Sonicare HX9142/32 Používateľská príručka

FlexCare Platinum

1

Sonicare FlexCare Platinum

ENGLISH 6

БЪЛГАРСКИ 20

ČEŠTINA 37

EESTI 51

HRVATSKI 65

MAGYAR 79

ҚАЗАҚША 94

LIETUVIŠKAI 109

LATVIEŠU 123

POLSKI 136

ROMÂNĂ 152

РУССКИЙ 167

SLOVENSKY 184

SLOVENŠČINA 198

SRPSKI 211

УКРАЇНСЬКА 226

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at

www.philips.com/welcome.

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Keep the charger and/or sanitiser away from

water. Do not place or store it over or near water

contained in a bathtub, washbasin, sink etc. Do not

immerse the charger and/or sanitiser in water or

any other liquid. After cleaning, make sure the

charger and/or sanitiser is completely dry before

you connect it to the mains.

Warning

- The mains cord cannot be replaced. If the mains

cord is damaged, discard the charger and/or sanitiser.

- Always have the charger and/or sanitiser replaced

with one of the original type in order to avoid a

hazard.

- Do not use the charger and/or sanitiser outdoors

or near heated surfaces. Do not operate the

sanitiser where aerosol (spray) products are being

used or where oxygen is being administered.

- The appliance is suitable for mains voltages

ranging from 100 to 240 volts.

ENGLISH

- If the appliance is damaged in any way (brush

head, toothbrush handle, charger and/or sanitiser),

stop using it. This appliance contains no

serviceable parts. If the appliance is damaged,

contact the Consumer Care Centre in your

country (see chapter ‘Guarantee and support’).

- This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall

not be made by children unless they are older

than 8 and supervised.

- Discontinue use of the sanitiser if the UV light bulb

remains on when the door is open. UV light can be

harmful to the human eye and skin. Keep the

sanitiser out of the reach of children at all times.

Caution

- Do not clean the brush head, the handle, the

charger and/or the sanitiser in the dishwasher.

- If you have had oral or gum surgery in the

previous 2 months, consult your dentist before

you use the toothbrush.

ENGLISH 7

- Consult your dentist if excessive bleeding occurs

after using this toothbrush or if bleeding continues

to occur after 1 week of use. Also consult your

dentist if you experience discomfort or pain when

you use the Sonicare.

- The Sonicare toothbrush complies with the safety

standards for electromagnetic devices. If you have

a pacemaker or other implanted device, contact

your physician or the device manufacturer of the

implanted device prior to use.

- If you have medical concerns, consult your doctor

before you use the Sonicare.

- This appliance has only been designed for cleaning

teeth, gums and tongue. Do not use it for any

other purpose. Stop using the appliance and

contact your doctor if you experience any

discomfort or pain.

- The Sonicare toothbrush is a personal care device

and is not intended for use on multiple patients in

a dental practice or institution.

- Stop using a brush head with crushed or bent

bristles. Replace the brush head every 3 months

or sooner if signs of wear appear.

- Do not use other brush heads than the ones

recommended by the manufacturer.

- If your toothpaste contains peroxide, baking soda

or bicarbonate (common in whitening

ENGLISH8

toothpastes), thoroughly clean the brush head

with soap and water after each use. This prevents

possible cracking of the plastic.

- Do not insert objects into the air openings of the

sanitiser or block these air openings by placing it on

a soft surface or in a position or location where

objects will block these openings (examples of

objects: magazine, tissue paper and hair).

- The UV light bulb is hot during and immediately

after the sanitising cycle. Do not touch the UV

light bulb when it is hot.

- Do not operate the sanitiser without the protective

screen in place to avoid contact with a hot bulb.

- If the sanitiser has been used for 3 consecutive

UV clean cycles (i.e. 3 times in a row), switch it off

for at least 30 minutes before you start another

UV clean cycle.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic elds.

General description (Fig. 1)

1 Hygienic travel cap

2 Brush head with unique identier

3 Handle

4 Power on/off button

ENGLISH 9

5 Intensity level indicator

6 Intensity level button (+ and -)

7 Brushing modes

8 Mode button

9 Battery level indicator

10 UV sanitiser and base with integrated charger and cord wrap

(specic types only)

- Not shown: UV light bulb

- Not shown: Sanitiser drip tray

- Not shown: Protective screen for UV light bulb

11 Mains cord with plug

12 Charger cover with brush head holders (specic types only)

13 Travel charger

- Not shown: Travel case

Note: The contents of the box may vary based on the type purchased.

Preparing for use

Attaching the brush head

1 Align the brush head so the bristles face the front of the handle.

(Fig. 2)

2 Firmly press the brush head down on the metal shaft until it stops.

Note: Sonicare Platinum brush heads come with easily identiable icons to

identify your brush head.

Charging the appliance

1 Put the plug of the charger or sanitiser in a wall socket.

2 Place the handle on the charger (Fig. 3).

, The ashing light of the battery level indicator shows that the

toothbrush is charging.

ENGLISH10

Note: It takes at least 24 hours to fully charge the battery.

Using the appliance

Brushing instructions

1 Wet the bristles (Fig. 4).

2 Apply a small amount of toothpaste on the bristles. (Fig. 5)

3 Place the toothbrush bristles against the teeth at a slight angle

(45 degrees), pressing rmly to make the bristles reach the gumline

or slightly beneath the gumline. A change in vibration (and a slight

change in sound) alerts you when you apply too much pressure

while brushing (Fig. 6).

Note: Keep the centre of the brush in contact with the teeth at all times.

4 Press the power on/off button to switch on the Sonicare (Fig. 7).

5 Gently keep the bristles placed on the teeth and in the gumline.

Brush your teeth with small back and forth motions so the bristles

reach between the teeth (Fig. 8).

Note: The bristles should are slightly. Do not scrub.

6 To clean the inside surfaces of the front teeth, tilt the brush handle

semi-upright and make several vertical overlapping brushing strokes

on each tooth (Fig. 9).

7 Begin brushing in section 1 (outside top teeth) and brush for

30 seconds (45 seconds in Deep Clean mode) before you move to

section 2 (inside top teeth). Continue brushing in section 3 (outside

bottom teeth) and brush for 30 seconds (45 seconds in Deep

Clean mode) before you move to section 4 (inside bottom teeth).

Brush section 4 for 30 seconds until the toothbrush switches

off (Fig. 10).

ENGLISH 11

Note: To make sure you brush evenly throughout the mouth, divide the mouth

into 4 sections using the Quadpacer feature (see chapter ‘Features’).

Note: After you have completed the brushing cycle, you can spend additional

time brushing the chewing surfaces of your teeth and areas where staining

occurs. You may also brush your tongue, with the toothbrush switched on or

off, as you prefer (Fig. 11).

Your Sonicare is safe to use on:

- Braces (brush heads may wear out more quickly when used on braces).

- Dental restorations (llings, crowns, veneers, implants).

Brushing modes

1 Clean: For an exceptional everyday clean (default mode).

2 White: 2 minutes to remove surface stains and 30 seconds to

brighten and polish your front teeth.

3 Deep Clean: Provides an invigorating 3 minutes of alternating

cleaning and massaging to deliver an exceptionally clean experience.

Your Sonicare comes with the Clean mode activated.

Note: When the toothbrush is switched on, you cannot toggle between modes.

1 Before you switch on the Sonicare, press the mode button to

toggle between modes.

, The selected brushing mode lights up.

, Once a brushing mode has been selected, it remains active until

you select another brushing mode.

Note: When the Sonicare is used in clinical studies, it must be used in the

default 2-minute Clean mode at high intensity or in the Deep Clean mode at

high intensity.

Intensity levels per mode

- Low: 1 LED indicator light.

- Medium: 2 LED indicator lights.

- High: 3 LED indicator lights.

Note: to adjust the intensity level to the next higher or lower level, you can

press the + button to increase intensity or the - button to decrease intensity

at any time during the brushing cycle.

ENGLISH12

Pressure Sensor

A change in vibration (and a slight change in sound) alerts you when you

apply too much pressure while brushing. See chapter ‘Features’.

Battery status (when handle is not on charger)

- 1 yellow LED indicates a low charge.

- 3 green LEDs indicate a full charge.

Note: If you hear a long beep and the yellow LED of the battery level

indicator ashes, your toothbrush is completely empty and switches off.

Place the toothbrush on the charger to recharge it.

Note: To keep the battery fully charged at all times, you may keep your

Sonicare on the charger when not in use.

Features

Pressure Sensor

This Sonicare type comes with the Pressure Sensor feature activated.

The Pressure Sensor works in all 3 modes and at all 3 intensity levels.

To deactivate or reactivate the Pressure Sensor feature:

1 Place the handle with a brush head attached on the plugged-in

charger or sanitiser.

2 Press and hold the power on/off button and the mode button for

2 seconds.

, You hear 1 beep to indicate that the Pressure Sensor has been

deactivated.

, You hear 2 beeps to indicate that the Pressure Sensor has been

activated.

ENGLISH 13

Quadpacer

- The Quadpacer is an interval timer that has a short beep and pause

to remind you to brush the 4 sections of your mouth. Depending on

the brushing mode you have selected, the Quadpacer beeps at

different intervals during the brushing cycle. The Quadpacer works in

all 3 modes and at all 3 intensity levels (Fig. 10).

The Quadpacer feature on this type has been activated. To deactivate or

reactivate the Quadpacer feature:

1 Place the handle with a brush head attached on the plugged-in

charger or sanitiser.

2 Press and hold the mode button for 2 seconds.

, You hear 1 beep to indicate the Quadpacer has been deactivated.

, You hear 2 beeps to indicate the Quadpacer has been activated.

Smartimer

The Smartimer indicates that your brushing cycle is complete when

it automatically switches off the toothbrush at the end of the brushing cycle.

Dental professionals recommend brushing at least 2 minutes twice a day.

Easy-start

The Easy-start feature gently increases power over the rst 14 brushings

to ease into the Sonicare experience. The Easy-start feature only works in

the Clean mode and at the High intensity level.

This Sonicare type comes with the Easy-start feature deactivated.

To activate or deactivate the Easy-start feature:

1 Attach your brush head to the handle.

2 Place the handle on the plugged-in charger or sanitiser.

3 Activate or deactivate Easy-start:

, To activate Easy-start: Press and hold the power on/off button for

2 seconds. You hear 2 beeps to indicate that the Easy-start feature

has been activated.

ENGLISH14

, To deactivate Easy-start: Press and hold the power on/off button for

2 seconds. You hear 1 beep to indicate that the Easy-start feature has

been deactivated.

Note: Each of the rst 14 brushings must be at least 1 minute in length to

properly move through the Easy-start ramp-up cycle.

Note: Using the Easy-start feature beyond the initial ramp-up period is not

recommended and reduces Sonicare’s effectiveness in removing plaque.

Sanitising (specic types only)

- With the UV sanitiser you can clean your brush head after every use

(Fig. 12).

Unplug the sanitiser, discontinue use and call Consumer Care if:

- The UV light bulb remains on when the door is open.

- The window is broken or missing from the sanitiser.

- The sanitiser gives off smoke or a burning smell while it is operating.

Note: UV light can be harmful to the human eye and skin. Keep the sanitiser

out of the reach of children at all times.

1 After brushing, rinse the brush head for 15 seconds and shake off

excess water.

Do not place the travel cap on the brush head during sanitisation.

2 Let the brush head to dry in open air for 2 minutes.

3 Place your nger in the door recess on top of the sanitiser and pull

open the door (Fig. 13).

4 Place the brush head on one of the 2 pegs in the sanitiser with the

bristles facing the light bulb. (Fig. 14)

Note: Only clean Sonicare snap-on brush heads in the sanitiser.

Note: Do not clean Sonicare for Kids brush heads in the sanitiser.

5 Put the plug of the sanitiser in the wall socket.

6 Close the door and press the green power on/off button once to

select the UV clean cycle.

ENGLISH 15

Note: You can only switch on the sanitiser if the door is closed properly.

Note: The sanitiser stops if you open the door during the sanitising cycle.

Note: The sanitiser cycle runs for 10 minutes and then shuts off automatically.

, The sanitiser is in operation when the light glows through the window.

Cleaning

Do not clean the brush head, the handle, the travel charger, the charger

cover and the UV sanitiser in the dishwasher.

Toothbrush handle

1 Remove the brush head and rinse the metal shaft area with warm

water (Fig. 15).

Do not push on the rubber seal on the metal shaft with sharp objects,

as this may cause damage.

2 Use a damp cloth to wipe the entire surface of the handle.

Do not use isopropyl rubbing alcohol, vinegar, or essential oil based

products to clean the handle or the brush head.

Brush head

1 Rinse the brush head and bristles after each use (Fig. 16).

2 Remove the brush head from the handle and rinse the brush head

connection at least once a week with warm water.

UV sanitiser (specic types only)

Do not immerse the sanitiser in water or rinse it under the tap.

Do not clean the sanitiser when the UV light bulb is hot.

For optimal effectiveness, it is recommended to clean your sanitiser weekly.

1 Unplug the sanitiser.

2 Pull the drip tray straight out of the sanitiser. Rinse the drip tray

and wipe it clean with a damp cloth (Fig. 17).

ENGLISH16

3 Clean all interior surfaces with a damp cloth.

4 Remove the protective screen in front of the UV light bulb. (Fig. 18)

To remove the screen, grasp the edges next to the snaps, gently squeeze

and pull out the protective screen.

5 Remove the UV light bulb.

To remove the light bulb, grasp it and pull it out of the metal clasp.

6 Clean the protective screen and the UV light bulb with a damp cloth.

7 Reinsert the UV light bulb.

To reinsert the light bulb, align the bottom of the light bulb with the metal

clasp and push the bulb into the clasp.

8 Reinsert the protective screen.

To reinsert the screen, align the pegs on the screen with the slots on the

reective surface near the UV light bulb. Push the screen straight into the

slots on the sanitiser.

Storage

If you are not going to use the appliance for an extended period of time,

remove the mains plug from the wall socket. Then clean the appliance and

store it in a cool and dry place away from direct sunlight. You can use the

cord wrap feature to store the mains cord neatly.

Replacement

Brush head

Replace Sonicare brush heads every 3 months to achieve optimal results.

Only use genuine Philips Sonicare replacement brush heads.

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/

service or go to your Philips dealer. You can also contact the Philips

Consumer Care Centre in your country (see the worldwide guarantee

leaet for contact details).

ENGLISH 17

Recycling

- This symbol on a product means that the product is covered by

European Directive 2012/19/EU (Fig. 19).

- This symbol means that the product contains a built-in rechargeable

battery covered by European Directive 2006/66/EC which cannot be

disposed of with normal household waste. Follow the instructions in

section ‘Removing the rechargeable battery’ to remove the battery (Fig. 20).

- Inform yourself about the local separate collection system for

electrical and electronic products and rechargeable batteries. Follow

local rules and never dispose of the product and rechargeable

batteries with normal household waste. Correct disposal of old

products and rechargeable batteries helps prevent negative

consequences for the environment and human health.

Removing the rechargeable battery

Only remove the rechargeable battery when you discard the appliance.

Make sure the battery is completely empty when you remove it.

To remove the rechargeable battery, you need a at-head (standard)

screwdriver. Observe basic safety precautions when you follow the

procedure described below. Be sure to protect your eyes, hands, ngers,

and the surface on which you work.

1 Remove the toothbrush from the charger, switch it on and let it

operate until it stops. Continue to switch on the Sonicare until the

battery is completely empty.

2 Insert a athead (standard) screwdriver into the slot located at the

bottom of the handle. Turn the screwdriver anticlockwise to release

the bottom cap. (Fig. 21)

3 Place the handle on a solid surface with the buttons facing up and

lightly tap the housing 2.5cm from the bottom edge with a hammer.

4 Hold the handle upside down and push down on the shaft to

release the internal components of the handle (Fig. 22).

ENGLISH18

5 Insert the screwdriver under the circuit board, next to the battery

connections, and twist to break the connections. Remove the

circuit board and pry the battery from the plastic carrier (Fig. 23).

Guarantee and support

If you need information or support, please visit www.philips.com/

support or read the separate worldwide guarantee leaet.

Guarantee restrictions

The terms of the international guarantee do not cover the following:

- Brush heads.

- Damage caused by use of unauthorised replacement parts.

- Damage caused by misuse, abuse, neglect, alterations or unauthorised

repair.

- Normal wear and tear, including chips, scratches, abrasions,

discolouration or fading.

- UV light bulb.

ENGLISH 19

Въведение

Поздравления за вашата покупка и добре дошли във Philips! За да се

възползвате изцяло от предлаганата от Philips поддръжка,

регистрирайте продукта си на адрес www.philips.bg/welcome.

Важно

Преди да използвате уреда, прочетете

внимателно това ръководство за потребителя и

го запазете за справка в бъдеще.

Опасност

- Пазете зарядното устройство и/или уреда за

дезинфекция далеч от вода. Не го поставяйте

и не го съхранявайте над или в близост до

вода във вана, мивка, леген и т.н. Не потапяйте

зарядното устройство и/или уреда за

дезинфекция във вода или каквато и да е друга

течност. След почистване се уверете, че

зарядното устройство и/или уредът за

дезинфекция е напълно сух, преди да го

включите в контакта на електрическата мрежа.

Предупреждение

- Захранващият кабел не може да бъде заменян.

При повреда в кабела, зарядното устройство

и/или уредът за дезинфекция следва да се

изхвърли.

- С оглед на предотвратяване на злополука,

винаги заменяйте повреденото зарядно

устройство и/или уред за дезинфекция само с

оригинален такъв.

БЪЛГАРСКИ20

Stránka sa načítava...

Sonicare HX9142/32 Používateľská príručka

Tento návod je vhodný aj pre

Sonicare HX9142/32 Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty