Stránka sa načítava...
Not for
Reproduction
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80019640 Rev A
020619-00 &
020671-00
(BPW1800PX)
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
en - English
ar -
da - Dansk
es - Español
fi - Suomi
fr - Français
hu - Magyar
nl - Nederlands
no - Norsk
pl - Polski
ru -
sv - Svenska
sw - Kiswahili
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
A
B
C
2
A
B
B
A
1
A
B
C
4
A
5
6
A
B
7
B
A
0˚ 15˚40˚
A B
C
D
F
G
H
12
B
A
C
8
9
10
B
D
C
A
11
A
B
Not for
Reproduction
3
3
H
L
K
G
J
D
A
B
C
F
E
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Safety and Control Symbols ................... 4
Equipment Description........................ 4
Assembly................................... 5
Features and Controls ........................ 5
Operation................................... 5
Maintenance ................................ 7
Storage .................................... 7
Troubleshooting ............................. 8
Specifications ............................... 8
Warranty ..................................10
A safety symbol may be used to represent the type
of hazard. WARNING indicates a hazard which, if not
avoided, could result in death or serious injury. NOTICE
address practices not related to personal injury.
This machine is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless supervised
and given instruction concerning safe operation
and understanding of hazards involved.
WARNING
• This machine has been designed for use with
the cleaning agent supplied or recommended
by the manufacturer. The use of other cleaning
agents or chemicals may adversely affect the
safety of the machine.
• High pressure jets can be dangerous if subject to
misuse. The jet must not be directed at persons,
live electrical equipment or the machine itself.
• Do not use the machine within range of
persons unless they wear protective clothing.
• Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
• Risk of explosion – Do not spray flammable liquids.
• High pressure cleaners shall not be used by
children or untrained personnel.
• High pressure hoses, fittings and couplings
are important for the safety of the machine.
Use only hoses, fittings and couplings
recommended by the manufacturer.
• To ensure machine safety, use only original
spare parts from the manufacturer or approved
by the manufacturer
• Water that has flown through backflow
preventers is considered to be non-potable.
• Remove plug from outlet to disconnect power during
cleaning or maintenance and when replacing parts
• Do not use the machine if the cord or important
parts of the machine are damaged, e.g. safety
devices, high pressure hoses, trigger gun.
• Do not use an extension cord with this electric
pressure washer.
• Always switch off the master switch when
leaving the machine unattended.
This electric pressure washer operates at a maximum of 12.0 MPa
(120 BAR or 1,740 PSI (pounds square inch)) at a flow rate of up
to 15.0 LPM (liters per minute)(4.0 GPM (gallons per minute)).
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use, ask
dealer or contact qualified service center. NEVER operate units
with broken or missing parts, or without protective housing or
covers. DO NOT by-pass any safety device on this machine.
DO NOT modify pressure washer in any way. This equipment
is designed to be used with Briggs & Stratton authorized parts
ONLY.
POWERflow+ Technology™
Briggs & Stratton’s POWERflow+ Technology is a system
of components working in concert to deliver high-flow
capability. The force behind POWERflow+ is in the pump
with two separate cleaning modes: high pressure and high
flow that enhances cleaning by providing extended reach,
power soaping, and faster rinsing capabilities.
Chemical Burn
Electrical Shock
Safety Alert Fall Flying Objects
Fluid Injection
Fire
Off
On
Never spray yourself, others, animals, power
sources, or the unit itself.
Read Manual
Non-Potable Water
Not for
Reproduction
5
This pressure washer is provided with a portable residual current
device (PRCD) built into the plug of the power supply cord. This
device provides additional protection from the risk of electric
shock. The PRCD provides 10 mA of protection.
A sensor will shut off the motor when the spray gun trigger
releases or locks. If the motor continues to run while the spray
gun trigger is released or locked, DO NOT USE THE MACHINE.
Contact a Briggs & Stratton authorized service dealer.
NOTICE ON/OFF switch should always be in the OFF
position (0) when pressure washer is not in use.
An overload protection device automatically shuts off the
motor if it overheats or draws excessive current. If the
device trips, disconnect power by pressing master ON/OFF
switch to OFF (0) position. Let unit cool for 30 minutes and
press ON/OFF switch to ON (I) position.
EU Disposal
This symbol indicates the owner of batteries and
electrical or electronic equipment shall not dispose
of this product with unsorted municipal waste. This
product should be disposed of in environmentally
appropriate waste locations. Please contact Briggs & Stratton
or your local retailer for additional disposal information.
Assembly
Figure
1
2
1. Slide supports (1,A) into slots. Align and attach with
screws (1,B). Maintain alignment while tightening.
2. Place handle (2,A) onto supports and align holes.
3. Insert carriage bolts (2,B) through holes from inside of
unit, attach with plastic knobs (2,C), and tighten.
Figure
3
Figure
3
4
6
NOTICE Use ONLY cold water (less than 38°C (100°F)).
1. Screw high pressure hose (3,F) into gun (3,A).
2. Attach blue high pressure hose (3,F) to outlet (3,K)
and tighten.
3. Confirm water inlet screen and black rubber washer is
installed in water inlet coupling (4,A).
4. Attach water inlet coupling to inlet (4,B) and tighten.
NOTICE For best performance, connect ONLY to water
source capable of supplying greater than 18.9 LPM
(5.0 GPM) and 0.17-0.52 MPa (1.7-5.2 BAR or 25-75 PSI)
at electric pressure washer end of garden hose.
5. Run water through garden hose to clean out debris.
NOTICE Using a backflow preventer at pump inlet could
cause pump damage. There MUST be at least 3 m. (10 ft.)
of unrestricted garden hose between pressure washer inlet
and backflow preventer.
WARNING! Water that has flowed through a
backflow preventer is considered to be non-potable.
6. Connect garden hose (4,C) (not to exceed 15 m (50 ft.))
to water inlet (4,B) and tighten.
7. Turn ON water, point gun in a safe direction, press trigger
lock button (5,A), then squeeze trigger to purge system of air.
8. Attach nozzle extension (3,L) to spray gun (3,A). Tighten
by hand.
9. Pull back on collar of nozzle extension (7,A), insert
7-in-1 nozzle (7,B) and release collar. Tug on nozzle to
make sure it is securely in place. See 7-in-1 Nozzle.
Figure
3
8
9
WARNING! Spray could splash back or propel objects
resulting in serious injury. Always wear indirect vented
(chemical splash) safety goggles marked to comply with
ANSI Z87.1 when using or in vicinity of this equipment.
1. Press master ON/OFF switch (3,E) to OFF (0) position.
WARNING! Risk of electrocution. Use of an extension
cord could cause electric shock or burn resulting in
death or serious injury. DO NOT use an extension cord
with this electric pressure washer. Your home’s electrical circuit
receptacle or extension cord may not provide lifesaving portable
residual current device (PRCD) protection.
2. Plug electrical power cord (3,G) into a dedicated
electrical circuit (9) rated for 220-240 volts AC at
10 Amps that is properly insalled in accordance with
all local codes and ordinances. Circuit is not to supply
any other electrical needs.
3. Press RESET button (8,C). Indicator light (8,B) should
be ON.
NOTICE Indicator light must be ON for the electric pressure
washer to operate.
4. Press TEST button (8,A). Indicator light (8,B) should
be OFF.
5. Press RESET button (8,C). Indicator light (8,B) should
be ON.
WARNING! Risk of electrocution. Non-operating
PRCD could result in death or bodily injury. If
indicator light does not stay ON after test and
reset, do not use PRCD.
6. Press master ON/OFF switch to ON (I) position.
7. Point gun in a safe direction, press trigger lock button
and squeeze trigger.
The motor will start and stop as spray gun trigger is
depressed and released.
A Spray Gun G Electric Cord w/ PRCD
B 7-in1 Nozzle H Identification Label
C Accessory Tray J Water Supply Inlet
D Detergent Tank K High Pressure Outlet
E Master ON/OFF Switch L Nozzle Extension
F High Pressure Hose
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Figure
12
The 7-in-1 nozzle allows you to switch between seven
different spray pattern nozzles. Release trigger on spray
gun to engage safety lock before changing spray patterns.
1. Select desired spray pattern:
• Select Maximum 0° nozzle (A) for stubborn cleaning
tasks such as paint removal, oil stains, rust removal or
other stubborn substances (tar, gum, grease, wax, etc.).
• Select General 15° nozzle (B) for tougher cleaning
tasks. Ideal for removing grease and dirt from hard
surfaces. Also capable of stripping paint when held
at a 45° angle.
• Select Gentle 40° nozzle (C) for gentle cleaning
of cars/trucks, boats, RV’s, patio furniture, lawn
equipment, etc.
• Select Fan Spray nozzle (D) for optimal high flow
rinsing away of light dirt and debris.
• Select Fan Spray with Soap nozzle (F) for delicate
surface cleaning of cars, trucks, childrens play
equipment, patio furniture, etc.
• Select Extended Reach nozzle (G) for quick high
flow clean up and long reach cleaning of second
story siding and windows.
• Select Extended Reach with Soap Nozzle (H) to
propell soap to second story siding and windows.
2. Turn dial until desired spray pattern aligns with arrow
on 7-in-1 nozzle.
Usage Tips
• For most effective cleaning, keep nozzle from
20 to 61 cm (8 to 24 in.) away from cleaning surface.
• If nozzle gets too close, especially using a high pressure
nozzle, you may damage surface being cleaned.
• DO NOT get closer than 15 cm (6 in.) when cleaning tires.
Figure
3
WARNING! Chemicals could cause burns resulting
in death or serious injury. DO NOT use caustic liquid
with pressure washer. Use ONLY pressure washer
safe detergents/soaps. Follow manufacturers instructions.
1. Remove cap from detergent tank (D) and fill with
detergent solution. Replace cap.
2. Make sure one of the soap spray pattern nozzles is
selected on 7-in-1 nozzle.
NOTICE Detergent cannot be applied with high pressure
nozzles (maximum, general, delicate, fan spray or
extended reach).
3. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
4. Allow detergent to “soak in” per detergent
manufacturer’s instructions before washing and rinsing.
Pressure Washer Rinsing
1. Select desired high pressure nozzle.
WARNING! Kickback from spray gun could cause
you to fall resulting in death or serious injury.
Operate pressure washer from a stable surface.
Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
2. Apply high pressure spray to a small area and check surface
for damage. If no damage is found, continue rinsing.
3. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Figure
3
1. Release spray gun trigger.
2. Press master ON/OFF switch (E) to OFF (0) position.
NOTICE Releasing the trigger will shut off the motor but
does not shut off electrical power to the unit.
3. Turn off water supply.
4. ALWAYS point spray gun in a safe direction, press
trigger lock button, and squeeze trigger to relieve built
up pressure in the unit.
WARNING! The high pressure stream of water
that this equipment produces could cut through
skin and its underlying tissues, resulting in serious
injury and possible amputation. Keep high pressure hose
connected to pump and spray gun while system is
pressurized. DO NOT allow CHILDREN to play with or
operate pressure washer. ALWAYS point spray gun in safe
direction, squeeze spray gun trigger to release high
pressure, every time you turn off pressure washer.
5. Disconnect PRCD plug (G) from outlet and coil power
cord on bottom hook of accessory tray.
6. Wrap high pressure hose on top hook of accessory tray.
7. Store high pressure nozzle on end of nozzle
extension. Store spray gun, nozzle extension, and
7-in-1 nozzle on the accessory tray.
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and “freeze”
pump action. Follow these procedures after every use:
1. Run pressure washer with soap nozzle until tank is empty.
2. Add 0.5 liter (0.5 quart) of water to detergent tank, and
run with soap spray nozzle. Flush one to two minutes.
3. Press master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
4. Turn off water supply. Point gun in a safe direction,
press trigger lock button, and squeeze trigger to
relieve trapped pressure.
Not for
Reproduction
7
5. Disconnect garden hose from water inlet. Disconnect
high pressure hose from gun and high pressure outlet.
6. Drain water from hose and spray gun, and wipe off
exterior surfaces.
7. Drain water from pump by tipping unit onto its right
side (water inlet facing down) for two minutes. Flip
unit over and let rest on high pressure outlet for an
additional two minutes.
8. Wrap high pressure hose on top hook of accessory tray.
9. Coil power cord on bottom hook of accessory tray.
Store spray gun, nozzle extension and 7-in-1 nozzle
on accessory tray.
10. Store unit in a clean, dry area.
11. If storing for more than 30 days, see Storage.
Regular electric maintenance will improve performance
and extend the life of the pressure washer. See any
Briggs & Stratton Authorized Service Dealer for service.
DO NOT allow children to clean or maintain without supervision.
The electric pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from warranty, operator
must maintain pressure washer as instructed in this
manual, including proper storage as detailed in Storage.
WARNING! To ensure machine safety, use only
original spare parts from the manufacturer or approved
by the manufacturer. Should you have questions about
replacing components on your pressure washer, please visit our
website at BRIGGSandSTRATTON.COM. If cord is damaged,
see an Briggs & Stratton Authorized Service Dealer.
Clean nozzle to correct excessive pump pressure caused
by a clogged spray nozzle:
1. Press master ON/OFF switch to OFF (0) position.
Remove power cord plug from electrical outlet.
2. Remove 7-in-1 nozzle from end of nozzle extension.
3. Use a small paper clip to free foreign material clogging
or restricting nozzle.
4. Reinstall 7-in-1 nozzle into nozzle extension.
Figure
10
The use of lubricant (petroleum or synthetic grease) helps seat
o-rings providing an improved seal. Apply lubricant to o-rings
prior to assembling high pressure hose (A), garden hose to
the pump (B), spray gun (C), and nozzle extension (D).
Purchase an O-Ring Maintenance Kit by contacting a Briggs
& Stratton Authorized Service Dealer. NEVER repair leaking
connections with sealant of any kind. Replace o-ring or seal.
Figure
11
WARNING! To reduce the risk of fire, replace only with
13-amp BS 1362 rated fuse.
If equipped with fuse within PRCD:
1. Locate fuse on pin side of PRCD plug.
2. Using a flat-head screwdriver, remove cover (A) and
fuse. Remove fuse (B) from cover. Replace fuse with
13-amp BS 1362 rated fuse.
3. Insert cover and fuse.
Follow steps 1-10 in After Each Use.
NOTICE Water left in pump could freeze and permanently
damage pump. Freeze damage is not covered under warranty.
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver to prevent freeze
damage, and lubricate pistons and seals.
NOTICE Failure to protect unit from freezing termperatures
will damage pump and render unit inoperable. Freeze
damage is not covered under warranty.
1. Wrap high pressure hose on top hook of accessory tray.
2. Coil power cord on bottom hook of accessory tray.
3. Store spray gun, nozzle extension and 7-in-1 nozzle
on accessory tray.
4. Cover unit with a protective cover that does not retain
moisture and store in a clean, dry area protected from
freezing temperatures.
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Problem Cause
Pump has following
1. Water inlet is blocked.
2. Inadequate water supply.
3. Garden hose is kinked or leaking.
4. Clogged water inlet screen.
5. Spray nozzle is obstructed.
1. Clear inlet.
2. Provide adequate water flow.
3. Straighten garden hose or replace if leaking.
4. Clean or replace water inlet screen.
5. Clean spray nozzle.
1. Water supply is not turned on.
2. Unit is not turned on.
3. Garden hose is too long.
4. Fuse blown or circuit breaker tripped.
1. Turn on water supply.
2. Press master ON/OFF switch to ON (I)
position. Reset PRCD.
3. Use only 15.24 m (50 ft.) maximum
garden hose.
4. a.) Replace fuse or reset circuit breaker.
b.) Disconnect other electrical
appliances and turn off lights in the
circuit or operate on dedicated circuit.
c.) Run POWERflow+ High Flow Mode
(
) nozzle setting for 5 minutes.
spray.
1. High pressure nozzle is installed.
2. Inlet water supply pressure too high.
1. Install nozzle spray tip.
2. Slowly close water supply valve until
chemical starts to draw.
1. Garden hose loose to water inlet.
2. Loose high pressure hose connections.
3. Damaged o-ring.
1. Hand tighten garden hose.
2. Remove hose and reinstall.
3. Replace o-ring.
Allowable Pressure MPa/BAR/PSI 16.0/160/2,320
*
Max Flow LPM/GPM 15.0/4.0
*
Rated Pressure and Flow MPa/BAR/PSI @ LPM/GPM 12.0/120/1,740 @ 5.5/1.45
*
Max Water Supply Temperature °C/°F 38/100
Rated Voltage V 220 - 240
Rated Frequency Hz 50/60
Power Consumption W 2,500
Current A 9.0
Protection Class Class Class II
Protection Degree IP xx IPX5
Hand - Arm Vibration a
hd
Uncertainty K
m/s
2
m/s
2
*
0.2
*
Sound Pressure Level L
pA
Uncertainty K
pA
dB(A)
dB(A)
74
*
2
*
Measured Sound Power Level L
WA
dB(A) 94
*
Guaranteed Sound Power Level L
WAd
dB(A) 96
*
*
Per EN 60335-2-79: 2012.
Not for
Reproduction
9
Lavorwash spa
Via J.F.Kennedy, 12 – 46020 Pegognaga (MN) – Italy
This Declaration of Conformity is issued under the sole responsibility of the manufacturer. This is to certify that the
products listed in this document are in conformity with the relevant Union harmonization legislation and can carry the CE
mark. These models comply with the following Directives and related Standards.
High Pressure Cleaner
BPW1800PX
2006/42/EC (+2009/127/EC) EN 60335-1:2012
2006/95/EC EN 60335-2-79:2012
2004/108/EC EN 62233:2008
2000/14/EC (+2005/88/EC) EN 55014-1:2006+A1:2009+A2:2011
2011/65/EU (+2015/863/EU) EN 55014-2:1997+A1:2001+A2:2008
EN 50581:2012
Sound Power Level
Measured dB(A): 94
Guaranteed dB(A): 96
2000/14/EC: The appliance is defined by No. 27 of Annex I. Conformity evaluation procedure in accordance with Annex V.
The technical file is stored in Lavorwash spa, via J.F.Kennedy, 12 - 46020 Pegognaga (MN) – Italy.
Lavorwash S.p.A
via J.F.Kennedy, 12
46020 Pegognaga Giancarlo Lanfredi
(MN) - Italy Pegognaga, October 15, 2015 General Manager
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
80011059_EN Rev -
BRIGGS & STRATTON PRODUCTS WARRANTY POLICY January 2014
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for
and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
.
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
To ensure prompt and complete warranty coverage, register your product at the website shown above or at www.onlineproductregistration.com, or mail the complete
registration card (if provided), or call 1-800-743-4115 (in USA).
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for
warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse,
improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
12 months None
Not for
Reproduction
11
Not for
Reproduction
5 BRIGGSandSTRATTON.COM
1
.Briggs & Stratton
OFF
)0(
ON/OFF
OnLOFF
30
.OFF (0)
.ON (I)
2
1
(A
,
1)
.1
(B
,
1)
(A
,
2)
.2
(B
,
2)
.3
(C
,
2)
3
6
4
3
.((100) 38° )
.(A,3) (F,3)
.1
(K
,
3)
(F
,
3)
.2
.3
.
(A
,
4)
(B
,
4)
.4
5
(
psi (1.72-5.17 25-75
(l 18
.
9
.5
(
10)
3
.
15
)(C
,
4)
.6
(B
,
4)
50)
,
(A
,
5)
.7
(A
,
3)
(L
,
3)
.8
(B
,
7) 1
7
(A
,
7)
.9
.1
7 ةهوفلا
9.
3.
ANSI
. Z87.1
.
OFF (0)
(E
,
3)
ON/OFF
.1
220-240
(G
,
3)
.2
10
(B
,
8)
RESET (8
,
A)
.3
(B
,
8)
TEST (8
,
A)
.4
(B
,
8)
RESET (8
,
A)
.5
PRCD
.PRCD
.
ON (I)
(D
,
3)
ON/OFF
.6
.7
12
1
7
-7
1
7
.1
(A)
0
•
)
.
(
(B)
15
•
45
(C)
40
•
(D)
•
(F)
•
(G)
•
(H)
•
.1
7
.2
•
(
24
8)
61
20
•
(
6)
15
•
Not for
Reproduction
4
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. . . . . . . . . . . . . . . . . . . . . . . . . . .
4. . . . . . . . . . . . . . . . . . . . . . . . .
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. . . . . . . . . . . . . . . . . . . . . . . . . .
8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
)
(
.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
12.0
(
1
,
740
120)
(
4.0)
15.00
.
Briggs & Stratton
POWERflow+™
Briggs & Stratton
POWERflow+
POERFlow+
.
D
10
PRCD
A
G
B1
7
H
C
J
D
K
EPRCD /
L
F
Not for
Reproduction
7 BRIGGSandSTRATTON.COM
Briggs & Stratton
.BRIGGSandSTRATTON.COM
.Briggs & Stratton
. OFF (0)
(D)
ON/OFF
.1
.
.2
. .3
.
17 4
10
(
)
Ao
DCB
.Briggs & Stratton
.
11
A
B
BS 1362.
.
1-10
.
.1
.
.2
.
1
7
.3
.4
.
Not for
Reproduction
6
3
(D)
.1
.1
7
.2
.3
.4
.1
.2
.3
3
.1
. OFF (0)
(E)
ON/OFF
.2
.3
.4
PRCD (G)
.5
.6
.7
1
7
.1
0-5
.2
. OFF (0)
(D)
ON/OFF
.3
.6 .
.4
.
.5
.
.
.6
)
.7
(
.8
.9
1
7
.10
.
30
.11
Not for
Reproduction
9 BRIGGSandSTRATTON.COM
.1
.2
.3
.4
.5
.
.1
.
.2
.
.3
.
.4
.5
.1
.2
.3
.4
.1
(D,3)
ON/OFF
.2
.PRCD
.(ON (I
.3
.(
50)
15.24
.4
(
5
(
1
2
.1
.2
.1
.2
.3
.1
2
.3
.
MPa/BAR/PSI
*
16.0/160/2,320
*
15.0/4.0
MPa/BAR/PSI @ LPM/GPM12/120/1,740 @ 5.5/1.45
C/°F°38/100
V220 - 240
50/60
2,500
A9.0
IP xxIPX5
a
hd
K
m/s
2
m/s
2
*
0.2
*
L
pA
K
pA
(A)
(A)
*
74
*
2
L
WA
(A)
*
94
L
WAd
(A)
*
96
EN 60335-2-79:2012
*
Not for
Reproduction
8
Lavorwash spa
Via J.F.Kennedy, 12 – 46020 Pegognaga (MN) – Italy
2006/42/EC (+2009/127/EC) EN 60335-1:2012
2006/95/EC EN 60335-2-79:2012
2004/108/EC EN 62233:2008
2000/14/EC (+2005/88/EC) EN 55014-1:2006+A1:2009+A2:2011
2011/65/EU (+2015/863/EU) EN 55014-2:1997+A1:2001+A2:2008
EN 50581:2012
94
96
.F.Kennedy, 12 - 46020 Pegognaga (MN) – Italy.
Lavorwash S.p.A
46020 Pegognaga Giancarlo Lanfredi
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
EN_80011059
2014 BRIGGS & STRATTON
Briggs & Stratton
.BRIGGSandSTRATTON.COM
.
**.
**
Briggs & Stratton Australia Pty
1300 274 447
BRIGGSandSTRATTON.COM
.Ltd, 1 Moorebank Avenue, NSW, Australia, 2170
1-800-743-4115
(
)
www.onlineproductregistration.com
.
(
)
.Briggs & Stratton
Briggs & Stratton
Briggs & Stratton
(
)
(
E15 E85
)
12
Not for
Reproduction
4 BRIGGSandSTRATTON.COM4 BRIGGSandSTRATTON.COM
....................... 4
.....................................4
...........................4
................ 4
...................................5
.......................... 7
.....................................7
................... 8
................................... 8
......................................10
може
ВАЖНО
•
•
•
•
•
•
•
•
•
•
•
•
•
ВАЖНО
Not for
Reproduction
5 5
ВАЖНО
1
2
1,A
1,B
2,A
2,B
2,C
3
3
4
6
ВАЖНО
3,F3,A).
3,F
3,K
4,A).
4,B
ВАЖНО
ВАЖНО
4,C
4,B
(5,A
3,L
3,A
7,A),
7,B
Дюза 7-в-1.
3
9
3,E
3,G
8,C
8,B
ВАЖНО
8,A
(8,B
8,C
8,B
A G
B H
C J
D
K
E
PRCD
L
F
/