Sony KF-50SX100K Návod na obsluhu

R

4-078-836-31(1)

Instruction Manual

KF-50SX100K

GB

Návod k obsluze

CZ

Instrukcja obsługi

PL

Kezelési útmutató

HU

Инструкция пo эксплyатации

RU

Инструкции за експлоатация

BG

3

GB

Introduction

Thank you for choosing this Sony “Grand Wega” model.

Before operating the set, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

• Informs you of possible hazards.

• Important information.

• Information on a feature.

• 1,2... Sequence of instructions.

• Shaded buttons on the remote control show the

buttons you have to press to follow the sequence

of instructions.

• Informs you of the result of the instructions.

Safety Information

All TV’s operate on extremely high voltages. To prevent fire or electric shock, please follow the safety guidelines indicated in the

blue sheet supplied.

•

When moving the set two persons are needed. DO NOT push speaker nets placed on the both side of the screen to prevent

these parts from deformation and do not grasp the front panels to prevent these parts from breaking off. Support screen

bottom with one hand while grasping the top part with the other hand.

•Do not block or cover the ventilation opening placed on the left bottom rear side of the set. For ventilation, leave a space of at least

10 cm from the wall.

•After transporting the set directly from a cold to a warm location, or if the room temperature has changed suddenly, pictures may

be blurred or show poor colour over portions of the picture. This is because moisture has condensed on the mirrors or lenses inside

the set. Let the moisture evaporate before using the set.

•To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed

down from the ceiling.

•The screen of this set has an anti-reflection screen coating. To avoid screen degradation, follow the mentioned below:

•To remove dust from the screen surface, wipe with the suplied cleaning cloth or a soft cloth.

•Clean the screen and cabinet with a soft dampened cloth. Do not use any abrasive cleaners. As a safety precaution, unplug the

set before cleaning it.

•Avoid touching the screen, and take care not to scratch the surface with hard objects.

Table of Contents

Introduction ...................................................................................................................................................................................................................... 3

Safety Information............................................................................................................................................................................................................ 3

Overview

Checking the Accessories Supplied.................................................................................................................................................................. 4

Overview of TV Buttons .................................................................................................................................................................................... 4

Overview of Remote Control Buttons.............................................................................................................................................................. 5

Installation

Inserting Batteries into the Remote Control.................................................................................................................................................... 6

Connecting the Aerial and VCR ....................................................................................................................................................................... 6

Stabilizing the set................................................................................................................................................................................................ 6

First Time Operation

Switching on the set and Automatically Tuning............................................................................................................................................ 7

Menu System

Changing the Screen Format............................................................................................................................................................................. 9

Introducing the Menu System........................................................................................................................................................................... 9

On Screen display Menus Guide.................................................................................................................................................................... 10

Using the Menu System:

Adjusting the Picture..................................................................................................................................................................................... 11

Adjusting the Sound...................................................................................................................................................................................... 12

Using the Features menu............................................................................................................................................................................... 14

Manually Tuning the TV............................................................................................................................................................................... 15

Labelling a channel ........................................................................................................................................................................................ 16

Skipping programme positions.................................................................................................................................................................... 17

Using the “Further Programme Preset” function...................................................................................................................................... 18

Inputting your personal ID........................................................................................................................................................................... 19

Using the Demo Mode................................................................................................................................................................................... 20

Adjusting the H Centre picture for an RGB source................................................................................................................................... 21

Labelling and Selecting the screen format of Input Sources.................................................................................................................... 22

Using Multi PIP (Picture In Picture)............................................................................................................................................................ 23

Using PAP (Picture And Picture)................................................................................................................................................................. 23

Teletext...................................................................................................................................................................................................................... 24

NexTView................................................................................................................................................................................................................. 26

Optional Connections

Connecting Optional Equipment.................................................................................................................................................................... 28

Using Optional Equipment.............................................................................................................................................................................. 29

Smartlink............................................................................................................................................................................................................ 30

Remote Control of other Sony Equipment.................................................................................................................................................... 30

Additional Information

Optimum Viewing Area .................................................................................................................................................................................. 31

Replacing the Lamp.......................................................................................................................................................................................... 32

Specifications..................................................................................................................................................................................................... 33

Troubleshooting................................................................................................................................................................................................ 34

MENU

K

4

One Remote Control

(RM-903)

Overview of TV Buttons

(conectores lado izquierdo)

Checking the Accessories Supplied

Overview

Two batteries (R6 type)

Lamp

indicator (see

page 32)

Video Input

jack

Programme up

or down buttons

(selects TV channels)

Selecting

input source

Volume control

buttons

On/Off

Switch

Standby indicator:

• By pressing the

switch off button of

the Remote Control,

standby indicator

lights up in red

colour.

• By pressing the main

switch off on the set,

the standby indicator

lights up in amber

colour.

Headphone

jack

Audio Input

jacks

S Video

Input jack

Press on the mark ,

on the front of the set

to reveal the front

connectors.

Overview

s

1 Wrench2 Brackets

2 Screws

1 Cleaning cloth

5

GB

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

K

VIDEO TV

VT

R 1 2 3 4 DVD

CH

Overview

Overview of Remote Control Buttons

Resetting to factory set levels

Press not only to return picture and sound

settings to factory-set levels, but also to re-

install the set as the first time it was switched

on.

After the "Language/Country" menu

appeared on the screen, proceed in the same

way as described in the section "Switching on

the set and automatically Tuning" of this

instruction manual.

VCR on/off

Press to switch your VCR on or off.

Muting the Sound

Press to mute TV sound.

Press again to restore the sound.

Selecting TV mode

Press to switch off Teletext or video input.

PAP (Picture And Picture)

For more details, please refer to the section

"Using PAP (Picture And Picture)".

Selecting Teletext

Press to switch on Teletext.

Displaying EPG

Press to display the Electronic Programme

Guide (EPG). Press again to switch off EPG.

Freezing the picture

Press to freeze the picture. Press again to

return to the normal picture.

Selecting channels

Press to select channels.

For double-digit programme numbers, e.g.

23, press -/-- first, then the buttons 2 and 3.

If you enter an incorrect first digit, this

should be corrected by entering another digit

(0-9) and then selecting -/-- button again to

enter the programme number of your choice.

Selecting Sound mode

Press repeatedly to change the sound mode.

Selecting Picture mode

Press repeatedly to change the picture mode.

Adjusting TV Volume

Press to adjust the volume of the TV.

Displaying the time

Press to switch the time on or off

(available only when teletext is

broadcast).

VCR operation

For more details, please refer to the

section "Remote Control of other

Sony Equipment".

Besides TV functions, all coloured buttons as well as green

symbols are also used for Teletext operation. For more details,

please refer to the "Teletext" section of this instruction manual.

Overview

To Temporarily Switch Off

Press to temporarily switch off TV (the standby

indicator

on the set lights up in red). Press

again to switch on TV from standby mode.

After 15-30 minutes without a signal and

without any button being pressed, the set

switches automatically into standby mode.

Displaying On Screen Information

Press to display all on-screen indications.

Press again to cancel.

Selecting Input source

Press repeatedly until the desired input symbol of

the source appears on the screen.

Back to the channel last watched

Press to watch the last channel selected (watched for

at least 5 seconds).

Selecting Screen format

Press repeteadly to change the format of the screen

(for more details, please refer to the section

“Changing the Screen format”).

Displaying Multi PIP (Picture In Picture)

Press to display Multi PIP mode. Press again to

cancel.

Joystick for menu selection

• When MENU is switched on:

4 Scroll Up

$ Scroll Down

Z Previous menu or selection

z Next menu or selection

OK Confirms your selection

• When MENU is switched off:

Z Return to the last menu screen.

OK Shows a channel overview

Selecting channels

Press to select the next or previous channel.

Displaying the menu system

Press to display the menu on the screen. Press again

to remove the menu display from the screen.

6

Installation

Make sure you insert the batteries using the correct

polarities.

Always remember to dispose of used batteries in an

environmental friendly way.

Inserting Batteries into the Remote Control

Connecting cables are not supplied.

Connecting the Aerial and VCR

or

VCR

The Scart lead is optional.

If you use this optional connection it can improve picture and sound quality when using a VCR.

If you do not use a SCART lead, after automatically tuning the set refer to the "Manually Tuning the TV" section of this

instruction manual, to tune in the set to the output of your VCR. Also refer to your VCR instruction manual to find out

how to find the output channel of your VCR.

OUT IN

Installation

Stabilizing the set the set

After setting up, secure the set to a wall, etc., with the supplied brackets, for safety purposes.

1 Mount the two supplied brackets with the screws to the upper rear side of the set.

2 Pass a strong cord or a chain through each bracket mounted in 1, and then secure to a wall or a pillar, etc.

Do not block or cover this ventilation opening. For

ventilation, leave a space of at least 10 cm from the wall.

7

GB

First Time Operation

The first time you switch on your TV, a sequence of menu screen appear on the TV enabling you to 1) choose the language

of the menu screen, 2) choose the country in which you wish to operate the set, 3) search and stores all

available channels (TV Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.

However, if you need to change the language menu, change the country, change or repeat the tuning (e.g. when you move

house) or rearrange again the order of the channels afterwards, you can do that by selecting the appropriate menu in

the (Set Up)

.

Switching on the set and Automatically Tuning

1 Connect the set plug to the mains socket (220-240V AC, 50 Hz). Press

the

on/off button on your set to switch on. The first time you press

this button the Language/Country menu displays automatically on

the screen.

2 Push the joystick on the remote control to $ or 4 to select the

language, then press OK to confirm your selection. From now on all

the menus will appear in the selected language.

3 Push the joystick to $ or 4 to select the country in which you will

operate the set, then press OK to confirm your selection.

Select "Off" instead of a country if you do not want your

channels (TV Broadcasts) stored in a given channel sequence

starting from programme position 1.

4 The Auto Tuning menu appears on the screen in the selected

language, then press the OK button on the remote control to select

Yes.

5 A new menu appears automatically on the screen asking you to

check that the aerial is connected. Confirm that the aerial is connected

and then press the OK button to start the automatic tuning.

• The TV starts to automatically search and store all available

channels (TV Broadcast) for you.

• If you have selected “Off” option in the Country menu and

you make a new autotuning afterwards, the TV Broadcasts

will be stored from the selected programme number.

This procedure could take some minutes. Please, be patient and

do not press any button. Otherwise the automatic tuning will

not be completed.

continued...

First Time Operation

Language/Country

Language

Country

Select Language: Confirm: OK

4 Italiano

Français

Español

English

Deutsch

Dansk

Čeština

Language/Country

Language

Country

Select Language: Confir m: OK

4 Italiano

Français

Español

English

Deutsch

Dansk

Čeština

Language/Country

Language

Country

Select Language: Confirm: OK

4 Italiano

Français

Español

English

Deutsch

Dansk

Čeština

Language/Country

Language

Country

Select Country:

Confirm: OK

4

Finland

Denmark

Czech Rep.

Bulgaria

Belgium

Austria

Off

Do you want to start

automatic tuning?

Yes: OK No:

Please confirm that

aerial is connected!

Yes: OK No:

1

2

3

4

5

CO2

CO3

CO4

CO7

CO8

Searching...

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

8

First Time Operation

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

V

I

D

E

TV

O

Programme Sorting

Select Prog: Confirm:

PROG CH LABEL

1

2

3

4

5

6

7

8

9

10

11

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

TV 5

PRO 7

EU-SP

SWF

RTL

SAT

MDR

DDI

DSF

RTL 2

KAB 1

Programme Sorting

Select Position: Move: OK

C03 TV 5

PROG CH LABEL

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

TV 5

PRO 7

EU-SP

SWF

RTL

SAT

MDR

DDI

DSF

RTL 2

KAB 1

1

2

3

4

5

6

7

8

9

10

11

6 After all available channels are captured and stored, the

Programme Sorting menu appears automatically on the screen

enabling you to change the order in which the channels appear

on the screen.

a) If you do not wish to change the channel order, go to step 7.

b) If you wish to change the channel order:

1Push the joystick on the remote control to $ or 4 to select the

programme number with the channel (TV Broadcast) you wish to

rearrange, then push to z.

2 Push the joystick to $ or 4 to select the new programme number

position for your selected channel (TV Broadcast), then press OK.

The selected channel now moves to its new programme

position and the other channels move accordingly.

3Repeat steps b1) and b2) if you wish to change the order of the

other channels.

7 Press the MENU button to exit and return to the normal TV screen.

The set is now ready for use.

First Time Operation

9

GB

1 Press the button on the remote control repeatedly to select one

of the following formats.

Smart: imitation of wide screen effect for 4:3 broadcast.

4:3: conventional 4:3 picture size, full picture information.

14:9: compromise between 4:3 and 16:9 picture size.

Zoom: widescreen format for letterbox movies.

Wide: for 16:9 broadcast.

In Smart, Zoom and 14:9 modes parts of the top and bottom of the

screen are cut off. Press $ or 4 to adjust the position of the image on

screen (eg to read subtitles).

2 Press the OK button to confirm your selection.

First Time Operation - Menu System

This feature allows you to change the size of the TV picture.

Changing the Screen Format

1 Press the MENU button to switch the first level menu on.

2 •To higlight the desired menu or option, push the joystick to

4 or $.

•To enter to the selected menu or option, push to z

•To return to the last menu or option, push to Z.

•To alter settings of your selected option, push to $/4/Z or z.

•To confirm and store your selection, press OK.

3 Press the MENU button to remove the menu from the screen.

Your set uses an on-screen menu system to guide you through the operations. Use the following buttons on the

Remote Control to operate the menu system:

Introducing the Menu system

OK

push to $/4/Z or z

press OK

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

4:3

4:9

Zoom

Wide

Smart

First Time Operation - Menu System

Joystick:

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

10

Picture Adjustment

Select: Enter:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Audio Adjustment

Equaliser Mode

Equaliser

Adjustment

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Mono

Off

Mono

Select: Enter:

0

.

0

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Do you want to start

automatic tuning?

Yes: OK No:

Programme Sorting

Select Prog: Confirm:

PROG CH LABEL

1

2

3

4

5

6

7

8

9

10

11

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

TV 5

PRO 7

EU-SP

SWF

RTL

SAT

MDR

DDI

DSF

RTL 2

KAB 1

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo Start

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Teletext

Top / Bottom / Full

Text Clear

Reveal

Time Page

Page Overview

Select: Enter:

Menu System

On Screen display Menus Guide

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Audio Adjustment

Equaliser Mode

Equaliser

Adjustment

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Mono

Off

Mono

Select: Enter Menu:

0

.

0

Personal

Features

Auto Format

Format Correction

Sleep Timer

Parental Lock

AV2 Output

Normal

On

Off

TV

Select: Enter Menu:

Speaker

Main

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Enter Menu:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Enter Menu:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Enter Menu:

- - - - - - -

Features

Auto Format

Format Correction

Sleep Timer

Parental Lock

AV2 Output

Normal

On

Off

TV

Select: Enter:

Speaker

Main

Refer to the section

"Adjusting the Picture”

Refer to the section

"Adjusting the Sound”

Refer to the section

"Using the features

menu”

Refer to the section

"Switching on the set

and Automatically

Tuning"

Refer to the section

"Switching on the set

and Automatically

Tuning"

Refer to the

section

“NexTView”

Refer to the

section

"Labelling and

selecting the

screen format

of Input

Sources”

Refer to the

section "Teletext"

Menu System

Refer to the section

"Switching on the set

and Automatically

Tuning"

Refer to the sections

"Manually Tuning the

TV", "Labelling a

channel" and "Skipping

programme positions"

Refer to the section

"Using the Further

Programme Preset

function"

Refer to the section

"Adjusting the H centre

picture for an RGB

source"

Refer to the section

"Inputting your

personal ID"

Refer to the section

"Using the Demo

Mode"

11

GB

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to z to enter the Picture Adjustment menu.

3 Push the joystick to $ or 4 to select the item you wish to change,

then push to z.

Refer to the table below to chose the item and for the effect of

each control:

Picture Mode $ Live (for live broadcast programmes)

Personal (for individual settings)

Movie (for films)

4 Game (for computer games)

Contrast Z Less z More

Brightness

* Z Darker z Brighter

Colour* Z Less z More

Sharpness* Z Softer z Sharper

Hue** Z Reddish z Greenish

Reset Resets picture to the factory preset levels.

AI (Artificial 4 Off: Normal

Intelligence) $ On: Automatic optimization of contrast level

according to the TV signal

Noise $ High: High noise reduction.

Reduction Mid: Medium noise reduction.

Low: Low noise reduction.

Auto: Optimum noise reduction automatically

selected.

4 Off: No noise reduction.

Colour Tone $ Warm: Gives a warm tint to the picture.

---Normal: Normal.

4 Cool: Gives a cool tint to the picture.

* Can only be altered if Personal Picture Mode is selected.

** Only avalaible for NTSC colour signal (e.g: USA video tapes).

4 Push the joystick to 4, $, Z or z to alter the selected item, then

press the OK button to store the new adjustment.

5 Repeat steps 3 and 4 to alter the other items.

6 Press the MENU button to exit and return to the normal TV screen.

Changing the Picture Mode Quickly

You can quickly change the Picture Mode without entering the

Picture Control menu screen.

1 Press the button on the remote control repeatedly to directly

access and select your desired picture mode (Live, Personal, Movie,

or Game).

2 Press the OK button to remove the display from the screen.

Menu System

Although the picture is adjusted at the factory, you can modify it to suit your own taste.

Adjusting the Picture

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Picture Adjustment

Select: Enter:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Picture Mode

Live

Personal

Movie

Game

Contrast

AI

On

Off

Picture Mode

Live

Personal

Movie

Game

Colour Tone

Warm

Normal

Cool

Noise Reduction

High

Mid

Low

Auto

Off

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

K

Menu System

12

Menu System

Although the sound is adjusted at the factory, you can modify it to suit your own taste.

Adjusting the Sound

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the Audio Adjustment menu.

3 Push the joystick to $ or 4 to select the item you wish to change,

then push to z.

Refer to the table below to chose the item and for the effect of

each control:

Equaliser Mode $ Personal (for individual settings)

Vocal

Jazz

Rock

Pop

4 Flat (fixed setting, cannot be adjusted)

*Equaliser Push to

z or Z to select the frequency band you

Adjustment want to alter and push to $ or 4 to adjust. Finally,

press the OK button to store the new adjustment.

Balance Z Left z Right

Loudness $ Off: normal

4 On: for music broadcasts

Space $ Off: normal

4 On: acoustic sound effect

Auto Vol. $ Off: volume level changes according to the

Control broadcast signal

4 On: volume level of the channels will stay the same

independent of the broadcast signal (e.g. in

case of advertisement)

Dual Sound • For a stereo broadcast:

$ Mono

4 Stereo

• For a bilingual broadcast:

$ Mono (for mono channel if available)

A (for channel 1)

4 B (for channel 2)

Headphones:

l

Volume Z Less z More

l

Dual Sound • For a stereo broadcast:

$ Mono

4 Stereo

• For a bilingual broadcast:

$ Mono (for mono channel if available)

A (for channel 1)

B (for channel 2)

4 PAP (only when PAP is switched on)

* Can only be permanently stored if Personal Equaliser Mode is selected,

the other modes (Vocal, Jazz, Rock or Pop) store until the next mode

change.

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Audio Adjustment

Equaliser Mode

Equaliser

Adjustment

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Mono

Off

Mono

Select: Enter:

0

.

0

Audio Adjustment

Equaliser Mode

Equaliser

Adjustment

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Mono

Off

Mono

Personal

Vocal

Jazz

Rock

Pop

Flat

Select Mode: Confirm: OK

0

.

0

Equaliser Adjustment

Sel: Adjust: Confirm:OK

(Personal)

+

0

–

120 500 1,5K 5 K 10 K

Balance

.

Loudness

Off

On

Space

Off

On

Auto Vol. Control

Off

On

Dual Sound

Mono

A

B

Volume

Dual Sound

B

A

continued...

13

GB

Menu System

4 Push the joystick to $, 4, Z or z to alter the selected item, then

press the OK button to store the new adjustment.

5 Repeat steps 3 and 4 to alter the other items.

6 Press the MENU button to exit and return to the normal TV screen.

Changing Sound Mode Quickly

You can quickly change Sound mode without entering the Sound

Control menu screen.

1 Press the button on the remote control repeatedly to directly

access and select your desired sound mode (Personal, Vocal, Jazz,

Rock, Pop or Flat).

2 Press the OK button to remove the display from the screen.

Menu System

Equaliser Mode

Personal

Vocal

Jazz

Rock

Pop

Flat

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

14

Menu System

Using the Features menu you can:

a) Select if you want to listen to the sound from the set directly or through an external amplifier.

b) Adjust automatically the size of picture.

c) Select a time period after which the set switches itself into standby mode.

d)

Lock the buttons on the set. In this way, the set only works by using the remote control buttons.

e) Select the source to be output from the Scart connector :2/q2 (SMARTLINK). In this way you can record from this scart

connector while watching another source. If your VCR supports Smartlink, this procedure is not necessary.

Using the Features Menu

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the Features menu.

3 Push the joystick to $ or 4 to select the desired menu item, then

push to z (see the table below for the effect of each menu item).

4 Push to $ or 4 to select the desired setting and press the OK button

to store.

5 Press the MENU button to exit and return to the normal TV screen.

Features Effect / Operation

Speaker $ Main (sound from the set)

4 Centre In (sound from external amplifier)

Auto Format $ Off: Size of picture is not automatically adjusted.

(only for aerial Normal: Size of picture is automatically adjusted

signal) according to the broadcaster information.

4 Full: The set automatically adjusts the picture size

to eliminate any dark areas on the TV picture (as

shown on the section “Changing the Screen

Format)”.

Format Correction

$ Off: 4:3/14:9 is selected.

(only if Auto Format

is set to “Normal”

4 On: Smart mode is selected automatically for

or “Full”)

4:3/14:9 broadcast.

Sleep Timer

4 Off

10 min.

20 min.

...

$ 90 min.

• One minute before the set switches into standby

mode, the time remaining is displayed on the

screen automatically.

• When watching the TV, press the button on

the remote control to display the time remaining.

• To return to normal operation from standby

mode, press the TV button on the remote

control.

Parental lock $ Off (Normal mode)

4 On (The set can only be switched on using the

remote control, the buttons on the TV do not

work)

AV2 Output $ TV (audio/video signal from the aerial)

AV1

(audio/video signal from the Scart

connector :1/ ).

AV2 (audio/video signal from the Scart

connector

:

2/q2 (SMARTLINK).

AV3 (audio/video signal from the Scart

connector

:

3/q3).

4 AV4 (audio/video signal from the connector … 4

placed in the front of the set).

If you have connected a decoder, please remember

to change back the AV2 Output to "TV" for correct

unscrambling.

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Features

Auto Format

Format Correction

Sleep Timer

Parental Lock

AV2 Output

Normal

On

Off

TV

Select: Enter:

Speaker

Main

Speaker

Main

Centre In

10 min

Sleep Timer

Parental Lock

Off

On

AV2 Output

TV

AV1

AV2

AV3

AV4

Auto Format

Off

Normal

Full

Format Correction

Off

On

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

15

GB

1 Press the MENU button on the remote control to display the

menu on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3 Push the joystick to $ or 4 to select Manual Set Up, then push

to z.

4 Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

5 Push the joystick to $ or 4 to select on which programme number

you want to preset a channel (for VCR select programme number

"0"), then push twice to z. The column SYS is highlighted.

6 Push the joystick to $ or 4 to select the system for TV Broadcast

and VCR channel (B/G for western european countries, L for

France, I for Great Britain or D/K for eastern european countries)

or a external input source (EXT), then push to z. The column CH

is highlighted.

7 Push the joystick to $ or 4 to select the channel tuning, "C" for

terrestrial channels (for TV Broadcast or VCR channel), "S" for

cable channels or F for, direct frequency input then push to z.

8 a) If you know the channel number of the TV Broadcast, the VCR

test signal channel or the frequency, press the number buttons

to enter directly the channel number. Then press the OK button

to store.

b) If you do not know the channel number, push the joystyck to $

to select SEARCH and the set starts automatically to search for

the next available TV Broadcast channel or the channel of the

VCR signal. Then press the OK button to store or press $ to

continue searching the desired channel.

c) For external input sources (EXT), push to $ to select the input

source where you have connected your equipment (AV1, AV2,

AV3 or AV4). Then press the OK button to store.

9 Repeat steps 4 to 8 a), b) or c) if you wish to store more channels.

10 Press the MENU button to exit and return to the normal TV screen.

The set is now ready for use.

Menu System

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Programme Preset

Select: Enter:

PROG CHSYSSKIP LABEL

C09

C10

ARD

BBC

B/G

Off

1

2

3

4

5

6

7

8

9

10

11

PROG CHSYS

Off

SKIP LABEL

1

B/G

L

I

D/K

EXT

PROG SYS

Off

SKIP LABEL

1 B/G

CH

C

S

F

- -

PROG SYS

Off

SKIP LABEL

1 B/G

CH

03

SEARCH

C

PROG CHSYS

Off

SKIP LABEL

3 EXT

AV1

AV2

AV3

AV4

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Menu System

Use this function to preset channels (TV Broadcast) or a video input source one by one to the programme order of your choice.

Manually Tuning the TV

16

Menu System

Names for channels (TV Broadcasts) are usually taken automatically from Teletext if available. You can however name a channel or

an input video source using up to five characters (letters or numbers). Using this function, you can easily identify which channel

(TV Broadcasts) or video source you are watching.

Labelling a channel

1Press the MENU button on the remote control to display the

menu on the screen.

2Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3Push the joystick to $ or 4 to select Manual Set Up, then push

to z.

4Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

5Push the joystick to $ or 4 to select the programme number with

the channel you wish to name.

6Push the joystick to z repeatedly until the first element of the

LABEL column is highlighted.

7Push the joystick to $ or 4 to select a letter, number, "+" or a

blank, then push to z to confirm this character. Select the other

four characters in the same way.

8After selecting all the characters, press the OK button.

9Repeat steps 5 to 8 if you wish to label other channels.

10Press the MENU button to exit and return to the normal TV

screen.

When you select a named channel, the name appears for a few seconds

on the screen.

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Programme Preset

Select: Enter:

PROG CHSYSSKIP LABEL

C09

C10

ARD

BBC

B/G

Off

1

2

3

4

5

6

7

8

9

10

11

PROG SYS

Off

SKIP LABEL

1 B/G

CH

C 03

A

17

GB

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3 Push the joystick to $ or 4 to select Manual Set Up, then push

to z.

4 Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

5 Push the joystick to $ or 4 to select the programme position you

want to skip, then push to z to enter the SKIP column.

6 Push the joystick to $ to select On, then press the OK button to

store.

7 Repeat steps 5 and 6 to skip other unused programme positions.

8 Press the MENU button to exit and return to the normal TV screen.

When changing channels (TV Broadcasts) with the PROGR +/- buttons,

the skipped programme positions do not appear. You can, however, still

select them using the number buttons.

Menu System

You can programme this set to skip any unwanted programme numbers when they are selected with the PROGR +/-

buttons. To cancel this function afterwards, proceed in the same way as described below by selecting Off instead of On in step 6.

Skipping Programme positions

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

PROG SYSSKIP LABEL

1 B/G

CH

C 09

ARD

Off

On

Manual Programme Preset

Select: Enter:

PROG CHSYSSKIP LABEL

C09

C10

ARD

BBC

B/G

Off

1

2

3

4

5

6

7

8

9

10

11

18

Menu System

With this feature you can:

a) Individually attenuate the strength of a channel signal in case of a strong local aerial signal (striped picture).

b) Individually adjust the volume level of each channel.

c) Even normally the automatic fine tuning (AFT) is operating, however you can manually fine-tune the TV to obtain a better picture

reception if the picture is distorted.

d) Preset the AV output for the programme positions of channels with scrambled signals (eg from a pay TV decoder). In this way

a connected VCR records the unscrambled signal.

Using the "Further Programme Preset" function

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3 Push the joystick to $ or 4 to select Manual Set Up then push to z

to enter.

4 Push the joystick to $ or 4 to select Further Programme Preset,

then push to z.

5 Push the joystick to $ or 4 to select the relevant programme

number, then push to z repeatedly to select:

a) ATT (RF attenuator)

b) VOL (Volume Offset)

c) AFT (Automatic Fine Tuning) or

d) DECODER

The selected item changes colour.

6 a) ATT

Push the joystick to $ to select On, then press the OK button.

Repeat steps 5 and 6 a) to attenuate other channels.

b) VOL

Push the joystick to $ or 4 to adjust the volume level of the channel

over a range of -7 to +7, then press the OK button. Repeat steps 5

and 6b) to adjust the volume level of the other channels.

c) AFT

Push the joystick to $ or 4 to fine tune the channel frequency over

a range of -15 to +15, then press the OK button. Repeat steps 5 and

6c) if you wish to fine tune other channels.

d) DECODER

Push the joystick to $ or 4 to select AV1 (for a decoder connected

to the Scart :1/ ) or AV2 (for a decoder connected to the Scart

:2/q 2 (SMARTLINK)), then press the OK button.

Repeat steps 5 and 6d) to select the AV1 or AV2 output for other

programme positions.

The picture from the decoder connected to the Scart connector

:1/ or :2/q 2 (SMARTLINK) on the back of the

set will appear on this programme number.

7 Press the MENU button to exit and return to the normal TV screen.

The set is now ready for use.

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Further Programme Preset

Select: Enter:

PROG AFTVOLATT DECODER

On

Off

0

Off

1

2

3

4

5

6

7

8

9

10

11

PROG AFTVOLATT DECODER

1

Off

On

PROG AFTVOLATT DECODER

1 On -5

2

PROG AFTVOLATT DECODER

1 On -5 2

Off

AV1

AV2

PROG AFTVOLATT DECODER

1On

- 5

19

GB

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3 Push the joystick to $ or 4 to select Manual Set Up, then push to z.

4 Push to $ or 4 to select Personal ID, then push to z.

5 Push the joystick to $ or 4 to select a letter, number, + or a blank;

then push to z to confirm this character. Select the other ten

characters in the same way.

6 After selecting all the characters, press the OK button. A new menu

appears automatically on the screen asking you to be sure that you

want to save this ID.

7 a) If you do not wish to store this ID, push the joystick to Z and

repeat steps 4 to 6 to enter a new ID.

b) If you wish to store this ID, press the OK button.

Remember that this code can only be input once.

8 Press the MENU button to return to the normal TV screen.

When you enter the Manual Set Up menu, in the "Personal ID" option the

code you entered above will be displayed. You will not be able to select and

change this option.

Menu System

You can programme this set with a personal code, using up to eleven characters (letters and numbers). Then using

this fuction it will be possible to identify your set if it was ever stolen.

This code can only be input once!

Make sure to write it down in this instruction manual.

Inputting Your Personal ID

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

Manual Set Up

Select A-Z, 0-9: Store: OK

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

A----------

Are you sure?

Save: OK Cancel:

20

Menu System

This function provides an overview of some of the features available on this set.

Using the Demo Mode

Menu System

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

3 Push the joystick to $ or 4 to select Manual Set Up, then push to z.

4 Push to $ or 4 to select Demo, then push to z to enter and start

the demonstration.

The set starts the demonstration and shows most of the

available picture functions.

Note:

Press the button on the remote control to stop the Demo mode

and return to the normal TV screen.

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo Start

- - - - - - -

21

GB

1 Press the … button repeatedly on the remote control until the

symbol …1 appears on the screen.

2 Push the MENU button to display the menu on the screen.

3 Push the joystick to $ to select the symbol, then push to z to

enter the Set Up menu.

4 Push to $ or 4 to select Manual Set Up then push to z to enter.

5 Push the joystick to $ or 4 to select RGB Set Up then push to z.

6 Push the joystick to z to enter H Centre, then push to $ or 4 to

adjust the centre of the picture over a range of -10 to +10. Press

the OK button to store.

7 Press the MENU button to exit and return to the normal TV screen.

Menu System

S

RM

903

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

TV

V

I

D

E

O

Menu System

When connecting an RGB source, such as a DVD player, to the Scart connector :1/ you may need to readjust the H Centre

of the picture.

Adjusting the H Centre picture for an RGB source

Picture Adjustment

Select: Enter Menu:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Colour Tone

Personal

On

Off

Normal

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

Start Auto Tuning

Start

- - - - - - -

Enter:

Set Up

Auto Tuning

Programme Sorting

Select NexTView

AV Preset

Manual Set Up

Select:

- - - - - - -

Manual Set Up

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Personal ID

Demo

- - - - - - -

RGB Set Up

Adjust Position: Confirm: OK

H Centre

O

… 1

Stránka sa načítava...

Sony KF-50SX100K Návod na obsluhu

Sony KF-50SX100K Návod na obsluhu

v iných jazykoch

Súvisiace články

Ostatné dokumenty