ESAB A2 Origo™ Používateľská príručka

Kategória
Zvárací systém
Typ
Používateľská príručka
0458 817 027
041101
Control panel A2
Instruction manual Èíñòðóêöèÿ ïî ýêñïëóàòàöèè
-- 2 --
Rights reserved to alter specifications without notice.
Îñòàâëÿåì çà ñîáîé ïðàâî èçìåíÿòü ñïåöèôèêàöèþ áåç ïðåäóïðåæäåíèÿ.
Ðóññêèé 4...............................................
ENGLISH 6..............................................
3
bi06d1ra -- 4 --
1 ÂÂÅÄÅÍÈÅ
 íàñòîÿùåì ðóêîâîäñòâå ïðèâåäåíû óêàçàíèÿ ïî ðàáîòå ñ ïàíåëüþ
óïðàâëåíèÿ A2 , óñòàíîâëåííîé â ñâàðî÷íîì èñòî÷íèêå ïèòàíèÿ AristoArc 400,
AristoArc 500.
Îáùèå ñâåäåíèÿ ïî ýêñïëóàòàöèè ïðèâåäåíû â èíñòðóêöèÿõ ïî ýêñïëóàòàöèè
èñòî÷íèêà ïèòàíèÿ.
1.1 Ïàíåëü óïðàâëåíèÿ
1 Æåëòàÿ èíäèêàòîðíàÿ ëàìïà - Óêàçûâàåò íà
ëþáóþ íåèñïðàâíîñòü.
2 Ðó÷êà çàäàíèÿ ñâàðî÷íîãî òîêà
3 Ðó÷êà çàäàíèÿ ìîùíîñòè äóãè
1.2 Ïóëüò äèñòàíöèîííîãî óïðàâëåíèÿ
Ïóëüò äèñòàíöèîííîãî óïðàâëåíèÿ - ýòî óñòðîéñòâî, êîòîðîå ïîìèìî ïàíåëè
óïðàâëåíèÿ ìîæíî èñïîëüçîâàòü äëÿ ðåãóëèðîâêè îñíîâíûõ ïàðàìåòðîâ
ñâàðêè.
Äëÿ íàäëåæàùåãî ôóíêöèîíèðîâàíèÿ äèñòàíöèîííîãî óïðàâëåíèÿ íà
ìàøèíàõ Aristo ñî âñòðîåííûìè ïàíåëÿìè óïðàâëåíèÿ äîëæíà áûòü
óñòàíîâëåíà âåðñèÿ ïðîãðàììíîãî îáåñïå÷åíèÿ 1.21 èëè âûøå.
Åñëè ïóëüòà äèñòàíöèîííîãî óïðàâëåíèÿ, èñòî÷íèê ïèòàíèÿ íàõîäèòñÿ â
ðåæèìå äèñòàíöèîííîãî óïðàâëåíèÿ, è âñå êíîïêè è ðó÷êè óïðàâëåíèÿ
çàáëîêèðîâàíû. Ðåãóëèðîâêó âñåõ ôóíêöèé ìîæíî âûïîëíèòü òîëüêî ï ðè
ïîìîùè ïóëüòà äèñòàíöèîííîãî óïðàâëåíèÿ.
1.3 Ïàðàìåòðû
Ïàðàìåòðû AristoArc 400 AristoArc 500
Òîê 16 -- 400 A 16 -- 500 A
Ìîùíîñòü äóãè 0--10 0--10
Òîê
×åì âûøå ò îê, òåì øèðå è ãëóáæå ïðîíèêíîâåíèå â ñâàðèâàåìóþ äåòàëü.
Ìîùíîñòü äóãè
Îò ìîùíîñòè äóãè çàâèñèò, êàê áóäåò èçìåíÿòüñÿ òîê ïðè èçìåíåíèè äëèíû
äóãè. ×åì ìåíüøå ìîùíîñòü äóãè, òåì òèøå çâóê è ìåíüøå ðàçáðûçãèâàíèå.
RU
bi06d1ra -- 5 --
2 ÑÎÎÁÙÅÍÈß Î ÍÅÈÑÏÐÀÂÍÎÑÒßÕ
Åñëè ëàìïà: Ïðè÷èíà Äåéñòâèÿ:
èãàåò Îòñóòñòâèå ñîåäèíåíèÿ
ïàíåëè óïðàâëåíèÿ ñ
èñòî÷íèêîì ïèòàíèÿ.
S Ïðîâåðüòå êàáåëè. Ïîò ðåáóåòñÿ îòêëþ÷èòü
ïèòàíèå îò ñåòè, ÷òîáû ïåðåâåñòè ñèñòåìó â
èñõîäíîå ñîñòîÿíèå.
- ïîñòîÿííî
ãîðèò
Ñðàáîòàëî ðåëå çàùèòû
îò òåïëîâîé ïåðåãðóçêè.
S Ïðîâåðüòå, íå çàñîðèëñÿ ëè âîçäóøíûé
ôèëüòð.
Ñëèøêîì âûñîêîå
íàïðÿæåíèå â ñåòè,
ïîäàâàåìîå íà èñòî÷íèê
ïèòàíèÿ.
S Ïðîâåðüòå íàïðÿæåíèå â ñåòè. Ïîò ðåáóåòñÿ
îòêëþ÷èòü ïèòàíèå îò ñåòè, ÷òîáû ïåðåâåñòè
ñèñòåìó â èñõîäíîå ñîñòîÿíèå.
Ñâåòîäèîäíûé èíäèêàòîð ãîðèò/ìèãàåò, ïîêà îáíàðóæèâàåòñÿ íåèñïðàâíîñò ü. Èíäèêàòîð
ãàñíåò, òîëüêî êîãäà íåèñïðàâíîñòü óñòðàíÿåòñÿ è àïïàðàò âíîâü âêëþ÷àåòñÿ â ðàáîòó.
3 ÈÍÔÎÐÌÀÖÈß ÄËß ÇÀÊÀÇÀ ÇÀÏÀÑÍÛÕ ×ÀÑÒÅÉ
Ïðèìå÷àíèå:
à àðàíìèéíú²å îáÿçàìåëüñòâà ïîñòàâùèêà òåðÿþò ñèëó, åñëè ïîêóïàòåëú
ñàìîñòîÿòåëúíî ïûòàåòñÿ ïðî èçâåñòè êàêèå-ëèáî ðàáîòû ïî óñòðàíåíèþ
íåèñïðàâíîñòåé èçäåëèÿ â òå÷åíèå ã à ðàíòèéíîã î ñðîêà.
Çàïàñíûå ÷àñòè ìîæíî çàêàçòú ó áëèæàéøåãî ê Âàì ESAB, (ñì. ïåðå÷åíú íà
ïîñëåäíåé ñòðàíèöå äàííîé áðîøþðû).
RU
-- 6 --
bi06d1ea
1 INTRODUCTION
This manual describes operation and use of the A2 control panel, installed in the
AristoArc 400 & AristoArc 500 welding power unit.
For general information on operation, see the power source operating instructions.
1.1 The control panel
1 Yellow indicating lamp -- non--specific fault indica-
tion.
2 Knob for setting the welding current
3 Knob for setting the arc force
1.2 Remote control unit
Using a r emote control unit, the primary parameters of the welding process can be
controlled from a device other than the control panel.
Aristo machines with intergral control panels should have program version 1.21 or
higher, in order for the remote control to function correctly.
When the remote control unit is connected, the power source is in remote control
mode; the buttons and knobs are blocked. The functions can only be adjusted via
the r emote control unit.
1.3 Settings
Settings AristoArc 400 AristoArc 500
Current 16 -- 400 A 16 -- 500 A
Arc force 0--10 0--10
Current
Higher current produces wider and deeper penetration into the workpiece.
Arc force
The arc force controls how the current changes when the arc length changes. A
lower value gives a calmer arc with less spatter.
GB
-- 7 --
bi06d1ea
2 FAULT INDICATION
If the lamp: Cause Action
-- flashes The control panel has lost
contact with the power unit.
S Check the cables. It will be necessary to turn off
the power supply to reset the system.
-- is steadily lit The thermal overload trips
have operated.
S Check to see if the air filter is clogged.
The mains voltage to the
power unit is too high.
S Check the mains voltage. It will be necessary to
turn off the power supply to reset the system.
The LED glows / flashes as long as the fault is detected, and it can only be reset if the fault is repaired
or the machine restarted.
3 ORDERING SPARE PARTS
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
Çàïàñíûå ÷àñòè ìîæíî çàêàçòú ó áëèæàéøåãî ê Âàì ESAB, (ñì. ïåðå÷åíú íà
ïîñëåäíåé ñòðàíèöå äàííîé áðîøþðû).
GB
-- 8 --
page
Diagram Ñõåìà
-- 9 --
bi06e11a
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

ESAB A2 Origo™ Používateľská príručka

Kategória
Zvárací systém
Typ
Používateľská príručka

V iných jazykoch