Parkside PKS 1700 A1 Operation And Safety Notes Original Operating Instructions



SLIDING CROSS CUT MITRE SAW

Operation and Safety Notes

Original operating instructions

PKS 1700 A1

4



VLEČNA, ČELILNA IN ZAJERALNA ŽAGA

Navodila za upravljanje in varnostna opozorila

Originalna navodila za uporabo



BÜTÜZŐ- ÉS GÉRVÁGÓ FŰRÉSZ

Kezelési és biztonsági utalások

Eredeti használati utasítás



MULTIFUNKČNÍ PILA

Pokyny pro obsluhu a bezpečnostní pokyny

Originální návod k obsluze



DVOJRUČNÁ, SKRACOVACIA A

POKOSOVÁ PÍLA

Pokyny pre obsluhu a bezpečnostné pokyny

Originálny návod na obsluhu

  

ZUG-, KAPP- UND GEHRUNGSSÄGE

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung



PIŁA DWURĘCZNA, TARCZÓWKA, ZE

SKRĘTNĄ TARCZĄ

Wskazówki dotyczące obsługi i bezpieczeństwa

Instrukcją oryginalną

Anleitung_LB4_4300688:_ 20.12.2010 10:06 Uhr Seite 1

2

SLIDING CROSS CUT MITRE SAW



Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.



Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.



Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.



Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.



Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.



Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z

wszystkimi funkcjami urządzenia.

  

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 8

HU Kezelési és biztonsági utalások Oldal 24

SI Navodila za upravljanje in varnostna opozorila Stran 41

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 57

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 73

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 89

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 106

VLEČNA, ČELILNA IN ZAJERALNA ŽAGA

BÜTÜZŐ- ÉS GÉRVÁGÓ FŰRÉSZ

MULTIFUNKČNÍ PILA

DVOJRUČNÁ, SKRACOVACIA A

POKOSOVÁ PÍLA

ZUG-, KAPP- UND GEHRUNGSSÄGE

PIŁA DWURĘCZNA, TARCZÓWKA, ZE

SKRĘTNĄ TARCZĄ

Anleitung_LB4_4300688:_ 20.12.2010 10:06 Uhr Seite 2

3

SLIDING CROSS CUT MITRE SAW

VLEČNA, ČELILNA IN ZAJERALNA ŽAGA

BÜTÜZŐ- ÉS GÉRVÁGÓ FŰRÉSZ

MULTIFUNKČNÍ PILA

DVOJRUČNÁ, SKRACOVACIA A

POKOSOVÁ PÍLA

ZUG-, KAPP- UND GEHRUNGSSÄGE

PIŁA DWURĘCZNA, TARCZÓWKA, ZE

SKRĘTNĄ TARCZĄ

1

2 3

2

3

5

4

6

7

8

9

10

12

11

18

17

12

22

25

24

23

18

27

35

1

19

10

9

13

17

15

16 14

13

18

c

26

21

20

28

30

29

8

Anleitung_LB4_4300688:_ 20.12.2010 10:06 Uhr Seite 3

4

8

5

76

9

17

31

d

7

z

4

13

18

9

16

20

32

23

31

d

10

21

Anleitung_LB4_4300688:_ 20.12.2010 10:07 Uhr Seite 4

5

11

12

10

y

16

1

8

32

13

14

7

15

2

3

5

19

16

17

8

5

16

8

5

16

5

8

16

15

13

30

29

30

29

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 5

6

17

18

c

19

20

6

4

33

34

7

21

38

40

36

16

27

28

37

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 6

7

23

39

22

38

35

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 7

8

GB

Table of contents Page

1. Introduction .............................................................................10

2. Safety information ..................................................................10-14

3. Layout .....................................................................................14

4. Items supplied.........................................................................15

5. Intended use ..........................................................................15

6. Technical data.........................................................................16

7. Before starting the equipment .................................................16-17

8. Operation ................................................................................17-20

9. Replacing the power cable......................................................20

10. Cleaning, maintenance and ordering of spare parts................20-21

11. Disposal and recycling ............................................................21

12. Declaration of conformity ........................................................22

13. Guarantee certificate...............................................................23

The reprinting or reproduction by any other

means, in whole or in part, of documentation

and papers accompanying products is

permitted only with the express consent of ISC

GmbH.

Technical changes subject to change

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 8

9

GB

Explanation of the symbols on the equipment

“Caution - Read the operating instructions to reduce the risk of inquiry”

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Wear a breathing mask.

Dust which is injurious to health can be generated when working on wood and other

materials. Never use the device to work on any materials containing asbestos!

Wear safety goggles.

Sparks generated during working or splinters, chips and dust emitted by the device

can cause loss of sight.

Important. Risk of injury.

Never reach into the running saw blade.

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 9

10

GB

1. Introduction

 Important.

When using the equipment, a few safety

precautions must be observed to avoid injuries

and damage. Please read the complete

operating instructions and safety information

with due care. Keep this manual in a safe place

so that the information is available at all times. If

you give the equipment to any other person,

hand over these operating instructions and the

safety information as well. We cannot accept

any liability for damage or accidents which arise

due to a failure to follow these instructions and

the safety information.

2. Safety information

 CAUTION

Read all the safety information and

instructions. Any errors made in following the

safety information and instructions set out

below may result in an electric shock, fire and/or

serious injury.

Keep all the safety information and

instructions in a safe place for future use.

2.1 General safety information on electric

power tools

Important. The following safety precautions

must be taken when using electric power

tools in order to protect the user from

electric shocks and the risk of injury and

fire. Read and follow these instructions

before using the equipment.

 Keep your work area tidy

- Untidy work areas can result in accidents.

 Make allowance for ambient conditions

- Do not expose electric power tools to rain.

Never use electric power tools in damp or

wet locations. Provide good lighting. Do not

use electric power tools near flammable

liquids or gases.

 Guard against electric shock

- Avoid bodily contact with earthed parts

(e.g. pipes, radiators, cookers and

refrigerators).

 Keep children away

- Do not allow other persons to touch the

equipment or cable, keep them away from

your work area.

 Keep your electric power tools in a safe

place.

- Unused tools must be stored in a dry,

locked room out of children’s reach.

 Do not overload your tools

- It will work better and safer when used

within its quoted capacity range.

 Use the right tool

- Do not use tools or attachments too weak

for heavy duty work. Never use tools on jobs

for which they are not intended; for example,

do not use a hand-held circular saw to fell

trees or lop off branches.

 Wear suitable work clothes

- Never wear loose fitting clothes or jewelry.

They may get caught in moving parts.

Rubber gloves and non-slip shoes are

recommended when working outdoors.

Wear a hair net if you have long hair.

 Wear safety goggles.

- Use a dust mask when working on dusty

jobs.

 Do not use the cable for purposes other

than that for which it is designed.

- Do not carry the equipment by its cable

and do not use the cable to pull the plug out

of the socket. Protect the cable from heat,

oil and sharp edges.

 Secure your workpiece

- Use clamps or a vise to hold the workpiece

securely. This is safer than using your hand

and also enables you to operate the

machine with both hands.

 Do not overstretch.

- Avoid abnormal working postures. Make

sure you stand squarely and keep your

balance at all times.

 Take care of your tools

- Keep your tools sharp and clean in order to

work well and safely. Follow the

maintenance information and the

instructions for changing tools. Check the

power plug and cable on a regular basis and

have them replaced by an authorized

specialist if they are damaged. Check the

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 10

extension cable regularly and replace it if

damaged. Keep handles dry and free from

oil and grease.

 Pull the power plug

- When tools are not in use, before starting

any maintenance work or when changing

attachments such as saw blades, drill bits

and all kinds of mounted tools.

 Always remove keys and wrenches after

use

- Before switching on, make sure that all

keys and wrenches have been removed

from the tool.

 Avoid unintentional starting

- Never carry a tool with your finger on the

switch button while the tool is connected to

the power supply. Make sure that the switch

is turned off when connecting the tool to the

power supply.

 When using an extension cable

outdoors

- Check that it is approved for outdoor duty

and is marked accordingly.

 Be alert at all times

- Keep an eye on your work. Use common

sense when working. Never use the tool

when you are distracted.

 Check the equipment for damage

- Before using the tool again, check the

safety devices or any slightly damaged parts

to ensure that they are in good working

order. Check that the moving parts are

working correctly, that they do not jam, and

that no parts are damaged. Make sure that

all parts are fitted correctly to ensure that the

equipment remains safe to use. Unless

otherwise stated in the operating

instructions, damaged guards and parts

have to be repaired or replaced by a

customer service workshop. Damaged

switches have to be replaced by a customer

service workshop. Never use an electric

power tool with a switch that cannot be

turned on and off.

 Important!

- For your own safety you must only use the

accessories and additional units listed in the

operating instructions or recommended or

specified by the manufacturer. The use of

mounted tools or accessories other than

those recommended in the operating

instructions or catalog may place your

personal safety at risk.

 Repairs may only be carried out by a

qualified electrician

- This electric power tool complies with the

pertinent safety information. Repair work

must only be carried out by a trained

electrician, otherwise the equipment may

cause accidents.

 Connect up a vacuum extraction system

- If there are provisions for connecting up a

vacuum extraction system, make sure that

such a system is fitted and in use.

2.2 Special safety information on the

equipment

1. Safety precautions

 Change a worn out table insert.

 Use only blades which are recommended by

the manufacturer and comply with EN 847-

1.

 If necessary, wear suitable personal

protection equipment. This could consist of:

- Ear plugs to prevent the risk of damaging

your hearing

- A breathing mask to avoid the risk of

inhaling hazardous dust

- Always wear gloves when handling saw

blades and rough materials. Whenever

practicable, saw blades must be carried in a

container.

 The following can have an influence on dust

development:

- Worn, damaged or cracked saw blades

- Recommended capacity of the vacuum

extraction system: 20 m/s

- Proper guidance of the workpiece

 Blades made of high-alloy high-speed steel

(HSS) must not be used.

GB

11

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 11

12

GB

2. Safety information on the laser

Important:

Laser radiation

Do not look into the beam

Laser class 2

Protect yourself and your environment from

accidents by taking the appropriate

precautionary measures.

 Do not look directly into the laser beam with

the naked eye.

 Never look directly into the laser path.

 Never direct the laser beam at reflecting

surfaces, persons or animals. Even a low

output laser beam can inflict injury on the

eye.

 Caution: It is vital to follow the work

procedures described in these instructions.

Using the equipment in any other way may

result in hazardous exposure to laser

radiation.

 Never open laser module.

 When the laser is not going to be used for

an extended period of time, the batteries

should be removed.

 Never use an optical instrument (for

example magnifying glass) to view the laser

beam.

 Check the laser for damage on a regular

basis and always before use. To protect

yourself against injury, never use the

equipment if it is damaged.

 Defective lasers have to be repaired by a

customer service workshop.

3. Safety information on the batteries

 Never recharge the batteries. Danger of

explosion.

 Keep batteries out of the reach of children.

Do not throw batteries into the fire, short-

circuit or take them apart.

 If necessary clean the contacts on the

batteries and equipment before inserting the

batteries.

 Remove flat batteries immediately from the

equipment. Risk of leakage!

 Always replace all batteries in one go. Only

use new batteries of the same make.

 Avoid contact with skin, eyes and mucous

membranes. If you come into contact with

battery acid, rinse the affected pars at once

with plenty of clear water and seek

immediate medical assistance.

 Do not expose batteries to extreme

conditions, e.g. do not place on heaters or in

direct sunshine. Increased risk of leakage.

4. Maintenance and service

 The following conditions can have an

influence on noise impact on the operator:

- Type of saw blade (e.g. saw blades

designed to reduce noise development)

- Material of the workpiece

- The force with which the workpiece is

pushed against the saw blade

 Faults on the machine or its guards, safety

devices and blade must be reported to the

person in charge as soon as they are

discovered.

5. Safe operation

 Use a suitable blade for the material you

wish to saw.

 Never use the drag, crosscut and miter saw

to cut any materials other than those

specified by the manufacturer.

 Use only the transport devices to move the

equipment. Never use the guards for

handling or moving the equipment.

 Use the saw only if it is in perfect condition

and properly maintained and only if the

guards are correctly positioned.

 When cutting miters, make sure that the

device for swiveling the arm is fastened

securely.

 The floor around the machine must be level,

clean and free of loose particles, such as

chips and cutting residues.

 The operator must receive proper training in

the use, adjustment and operation of the

machine.

 Only use properly sharpened saw blades.



Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 12

Do not exceed the maximum speed

specified on the blade.

 Be sure to only use spacers and spindle

rings specified by the manufacturer as

suitable for the intended purpose.

 If the machine is equipped with a laser, this

laser may not be replaced by a different

type of laser. Repairs may only be carried

out by the manufacturer of the laser or one

of his authorized agents.

 Do not remove any cutting residues or other

parts of workpieces from the cutting zone

while the machine is running and the saw

unit is not at rest.

 Make sure that the machine is always

secured on a workbench or a table if at all

possible.

 Support long workpieces (e.g. with a roller

table) to prevent them sagging at the end of

a cut.

6. Additional safety information on

crosscut saws

 Give these safety instructions to all persons

who work on the machine.

 Do not use this saw to cut fire wood.

 Caution! Hands and fingers may be injured

on the rotating saw blade.

 Before you use the machine for the first

time, check that the voltage marked on the

rating plate is the same as your mains

voltage.

 If you need to use an extension cable, make

sure its conductor cross-section is big

enough for the saw’s power consumption.

Minimum cross-section: 1.5 mm

2

.

 If you use a cable reel, the complete cable

must be pulled off the reel.

 Operators have to be at least 18 years of

age. Trainees of at least 16 years of age are

allowed to use the machine under

supervision.

 Persons working on the machine should not

be distracted.

 Note the direction of rotation of the motor

and saw blade.

 After you have switched off the motor, never

slow down the saw blade by applying

pressure to its side.

 Only fit blades which are well sharpened

and have no cracks or deformations.

 Faulty saw blades must be replaced

immediately.

 Never use saw blades which do not comply

with the data specified in this manual.

 It is imperative to make sure that the arrow

on the saw blade conforms with the arrow

on the machine.

 Pull out the power plug and twist the blade

with your hand into the 45° and 90°

positions in order to make sure that the

blade does not touch the turntable in any

position. If necessary, readjust the saw

head.

 It is imperative to make sure that all devices

which cover the saw blade are in good

working order.

 Never wedge the hinged saw blade guard in

open position.

 Never dismantle the machine’s safety

devices or render them inoperative.

 Damaged or faulty safety devices have to

be replaced immediately.

 Never cut workpieces which are too small to

hold securely in your hand.

 Avoid placing your hands in hazardous

positions in which, one or both hands could

touch the saw blade if they slip suddenly.

 The saw must not to be used for cutting

round workpieces.

 There must be no nails or other foreign

bodies in the part of the workpiece that you

wish to saw.

 Always stand to the side of the saw blade

when working with the saw.

 Never load the machine so much that it cuts

out.

 Always press the workpiece firmly against

the workbench and the stop rail to prevent

the workpiece wobbling or twisting.

 Ensure that the off-cuts can be removed to

the side of the saw blade. Otherwise it is

possible that they will be caught by the saw

blade and catapulted out of the machine.

 Never saw more than one workpiece at any

one time.

 Never remove loose splinters, chips or

jammed pieces of wood when the saw

blade is running.

 To rectify faults or remove jammed pieces

13

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 13

of wood, always switch off the machine first.

- Pull out the power plug-

 Refit all guards and safety devices

immediately after you have completed any

repairs or maintenance work.

 Be sure to observe the safety information

and operating and maintenance instructions

issued by the manufacturer, as well as the

dimensions listed in the Technical Data.

 It is imperative to observe the accident

prevention regulations in force in your area

as well as all other generally recognized

rules of safety.

 It is imperative to observe the accident

prevention regulations in force in your area

as well as all other generally recognized

rules of safety.

 Operation in enclosed areas is permitted

only with a suitable vacuum extraction

system.

 The crosscut saw has to be connected to a

230 V socket-outlet (shock-proof socket)

with earthing contact and minimum fusing of

10 A.

 Do not use any low-powered machines for

heavy duty work.

 Be careful when working in vertical mode.

 Caution: Take extra care when making

double miter cuts!

Please keep these safety instructions in a

safe place

3. Layout

1. Handle

2. ON/OFF switch

3. Release lever

4. Saw shaft lock

5. Machine head

6. Movable blade guard

7. Saw blade

8. Clamping device

9. Workpiece support

10. Locking screw for workpiece support

11. Table insert

12. Latched position lever

13. Locking grip

14. Pointer

15. Scale

16. Turntable

17. Fixed saw table

18. Additional stability bar

19. Stop rail

20. Scale

21. Pointer

22. Sawdust bag

23. Locking screw

24. Locking screw for drag guide

25. Fastening bolt

26. Drag guide

27. Knurled screw for cutting depth limiter

28. Stop for cutting depth limiter

29. Adjustable stop rail

30. Locking lever for adjustable stop rail

31. Adjustment screw (90°)

32. Adjustment screw (45°)

33. Flange bolt

34. Outer flange

35. Laser

36. ON/OFF switch for laser

37. Battery compartment

38. Battery compartment cover

39. Screw

40. Inner flange

c) Wrench

d) Counternut

y) 45° stop angle (not supplied)

y) 90° stop angle (not supplied)

14

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 14

4. Items supplied

 Drag, crosscut and miter Saw

 2 x Clamping device (8)

 2 x Workpiece support (9)

 Sawdust bag (22)

 Allen key

 Wrench (c)

 Additional stability bar (18)

 2 x Battery (1.5 V LR6)

5. Intended use

The drag, crosscut and miter saw is designed

to crosscut wood and plastic respective of the

machine’s size. The saw is not designed for

cutting firewood.

The equipment is to be used only for its

prescribed purpose. Any other use is deemed

to be a case of misuse. The user / operator and

not the manufacturer will be liable for any

damage or injuries of any kind caused as a

result of this.

Please note that our equipment has not been

designed for use in commercial, trade or

industrial applications. Our warranty will be

voided if the equipment is used in commercial,

trade or industrial businesses or for equivalent

purposes.

The equipment is to be operated only with

suitable saw blades. It is prohibited to use any

type of cutting-off wheel.

To use the equipment properly you must also

observe the safety information, the assembly

instructions and the operating instructions to be

found in this manual.

All persons who use and service the equipment

have to be acquainted with this manual and

must be informed about the equipment’s

potential hazards. It is also imperative to

observe the accident prevention regulations in

force in your area. The same applies for the

general rules of health and safety at work.

The manufacturer will not be liable for any

changes made to the equipment nor for any

damage resulting from such changes. Even

when the equipment is used as prescribed it is

still impossible to eliminate certain residual risk

factors. The following hazards may arise in

connection with the machine’s construction and

design:

 Contact with the saw blade in the

uncovered saw zone.

 Reaching into the running saw blade (cut

injuries).

 Kick-back of workpieces and parts of

workpieces.

 Saw blade fracturing.

 Catapulting of faulty carbide tips from the

saw blade.

 Damage to hearing if ear-muffs are not used

as necessary.

 Harmful emissions of wood dust when used

in closed rooms.

 The product meets the requirements of EN

61000-3-11 and is subject to special

connection conditions. This means that use

of the product at any freely selectable

connection point is not allowed.

 Given unfavorable conditions in the power

supply the product can cause the voltage to

fluctuate temporarily.

 The product is exclusively intended for use

at connection points that have a continuous

current-carrying capacity of at least 100 A

per phase.

 As the user, you are required to ensure, in

consultation with your electric power

company if necessary, that the connection

point at which you wish to operate the

product meets the specified requirements.

15

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 15

6. Technical data

AC motor: 230V ~ 50Hz

Power: 1700 W

Operating mode: S1

Idle speed n

0

: 4,800 min

-1

Carbide saw blade: ø 210 x ø 30 x 2.8 mm

Number of teeth: 24

Swiveling range: -45° / 0°/ +45°

Miter cut: 0° to 45° to the left

Saw width at 90°: 205 x 65 mm

Saw width at 45°: 140 x 65 mm

Saw width at 2 x 45°

(double miter cut): 140 x 40 mm

Protection class: II / 쓑

Weight: approx. 15 kg

Laser class: 2

Wavelength of laser: 650 nm

Laser output: ≤ 1mW

Laser module power supply:

2 x 1.5 V Micro (AAA)

Noise emission values

The saw’s noise is measured in accordance

with EN 61029.

Idle speed

L

pA

sound pressure level 86 dB

K

pA

uncertainty 3 dB

L

WA

sound power level 99 dB

K

WA

uncertainty 3 dB

Total vibration values (vector sum of three

directions) determined in accordance with EN

61029.

Vibration emission value a

h

< 2.5 m/s

2

K uncertainty = 1.5 m/s

2

Warning!

The specified vibration value was established in

accordance with a standardized testing

method. It may change according to how the

electric equipment is used and may exceed the

specified value in exceptional circumstances.

The specified vibration value can be used to

compare the equipment with other electric

power tools.

The specified vibration value can be used for

initial assessment of a harmful effect.

Reduce noise generation and vibration to a

minimum!

 Use only equipment that is in perfect

condition.

 Maintain and clean the equipment regularly.

 Adopt your way of working to the

equipment.

 Do not overload the equipment.

 Have the equipment checked if necessary.

 Switch off the equipment when not in use.

7. Before starting the equipment

7.1 General information

 The equipment must be set up where it can

stand securely, i.e. it should be bolted to a

workbench, a universal base frame or

similar.

 All covers and safety devices have to be

properly fitted before the equipment is

switched on.

 It must be possible for the blade to run

freely.

 When working with wood that has been

processed before, watch out for foreign

bodies such as nails or screws, etc.

 Before you press the ON/OFF switch check

that the saw blade is fitted correctly. Moving

parts must run smoothly.

 Before you connect the equipment to the

power supply make sure the data on the

rating plate are identical to the mains data.

16

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 16

17

GB

7.2 Assembling the saw (Fig. 1-2, 4-6)

 To adjust the turntable (16), loosen the

locking grip (13) by approx. 2 turns and

press the latched position lever (12) to

disengage the turntable (16) (Figure 4).

 To release the saw from its bottom position,

apply light downward pressure to the

machine head (5). At the same time pull the

safety pin (25) out of the motor mount. Turn

the safety pin (25) through 90° so that the

saw remains unlocked (Fig. 1-2).

 Swing the machine head (5) up until the

release lever (3) latches into place (Fig. 1).

 Fit the clamping devices (8) on the left

and/or right side of the fixed saw table (17)

(Fig. 1).

 Undo the locking screws for the workpiece

support (10) (Fig. 5).

 Mount the workpiece support (9) on the

fixed saw table (17) and tighten the

appropriate locking screw (10) (Fig. 5).

 Mount the second workpiece support (9) on

the opposite side of the saw and secure

with the appropriate locking screw (10).

 When the locking screw (23) is loosened,

you can tilt the machine head (5) to the left

by up to 45° (Fig. 1-2).

 Screw the additional stability bar (18) to the

back of the equipment (Fig. 6).

7.3 Precision adjustment of the stop for

crosscut 90° (Fig. 7-8)

 No stop angle included.

 Fasten the turntable (16) in 0° position.

 Undo the locking screw (23) and move the

machine head (5) all the way to the right

using the handle (1).

 Place the 90° angular stop (z) between the

blade (7) and the turntable (16).

 Slacken the counternut (d). Adjust the

adjustment screw (90°) (31) until the angle

between the blade (7) and the turntable (16)

equals 90°.

 Retighten the counternut (d) to secure this

setting.

 Check the position of the pointer (21) on the

scale (20). If necessary, release the pointer

(21) with a crosstip screwdriver, move to the

0° position of the scale (20) and retighten.

7.4 Precision adjustment of the stop for

miter cut 45° (Fig. 1, 7, 10-11)

 No stop angle included.

 Fasten the turntable (16) in 0° position.

 Undo the locking screw (23) and move the

machine head (5) all the way to the left

using the handle, until it coincides at 45°.

 Place the 45° stop angle (y) between the

blade (7) and the turntable (16).

 Adjust the adjustment screw (32) so that the

angle between the blade (7) and the

turntable (16) equals exactly 45°.

8. Operation

8.1 Cross cut 90° and turntable 0°

(Fig. 1-3, 12)

Important! The integral resetting springs will

automatically lift the machine head. Do not

simply let go of the handle (1) after cutting, but

allow the machine head (5) to rise slowly,

applying slight counter pressure as it does so.

For cutting widths up to approx. 100 mm it is

possible to fix the saw’s drag function with the

locking screw for drag guide (24) in rear

position. If the cutting width exceeds 100 mm

you must ensure that the locking screw for drag

guide (24) is slackened and that the machine

head (5) can be moved.

Important. To make 90° crosscuts, the

adjustable stop rail (29) must be fixed at the

inner position.

 Open the locking lever (30) for the

adjustable stop rail and push the adjustable

stop rail inwards.

 The adjustable stop rail (29) must be fixed

far enough in front of the innermost position

that the distance between the stop rail (29)

and the saw blade (7) amounts to a

maximum of 5mm.

 Before making a cut, check that the stop rail

(29) and the saw blade (7) cannot collide.

 Secure the locking lever (30) again.

 Move the machine head (5) to its upper

position.

 Use the handle (1) to push back the

machine head (5) and fix it in this position if

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 17

required (dependent on the cutting width).

 Place the piece of wood to be cut at the stop

rail (19) and on the turntable (16).

 Lock the material with the clamping device

(8) on the fixed saw table (17) to prevent the

material from moving during the cutting

operation.

 Push down the release lever (3) to release

the machine head (5).

 Press the ON/OFF switch (2) to start the

motor.

 With the drag guide (26) fixed in place: use

the handle (1) to move the machine head

(5) steadily and with light pressure

downwards until the saw blade (7) has

completely cut through the workpiece.

 With the drag guide (26) not fixed in place:

pull the machine head (5) all the way to the

front. Lower the handle (1) to the very

bottom by applying steady and light

downward pressure. Now push the machine

head (5) slowly and steadily to the very

back until the saw blade (7) has completely

cut through the workpiece.

 When the cutting operation is completed,

move the machine head (5) back to its

upper (home) position and release the

ON/OFF button (2).

8.2 Cross cut 90° and turntable 0° - 45°

(Fig. 1-3, 13)

The crosscut saw can be used to make

crosscuts of 0° -45° to the left and 0° -45° to the

right in relation to the stop rail.

Important. To make 90° crosscuts, the

adjustable stop rail (29) must be fixed at the

inner position.

 Open the locking lever (30) for the

adjustable stop rail and push the adjustable

stop rail inwards.

 The adjustable stop rail (29) must be fixed

far enough in front of the innermost position

that the distance between the stop rail (29)

and the saw blade (7) amounts to a

maximum of 5mm.

 Before making a cut, check that the stop rail

(29) and the saw blade (7) cannot collide.

 Secure the locking lever (30) again.

 Release the turntable (16) by slackening the

locking grip (13).

 Press the latched position lever (12). Turn

the turntable (16) and scale pointer (14) to

the desired angular setting on the scales

(15) and lock into place with the locking grip

(13). The saw has locking positions at

angles of - 45°, -30°, -22.5°, -15°, 0°, 15°,

22.5°, 30° and 45°, at which you can

engage latched position lever (12).

 Cut as described under section 8.1.

8.3 Miter cut 0°- 45° and turntable 0°

(Fig. 1-3, 14)

The crosscut saw can be used to make miter

cuts of 0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw

head), the adjustable stop rail (29) must be

fixed at the outer position.

 Open the locking lever (30) for the

adjustable stop rail and push the adjustable

stop rail outwards.

 The adjustable stop rail (29) must be fixed

far enough in front of the innermost position

that the distance between the stop rail (29)

and the saw blade (7) amounts to a

maximum of 5mm.

 Before making a cut, check that the stop rail

(29) and the saw blade (7) cannot collide.

 Secure the locking lever (30) again.

 If required, dismantle the clamping device

(8) or mount on the opposite side of the

fixed saw table (17).

 Move the machine head (5) to its upper

position.

 Fasten the turntable (16) in 0° position.

 Undo the locking screw (23). Use the

handle (1) to tilt the machine head (5) to the

left until the pointer (21) points to the

required angle on the scale (20).

 Re-tighten the fixing screw (23).

 Use the handle (1) to push back the

machine head (5) and fix it in this position if

required (dependent on the cutting width).

 Place the piece of wood to be cut at the stop

rail (19) and on the turntable (16).

 Lock the material with the clamping device

(8) on the fixed saw table (17) to prevent the

material from moving during the cutting

operation.

 Push down the release lever (3) to release

the machine head (5).

18

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 18

 Press the ON/OFF switch (2) to start the

motor.

 With the drag guide (26) fixed in place: use

the handle (1) to move the machine head

(5) steadily and with light pressure

downwards until the saw blade (7) has

completely cut through the workpiece.

 With the drag guide (26) not fixed in place:

pull the machine head (5) all the way to the

front. Lower the handle (1) to the very

bottom by applying steady and light

downward pressure. Now push the machine

head (5) slowly and steadily to the very

back until the saw blade (7) has completely

cut through the workpiece.

 When the cutting operation is completed,

move the machine head (5) back to its

upper (home) position and release the

ON/OFF button (2).

8.4 Miter cut 0°- 45° and turntable 0°- 45°

(Fig. 1-3, 15)

The crosscut saw can be used to make miter

cuts to the left of 0°- 45° in relation to the work

face and, at the same time, 0° - 45° to the left or

0° - 45° to the right in relation to the stop rail

(double miter cut).

Important. To make miter cuts (inclined saw

head), the adjustable stop rail (29) must be

fixed at the outer position.

 Open the locking lever (30) for the

adjustable stop rail and push the adjustable

stop rail outwards.

 The adjustable stop rail (29) must be fixed

far enough in front of the innermost position

that the distance between the stop rail (29)

and the saw blade (7) amounts to a

maximum of 5mm.

 Before making a cut, check that the stop rail

(29) and the saw blade (7) cannot collide.

 Secure the locking lever (30) again.

 If required, dismantle the clamping device

(8) or mount on the opposite side of the

fixed saw table (17).

 Move the machine head (5) to its upper

position.

 Release the turntable (16) by slackening the

locking grip (13).

 Press the latched position lever (12). Turn

the turntable (16) and scale pointer (14) to

the desired angular setting on the scales

(15) and lock into place with the locking grip

(13).

 Undo the locking screw (23) and use the

handle (1) to tilt the machine head (5) to the

left until it coincides with the required angle

value (in this connection see also section

8.3).

 Re-tighten the fixing screw (23).

 Cut as described under section 8.3.

8.5 Limiting the cutting depth (Fig. 16)

 The cutting depth can be infinitely adjusted

using the screw (27). To do this loosen the

knurled nut on the screw (27). Move the

stop for the cutting depth limiter (28) to the

outside. Turn the screw (27) in or out to set

the required cutting depth. Then re-tighten

the knurled nut on the screw (27).

 Check the setting by completing a test cut.

8.6 Sawdust bag (Fig. 2)

The saw is equipped with a debris bag (22) for

sawdust and chips.

The debris bag (22) can be emptied by means

of a zipper at the bottom.

8.7 Changing the saw blade (Fig. 1, 17-20)

Remove the power plug!

Important.

Wear safety gloves when changing the saw

blade. Risk of injury.

 Swing up the machine head (5). Use the

safety pin (25) to lock the machine head in

this position.

 Press the release lever (3). Swing up the

saw blade guard (6) to the point where the

recess in the saw blade guard (6) is above

the flange bolt (33).

 Press the saw shaft lock (4) with one hand.

With the other hand position the wrench (c)

over the flange bolt (33).

 Firmly press the saw shaft lock (4) and

slowly rotate the flange bolt (33) in

clockwise direction. The saw shaft lock (4)

engages after no more than one rotation.

 Now, using a little more force, slacken the

flange screw (33) in the clockwise direction.

 Turn the flange screw (33) right out and

remove the external flange (34).

19

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 19

 Take the blade (7) off the inner flange (40)

and pull downwards and out.

 Carefully clean the flange screw (33), outer

flange (34) and inner flange (40).

 Fit and fasten the new saw blade (7) in

reverse order.

 Important! The cutting angle of the teeth, in

other words the direction of rotation of the

saw blade (7) must coincide with the

direction of the arrow on the housing.

 Before continuing your work make sure that

all safety devices are in good working

condition.

 Important! Every time that you change the

saw blade (7), check to see that it spins

freely in the table insert (11) in both

perpendicular and 45° angle settings.

 Important! The work to change and align

the saw blade (7) must be carried out

correctly.

8.8 Transport (Fig. 1-3)

 Retighten the locking grip (13) to secure the

turntable (16) in place.

 Activate the release lever (3), press the

machine head (5) downwards and secure

with the safety pin (25). The saw is now

locked in its bottom position.

 Fix the saw’s drag function with the locking

screw for drag guide (24) in rear position.

 Carry the equipment by the fixed saw table

(17).

 When reassembling the equipment proceed

as described under section 7.2.

8.9 Using the laser (Fig. 21-23/Item 35)

 To switch on: Move the ON/OFF switch of

the laser (36) to the “1” position. A laser line

is projected onto the material you wish to

process, providing an exact guide for the

cut.

 To switch off: Move the ON/OFF switch of

the laser (36) to the “0” position.

 Setting the laser: The laser is adjusted

with the screw (39) and glued in place ex-

works. Further adjustment of the laser

during operation is not required. Important.

Do not look into the laser beam.

 Replacing the battery: Switch off the laser

(35). Remove the battery compartment

cover (38). Remove the batteries and

replace with new batteries (2 x 1.5 Volt

Type R03, LR 03 Micro, AAA) Check that

the battery terminals are positioned

correctly when inserting new batteries.

Close the battery compartment (37) again.

9. Replacing the power cable

If the power cable for this equipment is

damaged, it must be replaced by the

manufacturer or its after-sales service or

similarly trained personnel to avoid danger.

10. Cleaning, maintenance and

ordering of spare parts

Always pull out the mains power plug before

starting any cleaning work.

10.1 Cleaning

 Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it down with compressed air at

low pressure.

 We recommend that you clean the

equipment immediately after you use it.

 Clean the appliance regularly with a damp

cloth and some soft soap. Do not use

cleaning agents or solvents; these may be

aggressive to the plastic parts in the

appliance. Ensure that no water can get into

the interior of the equipment.

10.2 Carbon brushes

In case of excessive sparking, have the carbon

brushes checked only by a qualified electrician.

Important. The carbon brushes should not be

replaced by anyone but a qualified electrician.

10.3 Servicing

There are no parts inside the equipment which

require additional maintenance.

20

GB

Anleitung_LB4_4300688:_ 20.12.2010 10:08 Uhr Seite 20

Stránka sa načítava...

Parkside PKS 1700 A1 Operation And Safety Notes Original Operating Instructions

Tento návod je vhodný aj pre

Parkside PKS 1700 A1 Operation And Safety Notes Original Operating Instructions

v iných jazykoch

Súvisiace články

Ostatné dokumenty