Whirlpool AKR 995 IX Program Chart

Značka: Whirlpool

Model: AKR 995 IX

Kategória: Odsávače pár

Typ: Program Chart

Tento návod je vhodný aj pre

5019 318

33160



AKR 631-666-812-966

AKR 943-948-952-995-996

KARTA INSTALACYJNA

Minimalna odległość od palników: 50 cm (od palników elektrycznych), 70 cm (od palników

gazowych, olejowych lub węglowych. Jeżeli w instrukcjach instalacji kuchenki gazowej

przewidziana została większa odległość w stosunku do odległości tutaj wskazanej, należy

ją zastosować. Podczas montażu należy przestrzegać kolejności numeracji (1

.....).

Nie podłączać urządzenia do zasilania, zanim nie zostanie zakończony całkowicie jego

montaż. Uwaga! Rura odprowadzająca dym i parę oraz kolanka nie są dostarczane i należy

je zakupić oddzielnie.

POPIS INSTALACE

Minimální vzdálenost od sporáků: 50 cm (elektrické sporáky), 70 cm (sporáky na plyn, naftu

nebo uhlí). Jestliže je v pokynech k instalaci plynového spotřebiče určena větší vzdálenost,

než je uvedená vzdálenost, je nutné ji dodržet. Při montáži sledujte číslování (1

.....).

Spotřebič připojte k elektrické síti až po úplném dokončení instalace. Pozor! Nasávací

trubka a pásky k upevnění nejsou součástí vybavení, musíte je zakoupit.

INŠTALAČNÁ SCHÉMA

Minimálna vzdialenost' od sporáka: 50 cm (elektrické sporáky), 70 cm (plynové sporáky,

sporáky na naftu alebo uhlie. Ak pokyny na inštaláciu plynovej varnej dosky určujú väčšiu

vzdialenost' ako je špecifikovaná, dodržiavajte ich. Pri montáži postupujte podľa číslic

.....). Spotrebič nezapájajte do siete, kým nie je inštalácia úplne ukončená.

Upozornenie! Rúra na odvádzanie dymov a upevňovacie svorky sa nedodávajú, musíte ich

kúpit' samostatne.

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

A tűzhelytől való minimális távolság: 50 cm (elektromos tűzhely), 70 cm (gáz-, olaj- vagy

széntüzelésű tűzhely). Amennyiben a gáztűzhely üzembe helyezési útmutatója nagyobb

távolságot ír elő, úgy azt kell betartani. A felszereléshez kövesse a számozást

.....). A készüléket csak akkor szabad áram alá helyezni, ha a beüzemelés már

megtörtént. Figyelem! Az elvezető cső és a rögzítőpántok nem tartozékok, így azokat külön

meg kell vásárolni.

31833160.fm Page 1 Friday, April 1, 2005 6:48 PM

5019 318

33160

AKR 631-666-812-966

AKR 943-948-952-995-996



СХЕМА УСТАНОВКИ

Минимальное расстояние до конфорок: 50 см (электрические конфорки), 70 см

(газовые, керосиновые или угольные конфорки). Если инструкцией по установке

газовой плиты предусмотрено большее расстояние, то данное указание должно

быть выполнено. Последовательность действий при монтаже должна

соответствовать нумерации (1

.....). Не подключайте прибор к сети до

тех пор, пока его установка не будет полностью закончена. Внимание!

Выпускная труба и крепежные хомуты не входят в комплект поставки и

приобретаются отдельно.

КАРТА ЗА ИНСТАЛИРАНЕ

Минимално разстояние от печки: 50 см (електрически печки), 70 см (печки с газ,

нафта или въглища). Ако в инструкциите на устройството за готвене на газ е

указано по>голямо разстояние за тази спецификация, трябва да се изпълнява

това разстояние. За монтаж следвайте номерацията (1

.....). Не

включвайте захранването на уреда, докато инсталирането не е завършено

докрай. Внимание! Тръбата за отвеждане не е предоставена и трябва да се

закупи отделно.

FIȘA DE INSTALARE

Distanţa minimă de la arzătoare: 50 cm (arzătoare electrice), 70 cm (arzătoare pe bază de

gaze, petrol sau cărbune). Dacă instrucţiunile de instalare ale mașinii de gătit cu gaz

specifică o distanţă mai mare decât cea indicată, trebuie să ţineţi cont de ea. Pentru montaj

urmaţi numerotarea (1

.....). Nu branșaţi aparatul la curent până când nu terminaţi

definitiv operaţia de instalare. Atenţie! Tubul de evacuare și manșoanele de fixare nu fac

parte din dotare și trebuie să fie cumpărate separat.

INSTALLATION DATA SHEET

Minimum height above cooker: 50 cm (electric cookers), 70 cm (gas, gas oil or coal

cookers). If the installation instructions for a gas cooker specify a greater distance,

then this distance must be observed. To install, follow steps (1

.....). Do not

connect the hood to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought

separately.

RUS

31833160.fm Page 2 Friday, April 1, 2005 6:48 PM

5019 318

33160



AKR 631-666-812-966

AKR 943-948-952-995-996

31833160.fm Page 3 Friday, April 1, 2005 6:48 PM

5019 318

33160

AKR 631-666-812-966

AKR 943-948-952-995-996



Remove the perimeter extraction panel (if relevant) and the grease filter/s.

Pre-assemble the steam deflector on the motor assembly (if relevant): (

) fit the steam deflector to the rails of

the motor assembly (remove the two travel stop screws from the steam deflector if necessary), (

) connect

up the control panel and the lamps, (

) fix in place with the 14 screws (max).

Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood.

Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-

line drawn on the wall. The template's bottom edge represents the bottom edge of the hood.

Place the mounting bracket over the drilling template so that it matches the outlined rectangle. Mark and

drill the two outside holes. Remove the drilling template. Insert two wall plugs in the holes and fix the hood

mounting bracket in place with two 5 x 45 mm screws.

Hang the hood on the mounting bracket. Adjust gap (

) and the horizontal alignment (

) of the hood.

Remove the hood from the bracket. Drill the holes (

- Ø 8 mm - see step

). Insert two wall plugs (

10.

Apply the flue mounting bracket

to the wall against the ceiling. (Align the small slot in the bracket with

the centre-line drawn on the wall. See step

Fix the bracket in place with two wall plugs (Ø 8 mm) and

2 screws

Hang the hood on the bottom mounting bracket. (

14.

) Fix the hood to the wall with two 5 x 45 mm screws

(ABSOLUTELY NECESSARY). Plug the two holes if they are visible from the outside.

Connect an exhaust pipe to the to the collar

, the fumes must be ducted to the outside (extractor version)

or towards the deflector (filter version). Fix the deflector

to the flue support bracket

with 4 screws

(2 screws only for

120 cm wide

model). If the collar (bayonet coupling) is not already fitted, insert it on

the deflector

and secure it with 1 screw.

Make all necessary electrical connections.

10.

Apply the flues and fix them with 2 screws (

17a

) to the flue support

(

17b

11.

Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the

hood.

12.

(

120 cm wide

model only) fix the bottom section of the flue to the hood with 2 screws.

Re-fit the grease filter/s and, if a perimeter extraction panel is fitted, check for correct operation.

Important!

Only for model AKR 996: proceed with hob selection and manual calibration of the sensors. For

this purpose, read the paragraph on the next page “

Important - upon initial installation

”.

Control panel.

Grease filter.

Halogen bulbs.

Steam deflector.

Telescopic flue.

Perimeter extraction

panel (if fitted) and

release handle (

Sensors (only present

on some models).

INSTALLATION - ASSEMBLY INSTRUCTIONS

ROSK H RUS BGCZPL GB

31833160.fm Page 26 Friday, April 1, 2005 6:48 PM

5019 318

33160



AKR 631-666-812-966

AKR 943-948-952-995-996

Analogue control panel

Light : move the switch to the right or press the button to switch on.

Extraction speed : Move the switch to the right or press the next button to increase extraction speed

(or open the electric shutter ).

Digital control panel with sensors

The hood is fitted with a series of sensors which enable it to operate in 2 modes:

Automatic

mode

and

Manual

mode

Automatic mode:

the hood switches on automatically, depending on the ambient temperature (and heat) and

variations in this detected by the hood's sensors. See description of Button 3 function.

Manual mode:

the hood is switched on by the user.

Description of Buttons

OFF/Stand by button:

When the hood is OFF, all the controls are disabled (all LEDs are off).

When on stand-by, the hood is ready to operate in “

Manual mode

”,

LED C

lights up.

Light ON/OFF button: always works, even when the hood is OFF.

ON/OFF button “

Automatic mode

”: press to activate this mode (

LED C

and

on) the hood switches

on automatically, selecting a suitable extraction speed in accordance with the ambient temperature (and

heat) and any variations in this detected by the hood's sensors.

Press again to revert to

“Manual mode”

: LED

E switches off, LED C remains on (stand by). The hood will continue to run for a few minutes after you have finished

cooking but can be turned off by pressing buttons 1 or 3. The automatic function (LED on) stops a few minutes after

the motor has been switched off. The automatic function must be switched on every time you start cooking.

ON/OFF button for controlling intensive extraction speed in “

Manual mode

” (

LED D

switches on):

when selected, it operates for 5 minutes, after which time the hood automatically reverts to the

previously selected extraction speed.

5.-6.

Buttons for controlling extraction speed

1 - 2 - 3

in “

Manual mode

”.

Description of LEDs

Carbon filter

saturation led indicator

: this led lights up to indicate that the carbon filter needs to be

cleaned or replaced.

Important: this indicator must be activated in order for the hood to work:

to activate it, press buttons

and

at the same time -

LED B

lights up first, followed by

LED A

to indicate that the led indicator is

working.

Grease filter saturation led indicator: this led lights up to indicate that the grease filter needs to be cleaned.

“Stand by” led indicator.

Intensive speed led indicator.

“Automatic mode” led indicator.

Extraction speed 1 led indicator.

Extraction speed 2 led indicator.

Extraction speed 3 led indicator.

Reset filters indicator:

After cleaning or replacing the filters, with the hood on

Stand by

press Button

for more than 3 seconds.

Safety function:

this function is activated ONLY with the hood on stand-by, in the event of any SUDDEN,

VIOLENT increase in the temperature detected by the sensors, upon which the hood switches to “

Automatic

mode

” and, if necessary, selects a suitable extraction speed.

PRODUCT SHEET

ROSK H RUS BGCZPL GB

31833160.fm Page 27 Friday, April 1, 2005 6:48 PM

5019 318

33160

AKR 631-666-812-966

AKR 943-948-952-995-996



Important - upon initial installation:

Selecting the hob type:

to ensure accurate

“reading” by the sensors, the latter must be calibrated

to suit the type of hob as follows: with the hood OFF,

press buttons 3 and 4 at the same time until either

LED F

for gas hobs,

LED G

for induction hobs or

LED H

for electric hobs lights up.

Automatic and manual sensor calibration:

the

hood automatically “calibrates” sensor operation, but

under certain circumstances (e.g.: in the event of a

prolonged power failure or upon initial installation)

calibration can be carried out manually, with the hood

OFF, by pressing buttons

and

at the same time for

more than 3 seconds, otherwise you can wait until the

hood carries out calibration automatically.

Maintenance

ALWAYS disconnect the hood from the mains before

performing maintenance.

Wash the

grease filter

and the

carbon filter

in a

dishwasher once a month, at the highest possible

temperature, using normal dishwasher detergent. It is

recommended to wash the filters on the their own.

After washing, reactivate

the carbon filter

by drying

it in the oven at 100 °C for 10 minutes. Fit a new

carbon filter every 3 years.

Remove the grease filters - Fig. 1:

push the spring

release handle backwards (

) then remove the filter

downwards (

Clean the perimeter extraction panel

(if provided) as often as the grease filter

, using a

cloth and a mild liquid detergent.

Never use abrasive substances.

Clean the sensor plate regularly.

Replacing bulbs

Use a small screwdriver or any other suitable tool

to prise off (

m-Fig. 1

) the lamp cover (

p-Fig.1

Remove the burnt-out bulb.

Use max 20 W halogen bulbs only, taking care not

to touch them with your hands.

Close the lighting unit (snap-on).

Fitting the carbon filter:

Remove the grease filter (

f1/f2 - Fig. 1

Remove the filter holder by turning the knobs

(

g - Fig. 2

) through.

Fit the carbon filter (

i - Fig. 2

) in the filter holder

(

h - Fig.2

Reverse the above procedure to re-fit the filter holder

and grease filter.

Fig. 2

* Only present on some models

Fig. 1

ROSK H RUS BGCZPL GB

31833160.fm Page 28 Friday, April 1, 2005 6:48 PM

Whirlpool AKR 995 IX Program Chart

Značka: Whirlpool

Model: AKR 995 IX

Kategória: Odsávače pár

Typ: Program Chart

Tento návod je vhodný aj pre

Stiahnite si PDF

správa

v iných jazykoch

English: Whirlpool AKR 995 IX
română: Whirlpool AKR 995 IX

Súvisiace články

Ostatné dokumenty

IKEA HOO 600 S Program Chart