Parkside PGG 15 C2 Translation Of The Original Instructions

POWER ENGRAVING TOOL PGG 15 C2

IAN 275634

GRAVIERGERÄT

Originalbetriebsanleitung

POWER ENGRAVING TOOL

Translation of the original instructions

APARAT ZA GRAVIRANJE

Prevod originalnega navodila za uporabo

GRAVÍROZÓ KÉSZÜLÉK

Az originál használati utasítás fordítása

GRAVÍROVACÍ PŘÍSTROJ

Překlad originálního provozního návodu

GRAVÍROVAČKA

Preklad originálneho návodu na obsluhu

GB Translation of the original instructions Page 1

HU Az originál használati utasítás fordítása Oldal 17

SI Prevod originalnega navodila za uporabo Stran 33

CZ Překlad originálního provozního návodu Strana 51

SK Preklad originálneho návodu na obsluhu Strana 67

DE / AT / CH Originalbetriebsanleitung Seite 83

Before reading, unfold the page containing the illustrations and familiarise

yourself with all functions of the device.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg

a készülék mindegyik funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami

naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi

funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všet-

kými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen

Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

PGG 15 C2

GB

│

1 ■

Contents

Introduction .................................. 2

Intended use ..........................................2

Features .............................................3

Package contents ......................................3

Technical data ........................................3

General power tool safety warnings ............. 5

1. Work area safety ....................................6

2. Electrical safety .....................................6

3. Personal safety ......................................7

4. Power tool use and care ..............................8

5. Service ............................................9

Operation ................................... 9

Switching on and oﬀ ...................................9

Setting the stroke depth .................................9

Changing the engraving tips ............................10

Working procedures ...................................11

Cleaning ....................................12

Disposal ....................................12

Disposal of the appliance ...............................12

Warranty ...................................13

Service .....................................14

Importer ....................................14

Translation of the original Conformity Declaration . 15

PGG 15 C2

■ 2

│

GB

POWER ENGRAVING TOOL PGG 15 C2

Introduction

Congratulations on the purchase of your new appliance. You have

selected a high-quality product. The operating instructions are part

of this product. They contain important information on safety, usage

and disposal. Before using the product, familiarise yourself with all

handling and safety guidelines. Use the product only as described

and for the range of applications speciﬁed. Please also pass these

operating instructions on to any future owner.

Intended use

This appliance is intended for engraving or decorating materials

such as metal, plastic, glass, leather and stone. Any other usage

of or modiﬁcation to the appliance is deemed to be improper and

carries a signiﬁcant risk of accidents. The manufacturer accepts no

responsibility for damage(s) attributable to misuse. This appliance is

not intended for commercial use.

PGG 15 C2

GB

│

3 ■

Features

 ON/OFF switch

Stroke rate control

 Carrying lug

Power cable

Engraving tip

Engraving tip lock

Engraving templates

Package contents

1 power engraving tool PGG 15 C2

4 engraving templates

1 set of operating instructions

Technical data

Rated voltage: 230V

~

50Hz (alternating current)

Operating mode: periodic intermittent operation: S3 20%

Note: A duty cycle (in %) explicitly speciﬁes the maximum continu-

ous use and the subsequent rest period. In this case, for instance,

the tool needs a cooling period of eight minutes after two minutes of

operation.

Rated current: 0.15 A

Stroke rate: 6000 rpm

Approximate weight: 370 g

PGG 15 C2

■ 4

│

GB

Noise emission value:

Noise measurement value determined in accordance with EN 60745.

The A-rated noise level of the power tool is typically as follows:

Sound pressure level: L

pA

= 74.4 dB(A)

Uncertainty: K

pA

= 3 dB

Sound power level: L

WA

= 85.4 dB(A)

Uncertainty: K

WA

= 3 dB

Wear hearing protection!

Total vibration value:

a

h

= 1.582 m/s

2

Uncertainty K = 1.5 m/s

2

NOTE

► The vibration level speciﬁed in these instructions has been

measured in accordance with the standardised measuring

procedure speciﬁed in EN 60745 and can be used to make

equipment comparisons. The speciﬁed vibration emission

value can also be used to make an initial exposure estimate.

PGG 15 C2

GB

│

5 ■

WARNING!

► The vibration level varies in accordance with the use of the

power tool and may be higher than the value speciﬁed in

these instructions in some cases. Regular use of the electric

tool in such a way may cause the user to underestimate the

vibration. Try to keep the vibration loads as low as possible.

Measures to reduce the vibration load include wearing

gloves and limiting your working time. Wherein all states of

operation must be included (e.g. times when the power tool

is switched oﬀ and times where the power tool is switched

on but running without load).

General power tool

safety warnings

WARNING!

► Read all safety warnings and all instructions. Failure to follow

the warnings and instructions may result in electric shock, ﬁre

and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated

(corded/mains adapter) power tools or battery-operated (cordless)

power tool.

PGG 15 C2

■ 6

│

GB

1. Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in explosive atmospheres, such as

in the presence of ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased

risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling

or unplugging the power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a residual current device (RCD) protected supply. Use of

an RCD reduces the risk of electric shock.

PGG 15 C2

GB

│

7 ■

3. Personal safety

a) Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the inﬂuence of drugs, alcohol or medi-

cation. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protec-

tion. Protective equipment such as dust mask, non-skid safety

shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the oﬀ-

position before connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power

tool on. A wrench or a key left attached to a rotating part of the

power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in unexpected

situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep

your hair, clothing and gloves away from moving parts. Loose

clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly

used. Use of dust collection can reduce dust-related hazards.

PGG 15 C2

■ 8

│

GB

4. Power tool use and care

a) Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and

oﬀ. Any power tool that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery

pack from the power tool before making any adjustments, chang-

ing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instruc-

tions to operate the power tool. Power tools are dangerous in

the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of

moving parts, breakage of parts and any other condition that

may aﬀect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting

tools with sharp cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits etc. in accordance

with these instructions, taking into account the working condi-

tions and the work to be performed. Use of the power tool for

operations diﬀerent from those intended could result in a hazard-

ous situation.

PGG 15 C2

GB

│

9 ■

5. Service

a) Have your power tool serviced by a qualiﬁed repair person

using only identical replacement parts. This will ensure that the

safety of the power tool is maintained.

Operation

Never use the appliance for other purposes and only original parts/

accessories. Using attachments or accessory tools other than those

recommended in the operating instructions can lead to a risk of injury.

Switching on and oﬀ

♦ Insert the power plug into a mains wall socket.

Switching on:

♦ Press the ON/OFF switch

.

Switching oﬀ:

♦ Let go of the ON/OFF switch

.

Setting the stroke depth

You can use the stroke rate control to adjust the depth of the

engraving. A low setting is usually suﬃcient for the most common

applications.

♦ Turn the stroke rate control

towards the + to increase the

stroke depth.

♦ Turn the stroke rate control

towards the – to decrease the

stroke depth.

NOTE

► When you increase the stroke depth, make sure not to turn the

stroke rate control

too far in the direction of the +.

Otherwise, you will unscrew the control oﬀ the appliance.

PGG 15 C2

■ 10

│

GB

Changing the engraving tips

CAUTION! RISK OF INJURY!

► Switch the appliance oﬀ and remove the power plug before

commencing any work to the appliance.

♦ Change the engraving tip

as soon as it becomes worn

and no longer delivers the desired engraving results. Turn the

engraving tip lock anticlockwise until the engraving tip

can be removed.

♦ Remove the spring and washer.

♦ Slide the washer and spring onto a new engraving tip

. Then

insert it into the appliance and turn the engraving tip lock

clockwise to lock the tip.

♦ Ensure that the engraving tip

is ﬁxed correctly in place.

PGG 15 C2

GB

│

11 ■

Working procedures

You can use the mini engraver to create imaginative and unique

engravings. For example, you can permanently mark valuable items.

You can engrave numbers and letters onto metal, glass, wood,

plastic, ceramics, stone and leather. To do this, use the supplied

engraving templates .

♦ Hold the appliance at an angle, in the same way you would

hold a pen.

♦ Your arm should be resting on the table.

♦ Move the engraving tip

over the workpiece while applying

gentle pressure. To ﬁnd out the ideal engraving speed, practice

on a spare piece of material.

NOTE

► The supplied engraving tip

is made of tungsten steel. It is

therefore not suitable for engraving electronic media such as

CDs, DVDs, etc. These materials and their readability could be

damaged.

PGG 15 C2

■ 12

│

GB

Cleaning

WARNING! RISK OF INJURY! Always remove

the plug from the power socket before all main-

tenance and cleaning work on the appliance.

■ Remove all dirt from the appliance. Use a dry cloth to do this.

Disposal

Disposal of the appliance

The packaging is made from environmentally friendly mate-

rial and can be disposed of at your local recycling plant.

Do not dispose of power tools in the normal

domestic waste!

European Directive 2012/19/EU requires that worn-out power tools

be collected separately and recycled in an environmentally compatible

manner.

Your local community or municipal authorities can provide informa-

tion on how to dispose of the worn-out appliance.

PGG 15 C2

GB

│

13 ■

Warranty

This appliance is provided with a 3-year warranty valid from the

date of purchase. This appliance has been manufactured with care

and inspected meticulously prior to delivery.

Please retain your receipt as proof of purchase. In the event of a war-

ranty claim, please contact your Customer Service unit by telephone.

This is the only way to guarantee free return of your goods.

NOTE

► This warranty is valid only for material or manufacturing faults,

not for damage sustained during carriage, parts subject to

wear and tear or damage to fragile parts, e.g. switches.

This product is intended solely for private use and not for commercial

purposes. The warranty shall be deemed void in cases of misuse or

improper handling, use of force and modiﬁcations/repairs which

have not been carried out by one of our authorised Service centres.

Your statutory rights are not restricted by this warranty. The warranty

period is not prolonged by repairs eﬀected under the warranty.

This also applies to replaced and repaired components.

Any damage and defects present at the time of purchase must be

reported immediately after unpacking, but no later than two days

after the date of purchase.

Repairs carried out after expiry of the warranty period shall be

subject to charge.

PGG 15 C2

■ 14

│

GB

Service

WARNING!

■ Have the power tool repaired by the Service centre or a

qualiﬁed electrician and only using genuine replacement

parts. This will ensure that the safety of the appliance is

maintained.

WARNING!

■ Always ensure that the power plug or the mains cable

is replaced only by the manufacturer of the appliance

or by an approved customer service provider. This will

ensure that the safety of the appliance is maintained.

NOTE

► You can order spare parts (such as replacement templates and

tips) using our service hotline.

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 275634

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PGG 15 C2

GB

│

15 ■

Translation of the original Conformity

Declaration

We, KOMPERNASS HANDELS GMBH, documents oﬃcer:

Mr. Semi Uguzlu, BURGSTR. 21, 44867 BOCHUM, GERMANY,

hereby declare that this product complies with the following

standards, normative documents and EC directives:

Machinery Directive

(2006/42/EC)

EMC (Electromagnetic Compatibility)

(2014/30/EU)

RoHS Directive

(2011/65/EU)

Applied harmonised standards:

EN 60745-1/A11:2010

EN ISO 12100:2010

EN 55014-1/A2:2011

EN 55014-2/A2:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

PGG 15 C2

■ 16

│

GB

Type designation of machine:

Power engraving tool PGG 15 C2

Year of manufacture: 02 - 2016

Serial number: IAN 275634

Bochum, 21/01/2016

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context of further

development is reserved.

PGG 15 C2

HU

│

17 ■

Tartalomjegyzék

Bevezető ...................................18

Rendeltetésszerű használat .............................18

Felszereltség .........................................19

A csomag tartalma ....................................19

Műszaki adatok ......................................19

Általános biztonsági utasítások elektromos

kéziszerszámokhoz .................................................21

1. Munkahelyi biztonság ...............................22

2. Elektromos biztonság ................................22

3. Személyi biztonság .................................23

4. Az elektromos kéziszerszám használata és kezelése .......24

5. Szerviz ...........................................25

Használat ...................................25

Be- / kikapcsolás .....................................25

Löketmélység beállítása ................................26

Gravírozócsúcs cseréje ................................26

Munkavégzésre vonatkozó tudnivalók .....................27

Tisztítás ....................................28

Ártalmatlanítás ..............................28

A készülék ártalmatlanítása .............................28

Garancia ...................................29

Szerviz ..................................... 30

Gyártja .....................................30

Az eredeti megfelelőségi nyilatkozat fordítása ....31

Stránka sa načítava ...

Parkside PGG 15 C2 Translation Of The Original Instructions

Parkside PGG 15 C2 Translation Of The Original Instructions

V iných jazykoch

Súvisiace články

Ďalšie dokumenty