Parkside 104387 Operation and Safety Notes

Kategória
Elektrické náradie
Typ
Operation and Safety Notes

Táto príručka je tiež vhodná pre

IAN 104387
BELT SANDER PBS 900 B1
BANDSCHLEIFER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
BELT SANDER
Operation and Safety Notes
Translation of the original instructions
SZLIFIERKA T AŚMOW A
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
TRAČNI BRUSILNIK
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
PÁSOV Á BRUSKA
Pokyny pro obsluhu a bezpečnostní pokyny
Překlad originálního provozního návodu
PÁSOV Á BRÚSKA
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
SZALAGCSISZ OLÓ
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 15
HU Kezelési és biztonsági utalások Oldal 25
SI Navodila za upravljanje in varnostna opozorila Stran 37
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 47
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 57
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 67
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funk cjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funk cióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
D E
12
A
9
6
1
4
7 8
5
2
3
B
6
C
10
11 13
5 GB
Table of contents
Introduction
Proper use ...........................................................................................................................................Page 6
Features and equipment .....................................................................................................................Page 6
Included items .....................................................................................................................................Page 6
Technical information .........................................................................................................................Page 6
General power tool safety warnings
1. Work area safety ...........................................................................................................................Page 7
2. Electrical safety ..............................................................................................................................Page 7
3. Personal safety ...............................................................................................................................Page 7
4. Power tool use and care ................................................................................................................Page 8
5. Service ............................................................................................................................................Page 8
Safety advice for belt sanders...........................................................................................................Page 8
Preparing for use
Tensioning / changing the sanding belt ............................................................................................Page 9
Advice on use .....................................................................................................................................Page 9
Vacuum dust extraction ......................................................................................................................Page 10
Operation
Switching on and off ..........................................................................................................................Page 10
Selecting the correct rotational speed and sanding belt ................................................................Page 10
Stationary use .....................................................................................................................................Pag e 11
Tips and tricks .....................................................................................................................................Pag e 11
Maintenance and cleaning .............................................................................................. Page 12
Service centre .............................................................................................................................Page 12
Warranty ........................................................................................................................................Page 12
Disposal ............................................................................................................................................ Page 12
Translation of the original declaration of conformity /
Manufacturer ..............................................................................................................................Page 13
6 GB
Introduction
Belt sander PBS 900 B1
Q
Introduction
Congratulations on your purchase. You have select-
ed a high quality product. The instructions for use
are a part of this product. They contain important
information about safety, use and disposal. Before
using the product, please familiarise yourself with all
the operating and safety instructions. Use the product
only as described and for the specified applications.
When passing this product on to others please be
sure to also include all of its documentation.
Q
Proper use
The belt sander is designed for dry sanding of large
surfaces of wood, plastic, metal, plaster and painted
surfaces. The device may only be used for dry sand-
ing. Always use a sanding belt and grade of grit
suitable for the particular surface you are sanding.
The speed selected should also be appropriate for
the material. The device is not intended for commer-
cial use. Any other use or modification to the device
shall be considered as improper use and could give
rise to considerable dangers. The manufacturer will
not accept liability for loss or damage arising from
improper use.
Q
Features and equipment
1
Belt speed adjuster wheel
2
Locking knob
3
ON / OFF switch
4
Toothed belt cover
5
Dust extraction spout
6
Belt adjuster screw
7
Auxiliary handle
8
Ventilation slots
9
Tensioning lever
10
Dust collection box
11
Extraction adapter
12
Screw clamps 2 x
13
Reducer
Q
Included items
Check that all the items and accessories
are present immediately after unpacking
the device:
1 Belt sander PBS 900 B1
1 Sanding belt
1 Dust collection box
1 Extraction adapter
(for external vacuum dust extraction)
2 Screw clamps
1 Reducer
1 Operating instructions
Q
Technical information
Belt sander: Parkside PBS 900 B1
Nominal voltage: 230 V∼, 50 Hz
Nom. power input: 900 W
No-load belt speed: 240–400 m / min
No-load speed: n
0
450–750 U / min
Sanding belt 75 x 533 mm
Protection class: II /
Noise and vibration data:
Measured values for noise are determined in accor-
dance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 92.22 dB(A)
Sound power level: 103.22 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Total vibration, EN 60745:
Vibration emission value
Rear handle: a
h
= 4.181 m / s
2
Front handle: a
h
= 6.115 m / s
2
Uncertainty K = 1.5 m / s
2
Introduction / General power tool safety warnings
7 GB
Introduction
Introduction / General power tool safety warnings
The vibration level given in these
operating instructions has been measured in a pro-
cedure according to EN 60745 and can be used
for the comparison of appliances. The vibration
emission value specified can also serve as a prelim-
inary assessment of the exposure.
Different uses of the device give rise to different vi-
bration levels and in many cases they may exceed
the values given in these instructions. It is easy to un-
derestimate the vibration load if the electrical power
tool is used regularly in particular circumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particul
ar
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General power tool
safety warnings
Read all safety
warnings and all instructions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and / or
serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-op-
erated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) D
o not operate power tools in explosive
atmospheres, such as in the presence
of flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractio
ns
can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plug
s
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk
of electric shock.
e)
When operating a power tool outdo
ors,
use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing
and use common sense when operat-
ing a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medica-
tion. A moment of inattention while operating
power tools may result in serious personal injury.
8 GB
General power tool safety warnings
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal in-
juries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and / or
battery pack, picking up or carrying
the tool. Carrying power tools with your fing
er
o
n the switch or energising power tools that hav
e
the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper foot-
ing and balance at all times. This enables
better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from mov-
ing parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your applica
tion.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and / or the battery pack from
the power tool before making any ad-
justments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of un-
trained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other con-
dition that may affect the power tool’s
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Service
a) Have your power tool serviced by a
qualified repair person using only
iden-
tical replacement parts. This will ensure
that the safety of the power tool is maintained.
Q
Safety advice for
belt sanders
Hold the device by the insulated han-
dle surfaces as the sanding belt could
strike the device’s own mains lead.
Damaging a live wire could result in the metal
parts of the device also becoming live and
could lead to an electric shock.
DANGER OF FIRE FROM FLYING SPARKS!
Sanding metal creates flying sparks. For this
reason, always make sure that nobody is placed
General power tool safety warnings / Preparing for use
9 GB
General power tool safety warnings
General power tool safety warnings / Preparing for use
in any danger and that there are no inflammable
materials near the working area.
When undertaking prolonged sanding of wood,
and in particular when working on materials
that give rise to dusts that are hazardous to
health, the sander must be connected to a
suitable external dust extraction device.
Ensure that there is adequate ventilation when
working on plastic, paint, varnish etc.
The belt sander is designed for the dry sanding
of large surfaces of wood, plastic, metal and
plaster and painted surfaces. The device is to
be used for dry sanding only.
Do not sand materials containing asbestos.
Asbestos is a known carcinogen.
POISONOUS DUSTS!
Sanding paints containing lead, some types of
wood and metal for example may give rise to
hazardous or poisonous dusts and represents a
risk to the health of the person operating the
device and to anyone near the work area.
Wear safety glasses and a dust protection mask!
Securely support the workpiece. Use clamps or
a vice to grip the workpiece firmly. This is much
safer than holding it with your hand.
Never support yourself by placing your hands
near or in front of the device or the workpiece
surface. A slip can result in injury.
If a dangerous situation arises, pull the mains
plug immediately out of the mains socket.
Always work with the mains lead leading
away from the rear of the device.
Avoid contact with the moving sanding belt.
Do not work on moistened materials or damp
surfaces.
Always switch on the device before placing it
against the workpiece. After sanding, lift the de-
vice from the workpiece before switching it off.
When working always hold the device securely
with both hands (see Fig. D). Always keep
proper footing and balance.
Switch the device off and allow it to come to
a complete standstill before you put it down.
When taking a break from your work, before
carrying out any tasks on the device itself (e.g.
changing the sanding belt) and when you are
not using the device, always pull the mains
plug out of the mains socket.
Q
Preparing for use
Q
Tensioning / changing
the sanding belt
RISK OF INJURY! Before
you carry out any work on the belt sander always
pull the plug out of the mains socket.
1. Then release the tensioner for the sanding belt
by moving the tensioning lever
9
fully outwards
(see fig. A). The tensioner is now open and the
sanding belt can be removed.
2. Next insert a new sanding belt or change the
belt for one suitable for a different material or
one with a different grit size.
IMPORTANT: The direction of the arrows on
the inside of the sanding belt must agree with
that on sander housing.
3. Press the tensioning lever
9
back into its
initial position.
Adjusting the sanding belt:
Pick up the device, switch it on and turn it over.
Adjust the belt tracking by turning the adjuster
screw
6
until the edge of the sanding belt is
flush with and runs parallel to the edge of the
device (Fig. B.).
IMPORTANT: Always make sure that the
sanding belt does not cut into the housing.
Check the sanding belt regularly and if neces-
sary re-adjust it using the adjuster screw
6
.
Q
Advice on use
Light sanding pressure is enough:
Apply light sanding pressure only. The weight of
the belt sander alone is adequate to produce
good sanding results. By adopting this approach
you will also prolong the life of your sanding
belts and obtain a smoother workpiece surface.
Sanding and surfaces:
The sanding output and the quality of the surface
finish obtained are determined by the belt speed
and the grade of grit on the sanding belt (see the
10 GB
section on “Selecting the correct rotational speed
and sanding belt”).
Sanding procedure:
With the sander switched on, bring it into con-
tact with the workpiece and move it forward
carefully. Work in parallel and overlapping
widths. Always work in the direction of the grain
to avoid undesirable transverse sanding marks.
After sanding always lift the device from the
workpiece before switching it off.
Q
Vacuum dust extraction
DANGER OF FIRE! There is
the danger of fire when working with electrical de-
vices that have a dustbox or can be connected to
a vacuum cleaner. Under certain conditions the
wood dust in the dust collection box (or in the vacu-
um‘s dust bag) may self-ignite, e.g. as a result of
flying sparks generated when abrading metals or
metal objects left in wood. This can happen par-
ticularly if the wood dust is mixed with paint residue
or other chemicals and the abraded particles are
hot from prolonged abrasion. Therefore you must
empty the device’s dust collection box and the vac-
uum cleaner’s dust bag before taking a break or
stopping work and always avoid overheating of
the abraded particles and the device.
Wear a dust mask!
Dust collection with dust collection box
(see Fig. C):
Push the dust collection box
10
into the desig-
nated fold on the side of the unit with the con-
necting piece
5
.
Remove / take out the dust collection box
Pull the dust collection box
10
out of the device.
Suction adapter (with reducer) (see Fig. C)
Connecting:
Slide the suction adapter
11
onto the connecting
piece
5
. If necessary, use the reducer
13
by
sliding it into the suction adapter
11
.
Slide the tube of an approved dust extraction
unit (e.g. a workshop vacuum) onto the suction
adapter
11
, if necessary using the reducer
13
.
Removal:
Pull the hose out of the dust extraction unit.
Pull out the suction adapter
11
, if necessary with
the reducer
13
.
Q
Operation
Q
Switching on and off
To switch on intermittent operation mode:
Press the ON / OFF switch
3
.
To switch off intermittent operation mode:
Release the ON / OFF switch
3
.
To switch on continuous operation mode:
Press the ON / OFF switch
3
, and keep it
pressed, then press the locking knob
2
.
To switch off continuous operation mode:
Press and then release the ON / OFF switch
3
.
Q
Selecting the correct rotational
speed and sanding belt
You can select the belt speed using the belt speed
adjuster wheel
1
even whilst the sander is running.
The optimum belt speed depends on the workpiece
and the workpiece material. Always confirm the best
speed by carrying out a small test. The following
table lists some recommended values to help you
determine the optimum speed.
Preparing for use / Operation
Operation
11 GB
Material / type of
work
Softwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 240
Preselected rotation
speed
high (5–6)
Material / type of
work
Hardwood
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 180
Preselected rotation
speed
high (5–6)
Material / type of
work
Chipboard
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) 150
Preselected rotation
speed
high (5–6)
Material / type of
work
Removing paint /
varnish
Coarse finish
(Grit grade)
60
Fine finish (Grit grade) ––
Preselected rotation
speed
high (5–6)
Material / type of
work
Sanding varnish
Coarse finish
(Grit grade)
150
Fine finish (Grit grade) 320
Preselected rotation
speed
low (1–2)
Material / type of
work
Rust removal
Coarse finish
(Grit grade)
40
Fine finish (Grit grade) 120
Preselected rotation
speed
medium / high (3–4)
Material / type of
work
Plastic
Coarse finish
(Grit grade)
120
Fine finish (Grit grade) 240
Preselected rotation
speed
low / medium (2–3)
Material / type of
work
Non-ferrous metals
(e.g. aluminium)
Coarse finish
(Grit grade)
80
Fine finish (Grit grade) 150
Preselected rotation
speed
medium / high (3–4)
Stationary use
Set the speed using the belt speed wheel
1
.
Turn the power tool as shown in figure E and
place on a sturdy worktop.
Attach two screw clamps
12
to the power tool
as shown and tighten.
Q Tips and tricks
Never use the same sanding belt to sand wood
and metal.
Worn or ripped sanding belts can damage
the workpiece. Change sanding belts at the
appropriate time.
Keep the sanding belt properly tensioned so
that it does not hang down too much and
become unusable due to nicks, creases etc.
Preparing for use / Operation
Operation
12 GB
Q
Maintenance and cleaning
RISK OF INJURY! Before
you carry out any work on the belt sander always
pull the mains plug out of the mains socket.
The belt sander is designed to be maintenance-free.
Clean the device frequently. This should be done
immediately after you have finished using it.
Use a dry cloth to clean the device - never use
petrol, solvents or cleaners that attack plastic.
Always keep the ventilation slots clear.
Remove any adhering dust with a narrow
paint brush.
Emptying / cleaning the dust collection box:
Pull the dust collection box
10
out of the device.
Tap the dust collection box
10
to empty it com-
pletely and reattach to the unit.
Always keep the vents clear.
Remove dust clinging to the sander with a brush.
Q
Service centre
Have your device
repaired only by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
If the plug or mains
lead needs to be replaced, always ha
ve
the replacement carried out by the
manufacturer or its service centre. This
will ensure that your device remains safe to use.
Note: Spare parts not listed (e.g. carbon brushes,
switches) can be ordered through our call centre.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for pri-
vate use only and is not intended for commercial use.
The warranty is void in the case of abusive and im-
proper handling, use of force and internal tampering
not carried out by our authorized service branch. Your
statutory rights are not restricted in any way by this
warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0.10 GBP/Min.)
IAN 104387
Q
Disposal
The packaging is wholly composed of
environmentally-friendly materials that can
be disposed of at a local recycling centre.
Do not dispose of electric tools
in the household waste!
In accordance with European Directive
2012 / 19 / EU
(covering waste electrical and electronic equipment)
and its transposition into national legislation, worn out
electrical power tools must be collected separately
and taken for environmentally compatible recycling.
Maintenance and Cleaning / Service centre / Warranty / Disposal
Disposal / Translation of the original declaration of conformity / Manufacturer
13 GB
Contact your local refuse disposal authority for more
details of how to dispose of your worn out electrical
devices.
Translation of the original
declaration of conformity /
Manufacturer
We, KOMPERNASS HANDELS GMBH, the person
responsible for documents: Mr Semi Uguzlu, BURG-
STRASSE 21, 44867 BOCHUM, GERMANY, hereby
declare that this product complies with the following
standards, normative documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
RoHS Directive
(2011 / 65 / EU)
Applicable harmonized standards
EN 60745-1: 2009+A11
EN 60745-2-4: 2009+A11
EN 55014-1: 2006+A1+A2
EN 55014-2: 1997+A1+A2
EN 61000-3-2: 2006+A1+A2
EN 61000-3-3: 2013
Type / Device description:
Belt sander PBS 900 B1
Date of manufacture: 05–2015
Serial number: IAN 104387
Bochum, 31.05.2015
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifications
in the course of product development.
Maintenance and Cleaning / Service centre / Warranty / Disposal
Disposal / Translation of the original declaration of conformity / Manufacturer
14
Spis zawartości
15 PL
Spis zawartości
Wstęp
ytkowanie zgodnie z przeznaczeniem .....................................................................................Strona 16
Wyposażenie ...................................................................................................................................Strona 16
Zakres dostawy ...............................................................................................................................Strona 16
Dane techniczne .............................................................................................................................. Strona 16
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 17
2. Bezpieczeństwo elektryczne .....................................................................................................Strona 17
3. Bezpieczeństwo osób .................................................................................................................Strona 18
4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ........................................ Strona 18
5. Serwis ...........................................................................................................................................Strona 19
Wskazówki dotyczące bezpieczeństwa dla szlifierki taśmowej ................................................Strona 19
Uruchomienie
Zamocowanie / wymiana taśmy szlifierskiej .................................................................................Strona 20
Wskazówki robocze........................................................................................................................Strona 20
Odsysanie pyłu ................................................................................................................................Strona 20
Obsługa
Załączanie i wyłączanie ................................................................................................................Strona 21
Wybór obrotów i taśmy szlifierskiej ...............................................................................................Strona 21
Praca stacjonarna ............................................................................................................................Strona 22
Dobre rady i triki ..............................................................................................................................Strona 22
Konserwacja i czyszczenie ...........................................................................................Strona 22
Serwis ............................................................................................................................................. Strona 23
Gwarancja .................................................................................................................................. Strona 23
Utylizacja .....................................................................................................................................Strona 23
Tłumaczenie oryginału Deklaracji zgodności WE / Producent ......Strona 24
16 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
Szlifierka taśmowa PBS 900 B1
Q
Wstęp
Gratulujemy zakupu nowego urządzenia. Tym sa-
mym zdecydowali się Państwo na zakup produktu
wysokiej jakości. Instrukcja obsługi jest częścią tego
produktu. Zawiera ona ważne wskazówki dotyczące
bezpieczeństwa, użytkowania iutylizacji. Przed
pierwszym użyciem produktu należy zapoznać się
ze wszystkimi wskazówkami dotyczącymi obsługi
ibezpieczeństwa. Używać produktu wyłącznie
zgodnie zjego poniżej opisanym przeznaczeniem.
Wprzypadku przekazania produktu innej osobie
należy dołączyć do niego całą jego dokumentację.
Q
Użytkowanie zgodnie
z przeznaczeniem
Szlifierka taśmowa jest zaprojektowana do szlifo-
wania na sucho powierzchni drewna, tworzywa
sztucznego, metalu i masy szpachlowej oraz
powierzchni lakierowanych. Urządzenia wolno
używać wyłącznie do szlifowania na sucho. Zwróć
uwagę na to, żeby do obróbki różnych materiałów
stosować odpowiednie arkusze szlifierskie o zróż-
nicowanej ziarnistości, a także na to, żeby również
dopasować obroty do materiału. Urządzenie nie
jest przewidziane do celów zarobkowych. Każde
inne zastosowanie maszyny lub przeprowadzenie
w niej zmian jest uznawane za niezgodne z prze-
znaczeniem i kryje w sobie poważne zagrożenie
nieszczęśliwym wypadkiem. Za szkody powstałe
wskutek sprzecznego z przeznaczeniem użytkowa-
nia producent nie ponosi żadnej odpowiedzialności.
Q
Wyposażenie
1
Kółko do nastawiania prędkości taśmy
2
Przycisk ustalający
3
WŁĄCZNIK / WYŁĄCZNIK
4
Pokrywa paska zębatego
5
Króciec odsysający
6
Śruba do regulacji przebiegu taśmy
7
Dodatkowy uchwyt
8
Szczeliny wentylacyjne
9
Dźwignia mocująca
10
Pojemnik na p
11
Adapter odsysający
12
Ściski 2 x
13
Złączka redukcyjna
Q
Zakres dostawy
Bezpośrednio po rozpakowaniu urządze-
nia należy sprawdzić zakres dostawy:
1 Szlifierka taśmowa PBS 900 B1
1 Taśma szlifierska
1 Pojemnik na p
1 Adapter odsysający (do zewnętrznego
odsysania pyłu)
2 Ściski
1 Złączka redukcyjna
1 Instrukcja obsługi
Q
Dane techniczne
Szlifierka taśmowa:
Parkside PBS 900 B1
Napięcie znamionowe: 230 V∼, 50 Hz
Pobór mocy znamionowy: 900 W
Bieg jałowy-Prędkość taśmy
: 240–400 m / min
Obroty na biegu jałowym: n
0
450–750 U / min
Taśma szlifierska: 75 x 533 mm
Klasa ochrony: II /
Informacje dotyczące hałasu i wibracji:
Wartość pomiarowa hałasu wyznaczona zgodnie
z EN 60745. Poziom hałasu elektronarzędzia wg
oceny A wynosi typowo:
Poziom ciśnienia hałasu: 92,22 dB(A)
Pozom mocy hałasu: 103,22 dB(A)
Niepewność pomiaru K: 3 dB
Zakładać ochronniki słuchu!
Wartości całkowite drgań, EN 60745:
Wartość emisji drgań
Uchwyt tylny: a
h
= 4,181 m / s
2
Uchwyt z przodu: a
h
= 6,115 m / s
2
Niepewność K = 1,5 m / s
2
17 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Podany w niniejszych in-
strukcjach poziom drgań wyznaczony został za
pomocą metody pomiarowej określonej w normie
EN 60745 i może zostać użyty do porównania
urządzeń. Podany poziom emisji drgań może b
wykorzystywany również do wstępnego oszaco-
wania przerw w działaniu.
Poziom drgań będzie się różnił w zależności od
zastosowania elektronarzędzia i w niektórych
przypadkach może przekroczyć wartość podaną
w niniejszej instrukcji. Obciążenie drganiami może
wydawać się mniejsze niż w rzeczywistości, jeśli
elektronarzędzie będzie regularnie używane ten
sposób.
Wskazówka: Celem dokładnego oszacowania
obciążenia wibracjami w okresie określonego
okresu czasu pracy należy uwzględnić również te
okresy, w których urządzenie jest wyłączone lub
wprawdzie jest włączone, ale w rzeczywistości nie
pracuje. Może to przyczynić się do znacznej redukcji
obciążenia wibracjami w całym okresie czasu pracy.
Ogólne wskazówki bezpie-
czeństwa dla elektronarzędzi
Przeczytaj
wszystkie wskazówki dotyczące
bezpieczeństwa oraz instrukcje!
Zaniedbania w przestrzeganiu wskazówek doty-
czących bezpieczeństwa oraz w przestrzeganiu
instrukcji mogą spowodować porażenie prądem
elektrycznym, pożar i / lub ciężkie obrażenia ciała.
Przechowuj na przyszłość wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje!
Używany we wskazówkach dotyczących bezpie-
czeństwa termin „narzędzie elektryczne“ odnosi s
do narzędzi elektrycznych zasilanych z sieci (z ka-
blem sieciowym) oraz do narzędzi elektrycznych
zasilanych
z akumulatorów (bez kabla sieciowego).
1. Bezpieczeństwo miejsca pracy
a) Utrzymywać stanowisko pracy w czy-
stości i dobrze oświetlone. Nieporządek
i nieoświetlone obszary robocze mogą prowa-
dzić do wypadków.
b) Nie pracuj przy użyciu urządzenia w
otoczeniu zagrożonym eksplozją, w
którym znajdują się palne ciecze, gazy
lub pyły. Urządzenia elektryczne wytwarza-
ją iskry, które mogą zapalić pył lub pary.
c) Podczas użytkowania urządzenia
elektrycznego trzymaj dzieci i inne
osoby z daleka od urządzenia. Przy
odchyleniu możesz stracić kontrolę nad urzą-
dzeniem.
2. Bezpieczeństwo elektryczne
a) Wtyk sieciowy urządzenia musi
pasować do wtykowego gniazdka
sieciowego. W żaden sposób nie wol-
no zmieniać wtyku sieciowego urzą-
dzenia. Nie używaj żadnych wtyków
adapterowych razem z urządzeniami
wyposażonymi w uziemienie ochron
ne.
Niezmienione wtyki sieciowe i pasujące wtykowe
gniazdka sieciowe zmniejszają ryzyko poraże-
nia prądem elektrycznym.
b) Unikaj kontaktu fizycznego z powier-
zchniami uziemionymi takimi jak
powierzchnie rur, grzejników, kuchni
elektrycznych i lodówek. Istnieje podwyż-
szone niebezpieczeństwo porażenia prądem
elektrycznym, gdy twoje ciało jest uziemione.
c) Trzymaj urządzenie z daleka od desz-
czu i wilgoci. Wniknięcie wody do urządzenia
elektrycznego zwiększa ryzyko porażenia prą-
dem elektrycznym.
d)
Nie używaj kabla sieciowego w
sposób
sprzeczny z jego przeznaczeniem, tj.
do noszenia urządzenia, zawieszania
urzą dzenie lub do wyciągania wtyku
sieciowego z wtykowego gniazdka
sieciowego. Trzymaj kabel z daleka
od gorąca, oleju, ostrych krawędzi
lub poruszających się części urządzeń.
Wstęp
18 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Uszkodzone lub poplątane kable zwiększają
ryzyko porażenia prądem elektrycznym.
e)
Gdy pracujesz z urządzeniem elektrycz-
nym na dworze używaj wyłącznie
przedłużaczy, które są dopuszczone
również do pracy na dworze. Użycie
przedłużacza przystosowanego do stosowania
na dworze zmniejsza ryzyko porażenia prądem
elektrycznym.
f) Jeśli praca elektronarzędzia w otocze-
niu wilgotnym jest nie do uniknięcia,
należy zastosować wyłącznik prądu
uszkodzeniowego. Zastosowanie wyłącz-
nika prądu uszkodzeniowego zapobiega nie-
bezpieczeństwu porażenia prądem elektrycz
nym.
3. Bezpieczeństwo osób
a) Bądź stale uważny, zwracaj uwagę na
to co robisz i postępuj rozsądnie w trak-
cie pracy z narzędziem elektrycznym.
Nie używaj narzędzia, gdy jesteś zmę-
c
zony lub znajdujesz się pod wpływem
narkotyków, alkoholu lub lekarstw.
Chwila nieuwagi przy użytkowaniu urdzenia
może prowadzić do poważnych obrażeń ciała
.
b) Noś osobiste wyposażenie ochronne i
zawsze okulary ochronne. Noszenie
osobistego wyposażenia ochronnego takiego
jak maska przeciwpyłowa, buty antypoślizgo
we,
kask ochronny lub ochrona słuchu stosownie do
sposobu użytkowania narzędzia elektrycznego
zmniejsza ryzyko obrażeń ciała.
c) Unikaj niezamierzonego uruchomienia.
Upewnij się, że narzędzie elektryczne
jest wyłączone zanim podłączysz je
do zasilania prądowego, uchwycisz je
lub będziesz je przenosił. Jeżeli podczas
przenoszenia urządzenia będziesz trzym
palec na przełączniku WŁĄCZ. / WYŁĄCZ.
lub jeżeli urządzenie jest włączone, to może
to prowadzić do nieszczęśliwych wypadków.
d) Usuń narzędzia do nastawiania urzą-
dzenia lub klucze płaskie zanim włą-
czysz urządzenie. Narzędzie lub klucz,
który znajduje się w obracającej się części
urządzenia może prowadzić do obrażeń ciała.
e) Unikaj nienormalnej postawy ciała.
Zadbaj o pewne stanowisko i w każdej
chwili utrzymuj równowagę. Dzięki temu
będziesz mógł lepiej kontrolować urządzenie,
zwłaszcza w nieoczekiwanych sytuacjach.
f) Noś odpowiednią odzież. Nie noś ob-
szernej odzieży ani biżuterii. Trzymaj
włosy, odzież i rękawice z daleka od
poruszających się części. Luźna odzież,
biżuteria lub długie włosy mogą zostać uchwy-
cone przez poruszające się części.
g) Jeżeli zostaną zamontowane urzą-
dzenia do odsysania i wychwytywania
pyłu, to upewnij się, że są one podłą-
czone i że będą prawidłowo używane.
Używanie tych urządzeń zmniejsza zagrożenie
wywoływane pyłem.
4. Staranne obchodzenie
się i użytkowanie narzędzi
elektrycznych
a) Nie przeciążaj urządzenia. Używaj
do swojej pracy przeznaczonego do
niej narzędzia elektrycznego. Za pomo-
cą odpowiedniego narzędzia elektrycznego
pracujesz lepiej i bezpieczniej w danym zakre-
sie robót.
b) Nie używaj żadnego narzędzia elek-
trycznego, którego przełącznik jest
uszkodzony. Narzędzie elektryczne, które
nie daje się już więcej włączyć lub wyłączyć,
jest niebezpieczne i musi zostać naprawione.
c) Zanim przeprowadzisz nastawy urzą-
dzenia, wymienisz części osprzętu lub
odłożysz urządzenie wyciągnij wtycz-
kę sieciową z sieciowego gniazdka
wtykowego. Ten środek ostrożności zapo-
biega niezamierzonemu startowi urządzenia.
d) Przechowuj nieużywane narzędzia
elektryczne poza zasięgiem dzieci. Nie
pozwól na użytkowanie urządzenia
osobom, które nie są z nim obznajo-
mione lub nie przeczytały niniejszych
instrukcji. Narzędzia elektryczne są niebez-
pieczne, gdy są używane przez osoby niedo-
świadczone.
19 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
e) Pielęgnuj starannie urządzenie.
Sprawdź, czy ruchome części urzą-
dzenia funkcjonują nienagannie i nie
zakleszczają się, czy części urządzenia
nie są złamane lub uszkodzone w ta-
kim stopniu, że funkcjonowanie urzą-
dzenia jest uszczuplone. Zleć napra
uszkodzonych części przed użyciem
urządzenia. Przyczyną wielu wypadków są
źle konserwowane narzędzia elektryczne.
f) Utrzymuj narzędzia tnące w stanie
ostrym i czystym. Starannie pielęgnowane
narzędzia tnące o ostrych krawędziach tnących
mniej zakleszczają się i dają się łatwiej prowadzić.
g) Używaj narzędzia elektrycznego,
osprzętu, narzędzi wymiennych itp.
odpowiednio do niniejszych instrukcji
i w taki sposób, jaki jest zalecany dla
tego specjalnego typu urządzenia.
Uwzględniaj przy tym warunki robo-
cze i wykonywane czynności. Użycie
narzędzi elektrycznych do innych zastosow
niż to przewidziano może prowadzić do nie-
bezpiecznych sytuacji.
5. Serwis
a) Urządzenie oddawać do naprawy tyl-
ko wykwalifikowanemu personelowi
fachowemu i tylko z użyciem oryginal-
nych części zamiennych. To sposób na
zapewnienie bezpieczeństwa urządzenia.
Q
Wskazówki dotyczące bezpie-
czeństwa dla szlifierki taśmowej
Niniejsze urządzenie należy trzymać
na
izolowanych powierzchniach uchwytόw
,
jako że taśma szlifierska może uszko-
dzić własny przewόd sieciowy. Uszko-
dzenie przewodόw przewodzących prąd elek-
tryczny może spowodować, że metalowe części
urządzenia znajdą się pod napięciem oraz do-
prowadzić do porażenia prądem elektrycznym.
ZAGROŻENIE POŻAROWE WSKUTEK
WYRZUCANIA ISKIER! Gdy szlifowane są
metale postaje wyrzut iskier. Dlatego też należy
bezwzględnie zwracać uwagę na to, żeby nie
zostały zagrożone żadne osoby oraz żeby w
pobliżu obszaru roboczego nie znajdowały się
żadne palne materiały.
Przy obróbce drewna, a zwłaszcza, gdy obra-
biane będą materiały, w przypadku których
powstają szkodliwe dla zdrowia pyły, należy
podłączyć odpowiednie zewnętrzne urządzenie
odsysające.
Przy obróbce tworzyw sztucznych, farb,
lakierów itp. należy zadbać o wystarczające
napowietrzanie.
Szlifierka taśmowa jest zaprojektowana do szli-
fowania powierzchniowego na sucho drewna,
tworzywa sztucznego, metalu i masy szpachlowej
oraz powierzchni lakierowanych. Urządzenie
wolno stosować tylko do szlifu suchego.
Materiału zawierającego azbest nie wolno ob-
rabiać. Azbest jest uznawany za rakotwórczy.
TRUJACE PY! Powsta-
jące przy szlifowaniu na przykład powłok ma-
larskich zawierających ołów, niektórych rodzajów
drewna oraz metali szkodliwe / trujące pyły
stanowią zagrożenie zdrowia dla osoby obsłu-
gującej urządzenie lub dla osób znajdujących
się w pobliżu.
Noś okulary ochronne i maskę przeciwpyłową!
Zabezpieczaj przedmiot obrabiany. Używaj
urządzenia mocującego / imadła, aby przy-
trzymać przedmiot obrabiany. W ten sposób
jest on przytrzymywany pewniej niż ręką.
W żadnym wypadku nie opieraj rąk obok lub
przed urządzeniem oraz przed obrabianą
powierzchnią, ponieważ w razie ześlizgnięcia
istnieje niebezpieczeństwo obrażeń ciała.
W przypadku niebezpieczeństwa wyciągnij
natychmiast wtyczkę sieciową z wtykowego
gniazdka sieciowego.
Zawsze prowadź kabel od urządzenia do tyłu.
Unikaj kontaktu z biegnącą taśmą szlifierską.
Nie obrabiaj żadnych zwilżonych lub wilgot-
nych powierzchni.
Urządzenie należy prowadzić zawsze w stanie
włączonym do przedmiotu obrabianego. Po
obróbce należy podnieść urządzenie z przed-
miotu obrabianego i dopiero wtedy je wyłączyć.
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
20 PL
Uruchomienie / Obsługa
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi / Uruchomienie
W trakcie obróbki zawsze trzymaj urządzenie
mocno oburącz (zobacz również rysunek E).
Zadbaj o pewną podstawę.
Pozwól, aby urządzenie całkowicie zatrzymało
się i wyłącz je zanim je odłożysz.
Podczas przerw w pracy, przed wszelkimi ro-
botami na urządzeniu (na przykład wymiana
papieru ściernego)oraz w przypadku nieużyt-
kowania urządzenia należy zawsze wyciągnąć
wtyk sieciowy z wtykowego gniazdka sieciowego
.
Q
Uruchomienie
Q
Zamocowanie / wymiana
taśmy szlifierskiej
NIEBEZPIECZEŃSTWO
POWSTANIA OBRAŻEŃ! Zawsze wyciągnij wtyk
sieciowy z wtykowego gniazdka sieciowego zanim
przystąpisz do wykonania robót na szlifierce taśmowej.
1. Najpierw należy poluzować zamocowanie
taśmy szlifierskiej odchylając całkowicie dźwi-
gnię
9
(patrz rys. A). Zamocowanie jest teraz
otwarte i można wyjąć taśmę szlifierską.
2. Teraz należy założyć nową taśmę szlifierską
względnie wymienić ją, aby obrabiać inny
materiał lub zmienić ziarnistość.
WAŻNE: Kierunki strzałek na stronie wewnętrz-
nej taśmy szlifierskiej oraz na obudowie urzą-
dzenia muszą być zgodne.
3. Naciśnij znowu dźwignię mocująca
9
w
pozycję wyjściową.
Ustawianie taśmy szlifierskiej:
Proszę podnieść urządzenie, włączyć je i obró-
cić. Następnie należy ustawić przebieg taśmy
obracając śrubę regulacyjną
6
tak, aby kra-
wędź taśmy przylegała do krawędzi urządze-
nia i była do niej równoległa (rys. B).
WAŻNE: Zwracaj bezwzględnie uwagę na to,
żeby taśma szlifierska nie ocierała się o obudo-
wę. Sprawdzaj regularnie bieg taśmy i w razie
potrzeby wyreguluj go za pomocą śruby justu-
jącej
6
.
Q
Wskazówki robocze
Niewielki nacisk przy szlifowaniu
wystarczy:
Pracuj przy niewielkim nacisku szlifowania. Ciężar
własny szlifierki taśmowej jest wystarczający
do uzyskania dobrych wydajności szlifowania.
Dzięki takiemu sposobowi pracy oszczędzasz
zużycie taśmy szlifierskiej, a powierzchnia ob-
rabianego przedmiotu będzie gładsza.
Usuwanie materiału i powierzchnia:
Wydajność usuwania materiału i jakość powierzch-
ni jest wyznaczana przez prędkość taśmy szlifierskiej
oraz grubość ziarna taśmy szlifierskiej (zobacz rów-
nież rozdział »Wybór obrotów i taśmy szlifierskiej«).
Proces szlifowania:
Włączone urządzenie ulokować na obrabianym
przedmiocie i pracować z równomiernym po-
suwem. Proces szlifowania należy prowadzić
wnoległymi pasmami i na zakładkę. Aby unik-
nąć zakłócających obraz szlifu, przebiegają
cych
poprzecznie śladów szlifowania, należy szlifo-
wać wyłącznie w kierunku włókien. Po obróbce
podnieś urządzenie z przedmiotu obrabianego
i dopiero wtedy je wyłącz.
Q
Odsysanie pyłu
ZAGROŻENIE POŻA-
ROWE! W trakcie robót z urządzeniami elektrycz-
nymi, które dysponują pojemnikami zintegrowanego
systemu odsysania pyłu lub które mogą zostać
połączone poprzez urządzenie odsysające pył z
odkurzaczem, istnieje zagrożenie pożarowe! Przy
niekorzystnych warunkach, takich jak na przykład
wyrzucanie iskier przy szlifowaniu metalu lub resztek
metalu w drewnie może nastąpić samozapłon pyłu
drzewnego w pojemniku zintegrowanego systemu
odsysania pyłu (lub w worku na pył odkurzacza).
Może to nastąpić w szczególności wtedy, gdy pył
drzewny jest wymieszany z resztkami lakieru lub
innymi substancjami chemicznymi, a zeszlifowany
materiał wskutek dłuższej pracy szlifierki jest gorący.
Dlatego też należy bezwzględnie unikać przegrza-
1 / 1

Parkside 104387 Operation and Safety Notes

Kategória
Elektrické náradie
Typ
Operation and Safety Notes
Táto príručka je tiež vhodná pre

V iných jazykoch