Sony XR-1300R Používateľská príručka

Kategória
Kazetové prehrávače
Typ
Používateľská príručka
2000 Sony Corporation
FM/MW/LW
Cassette
Car Stereo
XR-1300R
For installation and connections, see the supplied installation/connections
manual.
Szczegóły dotyczące instalacji i podłączeń, proszę sprawdzić w dostarczonym,
osobnym podręczniku
Informace o instalaci a zapojení naleznete v přiložené příručce Instalace /
zapojení.
Kurma ve bağlantı işlemleri için ünite beraberindeki Kurma/Bağlantılar kılavuzuna
bakınız.
П орядок установки и подключения магнитолы описан в прилагаемой
инструкции об установке/подключении.
3-044-698-41 (1)
Operating Instructions
Instrukcje Obsługi
Návod k obsluze
Kullanım kılavuzu
Руководство по эксплуатации
GB
PL
TR
CZ
RU
22
Thank you for purchasing this Sony Cassette
Player.
Welcome ! Precautions
If your car was parked in direct sunlight
resulting in a considerable rise in
temperature inside the car, allow the unit to
cool off before operating it.
If no power is being supplied to the unit,
check the connections first. If everything is in
order, check the fuse.
If no sound comes from the speakers of a
two-speaker system, set the fader control to
the centre position.
When a tape is played back for a long period,
the cassette may become warm because of
the built-in power amplifier. However, this is
not a sign of malfunction.
If you have any questions or problems
concerning your unit that are not covered in
this manual, please consult your nearest Sony
dealer.
To maintain high quality sound
If you have drink holders near your audio
equipment, be careful not to splash juice or
other soft drinks onto the car audio. Sugary
residues on this unit or cassette tapes may
contaminate the playback heads, reduce the
sound quality, or prevent sound reproduction
altogether.
Cassette cleaning kits cannot remove sugar
from the tape heads.
33
Notes on Cassettes
Cassette care
Do not touch the tape surface of a cassette, as
any dirt or dust will contaminate the heads.
Keep cassettes away from equipment with
built-in magnets such as speakers and
amplifiers, as erasure or distortion on the
recorded tape could occur.
Do not expose cassettes to direct sunlight,
extremely cold temperatures, or moisture.
Slack in the tape may cause the tape to be
caught in the machine. Before you insert the
tape, use a pencil or similar object to turn the
reel and take up any slack.
Distorted cassettes and loose labels can cause
problems when inserting or ejecting tapes.
Remove or replace loose labels.
The sound may become distorted while
playing the cassette. The cassette player head
should be cleaned after each 50 hours of use.
Slack
Cassettes longer than 90 minutes
The use of cassettes longer than 90 minutes is
not recommended except for long continuous
play. The tape used for these cassettes is very
thin and tends to stretch easily. Frequent
playing and stopping of these tapes may cause
them to become entangled in the cassette deck
mechanism.
44
Table of Contents
Location of controls ................................................. 5
Getting Started
Resetting the unit ................................................ 6
Detaching the front panel .................................. 6
How to use the menu ......................................... 6
Setting the clock .................................................. 7
Cassette Player
Listening to a tape ............................................... 7
Radio Reception during Fast-forwarding or
Rewinding of a Tape
ATA (Automatic Tuner Activation) ........ 8
Radio
Memorizing stations automatically
— Best Tuning Memory (BTM).................... 8
Memorizing only the desired stations ............. 9
Receiving the memorized stations.................... 9
RDS
Overview of the RDS function ........................ 10
Displaying the station name............................ 10
Retuning the same programme automatically
Alternative Frequencies (AF) ................ 10
Listening to traffic announcements ................ 12
Presetting the RDS stations with the AF and TA
data ................................................................ 12
Locating a station by programme type .......... 13
Setting the clock automatically ....................... 14
Other Functions
Adjusting the sound characteristics ............... 15
Changing the sound and display settings ..... 15
Boosting the bass sound
— D-bass ....................................................... 16
Additional Information
Maintenance....................................................... 16
Dismounting the unit ....................................... 17
Specifications ..................................................... 18
Troubleshooting guide ..................................... 19
55
Location of controls
Refer to the pages listed for details.
1 MENU button
7, 8, 9, 11, 13, 14, 15
2 Volume control dial
3 TUNER button 8, 9, 12
4 PRST +/– (cursor up/down) buttons
7, 8, 9, 11, 13, 14, 15
During radio reception:
Preset stations select 8, 9
5 DSPL/PTY (display mode change/
programme type) button 14
6 MODE button
During radio reception:
BAND select 8, 9
7 Z (eject) button 7
8 Display window
9 m/M (fast winding)/DIR (tape
transport direction change) buttons 7
q; D-BASS button 16
qa TA button 12, 13
qs SOUND button 15
qd RELEASE (front panel release) button
6, 17
qf SEEK –/+ (cursor left/right) buttons
7, 8, 9, 11, 13, 14, 15
seek 9
qg Reset button (located on the front side
of the unit behind the front panel) 6
qh ENTER button 7, 8, 9, 11, 13, 14, 15
qj Preset number buttons 9, 11
qk OFF button* 6
ql AF button 10, 11, 13
* Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
XR-1300R
P
R
S
T
+
S
E
E
K
S
E
E
K
+
P
R
S
T
MODE
OFF
DIR
D-BASS
ENTER
MENU
SOUND
RELEASE
1 2 3 4 56
TA
AF
TUNER
DSPL
PTY
66
Getting Started
Resetting the unit
Before operating the unit for the first time or
after replacing the car battery, you must reset
the unit.
Remove the front panel and press the reset
button with a pointed object, such as a
ballpoint pen.
Note
Pressing the reset button will erase the clock
setting and some memorized functions.
Detaching the front panel
You can detach the front panel of this unit to
protect the unit from being stolen.
1 Press (OFF).
2 Press (RELEASE), then slide the front
panel a little to the left, and pull it off
towards you.
Notes
• Be sure not to drop the panel when detaching it
from the unit.
If you detach the panel while the unit is still
turned on, the power will turn off automatically
to prevent the speakers from being damaged.
When carrying the front panel with you, use the
supplied front panel case.
Reset button
(OFF)
(RELEASE)
A
B
TUNER
Attaching the front panel
Attach part A of the front panel to part B of
the unit as illustrated and push the left side
into position until it clicks.
Notes
• Be sure not to attach the front panel upside
down.
• Do not press the front panel too hard against the
unit when attaching it.
• Do not press too hard or put excessive pressure
on the display window of the front panel.
• Do not expose the front panel to direct sunlight
or heat sources such as hot air ducts, and do not
leave it in a humid place. Never leave it on the
dashboard of a car parked in direct sunlight or
where there may be a considerable rise in
temperature.
Caution alarm
If you turn the car ignition off without
removing the front panel, the caution alarm
will beep for a few seconds.
If you connect an optional power amplifier and
do not use the built-in amplifier, the beep
sound will be deactivated.
How to use the menu
This unit is operated by selecting items from a
menu.
To select, first enter the menu mode and
choose up/down (+/ of (PRST)), or choose
left/right (/+ of (SEEK)).
(PRST)
(+) : To select upwards
() : To select downwards
77
Cassette Player
Listening to a tape
Insert a cassette.
Playback starts automatically.
The side facing up is played.
The side facing down is played.
Tip
To change the tape‘s playback direction, press m
and M.
To stop playback and eject the
cassette
Press Z.
Fast-winding the tape
During playback, press m or M.
* The < > indicator will flash while fast-winding
the tape.
To start playback during fast-forwarding or
rewinding, press the other fast-winding button
partially until the locked button is released.
To rewind
m
M
Direction
indicator*
FWD
REV
To advance
M
m
(SEEK)
Setting the clock
The clock uses a 24-hour digital indication.
Example: To set the clock to 10:08
1 Press (MENU), then press either side of
(PRST) repeatedly until CLOCK
appears.
1 Press (ENTER).
The hour indication flashes.
2 Press either side of (PRST) to set the
hour.
3 Press + side of (SEEK).
The minute indication flashes.
4 Press either side of (PRST) to set the
minute.
2 Press (ENTER).
The clock starts.
After the clock setting is complete, the
display returns to normal playback mode.
TUNER
() : To select
leftwards
(+) : To select
rightwards
88
Radio
Memorizing stations
automatically
— Best Tuning Memory (BTM)
The unit selects the stations with the strongest
signals and memorizes them in the order of
their frequencies. You can store up to 6 stations
on each band (FM1, FM2, FM3, MW, and LW).
Caution
When tuning in stations while driving, use
Best Tuning Memory to prevent accidents.
1 Press (TUNER).
The tuner is turned on.
2 Press (MODE) repeatedly to select the
band.
Each time you press (MODE), the band
changes as follows:
B FM1 B FM2 B FM3 B MW B LW
3 Press (MENU), then press either side of
(PRST) repeatedly until BTM appears.
4 Press (ENTER).
The unit stores stations in the order of their
frequencies on the number buttons.
A beep sounds when the setting is stored.
Notes
• The unit does not store stations with weak
signals. If only a few stations can be received,
some number buttons will retain their former
setting.
• When a number is indicated in the display, the
unit starts storing stations from the one currently
displayed.
Radio Reception during
Fast-forwarding or
Rewinding of a Tape
— ATA (Automatic Tuner Activation)
When fast-forwarding or rewinding with the
m or M button, the tuner will turn on
automatically.
1 During playback, press (MENU).
2 Press either side of (PRST) repeatedly
until ATA appears.
3 Press + side of (SEEK) to select ON.
Play mode starts.
4 Press (ENTER).
To return to normal playback mode, select
OFF in step 3 above.
99
Memorizing only the
desired stations
You can preset up to 18 FM stations (6 each for
FM1, 2, and 3), up to 6 MW stations, and up to
6 LW stations in the order of your choice.
1 Press (TUNER).
The tuner is turned on.
2 Press (MODE) repeatedly to select the
band.
3 Press either side of (SEEK) to tune in the
station that you want to store on the
number button.
4 Press and hold the desired number
button ((1) to (6)) until MEM appears.
The number button indication appears in
the display.
Note
If you try to store another station on the same
number button, the previously stored station will
be erased.
Receiving the memorized
stations
1 Press (TUNER).
The tuner is turned on.
2 Press (MODE) repeatedly to select the
band.
3 Press the number button ((1) to (6)) on
which the desired station is stored.
Tip
Press either side of (PRST) to receive the stations
in the order they are stored in the memory (Preset
Search Function).
If you cannot tune in a preset
station
Press either side of (SEEK) to search for
the station (automatic tuning).
Scanning stops when the unit receives a
station. Press either side of (SEEK)
repeatedly until the desired station is
received.
Note
If the automatic tuning stops too frequently, press
(MENU), then press either side of (PRST)
repeatedly until “LOCAL” (local seek mode) is
displayed. Then press + side of (SEEK) to select
“LOCAL-ON.” Press (ENTER).
Only the stations with relatively strong signals will
be tuned in.
Tip
If you know the frequency of the station you want
to listen to, press and hold either side of (SEEK)
until the desired frequency appears (manual
tuning).
If FM stereo reception is poor
— Monaural Mode
1 During radio reception, press (MENU),
then press either side of (PRST)
repeatedly until MONO appears.
2 Press + side of (SEEK) until MONO-ON
appears.
The sound improves, but becomes
monaural (ST disappears).
3 Press (ENTER).
To return to normal mode, select MONO-
OFF in step 2 above.
10
Retuning the same
programme automatically
Alternative Frequencies (AF)
The Alternative Frequencies (AF) function
automatically selects and retunes the station
with the strongest signal in a network. By
using this function, you can continuously
listen to the same programme during a long-
distance drive without having to retune the
station manually.
1 Select an FM station (page 9).
2 Press (AF) repeatedly until AF-ON
appears.
The unit starts searching for an alternative
station with a stronger signal in the same
network.
Note
When there is no alternative station in the area
and you do not need to search for an alternative
station, turn the AF function off by pressing (AF)
repeatedly until AF-OFF appears.
102.5MHz
96.0MHz
98.5MHz
Frequencies change automatically.
Station
RDS
Overview of the RDS
function
Radio Data System (RDS) is a broadcasting
service that allows FM stations to send
additional digital information along with the
regular radio programme signal. Your car
stereo offers you a variety of services. Here are
just a few: retuning the same programme
automatically, listening to traffic
announcements, and locating a station by
programme type.
Notes
Depending on the country or region, not all of
the RDS functions are available.
RDS may not work properly if the signal strength
is weak or if the station you are tuned to is not
transmitting RDS data.
Displaying the station
name
The name of the current station lights up in the
display.
Select an FM station (page 9).
When you tune in an FM station that
transmits RDS data, the station name
appears in the display.
Note
The * indication means that an RDS station is
being received.
11
Local link function
(United Kingdom only)
The Local Link function lets you select other
local stations in the area, even if they are not
stored on your number buttons.
1 Press a number button that has a local
station stored on it.
2 Within five seconds, press the number
button of the local station again.
3 Repeat this procedure until the desired
local station is received.
Changing the display item
Each time you press (AF), the item changes as
follows:
AF-ON y AF-OFF
Notes
When NO AF and the station name flash
alternately, it means that the unit cannot find an
alternative station in the network.
If the station name starts flashing after selecting
a station with the AF function on, this indicates
that no alternative frequency is available. Press
either side of (SEEK) while the station name is
flashing (within eight seconds). The unit starts
searching for another frequency with the same PI
(Programme Identification) data (PI SEEK
appears and no sound is heard). If the unit
cannot find another frequency, NO PI appears,
and the unit returns to the previously selected
frequency.
Listening to a regional programme
The REG-ON (regional on) function lets you
stay tuned to a regional programme without
being switched to another regional station.
(Note that you must turn the AF function on.)
The unit is factory preset to REG-ON, but if
you want to turn off the function, do the
following.
1 During radio reception, press (MENU),
then press either side of (PRST)
repeatedly until REG appears.
2 Press + side of (SEEK) until REG-OFF
appears.
3 Press (ENTER).
Note that selecting REG-OFF might cause
the unit to switch to another regional
station within the same network.
To return to regional on, select REG-ON in
step 2 above.
Note
This function does not work in the United
Kingdom and in some other areas.
12
Presetting the volume of traffic
announcements
You can preset the volume level of the traffic
announcements beforehand so you wont
miss the announcement. When a traffic
announcement starts, the volume will be
automatically adjusted to the preset level.
1 Select the desired volume level.
2 Press (TA) for two seconds.
TA appears and the setting is stored.
Receiving emergency
announcements
If an emergency announcement comes in while
you are listening to the radio, the programme
will automatically switch to it. If you are
listening to a source other than the radio, the
emergency announcements will be heard if
you set AF or TA to on. The unit will then
automatically switch to these announcements
no matter which source you are listening to at
the time.
Presetting the RDS
stations with the AF and
TA data
When you preset RDS stations, the unit stores
each stations data as well as its frequency, so
you dont have to turn on the AF or TA
function every time you tune in the preset
station. You can select a different setting (AF,
TA, or both) for individual preset stations, or
the same setting for all preset stations.
Listening to traffic
announcements
The Traffic Announcement (TA) and Traffic
Programme (TP) data let you automatically
tune in an FM station that is broadcasting
traffic announcements even if you are listening
to other programme sources.
Press (TA) repeatedly until TA-ON
appears.
The unit starts searching for traffic
information stations. TP appears in the
display when the unit finds a station
broadcasting traffic announcements.
When the traffic announcement starts,
TA flashes. The flashing stops when the
traffic announcement is over.
Tip
If the traffic announcement starts while you are
listening to another programme source, the unit
automatically switches to the announcement and
goes back to the original source when the
announcement is over.
Notes
NO TP flashes for five seconds if the received
station does not broadcast traffic announcements.
Then, the unit starts searching for a station that
broadcasts it.
When EON appears with TP in the display,
the current station makes use of broadcast traffic
announcements by other stations in the same
network.
To cancel the current traffic
announcement
Press (TA) or (TUNER).
To cancel all traffic announcements, turn off
the function by pressing (TA) until
TA-OFF appears.
13
Presetting the same setting for all
preset stations
1 Select an FM band (page 9).
2 Press (AF) or/and (TA) to select AF-ON
or/and TA-ON.
Note that selecting AF-OFF or TA-OFF
stores not only RDS stations, but also non-
RDS stations.
3 Press (MENU), then press either side of
(PRST) repeatedly until BTM appears.
4 Press + side of (SEEK) until BTM
flashes.
5 Press (ENTER).
Presetting different settings for
each preset station
1 Select an FM band, and tune in the
desired station.
2 Press (AF) or/and (TA) to select AF-ON
or/and TA-ON.
3 Press the desired number button and
hold until MEM appears.
Repeat from step 1 to preset other stations.
Tip
If you want to change the preset AF and/or TA
setting after you tune in the preset station, you
can do so by turning the AF or TA function on or
off.
Locating a station by
programme type
You can locate the station you want by
selecting one of the programme types shown
below.
Programme types Display
News NEWS
Current Affairs AFFAIRS
Information INFO
Sports SPORT
Education EDUCATE
Drama DRAMA
Culture CULTURE
Science SCIENCE
Varied VARIED
Popular Music POP M
Rock Music ROCK M
Easy Listening EASY M
Light Classical LIGHT M
Classical CLASSICS
Other Music Type OTHER M
Weather WEATHER
Finance FINANCE
Childrens Programmes CHILDREN
Social Affairs SOCIAL A
Religion RELIGION
Phone In PHONE IN
Travel TRAVEL
Leisure LEISURE
Jazz Music JAZZ
Country Music COUNTRY
National Music NATION M
Oldies Music OLDIES
Folk Music FOLK M
Documentary DOCUMENT
Not specified NONE
Note
You cannot use this function in some countries
where no PTY (Programme Type selection) data is
available.
14
1 Press (DSPL/PTY) during FM reception
until PTY appears.
The current programme type name appears
if the station is transmitting the PTY data.
- - - - - appears if the received station is
not an RDS station, or if the RDS data has
not been received.
If the TA function is ON, the unit starts
searching for the next station.
2 Press (PRST) repeatedly until the desired
programme type appears.
The programme types appear in the order
shown in the above table. Note that you
cannot select NONE (Not specified) for
searching.
3 Press (ENTER) repeatedly until the
desired station is received.
The unit starts searching for a station
broadcasting the selected programme type.
When the unit finds the programme, the
programme type appears again for five
seconds.
NO and the programme type appear
alternately for five seconds if the unit
cannot find the programme type. It then
returns to the previously selected station.
Setting the clock
automatically
The CT (Clock Time) data from the RDS
transmission sets the clock automatically.
1 During radio reception, press (MENU),
then press either side of (PRST)
repeatedly until CT appears.
2 Press + side of (SEEK) repeatedly until
CT-ON appears.
The clock is set.
3 Press (ENTER) to return to the normal
display.
To cancel the CT function
Select CT-OFF in step 2 above.
Notes
The CT function may not work even though an
RDS station is being received.
There might be a difference between the time
set by the CT function and the actual time.
15
Changing the sound and
display settings
The following items can be set:
CLOCK (page 7).
CT (Clock Time) (page 14).
BEEP to turn the beep sound on or off.
D.INFO (Dual Information) to display the
clock and the play mode at the same time
(ON) or to display the information
alternately (OFF).
M.DSPL (Motion Display) to turn the
motion display on or off.
1 Press (MENU).
2 Press either side of (PRST) repeatedly
until the desired item appears.
Each time you press () side of (PRST), the
item changes as follows:
CLOCK t CT t BEEP t D.INFO t M.DSPL
3 Press (+) side of (SEEK) to select the
desired setting (Example: ON or OFF).
4 Press (ENTER).
After the mode setting is complete, the
display returns to normal playback mode.
Other Functions
Adjusting the sound
characteristics
You can adjust the bass, treble, balance, and
fader.
You can store the bass and treble levels
independently for each source.
1 Select the item you want to adjust by
pressing (SOUND) repeatedly.
BAS (bass) t TRE (treble) t
BAL (left-right) t FAD (front-rear)
2 Adjust the selected item by pressing
either side of (SEEK).
Adjust within three seconds after selecting
the item.
16
0dB
D.BASS-3
D.BASS-2
D.BASS-1
D.BASS-3
D.BASS-2
D.BASS-1
Boosting the bass sound
D-bass
You can enjoy a clear and powerful bass
sound. The D-bass function boosts the low
frequency signal and high frequency signal
with a sharper curve than conventional bass
boost.
You can hear the bass line more clearly even
while the vocal volume remains the same. You
can emphasize and adjust the bass sound
easily with the D-BASS control.
Adjusting the bass curve
Press (D-BASS) repeatedly to select the
desired bass curve.
As the D-BASS number increases so does
the effect.
D.BASS-1 t D.BASS-2 t D.BASS-3 t
D.BASS-OFF
Note
The bass sound may distort at same volume. If the
bass sound distorts, select less effective bass curve.
Level
Frequency (Hz)
Fuse (10 A)
Additional
Information
Maintenance
Fuse replacement
When replacing the fuse, be sure to use one
matching the amperage rating stated on the
original fuse. If the fuse blows, check the
power connection and replace the fuse. If the
fuse blows again after replacement, there may
be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Warning
Never use a fuse with an amperage rating
exceeding the one supplied with the unit as
this could damage the unit.
17
Release key (supplied)
Dismounting the unit
1
2
3
4
Cleaning the connectors
The unit may not function properly if the
connectors between the unit and the front
panel are not clean. In order to prevent this,
open the front panel by pressing (RELEASE),
then detach it and clean the connectors with a
cotton swab dipped in alcohol. Do not apply
too much force. Otherwise, the connectors may
be damaged.
Main unit
Back of the front panel
Notes
For safety, turn off the engine before cleaning
the connectors and remove the key from the
ignition switch.
Never touch the connectors directly with your
fingers or any metal device.
18
Specifications
Cassette player section
Tape track 4-track 2-channel stereo
Wow and flutter 0.13 % (WRMS)
Frequency response 30 15,000 Hz
Signal-to-noise ratio 55 dB
Tuner section
FM
Tuning range 87.5 108.0 MHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz
Usable sensitivity 9 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 65 dB (stereo),
68 dB (mono)
Harmonic distortion at 1 kHz
0.7 % (stereo),
0.4 % (mono)
Separation 35 dB at 1 kHz
Frequency response 30 15,000 Hz
MW/LW
Tuning range MW: 531 1,602 kHz
LW: 153 279 kHz
Aerial terminal External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity MW: 30 µV
LW: 50 µV
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 8 ohms
Maximum power output 45 W × 4 (at 4 ohms)
General
Outputs Power aerial relay control
lead
Power amplifier control
lead
Tone controls Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
Power requirements 12 V DC car battery
(negative earth)
Dimensions Approx. 188 × 58 × 182 mm
(w/h/d)
Mounting dimensions Approx. 182 × 53 × 163 mm
(w/h/d)
Mass Approx. 1.2 kg
Supplied accessories Parts for installation and
connections (1 set)
Front panel case (1)
Design and specifications are subject to change
without notice.
19
Troubleshooting guide
The following checklist will help you remedy the problems you may encounter with your unit.
Before going through the checklist below, check the connections and operating procedures.
General
Tape playback
Problem
The sound is distorted.
Cause/Solution
The tape head is contaminated.
t Clean the head with a commercially available dry-type
cleaning cassette.
Radio reception
Problem
Preset tuning is not possible.
Automatic tuning is not
possible.
The stations cannot be
received.
The sound is hampered by
noises.
The ST indication flashes.
Cause/Solution
Memorize the correct frequency.
The broadcast signal is too weak.
The broadcast signal is too weak.
t Use manual tuning.
Connect an power aerial control lead (blue) or accessory power
supply lead (red) to the power supply lead of a cars aerial
booster. (When your car has built-in FM/MW/LW aerial in the
rear/side glass only.)
Tune in the frequency accurately.
The broadcast signal is too weak.
t Set to MONO mode (page 9).
Problem
No sound.
The contents of the memory
have been erased.
Indications do not appear
in the display.
Cause/Solution
Set the fader control to the centre position for two-speaker
systems.
Rotate the dial clockwise to adjust the volume.
The power cord or battery has been disconnected.
The reset button was pressed.
t Store again into the memory.
Remove the front panel and clean the connectors. See
Cleaning the connectors (page 17) for details.
Continued to next page t
20
RDS
Problem
The SEEK starts after a few
seconds of listening.
No traffic announcements.
PTY displays NONE.
Cause/Solution
The station is non-TP or has a weak signal.
t Press (AF) or (TA) repeatedly until AF-OFF or
TA-OFF appears.
Activate TA.
The station does not broadcast any traffic announcements
despite being TP.
t Tune to another station.
The station does not specify the programme type.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Sony XR-1300R Používateľská príručka

Kategória
Kazetové prehrávače
Typ
Používateľská príručka