Foscam NVR Kit Používateľská príručka

NVR Kit

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

The user manual for the product contains the product functions, method of use and

operating procedure. Read the user manual carefully to get the best experience and

avoid unnecessary damage. Keep the manual for future reference.

NOTICE

Do not use the product in violation of local laws and regulations. A user who violates

local laws and regulations will be held responsible for all consequences of purchasing

and using the product.

Alza.cz a.s. is not responsible for any violation of local laws and regulations by the user.

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully

before first use and keep this user manual for future reference. Pay particular attention

to the safety instructions. If you have any questions or comments about the device,

please contact the customer line.

✉ www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

3

Security Tips

• Do not install the wireless NVR in humid and dusty environment.

• Put the wireless NVR in drafty environment in case of ventilation port being

blocked.

• Check the power supply to avoid damage because of voltage mismatch.

• Make sure the wireless NVR working within suitable temperature and humidity

environment.

• Please install the wireless NVR horizontally, and avoid vibration.

• Short circuit may occur when dust become wet on circuit board. Please clean the

dust on circuit board, connectors, and NVR case.

• Explosion may happen because of improper replacement of battery, do not

replace it by yourself; If you need, make sure it is the same type of battery. And

do not open or repair it.

• Please use suitable and professional hard disk to ensure continues and stable

recording.

• Lightning protection is needed when device is connected to communication

cables. Ethernet cable which comes from outside, connecting to the wireless NVR

directly is forbidden.

NVR Kit Contents

8-Channel NVR

4 x 1080P Bullet IP Cameras

4 x Power Adapters for Cameras

Quick Setup Guide

USB Mouse

1.5m (5 ft) Ethernet Cable

1 x Power Adapter for NVR

Warranty Card

Mounting Screws

4

NVR Rear Panel

Wireless Connectivity

Antenna

VGA Output

Reset

GND

Ethernet Port

HD-OUT

Power Input

(DC12V/2A)

USB

Power Switch

Computer

Router

Ethernet Cable

HD-OUT Cable

Monitor

VGA Cable

5

Placement of Wireless IP Camera

Right placement

Wrong placement

The shape of wireless NVR signal coverage is a ball, antenna is located in the center.

Signal is strong around antenna, and weak in the dent area of the 2 antennas.

Based on the signal spreading ways, please make the wireless IP Camera keeping

parallel or tangent with wireless NVR, which ensure stable signal transmission and

better picture quality.

Camera Installation

Place the cameras in your preferred locations and use the included screws to mount

them.

6

Important Note:

When installing the cameras please ensure that the connection ports at the end of the

pig tail wiring are not exposed, as they are not weather-resistant.

Powering Up

GND

DC 12V/2A

Mouse

VGA Cable

Monitor

7

Please make sure the voltage of power supply is matched with wireless NVR, and ground

connection work well in socket. Connect the NVR and cameras as shown in the gures

above. Once the NVR is plugged in, press the power switch located on the rear panel.

After the NVR starts up successfully, the Power LED indicators will turn green, it means

system runs smoothly.

Software Operation

Log In

1. Turn on the power switch on the rear panel. After the NVR starts up successfully, the

power LED and HDD LED indicators will turn green. The startup page is displayed on the

screen.

2. Change password. For your security, please set a new password for your NVR before

Log In.

8

3. Login page.

Enter the Username and Password, then click on the OK button.

4. After modifying the password, you will be taken to the Setup Wizard.

Setup Wizard

The Setup Wizard can walk you through some important settings on the NVR.

1. Setting the time.

9

2. Format HDD. Click the Format button to set up the HDD. Note that this will delete all

files on the HDD. HDD Full Setting. Select Stop Record and Overwrite.

P2P. If you want to know the UID of the device, please scan the QR code. If you don’t

want to use the Setup Wizard next time, uncheck the Setup Wizard checkbox. Click the

Finish button to complete the setup wizard.

Uncheck the checkbox

10

or Right-click→ Main Menu → Configuration → uncheck the Setup Wizard checkbox.

Click the Finish button to complete the setup wizard.

The live view interface will show you the video feed of each IP Camera.

NVR adds IP Camera method

Note: The NVR and IP Camera are already paired. If you need to match more cameras

(Only FI9910W), please refer to the following steps.

1. Right-click on main interface, select Pair IP Camera.

2. Click Pair and press the pairing button of the camera tail cable at the same time, until

it prompts that the pairing is successful.

3. When finished code matching, The live view interface will show you the video feed of

each IP Camera.

Uncheck the checkbox

11

Record and Playback

1. Scheduled Record: Right-click → Main Menu → Record → choose recording channel →

Save (Actually, the Wi-Fi NVR system have default set 24h scheduled recording).

1. Click Pair

Press the

pairing

button

12

If you want to modify it to alarm recording, please use the left mouse button to select

the time (turned to green), if the other channels operate in the same way, select copy.

13

2. Playback: Right-click → Main Menu → Playback → choose channel and date → click

timeline to check record.

Backup

Insert U disk to NVR USB port → Right-click→ Main Menu → Backup → choose channel,

type and time→ Search → select target le → Backup

Note: If target le can not be searched out, please click Empty → Add. Please remove the

files which is no need before backup. Ensure insert device (like USB) in 30 second, as

system reserved searching time for it is 30 second.

14

Motion Detection Record

Right-click → Main Menu → IPC Config → Advanced → Motion Detect → Choose

Enable → Set Sensitivity & Region & Body Filter & Body Rectangle→ Apply.

Auto Bridge

By new mesh network auto-bridging function, without any manual setting, wireless

camera in further area will have a judgment about the WIFI signal and auto connect to

the camera which have a better WIFI signal, to achieve more stable and reliable video

transmission.

Auto bridging is designed to expand the coverage area of wireless signal, instead of

enhancing the signal. When camera is a little far away from NVR, or there are too many

interference factors/sources between them, camera in further area will auto

bridge/connect to the one nearby to transmit the video data.

15

1. Right click →Pair IP Camera→ Repeater.

2. Then, bridging relationship will be showed on the interface automatically.

16

Foscam App

1. You can also simply go to the App Store or Google Play and search for the term

"Foscam". Download the APP to your smartphone, or scan the QR Code on the below, it

will take you to the download page to install the Foscam APP.

2. Run the Foscam APP, and then register for a Foscam account.

3. Device Adding: Once logged in, you can tap the "+" button on the APP, after that scan

the QR code, which is located at the bottom of your NVR.

4. Preview: click device in list to enter preview interface, select a channel to view it’s

picture, as follow shows:

17

Foscam VMS

Foscam VMS is a new tool for PC. It does not require plug-ins and is compatible with

Windows & Mac, It supports all Foscam HD cameras and up to 36 cameras at the same

time. If you would like to manage multiple cameras, we suggest you install the Foscam

VMS. You can download the “Foscam VMS” from foscam.com/vms, and can download

the "Foscam VMS" Mac version from the APP store:

https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12

Note: For the best experience, please update Foscam VMS to the latest version!

Add the NVR

1. Run Foscam VMS, then you can create a local administrator account and login.

2. Tap the "+" button on the Foscam VMS and follow the setup wizard to add your NVR.

Please refer to the user manual for more detailed adding steps.

3. Preview: click device in Lan Device list to enter preview interface, select a channel to

view it’s picture, click to enter , as follow shows:

18

Upgrade

1. You can upgrade your NVR and cameras system with local Software.

NVR Upgrade:

Download the rmware to the U disk → Insert U disk to NVR USB port → Right-click→

Main Menu → Upgrade → click Refresh → click Upgrade to upgrade your NVR.

Note: Don't shut down the power during upgrade. After upgrading, NVR restarts.

IPC Upgrade:

Download the rmware to the U disk → Insert U disk to NVR USB port → Right-click→

Main Menu → IPC Config → Maintenance → click Refresh → click CH to update this

camera or click Select All to upgrade your all cameras.

1. Click the button to select the

firmware to the U disk

2. Click the button to

Upgrade

19

Note:

1. The upgrade le must be placed under the root directory of the U disk.

2. Don't lose power for during upgrade.

You can upgrade the rmware of your NVR and cameras with Foscam App.

Open Foscam APP and Login the NVR, select Settings > NVR Firmware or Camera

Firmware Upgrade.

2.Choose the channel camera

you need to upgrade

3. Click the button to

Upgrade

1.Click the button to select

the firmware to the U disk

20

3. You can upgrade the firmware of your NVR and cameras with Foscam VMS. Open and

Login Foscam VMS, select Setup > System > System Upgrade or Camera Upgrade.

Firmware upgrade step:

1. Click "Download the latest firmware" button to download the latest firmware to

your computer.

2. Click "Browse" button , choose file firmware version you want to upgrade on the web

page.

3. Click "Upgrade" button and wait till it's finished.

Note:

In all upgrade methods, don't shut down the power during upgrade. After upgrading,

NVR restarts.

Product Performance

WLAN Frequency range:

2400MHz- 2483.5 Mhz.

Maximum transmission power:

<20dBm

Wireless Standard:

IEEE802.11b/g/n

Power Supply:

DC 12V 2.0A 24W (NVR)

DC 12V 1.0A 12W (IPC)

Stránka sa načítava...

Foscam NVR Kit Používateľská príručka

Súvisiace články

Ostatné dokumenty