Makita VC002GL Používateľská príručka

VC002GL

VC004GL

EN Cordless Vacuum Cleaner INSTRUCTION MANUAL 9

PL Odkurzacz akumulatorowy INSTRUKCJA OBSŁUGI 23

HU Vezeték nélküli porszívó HASZNÁLATI KÉZIKÖNYV 39

SK Akumulátorový vysávač NÁVOD NA OBSLUHU 55

CS Bezdrátový akumulátorový

vysavač NÁVOD K OBSLUZE 69

UK Акумуляторний пилосос ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 83

RO Aspirator fără cablu MANUAL DE INSTRUCŢIUNI 99

DE Akku-Staubsauger BETRIEBSANLEITUNG 114

2

1

2

3

4

5

Fig.1

2

1

Fig.2

1

2

Fig.3

1

2

Fig.4

1

2

Fig.5

11

2

Fig.6

Fig.7

3

1

3

2

Fig.8

12

3

4

Fig.9

Fig.10

1

2

3

4

5

6

Fig.11

1

4

2

3

Fig.12

1

2

3

Fig.13

4

1

Fig.14

1

2

Fig.15

Fig.16

1

2

Fig.17

1

2

3

Fig.18

2

3

1

Fig.19

1

2

Fig.20

5

1

2

Fig.21

1

2

34

Fig.22

Fig.23

1

3

2

Fig.24

1

2

3

Fig.25

2

1

Fig.26

Fig.27

1

Fig.28

6

1

2

3

4

Fig.29

1

2

3

Fig.30

1

Fig.31

21

Fig.32

Fig.33

1

Fig.34

7

21

Fig.35

1

Fig.36

21

Fig.37

32

1

Fig.38

21

Fig.39

1

2

Fig.40

1

2

Fig.41

8

Fig.42

Fig.43

1

Fig.44

1

2

Fig.45

Fig.46

9ENGLISH

ENGLISH (Original instructions)

WARNING

• This machine is not intended for use by persons including children with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge.

• Children should be supervised to ensure that they do not play with the cleaner.

• See the chapter “SPECIFICATIONS” for the type reference of the battery.

• See the section “Installing or removing battery cartridge” for how to remove or install the battery.

• When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local

regulations relating to disposal of battery.

• If the tool is not used for a long period of time, the battery must be removed from the tool.

• Do not short the battery cartridge.

• See the chapter “MAINTENANCE” for the appropriate details of precautions during user maintenance.

SPECIFICATIONS

Model: VC002GL VC004GL

Standard lter type Powder lter (for dry dust)

Maximum air volume at the end of hose

(with BL4040, ø38 mm x 2.5 m hose) 2.7 m3/min

Maximum air volume at turbine

(with BL4040) 4.2 m3/min

Vacuum

(with BL4040) 23 kPa

Recoverable capacity 8 L 15 L

Dimensions (L x W x H) 366 mm x 334 mm x 425 mm 366 mm x 334 mm x 475 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 8.3 - 11.4 kg 8.6 - 11.7 kg

Protection degree IPX4

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications and battery cartridge may dier from country to country.

• The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight

of the appliance and battery cartridge(s) are shown in the table.

• For wet dust, the oat and the water lter or cloth lter are required.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040* / BL4050F* / BL4080F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Read instruction manual.

Take particular care and attention.

Warning! The cleaner may contain haz-

ardous dust.

Never stand on the cleaner.

Dust class L (light). The cleaners are capa-

ble of picking up dust class L. Follow your

country's regulations relating to dusts and

to occupational health and safety.

10 ENGLISH

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Intended use

The appliance is intended for collecting dry dust. The

appliance is suitable for commercial use, for example in

hotels, schools, hospitals, factories, shops, oces and

rental businesses.

Noise

The typical A-weighted noise level determined accord-

ing to EN60335-2-69:

Model VC002GL

Sound pressure level (LpA) : 70 dB(A) or less

Uncertainty (K) : 2.5 dB(A)

Model VC004GL

Sound pressure level (LpA) : 70 dB(A) or less

Uncertainty (K) : 2.5 dB(A)

The noise level under working may exceed 80 dB (A).

NOTE: The declared noise emission value(s) has

been measured in accordance with a standard test

method and may be used for comparing one tool with

another.

NOTE: The declared noise emission value(s)

may also be used in a preliminary assessment of

exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can dier from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN60335-2-69:

Model VC002GL

Vibration emission (ah,M) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

Model VC004GL

Vibration emission (ah,M) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can dier from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

o and when it is running idle in addition to the

trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

Cordless vacuum cleaner safety

warnings

WARNING: IMPORTANT! READ CAREFULLY

all safety warnings and all instructions BEFORE

USE. Failure to follow the warnings and instructions

may result in electric shock, re and/or serious injury.

1. Before use, make sure that this cleaner must

be used by people who have been adequately

instructed on the use of this cleaner.

2.

Before use, operators shall be provided with

information, instruction and training for the use

of the machine and the substances for which

it is to be used, including the safe method of

removal and disposal of the material collected.

3. Always make sure that lters are correctly

installed before use. Do not use the cleaner

without lters in place. Replace a damaged

lter immediately. It is recommended to have

some spares as lters are consumable items.

4. AVOID UNINTENTIONAL STARTING. Be sure

switch is OFF when installing battery(ies).

11 ENGLISH

5. Do not attempt to pick up ammable materials,

re works, lighted cigarettes, hot ashes, hot

metal chips, sharp materials such as razors,

needles, broken glass or the like.

6.

NEVER USE THE CLEANER IN THE VICINITY

OF GASOLINE, GAS, PAINT, ADHESIVES OR

OTHER HIGHLY EXPLOSIVE SUBSTANCES.

The switch emits sparks when turned ON and

OFF. And so does the motor commutator during

operation. A dangerous explosion may result.

7.

Never vacuum up toxic, carcinogenic, combusti-

ble or other hazardous materials such as asbes-

tos, arsenic, barium, beryllium, lead, pesticides,

or other health endangering materials.

8. Always place the cleaner on a horizontal at

surface to prevent it from falling or moving

unintentionally.

9. Never use the cleaner outdoors in the rain.

10. For Finland, this machine is not to be used

outdoors at low temperature.

11. Do not use close to heat sources (stoves, etc.).

12. If the exhaust air is returned to the room, it

is necessary to provide for an adequate air

change rate in the room. Reference to National

regulations is necessary.

13. Do not block suction inlet/outlet/cooling vents.

These vents permit cooling of the motor.

Blockage should be carefully avoided other-

wise the motor will burn out due to a lack of

ventilation.

14. Keep proper footing and balance at all times.

15. Do not fold, tug or step on the hose.

16. Stop the cleaner immediately if you notice

poor performance or anything abnormal

during operation.

17.

REMOVE THE BATTERY(IES). When not in use,

before servicing, and when changing accessories.

18. Clean and service the cleaner immediately

after each use to keep it in tiptop operating

condition.

19. MAINTAIN THE CLEANER WITH CARE. Keep

the cleaner clean for better and safer per-

formance. Follow instructions for changing

accessories. Keep handles dry, clean, and free

from oil and grease.

20. CHECK DAMAGED PARTS. Before further use

of the cleaner, a guard or other part that is

damaged should be carefully checked to deter-

mine that it will operate properly and perform

its intended function. Check for alignment of

moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tions that may aect its operation. A guard or

other part that is damaged should be properly

repaired or replaced by an authorized service

center unless otherwise indicated elsewhere

in this instruction manual. Have defective

switches replaced by authorized service cen-

ter. Don’t use the cleaner if switch does not

turn it on and o.

21. For user servicing, the machine shall be dis-

mantled, cleaned and serviced, as far as is

reasonably practicable, without causing risk to

the maintenance sta and others.

22. The machine should be technically inspected

by the manufacturer, or an instructed person,

at least annually, consisting of, for example,

inspection of lters for damage, air tightness

of the machine and proper function of the

control mechanism.

23. When carrying out service or repair opera-

tions, all contaminated items which cannot be

satisfactorily cleaned are to be disposed of;

such items shall be disposed of in impervious

bags in accordance with any current regula-

tion for the disposal of such waste.

24. REPLACEMENT PARTS. When servicing, use

only identical replacement parts.

25.

When not in use, always store the cleaner indoors.

26.

Be kind to your cleaner. Rough handling can cause

breakage of even the most sturdily built cleaner.

27. Do not attempt to clean the exterior or interior

with benzine, thinner or cleaning chemicals.

Cracks and discoloration may be caused.

28. Do not use cleaner in an enclosed space where

ammable, explosive or toxic vapors are given

o by oil-base paint, paint-thinner, gasoline,

some mothproong substances, etc., or in

areas where ammable dust is present.

29. Do not operate the cleaner or any tool while

under the inuence of drugs or alcohol.

30. As a basic rule of safety, use safety goggles or

safety glasses with side shields.

31. Use a dust mask in dusty work conditions.

32. This machine is not intended for use by per-

sons including children with reduced physical,

sensory or mental capabilities, or lack of expe-

rience and knowledge.

33. Children should be supervised to ensure that

they do not play with the cleaner.

34.

Never handle battery(ies) and cleaner with wet hands.

35. Use extreme caution when cleaning on stairs.

36. Do not use the cleaner as a stool or work

bench. The machine may fall down and may

result in personal injury.

37. Do not pick up foam or soapy liquid. It can

cause foam to come out of air exit, resulting in

electric shock and damage to the cleaner.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

12 ENGLISH

5. Do not use a battery pack or tool that is dam-

aged or modied. Damaged or modied batteries

may exhibit unpredictable behaviour resulting in

re, explosion or risk of injury.

6. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or tem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outside the specied range may damage the

battery and increase the risk of re.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10.

The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

13 ENGLISH

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the wire-

less unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50 °C (122 °F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart

pace makers are nearby.

7. Do not operate the wireless unit in places

where automated devices are nearby. If oper-

ated, automated devices may develop malfunction

or error.

8. Do not operate the wireless unit in places

under high temperature or places where

static electricity or electrical noise could be

generated.

9.

The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the user.

10. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

14. Always insert the wireless unit in the correct

direction.

15. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

16. Always close the lid of the slot when

operating.

17.

Do not remove the wireless unit from the slot

while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where

static electricity or electrical noise could be

generated.

21. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the

sun.

22. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas

could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

27. Do not use the tool with the lid of the slot dam-

aged. Water, dust, and dirt come into the slot may

cause malfunction.

28. Do not pull and/or twist the lid of the slot more

than necessary. Restore the lid if it comes o

from the tool.

29. Replace the lid of the slot if it is lost or

damaged.

SAVE THESE INSTRUCTIONS.

PARTS DESCRIPTION

► Fig.1: 1. Head unit 2. Powder lter (HEPA)

3. Damper 4. Prelter 5. Tank

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the appliance

is switched o and the battery cartridges are

removed before adjusting or checking function on

the appliance.

Installing or removing battery

cartridge

CAUTION: Always switch o the appliance

before installing or removing battery cartridges.

CAUTION: Hold the cleaner and battery car-

tridges rmly when installing or removing battery

cartridges. Failure to do so may cause them to slip

o your hands, resulting in damage to the cleaner and

battery cartridges or personal injury.

CAUTION: Be careful not to pinch your n-

gers when opening or closing the battery cover.

Failure to do so may cause personal injury.

The cleaner has double battery slots. With two identical

batteries in parallel, you can extend your running time

in one or more uses without having to stop to recharge

batteries. The cleaner also works with a single battery,

so you can choose with either double batteries or single

battery according to your needs.

► Fig.2: 1. Left battery slot 2. Right battery slot

With double batteries

Continuous drive with two batteries allows longer run-

time and more ecient cleaning. When the rst battery

is becoming empty, the cleaner automatically switches

a power source, so it continues working with the second

battery.

14 ENGLISH

NOTE: The left battery slot (when facing the front of

the cleaner) has priority over the right battery slot.

The right battery slot will only be identied as a power

source, either when no battery is installed in the

left battery slot or the battery in the left battery slot

becomes empty.

NOTE: You can remove the battery from the left

battery slot and recharge it after the cleaner has

switched its power source from the left battery slot to

the right without ceasing operation. To give priority

back to the left battery slot after installing a recharged

battery, restart the cleaner.

With a single battery

Only one battery is required as a power source in either

the left or right battery slot. The cleaner automatically

determines which battery slot is available according to

operating conditions.

Installation and uninstallation

To install battery cartridges, release the lock rst,

and open the battery cover. Then insert the battery

cartridges.

► Fig.3: 1. Lock 2. Battery cover

Align the tongues on the battery cartridges with the

grooves in the battery housing and slip them into place.

Insert them all the way until they lock in place with a

little click.

Then lock the battery cover.

► Fig.4: 1. Battery cartridge 2. Button

To remove the battery cartridges, slide them out of the

battery housing while pressing and holding the buttons

in front of the cartridges.

CAUTION: Always install the battery cartridge

fully. If not, it may accidentally fall out of the appli-

ance, causing injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE: When the cleaner switches the power source

from the rst battery to the second, it may require a

temporary halt in operations, causing a slight loss of

suction. Please note that it is not malfunction so the

cleaner recovers and resumes operations immedi-

ately after the pause.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► Fig.5: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Battery indicators on control panel

The remaining battery capacity can be read on the

control panel at any time. Press the check button, and

the left and right indicators will show the battery charge

levels correspondingly.

► Fig.6: 1. Battery indicators 2. Check button

► Fig.7

Battery indicator status Remaining

battery

capacity

On O Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

Battery not

inserted

NOTE: The battery indicators will also be activated

when the cleaner starts functioning or switches its

power source from one to another.

15 ENGLISH

Appliance / battery protection

system

The appliance is equipped with an appliance/battery

protection system. This system automatically cuts o

power to the motor to extend appliance and battery life.

The appliance will automatically stop during operation

if the appliance or battery is placed under one of the

following conditions:

Overload protection

When the appliance/battery is operated in a manner

that causes it to draw an abnormally high current, the

appliance automatically stops. In this situation, turn the

appliance o and stop the application that caused the

appliance to become overloaded. Then turn the appli-

ance on to restart.

Overheat protection

On Blinking

When the appliance is overheated, the appliance stops

automatically, and both left and right battery indicators

blink. In this situation, let the appliance cool down

before turning the appliance on again.

On Blinking

When the battery is overheated, the appliance stops

automatically, and one of the indicators for overheated

battery blinks. In this situation, let the battery cool down

before turning the appliance on again.

Overdischarge protection

When the battery capacity becomes low, the appliance

stops automatically. If the appliance does not run along

with the switch operation, remove the batteries from the

appliance and recharge them.

Protections against other causes

Protection system is also designed for other causes that

could damage the appliance and allows the appliance to

stop automatically. Take all the following steps to clear

the causes, when the appliance has been brought to a

temporary halt or stop in operation.

1. Turn the appliance o, and then turn it on again to

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the appliance and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

Turning cleaner on

1. Turn the stand-by switch in the "I" (ON) or "AUTO"

(ON) position to have the cleaner ready in

stand-by mode.

2. Press the power button.

To switch back to stand-by mode, press the power

button again.

Turning cleaner o

Perform one of the following steps.

• Press the power button to set the cleaner back in

stand-by mode, and then turn the stand-by switch

in the "O" (OFF) position.

• Turn the stand-by switch in the "O" (OFF) position.

Adjusting suction power

The suction power can be adjusted according to your

work needs.

• Turn the suction force adjusting knob to the left to

reduce the suction power.

• Turn the suction force adjusting knob to the right

to increase the suction power.

► Fig.8: 1. Stand-by switch 2. Power button 3. Suction

force adjusting knob

Locking and unlocking casters

Rear casters can be locked with stoppers to help the

cleaner stand still.

Lower the stopper lever by hand to lock the caster, and

raise it up to release.

► Fig.9: 1. Caster 2. Stopper lever 3. Unlocked posi-

tion 4. Locked position

NOTE: When moving the cleaner, make sure that the

caster is unlocked. Moving the cleaner with the caster

in a locked position may cause damage to the caster.

Carriage handle

CAUTION: Lift and carry the appliance with

due care. Failing to do so may result in personal

injury or damage to the appliance.

When carrying the cleaner, carry it by holding the han-

dle on the head unit. The handle is retractable on the

head unit when not in use.

► Fig.10

16 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the appliance

is switched o and the battery cartridges are

removed before carrying out any work on the

appliance.

CAUTION: Always wear dust mask during

assembly or maintenance.

Installing powder lter (HEPA) and

prelter (for dry dust)

CAUTION: Never pick up water or other liq-

uids or wet dusts when using the powder lter.

Picking up such things may cause the powder lter

breakage.

To use powder lter:

1. Place the prelter into the tank aligning the mount-

ing position markings on the prelter and tank.

2. Set the damper into the prelter, and then place

the powder lter over the damper aligning the mounting

position markings on the powder lter and prelter.

3. Mount the head unit over the tank and secure

them with the locking latches.

► Fig.11: 1. Head unit 2. Powder lter (HEPA)

3. Damper 4. Prelter 5. Tank 6. Mounting

position marking

NOTICE: Before using the powder lter, make

sure that prelter and damper are used together. It

is not allowed to install powder lter alone.

Installing paper pack

Optional accessory

WARNING: Before using a paper pack, make

sure that the prelter is used together. Failure to

use the prelter together may cause unusual noise

and heat, resulting in a re.

NOTICE: Never pick up water or other liquids

or wet dusts when using a paper pack. Picking up

such things may cause the paper pack breakage.

NOTICE: Before using a paper pack, make sure

that the powder lter, damper and prelter are

always used together.

1. Unfold a paper pack.

2. Align the paper pack opening with the dust intake

of the tank.

3. Install the paper pack into the tank with its card-

board opening hooked on the paper pack holder.

► Fig.12: 1. Paper pack 2. Cardboard opening

3. Paper pack holder 4. Dust intake

Installing polyethylene bag

With a polyethylene bag installed in the tank, you can

easily empty the tank without letting your hands dirty.

Lay a polyethylene bag over the tank, and slip one side

of the top edge of the bag at its open end in between

the holder plate and the front wall of the tank.

► Fig.13: 1. Holder plate 2. Front wall of tank

3. Polyethylene bag

Spread the other top edges of the bag outwards over

the top rims of the tank. Place the prelter over the poly-

ethylene bag to fasten the opening of the bag securely.

► Fig.14: 1. Prelter

NOTE: A polyethylene bag available on the

market can be used. 0.04 mm or thicker one is

recommended.

NOTE: Too much dust will tear the bag easily, so

do not collect the dust more than the half of the bag

capacity.

Emptying tank with

polyethylene bag

WARNING: Always make sure that the cleaner

is switched o and the battery cartridges are

removed before emptying the tank. Failure to do

so may cause an electric shock and serious personal

injury.

NOTICE: Do not apply a great impact on the

tank. Applying a great impact may cause deformation

and damage to the parts.

NOTICE: Empty the tank at least once a day

although this depends on picked-up dust volume

in the tank. Or, the suction force will weaken and the

motor may be broken.

NOTICE: Do not grab the hooks or latches when

emptying the tank. Grabbing the hooks or latches

may cause them to break.

Release the locking latches and lift the head unit up o

the tank.

Shake o dust from the prelter before lifting the lter

away from the tank.

Then remove the polyethylene bag out of the tank,

closing the opening of the bag by hand.

► Fig.15: 1. Polyethylene bag 2. Tank

NOTE: Take the polyethylene bag out of the tank

carefully to avoid it from being scratched and torn by

the edges inside the tank.

NOTE: Empty the polyethylene bag before it

becomes full. Too much dust in the tank may cause

the polyethylene bag to be torn.

17 ENGLISH

Installing multi hook

Use the multi hook to hold a hose, accessories and

attachments not in use in place, and you can quickly

take them out according to your preferences.

► Fig.16

Place the multi hook over the mounting base at the rear

of the cleaner, setting the rails on the multi hook along

the grooves on the mounting base.

► Fig.17: 1. Multi hook 2. Mounting base

Installing MAKPAC adapter

Optional accessory

Connectable and stackable MAKPAC storage cases can be

installed on top of the cleaner with an optional adapter. The cases

are available in many sizes and styles to suit your preferences.

Place the mounting base hook over the handle of the

cleaner with its mounting surface facing upwards when

the handle is folded into the closed position.

► Fig.18:

1. Mounting base hook 2. Mounting surface 3. Handle

Mount the MAKPAC adapter onto the mounting base hook,

and secure them together with four screws provided.

► Fig.19: 1. MAKPAC adapter 2. Mounting base hook

3. Screw

Lift the push bar up and tighten the knob to prepare

installing the MAKPAC cases onto the cleaner.

► Fig.20: 1. Push bar 2. Knob

NOTE: For details on installing the MAKPAC cases,

refer to the instructions provided with the MAKPAC

adapter and cases.

Installing hose

NOTICE: Never force the hose for bending or

stamp it. Never move the cleaner by pulling the

hose. Forcing, stamping and pulling the hose may

cause a breakage or deformation of the hose.

NOTICE: When picking up large wastes such as

planer carvings, concrete dusts or similar other

than small wastes, use the 38 mm inner diameter

hose (optional accessory). Using the 28 mm inner

diameter hose (optional accessory) may cause a

hose stung and damage.

Connection to cleaner

Insert the hose end to the dust intake (hose inlet) of the

cleaner, then turn it clockwise until it locks in place.

► Fig.21: 1. Hose 2. Dust intake (hose inlet)

Connections with your work tools

(Country specic)

By connecting the vacuum cleaner to any available

work tools compatible with the cleaner, it works as a

dust extractor for your power tools.

Select one of the front cus or joints (optional acces-

sories) as most suitable for your tool model. Place the

cus or joint, as necessary, between the front end of the

cleaner hose and a dust extraction port of your tool.

► Fig.22: 1. Front cus or joint 2. Cleaner hose

3. Power tool 4. Vacuum cleaner

Installing or removing cleaner

attachments

CAUTION: After installing an attachment,

check if it is securely installed. If the attachment

is installed imperfectly, it may come o and cause

personal injury.

Attachments without lock function

Optional accessory

Insert an attachment into the suction inlet of the cleaner

by pushing and hand screwing it in place.

Hand twist and pull the attachment apart from the suc-

tion inlet after use.

► Fig.23

Attachments with lock function

Optional accessory

NOTICE: When installing the attachment with

lock function, be sure to align the release button

with the hook on the attachment. If they are not

aligned, the attachment will not be locked and may

come o from the cleaner.

Insert an attachment into the suction inlet of the cleaner

by pushing them together with a click.

To remove the attachment, pull it o while pushing the

release button.

► Fig.24: 1. Suction inlet with lock function 2. Release

button 3. Attachment with lock function

NOTE: An attachment with lock function can only be

installed in the suction inlet with lock function.

► Fig.25: 1. Attachment with lock function 2. Suction

inlet with lock function 3. Suction inlet with-

out lock function

Adjusting lengths of slide-type

extension wand

Optional accessory

A slide-type extension wand can be combined for

shorter and longer lengths. It allows to clean hard-to-

reach areas and comfortable positioning options.

Pull in and out the slide pipe to change wand lengths

while pressing and holding the slide button.

Release the slide button to lock the slide pipe in your

desired position.

► Fig.26: 1. Slide pipe 2. Slide button

18 ENGLISH

WIRELESS ACTIVATION

FUNCTION

What you can do with the wireless

activation function

The wireless activation function enables clean and

comfortable operation. By connecting a supported tool

to the cleaner, you can run the cleaner automatically

along with the switch operation of the tool.

► Fig.27

NOTICE: Be sure to refer to the instruction man-

ual of the tool when using the cleaner with wire-

less activation function.

NOTICE: Do not disassemble or tamper with the

wireless unit.

NOTICE: To prevent dust coming into the slot

of the wireless unit, always close the lid securely

during operation and storage.

NOTICE: Do not remove the wireless unit while

the power is being supplied. Doing so may cause a

malfunction of the wireless unit.

NOTICE: Do not press the wireless activation

button too hard and/or press the button with an

object with a sharp edge.

NOTE: Wireless activation needs Makita tools

equipped with the wireless unit.

NOTE: Prior to the initial use of the wireless activa-

tion function with each tool, the tool registration is

required. Once the registration is nished with the

tool, the re-registration is not required unless it is

cancelled.

NOTE: Before registration, be sure that the wireless

unit is properly inserted.

NOTE: One wireless unit can register up to 10 links

with other wireless units. If more than 10 other wire-

less units are registered to one wireless unit, the one

registered earliest will be cancelled automatically.

NOTE: The position of the wireless activation button

varies depending on the tool.

NOTE: The cleaner also starts by pressing the power

button when the stand-by switch is set to "AUTO".

However the power button will not actuate when the

wireless activation function is used.

Installing the wireless unit

CAUTION: Place the cleaner on a at and

stable surface when installing the wireless unit.

NOTICE:

Clean the dust and dirt on the cleaner

before installing the wireless unit. Dust or dirt may cause

malfunction if it comes into the slot of the wireless unit.

NOTICE:

To prevent the malfunction caused by

static, touch a static discharging material, such as

a metallic part, before picking up the wireless unit.

NOTICE: When installing the wireless unit,

always be sure that the wireless unit is inserted

in the correct direction and the lid is completely

closed.

1. Open the lid on the cleaner as shown in the gure.

► Fig.28: 1. Lid

2. Insert the wireless unit to the slot and then close

the lid.

When inserting the wireless unit, align the projections

with the recessed portions on the slot.

► Fig.29: 1. Wireless unit 2. Projection 3. Lid

4. Recessed portion

When removing the wireless unit, open the lid slowly.

The hooks on the back of the lid will lift the wireless unit

as you pull up the lid.

► Fig.30: 1. Wireless unit 2. Hook 3. Lid

After removing the wireless unit, keep it in the supplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the cleaner

NOTE: A Makita tool supporting the wireless activa-

tion function is required for the tool registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger on the tool or turn on the power switch

on the cleaner.

NOTE: Refer to the instruction manual of the tool, too.

If you wish to activate the cleaner along with the

switch operation of the tool, nish the tool registration

beforehand.

1. Install the wireless units to the cleaner and the

tool, respectively.

2. Install the batteries to the cleaner and the tool.

3. Set the stand-by switch on the cleaner to "AUTO".

► Fig.31: 1. Stand-by switch

4. Press the wireless activation button on the cleaner

for 3 seconds until the wireless activation lamp blinks in

green. And then press the wireless activation button on

the tool in the same way.

► Fig.32: 1. Wireless activation button 2. Wireless

activation lamp

19 ENGLISH

If the cleaner and the tool are linked successfully, the

wireless activation lamps will light up in green for 2

seconds and start blinking in blue.

NOTE: The wireless activation lamps nish blinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

less activation button briey and hold it down again.

NOTE: When performing two or more tool registration

for the cleaner, nish the tool registration one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the cleaner for

wireless activation.

NOTE: Always place the cleaner so that you can see

the status of the wireless activation lamp.

NOTE: Refer to the instruction manual of the tool, too.

After registering a tool to the cleaner, the cleaner will

automatically runs along with the switch operation of

the tool.

1. Install the wireless units to the cleaner and the

tool, respectively.

2. Install the batteries to the cleaner and the tool.

3. Connect the hose of the cleaner with the tool.

► Fig.33

4. Set the stand-by switch on the cleaner to "AUTO".

► Fig.34: 1. Stand-by switch

5. Push the wireless activation button on the tool

briey. The wireless activation lamp will blink in blue.

► Fig.35: 1. Wireless activation button 2. Wireless

activation lamp

6. Turn on the tool. Check if the cleaner runs while

the tool is operating.

CAUTION: Always check if the wireless acti-

vation function works before starting a work with

the tool.

To stop the wireless activation, push the wireless activa-

tion button on the tool, or set the stand-by switch on the

cleaner to "I" or "O".

NOTE: The wireless activation lamp on the tool will

stop blinking in blue when there is no operation for

2 hours. In this case, set the stand-by switch on the

cleaner to "AUTO" and press the wireless activation

button on the tool again.

NOTE: The cleaner starts/stops with a delay. There is

a time lag when the cleaner detects a switch opera-

tion of the tool.

NOTE: The transmission distance of the wireless unit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

cleaner, the cleaner may start running even if you do

not turn on the tool because other user is using the

wireless activation function.

Cancelling tool registration for the

cleaner

Perform the following procedure when cancelling the

tool registration for the cleaner.

1. Install the wireless units to the cleaner and the

tool, respectively.

2. Install the batteries to the cleaner and the tool.

3. Set the stand-by switch on the cleaner to "AUTO".

► Fig.36: 1. Stand-by switch

4. Press the wireless activation button on the cleaner

for 6 seconds. The wireless activation lamp blinks in

green and then become red. After that, press the wire-

less activation button on the tool in the same way.

► Fig.37: 1. Wireless activation button 2. Wireless

activation lamp

If the cancellation is performed successfully, the wire-

less activation lamps will light up in red for 2 seconds

and start blinking in blue.

NOTE: The wireless activation lamps nish blinking in

red after 20 seconds elapsed. Press the wireless acti-

vation button on the tool while the wireless activation

lamp on the cleaner is blinking. If the wireless acti-

vation lamp does not blink in red, push the wireless

activation button briey and hold it down again.

Erasing all tool registrations

You can erase all tool registrations from the cleaner as

follows.

► Fig.38: 1. Stand-by switch 2. Wireless activation

button 3. Wireless activation lamp

1. Install the wireless unit to the cleaner.

2. Install the batteries to the cleaner.

3. Set the stand-by switch to "AUTO".

4. Hold down the wireless activation button for about

6 seconds until the wireless activation lamp blinks in red

(about twice per one second).

5. When the wireless activation lamp starts blinking

in red, release your nger from the wireless activation

button. Thereafter, hold down the wireless activation

button again for about 6 seconds.

6. When the wireless activation lamp starts blinking

fast (about 5 times per one second) in red, release your

nger from the wireless activation button. When the

wireless activation lamp lights up in red and later lights

o, all tool registrations are erased.

NOTE: If the wireless activation lamp does not blink

in red, press the wireless activation button briey and

try again.

20 ENGLISH

Description of the wireless activation lamp status

► Fig.39: 1. Wireless activation button 2. Wireless

activation lamp

The wireless activation lamp shows the status of the wireless activation function. Refer to the below table for the

meaning of the lamp status.

Status Wireless activation lamp Description

Color

On

Blinking

Duration

(approximate)

Standby Blue Cleaner: con-

tinuing

Tool: 2 hours

Waiting for the tool registration or the wireless activation function

is available.

The lamp on the cleaner blinks when the stand-by switch is set in

AUTO. The lamp on the tool blinks when the wireless activation

button is pushed. The lamp on the tool will automatically turn o

when no operation is performed for 2 hours.

When the tool is

running.

The wireless activation of the cleaner is available and the tool is

running.

Tool

registration

Green 20 seconds Ready for the tool registration. Searching the tool to be registered.

2 seconds The tool registration has been nished. The wireless activation

lamp will start blinking in blue.

Cancelling/

erasing

tool

registration

Red

(slow: 2 times/sec.)

20 seconds Ready for the cancellation of the tool registration. Searching the

tool to be cancelled.

(fast: 5 times/sec.)

When the

wireless acti-

vation button is

pressed down.

Ready to erase all tool registrations.

2 seconds The tool registration has been cancelled/erased. The wireless

activation lamp will start blinking in blue.

Others Red 3 seconds The power is supplied to the wireless unit and the wireless activa-

tion function is starting up.

O - - The stand-by switch is not set to "AUTO".

Stránka sa načítava ...

Makita VC002GL Používateľská príručka

Makita VC002GL Používateľská príručka

V iných jazykoch

Súvisiace články