Zanussi ZDF21001XA Používateľská príručka

Značka: Zanussi

Model: ZDF21001XA

Kategória: Umývačky riadu

Typ: Používateľská príručka

Táto príručka je tiež vhodná pre

ZDF21001WA

GETTING

STARTED?

EASY.

User Manual

ZDF21001WA

ZDF21001XA

EN User Manual 2

Dishwasher

FR Notice d'utilisation 17

Lave-vaisselle

SK Návod na používanie 34

Umývačka

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible if an

incorrect installation and use causes injuries and damages.

Always keep the instructions with the appliance for future

reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

• Do not let children play with the appliance.

• Keep all detergents away from children.

• Keep children and pets away from the appliance door when it is

open.

• Cleaning and user maintenance shall not be made by children

without supervision.

GENERAL SAFETY

• This appliance is intended to be used in household and similar

applications such as:

– farm houses; staff kitchen areas in shops, offices and other

working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum) must be

between 0.5 (0.05) / 8 (0.8) bar (Mpa)

• Obey the maximum number of 13 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put knives and cutlery with sharp points in the cutlery basket

with the points down or in a horizontal position.

• Do not keep the appliance door open without supervision to

prevent to fall on it.

• Before maintenance, deactivate the appliance and disconnect

the mains plug from the mains socket.

• Do not use water spray and steam to clean the appliance.

• The ventilation openings in the base (if applicable) must not be

obstructed by a carpet.

• The appliance is to be connected to the water mains using the

new supplied hose-sets. Old hose sets must not be reused.

SAFETY INSTRUCTIONS

INSTALLATION

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Do not install or use the appliance where the

temperature is less than 0 °C.

• Obey the installation instruction supplied with

the appliance.

ELECTRICAL CONNECTION

WARNING! Risk of fire and electrical

shock.

• The appliance must be earthed.

• Make sure that the electrical information on the

rating plate agrees with the power supply. If not,

contact an electrician.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance complies with the E.E.C.

Directives.

• Only for UK and Ireland. The appliance has a 13

amp mains plug. If it is necessary to change the

fuse in the mains plug, use fuse: 13 amp ASTA

(BS 1362).

WATER CONNECTION

• Make sure not to cause damage to the water

hoses.

• Before you connect the appliance to new pipes

or pipes not used for a long time, let the water

flow until it is clean.

• The first time you use the appliance, make sure

that there is no leakage.

• If the water inlet hose is damaged, immediately

disconnect the mains plug from the mains

socket. Contact the Authorised Service Centre

to replace the water inlet hose.

USE

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous. Obey

the safety instructions on the detergent

packaging.

• Do not drink and play with the water in the

appliance.

• Do not remove the dishes from the appliance

until the programme is completed. There can be

detergent on the dishes.

• The appliance can release hot steam if you open

the door while a programme operates.

• Do not put flammable products or items that are

wet with flammable products in, near or on the

appliance.

DISPOSAL

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent children and

pets to get closed in the appliance.

EASY START

1 2 3

456

On/off indicator

Programme marker

Indicators

Start button

Delay button

Programme knob

INDICATORS

End indicator.

Salt indicator. It is always off while the programme operates.

Rinse aid indicator. It is always off while the programme operates.

PROGRAMMES

Programme

Degree of soil

Type of load

Programme phases

Consumption values

Duration

(min)

Energy

(kWh)

Water

(l)

Normal soil

Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinses

• Dry

195 1.039 11

Heavy soil

Crockery, cut-

lery, pots and

pans

• Prewash

• Wash 70 °C

• Rinses

• Dry

150 -

170

1.5 - 1.6 13 - 15

Normal soil

Crockery and

cutlery

• Prewash

• Wash 65 °C

• Rinses

• Dry

120 -

130

1.3 - 1.6 15 - 17

Fresh soil

Crockery and

cutlery

• Wash 60 °C

or 65 °C

• Rinses

30 0.8 9

All • Prewash 14 0.1 4

1) The pressure and the temperature of the water, the variations of the mains supply, the options and the

quantity of dishes can change the values.

2) With this programme you have the most efficient use of water and energy consumption for crockery and

cutlery with normal soil. (This is the standard programme for test institutes).

3) This programme has a high temperature rising phase for better hygiene results. During the rinsing

phase, the temperature stays at 70 °C for at least 10 minutes.

4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.

5) Use this programme to quickly rinse the dishes. this prevents the remaining food to bond on the dishes

and bad odours to come out from the appliance. Do not use detergent with this programme.

INFORMATION FOR TEST INSTITUTES

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC) that is on

the rating plate.

BEFORE FIRST USE

1. Make sure that the current level of the

water softener agrees with the hardness

of the water supply. If not, adjust the level

of the water softener. Contact your local

water authority to know the water

hardness in your area.

2. Fill the salt container with special salt for

dishwasher.

3. Fill the rinse aid dispenser with special rinse

aid for dishwasher.

4. Open the water tap.

5. Start a programme to remove any processing

residuals that can still be inside the appliance.

Do not use detergent and do not load the

baskets.

THE WATER HARDNESS TABLE

German degrees

(°dH)

French degrees

(°fH)

mmol/l Clarke degrees

Water softener

level

47 -50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1) Factory setting

2) Do not use salt at this level.

Adjusting the water softener

The programme marker must be aligned with .

• Make sure that the appliance is in programme selection mode.

• Press and hold and simultaneously turn the knob counterclockwise until the programme marker is

aligned with .

• Release when Delay and start to flash.

• Press . Indicators , Delay and flash. The current setting is indicated by the intermittent

flashing of the indicator : e.g. 5 intermittent flashes + pause + 5 intermittent flashes = level 5.

• Press to change the setting. Each time you press the button, the level increases. After level 10 you

will start again from level 1.

• Turn the knob to to confirm the setting.

ADDING SALT

Before first use put one litre of water in the salt container.

Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after

you fill the salt container, start a programme.

ADDING RINSE AID

The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot

rinse phase.

DAILY USE

1. Open the water tap.

2. Set the correct programme for the type of load

and the degree of soil.

Make sure that the appliance is in Programme

selection mode.

• If the salt indicator is on, fill the salt

container.

• If the rinse aid indicator is on, fill the rinse

aid dispenser.

3. Load the baskets.

4. Start the programme.

ADDING DETERGENT

If the programme has a prewash phase, put a small quantity of detergent also in compartment B.

ADDING MULTI-TABLETS

PROGRAMME SELECTION MODE

The appliance must be in Programme selection mode to start a programme. If the control panel does not

show this condition, do the Reset.

RESET

With Reset you can cancel the running programme or the delay start. The appliance goes back to the

Programme selection mode.

STARTING A PROGRAMME

Open the water tap, close the door, select a programme, press .

OPTION DELAY

With this option you can postpone the start of a programme of 3 hours.

Set the programme, press Delay.

Press to start the countdown.

At the end of the countdown, the programme starts.

OPENING THE DOOR WHILE THE APPLIANCE OPERATES

If you open the door while a programme is running, the appliance stops. When you close the door, the

appliance continues from the point of interruption.

AT THE END OF THE PROGRAMME

5 min

The indicator comes on. If you do not deactivate the appliance within 5 minutes all indicators goes off.

This helps to decrease energy consumption.

Turn the knob to . Close the tap.

HINTS AND TIPS

GENERAL

The following hints will ensure optimal cleaning and

drying results in daily use and also help to protect

the environment.

• Remove larger residues of food from the dishes

into the waste bin.

• Do not pre-rinse dishes by hand. When needed,

use the prewash programme (if available) or

select a programme with a prewash phase.

• Always use the whole space of the baskets.

• When loading the appliance, make sure that the

dishes can be completely reached and washed

by the water released from the spray arm

nozzles. Make sure that items do not touch or

cover each other.

• You can use dishwasher detergent, rinse aid

and salt separately or you can use the multi-

tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the

instructions written on the packaging.

• Select the programme according to the type of

load and degree of soil. With the ECO

programme you have the most efficient use of

water and energy consumption for crockery and

cutlery with normal soil.

THE WATER SOFTENER

The water softener removes minerals from the

water supply, which would have a detrimental effect

on the washing results and on the appliance.

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. It is important to set the right

level of the water softener to assure good washing

results.

USING SALT, RINSE AID AND DETERGENT

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause damage

to the appliance.

• Multi-tablets are usually suitable in areas with a

water hardness up to 21 °dH. In areas

exceeding this limit, rinse aid and salt must be

used in addition to the multi-tablets. However, in

areas with hard and very hard water we

recommend to use solo-detergent (powder, gel,

tablets without additional functions), rinse aid

and salt separately for optimal cleaning and

drying results.

• Detergent tablets do not fully dissolve with short

programmes. To prevent detergent residues on

the tableware, we recommend that you use the

tablets with long programmes.

• Do not use more than the correct quantity of

detergent. Refer to the instructions on the

detergent packaging.

WHAT TO DO IF YOU WANT TO STOP USING

MULTI-TABLETS

Before you start to use separately detergent, salt

and rinse aid do the following procedure.

1. Set the highest level of the water softener.

2. Make sure that the salt and rinse aid containers

are full.

3. Start the shortest programme with a rinsing

phase. Do not add detergent and do not load

the baskets.

4. When the programme is completed, adjust the

water softener according to the water hardness

in your area.

5. Adjust the released quantity of rinse aid.

6. Activate the rinse aid dispenser.

LOADING THE BASKETS

• Only use the appliance to wash items that are

dishwasher-safe.

• Do not put in the appliance items made of

wood, horn, aluminium, pewter and copper.

• Do not put in the appliance items that can

absorb water (sponges, household cloths).

• Remove remaining food from the items.

• Make soft the remaining burned food on the

items.

• Put hollow items (cups, glasses and pans) with

the opening down.

• Make sure that cutlery and dishes do not bond

together. Mix spoons with other cutlery.

• Make sure that glasses do not touch other

glasses.

• Put small items in the cutlery basket.

• Put light items in the upper basket. Make sure

that the items do not move.

• Make sure that the spray arm can move freely

before you start a programme.

BEFORE STARTING A PROGRAMME

Make sure that:

• The filters are clean and correctly installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is dishwasher salt and rinse aid (unless

you use multi- tablets).

• The position of the items in the baskets is

correct.

• The programme is applicable for the type of load

and for the degree of soil.

• The correct quantity of detergent is used.

UNLOADING THE BASKETS

1. Let the tableware cool down before you

remove it from the appliance. Hot items can be

easily damaged.

2. First remove items from the lower basket, then

from the upper basket.

At the end of the programme water

can still remain on the sides and on

the door of the appliance.

CARE AND CLEANING

WARNING! Before maintenance,

deactivate the appliance and

disconnect the mains plug from the

main socket.

Dirty filters and clogged spray arms

decrease the washing results. Make a

check regularly and, if necessary,

clean them.

CLEANING THE FILTERS

• Make sure that there are no residues of food or soil in or around the edge of the sump.

• Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides.

• Reassemble the filters (A) and (B).

• Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks.

An incorrect position of the filters can cause bad washing results and damage to the

appliance

CLEANING THE SPRAY ARMS

Do not remove the spray arms. If the holes in the

spray arms are clogged, remove remaining parts of

soil with a thin pointed object.

EXTERNAL CLEANING

• Clean the appliance with a moist soft cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning

pads or solvents.

INTERNAL CLEANING

• Carefully clean the appliance, including the

rubber gasket of the door, with a soft damp

cloth.

• If you regularly use short duration programmes,

these can leave deposits of grease and

limescale inside the appliance. To prevent this,

we recommend to run long duration

programmes at least 2 times per month.

• To maintain the performance of your appliance

at its best, we recommend to use monthly a

specific cleaning product for dishwashers.

Follow carefully the instructions on the

packaging of the product.

TROUBLESHOOTING

If the appliance does not start or it stops during

operation, before you contact an Authorised

Service Centre, check if you can solve the problem

by yourself with the help of the information in the

table.

WARNING! Repairs not properly done

may result in serious risk to the safety

of the user. Any repairs must be

performed by qualified personnel.

With some problems the end indicator flashes

intermittently indicating a malfunction.

The majority of problems that can occur can

be solved without the need to contact an

Authorised Service Centre.

Problem and alarm code Possible cause and solution

You cannot activate the appliance. • Make sure that the mains plug is connected to the

mains socket.

• Make sure that there is no damaged fuse in the fuse

box.

The programme does not start. • Make sure that the appliance door is closed.

• If the delay start is set, cancel the setting or wait for

the end of the countdown.

• The appliance has started the procedure to re-

charge the resin inside the water softener. The dura-

tion of the procedure is approximately 5 minutes.

The appliance does not fill with water.

• The end indicator flashes 1 time inter-

mittently.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is

not too low. For this information, contact your local

water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not clog-

ged.

• Make sure that the inlet hose has no kinks or bends.

The appliance does not drain the water.

• The end indicator flashes 2 times inter-

mittently.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or

bends.

The anti-flood device is on.

• The end indicator flashes 3 times inter-

mittently.

• Close the water tap and contact an Authorised

Service Centre.

The appliance stops and starts more

times during operation.

• It is normal. It provides optimal cleaning results and

energy savings.

The program lasts too long. • If the delayed start option is set, cancel the delay

setting or wait for the end of the countdown.

Small leak from the appliance door. • The appliance is not level. Loosen or tighten the ad-

justable feet (if applicable).

• The appliance door is not centred on the tub. Adjust

the rear foot (if applicable).

The appliance door is difficult to close. • The appliance is not level. Loosen or tighten the ad-

justable feet (if applicable).

• Parts of the tableware are protruding from the bas-

kets.

Rattling/knocking sounds from inside the

appliance.

• The tableware is not properly arranged in the bas-

kets. Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

Problem and alarm code Possible cause and solution

The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneous-

ly all the appliances in use. Check the socket am-

perage and the capacity of the meter or turn off one

of the appliances in use.

• Internal electrical fault of the appliance. Contact an

Authorised Service Centre.

Refer to "Before first use", "Daily

use", or "Hints and tips" for other

possible causes.

For alarm codes not described in the table, contact

an Authorised Service Centre.

THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY

Problem Possible cause and solution

Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading

leaflet.

• Use more intensive washing programmes.

Poor drying results. • Tableware has been left for too long inside a closed appli-

ance.

• There is no rinse aid or the dosage of rinse aid is not enough.

Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• We recommend to always use rinse aid, even in combination

with multi-tablets.

There are whitish streaks or blu-

ish layers on glasses and dishes.

• The release quantity of rinse aid is too much. Adjust the rinse

aid level to a lower level.

• The quantity of detergent is too much.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust the

rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The dishes are wet. • The programme does not have a drying phase or has a drying

phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a differ-

ent brand or activate the rinse aid dispenser and use rinse

aid and multi-tablets together.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the hu-

midity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent for dishwashers only.

• There is a leak in the rinse aid dispenser. Contact an Author-

ised Service Centre.

Problem Possible cause and solution

Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to

"The water softener".

• Silver and stainless steel cutlery were placed together. Avoid

to put silver and stainless steel items close together.

There are residues of detergent

in the dispenser at the end of the

programme.

• The detergent tablet got stuck in the dispenser and therefore

was not completely washed away by water.

• Water cannot wash away the detergent from the dispenser.

Make sure that the spray arm is not blocked or clogged.

• Make sure that items in the baskets do not impede the lid of

the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the table-

ware, on the tub and on the in-

side of the door.

• Refer to "The water softener".

Dull, discoloured or chipped ta-

bleware.

• Make sure that only dishwasher-safe items are washed in the

appliance.

• Load and unload the basket carefully. Refer to basket loading

leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use", "Daily

use" or "Hints and tips" for other

possible causes.

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 600 / 850 / 625

Electrical connection

1) Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

2) max 60 °C

Capacity Place settings 13

Power consumption Left-on mode (W) 5.0

Power consumption Off-mode (W) 0.50

1) Refer to the rating plate for other values.

2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot

water supply to decrease energy consumption.

RATING PLATE

Mod. ... ... ...

Prod. No. ... ... ...

Ser. No. ...

INFORMATION FOR TEST INSTITUTES

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC) that is on

the rating plate.

ENVIRONMENT CONCERNS

Recycle the materials with the symbol . Put the

packaging in applicable containers to recycle it.

Help protect the environment and human health

and to recycle waste of electrical and electronic

appliances. Do not dispose appliances marked with

the symbol with the household waste. Return the

product to your local recycling facility or contact

your municipal office.

CONSIGNES DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez soigneusement les

instructions fournies. Le fabricant ne peut être tenu pour

responsable des dommages et blessures liés à une mauvaise

installation ou utilisation. Conservez toujours cette notice avec

votre appareil pour vous y référer ultérieurement.

SÉCURITÉ DES ENFANTS ET DES PERSONNES

VULNÉRABLES

• Cet appareil peut être utilisé par des enfants âgés d'au moins 8

ans et par des personnes ayant des capacités physiques,

sensorielles ou mentales réduites ou dénuées d’expérience ou

de connaissance, s’ils (si elles) sont correctement surveillé(e)s

ou si des instructions relatives à l’utilisation de l'appareil en

toute sécurité leur ont été données et si les risques encourus

ont été appréhendées.

• Les enfants ne doivent pas jouer avec l’appareil.

• Ne laissez pas les détergents à la portée des enfants.

• Tenez les enfants et les animaux éloignés de la porte de

l'appareil lorsque celle-ci est ouverte.

• Le nettoyage et l’entretien par l'usager ne doivent pas être

effectués par des enfants sans surveillance.

CONSIGNES GÉNÉRALES DE SÉCURITÉ

• Cet appareil est conçu uniquement pour un usage domestique

et des utilisations telles que :

– bâtiments de ferme, cuisines réservées aux employés dans

les magasins, bureaux et autres lieux de travail ;

– pour une utilisation privée, par les clients, dans des hôtels et

autres lieux de séjour.

• Ne modifiez pas les caractéristiques de cet appareil.

• La pression de l'eau en fonctionnement (minimale et maximale)

doit se situer entre 0.5 (0.05) / 8 (0.8) bar (Mpa)

• Respectez le nombre maximum de 13 couverts.

• Si le câble d'alimentation est endommagé, il doit être remplacé

par le fabricant, son service après-vente ou des personnes de

qualification similaire afin d'éviter un danger.

• Placez les couteaux et les couverts avec des bouts pointus

dans le panier à couverts avec les pointes tournées vers le bas

ou en position horizontale.

• Ne laissez pas la porte de l'appareil ouverte sans surveillance

pour éviter tout risque de chute.

• Avant toute opération d'entretien, éteignez l'appareil et

débranchez la fiche de la prise secteur.

• Ne pulvérisez pas d'eau ni de vapeur pour nettoyer l'appareil.

• Les orifices d'aération situés à la base (si présents) ne doivent

pas être obstrués par de la moquette.

• L'appareil doit être raccordé au réseau de distribution d'eau en

utilisant les ensembles de raccordement neufs fournis avec

l'appareil, il convient de ne pas réutiliser des ensembles de

raccordement usagés.

INSTRUCTIONS DE SÉCURITÉ

INSTALLATION

• Retirez l'intégralité de l'emballage.

• N'installez pas et ne branchez pas un appareil

endommagé.

• N'installez pas l'appareil ou ne l'utilisez pas dans

un endroit où la température ambiante est

inférieure à 0 °C.

• Suivez scrupuleusement les instructions

d'installation fournies avec l'appareil.

CONNEXION ÉLECTRIQUE

AVERTISSEMENT! Risque

d'incendie ou d'électrocution.

• L'appareil doit être relié à la terre.

• Vérifiez que les données électriques figurant sur

la plaque signalétique correspondent à celles

de votre réseau. Si ce n'est pas le cas,

contactez un électricien.

• Utilisez toujours une prise de courant de

sécurité correctement installée.

• N'utilisez pas d'adaptateurs multiprises ni de

rallonges.

• Veillez à ne pas endommager la fiche secteur ni

le câble d'alimentation. Le remplacement du

cordon d'alimentation de l'appareil doit être

effectué par notre service après-vente.

• Ne connectez la fiche d'alimentation secteur à la

prise de courant secteur qu'à la fin de

l'installation. Assurez-vous que la fiche

d'alimentation est accessible une fois l'appareil

installé.

• Ne tirez jamais sur le câble d'alimentation

électrique pour débrancher l'appareil. Tirez

toujours sur la fiche.

• Cet appareil est conforme aux directives CEE.

• Uniquement pour le R-U et l'Irlande. L'appareil

dispose d'une alimentation secteur de 13 A. S'il

est nécessaire de changer le fusible de la fiche

électrique, utilisez le fusible : 13 amp ASTA (BS

1362).

RACCORDEMENT À L'ARRIVÉE D'EAU

• Veillez à ne pas endommager les tuyaux de

circulation d'eau.

• Avant de brancher l'appareil à des tuyaux neufs

ou n'ayant pas servi depuis longtemps, laissez

couler l'eau jusqu'à ce qu'elle soit propre.

• Avant d'utiliser l'appareil pour la première fois,

assurez-vous de l'absence de fuites.

• Si le tuyau d'arrivée d'eau est endommagé,

débranchez immédiatement la fiche de la prise

secteur. Contactez le service après-vente pour

remplacer le tuyau d'arrivée d'eau.

UTILISATION

• Ne montez pas sur la porte ouverte de votre

appareil ; ne vous asseyez pas dessus.

• Les produits de lavage pour lave-vaisselle sont

dangereux. Suivez les consignes de sécurité

figurant sur l'emballage du produit de lavage.

• Ne buvez pas l'eau de l'appareil ; ne jouez pas

avec.

• N'enlevez pas la vaisselle de l'appareil avant la

fin du programme. Il peut rester du produit de

lavage sur la vaisselle.

• De la vapeur chaude peut s'échapper de

l'appareil si vous ouvrez la porte pendant le

déroulement d'un programme.

• Ne placez pas de produits inflammables ou

d'éléments imbibés de produits inflammables à

l'intérieur ou à proximité de l'appareil, ni sur

celui-ci.

MISE AU REBUT

AVERTISSEMENT! Risque de

blessure ou d'asphyxie.

• Débranchez l'appareil de l'alimentation

électrique.

• Coupez le câble d'alimentation et mettez-le au

rebut.

• Retirez le dispositif de verrouillage de la porte

pour empêcher les enfants et les animaux de

s'enfermer dans l'appareil.

DÉMARRAGE FACILE

1 2 3

456

Voyant Marche/Arrêt

Indicateur de programme

Voyants

Touche Départ

Touche Départ différé

Sélecteur de programme

VOYANTS

Voyant de fin.

Voyant du réservoir à sel régénérant. Ce voyant est toujours éteint pendant le déroule-

ment du programme.

Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le dé-

roulement du programme.

Stránka sa načítava ...

Zanussi ZDF21001XA Používateľská príručka

Značka: Zanussi

Model: ZDF21001XA

Kategória: Umývačky riadu

Typ: Používateľská príručka

Táto príručka je tiež vhodná pre

ZDF21001WA

Stiahnite si PDF

správa

V iných jazykoch

français: Zanussi ZDF21001XA Manuel utilisateur
English: Zanussi ZDF21001XA User manual

Zanussi ZDF21001XA Používateľská príručka

Táto príručka je tiež vhodná pre

Zanussi ZDF21001XA Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty