FLORABEST FGS 3.6 A1 Translation Of The Original Instructions

®

Cordless Grass & shrub Trimmer FGs 3.6 a1

akku-Gras- und

sTrauChsChere

Originalbetriebsanleitung

akumuláTorové nůžky

na Trávu a keře

Překlad originálního provozního návodu

akumuláTorové nožniCe na

Trávnik a kríky

Preklad originá lneho návodu na obsluhu

Cordless Grass &

shrub Trimmer

Translation of the original instructions

akumulaTorske škarje za rezanje

Trave in Grmičevja

Prevod originalnega navodila za uporabo

IAN 102887

102887_flo_Akku-Gras-und-Strauchschere_cover_SI_CZ_SK.indd 2 10.11.14 16:07

GB Translationof the original instructions Page 4

SI Prevod originalnega navodila za uporabo Stran 19

CZ Překlad originálního provozního návodu Strana 35

SK Preklad originálneho návodu na obsluhu Strana 51

DE / AT / CH Originalbetriebsanleitung Seite 67

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

102887_flo_Akku-Gras-und-Strauchschere_cover_SI_CZ_SK.indd 3 10.11.14 16:07

17

9

12

13

10

1

1 3

165 6

7

4

3

5

6

7

8

2

1

9

10

11

12

13

14

16

17

4

GB

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product. During production,

this equipment has been checked for qual-

ity and subjected to a nal inspection. The

functionality of your equipment is therefore

guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied. Keep this

manual safely and in the event that

the product is passed on, hand over

all documents to the third party.

Intended use

The unit is to be used for cutting and trim-

ming twigs on hedges, bushes and shrubs

and for trimming grass at the edges and

on smaller surfaces in domestic application

only.

The unit is only to be used by adults.

People under 16 should only use this unit

under adult supervision.

Any other use not specically mentioned

in this manual can lead to damage to the

unit and may present a serious hazard to

the user.

The operator or user is responsible for ac-

cidents or damage to other persons or their

property.

This equipment is not suitable for commer-

cial use. Commercial use will invalidate the

guarantee.

Contents

Introduction .................................4

Intended use ................................ 4

General description ......................5

Extent of the delivery .......................5

Overview ....................................... 5

Function description.........................6

Technical data .............................. 6

Safety Instructions........................7

Symbols ......................................... 7

General safety instructions for power

tools ..............................................7

Special Safety Directions for the

cordless grass & shrub cutter ..........10

Safety Directions for the battery

charger ........................................11

Charging process .......................12

Operation ..................................12

Switching on and off .....................12

Inserting/replacing the blade .........13

General working instructions ..........13

Use as a grass trimmer ..................13

Use as a hedge trimmer ................. 13

Cleaning/Maintenance ...............14

Storage ......................................14

Disposal and the environment ....14

Telescopic arm as an accessory ..15

Assembling the telescopic arm ........15

Adjust the height of the telescopic

arm .............................................15

Adjusting the working angle ........... 15

Switching on and off

(with telescopic arm) .....................15

Working with the telescopic arm .....15

Spare parts/Accessories ............. 16

Trouble shooting ........................16

Guarantee .................................17

Repair Service ............................18

Service-Center ............................18

Importer .................................... 18

Translation of the original EC

declaration of conformity ........... 84

Exploded Drawings ....................87

5

GB

The manufacturer will not be held respon-

sible for damage or injuries caused by use

outside that stipulated by the manual or by

improper handling.

General description

The illustration of the princi-

pal functioning parts can be

found on the front and back

foldout pages.

Extent of the delivery

Carefully unpack the appliance and check

that it is complete.

Dispose of the packaging material cor-

rectly.

- Device with mounted grass shear

blade, blade guard, safety key

- Shrub shear blade + blade guard

- Recharger

- Instruction Manual

Device is delivered without a

telescopic arm. Alternatively, a

telescopic arm including wheels

can be ordered (see “Spare parts/

accessories”).

Overview

Equipment

1 Cutter head

2 Switch lock, unit

3 Lever to turn the cutter head

4 Unit handle

5 Charging socket + plug socket

for plug connection telescopic

arm

6 Charge display (LED)

7 Safety key

8 On/off switch, unit

Cutter

9 Grass shear blade

10 Unlock button for grass cutter

11 Blade guard for grass shear

blade

12 Shrub shear blade

13 Blade guard for shrub shear

blade

14 Unlock button for shrub cutter

Battery charger

16 Power supply unit

17 Recharger cable plug

18 Telescopic arm with wheels (not

included in the scope of delivery)

19 Guide rail

20 Equipment holder

21 Plug connection

22 Adjusting screw for length adjust-

ment

23 Release switch

24 Switch lock, telescopic shaft

25 On/off switch, telescopic shaft

6

GB

Function description

The cordless grass & shrub trimmer is a

combination unit with two interchangeable

cutting devices. These are coated with plas-

tic (Teon non-stick coating) to prevent rust.

For use as a shrub trimmer, a double-sided

blade block is used as the cutting head.

The catching blades are round off at the

side to prevent accidents, and positioned

in an offset arrangement to reduce the

risk of injury. A cutting head with several

blades is provided for use as a grass trim-

mer. The safety key protects the devices

from being started unintentionally.

Please read the following descriptions for

the function of the various controlling parts

of the unit.

Technical data

Unit

Motor voltage ............................ 3.6 V

Rated speed ..........................1000 min

-1

Protection class ................................... III

Protection category.......................... IP20

Grass-trimming blade

Cutting width ............................ 73 mm

Blade width .............................. 80 mm

Shrub-trimming blade

Cutting length ........................120 mm

Distance between teeth ....approx. 8 mm

Weight (incl. accessories) ..approx 0.85 kg

Sound pressure level

(L

pA

) .................. 57 dB(A), K

pA

=3 dB(A)

Sound power level (L

wA

)

guaranteed ...........................92 dB(A)

measured ....... 79.1 dB(A); K

wA

=3 dB(A)

Vibration (a

h

)

at handle .........1.39 m/s

2

, K=1.5 m/s

2

Battery (Li-Ion)

Nominal voltage ......... 3.6 V

1.3 Ah

Loading time .................. approx. 3-5 h

Charger ............................. DK-MGB-48

Voltage input ...................230 V~, 50 Hz

Nominal consumption ...................... 8 W

Voltage output ...............................4.8 V

Recharging current .....................450 mA

Performance output.......................3.6 VA

Protection class ...............................

II

Protection category...........................IPX0

The noise and vibration levels have been

calculated according to the norms stated

in the conformity statement. Technical and

optical alterations to serve progress may

be made without notice. All measurements,

instructions and other data given in this

manual are therefore given without guar-

antee of correctness. Legal claims made

on the basis of this manual are therefore

excluded.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another. The stated

vibration emission value may also be used

for a preliminary exposure assessment.

Warning: The vibration emission

value may differ during actual use

of the power tool from the stated

value depending on the manner in

which the power tool is used.Safety

precautions aimed at protecting the

user should be based on estimated

exposure under actual usage condi-

tions (all parts of the operating cycle

are to be considered, including, for

example, times during which the

power tool is turned off and times

when the tool is turned on but is run-

ning idle).

7

GB

Safety Instructions

This unit can cause serious in-

jury if not used correctly. Be-

fore using the unit, carefully

read through the instruction

manual and familiarise your-

self with all of its controls.

Symbols

Symbols on the unit

Remember that the cutting equip-

ment will continue to move after

switching the unit off.

Attention!

Before using for the rst time, care-

fully read through the user manual.

Do not use the unit during rain, bad

weather damp surroundings or on

wet grass or hedges.

dB

L

WA

Guaranteed sound power level

Do not dispose of the device

with the battery installed in

household waste.

Cutting length Shrub shear blade

Symbols on the recharger

Read the manual.

Pole orientation

The recharger is for indoor use

only.

Protection class II

Machines do not belong with do-

mestic waste.

Symbols in the manual

Warning symbols (instead of

the exclamation mark, the

danger may be explained)

with information on damage

and injury prevention.

Instruction symbols (the instruction

may be explained at the place of

the exclamation mark) with informa-

tion on preventing damage.

Help symbols with information on

improving tool handling.

General safety instructions

for power tools

WARNING! Read all safety

directions and instructions.

Omissions in the compliance with

safety directions and instructions

can cause electrical shock, re

and/or severe injuries.

Retain all safety directions and in-

structions for future use.

The term “Power Tools” used in the safety

instructions refers to mains-operated power

tools (with power cord) and to battery-op-

erated power tools (without power cord).

1) WORK AREA SAFETY

a) Keep work area clean and well

lit. Cluttered or dark areas invite ac-

cidents.

b) Do not operate power tools in

explosive atmospheres, such as

in the presence of ammable

8

GB

Iiquids, gases or dust. Power tools

create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders

away while operating a power

tool. Distractions can cause you to

lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match

the outlet. Never modify the

plug in any way. Do not use

any adapter plugs with earthed

(grounded) power tools. Unmodi-

ed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with

earthed or grounded surfaces,

such as pipes, radiators, ranges

and refrigerators. There is an

increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to

rain or wet conditions. Water

entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never

use the cord for carrying, pulling

or unplugging the power tool.

Keep cord away from heat, oil,

sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a

damp location is unavoidable,

use a residual current device

(RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense

when operating a power tool.

Do not use a power tool while

you are tired or under the inu-

ence of drugs, alcohol or medi-

cation. A moment of inattention white

operating power tools may result in seri-

ous personal injury.

b) Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off-

position before connecting to

power source and/or battery

pack, picking up or carrying the

tool. Carrying power tools with your

nger on the switch or energising pow-

er tools that have the switch on invites

accidents.

d) Remove any adjusting key or

wrench before turning the pow-

er tool on. A wrench or a key left

attached to a rotating part of the power

tool may result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear

loose clothing or jewellery. Keep

your hair, clothing and gloves

away from moving parts. Loose

clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the

connection of dust extraction

and collection facilities, ensure

9

GB

these are connected and prop-

erly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the

switch does not turn it on and

off. Any power tool that cannot be

controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the

power source and/or the bat-

tery pack from the power tool

before making any adjust

-ments, changing accessories, or

storing power tools. Such preven-

tive safety measures reduce the risk of

starting the power tool accidentaIly.

d) Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions

to operate the power tool. Power

tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check

for misalignment or binding

of moving parts, breakage of

parts and any other condition

that may affect the power tool’s

operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly main-

tained power tools.

f) Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are less

Iikely to bind and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking

into account the working condi-

tions and the work to be per-

formed. Use of the power tool for op-

erations different from those intended

could result in a hazardous situation.

5) CAREFUL HANDLING AND USE

OF BATTERY DEVICES

a) Charge the batteries only in

chargers that are recommended

by the manufacturer. Risk of re if a

charger that is suitable for a specic type

of battery is used with other batteries.

b) In the power tools, use only the

batteries designed for the pur-

pose. The use of other batteries may

result in injuries and risk of re.

c) Keep the unused battery away

from paper clips, coins, keys,

nails, screws and other small

metal objects, which could

cause bridging of the contacts.

A short circuit between the battery con-

tacts may cause burns or re.

d) If used incorrectly, liquid may

leak from the battery. Avoid

contact with this. In the event of

accidental contact, rinse off with

water. If the liquid gets into

eyes, seek medical assistance.

Leaking battery uid may cause skin

irritations or burns.

6) SERVICE

a) Have your power tool serviced

by a qualied repair person us-

ing only identical replacement

parts. This will ensure that the safety

of the power tool is maintained.

10

GB

Special Safety Directions for

the cordless grass & shrub

cutter

1) SPECIAL SAFETY DIRECTIONS

FOR HEDGE TRIMMERS

a) Keep all body parts away from

the blade. Do not attempt to re-

move clippings while the blade

is operating or to hold on to

material which is to be cut. Only

remove trapped clippings when

the tool is switched off. One mo-

ment of carelessness in the usage of

the hedge trimmer can lead to severe

injury.

b) Carry the hedge trimmer at

the handle with an idle blade.

Always pull on the protective

cover during transport and stor-

age of the hedge trimmer.

Careful handling of the tool reduces

the risk of injury from the blade.

c) Hold the power tool only on the

insulated handle surfaces, as

the cutting blade may come into

contact with concealed power

cables. Contact between the cutting

blade and a live cable may render me-

tallic components live and result in an

electric shock.

d) Before the work, search the

hedge for concealed objects,

e.g. cable etc. To avoid damaging

the equipment.

e) Hold the hedge trimmer cor-

rectly, e.g. with both hands on

the handles, if there are two

handles. Loss of control of the equip-

ment may result in injuries.

f) Wear suitable clothing and

work clothes when working

with the equipment. Do not hold

the equipment by the cutting

blade or lift it on the cutting

blade. Contact with the cutting blade

can cause injuries.

2) FURTHER SAFETY DIRECTIONS

For your personal safety:

Wear suitable work clothes such

as boots with non-slip soles, sturdy

long trousers, gloves and goggles.

Hearing protection must be used

in case the device is used over

prolonged periods of time. Do

not wear long owing clothing or

jewellery, as this may be caught by

moving parts. Do not use this tool

while walking barefooted or while

wearing open sandals.

a) Only switch on the tool when

hands, feet and all other body

parts are at a secure distance to

the tool. Risk of injury from cuts.

b) Take care that you do not injure

your hands and feet with the

cutting elements.

c) Remove the power supply unit

before working with the equip-

ment. Do not use extension

cables. The power supply unit

is to be used only in enclosed

spaces. Water entry increases the risk

of electric shock.

d) Do not use the shrub cutter in

combination with the telescopic

shaft. There is a risk of cut wounds.

e) The tool is designed to trim

hedges. Do not use the tool to

cut branches, hard wood or oth-

er. To avoid damaging the equipment.

f) Do not attempt to dislodge a

blocked/trapped blade before

switching the tool off. There is a

11

GB

risk of injury.

g) Always switch off the tool and remove

the battery (if applicable)

- if you leave the tool unsupervised

- before removing jams

- before control- maintenance- or

cleaning tasks

- if you have come into contact with

a foreign object

- whenever the machine starts to vi-

brate uncontrollably

How to avoid accidents and injuries.

3) SPECIAL SAFETY DIRECTIONS

FOR BATTERY-OPERATED TOOLS

a) Do not subject the battery to

strong sunlight over long pe-

riods and do not leave it on a

heater. Heat damages the battery

and there is a risk of explosion.

b) Allow a hot battery to cool be-

fore charging.

c) Do not open up the battery and

avoid mechanical damage to

the battery. Risk of short circuit and

fumes may be emitted that irritate the

respiratory tract. Ensure fresh air and

seek medical assistance in the event of

discomfort.

Safety Directions for the

battery charger

1) CORRECT HANDLING OF THE

BATTERY CHARGER

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory

or mental capabilities or lack of ex-

perience and knowledge if they have

been given supervision or instruction

concerning use of the appliance in a

safe way and understand the hazards

involved.

• Children shall not play with the appli-

ance. Cleaning and user maintenance

shall not be made by children without

supervision.

• To charge the battery, use only

the charger supplied. Risk of re

and explosion. This ensures that the

safety of the device is maintained.

• Before each use, check the

charger, cable and plug and

have them repaired by quali-

ed professionals and only with

original parts. Do not use a de-

fective charger and do not open

it up yourself. This ensures that the

safety of the device is maintained.

• Connect the charger only to a

socket with an earth. Ensure

that the mains voltage matches

the specications on the charger

rating plate. Risk of electric shock.

• Disconnect the charger from the

mains before closing or open-

ing connection to the battery /

power tool / device. This ensures

that the battery and charger are not

damaged.

• Keep the charger clean and

away from wet and rain. Do

not use the charger outdoors.

Dirt and the entry of water increase the

risk of electric shock.

• Operate the charger only with

the appropriate original bat-

teries. Charging other batteries may

result in injuries and risk of re.

• Avoid mechanical damage to

the charger. This can result in inter-

nal short circuits.

• Do not operate the charger on a

combustible surface (e.g. paper,

textiles). Risk of re due to heating

12

GB

during charging.

• If the power cable for this

equipment is damaged, it must

be replaced by the manufac-

turer, a customer service agent

of the same or a similarly quali-

ed person in order to prevent

hazards.

• Do not use the charger to charge non-

rechargeable batteries.

Charging process

Do not expose the battery to

extreme conditions such as

heat and impact. There is a

risk of injury from leaking

electrolyte solution! In case

of contact, rinse with water

or neutraliser and consult a

doctor if contact has occurred

with eyes etc.

Charge the battery only in

dry areas.

Do not switch on the device

while charging it and make

sure that the safety key (

7) has been removed.

There is a risk of injury from

electric shock.

Ensure that the equipment is

charged for no longer than

3-5hours without interruption. The

battery and equipment could be

damaged and they consume energy

unnecessarily in case of longer

charging time. Overcharging invali-

dates the guarantee.

• Before initial use, charge the battery

installed in the equipment. Do not

charge the battery for several short pe-

riods in succession.

• Use the charger supplied to charge the

Li-ion battery installed in the equipment.

• Recharge the battery if the equipment

runs too slowly.

• In all cases, observe the applicable

safety information as well as the regula-

tions and directions for environmental

protection.

• Defects resulting from improper han-

dling are not subject to the guarantee.

1. Remove the safety key (7).

2. Connect the charger cable plug

(17) with the charger socket on

the tool (5).

3. Connect the power supply unit

(16) to a socket.

The charging indicator (6) lights

up:

Red: Equipment charging.

Green: Charging nished.

The recommended charging time

is max. 3 – 5 hours.

4. After the recharging process is

completed, rst unplug the charg-

er from the wall outlet, and then

remove the charger cable plug

from the tool.

Operation

Keep to noise abatement regulations

and other by-laws.

Switching on and off

1. Remove the blade guard (11/14)

before switching the unit on.

2. Insert the safety key (7) into the

device.

3. To switch on, hold the switch lock

(2) depressed and operate the

on/off switch (8). Then release

13

GB

the switch lock.

The equipment runs at top

speed.

4. In order to switch off, let go of

the on/off switch (8).

After switching the unit

off, the blades take a short

time to stop moving. Let the

blades come to a complete

standstill. Do not touch the

moving blades and do not

try to stop them moving. In-

jury hazard!

Inserting/replacing the blade

Prior to each exchange of the

blades, make sure the device

is switched off and the safety

key and in order to avoid

danger and injuries!

Remove blade

1. Press the unlock buttons (10/13)

on the blade and remove the

entire blade.

Insert blade

2. Insert the grass shear blade (9) or

the shrub shear blade (12) into

the recess in the cutter head (1).

3. Press the blade into the direction

of the cutter head (1). It locks

into place audibly.

General working instructions

While trimming, take care that there

are no objects such as wire, metal

parts, stones etc. come into contact

with the blades. This can lead to

cutting head damage. If the blades

become blocked by solid objects,

switch off the unit at once.

• Check the grass and bush trimmer

blades for obvious defects such as

loose, worn or damaged parts. Check

that the screws are seated rmly in the

blade block.

• Remove the power supply unit before

working with the equipment. Do not

use extension cables. The power sup-

ply unit is to be used only in enclosed

spaces.

• Only use sharp blades to achieve a

good cutting performance and pre-

serve the battery.

• Do not work the unit so hard that it

comes to a standstill.

• Pay attention to the instructions on unit

maintenance and cleaning.

Use as a grass trimmer

• Grass is best cut when dry and not too

long.

Adjusting the working angle

For a comfortable edge cut, the cutter head

(1) can be rotated by 90° to the right or left.

1. Operate the lever (3) and turn

the cutter head (1) into the de-

sired position.

2. Release the lever (3), the cutter

head locks into place.

Use as a hedge trimmer

• Move the unit forward evenly.

• The double-sided cutting heads enable

cutting in both directions or by swing-

ing the unit from side to side.

14

GB

Cleaning/Maintenance

Leave any work not covered

in this manual to our Service

Centre. Only use original

parts. There is a risk of injury!

Ensure that the safety key ( 7) is

removed before all tasks.

Never use cleaning agents or sol-

vents, which can cause irreparable

damage to the unit. Chemicals can

attack the plastic components on the

unit.

Wear gloves when handling the

blades (

9/12). There is a risk of

injury from cuts!

Clean and service the unit regularly as fol-

lows. This guarantees a long life for your

unit:

• Check the covers and guards for dam-

age and correct position. If necessary,

replace.

• Keep the ventilation slits, motor housing

and handles on the equipment clean. To

do this, use a damp cloth or brush.

• Always keep the blade clean.

After using the equipment, it is impera-

tive to:

- Clean the blade

(with an oily cloth);

- Oil the blade shaft

with an oil can or

spray.

• Slight notches on the blades can be

evened out. For this, sand down the

blades with an oil stone. Only sharp

blades can cut properly.

• Blunt, bent or damaged blades must be

changed.

We are not liable for damage caused by the

use of the unit if the original cause was im-

proper repair or the use of non-original parts

or through use other than that designated in

this manual.

Storage

• Keep the equipment in the blade guard

supplied, dry and out of reach of chil-

dren.

• Store the battery only in a partially

charged state. The state of charge should

be 40 – 60 % over a longer storage pe-

riod.

• Store the equipment between 10° C and

25° C. During storage, avoid extreme cold

or heat so the battery does not lose power.

• During a longer storage period, check

the state of charge of the battery and

recharge if necessary roughly every

3months.

Disposal and the

environment

Be environmentally friendly. Return the tool,

accessories and packaging to a recycling

centre when you have nished with them.

Machines do not belong with domes-

tic waste.

Do not dispose of the device

with the battery installed in

household waste, re (risk of ex-

plosion) or water. Damaged batteries may

damage the environment and your health if

toxic fumes or liquids leak out.

• Dispose of the equipment with the bat-

tery discharged. Do not open the equip-

ment or the battery.

• Dispose of the equipment in accordance

15

GB

with the local regulations. Take the

equipment to a collection point, where

it will be recycled in an environmentally

friendly manner. For information about

this, ask your local waste management

company or our service centre.

• Defective units returned to us will be

disposed of for free.

• Place cut branches in compost and not

in the dustbin.

Telescopic arm as an

accessory

Ensure that the safety key ( 7) is

removed before all tasks.

Device is delivered without a telescop-

ic arm. Alternatively, a telescopic arm

including wheels can be ordered (see

“Spare parts/accessories”).

Assembling the telescopic arm

Putting the telescopic arm

together:

1. Put both parts of the telescopic

arm (18) together and tighten the

screw.

Make sure that the cable is not

clamped.

Assembling/dismantling

the telescopic arm:

2. Push the device along the guide

rail (19) into the equipment

holder (20) of the telescopic arm.

It locks into place audibly.

3. Plug the plug connection (21) into

the charging socket (5) on the

back of the equipment handle (4).

4. To dismantle, release the plug

connection (21). Press the unlock

button on the bottom side of the

equipment holder (20) of the

telescopic arm and pull the device

out (see small image).

Adjust the height of the tel-

escopic arm

Adjust the length of the telescopic arm

for your size with the help of the ad-

justing screw (22).

Adjusting the working angle

For a comfortable edge cut, the equipment

holder (20) of the telescopic arm can be ro-

tated to the right or left (90°).

Set the desired position by pulling

the release switch (23) and rotating

the equipment holder (20) of the tel-

escopic arm. The equipment holder

locks into the desired position when

the release switch is released.

Switching on and off

(with telescopic arm)

1. Remove the blade guard (

11/14) before switching the de-

vice on.

2. Insert the safety key (

7) into the

device.

3. To switch on, hold the switch lock (24)

on the handle of the telescopic arm

and simultaneously press the on/off

switch (25). Release the switch lock,

device runs at top speed.

4. To turn it off, release the on/off

switch (25).

Working with the telescopic arm

• Slowly push the device on the wheels

over the oor. By doing so, you will

achieve an even cutting height.

16

GB

Spare parts/Accessories

Spare parts and accessories can be obtained at

www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone

(see “Service-Center” page 18). Please have the order number mentioned below ready.

Item Description Order No.

7 Safety key 91103520

9/11 Grass shear blade + blade gard 91103521

12/14 Shrub shear blade + blade gard 91103522

16/17 Battery charger EU 80001071

18 Telescopic shaft with carrier 80002070

Trouble shooting

Problem Possible Cause Error correction

Device doesn‘t

start

Equipment is not charged

Charge equipment (see „Charging

process“)

Switch lock (

2) has not

been operated properly

Switch on (see „Operation“)

On/off switch (

8) may

be defective

Repair by Service Centre

Safety key (

7) not in-

serted

Insert safety key (see "Operation")

Bad cutting results

Too much friction due to

lack of lubrication

Lubricate blade (

9/12)

(see „Cleaning/Maintenance“)

Dirty blade

(

9/12)

Clean blade (see „Cleaning/Mainte-

nance“)

Blade (

9/12) is blunt

or has nicks

Sharpen blade (see „Cleaning/

Maintenance“) or replace (see „Spare

parts/Accessories“)

Blade (

9/12) is dam-

aged

Replace blade (see „Spare parts/

Accessories“)

17

GB

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect

occurs within three years of the date of

purchase of this product, we will repair or

replace – at our choice – the product for

you free of charge. This guarantee requires

the defective equipment and proof of pur-

chase to be presented within the three-year

period with a brief written description of

what constitutes the defect and when it oc-

curred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts that

are subject to normal wear and may there-

fore be considered as wearing parts (e.g.

cutter bars and carbon brushes) or to cover

damage to breakable parts (e.g. switches,

batteries).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue,

please follow the following directions:

• Please have the receipt and identica-

tion number (IAN 102887) ready as

proof of purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

18

GB

• After consultation with our customer

service, a product recorded as defec-

tive can be sent postage paid to the

service address communicated to you,

with the proof of purchase (receipt)

and specication of what constitutes

the defect and when it occurred. In or-

der to avoid acceptance problems and

additional costs, please be sure to use

only the address communicated to you.

Ensure that the consignment is not sent

carriage forward or by bulky goods,

express or other special freight. Please

send the equipment inc. all accessories

supplied at the time of purchase and

ensure adequate, safe transport pack-

aging.

Repair Service

For a charge, repairs not covered by the

guarantee can be carried out by our ser-

vice branch, which will be happy to issue

a cost estimate for you.

We can handle only equipment that has

been sent with adequate packaging and

postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 102887

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

63762 Großostheim

Germany

www.grizzly-service.eu

GB

19

SI

Predgovor

Čestitke ob nakupu vaše nove naprave. Od-

ločili ste se za visokokakovosten izdelek.

Kakovost naprave je bila preverjena med

postopkom proizvodnje in pri končnem pre-

verjanju, s čimer je zagotovljeno pravilno

delovanje vaše naprave.

Izdelku so priložena navodila za

uporabo. Vsebujejo pomembna

navodila glede varnosti uporabe in

odstranitve. Pred uporabo izdelka

se seznanite z navodili za uporabo

in varnostnimi navodili. Izdelek upo-

rabljajte zgolj na opisani način in v

naštete namene.

Navodila skrbno shranite in pri

predaji naprave tretji osebi priložite

tudi vso dokumentacijo.

Namen uporabe

Naprava je namenjena samo rezanju in

obrezovanju tankih poganjkov pri živi meji,

grmovju in okrasnih grmovjih ter košnji trave

ob robovih ter na manjših površinah okoli

hiše.

To orodje ni primerno za uporabo v komer-

cialne namene. V primeru uporabe v komer-

cialne namene ugasne pravica do uveljavlja-

nja garancije.

Napravo lahko uporabljajo odrasle osebe.

Mladostniki nad 16 let lahko uporabljajo

napravo le pod nadzorom.

Vsaka druga vrsta uporabe, ki v teh navodi-

lih za uporabo ni izrecno dovoljena, lahko

privede do poškodb naprave in predstavlja

resno nevarnost za uporabnika.

Uporabnik je odgovoren za poškodbe dru-

gih oseb in povzročeno materialno škodo.

Proizvajalec ne odgovarja za škodo, nastalo

zaradi nenamenske ali napačne uporabe

naprave.

Kazalo

Predgovor .................................. 19

Namen uporabe ........................19

Splošni opis ...............................20

Obseg dobave ..............................20

Opis delovanja ..............................20

Pregled .........................................20

Tehnični podatki .........................21

Varnostni napotki ......................21

Slikovni znaki ................................21

Splošni varnostni predpisi za

električna orodja ............................22

Posebni varnostni predpisi za akumula-

torske škarje za travo in grmičevje ...25

Varnostni predpisi za polnilnik akumula-

torskih baterij .................................... 26

Postopek polnjenja ....................27

Uporaba ....................................28

Vklop in Izklop ..............................28

Namestitev/menjava rezila .............28

Splošni delovni napotki ...................28

Uporaba kot škarje za travo ............ 28

Uporaba kot škarje za grmovje ........29

Čiščenje/Vzdrževanje .................29

Shranjevanje ..............................29

Odstranitev/varstvo okolja ........30

Teleskopski ročaj kot dodatna

oprema ...................................... 31

Montaža teleskopskega ročaja ........31

Nastavitev višine teleskopskega

ročaja ..........................................31

Nastavitev delovnega kota .............. 31

Vklop in izklop

(s teleskopskim ročajem) .................31

Delo s teleskopskim ročajem ............ 31

Nadomestni deli/Pribor .............32

Odpravljanje napak ................... 32

Garancijski list ...........................33

Prevod originalne izjave o

skladnosti CE .............................84

Eksplozijska risba ......................87

20

SI

Splošni opis

Slike najdete na prednji in

zadnji strani pokrova.

Obseg dobave

Orodje vzemite iz embalaže in preverite,

ali je popolno. Embalažo odstranite v skla-

du s predpisi.

- Orodje z nameščenim rezilom škarij

za travo, zaščito rezila in varnostnim

ključem

- Rezilo škarij za grmičevje + zaščita

rezila

- Polnilnik baterij

- Navodila za uporabo

Orodje je dobavljeno brez teleskop-

skega ročaja. Kot dodatno opremo

je mogoče naročiti teleskopski ročaj

s kolesi (glejte „Nadomestni deli/

pribor“).

Opis delovanja

Škarje za travo in grmičevje na baterije so

kombinirana naprava z dvema zamenljivi-

ma rezalnima pripravama.

Prijemalni zobci so iz varnostnih razlogov

ob strani zaobljeni in nameščeni z zami-

kom, da se zmanjša nevarnost poškodb.

Pri uporabi kot škarje za travo se kot rezal-

na priprava uporabi rezilo z večimi zobci.

Varnostni ključ zagotavlja zaščito pred ne-

namernim vklopom.

Opise delovanja upravljalnih delov najdete

spodaj.

Pregled

Orodje

1 Rezalna glava

2 Zapora vklopa, naprava

3 Ročica za vrtenje rezalne glave

4 Ročaj naprave

5 Polnilna doza + vtični nastavek

za vtični spoj teleskopskega ro-

čaja

6 Prikaz polnjenja (LED)

7 Varnostni ključ

8 Stikalo za Vklop/Izklop, napra-

va

Rezalna priprava

9 Rezilo škarij za travo

10 Tipka za sprostitev škarij za tra-

vo

11 Zaščita rezila škarij za travo

12 Rezilo škarij za grmičevje

13 Zaščita rezila škarij za grmičevje

14 Tipka za sprostitev škarij za gr-

mičevje

Polnilnik baterij

16 Polnilnik

17 Vtič kabla polnilnika

 18 Teleskopskiročajskolesi(ni

vključenvobsegdobave)

19 Vodilo

20 ležišče orodja

21 Vtični spoj

22 Nastavitveni vijak za nastavitev

dolžine

23 Stikalo za deblokiranje

24 Zapora vklopa, teleskopski ročaj

25 Stikalo za Vklop/Izklop, tele-

skopski ročaj

Stránka sa načítava ...

FLORABEST FGS 3.6 A1 Translation Of The Original Instructions

FLORABEST FGS 3.6 A1 Translation Of The Original Instructions

V iných jazykoch

Ďalšie dokumenty