Interface Introduction

Read all information and instructions in this document carefully

before using the device and keep it for further reference.

For more device information and instructions, please visit our

website at https://www.hikvision.com. You can also refer to other

documents (if any) accompanying the device or scan the QR code (if

any) on the packaging to get more information.

About this Document

The document includes instructions for using and managing the

product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The

information contained in the document is subject to change,

Please use this document under the guidance of professionals.

Trademarks

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions. Other trademarks

and logos mentioned are the properties of their respective

owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS

MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,

SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH

ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,

BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,

CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,

WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING

NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN

CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR

LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET

PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL

NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,

Safety Instruction

These instructions are intended to ensure that the user can use

the product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws, electrical

safety regulations, and fire prevention regulations.

Electricity

In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. The

fire or electric shock. Do not touch the bare components (such as

the metal contacts of the inlets) and wait for at least 5 minutes,

since electricity may still exist after the device is powered off.

Battery

Do not ingest battery. Chemical burn hazard! This product

contains a coin/button cell battery. If the coin/button cell battery

is swallowed, it can cause severe internal burns in just 2 hours and

can lead to death. Keep new and used batteries away from

children. If the battery compartment does not close securely, stop

using the product and keep it away from children. If you think

Do not dispose of the battery into fire or a hot oven, or

mechanically crush or cut the battery, which may result in an

explosion. Do not leave the battery in an extremely high

temperature surrounding environment, which may result in an

explosion or the leakage of flammable liquid or gas. Do not subject

the battery to extremely low air pressure, which may result in an

explosion or the leakage of flammable liquid or gas. + identifies

the positive terminal(s) of equipment which is used with, or

generates direct current. - identifies the negative terminal(s) of

equipment which is used with, or generates direct current.

one-half hour after switching off before

handling parts. This sticker is to indicate

Install the device according to the instructions in this manual. To

installation surface in accordance with the installation instructions.

Never place the equipment in an unstable location. The

equipment may fall, causing serious personal injury or death. If the

device needs to be wired by yourself, select the corresponding

wire to supply power according to the electric parameters labeled

on the device. Strip off wire with a standard wire stripper at

corresponding position. To avoid serious consequences, the length

according to IEC 60950-1 or IEC 62368-1 standard.

Device powered by AC mains supply voltage: The equipment must

be connected to an earthed mains socket-outlet. An appropriate

readily accessible disconnect device shall be incorporated external

to the equipment. An appropriate overcurrent protective device

shall be incorporated external to the equipment, not exceeding

the specification of the building. An all-pole mains switch shall be

White Light Illuminator (If supported)

Possibly hazardous optical radiation emitted from this product. DO

NOT stare at operating light source. May be harmful to the eyes.

Wear appropriate eye protection or DO NOT turn on the white

light when you assemble, install or maintain the camera.

Transportation

Keep the device in original or similar packaging while transporting

it.

System Security

The installer and user are responsible for password and security

capacitor) require regular replacement. The average lifespan

varies, so periodic checking is recommended. Contact your dealer

environments. For indoor-only device, place it in a dry and

any other bright light. Make sure the running environment meets

the requirement of the device. DO NOT place the camera in

extremely hot, cold, dusty or damp locations, and do not expose it

to high electromagnetic radiation.

Emergency

If smoke, odor, or noise arises from the device, immediately turn

off the power, unplug the power cable, and contact the service

Make sure that no reflective surface is too close to the device lens.

The IR light from the device may reflect back into the lens causing

reflection.

Conformité à la réglementation et consignes de sécurité

Lisez soigneusement toutes les informations et instructions de ce

document avant d’utiliser l’appareil et conservez-le pour toute

référence ultérieure.

consulter notre site Internet à l’adresse

autres documents (le cas échéant) accompagnant l’appareil ou