Philips GC1930/02 Používateľská príručka

GC1900 series

2

3

A B C D E F G IH J

N

K

O

M

L

1

4

GC1900 series

ENGLISH 6

 18

 32

 44

 56

 68

 80

 93

 106

 119

 132

 144

 158

 171

 183

 196

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/welcome.

General description (Fig. 1)

 Spray nozzle (all types except GC1903/GC1910)

B Cap of lling opening

C Steam control

- O= no steam

- small cloud = minimum steam

- large cloud = maximum steam

- x = Calc-clean position

D Spray button 8 (all types except GC1903/GC1910)

E Steam boost button \ (all types except GC1903/GC1905/GC1910/

GC1920)

F Automatic shut-off light (GC1990/GC1991 only)

G Temperature dial

H Double-Active Calc System (all types except GC1903/GC1905/

GC1910/GC1920)

I Temperature light

J Mains cord

 Type plate

L Water tank

M MAX water level indication

N Soleplate

O Heat-resistant storage cover (GC1981/1991 only)

Important

Read this user manual carefully before you use the appliance and save it

for future reference.

Danger

- Never immerse the iron in water.

ENGLISH

Warning

- Check if the voltage indicated on the appliance corresponds to the

local mains voltage before you connect the appliance.

- Do not use the appliance if the plug, the mains cord or the appliance

itself shows visible damage, or if the appliance has been dropped

or leaks.

- If the mains cord is damaged, you must have it replaced by Philips, a

service centre authorised by Philips or similarly qualied persons in

order to avoid a hazard.

- Never leave the appliance unattended when it is connected to the

mains.

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

- Children should be supervised to ensure that they do not play with

the appliance.

- Do not let the mains cord come into contact with the hot soleplate

of the iron.

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord regularly for possible damage.

- The soleplate of the iron can become extremely hot and may cause

burns if touched.

- When you have nished ironing, when you clean the appliance, when

you ll or empty the water tank and also when you leave the iron

even for a short while: set the steam control to position O, put the

iron on its heel and remove the mains plug from the wall socket.

- Always place and use the iron on a stable, level and horizontal

surface.

- Do not put perfume, vinegar, starch, descaling agents, ironing aids or

other chemicals in the water tank.

- This appliance is intended for household use only.

ENGLISH 7



This Philips appliance complies with all standards regarding

electromagnetic elds (EMF). If handled properly and according to the

instructions in this user manual, the appliance is safe to use based on

scientic evidence available today.



1 Remove any sticker or protective foil from the soleplate.

2 Let the iron heat up to maximum temperature and pass the iron

over a piece of damp cloth for several minutes to remove any

residues from the soleplate.





This iron is designed to be used with tap water.

If the tap water in your area is very hard, we advise you to mix it with an

equal amount of distilled water. Do not use distilled water only.

Do not put perfume, vinegar, starch, descaling agents, ironing aids,

chemically descaled water or other chemicals in the water tank.

1 Switch off the appliance and unplug it.

2 Set the steam control to position O (= no steam) (Fig. 2).

3 Openthecapofthellingopening(Fig.3).

4 Tilttheironandllthewatertankuptomaximumlevelunderthe

tap (Fig. 4).

Note: Do not ll the water tank beyond the MAX indication.

5 Closethecapofthellingopening(‘click’).

ENGLISH8

Selecting temperature and steam setting

Fabric type Temperature

setting

Steam

setting

Steam

boost

(specic

types only)

Spray

(specic

types

only)

Linen MAX large

cloud

Yes \ Yes 8

Cotton 3 large

cloud

Yes \ Yes 8

Wool 2 small

cloud

No

Yes 8

Silk 1 O No No

Synthetic

fabrics (e.g.

Acrylic, nylon,

polyamide,

polyester).

1 O No No

Check the laundry care label of the article to be ironed to determine the

required ironing temperature.

If you do not know what kind or kinds of fabric an article is made of,

determine the right ironing temperature by ironing a part that is not

visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric to

prevent shiny patches. Avoid using the spray function to prevent stains.

1 To set the appropriate ironing temperature, turn the temperature

dial to the appropriate position (see the table above) (Fig. 5).

2 Put the iron on its heel.

3 Put the mains plug in an earthed wall socket.

, The temperature light goes on.

ENGLISH 9

Do not set the steam control to a steam setting if you have set a

low ironing temperature (below 2/ WOOL setting) or when the iron

is still heating up (as long as the temperature light is on). Otherwise

water will leak from the iron.

4 When the temperature light goes out, wait a while before you start

ironing.

, During ironing, the temperature light goes on from time to time.

This indicates that the iron is heating up to the set temperature.

5 Set the appropriate steam setting. Make sure that the steam setting

you select is suitable for the set ironing temperature:

- O for no steam (for all temperature settings). (Fig. 2)

- small cloud for minimum steam (temperature settings 2 and

3. (Fig. 6)

- large cloud for maximum steam (temperature settings 3 to

MAX. (Fig. 7)

Features



You can use the spray function at any temperature to moisten the article

to be ironed. This helps remove stubborn creases.

1 Make sure that there is enough water in the water tank.

2 Press the spray button several times to moisten the article to be

ironed (Fig. 8).



A powerful boost of steam helps to remove very stubborn creases.

The steam boost function only works at temperature settings between

3 and MAX.

1 Press and release the steam boost button (Fig. 9).

ENGLISH10



You can also use the steam boost function when you hold the iron in

vertical position. This is useful for removing creases from hanging clothes,

curtains etc.

1 Hold the iron in vertical position and press and release the steam

boost button (Fig. 10).

Never direct the steam at people.



The automatic shut-off function automatically switches off the iron if it

has not been moved for a while.

, Theautomaticshut-offlightashestoindicatethattheironhas

been switched off by the automatic shut-off function (Fig. 11).

To let the iron heat up again:

1 Pick up the iron or move it slightly.

, Theautomaticshut-offlightstopsashing.

, If the temperature of the soleplate has dropped below the set

ironing temperature, the temperature light goes on.

2 If the temperature light goes on after you have moved the iron,

wait for it to go out before you start ironing.

Note: If the temperature light does not go on after you move the iron, the

soleplate still has the right temperature and the iron is ready for use.

Cleaning and maintenance

Cleaning

1 Set the steam control to position O, remove the plug from the wall

socket and let the iron cool down.

2 Pour any remaining water out of the water tank.

3 Wipeakesandanyotherdepositsoffthesoleplatewithadamp

cloth and a non-abrasive (liquid) cleaning agent.

ENGLISH 11

To keep the soleplate smooth, avoid hard contact with metal objects.

Never use a scouring pad, vinegar or other chemicals to clean the

soleplate.

4 Clean the upper part of the iron with a damp cloth.

5 Regularly rinse the water tank with water. Empty the water tank

after you have rinsed it (Fig. 12).



Note: See chapter ‘General description’ for the type numbers that are

equipped with the Double-Active Calc System.

The Double-Active Calc System consists of an Anti-Calc tablet inside the

water tank combined with the Calc-Clean function.

- The Anti-Calc tablet prevents scale from clogging the steam vents.

The tablet is constantly active and does not need to be

replaced (Fig. 13).

- The Calc-Clean function removes scale particles from the iron.



Use the Calc-Clean function once every two weeks. If the water in your

area is very hard (i.e. when akes come out of the soleplate during

ironing), use the Calc-Clean function more frequently.

1 Make sure the appliance is unplugged.

2 Set the steam control to position O.

3 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the water tank.

4 Set the temperature dial to MAX (Fig. 14).

5 Put the mains plug in an earthed wall socket.

6 Unplug the iron when the temperature light goes out.

7 Hold the iron over the sink and turn the steam control to the

Calc-Clean position x. (Fig. 15)

ENGLISH12

8 Pull the steam control slightly upwards and gently shake the iron

until all water in the tank has been used up (Fig. 16).

, Steam and boiling water come out of the soleplate. Scale (if any) is

ushedout.

9 After you have used the Calc-Clean function, press down the steam

control while you turn it to position O. (Fig. 17)

Note: Repeat the Calc-Clean process if the water that comes out of the iron

still contains scale particles.



1 Put the plug in the wall socket and let the iron heat up to let the

soleplate dry.

2 Unplug the iron when the temperature light goes out.

3 Move the iron gently over a piece of used cloth to remove any

water stains that may have formed on the soleplate.

4 Let the iron cool down before you store it.



1 Pull the steam control out of the appliance. (Fig. 18)

2 Use vinegar to remove scale, if any, from the needle (Fig. 19).

Do not bend or damage the steam control needle.

3 Reinsert the steam control. Place the point of the needle exactly in

thecentreoftheholeandtthesmallprojectiononthesideof

the needle into the slot (Fig. 20).

4 Set the steam control to position O.

Storage

1 Set the steam control to position O and remove the plug from the

wall socket.

2 Wind the mains cord round the cord storage facility (Fig. 21).

ENGLISH 13

3 Specictypesonly:puttheironintheheat-resistantstoragecover

and fasten the cover with the Velcro strips (Fig. 22).

Note: If you use the heat-resistant soleplate cover, you do not have to let the

iron cool down rst. If you want to store the iron without the soleplate cover,

let it cool down rst.



- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the

environment (Fig. 23).



If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the

worldwide guarantee leaet). If there is no Consumer Care Centre in

your country, go to your local Philips dealer.



This chapter summarises the most common problems you could

encounter with the appliance. If you are unable to solve the problem with

the information below, contact the Consumer Care Centre in your

country.

Problem Possible cause Solution

The iron is

plugged in, but

the soleplate

is cold.

There is a

connection

problem.

Check the mains cord, the plug

and the wall socket.

The temperature

dial is set to MIN.

Set the temperature dial to the

required position.

ENGLISH14

Problem Possible cause Solution

The iron does

not produce

any steam.

There is not

enough water in

the water tank.

Fill the water tank (see chapter

‘Using the appliance’, section

‘Filling the water tank’).

The steam control

is set to position O.

Set the steam control to the

small cloud or large cloud (see

chapter ‘Using the appliance,

section ‘Selecting temperature

and steam setting’).

The steam

boost function

does not

work properly

(specic types

only).

You have used the

steam boost

function too often

within a very short

period.

Put the iron on its heel or

continue ironing in horizontal

position and wait a while before

you use the steam boost

function again.

The iron is not hot

enough.

Set an ironing temperature at

which the steam boost function

can be used ( 3 to MAX).

Put the iron on its heel and wait

until the temperature light goes

out before you use the steam

boost function.

Flakes and

impurities

come out of

the soleplate

during ironing.

Hard water forms

akes inside the

soleplate.

Use the Calc-Clean function

one or more times (see chapter

‘Cleaning and maintenance’,

section ‘Calc-Clean function’).

ENGLISH 15

Problem Possible cause Solution

The light on

the handle

ashes

(specic types

only).

The automatic

shut-off function

has been activated

(see chapter

‘Features’, section

‘Automatic shut-

off’).

Pick up the iron or move it

slightly to deactivate the

automatic shut-off function. The

automatic shut-off light goes out.

Water

droplets drip

on the fabric

during ironing.

You have not

closed the cap of

the lling opening

properly.

Press the cap until you hear a

click.

The set

temperature is too

low for steam

ironing.

Set an ironing temperature that

is suitable for steam ironing (

2 to MAX). Put the iron on its

heel and wait until the

temperature light goes out

before you start ironing.

You have put an

additive in the

water tank.

Rinse the water tank and do not

put any additive in the water

tank.

Specic types only:

you have used the

steam boost

function at a setting

below 3.

Set the temperature dial to a

setting between 3 and

MAX.

Specic types only:

you have used the

steam boost

function too often

within a short

period.

Put the iron on its heel or

continue ironing in horizontal

position and wait a while before

you use the steam boost

function again.

ENGLISH16

Problem Possible cause Solution

Water drips

from the

soleplate after

the iron has

cooled down

or has been

stored.

You have put the

iron in horizontal

position while there

was still water in

the water tank.

Empty the water tank and set

the steam control to position O

after use. Store the iron on its

heel.

Water spots

appear on the

garment

during ironing.

These wet spots

may be caused by

steam that has

condensed onto

the ironing board.

Iron wet spots without steam

from time to time to dry them.

If the underside of

the ironing board is

wet, wipe it dry

with a piece of dry

cloth.

To prevent steam from

condensing onto the ironing

board, use an ironing board with

a wire mesh top.

ENGLISH 17

18



Поздравления за вашата покупка и добре дошли във Philips! За да се

възползвате изцяло от предлаганата от Philips поддръжка,

регистрирайте продукта си на www.philips.com/welcome.



 Дюза за пръскане (всички модели, освен GC1903/GC1910)

B Капачка на отвора за пълнене

C Регулиране на парата

- О = без пара

- малък облак = минимална пара

- голям облак = максимална пара

- x = положение Calc-clean (премахване на накип)

D Бутон за пръскане 8 (всички модели, освен GC1903/GC1910)

E Бутон за допълнителна пара \ (всички модели, освен GC1903/

GC1905/GC1910/GC1920)

F Светлинен индикатор за автоматично изключване (само за

GC1990/GC1991)

G Температурен регулатор

H Система за премахване на накип с двойно действие (всички

модели, освен GC1903/GC1905/GC1910/GC1920)

I Светлинен температурен индикатор

J Захранващ кабел

 Табелка с данни

L Воден резервоар

M Обозначение MAX (МАКСИМАЛНО) за ниво на водата

N Гладеща повърхност

O Термоустойчив капак за съхранение (само за GC1981/1991)



Преди да използвате уреда, прочетете внимателно това

ръководство за експлоатация и го запазете за справка в бъдеще.



- Никога не потапяйте ютията във вода.





- Преди да свържете уреда към мрежата, проверете дали

посоченото върху уреда напрежение отговаря на напрежението

на местната електрическа мрежа.

- Не използвайте уреда, ако щепселът, захранващият кабел или

самият уред имат видими повреди, както и ако уредът е падал

или тече.

- Ако захранващият кабел се повреди, той трябва винаги да се

подменя от Philips, упълномощен сервиз на Philips или подобни

квалифицирани лица, за да се избегне опасност.

- Никога не оставяйте уреда без наблюдение, когато е включен в

контакт.

- Този уред не е предназначен за ползване от хора с намалени

физически усещания или умствени недостатъци или без опит и

познания, включително деца, ако са оставени без наблюдение и

не са инструктирани от страна на отговарящо за тяхната

безопасност лице относно начина на използване на уреда.

- Наглеждайте децата, за да не си играят с уреда.

- Не допускайте захранващият кабел да се допира до горещата

гладеща плоча на ютията.



- Включвайте уреда само в заземен мрежов контакт.

- Проверявайте редовно за евентуални повреди на захранващия

кабел.

- Гладещата плоча на ютията може да се нагорещи много и да

причини изгаряне при докосване.

- Когато сте свършили с гладенето, когато почиствате уреда,

когато пълните или изпразвате резервоара за вода, а също така

когато оставяте ютията дори за момент: поставете регулатора

на парата в положение О, поставете ютията върху петата й и

изключете щепсела от контакта.

- Винаги поставяйте и използвайте ютията върху хоризонтална,

равна и стабилна повърхност.

- Не сипвайте във водния резервоар парфюм, оцет, кола, препарати

за отстраняване на накип, помощни препарати за гладене или

други химикали.

 19

- Този уред е предназначен само за битови цели.



Този уред Philips е в съответствие с всички стандарти по отношение

на електромагнитните излъчвания (EMF). Ако се употребява

правилно и съобразно напътствията в Ръководството, уредът е

безопасен за използване според наличните досега научни факти.



1 Свалетевсякаквилепенкиилизащитнофолиоотгладещата

плоча.

2 Загрейтеютиятадомаксималнатемператураигладетев

продължениенаняколкоминутивърхувлажнакърпа,зада

отстранитевсякаквиостатъциотгладещатаплоча.





Ютията е предназначена за използване с чешмяна вода.

Ако чешмяната вода във вашия район е много твърда, препоръчваме

ви да я смесите с равно количество дестилирана вода. Не

използвайте само дестилирана вода.

Несипвайтевъвводниярезервоарпарфюм,оцет,кола,препарати

заотстраняваненанакип,помощнипрепаратизагладене,

химическидекалциранаводаилидругихимикали.

1 Изключетеуредаиизведетещепселаотконтакта.

2 ПоставетерегулаторанапаратавположениеО(=без

пара)(фиг.2).

3 Отворетекапачкатанаотворазапълнене(фиг.3).

4 Наклонетеютиятаинапълнетерезервоарасводадо

максималнотонивоподкрана(фиг.4).

Забележка: Не пълнете водния резервоар над знака MAX.

20

Stránka sa načítava ...

Philips GC1930/02 Používateľská príručka

Táto príručka je tiež vhodná pre

Philips GC1930/02 Používateľská príručka

V iných jazykoch

Súvisiace články