Electrolux EHG686X Používateľská príručka
- Kategória
- Varné dosky
- Typ
- Používateľská príručka
Piani di cottura - Built-in hobs
35677-4301
ISTRUZIONI PER L'USO E L'INSTALLAZIONE
INSTRUCTION BOOKLET
IT
Mod. EHG 686
11
About Installation, Cleaning and
Manteinance
It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance work.
Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
Ensure that the gas supply complies with the gas type
stated on the identification label, placed near the gas
supply pipe.
Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable is
in perfect conditions. Otherwise, contact your dealer
before proceeding with the installation.
The manufacturer disclaims any responsability
should all the safety measures not be carried out.
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Child Safety
This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or play
near or with the oven.
Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until it
has cooled.
English
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
Important Safety Information
During Operation
It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred, always
ensure that the book is left with the appliance in order
that the new owner can get to know the functions of the
appliance and the relevant warnings.
This appliance has been designed for non professional
purpose in private houses only. It is meant to cook
edible foodstuff only and MUST NOT be used for any other
purposes.
It is dangerous to alter the specification in any way.
For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
Ensure that all control knobs are in the OFF position
when not in use.
Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables are
not in contact with it and keep them far enough from
the heated parts of this appliance.
If the appliance is out of order, disconnect it from the
electric supply.
Environmental Information
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
12
Contents
For the User
This appliance complies with the following
E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336
(Electromagnetical Compatibility Directive);
- 93/68 (General Directives)
and subsequent modifications.
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental information
F
Guide to Use the instructions
For the Installer
These instructions are only for the countries
stated by the symbol printed on the front cover
of this instruction book.
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna 298 - 47100 FORLI (Italy)
Important Safety Information 11
Guide to Use the instructions 12
Instruction for the User 13
Cleaning and Maintenance 14
Technical Data 15
Electrical Connection 16
Adaptation to different types of gas 17
Building In 18
Possibilities for insertion 19
13
Once the hob has been installed, it is
important to remove any protective materials,
which were put on in the factory.
Hob burners control knobs
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that:
l there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
F
To light a burner:
l push in the relevant knob and turn it anticlockwise to
"maximum position".
l After lighting the flame, keep the knob pushed down
for about 5 seconds. This will allow the "thermocouple"
(Fig. 1, lett. C) to be heated and the safety device to
be switched off, otherwise the gas supply would be
interrupted.
l Then, check the flame is regular and adjust it as
required.
l If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1, lett. A) is in the
correct position.
To put the flame out, turn the knob to the symbol l.
Always turn the flame down or put it out before
taking the pans off the burner.
Burner minimum maximum
diameter diameter
Big (rapid) 160 mm. 260 mm.
Medium (semirapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.
Instruction for the User
A - Burner cap
B - Ignition candle
C - Thermocouple
Using the hob correctly
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame will
not spread beyond the bottom of the vessel.
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom..
Carefully supervise cookings with fats or
oil, since these types of foodstuff can result
in a fire, if over-heated.
Fig. 1
FO 2295
14
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
General cleaning
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
The cap and crown of each burner are secured
with two screws. To separate the two pieces, lift
the cap, turn it upside down, then undo the two
fixing screws as shown in fig. 3.
Regularly wipe over the hob top using a soft cloth weel
wrung out in warm water to which a little liquid detergent
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a proper cleaning product is used.
Pan supports
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
Ignition candle
The electric ignition is obtained through a ceramic
"candle" and a metal electrode (fig.1-lett. B). Keep these
components well clean, to avoid difficult lighting, and
check that the burner crown holes are not obstructed.
Periodic Maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
l The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
Service and original spare parts
This machine, before leaving the factory, has been
tested and studied by many experts and specialists, in
order to give you the best results.
Any repair work which needs to be carried out should
be done with the utmost care and
attention.
For this reason we reccomend
that for any problem you contact
the dealer who sold it to you, or
our nearest authorized Service
Centre, specifying the nature of
the problem and the particular
model which you own. Always
Insist on genuine original spare parts.
Fig. 2
FO 2265
Fig. 3
15
Gas Burners Rating
Rapid Burner 3,0 kW (GN) - 2,8 (GPL)
Auxiliary Burner 1 kW
Semirapid Burner 2 kW
Appliance Class 3
Category II 2H3+
Setting Natural gas G 20 / 20 mbar
Gas connection G 1/2"
l The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force.
l The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
l Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
l The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are followed.
THE MANUFACTURER WILL NOT ACCEPT
LIABILITY, SHOULD ANY OF THE OTHER SAFETY
INSTRUCTIONS INCORPORATED IN THIS BOOK
OR THE REGULATION IN FORCE BE IGNORED.
Technical Data
Instruction for the Installer
Electric Supply
230 V 50 Hz
Hob recess dimensions
Length 550 mm.
Width 470 mm.
Gas connection
Choose fixed connections or use a flexible pipe in
stainless steel in compliance with the regulation in force.
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut GJ 1/2". Interpose the
sealing between the components as shown in fig. 4.
Screw the parts without forcing, adjust the connection in
the required direction and tighten everything.
IMPORTANT - When the final connection has
been made, it is essential that a thorough leak
test is carried out on the hob and installation.
Use some soapy water, never a flame.
Fig. 4
FO 0264
A) Ramp with ending nut
B) Seal
C) Adjustable connection
16
The appliance is designed to be connected to 230 V
monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Before the appliance is connected:
1) check that the main fuse and the domestic installation
can support the load (see the rating label);
2) check that the power supply is properly earthed in
compliance with the current rules;
3) check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a connection cable. This
has to be provided with a proper plug, able to support the
load marked on the identification plate. To connect the
plug to the cable, follow the recommendation given in Fig.
5. The plug has to be fitted in a proper socket.
If connecting the appliance directly to the electric system,
it is necessary that you install a double pole switch
between the appliance and the electricity supply, with a
minimum gap of 3 mm. between the switch contacts and
of a type suitable for the required load in compliance with
the current rules.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature higher than 90
°C.
The brown coloured phase cable (fitted in the terminal
block contact marked with "L") must always be connected
to the network phase.
Replacement of the voltage cable
Only cable types H05V2V2-F T90 or H05 BB-F must be
used. The cable section must be suitable to the voltage
and the working temperature.
The yellow/green earth wire must be approximately 2
cm. longer than the phase wires (Fig. 6).
Fig. 6
FO 0073
Neutral
Earth (yellow/green)
Electrical Connection
Fig. 5
TUBO RIGIDO IN RAME
O FLESSIBILE IN
ACCIAIO INOX
FASCETTE
VISTA DAL RETRO
{
SI
Aperture
di servizio
ricavate
nel mobile
VISTA DAL RETRO
NO
FO 0238
YES
RIGID COPPER PIPE OR
FLEXIBLE PIPE IN STAINLESS
STEEL
17
Injectors replacement
Remove the pan supports.
Remove the burner's caps and crowns.
With a socket spanner 7 unscrew and remove the
injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see table 2).
Reassemble the parts, following the same procedu-
re backwards.
Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.
Fig. 7
FO 0392
Adjustment of minimum level
To adjust the minimum level of the burners, proceed as
follows:
Light the burner.
Turn the knob on the minimum position.
Remove the knob.
With a thin screwdriver, adjust the by-pass screw
(see Fig. 8). If changing from natural gas to LPG,
completely tighten clockwise the screw, until a
small regular flame is obtained. If changing from
LPG to natural gas unscrew about 1/4 turn the by-
pass screw, until a small regular flame is obtained.
Finally check the flame does not go out when
quickly turning the knob from the maximum position
to the minimum position.
This procedure can easily be carried out, anyhow the hob
has been positioned or built in the working top.
Burner Ø By-pass
in 1/100
of mm.
Auxiliary 28
Semi-rapid 32
Rapid 40
Table 1 : By-pass diameters
Table 2 : injectors
Adaptation to different types of gas
F
F
TYPE TYPE OF INJECTORS NOMINAL REDUCED NOMINAL NOMINAL
OF GAS BURNER MARKS POWER POWER POWER PRESSURE
1/100 mm INPUT kW mbar
KW m
3
/h g/h
Rapid (large) 119 3,0 0,65 0,286 -
Semi-rapid (medium) 96 2,0 0,45 0,190 - 20
Auxiliary (small) 70 1,0 0,33 0,095 -
Rapid (large) 86 2,8 0,65 - 202
Semi-rapid (medium) 71 2,0 0,45 - 144 28-30/37
Auxiliary (small) 50 1,0 0,33 - 72
NATURAL
GAS
G 20
LPG
(Buthane/
Propane)
By-pass screw
Fig. 8
18
Building In
These hobs can be inserted in a built-in kitchen unit
whose depth is between 550 and 600 mm. The hobs
dimensions are shown in Fig. 9.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 100 mm.
Hanging forniture units or hoods must be placed at 650
mm. minimum from the hob.
A = Auxiliary burner
SR = Semirapid burner
R = Rapid Burner
Fitting the hob to the worktop
The hobs can be installed in a kitchen unit with an
opening for insertion whose dimensions are shown in fig.
10. To install the hob, proceed as follows:
1) Remove the pan supports, the burners caps and
crowns and turn the hob upside down, taking care the
ignition candles are not damaged in this operation.
2) Place the sealing gasket (supplied with the hob) on
the edges of the cut out: place it exactly on the front
and rear edge, taking care that the sealings meet
without overlapping;
3) Fix the hob with the relevant screws (fig. 11). The
traction of the screws is able to trace the sealing, any
excess of which can be easily removed.
The edge of the hob forms a double labyrinth seal which
provides a total guarantee against infiltration of liquids.
Fig.10
Fig.11
a) sealing gasket
FO 2098
FO 0199
550
470
55 min.
30
a
500
580
SR
SR
R
A
Fig. 9
Dimensions are given in millimeters
19
a) Removable panel
b) Space possibly useful for
connections
550 min.
560 min.
Fig. 12
Fig. 13
Fig. 15
Fig. 16
FO 1013 FO 0947
FO 0198
Kitchen unit with door
Proper arrangements must be taken in designing the
forniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in Fig.
12.
The panel fitted under the hob should be easily
removable to allow an easy access if a technical
assistance intervention is needed.
Fig. 14
Kitchen unit with oven
The hob recess dimensions must comply the indication
given in Figs. 13 and 14 and must be provided with
brackets to allow a continuous supply of air.
To avoid overhating, the building in should be carried out
as shown in Figs. 15 e 16.
The hob's electric connection and the oven's one must
be carried out separately, both for safety reasons and
to allow the oven to be easily taken off the unit.
In case a hood with lenght of 600 mm. is fitted over the
hob, the hanging furniture units beside the hood must
be placed at 550 mm. minimum from the hob, to allow
the fitting and the correct use of the lid, if required (fig.
17).
30
20 min
60
a
b
Possibilities for insertion
FO 0939
FO 0938
120 cm
2
180 cm
2
360 cm
2
50 cm
2
650 mm
FO 2099
Fig. 17
470
30
591
380
140
595
02/02
Grafiche MDM - Forlì
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Electrolux EHG686X Používateľská príručka
- Kategória
- Varné dosky
- Typ
- Používateľská príručka
v iných jazykoch
- English: Electrolux EHG686X User manual
Súvisiace články
Ostatné dokumenty
-
Zanussi ZGS646ITX Používateľská príručka
-
-
Candy CHG6BFB4WB Používateľská príručka
-
Groupe Brandt TE516XS1 Návod na obsluhu
-
-
IKEA HB 660 S Užívateľská príručka
-
IKEA LHGA4K 501-560-08 Používateľská príručka
-
-