Parkside PGG 15 C2 Translation Of The Original Instructions

Kategória
Elektrické náradie
Typ
Translation Of The Original Instructions
POWER ENGRAVING TOOL PGG 15 C2
IAN 275634
GRAVIERGERÄT
Originalbetriebsanleitung
POWER ENGRAVING TOOL
Translation of the original instructions
APARAT ZA GRAVIRANJE
Prevod originalnega navodila za uporabo
GRAVÍROZÓ KÉSZÜLÉK
Az originál használati utasítás fordítása
GRAVÍROVACÍ PŘÍSTROJ
Překlad originálního provozního návodu
GRAVÍROVAČKA
Preklad originálneho návodu na obsluhu
GB Translation of the original instructions Page 1
HU Az originál használati utasítás fordítása Oldal 17
SI Prevod originalnega navodila za uporabo Stran 33
CZ Překlad originálního provozního návodu Strana 51
SK Preklad originálneho návodu na obsluhu Strana 67
DE / AT / CH Originalbetriebsanleitung Seite 83
Before reading, unfold the page containing the illustrations and familiarise
yourself with all functions of the device.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg
a készülék mindegyik funkcióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami
naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi
funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všet-
kými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen
Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
PGG 15 C2
GB
 1
Contents
Introduction .................................. 2
Intended use ..........................................2
Features .............................................3
Package contents ......................................3
Technical data ........................................3
General power tool safety warnings ............. 5
1. Work area safety ....................................6
2. Electrical safety .....................................6
3. Personal safety ......................................7
4. Power tool use and care ..............................8
5. Service ............................................9
Operation ................................... 9
Switching on and off ...................................9
Setting the stroke depth .................................9
Changing the engraving tips ............................10
Working procedures ...................................11
Cleaning ....................................12
Disposal ....................................12
Disposal of the appliance ...............................12
Warranty ...................................13
Service .....................................14
Importer ....................................14
Translation of the original Conformity Declaration . 15
PGG 15 C2
2 
GB
POWER ENGRAVING TOOL PGG 15 C2
Introduction
Congratulations on the purchase of your new appliance. You have
selected a high-quality product. The operating instructions are part
of this product. They contain important information on safety, usage
and disposal. Before using the product, familiarise yourself with all
handling and safety guidelines. Use the product only as described
and for the range of applications specified. Please also pass these
operating instructions on to any future owner.
Intended use
This appliance is intended for engraving or decorating materials
such as metal, plastic, glass, leather and stone. Any other usage
of or modification to the appliance is deemed to be improper and
carries a significant risk of accidents. The manufacturer accepts no
responsibility for damage(s) attributable to misuse. This appliance is
not intended for commercial use.
PGG 15 C2
GB
 3
Features
ON/OFF switch
Stroke rate control
Carrying lug
Power cable
Engraving tip
Engraving tip lock
Engraving templates
Package contents
1 power engraving tool PGG 15 C2
4 engraving templates
1 set of operating instructions
Technical data
Rated voltage: 230V
~
50Hz (alternating current)
Operating mode: periodic intermittent operation: S3 20%
Note: A duty cycle (in %) explicitly specifies the maximum continu-
ous use and the subsequent rest period. In this case, for instance,
the tool needs a cooling period of eight minutes after two minutes of
operation.
Rated current: 0.15 A
Stroke rate: 6000 rpm
Approximate weight: 370 g
PGG 15 C2
4 
GB
Noise emission value:
Noise measurement value determined in accordance with EN 60745.
The A-rated noise level of the power tool is typically as follows:
Sound pressure level: L
pA
= 74.4 dB(A)
Uncertainty: K
pA
= 3 dB
Sound power level: L
WA
= 85.4 dB(A)
Uncertainty: K
WA
= 3 dB
Wear hearing protection!
Total vibration value:
a
h
= 1.582 m/s
2
Uncertainty K = 1.5 m/s
2
NOTE
The vibration level specified in these instructions has been
measured in accordance with the standardised measuring
procedure specified in EN 60745 and can be used to make
equipment comparisons. The specified vibration emission
value can also be used to make an initial exposure estimate.
PGG 15 C2
GB
 5
WARNING!
The vibration level varies in accordance with the use of the
power tool and may be higher than the value specified in
these instructions in some cases. Regular use of the electric
tool in such a way may cause the user to underestimate the
vibration. Try to keep the vibration loads as low as possible.
Measures to reduce the vibration load include wearing
gloves and limiting your working time. Wherein all states of
operation must be included (e.g. times when the power tool
is switched off and times where the power tool is switched
on but running without load).
General power tool
safety warnings
WARNING!
Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded/mains adapter) power tools or battery-operated (cordless)
power tool.
PGG 15 C2
6 
GB
1. Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock.
PGG 15 C2
GB
 7
3. Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye protec-
tion. Protective equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards.
PGG 15 C2
8 
GB
4. Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments, chang-
ing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instruc-
tions to operate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control.
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working condi-
tions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazard-
ous situation.
PGG 15 C2
GB
 9
5. Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
Operation
Never use the appliance for other purposes and only original parts/
accessories. Using attachments or accessory tools other than those
recommended in the operating instructions can lead to a risk of injury.
Switching on and off
Insert the power plug into a mains wall socket.
Switching on:
Press the ON/OFF switch
.
Switching off:
Let go of the ON/OFF switch
.
Setting the stroke depth
You can use the stroke rate control to adjust the depth of the
engraving. A low setting is usually sufficient for the most common
applications.
Turn the stroke rate control
towards the + to increase the
stroke depth.
Turn the stroke rate control
towards the to decrease the
stroke depth.
NOTE
When you increase the stroke depth, make sure not to turn the
stroke rate control
too far in the direction of the +.
Otherwise, you will unscrew the control off the appliance.
PGG 15 C2
10 
GB
Changing the engraving tips
CAUTION! RISK OF INJURY!
Switch the appliance off and remove the power plug before
commencing any work to the appliance.
Change the engraving tip
as soon as it becomes worn
and no longer delivers the desired engraving results. Turn the
engraving tip lock anticlockwise until the engraving tip
can be removed.
Remove the spring and washer.
Slide the washer and spring onto a new engraving tip
. Then
insert it into the appliance and turn the engraving tip lock
clockwise to lock the tip.
Ensure that the engraving tip
is fixed correctly in place.
PGG 15 C2
GB
 11
Working procedures
You can use the mini engraver to create imaginative and unique
engravings. For example, you can permanently mark valuable items.
You can engrave numbers and letters onto metal, glass, wood,
plastic, ceramics, stone and leather. To do this, use the supplied
engraving templates .
Hold the appliance at an angle, in the same way you would
hold a pen.
Your arm should be resting on the table.
Move the engraving tip
over the workpiece while applying
gentle pressure. To find out the ideal engraving speed, practice
on a spare piece of material.
NOTE
The supplied engraving tip
is made of tungsten steel. It is
therefore not suitable for engraving electronic media such as
CDs, DVDs, etc. These materials and their readability could be
damaged.
PGG 15 C2
12 
GB
Cleaning
WARNING! RISK OF INJURY! Always remove
the plug from the power socket before all main-
tenance and cleaning work on the appliance.
Remove all dirt from the appliance. Use a dry cloth to do this.
Disposal
Disposal of the appliance
The packaging is made from environmentally friendly mate-
rial and can be disposed of at your local recycling plant.
Do not dispose of power tools in the normal
domestic waste!
European Directive 2012/19/EU requires that worn-out power tools
be collected separately and recycled in an environmentally compatible
manner.
Your local community or municipal authorities can provide informa-
tion on how to dispose of the worn-out appliance.
PGG 15 C2
GB
 13
Warranty
This appliance is provided with a 3-year warranty valid from the
date of purchase. This appliance has been manufactured with care
and inspected meticulously prior to delivery.
Please retain your receipt as proof of purchase. In the event of a war-
ranty claim, please contact your Customer Service unit by telephone.
This is the only way to guarantee free return of your goods.
NOTE
This warranty is valid only for material or manufacturing faults,
not for damage sustained during carriage, parts subject to
wear and tear or damage to fragile parts, e.g. switches.
This product is intended solely for private use and not for commercial
purposes. The warranty shall be deemed void in cases of misuse or
improper handling, use of force and modifications/repairs which
have not been carried out by one of our authorised Service centres.
Your statutory rights are not restricted by this warranty. The warranty
period is not prolonged by repairs effected under the warranty.
This also applies to replaced and repaired components.
Any damage and defects present at the time of purchase must be
reported immediately after unpacking, but no later than two days
after the date of purchase.
Repairs carried out after expiry of the warranty period shall be
subject to charge.
PGG 15 C2
14 
GB
Service
WARNING!
Have the power tool repaired by the Service centre or a
qualified electrician and only using genuine replacement
parts. This will ensure that the safety of the appliance is
maintained.
WARNING!
Always ensure that the power plug or the mains cable
is replaced only by the manufacturer of the appliance
or by an approved customer service provider. This will
ensure that the safety of the appliance is maintained.
NOTE
You can order spare parts (such as replacement templates and
tips) using our service hotline.
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
IAN 275634
Importer
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
PGG 15 C2
GB
 15
Translation of the original Conformity
Declaration
We, KOMPERNASS HANDELS GMBH, documents officer:
Mr. Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY,
hereby declare that this product complies with the following
standards, normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)
Applied harmonised standards:
EN 60745-1/A11:2010
EN ISO 12100:2010
EN 55014-1/A2:2011
EN 55014-2/A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
PGG 15 C2
16 
GB
Type designation of machine:
Power engraving tool PGG 15 C2
Year of manufacture: 02 - 2016
Serial number: IAN 275634
Bochum, 21/01/2016
Semi Uguzlu
- Quality Manager -
The right to effect technical changes in the context of further
development is reserved.
PGG 15 C2
HU
 17
Tartalomjegyzék
Bevezető ...................................18
Rendeltetésszerű használat .............................18
Felszereltség .........................................19
A csomag tartalma ....................................19
Műszaki adatok ......................................19
Általános biztonsági utasítások elektromos
kéziszerszámokhoz .................................................21
1. Munkahelyi biztonság ...............................22
2. Elektromos biztonság ................................22
3. Személyi biztonság .................................23
4. Az elektromos kéziszerszám használata és kezelése .......24
5. Szerviz ...........................................25
Használat ...................................25
Be- / kikapcsolás .....................................25
Löketmélység beállítása ................................26
Gravírozócsúcs cseréje ................................26
Munkavégzésre vonatkozó tudnivalók .....................27
Tisztítás ....................................28
Ártalmatlanítás ..............................28
A készülék ártalmatlanítása .............................28
Garancia ...................................29
Szerviz ..................................... 30
Gyártja .....................................30
Az eredeti megfelelőségi nyilatkozat fordítása ....31
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Parkside PGG 15 C2 Translation Of The Original Instructions

Kategória
Elektrické náradie
Typ
Translation Of The Original Instructions

V iných jazykoch