1
GB
English,1
Contents
Installation, 2-3
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washer-dryer description, 4-5
Control panel
Leds
Starting and Programmes, 6
Briefly: how to start a programme
Programme table
Personalisations, 7
Setting the temperature
Setting the drying cycle
Functions
Detergents and laundry, 8
Detergent dispenser
Preparing your laundry
Special items
Precautions and advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning your appliance
Cleaning the detergent dispenser
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
Before calling for Assistance
WASHER-DRYER
WIDXXL 126
Instructions for use
GB
Italiano,25
I
Espanol,13
ES
ÅËËÇÍÉÊÁ,37
GR
2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the Washer-dryer to inform the
new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the Washer-dryer.
2. Check whether the Washer-dryer has been
damaged during transport. If this is the case, do not
install it and contact your retailer.
3. Remove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
Washer-dryer needs to be moved to another location.
Packaging materials are not children's toys.
Levelling
1. Install the Washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure);
the angle of inclination,
measured according to
the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the Washer-
dryer.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose
and screw the latter
onto a cold water tap
with a 3/4 gas threaded
mouth (see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the Washer-dryer,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Never use hoses that have already been used.
Installation
A
GB
Technical details
Model
WIDXXL 126
Dimensions
59.5 cm wide
85 cm high
53.5 cm deep
Capacity
from 1 to 7 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electric
connections
please refer to the technical data plate
fixed to the machine
Wate r
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rpm
Control
programmes
according to
EN 50229
directive
Wash: programme 2; temperature 60°C;
run with a load of 7 kg.
Drying: first drying cycle performed with
a 2 kg load and the DRYING knob on
the setting;
Second drying cycle performed with a 5
kg load and the DRYING knob on the
setting.
This appliance is compliant with the
following European Community
Directives:
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
- 2006/95/CE (Low Voltage)
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from
the floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
65 - 100 cm
4
GB
Washer-dryer description
Control panel
Detergent dispenser
ON-OFF
Button
START/RESET
Button
TEMPERATURE
Knob
PROGRAMME
Knob
Leds
FUNCTION
Buttons
ON-OFF/
DOOR
LOCK
Led
Detergent dispenser: to add detergent and fabric
softener (see page 8).
LEDS: to find out which wash cycle phase is under
way.
If the Delay Timer function has been set, the time
left until the programme starts will be indicated (see
page 5).
DRYING knob: to set the desired drying cycle
(see page 7).
FUNCTION buttons: to select the functions
available. The button corresponding to the function
selected will remain on.
TEMPERATURE knob: to set the temperature or
the cold wash cycle (see page 7).
START/RESET button: to start the programmes or
cancel any incorrect settings.
ON-OFF/DOOR LOCK Led: to find out whether the
Washer-dryer is on and if the appliance door can be
opened (see page 5).
ON/OFF button: to turn the Washer-dryer on and off.
PROGRAMME knob: to select the wash
programmes. The knob stays still during the cycle.
DRYING
Knob
Note: to avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner
by continuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than
the set frequency.
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
GB
ON-OFF/DOOR LOCK led
If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any
damages, wait for the LED to flash before you open the appliance door.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED
indicates there is an abnormality (see page 11).
Cycle phase under way:
During the wash cycle, the LEDs gradually illumina-
te on to indicate the cycle phase under way:
Prewash / Wash
Rinse
Spin cycle
Drying
Note:
- during draining, the LED corresponding to the
Spin cycle phase will be turned on.
- when the drying cycle is complete, the indicator
light relative to phase
will flash, to indicate that
the DRYING knob needs to be set back to the 0
setting.
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding
button is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the
function will not be enabled.
If you set a function that is incompatible with
another function you selected previously, only the
last one selected will be enabled.
Leds
The LEDS provide important information.
This is what they can tell you:
Delay set:
If the Delay Timer function has been enabled (see
page. 7), once you have started the programme,
the LED corresponding to the delay set will begin to
flash:
As time passes, the remaining delay will be
displayed, and the corresponding LED will flash:
Once the set delay is complete, the flashing LED will
turn off and the programme set will start.
6
GB
Starting and Programmes
Programme table
Briefly: starting a programme
1. Switch the Washer-dryer on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine and
shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the drying cycle if necessary (see page 7).
6. Add the detergent and any fabric softener (see page 8).
7. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
8. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the Washer-dryer
off by pressing button
.
Notes
-For programme 9, we advise against exceeding a wash load of 3.5 kg.
-For programme 13 we advise against exceeding a wash load of 2 kg.
-For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can wash
different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Type of fabric and
degree of soil
Prog. Temp.
Drying
Cycle
Detergent
Fabric
softener
Cycle
length
(minutes)
Description of wash cycle
pre-wash wash
Standard
Cotton:
Extremely soiled whites (sheets,
tablecloths, etc.)
1
90°C
170
Pre-wash, wash cycle, rinse cycles,
intermediate and final spin cycles
Cotton:
Extremely soiled whites (sheets,
tablecloths, etc.)
2
90°C
155
Wash cycle, rinse cycles, intermediate
and final spin cycles
Cotton:
Heavily soiled whites and fast
colours
2
60°C
153
Wash cycle, rinse cycles, intermediate
and final spin cycles
Cotton:
Heavily soiled whites and delicate
colours
2
40°C
115
Wash cycle, rinse cycles, intermediate
and final spin cycles
Cotton:
Slightly soiled whites and delicate
colours (shirts, jumpers, etc.)
3
40°C
85
Wash cycle, rinse cycles, intermediate
and final spin cycles
Synthetics:
Heavily soiled fast colours
(baby linen, etc.)
4
6
0°C
85
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Synthetics:
Heavily soiled fast colours
(baby linen, etc.)
4
40°C
75
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Wool
5
40°C
55
Wash cycle, rinse cycles, delicate
spin cycle
Very delicate fabrics (curtains, silk,
viscose, etc.)
6
30°C
55
Wash cycle, rinse cycles, anti-
crease or draining cycle
Drying cotton
7
Drying delicates
8
Time 4 you
Cotton:
Heavily soiled whites and fast
colours
9
60°C
60
Wash cycle, rinse cycles, intermediate
and final spin cycles
Synthetics:
Delicate colours (all types of
slightly soiled garments)
10
40
°C
40
Wash cycle, rinse cycles, delicate
spin cycle
Synthetics:
Delicate colours (all types of
slightly soiled garments)
11
30°C 30
Wash cycle, rinse cycles and
delicate spin cycle
Sport
Sports shoes
(MAX. 2 pairs)
12
30
°C
50
Cold wash (without detergents),
wash cycle, rinse cycles, and delicate
spin cycle
Fabrics for sportswear
(Tracksuits, shorts, etc.)
13
30°C 60
Wash cycle, rinse cycles, intermediate
and final spin cycles
PARTIAL PROGRAMMES
Rinse Rinse cycles and spin cycle
Spin cycle Draining and spin cycle
Drain Drain
GB
Personalisations
C
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash (
).
Set the drying cycle
Turn the DRYING knob to set the desired drying type.
Two options are available:
A - Based on time: From 40 minutes to 180.
B - Based on the damp level of the dry clothes:
Iron
: slightly damp clothes, easy to iron.
Hanger
: dry clothes to put away.
Cupboard
: very dry clothes, recommended for towelling
and bathrobes.
A cooling stage is foreseen at the end of the drying cycle.
If your laundry load to wash and dry is exceptionally in excess
of the maximum load foreseen (see table opposite), perform
the wash cycle, and when the programme is complete, divide up the garments and put part of them back in the
drum. Now follow the instructions provided for a dry only cycle. Repeat this procedure for the remainder of the load.
Dry only
Turn the PROGRAMME knob to one of the drying settings (7-8) depending on the type of fabric, then select the
desired drying type using the DRYING knob.
Important: - A spin cycle is carried out during the drying if you have set a cotton programme and a level of
dryness (Cupboard
, Hanger , Iron ).
- For cotton loads of less than 1 Kg, use the drying programme designed for delicate fabrics.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
Fabric
type
Load type Max.
load
(kg) Cup-
board
Hanger Iron
Cotton,
Linen
Clothing of different sizes
5 180 170 140
Cotton Terry towels
5 180 170 140
Terit al,
Cotton
Sheets, Shirts
3 140 120 100
Acrylics Pyjamas, socks, etc.
170 6560
Nylon Slips, tights, stockings, etc.
170 6560
Table of drying times
The data contained in the
table are purely indicative.
Function Effect Comments
Enabled with
programmes:
Delay
Timer
Delays the start
of the wash by
up to 9 hours.
Press the button repeatedly until the LED corresponding to the
desired delay is turned on.
The fifth time the button is pressed, the function will be disabled.
N.B.: Once you have pressed the Start/Reset button, the delay
can only be decreased if you wish to modify it.
All
Easy iron
This option
reduces the
amount of
creasing on
fabrics, making
them easier to
iron.
When this function is set, programmes 4, 6 will end with the
laundry left to soak (Anti-crease) and the Rinse cycle phase
LED will flash.
- to conclude the cycle, press the START/RESET button;
- to run the draining cycle alone, set the knob to the relative
symbol and press the START/RESET button.
This function is incompatible with the STAIN REMOVAL function.
If you also want to run the drying cycle, this button is enabled
only if combined with level (Ir on ).
3, 4, 6,
9, 10,
Rinse cycle.
Extra
Rinse
Increases the
efficiency of the
rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, 3, 4, 9,
10, 12, 13,
Rinse cycle.
1200-600
Reduces the
spin speed.
All
programmes
except for 6, 7,
8 and draining.
8
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your
appliance and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
(powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in
immediately prior to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow from the grid.
Do not use hand wash detergent because it may
form too much foam.
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
Empty all pockets and check for loose buttons.
Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 7 kg
Synthetic fabrics: max 3 kg
Delicate fabrics: max 2 kg
Wool: max 1,5 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme 6
which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1,5 kg.
Detergents and laundry
1
2
3
9
GB
Precautions and advice
The Washer-dryer was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not open the detergent dispenser while the
appliance is in operation.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
The appliance door tends to get quite hot during
the wash cycle.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
Do not use the appliance to dry foam rubber or
similar elastomers.
Make sure that the water tap is turned on during
the drying cycles.
This washer-dryer can only be used to dry clothes
which have been pre-washed in water.
Disposal
Disposing of the packaging material:
observe local regulations, so the packaging can
be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest Indesit
technology, your washing machine only needs less
than half the amount of water to get the best results:
an objective reached to respect the environment.
Saving on detergent, water, energy and time
To avoid wasting resources, the Washer-dryer
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
The Delay Timer option (see page 7) helps to
organise your wash cycles accordingly.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity
supply
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for your appliance door and
drum
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The Washer-dryer is fitted with a self-cleaning pump
that does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into
the pre-chamber that protects the pump, situated in
the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front of the
Washer-dryer (see
figure);
2. unscrew the lid
rotating it anti-
clockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
11
GB
Troubleshooting
Your Washer-dryer could fail to work. Before calling for Assistance (see page 12), make sure the problem can't
easily be solved by consulting the following list.
Problem
The washer-dryer won't start.
The wash cycle won't start.
The washer-dryer fails to load
water.
The washer-dryer continuously
loads and unloads water.
The washer-dryer does not
drain or spin.
The washer-dryer vibrates too
much during the spin cycle.
The washer-dryer leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
There is too much foam.
The washer-dryer does not dry.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance door is not shut properly.
The
button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
A delayed start has been set (using the Delay Timer, see page 7).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and call for Assistance. If the dwelling is on one of
the upper floors of a building, there may be drain trap problems causing the
Washer-dryer to load and unload water continuously. In order to avoid such
an inconvenience, special anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The Washer-dryer is not level (see page 2).
The Washer-dryer is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
You used too much detergent.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set (using the Delay Timer, see page 7).
the DRYING knob is on the 0 setting.
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washer-dryer.
Service
13
ES
Espanol
Sumario
Instalación, 14-15
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Descripción de la lavasecadora, 16-17
Panel de control
Luces testigo
Puesta en marcha y Programas, 18
En la práctica: poner en marcha un programa
Tabla de programas
Personalizaciones, 19
Seleccione la temperatura
Seleccione el secado
Funciones
Detergentes y ropa, 20
Cajón de detergentes
Preparar la ropa
Prendas especiales
Precauciones y consejos, 21
Seguridad general
Eliminaciones
Ahorrar y respetar el ambiente
Mantenimiento y cuidados, 22
Excluir el agua y la corriente eléctrica
Limpiar la lavasecadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Anomalías y soluciones, 23
Asistencia, 24
Antes de llamar a la Asistencia Técnica
ES
LAVASECADORA
WIDXXL 126
Instrucciones para el uso
14
ES
Es importante conservar este manual para poder
consultarlo en cualquier momento. En caso de venta,
de cesión o de traslado, verifique que permanezca
junto con la lavasecadora para informar al nuevo
propietario sobre el funcionamiento y brindar las
correspondientes advertencias.
Lea atentamente las instrucciones: ellas contienen
importante información sobre la instalación, el uso y la
seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavasecadora.
2. Controle que la lavasecadora no haya sufrido
daños durante el transporte. Si estuviera dañada no
la conecte y llame al revendedor.
3. Quite los 4 tornillos
de protección para el
transporte y la arandela
de goma con el corres-
pondiente distanciador,
ubicados en la parte
posterior (ver la figura).
4. Cierre los orificios con los tapones de plástico
suministrados con el aparato.
5. Conserve todas las piezas: cuando la lavasecadora deba
ser transportada nuevamente, deberán volver a colocarse.
Los embalajes no son juguetes para los niños.
Nivelación
1. Instale la lavasecadora sobre un piso plano y rígido, sin
apoyarla en las paredes, muebles ni en ningún otro aparato.
2. Si el piso no está
perfectamente horizontal,
compense las irregulari-
dades desenroscando o
enroscando los pies
delanteros (véase la
figura); el ángulo de
inclinación medido sobre
la superficie de trabajo,
no debe superar los 2º.
Una cuidadosa nivelación brinda estabilidad a la
máquina y evita vibraciones, ruidos y desplazamien-
tos durante el funcionamiento. Cuando se instala
sobre moquetas o alfombras, regule los pies para
conservar debajo de la lavasecadora un espacio
suficiente para la ventilación.
Conexiones hidráulicas y eléctricas
Conexión del tubo de alimentación de agua
1. Introduzca la junta A
en el extremo del tubo
de alimentación y
enrósquelo a un grifo de
agua fría con boca
roscada de 3/4 gas
(véase la figura).
Antes de conectarlo,
haga correr el agua
hasta que salga limpia.
2. Conecte el tubo de
alimentación a la
lavasecadora enroscán-
dolo en la toma de agua
correspondiente ubica-
da en la parte posterior
arriba y a la derecha
(véase la figura).
3. Verifique que el tubo no tenga pliegues ni estran-
gulaciones.
La presión de agua del grifo debe estar comprendi-
da dentro de los valores contenidos en la tabla de
Datos técnicos (ver la página del costado).
Si la longitud del tubo de alimentación no fuera
suficiente, diríjase a una tienda especializada o a un
técnico autorizado.
No utilice nunca tubos ya usados.
Instalación
A
15
ES
Conexión del tubo de descarga
Conecte el tubo de
descarga, sin plegarlo, a
un desagüe de pared
ubicado a una distancia
del piso comprendida
entre 65 y 100 cm;
o apóyelo al borde de
un lavabo o de una
bañera, uniendo la guía
suministrada con el
aparato, al grifo (véase
la figura). El extremo
libre del tubo de des-
carga no debe perma-
necer sumergido en el
agua.
No se aconseja utilizar tubos de prolongación, de
todos modos, si es indispensable, la prolongación
debe tener el mismo diámetro del tubo original y no
superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
la toma tenga la conexión a tierra y haya sido
hecha según las normas legales;
la toma sea capaz de soportar la carga máxima
de potencia de la máquina indicada en la tabla de
Datos técnicos (ver al costado);
la tensión de alimentación esté comprendida
dentro de los valores indicados en la tabla de
Datos técnicos (ver al costado);
la toma sea compatible con el enchufe de la
lavadora. Si no es así, sustituya la toma o el
enchufe.
La lavadora no debe ser instalada al aire libre, ni
siquiera si el lugar está preparado, ya que es muy
peligroso dejarla expuesta a la lluvia o a las tormentas.
Una vez instalada la lavadora, la toma de corriente
debe ser fácilmente accesible.
No utilice alargadores ni conexiones múltiples.
El cable no debe estar plegado ni sufrir compresiones.
El cable de alimentación debe ser sustituido sólo
por técnicos autorizados.
¡Atención! La empresa fabricante declina toda
responsabilidad en caso de que estas normas no
sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso, realice un
ciclo de lavado con detergente y sin ropa, seleccio-
nando el programa a 90ºC sin prelavado.
65 - 100 cm
Datos técnicos
Modelo
WIDXXL 126
Dimensiones
ancho 59,5 cm.
altura 85 cm.
profundidad 53,5 cm.
Capacidad
de 1 a 7 kg para el lavado;
de 1 a 5 kg para el secado.
Conexiones
eléctricas
ver la placa de características
técnicas aplicada en la máquina
Conexiones
hídricas
presión máxima 1 MPa (10 bar)
presión mínima 0,05 MPa (0,5 bar)
capacidad del cesto 52 litros
Velocidad de
centrifugado
máxima 1200 r.p.m.
Programas de
control según la
norma EN 50229
lavado: programa 2; temperatura
60ºC; efectuado con 7 kg. de carga.
secado: primer secado realizado
con 2 kg de cargay el mando de
SECADO en la posición ;
segundo secado realizado con 5 kg
de carga y el mando de SECADO en
la posición .
Esta máquina cumple con lo
establecido por las siguientes
Directivas de la Comunidad:
- 89/336/CEE del 03/05/89
(Compatibilidad Electromagnética) y
sucesivas modificaciones
- 2002/96/CE
- 2006/95/CE (Baja Tensión)
16
ES
Panel de control
Descripción de la lavasecadora
Cajón de detergentes
Botón de
ENCENDIDO/
APAGADO
Botón de
START/RESET
Cajón de detergentes: para cargar detergentes y
aditivos (véase la pág. 20).
Luces testigo: para seguir el estado de avance del
programa de lavado.
Si se seleccionó la función Delay Timer, indicarán el
tiempo que falta para la puesta en marcha del
programa (ver la pág. 17).
Mando de SECADO: para seleccionar el secado
deseado (ver la pág. 19).
Botones de FUNCIÓN: para seleccionar las funcio-
nes disponibles. El botón correspondiente a la
función seleccionada permanecerá encendido.
Mando de TEMPERATURA: para seleccionar la
temperatura o el lavado en frío (ver la pág. 19).
Botón de START/RESET: para poner en marcha
los programas o anular las selecciones incorrectas.
Luz indicadora de ENCENDIDO/PUERTA BLO-
QUEADA: para saber si la lavasecadora está encen-
dida y si la puerta se puede abrir (ver la pág. 17).
Botón de ENCENDIDO/APAGADO: para encender
y apagar la lavasecadora.
Mando de PROGRAMAS: para elegir los progra-
mas. Durante el programa el mando no se mueve.
Mando de
TEMPERATURA
Mando de
PROGRAMAS
Luces
testigo
Botones de
FUNCIÓN
Mando de
SECADO
Luz indicadora de
ENCENDIDO/PUERTA
BLOQUEADA
Notas: Para evitar vibraciones excesivas, antes de cada centrifugado, la máquina distribuye la carga de modo
uniforme, esto se produce efectuando rotaciones continuas del cesto a una velocidad ligeramente superior a la
del lavado.
Aún cuando después de repetidos intentos, la carga no se distribuye perfectamente, la máquina realiza el
centrifugado a una velocidad inferior a la prevista.
Cuando existe un excesivo desequilibrado, la máquina efectúa la distribución en lugar del centrifugado.
Los intentos de equilibrado pueden aumentar la duración total del ciclo hasta un máximo de 10 minutos.
17
ES
Luz indicadora de ENCENDIDO/PUERTA BLOQUEADA
La luz testigo encendida indica que la puerta está bloqueada para impedir aperturas accidentales; para evitar
daños es necesario esperar que la luz testigo centellee antes de abrir la puerta.
El centelleo rápido de la luz indicadora de ENCENDIDO/PUERTA BLOQUEADA simultáneamente con, al me-
nos, el de otra luz testigo, indica una anomalía (ver la pág. 23).
Fase en curso:
Durante el ciclo de lavado, las luces testigo se
encenderán progresivamente para indicar su
estado de avance.
Prelavado / Lavado
Aclarado
Centrifugado
Secado
Nota:
- durante la fase de descarga se iluminará la luz
testigo correspondiente a la fase de Centrifugado.
- al finalizar el ciclo de secado, la luz testigo co-
rrespondiente a la fase
centelleará para indicar
que es necesario llevar el mando de SECADO a la
posición 0.
Botones de FUNCIÓN
Los BOTONES DE FUNCIÓN también actúan
como luces testigo.
Al seleccionar una función, el botón correspondien-
te se iluminará.
Si la función seleccionada no es compatible con el
programa elegido, el botón centelleará y la función
no se activará.
Cuando se seleccione una función incompatible
con otra seleccionada precedentemente, perma-
necerá activa sólo la última selección realizada.
Luces testigo
Las luces testigo suministran información importante.
He aquí lo que nos dicen:
Retraso seleccionado:
Si fue activada la función Delay Timer (ver la pág.
19), después de haber puesto en marcha el progra-
ma, comenzará a centellear la luz testigo correspon-
diente al retraso fijado:
Con el transcurrir del tiempo se visualizará el retraso
residual y el centelleo de la luz testigo correspondiente:
Una vez transcurrido el tiempo de retraso fijado, la
luz testigo centelleante se apagará y comenzará el
programa seleccionado.
18
ES
Tipos de tejidos y de suciedad Programas
Te m p e -
ratura
Secado
Detergente
Suavi-
zante
Duración
del ciclo
(m in utos)
Descripción del ciclo de lavado
prelav. lavado
Estándar
A
lgodón
:
Blancos sumamente
sucios (sábanas, manteles, etc.)
1
90°C
170
Prelavado, lavado, aclarados,
centrífugas intermedias y final
A
lgodón
:
Blancos sumamente
sucios (sábanas, manteles, etc.)
2
90°C
155
Lavado, aclarados, centrífugas
intermedias y final
A
lgodón
:
Blancos y coloreados
resistentes muy sucios
2
60°C
153
Lavado, aclarados, centrífugas
intermedias y final
A
lgodón
:
Blancos y coloreados
delicados muy sucios
2
40°C
115
Lavado, aclarados, centrífugas
intermedias y final
A
lgodón
:
Blancos poco sucios y
colores delicados
(camisas, camisetas, etc.)
3
40°C
85
Lavado, aclarados, centrífugas
intermedias y final
Sintéticos:
Colores resistentes
muy sucios (ropa para recién
nacidos, etc.)
4
60°C
85
Lavado, aclarados, antiarrugas o
centrífuga delicada
Sintéticos:
Colores resistentes
muy sucios (ropa para recién
nacidos, etc.)
4
40°C
75
Lavado, aclarados, antiarrugas o
centrífuga delicada
Lana
5
40°C
55
Lavado, aclarados y
centrifugación delicada
Tejidos muy delicados
(cortinas, seda, viscosa, etc.)
6
30°C
55
Lavado, aclarados, antiarrugas o
desague
Secado para telas de algodón
7
Secado para tejidos delicados
8
Tim e 4 you
A
lgodón
:
Blancos y coloreados
resistentes muy sucios
9
60°C
60
Lavado, aclarados, centrífugas
intermedias y final
Sintéticos:
Colores delicados (ropa
de todo tipo ligeramente sucia)
10
40
°C
40
Lavado, aclarados y centrífuga
delicada
Sintéticos:
Colores delicados (ropa
de todo tipo ligeramente sucia)
11
30°C 30
Lavado, aclarados y centrífuga
delicada
Sport
Calzado deportivo
(
MAX. 2 pares.
)
12
30
°C
50
Lavado en frío (sin detergente),
lavado, aclarados y centrifugación
delicada
Tejidos para ropa deportiva
(chandal, pantalón corto, etc.)
13
30°C 60
Lavado, aclarados, centrífugas
intermedias y final
PROGRAMAS PARCIALES
Aclarado Aclarados y centrifugación
Centrifugación Desague y centrifugación
Desague Desague
Puesta en marcha y Programas
Tabla de programas
En la práctica: poner en marcha un
programa
1. Encienda la lavasecadora pulsando el botón .
Todas las luces testigo se encenderán durante
algunos segundos, luego se apagarán y la luz
indicadora de ENCENDIDO/PUERTA BLOQUEADA
comenzará a centellear.
2. Cargue la ropa y cierre la puerta.
3. Seleccione el programa deseado con el mando de
PROGRAMAS.
4. Fije la temperatura de lavado (ver la pág. 19).
5. Seleccione el secado si es necesario (ver la pág. 19).
6. Vierta el detergente y los aditivos (véase la pág. 20).
7. Ponga en marcha el programa pulsando el botón
START/RESET.
Para anular, mantenga presionado el botón
START/RESET durante 2 segundos como mínimo.
8. Al finalizar el programa, la luz indicadora de ENCEN-
DIDO/PUERTA BLOQUEADA centelleará indicando
que la puerta se puede abrir. Extraiga la ropa y deje la
puerta semicerrada para permitir que el cesto se
seque. Apague la lavasecadora pulsando el botón
.
Notas
-En el programa 9 es aconsejable no superar una carga de ropa de 3,5 kg.
-En el programa 13 se aconseja no superar una carga de ropa de 2 kg.
-Para la descripción del antiarrugas: consulte Plancha fácil, página siguiente. Los datos contenidos en la tabla
tienen un valor indicativo.
Programa especial
Diario 30' (programa 11 para Sintéticos) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo:
dura sólo 30 minutos y de esa manera hace ahorrar energía y tiempo. Seleccionando el programa (11 a 30ºC)
es posible lavar conjuntamente tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 3 kg.
Se aconseja el uso de detergente líquido.
19
ES
Personalizaciones
C
Seleccione la temperatura
Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas en la pág. 18).
La temperatura se puede disminuir hasta el lavado en frío (
).
Seleccione el secado
Girando el mando de SECADO se selecciona el tipo de
secado deseado. Se han previsto dos posibilidades:
A - En base al tiempo: De 40 a 180 minutos.
B - En base al nivel de humedad de las prendas secadas:
Planchado
: prendas ligera-mente húmedas, fáciles de
planchar.
Seque y cuelgue
: prendas secas, listas para guardar.
Ropero
: prendas muy secas, aconsejado para toallas y
batas.
Al finalizar el secado continúa un período de enfriamiento.
Si excepcionalmente la carga de ropa para lavar y secar es
superior al máximo previsto (ver la tabla ubicada al costado), realice el lavado, y una vez finalizado el programa,
divida la carga y vuelva a colocar una parte en el cesto. A partir de ese momento, siga las instrucciones para
efectuar sólo el secado. Repita las mismas operaciones para la carga restante.
Sólo secado
Gire el mando de PROGRAMAS hasta una de las posiciones de secado (7-8) de acuerdo al tipo de tejido, luego
seleccione el tipo de secado deseado con el mando de SECADO.
Importante: - Durante el secado se efectuará un centrifugado si Ud. ha seleccionado uno de los programas
de algodón y uno de los niveles de secado (Ropero
, Seque y cuelgue , Planchado ).
- Para cargas de telas de algodón inferiores a 1 Kg, utilice el programa de secado correspondiente a los tejidos delicados.
Funciones
Las distintas funciones de lavado previstas por la lavasecadora permiten obtener la limpieza y el blanco desea-
dos. Para activar las funciones:
1. pulse el botón correspondiente a la función deseada de acuerdo con la tabla que se encuentra debajo;
2. el encendido del botón correspondiente indica que la función está activa.
Nota: El centelleo rápido del botón indica que la función correspondiente no se puede seleccionar para el programa elegido.
Tipo de
tela
Tipo de carga Carga
máx.
(kg) Ropero Seque y
cuelgue
Planchado
Algodón,
Lino
Ropa de distintas
dimensiones
5 180 170 140
Algodón Toallas
5 180 170 140
Terilene,
Algodón
Sábanas, Camisas
3 140 120 100
Acrílicos Pijamas,
calcetines, etc.
170 65 60
Nylon Combinaciones,
medias, etc.
170 65 60
Tabla de tiempos de secado
Los datos contenidos en la
tabla tienen un valor indicativo.
Funciones Efecto Notas para el uso
Activa con
los
programas:
Delay timer
Retrasa la puesta
en marcha de la
máquina hasta 9
horas.
Pulse varias veces el botón hasta encender la luz testigo
correspondiente al retraso deseado.
La quinta vez que se presione el botón, la función se desactivará.
Nota: Una vez pulsado el botón Start/Reset, se puede modificar el
valor del retraso sólo disminuyéndolo.
To d o s
Plancha
fácil
Reduce las
arrugas en los
tejidos,
facilitando el
planchado.
Seleccionando esta función, los programas 4, 6 se interrumpirán
con la ropa en remojo (Antiarrugas) y la luz indicadora de la fase
de Aclarado centelleará:
- para completar el ciclo pulse el botón START/RESET;
- para efectuar sólo la descarga coloque la perilla en el símbolo
correspondiente y pulse el botón START/RESET.
Si desea realizar también el secado, este botón funciona sólo
conjuntamente con el nivel (Planchado).
3, 4, 6,
9, 10,
Aclarado.
Aclarado
Extra
Aumenta la
eficacia del
aclarado.
Es aconsejable con la lavadora a plena carga o con dosis elevadas
de detergente.
1, 2, 3, 4, 9,
10, 12, 13
Aclarado.
1200-600
Disminuye la
velocidad de
centrifugado.
To d o s
excepto el
6, 7, 8 y la
descarga.
20
ES
Cajón de detergentes
El buen resultado del lavado depende también de la
correcta dosificación del detergente: si se excede la
cantidad, no se lava de manera más eficaz, sino que
se contribuye a encostrar las partes internas de la
lavasecadora y a contaminar el ambiente.
Extraiga el cajón de
detergentes e introduz-
ca el detergente o el
aditivo de la siguiente
manera:
cubeta 1: Detergente para prelavado (en polvo)
cubeta 2: Detergente para lavado
(en polvo o líquido)
El detergente líquido se debe verter sólo antes de la
puesta en marcha.
cubeta 3: Aditivos (suavizante, etc.)
El suavizante no se debe volcar fuera de la rejilla.
No use detergentes para el lavado a mano ya que
producen demasiada espuma.
Preparar la ropa
Subdivida la ropa según:
- el tipo de tejido / el símbolo en la etiqueta.
- los colores: separe las prendas de color y las blancas.
Vacíe los bolsillos y controle los botones.
No supere los valores indicados, referidos al peso
de la ropa seca:
Tejidos resistentes: max 7 kg.
Tejidos sintéticos: max 3 kg.
Tejidos delicados: max 2 kg.
Lana: max 1,5 kg.
¿Cuánto pesa la ropa?
1 sábana 400/500 g
1 funda 150/200 g
1 mantel 400/500 g
1 albornoz 900/1.200 g
1 toalla 150/250 g
Prendas especiales
Cortinas: pliéguelas y colóquelas dentro de una
funda o de una bolsa de red. Lávelas solas sin
superar la media carga. Utilice el programa 6 que
excluye automáticamente el centrifugado.
Cazadoras acolchadas con plumas y
anoraks: si el relleno es de pluma de ganso o de
pato, se pueden lavar en la lavasecadora. Poner las
prendas del revés y realizar una carga máxima de
2-3 kg. repitiendo el enjuague una o dos veces y
utilizando el centrifugado delicado.
Lana: para obtener los mejores resultados, utilice
un detergente específico y no supere 1,5 kg. de
carga.
Detergentes y ropa
1
2
3
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
/