Fieldmann FZD 5015 E Používateľská príručka

FZD 5015 E

EN 2

FZD 5015 E

English .................................................................................................................................................................................3–18

Čeština ............................................................................................................................................................................. 19–34

Slovenčina .....................................................................................................................................................................35–50

Magyarul ........................................................................................................................................................................ 51–66

Polski ................................................................................................................................................................................. 67–82

EN

GARDEN SHREDDER USER'S MANUAL

3

Contents

Garden Shredder

USER’S MANUAL

Dear customer,

thank you very much for the trust that you have expressed!

Before putting this machine into operation, it is imperative to read this user’s manual! In it,

you will ﬁ nd all the instructions for normal operation and for achieving a long lifetime of the

machine. It is imperative to adhere to all safety instructions contained in this user’s manual.

CONTENTS

1. GENERAL SAFETY INSTRUCTIONS ........................................................................................................................4

Important safety notice ............................................................................................................................................4

Instructions for use .......................................................................................................................................................4

2. SYMBOLS ...........................................................................................................................................................................5

3. BEFORE YOU BEGIN… ................................................................................................................................................. 6

Operation within the scope of intended use ...............................................................................................6

4. FOR YOUR SAFETY ........................................................................................................................................................6

General safety instructions .....................................................................................................................................6

Electrical safety .............................................................................................................................................................7

Maintenance .................................................................................................................................................................7

Notiﬁ cations speciﬁ c to this machine ...............................................................................................................7

5. DESCRIPTION OF THE MACHINE ..........................................................................................................................9

Description of the machine (see Fig. 1) ..........................................................................................................9

6. ASSEMBLING THE SHREDDER ...............................................................................................................................10

7. OPERATING THE SHREDDER..................................................................................................................................12

Turning the shredder on and off (Fig. 5) ........................................................................................................12

Forward / reverse rotation switch (Fig. 5, point 3) .....................................................................................12

Protection against overload ................................................................................................................................13

Collection box ..............................................................................................................................................................13

Cutting roller cover (Fig. 1, point 11) .................................................................................................................13

8. SETTING UP AND WORKING WITH THE SHREDDER ...................................................................................14

Setting the counter-blade distance .................................................................................................................14

Before turning on ........................................................................................................................................................14

Material that the shredder can process ........................................................................................................14

The shredder MUST NOT process the following types of materials: ................................................14

9. OPERATION ...................................................................................................................................................................15

10. MAINTENANCE ............................................................................................................................................................15

11. TROUBLESHOOTING ..................................................................................................................................................16

12. TECHNICAL SPECIFICATIONS ...............................................................................................................................17

13. DISPOSAL ........................................................................................................................................................................17

14. DECLARATION OF CONFORMITY ......................................................................................................................18

EN 4

FZD 5015 E

General safety instructions

1. GENERAL SAFETY INSTRUCTIONS

Important safety notice

Carefully unpack the product and take care not to throw away any part of the packaging before you ﬁ nd all

the parts of the product.

Store the product in a dry place out of reach of children.

Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical

shock, a ﬁ re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so

can be handed over for recycling.

Instructions for use

Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself

with the operating elements and the correct use of the machine. Keep the user’s manual in a safe place where

it can be easily retrieved for future use. Save the original packaging, including the internal packing material,

warranty card and proof of purchase receipt at least for the duration of the warranty. If you need to ship this

machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport (e.g.

when moving or when sending it for repair to a service centre).

NOTE: If you hand over the machine to somebody else, do so together with this user’s manual. Following

the instructions in the included user’s manual is a prerequisite for the proper use of the machine. The

user’s manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not

following the instructions in this manual.

EN

GARDEN SHREDDER USER'S MANUAL

5

Symbols

2. SYMBOLS

Follow the safety instructions prior to putting into operation.

Prior to putting into operation, read the user's manual and adhere to it.

Danger of amputation.

Do not reach into the funnel.

Risk from deﬂ ected objects.

Maintain a safe distance from bystanders.

If the cable is damaged or interrupted, immediately disconnect the plug from the

mains.

94 dB Machine noise level.

ATTENTION: Do not use the shredder in humid or rainy weather

and protect it against moisture.

Wait for all parts of the shredder to come to a stop.

Personal protective work aids

Use hearing protection and wear safety glasses when working with the machine.

Use solid footwear when working with the machine.

Use safety gloves when working with the machine.

Use close-ﬁ tting work clothes when working with the machine.

EN 6

FZD 5015 E

Before you begin... | For you safety

3. BEFORE YOU BEGIN…

Operation within the scope of intended use

it complies with the state of science and technology and safety provisions in force at the time that it is put

into operation within the scope of its intended use. The machine is intended for shredding ﬁ brous and woody

organic household and garden material. It cannot be ﬁ lled with rocks, glass, metals, bones, plastic or textile

waste materials.

it is not designed for professional use. Any other use is in contradiction with the designated purpose.

Operation in contradiction with the determined intended use, modiﬁ cations made to the machine or the use

of parts that were not pre-tested and approved by the manufacturer, may result in unforeseeable damage!

All inappropriate use or any activities not described in this user’s manual performed with the machine

are considered to constitute prohibited misuse that is beyond the legal boundaries for the warranty of the

manufacturer.

4. FOR YOUR SAFETY

General safety instructions

For the safe operation of this machine, its users must read this user’s manual and understand it before ﬁ rst

use.

Respect all safety instructions! If you do not adhere to the safety instructions, you are endangering yourself

and others.

Carefully store all user’s manuals and safety instructions for future reference.

If you sell or hand the machine over to somebody, unconditionally also hand over this user’s manual.

The machine must only be used when it is free of defects. If the machine or its part is damaged, it must be

repaired by a professional.

Do not use the machine in places where there is a risk of explosion or in the vicinity of ﬂ ammable ﬂ uids or

gasses!

Always secure a turned off machine against it being turned on accidentally.

Do not use a machine on which its On/Off switch does not work.

Prevent children access to the machine! Store the machine so that it is secured against children and

unauthorised persons.

Do not overload the machine. Only use the machine for the purposes for which it was designed.

Always use the required protective safety equipment.

Always work very carefully and be in good physical condition: Working when tired or ill, after consuming

alcohol, under the inﬂ uence of medication or narcotics is dangerous because you cannot operate the

machine safely.

Do not use a heating element with a timer switch or another type of switch that automatically switches on

the machine, this would represent a ﬁ re hazard.

Take steps to ensure that children do not play with the product.

Always adhere to valid national and international safety, health and work regulations.

EN

GARDEN SHREDDER USER'S MANUAL

7

For you safety

Electrical safety

The machine may only be connected to a power socket with a properly installed protective contact.

The machine must be protected by a residual current device (FI switch) with a rated false current not

exceeding 30 mA.

Prior to connecting the machine it is necessary to ensure that the mains connection corresponds to the

values for the connection of the machine.

The machine may only be used within the indicated current, power and speed limits (see rating label).

Do not touch the power plug with wet hands! Always pull the plug holding the connector, not the cable.

Do not bend, crimp, clamp, pull or drive over the power cord; protect it against sharp edges, oil and heat.

Do not lift the machine by the power cord and do not use the power cord for any other purposes.

Prior to every use, inspect the plug and power cord.

In the event that the power cord is damaged, immediately unplug the plug. Do not use a machine with

a damaged power cord.

If the machine is not being used, the power plug must always be unplugged.

Ensure that the machine is turned off before plugging in the power plug.

Always turn off the machine before unplugging the power plug.

Make sure there is not current in the machine before transporting it.

Maintenance

Pull the power plug out of the power socket before performing any type of work on the machine.

Only the maintenance and troubleshooting described in this user’s manual may be performed. All other work

must be performed by a professional.

Use only original spare parts. Only these spare parts are designed for the machine and appropriate.

Other spare parts will not only result in the warranty becoming void but may also endanger you and your

surroundings.

Notiﬁ cations speciﬁ c to this machine

Do not reach into the ﬁ lling funnel or the ejection chute while it is running. The machine continues to run

down for approx. 5 seconds after it is turned off.

The machine must be assembled according to the instructions before it is turned on.

Check that all screws, bolts, nuts and other fastening components are ﬁ rmly tightened and that protective

elements are properly installed before turning it on.

When working with the machine, make sure to maintain a stable and natural stance.

Work only under good light and visibility conditions.

The operator’s clothing must be tight-ﬁ tting. Loose clothing must be eliminated. Wear solid footwear and long

work pants.

Only use the machine outdoors on a ﬁ rm even surface.

Leave sufﬁ cient free space around the machine when using it. Do not stand the machine close to a wall.

Do not lift, tilt or transport the machine when it is running.

Before starting the machine, check that the insertion funnel is empty.

Never leave a running machine without supervision.

Make sure that no foreign objects enter the machine when it is running, e.g. rocks, glass, metal, soil, plastic,

etc. The could damage the motor and the cutting roller.

If foreign objects enter the cutting mechanism or the machine makes unusual noises or vibrates unusually,

immediately stop the motor and allow the machine to come to a complete stop.

EN 8

FZD 5015 E

For you safety

Never use the machine without the inserting funnel.

If the shredder becomes clogged, ﬁ rst turn the machine off and pull the plug out of the socket and wait for the

machine to come to a complete stop before removing the clogged material. Keep the On/Off switch clean

and free of foreign objects.

Never attempt to hold or remove shredded material while the cutting roller is in motion. Remove clogged

shredded material only when the machine is turned off.

Prevent direct contact with the rotating cutting roller. Keep hands and feet away from the openings when the

machine is running.

Do not insert your hands or other body parts or clothing into the ﬁ lling chamber, ejection chute or in the

vicinity of other moving parts.

Always remove shredded material from the ejection zone before it accumulates. This will prevent the

shredder from clogging and prevent the shredded material from entering the ﬁ lling funnel by recoil and

causing injuries.

No other persons or animals may stand within the radius of 3 m around the work area as they could be

injured by deﬂ ected objects.

Do not use the machine on a tiled or concrete ﬂ oor. The shredded material could deﬂ ect and cause injury.

The symbols found on your machine must not be removed or covered over. Notiﬁ cations on the machine that

are no longer legible must be replaced with new ones without delay.

EN

GARDEN SHREDDER USER'S MANUAL

9

Description of the machine

5. DESCRIPTION OF THE MACHINE

3

2

1

7

6

4

5

Fig. 1

Description of the machine (see Fig. 1)

1. Filling funnel

2. Control panel

3. Power cord

4. Collection box safety lock

5. Collection box

6. Cutting adjustment screw

7. Plastic pusher

EN 10

FZD 5015 E

Assembling the shredder

6. ASSEMBLING THE SHREDDER

ATTENTION: Prior to performing any work on the machine, check that it is turned off and disconnected

from the power supply.

1. Turn the shredder unit upside down and place it

on an even ﬂ oor.

Then lift the legs upwards. Fig 2.

2. Install the wheels as follows:

— Push the wheel axle through the holes in the

frame.

— put a washer and a wheel bushing on each

side of the axle. Fig 3.

— Put on the wheel and secure in place using

a nut. Fig 4.

— Insert a hex key through the opening in the

wheel’s axle and tighten the wheel nut. Fig 5.

— Finally put on the wheel cover.

— Repeat this procedure for both wheels.

3. Insert the collection box and lock in place using

the safety mechanism. Fig. 6, point 1

ATTENTION! The safety mechanism must be

properly locked, otherwise the machine will not

start.

Fig. 2

Fig. 3

Fig. 3.1

EN

GARDEN SHREDDER USER'S MANUAL

11

Fig. 4

Fig. 5

Fig. 6

Assembling the shredder

EN 12

FZD 5015 E

Operating the shredder

7. OPERATING THE SHREDDER

WARNING: Before connecting the machine to a power source, always check that the switch is turned off.

Connecting the machine with the switch in the on position may cause it to turn on unexpectedly and result in

a serious injury.

Turning the shredder on and off (Fig. 7)

ATTENTION: If it is not possible to turn the

switch on the machine on and off, do not work

with the machine. Have faulty switches replaced

at an authorised service centre.

To turn on the shredder, press the button with the

“I” symbol. Fig. 7., point 2

To turn off the shredder, press the button with the

“0” symbol. Fig. 7., point 1

ATTENTION: In the event of a power outage,

the machine will turn off automatically. To turn

on the shredder again, press the button with the

“I” symbol.

Forward / reverse rotation switch (Fig. 7, point 3)

ATTENTION: Turn the shredder off before switching the forward / reverse rotation.

Forward position

Standard operation of the shredder. The cutting roller rotates forwards.

Reverse position

The cutting roller rotates in the opposite direction for the purpose of releasing jammed material.

To change to the reverse rotation direction it is necessary to intermittently press the button with the “I” symbol

so that the roller rotates. The roller will stop automatically when the button is released.

NOTE: To shred large branches it may be necessary to repeat the forward and reverse procedure several

times. Prior to changing the rotation direction again, always wait until the shredder comes to a complete

stop.

Fig. 7

EN

GARDEN SHREDDER USER'S MANUAL

13

Operating the shredder

Protection against overload

The shredder is equipped with overload protection (Fig.7, point 4)

In the event of an overload, the motor protection will automatically disconnect the electrical circuit.

To renew functionality, proceed as follows:

1. Turn off the machine so that it is without voltage.

2. Remove the material that clogged the shredder.

3. Allow the motor to cool down for at least ﬁ ve minutes!

4. Press the safety fuse button (Fig. 7, point 4).

5. Reconnect the electrical power supply.

6. Turn on the shredder.

ATTENTION: To prevent accidents, to remove jammed objects, always use a hook or a stick.

Collection box

Always turn the shredder off and disconnect it from the power supply before attaching or removing the

collection box.

For safety reasons, the handle of the collection box (Fig. 6, point 1) is equipped with a safety lock.

For safe operation, check the working order of the safety lock after every two hours of work.

Never attempt to put the safety lock of the handle out of operation.

Handle of the collection box:

Handle in the lowered position >>> the collection box is not locked. The safety lock is activated,

the shredder cannot be started.

Handle in the raised position >>> the collection box is locked and the shredder is ready for work.

NOTE: The machine will not start if the collection box is unlocked. The machine will automatically turn off

when the collection box is released during operation.

EN 14

FZD 5015 E

Setting up and working with the shredder

8. SETTING UP AND WORKING

WITH THE SHREDDER

Setting the counter-blade distance

For effective operation, it is necessary to set the

distance between the counter-blade (Fig. 8, point

2) and the cutting roller (Fig. 8, point 3). The gap

between the cutting roller and the counter-blade

should be as small as possible.

A correct setting will enable the effective shredding

of all branch diameters.

Setting the distance:

Turn on the machine.

To pull the counter-blade towards the cutting

roller, slowly turn the setting screw (Fig. 8, point 1)

clockwise. Keep turning the screw until ﬁ ne aluminium ﬁ llings start falling out of the ejection chute.

NOTE: Soft material or wet branches may be torn instead of being cut. This problem may also be caused by

the counter-blade, which wears out after frequent use.

Before turning on

Make sure that:

Power cords are not damaged. If there are slits or cracks on a power cord, stop work and replace it

immediately.

The machine is not damaged and all the screws are pulled tight.

The machine is completely and correctly assembled.

Check the power supply:

Make sure that the supply voltage corresponds to the rated voltage on the rating label and that the machine

is properly grounded.

Only use extension cords that have wires with a sufﬁ cient cross-section.

Material that the shredder can process

The shredder can process the following types of materials:

All types of branches up to the maximum diameter speciﬁ ed in the technical speciﬁ cations.

Garden waste such as wilted plants or wet grass (shred alternatively with branches).

The shredder MUST NOT process the following types of materials:

Glass, metals, plastics, rocks, ceramics, branches thicker than speciﬁ ed in the technical speciﬁ cations, hard

wood, thick wooden boards, fabrics, plastic bags, roots with soil.

Wastes that are almost in liquid form, e.g. kitchen scraps.

Fig. 8

1

2

3

EN

GARDEN SHREDDER USER'S MANUAL

15

9. OPERATION

Place the material into the funnel from the right side.

Shred branches immediately after they are cut. When they dry out, they may become very hard.

Remove all lateral shoots from the branches if it is not possible to insert them into the shredder.

Avoid too much shredded material from accumulating in the collection box. Regularly empty the box

because accumulated shredded material may block the ejection chute.

Do not insert material that is larger than the maximum branch diameter speciﬁ ed in the technical

speciﬁ cations.

Shredding wet garden waste (fallen leaves) will result in clogging. To prevent clogging, alternate the waste

with material containing wood.

Soft materials or wet branches may be torn instead of being cut. This problem may also be caused by

a worn out counter-blade.

Before cleaning out the ejection chute, turn off the motor and disconnect the machine from the power supply.

10. MAINTENANCE

ATTENTION:

Prior to inspecting or performing maintenance on the machine, check that it is turned off and disconnected

from the power supply. Be careful, the cutting roller will not stop immediately after the machine is turned off,

wait for all the parts to stop moving.

Put on protective gloves before inspection or carrying out maintenance.

Never use petrol, thinners, alcohol, etc. for cleaning. This could result in discolouration, deformation

or cracking.

Only use a damp cloth and soft brush for cleaning the machine.

Do not use a hose or wash the machine with pressurised water.

After every work session, carry out the following maintenance:

Check that all fastening screws and bolts are tightened (tighten them if necessary).

Lubricate metal components to protect against corrosion.

Maintain holes clean and free of dust.

The cutting roller and counter-blade wear out over time. If necessary, inform yourself about replacement

at you nearest authorised service centre.

Operation | Maintenance

EN 16

FZD 5015 E

11. TROUBLESHOOTING

WARNING: Prior to troubleshooting, turn the machine off, disconnect it from the power supply and wait for

it to come to a complete stop.

Problem Possible cause Remedy

The motor will not start

No power supply Check the power supply.

Faulty power cord To check, inform yourself at an authorised

service centre

Fuse against overloading was activated Wait until the machine cools down and

press the fuse button.

The collection box safety lock (the

collection box is unlocked) Check and lock the collection box

The motor can be heard, but is

not working

The cutting roller is blocked

Turn off the machine.

Switch the forward/reverse switch to

reverse rotation.

Turn the machine on until the blockage is

cleared.

Again turn the machine off.

Switch back to the forward rotation.

Malfunction of a capacitor Take the machine to an authorised service

centre for repair.

The shredded material is not

being pulled into the shredder

The reverse rotation direction is set. Turn the machine off and switch the

rotation direction using the switch.

The shredded material is jammed in the

ﬁ lling funnel

Turn the machine off. Switch the forward/

reverse switch to reverse rotation. Turn

on the machine to release the shredded

material, remove undesired material.

Turn the machine off again.

Switch back to the forward rotation.

The shredded material is too soft or wet Push the material into the shredder

Incorrectly set counter-blade / cutting roller

Set the counter-blade as described in

"Setting up and working with the shredder".

In the event that the cutting roller / counter-

blade is heavily worn out, replace it.

The shredded material is not

cleanly chopped up The counter-blade is not set properly Set the counter-blade as described in the

previous paragraph

The machine turns on but is

blocked even by a small load

and is soon shut off by the motor

protection switch.

The extension cord is too long or the cross-

section of its wires is too small.

The power socket is too far from the power

source or the cross-section of the wires in

the power cord is too small

Check that the wire cross-section of the

extension cord is at least 1.5 mm2, and no

longer than 25 m. If a longer power cord is

used then the minimum wire cross-section

is 2.5 mm2

Troubleshooting

EN

GARDEN SHREDDER USER'S MANUAL

17

Technical Specifications | Disposal

12. TECHNICAL SPECIFICATIONS

Rated voltage .........................................................................................................................................................230–240 V~/50 Hz

Rated power input ....................................................................................................................................................................... 2800 W

Protection class ............................................................................................................................................................................................II

Protection marking ...............................................................................................................................................................................IP24

Idle speed .........................................................................................................................................................................................60 RPM

Maximum branch diameter .........................................................................................................................................................44 mm

Collection box capacity........................................................................................................................................................................60 l

Sound pressure level (LPA)* ................................................................................................................................................... 73 dB(A)

Sound power level (LWA)* ....................................................................................................................................................... 94 dB(A)

Weight .................................................................................................................................................................................................19.4 kg

13. DISPOSAL

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING

MATERIALS

Dispose of used packaging material at a site designated for waste in your municipality.

The machine and its accessories are manufactured from various materials, e.g. metal and

plastic.

Take damaged parts to a recycling centre. Inquire at the relevant government department.

This appliance meets all the basic requirements of EU directives related to it.

Changes in the text, design and technical speciﬁ cations may be made without prior notice and we reserve

the right to make these changes.

User’s manual in the original language.

EN 18

FZD 5015 E

Declaration Of Conformity

14. DECLARATION OF CONFORMITY

DECLARATION OF CE CONFORMITY

Manufacturer:

FAST ČR, a. s.

Černokostelecká 2111, 100 00 Prague 10, Czech Republic

Tax ID number: CZ26726548

Product/brand: ELECTRIC SHREDDER / FIELDMANN

Type/model: FZD 5015-E

230–240 V~, 50 Hz, 2800 W

This product meets the requirement of the directives and regulations below:

ES Council Directive No. 2006/42/ES for machinery

ES Directive No. 2014/30/EU for electromagnetic compatibility (EMC)

ES Directive No. 2011/65/EU on the reduction of hazardous substances in electrical and

electronic equipment

and norms:

EN 62233:2008

EN 55014-1:2006+A2+A1

EN 55014-2/A2:2008

EN 61000-3-2:2014

N 6100-3-11:2000

EN 50434:2014

EN 60335-1:2012+A11

CE mark: 16

Place of issue: Prague Name: Ing. Zdeněk Pech

Board Chairman

Date of issue: 1. 8. 2016 Signature:

CZ

ZAHRADNÍ ŠTEPKOVAČ NÁVOD K OBSLUZE

19

Obsah

Zahradní štěpkovač

NÁVOD K OBSLUZE

Vážená zákaznice, vážený zákazníku,

děkujeme mnohokrát za projevenou důvěru!

Před prvním uvedením přístroje do provozu si bezpodmínečně přečtěte tento návod na

obsluhu! Naleznete v něm všechny pokyny pro bezpečné používání a dlouhou životnost

přístroje. Bezpodmínečně dodržujte všechny bezpečnostní pokyny, uvedené v tomto návodu!

OBSAH

1. VŠEOBECNÉ BEZPEČNOSTNÍ PŘEDPISY ........................................................................................................20

Důležitá bezpečnostní upozornění .................................................................................................................20

Obal ..................................................................................................................................................................................20

Návod k použití ...........................................................................................................................................................20

2. SYMBOLY ........................................................................................................................................................................21

3. DŘÍVE NEŽ ZAČNETE… .............................................................................................................................................22

Použití přiměřené určení .......................................................................................................................................22

4. PRO VAŠI BEZPEČNOST ..........................................................................................................................................22

Všeobecné bezpečnostní pokyny ..................................................................................................................22

Elektrická bezpečnost ............................................................................................................................................23

Údržba .............................................................................................................................................................................23

Upozornění speciﬁ cká pro přístroj ...................................................................................................................23

5. POPIS STROJE...............................................................................................................................................................25

Popis stroje (viz Obr. 1) ............................................................................................................................................25

6. SESTAVENÍ ŠTĚPKOVAČE ........................................................................................................................................26

7. OBSLUHA ŠTĚPKOVAČE ..........................................................................................................................................28

Zapnutí a vypnutí štěpkovače (Obr. 5) .........................................................................................................28

Přepínač vpřed / zpětný chod (Obr. 5, bod 3) .........................................................................................28

Ochrana proti přetížení ..........................................................................................................................................28

Záchytná nádoba ....................................................................................................................................................29

Kryt řezného válce (Obr. 1, bod 11) .................................................................................................................29

8. NASTAVENÍ A PRÁCE SE ŠTĚPKOVAČEM ..................................................................................................... 30

Nastavení vzdálenosti protinože ..................................................................................................................... 30

Před zapnutím ............................................................................................................................................................ 30

Materiál, který může štěpkovač zpracovávat ......................................................................................... 30

Štěpkovač NESMÍ zpracovávat následující typy materiálů: ............................................................ 30

9. PROVOZ ..........................................................................................................................................................................31

10. ÚDRŽBA ...........................................................................................................................................................................31

11. ŘEŠENÍ PROBLÉMŮ ....................................................................................................................................................32

12. TECHNICKÉ ÚDAJE ....................................................................................................................................................33

13. LIKVIDACE ......................................................................................................................................................................33

14. PROHLÁŠENÍ O SHODĚ ..........................................................................................................................................34

CZ 20

FZD 5015 E

Všeobecné bezpečnostní předpisy

1. VŠEOBECNÉ BEZPEČNOSTNÍ PŘEDPISY

Důležitá bezpečnostní upozornění

Výrobek pečlivě vybalte a dejte pozor, abyste nevyhodili žádnou část obalového materiálu dříve, než

najdete všechny součásti výrobku.

Výrobek uchovávejte na suchém místě mimo dosah dětí.

Čtěte všechna upozornění a pokyny. Zanedbání při dodržování varovných upozornění a pokynů mohou mít

za následek úraz elektrickým proudem, požár a/nebo těžká poranění.

Obal

Výrobek je umístěn v obalu bránícím poškozením při transportu. Tento obal je surovinou a lze jej proto

odevzdat k recyklaci.

Návod k použití

Než začnete se strojem pracovat, přečtěte si následující bezpečnostní předpisy a pokyny k používání.

Seznamte se s obslužnými prvky a správným používáním zařízení. Návod pečlivě uschovejte pro případ

pozdější potřeby. Minimálně po dobu záruky doporučujeme uschovat originální obal včetně vnitřního balicího

materiálu, pokladní doklad a záruční list. V případě přepravy zabalte stroj zpět do originální krabice od výrobce,

zajistíte si tak maximální ochranu výrobku při případném transportu (např. stěhování nebo odeslání do

servisního místa).

POZNÁMKA: Předáváte-li stroj dalším osobám, předejte jej společně s návodem. Dodržování

přiloženého návodu k obsluze je předpokladem řádného používání stroje. Návod k obsluze obsahuje

rovněž pokyny pro obsluhu, údržbu a opravy.

Výrobce nepřebírá odpovědnost za nehody nebo škody vzniklé následkem

nedodržování tohoto návodu.

Stránka sa načítava...

Fieldmann FZD 5015 E Používateľská príručka

Fieldmann FZD 5015 E Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty