Makita M804 Používateľská príručka

Kategória
Elektrické náradie
Typ
Používateľská príručka

Táto príručka je tiež vhodná pre

GB Hammer Drill Instruction manual
ID Bor Palu Petunjuk penggunaan
VI Máy khoan búa Tài liu hng dn
TH
 
M804
M814
2
1 001691 2 001692
3 001693 4 01694
5 001695 6 001696
1
2
3
4
5
6
7
8
8
9
1
11
12
13
A
B
14
3
ENGLISH
Explanation of general view
SPECIFICATIONS
•Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
END201-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
..... Read instruction manual.
.............. DOUBLE INSULATION
ENE039-1
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.
ENF002-2
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
GEA005-3
General Power Tool Safety
Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while operating
a power tool.
Distractions can cause you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
1. Grip base
2. Side grip (auxiliary handle)
3. Teeth
4. Protrusion
5. Loosen
6. Tighten
7. Drill chuck
8. Chuck key
9. Side grip
10. Depth gauge
11. Switch trigger
12. Lock button
13. Reversing switch lever
14. Action mode changing lever
Model M804 M814
Capacities
Concrete 16 mm 13 mm
Wood 30 mm 18 mm
Steel 13 mm 13 mm
No load speed (min
-1
) 0 - 3,000 0 - 2,800
Blows per minute 0 - 45,000 0 - 30,800
Overall length 297 mm 272 mm
Net weight 2.0 kg 1.6 kg
Safety class /II
4
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
12. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
13. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
17. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
19. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
20. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
21. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
22. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
26. Follow instruction for lubricating and changing
accessories.
27. Keep handles dry, clean and free from oil and
grease.
GEB003-5
HAMMER DRILL SAFETY
WARNINGS
1. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
4. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
5. Hold the tool firmly with both hands.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the bit or the workpiece immediately
after operation; they may be extremely hot and
could burn your skin.
9. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
5
ASSEMBLY
Installing side grip (auxiliary handle)
(Fig. 1)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip.
Always use the side grip to ensure operating safety. Install
the side grip so that the teeth on the grip fit in between the
protrusions on the tool barrel. Then tighten the grip by
turning clockwise at the desired position. It may be swung
360° so as to be secured at any position.
Installing or removing drill bit (Fig. 2)
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten
all three chuck holes evenly. To remove the bit, turn the
chuck key counterclockwise in just one hole, then loosen
the chuck by hand.
After using the chuck key, be sure to return it to the
original position.
Depth gauge (optional accessory) (Fig. 3)
The depth gauge is convenient for drilling holes of uniform
depth. Loosen the side grip and insert the depth gauge
into the hole in the grip base. Adjust the depth gauge to
the desired depth and tighten the side grip.
NOTE:
•The depth gauge cannot be used at the position where
the depth gauge strikes against the gear housing.
FUNCTIONAL DESCRIPTION
Switch action (Fig. 4)
CAUTION:
•Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop. For continuous
operation, pull the switch trigger and then push in the lock
button. To stop the tool from the locked position, pull the
switch trigger fully, then release it.
Reversing switch action (Fig. 5)
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the position
(A side) for clockwise rotation or to the position (B side)
for counterclockwise rotation.
CAUTION:
•Always check the direction of rotation before operation.
•Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
Selecting the action mode (Fig. 6)
This tool has an action mode change lever. For rotation
with hammering, slide the action mode change lever to
the right ( symbol). For rotation only, slide the action
mode change lever to the left ( symbol).
CAUTION:
•Always slide the action mode change lever all the way
to your desired mode position. If you operate the tool
with the lever positioned halfway between the mode
symbols, the tool may be damaged.
OPERATION
Hammer drilling operation
When drilling in concrete, granite, tile, etc., slide the action
mode change lever to the position of symbol to use
"rotation with hammering" action. Be sure to use a
tungsten-carbide tipped bit. Do not apply more pressure
when the hole becomes clogged with chips or particles.
Instead, run the tool at an idle, then remove the bit
partially from the hole. By repeating this several times, the
hole will be cleaned out.
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Drilling operation
When drilling in wood, metal or plastic materials, slide the
action mode change lever to the position of symbol to
use "rotation only" action.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workplace.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the
point to be drilled. Place the point of the bit in the
indentation and start drilling. Use a cutting lubricant when
drilling metals. The exceptions are iron and brass which
should be drilled dry.
CAUTION:
•Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
•There is a tremendous force exerted on the tool/bit at
the time of hole break through. Hold the tool firmly and
exert care when the bit begins to break through the
workplace.
•A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you do
not hold it firmly.
•Always secure small workplaces in a vise or similar
hold-down device.
6
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
•Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by an
Makita Authorized Service Center.
7
BAHASA INDONESIA
Penjelasan tampilan keseluruhan
SPESIFIKASI
•Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat
berubah tanpa pemberitahuan.
•Spesifikasi dapat berbeda dari satu negara ke negara lainnya.
END201-5
Simbol
Berikut ini adalah simbol-simbol yang digunakan pada
peralatan ini.
Pastikan Anda mengerti makna masing-masing simbol
sebelum menggunakan alat.
..... Baca petunjuk penggunaan.
.............. ISOLASI GANDA
ENE039-1
Penggunaan
Mesin ini digunakan untuk membor kejut batu bata, beton
dan batu serta juga untuk membor tanpa kejut kayu,
logam, keramik dan plastik.
ENF002-2
Pasokan daya
Mesin harus terhubung dengan pasokan daya listrik yang
bervoltase sama dengan yang tertera pada pelat nama,
dan hanya dapat dijalankan dengan listrik AC fase
tunggal. Mesin diisolasi ganda dan oleh sebab itu dapat
dihubungkan dengan soket tanpa arde.
GEA005-3
Peringatan Keselamatan Umum
Mesin Listrik
PERINGATAN! Bacalah semua peringatan
keselamatan dan semua petunjuk. Kelalaian mematuhi
peringatan dan petunjuk dapat menyebabkan sengatan
listrik, kebakaran dan/atau cedera serius.
Simpanlah semua peringatan dan
petunjuk untuk acuan di masa
depan.
Istilah “mesin listrik” dalam semua peringatan mengacu
pada mesin listrik yang dijalankan dengan sumber listrik
jala-jala (berkabel) atau baterai (tanpa kabel).
Keselamatan tempat kerja
1. Jaga tempat kerja selalu bersih dan
berpenerangan cukup. Tempat kerja yang
berantakan dan gelap mengundang kecelakaan.
2. Jangan gunakan mesin listrik dalam lingkungan
yang mudah meledak, misalnya jika ada cairan,
gas, atau debu yang mudah menyala. Mesin listrik
menimbulkan bunga api yang dapat menyalakan debu
atau uap tersebut.
3. Jauhkan anak-anak dan orang lain saat
menggunakan mesin listrik. Bila perhatian terpecah,
anda dapat kehilangan kendali.
Keamanan kelistrikan
4. Steker mesin listrik harus cocok dengan
stopkontak. Jangan sekali-kali mengubah steker
dengan cara apa pun. Jangan menggunakan
steker adaptor dengan mesin listrik berarde
(dibumikan). Steker yang tidak diubah dan
stopkontak yang cocok akan mengurangi risiko
sengatan listrik.
5. Hindari sentuhan tubuh dengan permukaan
berarde atau yang dibumikan seperti pipa,
radiator, kompor, dan kulkas. Risiko sengatan listrik
bertambah jika tubuh Anda terbumikan atau terarde.
6. Jangan membiarkan mesin listrik kehujanan atau
kebasahan. Air yang masuk ke dalam mesin listrik
akan meningkatkan risiko sengatan listrik.
1. Alas gagang
2.
Gagang sisi (pegangan tambahan)
3. Gigi-gigi
4. Tonjolan
5. Kendurkan
6. Kencangkan
7. Cekam bor
8. Kunci cekam
9. Gagang sisi
10. Pengukur kedalaman
11. Picu saklar
12. Tombol kunci
13. Tuas saklar pembalik arah
14. Tuas pengubah mode kerja
Model M804 M814
Kapasitas
Beton 16 mm 13 mm
Kayu 30 mm 18 mm
Baja 13 mm 13 mm
Kecepatan tanpa beban (min
-1
) 0 - 3.000 0 - 2.800
Hembusan per menit 0 - 45.000 0 - 30.800
Panjang keseluruhan 297 mm 272 mm
Berat bersih 2,0 kg 1,6 kg
Kelas keamanan /II
8
7. Jangan menyalahgunakan kabel. Jangan sekali-
kali menggunakan kabel untuk membawa,
menarik, atau mencabut mesin listrik dari
stopkontak. Jauhkan kabel dari panas, minyak,
tepian tajam, atau bagian yang bergerak. Kabel
yang rusak atau kusut memperbesar risiko sengatan
listrik.
8. Bila menggunakan mesin listrik di luar ruangan,
gunakan kabel ekstensi yang sesuai untuk
penggunaan di luar ruangan. Penggunaan kabel
yang sesuai untuk penggunaan luar ruangan
mengurangi risiko sengatan listrik.
9. Jika mengoperasikan mesin listrik di lokasi
lembap tidak terhindarkan, gunakan pasokan daya
yang dilindungi peranti imbasan arus (residual
current device - RCD). Penggunaan RCD
mengurangi risiko sengatan listrik.
10. Penggunaan pasokan daya melalui RCD dengan
kapasitas arus sisa 30 mA atau kurang selalu
dianjurkan.
Keselamatan diri
11. Jaga kewaspadaan, perhatikan pekerjaan Anda
dan gunakan akal sehat bila menggunakan mesin
listrik. Jangan menggunakan mesin listrik saat
Anda lelah atau di bawah pengaruh obat bius,
alkohol, atau obat. Sekejap saja lalai saat
menggunakan mesin listrik dapat menyebabkan
cedera diri yang serius.
12. Gunakan alat pelindung diri. Selalu gunakan
pelindung mata. Peralatan pelindung seperti masker
debu, sepatu pengaman anti-selip, helm pengaman,
atau pelindung telinga yang digunakan untuk kondisi
yang sesuai akan mengurangi risiko cedera diri.
13. Cegah penyalaan yang tidak disengaja. Pastikan
bahwa sakelar berada dalam posisi mati (off)
sebelum menghubungkan mesin ke sumber daya
dan/atau baterai, atau mengangkat atau
membawanya. Membawa mesin listrik dengan jari
Anda pada sakelarnya atau mengalirkan listrik pada
mesin listrik yang sakelarnya hidup (on) akan
mengundang kecelakaan.
14. Lepaskan kunci-kunci penyetel sebelum
menghidupkan mesin listrik. Kunci-kunci yang
masih terpasang pada bagian mesin listrik yang
berputar dapat menyebabkan cedera.
15. Jangan meraih terlalu jauh. Jagalah pijakan dan
keseimbangan sepanjang waktu. Hal ini
memungkinkan kendali yang lebih baik atas mesin
listrik dalam situasi yang tidak diharapkan.
16. Kenakan pakaian dengan baik. Jangan memakai
pakaian yang kedodoran atau perhiasan. Jaga
jarak antara rambut, pakaian, dan sarung tangan
Anda dengan bagian mesin yang bergerak.
Pakaian kedodoran, perhiasan, atau rambut panjang
dapat tersangkut pada bagian yang bergerak.
17. Jika tersedia fasilitas untuk menghisap dan
mengumpulkan debu, pastikan fasilitas tersebut
terhubung listrik dan digunakan dengan baik.
Penggunaan pembersih debu dapat mengurangi
bahaya yang terkait dengan debu.
Penggunaan dan pemeliharaan mesin listrik
18. Jangan memaksa mesin listrik. Gunakan mesin
listrik yang tepat untuk keperluan Anda. Mesin
listrik yang tepat akan menuntaskan pekerjaan
dengan lebih baik dan aman pada kecepatan sesuai
rancangannya.
19. Jangan gunakan mesin listrik jika sakelar tidak
dapat menyalakan dan mematikannya. Mesin listrik
yang tidak dapat dikendalikan dengan sakelarnya
adalah berbahaya dan harus diperbaiki.
20. Cabut steker dari sumber listrik dan/atau baterai
dari mesin listrik sebelum melakukan penyetelan,
penggantian aksesori, atau menyimpan mesin
listrik. Langkah keselamatan preventif tersebut
mengurangi risiko hidupnya mesin secara tak
sengaja.
21. Simpan mesin listrik jauh dari jangkauan anak-
anak dan jangan biarkan orang yang tidak paham
mengenai mesin listrik tersebut atau petunjuk ini
menggunakan mesin listrik. Mesin listrik sangat
berbahaya di tangan pengguna yang tak terlatih.
22. Rawatlah mesin listrik. Periksa apakah ada bagian
bergerak yang tidak lurus atau macet, bagian yang
pecah dan kondisi lain yang dapat mempengaruhi
penggunaan mesin listrik. Jika rusak, perbaiki
dahulu mesin listrik sebelum digunakan. Banyak
kecelakaan disebabkan oleh kurangnya pemeliharaan
mesin listrik.
23. Jaga agar mesin pemotong tetap tajam dan bersih.
Mesin pemotong yang terawat baik dengan mata
pemotong yang tajam tidak mudah macet dan lebih
mudah dikendalikan.
24. Gunakan mesin listrik, aksesori, dan mata mesin,
dll. sesuai dengan petunjuk ini, dengan
memperhitungkan kondisi kerja dan jenis
pekerjaan yang dilakukan. Penggunaan mesin listrik
untuk penggunaan yang lain dari peruntukan dapat
menimbulkan situasi berbahaya.
Servis
25. Berikan mesin listrik untuk diperbaiki hanya
kepada oleh teknisi yang berkualifikasi dengan
menggunakan hanya suku cadang pengganti yang
serupa.
Hal ini akan menjamin terjaganya keamanan
mesin listrik.
26. Patuhi petunjuk pelumasan dan penggantian
aksesori.
27. Jagalah agar gagang kering, bersih, dan bebas
dari minyak dan gemuk.
GEB003-5
PERINGATAN KESELAMATAN
BOR PALU
1.
Kenakan pelindung telinga saat melakukan
pengeboran tumbuk (impact drilling).
Terpaan
kebisingan dapat menyebabkan hilangnya
pendengaran.
2. Gunakan gagang tambahan, jika disertakan
bersama mesin ini. Kehilangan kendali dapat
menyebabkan cedera.
3. Pegang mesin listrik pada permukaan genggam
yang terisolasi saat melakukan pekerjaan bila
mesin pemotong mungkin bersentuhan dengan
kawat tersembunyi atau kabelnya sendiri. Aksesori
pemotong yang menyentuh kawat “hidup” dapat
menyebabkan bagian logam pada mesin teraliri arus
listrik dan menyengat pengguna.
9
4. Selalu pastikan Anda berdiri di atas alas yang
kuat.
Pastikan tidak ada orang di bawahnya bila Anda
menggunakan mesin di tempat tinggi.
5. Pegang mesin kuat-kuat dengan kedua tangan.
6. Jauhkan tangan dari bagian yang berputar.
7. Jangan tinggalkan mesin dalam keadaan hidup.
Jalankan mesin hanya ketika digenggam tangan.
8. Jangan menyentuh mata mesin atau benda kerja
segera setelah pengoperasian; suhunya mungkin
masih sangat panas dan dapat membakar kulit
Anda.
9. Bahan tertentu mengandung zat kimia yang
mungkin beracun. Hindari menghirup debu dan
persentuhan dengan kulit. Ikuti data keselamatan
bahan dari pemasok.
SIMPAN PETUNJUK INI.
PERINGATAN:
JANGAN biarkan kenyamanan atau terbiasanya Anda
dengan produk (karena penggunaan berulang)
menggantikan kepatuhan yang ketat terhadap aturan
keselamatan untuk produk yang terkait.
PENYALAHGUNAAN atau kelalaian mematuhi kaidah
keselamatan yang tertera dalam petunjuk ini dapat
menyebabkan cedera badan serius.
PERAKITAN
Memasang gagang sisi
(pegangan tambahan) (Gb. 1)
PERHATIAN:
Pastikan mesin dalam keadaan mati dan steker telah
dicabut sebelum memasang atau melepas gagang sisi.
Gunakan selalu gagang sisi untuk menjamin keselamatan
penggunaan. Pasang gagang sisi sedemikian rupa
hingga gigi-gigi pada gagang bertemu dengan tonjolan
pada silinder mesin. Lalu kencangkan gagang dengan
memutar searah jarum jam ke posisi yang diinginkan.
Gagang dapat diputar 360° agar dapat ditahan di posisi
mana saja.
Memasang atau melepas mata bor (Gb. 2)
PERHATIAN:
•Pastikan bahwa mesin dalam keadaan mati dan steker
tercabut sebelum memasang atau melepas mata bor.
Untuk memasang mata bor, masukkan mata bor ke dalam
cekam sejauh mungkin. Kencangkan cekam dengan
tangan. Masukkan kunci cekam ke dalam tiga lubang
yang ada dan kencangkan searah jarum jam. Pastikan
ketiga lubang cekam dikencangkan secara seragam.
Untuk melepas mata bor, putar kunci cekam berlawanan
arah jarum jam pada satu lubang saja, lalu bebaskan
mata bor dengan tangan.
Setelah menggunakan kunci cekam, pastikan untuk
mengembalikannya ke posisi semula.
Pengukur kedalaman (pilihan aksesori)
(Gb. 3)
Pengukur kedalaman sangat tepat digunakan untuk
menghasilkan lubang-lubang pengeboran dengan
kedalaman yang seragam. Kendurkan gagang sisi dan
masukkan pengukur kedalaman ke dalam lubang pada
alas gagang. Sesuaikan pengukur kedalaman pada
kedalaman yang diinginkan dan kencangkan gagang sisi.
CATATAN:
•Pengukur kedalaman tidak bisa digunakan bila
posisinya berlawanan dengan rumahan gir.
DESKRIPSI FUNGSI
Kerja saklar (Gb. 4)
PERHATIAN:
Sebelum memasukkan steker, pastikan picu saklar berfungsi
dengan baik dan kembali ke posisi "OFF" saat dilepas.
Untuk menjalankan mesin, cukup tarik picu saklarnya.
Kecepatan mesin akan meningkat dengan menambah
tekanan pada picu saklar. Lepaskan picu saklar untuk
berhenti. Untuk penggunaan terus-menerus, tarik picu
saklar kemudian tekan tombol kunci. Untuk melepaskan
mesin dari posisi terkunci, tarik picu saklar sepenuhnya
kemudian lepaskan.
Kerja saklar pembalik arah (Gb. 5)
Mesin ini memiliki saklar pembalik arah untuk mengubah
arah putaran. Gerakkan tuas saklar pembalik arah ke
posisi
(sisi A) untuk putaran searah jarum jam atau
posisi
(sisi B) untuk putaran berlawanan arah jarum jam.
PERHATIAN:
•Selalu periksa arah putaran sebelum penggunaan.
•Gunakan saklar pembalik arah hanya setelah mesin
berhenti penuh. Mengubah arah putaran sebelum
mesin berhenti dapat merusak mesin.
Memilih mode kerja (Gb. 6)
Mesin ini memiliki tuas pengubah mode kerja. Untuk
putaran dengan getar, geser tuas pengubah mode kerja
ke kanan (simbol ). Untuk putaran saja, geser tuas
pengubah mode kerja ke kiri (simbol ).
PERHATIAN:
Selalu geser tuas pengubah mode kerja hingga penuh
ke posisi yang anda inginkan. Jika anda memakai alat
dengan tuas berada di posisi tengah antara kedua
simbol mode alat bisa rusak.
PENGGUNAAN
Cara pengoperasian bor getar
Saat mengebor beton, granit, ubin, dll. geser tuas
pengubah mode kerja ke posisi bersimbol untuk
gerakan putar dengan getaran. Pastikan Anda
menggunakan mata bor berujung tungsten-carbide.
Jangan menambah tekanan bila lubang dipenuhi geram-
geram atau partikel. Tetapi, nyalakan alat tanpa putaran,
lalu angkat mata bor sedikit dari lubang. Dengan
mengulanginya beberapa kali, lubang akan bersih.
Setelah mengebor lubang, gunakan penghembus angin
untuk membersihkan lubang dari debu.
10
Pekerjaan pengeboran
Bila mengebor bahan kayu, logam atau plastik, geser tuas
pengubah mode kerja ke posisi bersimbol untuk
menggunakan hanya "putaran saja".
Mengebor kayu
Saat mengebor kayu, hasil terbaik didapat dengan bor
kayu yang dilengkapi sekrup pemandu. Sekrup pemandu
memudahkan pengeboran dengan menarik mata bor ke
benda kerja.
Mengebor logam
Untuk mencegah mata bor selip ketika mulai membuat
lubang, buatlah takik dengan penitik lalu palu pada titik
yang akan dibor. Letakkan ujung mata bor pada takik dan
mulailah mengebor. Gunakan cairan pendingin saat
mengebor logam. Pengecualian untuk besi dan kuningan
yang harus dibor kering.
PERHATIAN:
•Menekan mesin secara berlebihan tidak akan
mempercepat pengeboran. Bahkan, tekanan yang
berlebihan hanya akan merusak mata bor Anda,
mengurangi kinerja mesin dan memperpendek usia
pakai mesin.
•Akan timbul gaya yang sangat kuat pada mesin/mata
bor saat menembus lubang. Pegang mesin dengan
kuat dan berhati-hatilah saat mata bor menembus
benda kerja.
•Mata bor yang macet dapat dicabut dengan menyetel
saklar pembalik arah agar mesin berputar berlawanan
arah untuk mundur. Tetapi, mesin bisa saja mundur
mendadak jika Anda tidak memegangnya dengan kuat.
Tahan benda kerja berukuran kecil dengan penjepit
atau alat penahan lain.
PERAWATAN
PERHATIAN:
•Pastikan bahwa mesin dalam keadaan mati dan steker
tercabut sebelum melakukan pekerjaan apapun pada
mesin.
•Jangan sekali-kali menggunakan bensin, tiner, alkohol,
atau bahan sejenisnya. Penggunaan bahan demikian
dapat menyebabkan perubahan warna, perubahan
bentuk atau timbulnya retakan.
Untuk menjaga keamanan dan keandalan alat, perbaikan,
perawatan atau penyetelan harus dilakukan oleh Pusat
Layanan Resmi Makita.
11
TING VIT
Gii thích v hình v tng th
THÔNG S K THUT
•Do chng trình nghiên cu và phát trin liên tc ca chúng tôi nên các thông s k thut trong ây có th thay i mà
không cn thông báo trc.
•Các thông s k thut có th thay i tùy theo tng quc gia.
END201-5
Ký hiu
Phn di ây cho bit các ký hiu c dùng cho thit b.
m bo rng bn hiu rõ ý ngha ca các ký hiu này
trc khi s dng.
..... c tài liu hng dn.
.............. CÁCH IN KÉP
ENE039-1
Mc ích s dng
Dng c này c thit k cho vic khoan óng vào gch,
bê-tông, á cng nh cho vic khoan không cn óng vào
g, kim loi, gm và nha.
ENF002-2
Ngun cp in
Dng c này ch c ni vi ngun cp in có in áp
ging nh ã ch ra trên bin tên và ch có th c vn
hành trên ngun in AC mt pha. Chúng c cách in
hai lp và do ó cng có th c s dng vi các cm
in không có dây tip t.
GEA005-3
Cnh báo An toàn Chung dành
cho Dng c Máy
CNH BÁO! c tt c các cnh báo an toàn và
hng dn. Vic không tuân theo các cnh báo và
hng dn có th dn n in git, ho hon và/hoc
thng tích nghiêm trng.
Lu gi tt c cnh báo hng
dn  tham kho sau này.
Thut ng “dng c máy” trong các cnh báo  cp n
dng c máy (có dây) c vn hành bng ngun in
chính hoc dng c máy (không dây) c vn hành
bng pin ca bn.
An toàn ti ni làm vic
1. Gi ni làm vic sch s và có  ánh sáng. Ni
làm vic ba bn hoc ti thng d gây ra tai nn.
2. Không vn hành dng c máy trong môi tr
ng
cháy n, ví d nh môi trng có s hin din
ca các cht lng, khí hoc bi d cháy. Các dng
c máy to tia la in có th làm bi hoc khí bc
cháy.
3. Gi tr em và ngi ngoài tránh xa ni làm vic
khi ang vn hành dng c máy. S xao lãng có th
khin bn mt kh nng kim soát.
An toàn v in
4. Phích c
m ca dng c máy phi khp vi cm.
Không bao gi c sa i phích cm theo bt
k cách nào. Không s dng bt k phích chuyn
i nào vi các dng c máy c ni t (tip
t). Các phích cm còn nguyên vn và cm phù
hp s gim nguy c in git.
5. Tránh  c th tip xúc vi các b m
t ni t
hoc tip t nh ng ng, b tn nhit, bp ga
và t lnh. Nguy c b in git s tng lên nu c
th bn c ni t hoc tip t.
6. Không  dng c máy tip xúc vi ma hoc
trong iu kin m t. Nc lt vào dng c
máy
s làm tng nguy c in git.
1.  tay cm
2. Tay cm hông (tay cm ph)
3. Rng
4. Phn nhô ra
5. Vn lng
6. Vn cht
7. Ngàm khoan
8. Khóa ngàm
9. Tay cm hông
10. Thanh o sâu
11. Cn công tc khi ng
12. Nút khóa
13. Cn công tc o chiu
14. Cn thay i ch  hot ng
KiuM804M814
Công sut
Bê-tông 16 mm 13 mm
G 30 mm 18 mm
Thép 13 mm 13 mm
Tc  không ti (phút
-1
) 0 - 3.000 0 - 2.800
S nhát mi phút 0 - 45.000 0 - 30.800
Chiu dài tng th 297 mm 272 mm
Trng lng tnh 2,0 kg 1,6 kg
Cp  an toàn /II
12
7. Không lm dng dây. Không bao gi s dng dây
 mang, kéo hoc tháo phích cm dng c máy.
Gi dây tránh xa ngun nhit, du, các mép sc
hoc các b phn chuyn ng. Dây b hng hoc
b ri s làm tng nguy c in git.
8. Khi vn hành dng c máy ngoài tri, hãy s
dng dây kéo dài phù hp cho vic s dng ngoài
tri. Vic dùng dây phù hp cho vi
c s dng ngoài
tri s gim nguy c in git.
9. Nu bt buc phi vn hành dng c máy ni
m t, hãy s dng ngun cp in c bo v
bng thit b ngt dòng in rò (RCD). Vic s
dng RCD s gim nguy c in git.
10. Chúng tôi luôn khuyên bn s d
ng ngun cp
in qua thit b RCD có th ngt dòng in d
nh mc 30 mA hoc thp hn.
An toàn cá nhân
11. Luôn tnh táo, quan sát nhng vic bn ang làm
và s dng nhng phán oán theo kinh nghim
khi vn hành dng c máy. Không s dng dng
c máy khi bn ang mt mi hoc chu nh
hng ca ma tuý, ru hay thuc. Ch m
t
khonh khc không tp trung khi ang vn hành dng
c máy cng có th dn n thng tích cá nhân
nghiêm trng.
12. S dng thit b bo h cá nhân. Luôn eo thit b
bo v mt. Các thit b bo h nh mt n chng
bi, giày an toàn chng trt, m bo h hay thit b
bo v thính giác c s d
ng trong các iu kin
thích hp s giúp gim thng tích cá nhân.
13. Tránh vô tình khi ng dng c máy. m bo
công tc v trí off (tt) trc khi ni ngun in
và/hoc b pin, cm hoc mang dng cy. Vic
mang dng c máy khi ang t ngón tay v trí công
tc hoc cp in cho dng c máy ang bt thng
d
gây ra tai nn.
14. Tháo mi khoá hoc chìa vn iu chnh trc khi
bt dng c máy. Vic chìa vn hoc khoá vn còn
gn vào b phn quay ca dng c máy có th dn
n thng tích cá nhân.
15. Không vi quá cao. Luôn gi thng bng tt và có
ch  chân phù hp. iu này cho phép iu khin
dng c máy tt hn trong nhng tình hung bt ng
.
16.
n mc phù hp. Không mc qun áo rng hay
eo  trang sc. Gi tóc, qun áo và gng tay
tránh xa các b phn chuyn ng.
Qun áo rng,
 trang sc hay tóc dài có th mc vào các b phn
chuyn ng.
17. Nu các thit b c cung cp  kt ni các thit
b thu gom và hút bi, hãy m bo chúng c
kt ni và s dng hp lý. Vic s dng thit b thu
gom bi có th làm gim nhng mi nguy him liên
quan n bi.
S dng và bo qun dng c máy
18. Không dùng lc i vi dng c máy. S dng
úng dng c máy cho công vic ca bn. S
dng úng dng c máy s giúp thc hin công vic
tt hn và an toàn hn theo giá tr nh mc c
thit k ca dng c máy ó.
19. Không s dng dng c máy nu công tc không
bt và tt c dng c máy ó. Mi dng c máy
không th iu khi
n c bng công tc u rt
nguy him và cn c sa cha.
20. Rút phích cm ra khi ngun in và/hoc ngt
kt ni b pin khi dng c máy trc khi thc
hin bt k công vic iu chnh, thay i ph
tùng hay ct gi dng c máy nào. Nhng bin
pháp an toàn phòng nga này s gim nguy c
tình khi 
ng vô tình dng c máy.
21. Ct gi các dng c máy không s dng ngoài
tm vi ca tr em không cho bt k ngi nào
không có hiu bit v dng c máy hoc các
hng dn này vn hành dng c máy. Dng c
máy s rt nguy him nu c s dng bi nhng
ngi dùng cha qua ào to.
22. Bo qun dng c máy. Ki
m tra tình trng lch
trc hoc bó kp ca các b phn chuyn ng,
hin tng nt v ca các b phn và mi tình
trng khác mà có th nh hng n hot ng
ca dng cy. Nu có hng hóc, hãy sa cha
dng c máy trc khi s dng. Nhiu tai nn xy
ra là do không bo qun tt dng c máy.
23. Luôn gi
cho dng c ct c sc bén và sch
s. Nhng dng c ct c bo qun tt có mép ct
sc s ít b kt hn và d iu khin hn.
24. S dng dng c máy, ph tùng và u dng c
ct, v.v... theo các hng dn này, có tính n iu
kin làm vic và công vic c thc hin.
Vic s
dng dng c máy cho các công vic khác vi công
vic d nh có th gây nguy him.
Bo dng
25.  nhân viên sa cha  trình  bo dng
dng c máy ca bn và ch s dng các b phn
thay th ng nht. Vic này s m bo duy trì
c  an toàn ca dng c máy.
26. Tuân theo hng dn dành cho vic bôi tr
n và
thay ph tùng.
27. Gi tay cm khô, sch, không dính du và m.
GEB003-5
CNH BÁO AN TOÀN DÀNH CHO
KHOAN BÚA
1. eo thit b bo v tai khi khoan. Vic  tai tip xúc
vi ting n có th gây gim thính lc.
2. S dng (các) tay cm ph, nu c cung cp
cùng vi dng c. Vic mt kh nng kim soát có
th dn n thng tích cá nhân.
3. Cm dng c máy bng b mt kp cách in khi
thc hin mt thao tác trong
ó b phn ct có th
tip xúc vi dây dn kín hoc dây ca chính nó. B
phn ct tip xúc vi dây dn “có in” có th khin
các b phn kim loi b h ca dng c máy “in”
và làm cho ngi vn hành b in git.
4. Luôn m bo bn có ch t chân vng chc.
m bo rng không có ai bên d
i khi s dng
dng c trên cao.
5. Cm chc dng c bng c hai tay.
6. Gi tay tránh xa các b phn quay.
7. Không  mc dng c hot ng. Ch vn hành
dng c khi cm trên tay.
8. Không chm vào mi khoan hay vt gia công ngay
sau khi vn hành; chúng có th rt nóng và có th
gây bng da.
9. Mt s vt liu có th cha hoá cht c. Hãy cn
th
n  tránh hít phi bi và tip xúc vi da. Tuân
theo d liu an toàn ca nhà cung cp vt liu.
13
LU GI CÁC HNG DN NÀY.
CNH BÁO:
KHÔNG c  s thoi mái hay quen thuc vi sn
phm (có c do s dng nhiu ln) thay th vic
tuân th nghiêm ngt các quy nh v an toàn dành
cho sn phm này. VIC DÙNG SAI hoc không tuân
theo các quy nh v an toàn c nêu trong tài liu
hng dn này có th dn n thng tích cá nhân
nghiêm trng.
LP RÁP
Lp t tay cm hông (tay cm ph tr)
(Hình 1)
CN TRNG:
•Luôn m bo rng dng c này ã c tt và rút
phích cm trc khi lp hoc tháo g tay cm hông.
Luôn s dng tay cm hông  m bo vn hành an
toàn. Lp t tay cm hông sao cho rng ca tay cm
khp vào gia phn nhô ra ca tang trng dng c. Sau ó
vn cht tay cm bng cách xoay theo chiu kim ng h
n v trí mong mun. Tay cm có th
xoay 360°  c
gi cht bt c v trí nào.
Lp hoc tháo u mi khoan (Hình 2)
CN TRNG:
•Luôn m bo rng dng c này ã c tt và rút
phích cm trc khi lp hoc tháo g mi khoan.
 lp t u mi, t nó vào trong ngàm kp ht mc
có th. Vn phn ngàm kp li bng tay. t khóa ngàm
vào mt trong ba l nh ri vn cht theo chiu kim ng
h. m bo vn cht c ba l ngàm 
u nhau.  tháo
mi khoan, hãy xoay khóa ngàm ngc chiu kim ng
h ch mt l, sau ó vn lng b phn ngàm bng tay.
Sau khi dùng khóa ngàm, phi m bo t nó v v trí
ban u.
Thanh o sâu (ph kin tùy chn) (Hình 3)
Thanh o sâu rt thun tin  khoan các l có chiu sâu
ng nht. Vn lng tay cm hông và lp thanh o sâu
vào l trong  tay cm. iu chnh thanh o sâu n 
sâu mong mun và vn cht tay cm hông.
LU Ý:
•Thanh o sâu không th dùng v trí ni thanh o sâu
vng vào hp s.
MÔ T CHC NNG
Hot ng công tc (Hình 4)
CN TRNG:
•Trc khi cm in vào dng c, luôn luôn kim tra
xem cn khi ng công tc có hot ng bình thng
hay không và tr v v trí “OFF” (TT) khi nh ra.
 khi ng dng c, ch cn kéo cn khi ng công
tc. Tc  dng c c gim xung bng cách tng lc
ép lên cn khi ng công tc. Nh c
n khi ng công
tc ra  dng.  tip tc vn hành, hãy kéo cn khi
ng công tc và sau ó nhn vào nút khóa.  dng
dng c t v trí ã khóa, hãy kéo cn khi ng công tc
ht mc, sau ó nh ra.
Hot ng công tc o chiu (Hình 5)
Dng c này có mt công tc o chiu  thay i chiu
xoay. Di chuyn cn gt công tc o chiu sang v trí
(mt A)  xoay theo chiu kim ng h hoc sang v trí
(mt B)  xoay ngc chiu kim ng h.
CN TRNG:
•Luôn luôn kim tra hng xoay trc khi vn hành.
•Ch s dng công tc o chiu sau khi dng c ã
d
ng hoàn toàn. Vic thay i hng xoay trc khi
dng c dng có th làm hng dng c.
Chn ch  hot ng (Hình 6)
Dng c này có mt cn chuyn ch  hot ng. 
khoan và óng búa, trt cn chuyn ch  hot ng
sang bên phi (biu tng ).  ch khoan, trt cn
chuyn ch  hot ng sang bên trái (biu tng ).
CN TRNG:
•Luôn trt cn chuyn ch  hot ng ht mc n
v tr ch
 bn mong mun. Nu bn vn hành dng
c này vi cn chuyn ch  hot ng c t
gia các biu tng , dng c có th b h hng.
VN HÀNH
Thao tác khoan búa
Khi khoan trong bê-tông, á granite, gch, v.v... trt cn
chuyn ch  hot ng sang v trí có biu tng 
dùng hot ng "khoan óng búa". m bo rng bn s
dng mi khoan có u bt tungsten-cacbua. Không c
n mnh khi l khoan bt u b nghn bi các mt vn
và các ht. Thay vào ó, hãy chy dng c ch  ch,
sau ó tháo riêng mi khoan kh
i l. Bng cách lp li
thao tác này vài ln, l khoan s c v sinh sch.
Sau khi khoan l, s dng bóng thi khí  v sinh bi
bn ra khi l.
Thao tác khoan
Khi khoan trong g, kim loi hoc vt liu nha, trt cn
chuyn ch  hot ng sang v trí có biu tng 
dùng thao tác "ch khoan".
Khoan vào g
Khi khoan vào g,  có kt qu tt nht cn s dng các
mi khoan dùng  khoan g và vít dn. Thanh vít dn
hng s giúp khoan d dàng hn bng cách a mi
khoan vào vt gia công.
Khoan vào kim loi
 phòng nga u mi b
trt ra lúc bt u khoan l,
hãy to mt vt lõm bng cách dùng dùi c tâm và óng
vào im cn khoan. t u mi khoan vào ch lõm này
và bt u khoan. S dng du nhn  ct khi khoan
kim loi. Tr các trng hp dùng st và ng thau cn
phi c khoan khô.
CN TRNG:
•Nhn dng c quá mc s không tng tc  khoan lên
c. Trên thc t
, vic nhn mnh thêm này s ch
làm gây hng u mi ca bn, gim hiu nng và tui
th hot ng ca dng c.
•S có lc quán tính rt ln trên dng c/mi khoan lúc
l khoan c xuyên thng. Gi cht dng c
chun b ghìm lc quán tính li khi mi khoan xuyên
thng vt gia công.
14
•Mi khoan b kt có th c tháo ra n gin bng
cách t công tc o chiu sang ch  xoay ngc
li  rút mi khoan ra. Tuy nhiên, dng c th quay
ngc ra bt ng nu bn không gi cht.
•Luôn luôn gi cht các vt gia công có kích thc nh
bng kìm hoc dng c kp tng t.
BO TRÌ
CN TRNG:
•Luôn luôn m bo rng dng c ã c tt và tháo
phích cm trc khi dùng dng c thc hin bt c
công vic nào.
•Không bao gi dùng xng, ét xng, dung môi, cn
hoc hóa cht tng t. Có th xy ra hin tng mt
màu, bin dng hoc nt v.
 duy trì s an toàn và tin cy ca sn phm, mi sa
cha, b
o trì hoc iu chnh dng c u phi c thc
hin bi Trung tâm Dch v y quyn ca Makita.
15





 

END201-5



.......
..................
ENE039-1

   
  
ENF002-2


  

GEA005-3


! 

 /


   () 
  ( ) 


1.  

2.  

  


3.
  



4.   
 

 

5.    
   
 
6. 
 

1. 
2.  ()
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. 
12. 

13. 
14. 
 M804 M814

 16 .13 .
 30 .18 .
 13 .13 .
 ()0 - 3,0000 - 2,800
Blows per minute 0 - 45,000 0 - 30,800
 297 .272 .
 2.0 .1.6 .
 /II
16
7.    
 
   

8.  
 

9. 
  
 (RCD)  RCD 

10.  RCD  
 30 mA 

11.   
 
 

   
 

12.   
      



13.  
 / 
  
 

14. 
 


15.  
 

16.  
  
  
   

17.   



18. 
 
 


19.   


20.  /

  
 

21.  
 

 

22.  

 
  
  
 

23. 



24.     
 
 


25. 

 

26.

27.   
GEB003-5


1.  

2.   

3. 



 

4. 
 
5. 
6. 
7.   

8. 


9.  
 


17

:
 (
) 
 



 () ( 1)
:
 

  
 
 
  360° 

 ( 2)
:
 

  
   
  

 
 
 () ( 3)
 
 
 

:


 ( 4)
:
 
  “OFF” 
 
  
 

  
 ( 5)
  

( A) 
 
( B) 
:

 


 ( 6)
 
 ( ) 
 
( )
:
 
 
 



    
 
  
  
  
 


   
 

  
 

 
 
  
  
 
:
 
 

/ 
 
 

  
  
18
 

:
 
 
    
   
 

 Makita  

19
Makita Corporation
Anjo, Aichi, Japan
884554-370 www.makita.com
TRD
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Makita M804 Používateľská príručka

Kategória
Elektrické náradie
Typ
Používateľská príručka
Táto príručka je tiež vhodná pre

V iných jazykoch