Makita HW001G Používateľská príručka

HW001G

EN Cordless High Pressure

Washer INSTRUCTION MANUAL 12

PL Akumulatorowa Myjka

Wysokociśnieniowa INSTRUKCJA OBSŁUGI 27

HU Akkumulátoros

nagynyomású mosó HASZNÁLATI KÉZIKÖNYV 43

SK Akumulátorový

vysokotlakový čistič NÁVOD NA OBSLUHU 58

CS Akumulátorová vysokotlaká

myčka NÁVOD K OBSLUZE 73

UK Акумуляторна мийка

високого тиску ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 88

RO

Dispozitiv de spălare

cu presiune ridicată cu

acumulator MANUAL DE INSTRUCŢIUNI 104

DE Akku Hochdruckreiniger BETRIEBSANLEITUNG 120

2

1

2

Fig.1

1

Fig.2

1

2

Fig.3

1

2

Fig.4

1

Fig.5

1

Fig.6

Fig.7

1

2

Fig.8

3

Fig.9

1

2

3

Fig.10

2 1

Fig.11

1

2

Fig.12

1

2

Fig.13

1

2

3

Fig.14

1

2

3

Fig.15

1

2

3

Fig.16

4

1

2

Fig.17

1

Fig.18

Fig.19

2

1

Fig.20

Fig.21

1

2

Fig.22

5

1

Fig.23

Fig.24

1

23

4

Fig.25

1

Fig.26

1

Fig.27

1

Fig.28

1

2

1

Fig.29

6

1

Fig.30

Fig.31

Fig.32

1

Fig.33

1

2

Fig.34

Fig.35

1

2

Fig.36

1

2

Fig.37

7

Fig.38

1

Fig.39

1

Fig.40

1 2 3

Fig.41

21

Fig.42

Fig.43

8

1

3

21416

17 20

18

19

21

22

23

15

4

5

6

7

8

9

10

11

12

13

Fig.44

Fig.45

9

1

2

Fig.46

Fig.47

Fig.48

Fig.49

Fig.50

Fig.51

Fig.52

10

Fig.53

Fig.54

2 3

1

Fig.55

Fig.56

Fig.57

Fig.58

1

2

Fig.59

Fig.60

11

Fig.61

12 ENGLISH

ENGLISH (Original instructions)

WARNING

• Machines shall not be used by children. Children should be

supervised to ensure that they do not play with the machine.

• This machine is not intended for use by persons (including chil-

dren) with reduced physical, sensory, or mental capabilities, or

lack of experience and knowledge.

• This machine has been designed for use with the cleaning agent

supplied or recommended by the manufacturer. The use of other

cleaning agents or chemicals may adversely aect the safety of

the machine.

• During use of high pressure cleaners, aerosols may be formed.

Inhalation of aerosols can be hazardous to health.

• Depending on the application, shielded nozzles can be used

for high pressure cleaning, which will reduce the emission of

hydrous aerosols dramatically. However, not all applications

allow the use of such a device. If shielded nozzles are not appli-

cable for the protection against aerosols, a respiratory mask of

class FFP 2 or equivalent may be needed, depending on the

cleaning environment.

• The employer shall perform a risk assessment in order to spec-

ify the necessary protective measures regarding aerosols,

depending on the surface to be cleaned and its environment.

Respiratory masks of class FFP 2, an equivalent or higher are

suitable for the protection against hydrous aerosols.

• High pressure jets can be dangerous if subject to misuse. The jet

must not be directed at persons, live electrical equipment or the

machine itself.

• Do not use the machine within range of persons unless they

wear protective clothing.

• Do not direct the jet against yourself or others in order to clean

clothes or foot-wear.

• Risk of explosion – Do not spray ammable liquids.

• High pressure cleaners shall not be used by children or

untrained personnel.

13 ENGLISH

• High pressure hoses, ttings and couplings are important for the

safety of the machine. Use only hoses, ttings and couplings

recommended by the manufacturer.

• To ensure machine safety, use only original spare parts from the

manufacturer or approved by the manufacturer.

• Always be sure that the machine is switched o and battery car-

tridges are removed before carrying out any work on the tool.

• Do not use the machine if important parts of the machine are

damaged, e.g. safety devices, high pressure hoses, trigger gun.

• Always remove the battery cartridges when leaving the machine

unattended.

• Comply with the requirements of the local water supply

company.

• For European countries:

According to EN12729 (BA), the appliance can also be con-

nected to the mains drinking water supply if a backow preventer

valve with drain facility is installed in the supply hose.

SPECIFICATIONS

Model: HW001G

Max. ow rate *1 7.0 L/min

Water ow rate *2 Mode 3 (High mode) 5.5 L/min

Mode 2 (Middle mode) 4.2 L/min

Mode 1 (Low mode) 3.0 L/min

Max. permissible pressure 11.5 MPa

Working pressure *2 Mode 3 (High mode) 8.5 MPa

Mode 2 (Middle mode) 5.5 MPa

Mode 1 (Low mode) 3.0 MPa

Max. feed pressure 1.0 MPa

Max. feed temperature 40 °C

Max. suction height 1.0 m

Rated voltage D.C. 36 V - 40 V max

Dimensions (L x W x H) *3 344 mm x 383 mm x 520 mm

Net weight 10.3 - 13.4 kg

Water protection IPX5

*1: When using the trigger gun without the nozzles.

*2: When using the vario spray nozzle and extension.

*3: When the handle is folded and without hoses.

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

14 ENGLISH

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040 / BL4050F* / BL4080F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Take particular care and attention.

Read instruction manual.

Do not connect to a potable water faucet.

Do not direct the jet at people including

yourself, animals, and live electrical

equipments.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

Intended use

This machine is intended for cleaning stubborn dirt by

using water jet. This machine is intended for both com-

mercial use and household use.

Noise

The typical A-weighted noise level determined accord-

ing to EN60335-2-79:

Sound pressure level (LpA) : 71 dB (A)

Uncertainty (K) : 3.2 dB (A)

The noise level under working may exceed 80 dB (A).

NOTE:

The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE:

The declared noise emission value(s) may

also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING:

The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is

used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60335-2-79:

Vibration emission (ah) : 3.2 m/s2

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

15 ENGLISH

Declarations of Conformity

For European countries only

The Declarations of conformity are included in Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious

injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

IMPORTANT SAFETY WARNINGS

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

WARNING – When using this product, basic pre-

cautions should always be followed, including the

following:

Work area safety

1. Keep operating area clear of all persons.

2. Do not overreach or stand on unstable sup-

ports. Keep good footing and balance at all

times.

3. Always place the high pressure washer body

on a level and stable surface. Avoid areas

where the ejected water will run or pool.

4. Before cleaning, check the surroundings and

objects to be cleaned. High pressure jets can

scrape away paint or other surface treatments

including toxic chemicals. Take the preventive

measures if necessary.

5. Be careful not to trip over by the hose of the

high pressure washer. Always be aware of the

conguration of the hose during operation.

6. During use, a small amount of water will come

out from the bottom of the high pressure

washer. Avoid locating the high pressure

washer in the areas where you don't want to

wet.

Personal safety

1. To protect against the jet and objects by the

jet, operators should wear appropriate cloth-

ing such as safety boots, safety gloves, safety

helmets with visors, hearing protection, etc.

2. Do not use the high pressure washer within

range of persons unless they wear protective

clothing.

3. To reduce the risk of injury, close supervision

is necessary when the product is used near

children.

4. If connection is made to a potable water sys-

tem, the system shall be protected against

backow.

5. Water that has owed through backow pre-

venter is considered to be non-potable.

Electrical safety

1. Never touch battery cartridges with wet hands.

2. Do not use the machine if the important parts

of the machine are damaged, e.g. safety

devices, high pressure hoses, or the trigger

gun.

Power tool use and care

1. Read all the instructions before using the

product.

2. Know how to stop the high pressure washer

and bleed pressures quickly. Be thoroughly

familiar with the controls.

3. High pressure jets can be dangerous if mis-

used. The jet must not be directed at people,

live electrical equipment, or the machine itself.

4. This machine is not intended for use by per-

sons (including children) with reduced physi-

cal, sensory, or mental capabilities, or lack of

experience and knowledge.

5. Children should be supervised to ensure that

they do not play with the appliance.

6. Do not spray ammable and/or toxic liquids.

This may cause an explosion, intoxication, or

damage to the machine.

7. Do not direct the jet against yourself or others

in order to clean clothes or foot-wear.

8. High pressure hoses, ttings and couplings

are important for the safety of the machine.

Use only hoses, ttings and couplings recom-

mended by the manufacturer.

9. Follow the instructions when changing

accessories.

10. Keep handles dry, clean, and free of oil or

grease.

11. Stay alert – watch what you are doing.

12. Do not operate the product when fatigued or

under the inuence of alcohol or drugs.

13. Do not run the high pressure washer without

water for longer than one minute. It will dam-

age the motor, resulting in malfunction.

14. Always turn o the power and shut o the

water mains when leaving the high pressure

washer unattended.

15. Be wary of the kickback. The trigger gun

recoils when the high pressure jet is ejected

from the nozzle. Hold the trigger gun rmly to

prevent accidental injuries.

16. Check for damaged or worn parts before use.

Also make sure that the hose is properly con-

nected and there is no leakage during oper-

ation. Operating the machine with functional

defects may cause an accident.

16 ENGLISH

17. This machine has been designed for use with

the cleaning agent supplied or recommended

by the manufacturer. The use of other cleaning

agents or chemicals may adversely aect the

safety of the machine.

18. Do not pull the hose to move the high pressure

washer body. This will damage the hose and

connecting parts and result in a short circuit

or functional defects.

19. Do not put heavy objects on the hose or let

vehicles drive over it.

20. Always discharge the residual pressure in the

trigger gun before disconnecting the hose.

21. When connecting the hose to the water mains,

observe the instructions of your local water-

works department or company.

22. If the high pressure washer is dropped or hits

against an hard object, be sure to check for

damage and crack. Using the high pressure

washer damaged may generate smoke, re, or

cause electric shock, which result in personal

injury.

23. During use of high pressure cleaners, aerosols

may be formed. Inhalation of aerosols can be

hazardous to health.

24. Depending on the application, shielded noz-

zles can be used for high pressure cleaning,

which will reduce the emission of hydrous

aerosols dramatically. However, not all appli-

cations allow the use of such a device. If

shielded nozzles are not applicable for the pro-

tection against aerosols, a respiratory mask

of class FFP 2 or equivalent may be needed,

depending on the cleaning environment.

25. The employer shall perform a risk assessment

in order to specify the necessary protective

measures regarding aerosols, depending on

the surface to be cleaned and its environment.

Respiratory masks of class FFP 2, an equiv-

alent or higher are suitable for the protection

against hydrous aerosols.

26. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to battery pack, picking up or carrying the

appliance. Carrying the appliance with your nger

on the switch or energizing appliance that have

the switch on invites accidents.

27. Disconnect the battery pack from the appli-

ance before making any adjustments, chang-

ing accessories, or storing appliance. Such

preventive safety measures reduce the risk of

starting the appliance accidentally.

28. Do not modify or attempt to repair the appli-

ance or the battery pack except as indicated in

the instructions for use and care.

29. Do not apply the water jet to the same area

continuously. The object may break and cause

an injury.

30. Do not wash the machine with the water jet of

this machine. The machine may break or parts of

the machine may come o and cause an injury.

31. To avoid risk of electric shock, do not direct

the water jet against the machine while the

machine is turned on.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

Service

1. Follow the maintenance instructions specied

in the manual.

2. To ensure machine safety, use only original

spare parts from the manufacturer or approved

by the manufacturer.

3. Have your high pressure washer serviced by

a qualied repair person using only identi-

cal replacement parts. This will ensure that

the safety of the high pressure washer is

maintained.

4. In case of breakdown or malfunction of the

high pressure washer, immediately switch

it o and remove the battery cartridge(s).

Contact your local dealer or service center.

Additional safety warnings

1. Comply with the requirements of the local

water supply company.

2. Do not use the machine when there is a risk of

lightning.

3. When you use the machine on muddy ground,

wet slope, or slippery place, pay attention to

your footing.

4. Do not replace the battery in the rain.

5. Do not submerge the machine into a puddle.

6. Do not leave the machine unattended outdoors

in the rain.

7. When storing the machine, avoid direct sun-

light and rain, and store it in a place where it

does not get hot or humid.

17 ENGLISH

8. Do not sit on the machine or use the machine

as a step stool. Doing so may cause accident or

malfunction of machine.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper with the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

18 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the machine

is switched o and the battery cartridges are

removed before adjusting or checking function on

the machine.

Installing or removing battery

cartridge

CAUTION: Always switch o the machine

before installing or removing of the battery

cartridge.

CAUTION: Hold the machine and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the machine and the

battery cartridge rmly may cause them to slip o

your hands and result in damage to the machine and

battery cartridge and a personal injury.

CAUTION: Make sure that you lock the battery

cover before use. Otherwise, mud, dirt, or water may

cause damage to the product or the battery cartridge.

CAUTION: Always install the battery cartridge

fully. If not, it may accidentally fall out of the machine,

causing injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

CAUTION: Hold the battery cover rmly when

installing or removing the battery cartridge.

To install the battery cartridge;

1. Pull up the locking lever, and then open the battery

cover.

► Fig.1: 1. Battery cover 2. Locking lever

2. Align the tongue on the battery cartridge with the

slot on the machine, and then slide the cartridge until it

locks in place with a little click.

► Fig.2: 1. Battery cartridge

3. Close the battery cover and push it until it is

latched with the locking lever.

To remove the battery cartridge;

1. Pull up the locking lever and open the battery

cover.

2. Pull out the battery cartridge from the machine

while sliding the button on the front of the cartridge.

3. Close the battery cover and push it until it is

latched with the locking lever.

Battery check button

You can check the remaining battery capacity by press-

ing the battery check button.

► Fig.3: 1. Battery indicator 2. Battery check button

Battery indicator status Remaining

battery

capacity

On O Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE: The indicator lamp for remaining battery

capacity is just for a reference. The actual battery

capacity may dier depending on the usage condi-

tions or ambient temperature.

NOTE:

The lamp automatically goes o after a few seconds.

NOTE: If two battery cartridges are installed, the

battery installed on the left side is used rst.

NOTE: If two battery cartridges are installed, the

machine automatically switches the battery when the

battery in use becomes empty.

NOTE: You can check the remaining battery capacity

without turning on the power switch.

Indicating the remaining battery capacity

Press the check button on the battery cartridge to indicate the remain-

ing battery capacity. The indicator lamps light up for a few seconds.

► Fig.4: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

19 ENGLISH

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Machine/battery protection system

The machine is equipped with a machine/battery

protection system. This system automatically cuts o

power to the motor to extend machine and battery life.

The machine will automatically stop during operation if

the machine or battery is placed under one of the fol-

lowing conditions:

Overload protection

When the machine or battery is operated in a manner

that causes it to draw an abnormally high current, the

machine automatically stops and the speed indicator

blinks in green. In this situation, turn the machine o

and stop the application that caused the machine to

become overloaded. Then turn the machine on to

restart.

Overheat protection

When the machine is overheated, the machine stops

automatically and the speed indicator lights up in red. In

this case, let the machine and battery cool before turn-

ing the machine on again.

NOTE: The speed indicator blinks in red when the

battery is overheated.

Overdischarge protection

When the battery capacity is not enough, the machine

stops automatically and the speed indicator blinks in

red. In this case, remove the battery from the machine

and charge the battery or change the battery to fully

charged one.

Protections against other causes

Protection system is also designed for other causes that

could damage the machine and allows the machine to

stop automatically. Take all the following steps to clear

the causes, when the machine has been brought to a

temporary halt or stop in operation.

1. Turn the machine o, and then turn it on again to

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the machine and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

NOTICE: If the machine stops due to a cause

not described above, refer to the section for

troubleshooting.

Mode switching button

The speed can be changed in three levels. To change

the speed mode, press the mode switching button.

When you change the speed mode, the corresponding

speed indicators light up.

► Fig.5: 1. Mode switching button

NOTE: You cannot change the mode while the

machine is turned on. Change the mode when the

machine is turned o and the battery is installed to

the machine.

NOTE: If the speed indicator lights up in red or blinks

in red or green, refer to the instructions for machine/

battery protection system.

Power switch

WARNING: Always turn o the main power

switch when not in use.

NOTICE: Do not turn the power switch forcibly.

This may cause the switch to malfunction.

To turn on the machine, turn the power switch clock-

wise, and to turn o the machine, turn the power switch

counterclockwise.

► Fig.6: 1. Power switch

NOTE: The battery indicators will light up for a few

seconds just after turning the machine on.

NOTE: If you install the battery cartridge to the

machine when the power switch is in the turned-on

position, the speed indicator blinks in green. Turn

the power switch to the turned-o position, and then

install the battery cartridge to the machine.

Nozzle functions

NOTE: The standard nozzles may vary depending on

the country. Refer to the section for optional accesso-

ries for other nozzles.

Cyclone jet nozzle

Country specic

NOTICE: Do not use the cyclone jet nozzle to

clean fragile surfaces such as windows or car

bodies.

► Fig.7

A spiral jet is ejected. Suitable for removing stubborn

dirt.

20 ENGLISH

Vario spray nozzle and extension

Country specic

CAUTION: Install only the vario spray noz-

zle to the extension. Do not connect the other

optional extensions to the original extension.

Using any attachments other than those recom-

mended by the manufacturer may cause a risk of

damage or injury to persons.

CAUTION: When adjusting the jet pressure,

do not rotate the nozzle while pulling it toward the

trigger gun. The nozzle may come o from the trig-

ger gun and cause a personal injury.

CAUTION: When rotating the tip of the nozzle

to adjust the water jet, do not rotate it forcibly.

Otherwise, the nozzle may break and cause an injury.

► Fig.8: 1. Vario spray nozzle 2. Extension

Jet pressure can be adjusted by rotating the nozzle.

NOTICE: When turning the nozzle, do not hold

the tip of the nozzle, but hold the root of the noz-

zle as shown in the gure.

► Fig.9

NOTE: The vario spray nozzle can also be directly

attached to the trigger gun.

Trigger operation

NOTICE: To avoid mechanical error in the pres-

sure switch, always leave a two-second interval

between trigger operations.

Pull the trigger to eject a water jet. The jet continues as

long as the trigger is squeezed.

The trigger can be locked for safe handling of the trigger

gun. To lock the trigger, pull out the stopper and hook it

to the groove on the grip.

► Fig.10: 1. Trigger 2. Stopper 3. Groove

ASSEMBLY

WARNING: Always be sure that all the battery

cartridges are removed before carrying out any

work on the machine. Failure to remove all the bat-

tery cartridges may result in serious personal injury

from accidental start-up.

Connecting the high-pressure hose

CAUTION: Make sure that the high-pressure

hose is securely connected. A loose connection

may blow the high-pressure hose o, resulting in a

personal injury.

Connect the high-pressure hose to the outlet. Turn the

nut on the high-pressure hose clockwise while screwing

it onto the screw thread of the outlet.

► Fig.11: 1. Outlet 2. Nut

Attaching the trigger gun

CAUTION: Make sure that the high-pressure

hose is securely connected. A loose connection

may blow the high-pressure hose o, resulting in a

personal injury.

Connect the high-pressure hose to the inlet on the trig-

ger gun. Turn the nut on the high-pressure hose clock-

wise while screwing it onto the screw thread on the inlet.

► Fig.12: 1. Inlet 2. Nut

Connecting to a faucet

CAUTION: Always use a pressure-resistant

water hose with the following diameters and

connect to the faucet using a proper ttings.

Otherwise, the water hose and/or the tting may

break and cause personal injury.

• Inner diameter of hose is 14 mm to 15 mm.

• Outer diameter of hose is 20 mm or less.

• Thickness of hose is 2.3 mm or more and less

than 3.0 mm.

NOTICE:

Use a pressure-resistant water hose as

short as possible. The amount of intake water should

be higher than the max feed volume of the pump.

NOTICE: If you connect to the mains for drink-

ing water, use a backow preventer valve which

meets the regulations in your region.

NOTICE: When connecting to a faucet, the

required water ow rate is 7.0 L/min or more. If the

water ow rate is insucient, you cannot obtain the

full capability of the machine.

NOTE: The hose assembly ships with coupling

sleeves attached to both ends. When connecting to a

faucet without a coupling sleeve, remove the coupling

sleeve at one end by turning the coupling sleeve in

the direction of the arrow shown in the gure.

► Fig.13:

1. Nut of the coupling sleeve 2. Coupling sleeve

1. Connect the hose assembly to the faucet. Apply

a suitable tting such as hose band or water tap joint to

secure the hose end with the faucet.

► Fig.14: 1. Hose band 2. Coupling sleeve 3. Hose

assembly

NOTICE: Connect the hose assembly to the

faucet securely. Otherwise, the hose assembly may

come o when you open the faucet.

NOTE: The tting depends on the shape of the faucet

to which you connect. Prepare a suitable commercial-

ly-bought tting.

2.

Attach the water hose connector to the inlet, and then

attach the coupling sleeve to the water hose connector.

► Fig.15:

1. Coupling sleeve 2. Water hose connector 3. Inlet

NOTICE: When attaching the water hose con-

nector and coupling sleeve, attach them securely.

Otherwise, the water hose connector or coupling

sleeve may come o when you open the faucet.

Stránka sa načítava ...

Makita HW001G Používateľská príručka

Makita HW001G Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty