Hitachi CR 18DGL Handling Instructions Manual

Značka: Hitachi

Model: CR 18DGL

Kategória: Elektrické náradie

Typ: Handling Instructions Manual

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Pokyny na manipuláciu

Инструкция за експлоатация

Uputstvo za rukovanje

Upute za rukovanje

Iнструкції щодо поводження з

пристроєм

Инструкция по эксплуатации

CR 18DGL

ﬁ

English

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power toolʼs operation.

If damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another

battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ position before connecting to

power source and/or battery pack, picking up or

carrying the tool.

(Original instructions)

English

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

CORDLESS RECIPROCATING SAW

SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Preparing and checking the work environment. Make

sure that the work site meets all the conditions laid forth

in the precautions.

2. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

3. Never disassemble the rechargeable battery and

charger.

4. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

5. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

6. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

7. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

8. When using this unit continuously, the unit may overheat,

leading to damage in the motor and switch. Therefore,

whenever the housing becomes hot, give the saw a

break for a while.

9. If the machine is used continuously at low speed, an

extra load is applied to the motor which can result in

motor seizure. Always operate the power tool so that

the blade is not caught by the material during operation.

Always adjust the blade speed to enable smooth cutting.

10. Always hold the body handle and front cover of the

power tool ﬁ rmly. Otherwise the counterforce produced

may result in inaccurate and even dangerous operation.

11. Mounting and dismounting the blade

○ Pull the back of the saw blade two or three times by hand

and check that the blade is securely mounted. When

pulling the blade, you will know it is properly mounted if it

clicks and the lever moves slightly. (Fig. 2)

○ When pulling the saw blade, be absolutely sure to pull it

from the back. Pulling other parts of the blade will result

in an injury.

○ If the broken saw blade is hidden inside the small slit,

hook the broken blade using a tip of another saw blade

and take it out. (Fig. 3)

○ After use, blow away sawdust, earth, sand, moisture,

etc., with air or brush them away with a brush, etc., to

ensure that the blade mount can function smoothly.

○ Do not use any saw blade with a worn-out blade hole.

Otherwise, the saw blade can come oﬀ , resulting in

personal injury.

12. Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

13. Do not ﬁ x and secure the switch lock. Besides, keep

your ﬁ nger oﬀ the switch trigger when the circular saw is

being carried around. Otherwise, the main body switch

can be inadvertently turned ON, resulting in unexpected

accidents.

14. Be careful not to let sawdust, earth, moisture, etc., enter

the inside of the machine through the plunger section

during operation. If sawdust and the like accumulate in

the plunger section, always clean it before use.

15. Do not remove the front cover which will cause in an

injury.

Be sure to hold the body from the top of the front cover.

16. During use, press the base ﬁ rmly against the workpiece.

17. Select a saw blade of the most appropriate length.

Ideally, the length protruding from the base of the saw

blade after su

btracting the stroke quantity should be

larger than the material.

If you cut a large pipe, large block of wood, etc., that

exceeds the cutting capacity of a blade; there is a risk

that the blade may contact with the inner wall of the pipe,

wood, etc., resulting in damage. (Fig. 4)

18. Never apply any unreasonable force to the saw blade

when cutting. Doing so can easily break the blade.

19. The motor can be locked sometimes, depending

on the combination of the material to be cut and the

blade. Whenever the motor gets locked, switch it oﬀ

immediately.

20. Use clamps or another practical way to secure and

support the workpiece to a stable platform. (Fig. 5)

Holding the work by hand or against your body leaves it

unstable and may lead to loss of control.

21. When cutting metallic materials, use an appropriate

cutting ﬂ uid (spindle oil, soapy water, etc.) to prolong the

bladeʼs service life.

22. Delay the feed speed when cutting the material into

small circular arcs. An unreasonably fast feed may break

the blade.

23. Plunge cutting

○ Avoid plunge cutting for metallic materials. This can

easily damage the blade.

○ Never pull the switch trigger while the tip of the saw

blade tip is pressed against the material. If you do so, the

blade can easily be damaged when it collides with the

material.

○ Make absolutely sure that you cut slowly while holding

the body ﬁ rmly. If you apply any unreasonable force to

the saw blade during the cutting operation, the blade can

easily be damaged.

24. Keep the light ON during cutting operation only. If

it is lit ON in other cases, the main body switch can

be inadvertently turned ON, resulting in unexpected

accidents.

English

25. Do not expose directly your eye to the light by looking

into the light.

If your eye is continuously exposed to the light, your eye

will be hurt.

26. Never touch moving parts.

Never place your hands, ﬁ ngers or other body parts near

the tool’s moving parts.

27. Never operate without all guards in place.

Never operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard or

safety feature before resuming operation of the tool.

28. NEVER leave tool running unattended. Turn power oﬀ .

Don’t leave tool until it comes to a complete stop.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately stop

further recharging.

8. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium

ion battery, the battery may be shorted, causing ﬁ re. When

storing the lithium ion battery, obey surely the rules of

following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe the

following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100Wh are considered to be in the freight classiﬁ cation

of Dangerous Goods and will require special application

procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

Power Output

2 to 3 digit number

English

NAMES OF PARTS (Fig. 1 – Fig. 10)

Handle

Switch trigger

Lock-oﬀ button

Housing

Front cover

Lever

Blade

Base

LED light

Base lever

Battery (optional accessories)

Blade hole

Slit of plunger

Another blade

Stroke

SYMBOLS

WARNING

The following show symbols used for the machine. Be

sure that you understand their meaning before use.

CR18DGL:

Cordless Reciprocating Saw

Read all safety warnings and all instructions.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive 2002/96/

EC on waste electrical and electronic equipment

and its implementation in accordance with

national law, electric tools that have reached

the end of their life must be collected separately

and returned to an environmentally compatible

recycling facility.

V Rated voltage

No-load speed

Switching ON

Switching OFF

Disconnect the battery

Prohibited action

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed on page 179.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Cutting metal and stainless steel pipe.

○ Cutting various lumber.

○ Cutting mild steel, aluminum and copper plate.

○ Cutting synthetic resins, such as phenol resin and vinyl

chloride.

SPECIFICATIONS

Model CR18DGL

Voltage 18 V

No-Load Speed 0 – 3300 min

–1

Stroke 25 mm

Capacity

Steel Pipe O.D. 48 mm

Wood 100 mm

Weight* 3.0 kg (BSL1815)

* According to EPTA-Procedure 01/2003

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

CHARGING

Battery and battery charger are not included with this

product.

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the pilot lamp will blink in red (At 1- second intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in Fig. 7.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously in

red.

When the battery becomes fully recharged, the pilot lamp

will blink in red. (At 1-second intervals) (See Table 1)

● Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or the

rechargeable battery.

English

Table 1

Indications of the pilot lamp

Pilot lamp

(red)

Before

charging

Blinks

Lights for 0.5 seconds. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

While charging Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will

commence when

battery cools)

Charging

impossible

Flickers

Lights for 0.1 seconds. Does not light for 0.1

seconds. (oﬀ for 0.1 seconds)

Malfunction in the

battery or the charger

○

Since the built-in micro computer takes about 3 seconds to

conﬁ rm that the battery being charged with charger is taken

out, wait for a minimum of 3 seconds before reinserting it

to continue charging. If the battery is reinserted within 3

seconds, the battery may not be properly charged.

○ If the pilot lamp does not blink in red (every second)

even though the charger cord is connected to the power,

it indicates that the protection circuit of the charger may

be activated.

Remove the cord or plug from the power and then

connect it again after 30 seconds or so. If this does

not cause the pilot lamp to blink in red (every second),

please take the charger to the Hitachi Authorized Service

Center.

MOUNTING AND OPERATION

Action Figure Page

Mounting the blade 2 180

When the blade is broken 3

180

Select a saw blade of the

appropriate length

4 180

Fasten a workpiece ﬁ rmly 5

180

Removing and inserting the

battery

181

Charging 7

181

Adjusting the base 8 181

Switch Operation 9

181

Plunge cutting (for wood) 10 181

Selecting accessories ― 182

SELECTION OF BLADES

To ensure maximum operating eﬃ ciency and results, it is

very important to select the appropriate blade best suited to

the type and thickness of the material to be cut.

The blade number is engraved in the vicinity of the mounting

portion of each blade. Select appropriate blades by referring

to Table 3-5.

However, do not use No. 2 – 9 with the unit.

● Regarding the temperatures and charging time of the

battery.

The temperatures and charging time will become as

shown in Table 2.

Table 2

Charger

Battery

UC18YKSL

Charging voltage V 14.4 – 18

Weight kg 0.35

Temperatures at which the battery

can be recharged

0oC – 50oC

Charging time (At 20oC) BSL1815 Approx. 40 min.

Number of battery cells 5

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

English

Table 5: Selection of blades for other materials

Material to

be cut

Material

quality

Thickness

(mm)

Blade No.

Iron plate Mild steel

plate 2.5 – 10

No. 101, 102,

103, 104, 109,

110, 131

Below 3.5 No. 107, 108

Nonferrous

metal

Aluminium,

Copper and

Brass

5 – 20

No. 101, 102,

103, 104, 109,

110, 131, 132

Below 5 No. 107, 108

Synthetic

resin

Phenol resin,

Melamine

resin, etc.

10 – 50

No. 101, 102,

103, 104, 131,

132

5 – 30

No. 107, 108,

109, 110

Vinyl chloride,

Acrylic resin,

etc.

10 – 60

No. 101, 102,

103, 104, 131,

132

5 – 30

No. 107, 108,

109, 110

MAINTENANCE AND INSPECTION

CAUTION

Be sure to turned oﬀ the switch and remove the battery

before maintenance and inspection.

1. Inspecting the blade

Continued use of a dull or damaged blade will result in

reduced cutting eﬃ ciency and may cause overloading of

the motor. Replace the blade with a new one as soon as

excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

Table 3: HCS blades

Blade

No.

Uses

Thickness

(mm)

No. 2 For cutting steel pipe less than 30

mm in diameter

2.5 – 6

No. 3 For cutting steel pipe less than 30

mm in diameter

Below 3.5

No. 4 For cutting and roughing lumber 50 – 70

No. 5 For cutting and roughing lumber Below 30

No. 8 For cutting vinyl chloride pipe less

than 100 mm in diameter

2.5 – 15

For cutting and roughing lumber Below 50

No. 9 For cutting mild steel pipe less

than 100 mm in diameter when

used with cut oﬀ guide

2.5 – 6

No. 95 For cutting stainless pipe less than

100 mm in diameter

Below 2.5

No. 96 For cutting stainless pipe less than

30 mm in diameter

Below 2.5

Table 4: Bl-METAL blades

Blade

No.

Uses

Thickness

(mm)

No. 101