2016 3:16 15
EN
Mounting the camera CAM50
20
Connecting the camera
I
Guide the camera cable into the vehicle interior.
Insert the plug of the camera cable into the socket of the extension cable.
Screw on the plug connections of the connecting cables to protect against water
penetration (fig. h, page 7).
Aligning the camera
I
Use the monitor image to align the camera:
The monitor image should show the bottom edge of the rear or the bumper of
your vehicle (A). The middle of the bumper should be in the middle of the
screen. (fig. j, page 7).
Check the function of the camera after you have connected it to a monitor.
Fastening the camera
Thighten the two screws in the slots of the camera bracket.
Mount the side covers with the two screws M3 x 8 mm in the middle drill holes
(fig. k, page 8).
NOTE
Lay the camera cable so that should you need to remove the camera,
you can access the plug connection between the camera and the
extension cable easily. This considerably eases dismantling work.
To minimise corrosion in the plug, apply a small amount of grease –
such as pin grease – inside the plug.
Additional extension cables are available on request (see chapter
“Accessories” on page 13).
NOTE
If necessary before aligning the camera connect the camera to a monitor
and to a power supply (see connecting diagram, fig. i, page 7
CAM50-IO-16S.book Seite 20 Donnerstag, 1. September 2016 3:16 15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232

Dometic CAM 50 Návod na používanie

Typ
Návod na používanie
Táto príručka je tiež vhodná pre