Panasonic VDRD310EP Návod na obsluhu

Operating Instructions

Instrukcja obsługi

Návod k použití

Kezelési utasítás

For PC Connection

Before use, please read these instructions completely.

Przed pierwszym włączeniem kamery prosimy o dokładne przeczytanie instrukcji obsługi.

Před použitím si, prosíme, přečtěte celý návod.

Használat előtt kérjük, hogy teljesen olvassa el ezt a kezelési utasítást.

LSQT1140 A

LSQT1140_EN.book 1 ページ２００６年１２月７日　木曜日　午後７時４５分

2

LSQT1140

End User License

Agreement

Before opening the CD-ROM package, please

read the following.

You (“Licensee”) are granted a license for the

Software defined in this End User Software

Agreement (“Agreement”) on condition that you

agree to the terms and conditions of this

Agreement. If Licensee does not agree to the

terms and conditions of this Agreement, promptly

return the Software to Matsushita Electric

Industrial Co., Ltd. (“Matsushita”), its distributors

or dealers from which you made the purchase.

Article 1 License

Licensee is granted the right to use the software,

including the information recorded or described

on the CD-ROM, instruction manuals, and any

other media provided to Licensee (collectively

“Software”), but all applicable rights to patents,

copyrights, trademarks and trade secrets in the

Software are not transferred to Licensee.

Article 2 Use by a Third Party

Licensee may not use, copy, modify, transfer or

allow any third party, whether free of charge or

not, to use, copy or modify the Software, except

as expressly provided for in this Agreement.

Article 3 Restrictions on Copying the Software

Licensee may make a single copy of the

Software in whole or in part solely for back-up

purposes.

Article 4 Computer

Licensee may only use the Software on a single

computer at a single location.

Article 5 Reverse Engineering, Decompiling or

Disassembly

Licensee may not reverse engineer, decompile,

or disassemble the Software, except to the

extent either of them is permitted under law or

regulation of the country where Licensee resides.

Matsushita, or its distributors or dealers will not

be responsible for any defects in the Software or

damage to Licensee caused by Licensee’s

reverse engineering, decompiling, or

disassembly of the Software.

Article 6 Limitation of Liability

The Software is provided “AS-IS” without

warranty of any kind, either expressed or implied,

including, but not limited to, warranties of non-

infringement, merchantability and/or fitness for a

particular purpose. Further, Matsushita does not

warrant that the operation of the Software will be

uninterrupted or error free. Matsushita or any of

its distributors or dealers will not be liable for any

damage suffered by Licensee arising from or in

connection with Licensee’s use of the Software.

Article 7 Export Control

Licensee agrees not to export or re-export to any

country the Software in any form without the

appropriate export licenses under regulations of

the country where Licensee resides, if

necessary.

Article 8 Termination of License

The right granted to Licensee hereunder will be

automatically terminated if Licensee violates any

of the terms and conditions of this Agreement.

Upon such automatic termination, Licensee must

destroy the Software and related documentation

together with all the copies thereof at Licensee’s

own expense.

LSQT1140_EN.book 2 ページ２００６年１２月７日　木曜日　午後７時４５分

3

LSQT1140

End User License Agreement ...............2

Before using

Before using with a computer...............4

What you can do with a computer..............4

Contents on provided CD-ROM .................5

Operating environment...............................7

Installation/Connection

Installation ............................................10

Installing DVD-RAM Driver.......................10

Installing DVD-MovieAlbumSE.................11

Installing DVDfunSTUDIO ........................12

Starting the applications ...........................13

Reading the operating instructions of the

software applications................................13

Software application uninstallation ...........14

Connection and recognition ...............14

Connection and recognition procedures...14

About the computer display......................15

To disconnect USB cable safely...............16

Verifying the unit is correctly recognized

by the computer........................................16

Creating a DVD-Video

Creating a DVD-Video disc on a

computer...............................................18

Creating a DVD-Video

on a computer from a DVD-RAM

or DVD-RW (VR format)...........................18

Others

Frequently asked questions................21

Troubleshooting...................................22

Contents

ENGLISH

LSQT1140_EN.book 3 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

4

LSQT1140

Before using

Before using with a computer

You can export motion pictures recorded on this unit to a computer with the software on the supplied

CD-ROM and create original DVD-Video discs.

∫ When using a DVD-RAM or DVD-RW (VR format) recorded on this unit

≥ Before using DVD-RW (VR format) on a computer, be sure to finalize it on this unit.

∫ When using a DVD-RW (Video format) or DVD-R recorded on this unit

≥ Before using the disc on a computer, be sure to finalize it on this unit.

∫ When using an SD card recorded on this unit

≥ Always use the AC adaptor when connecting the unit to the computer. You cannot connect to the

computer when using a battery.

≥ We cannot guarantee proper operation of this unit if you use software other than that supplied.

What you can do with a computer

Can do Software used

Playing back on a computer DVD-MovieAlbumSE (supplied)

Copying a disc VR disc copy tool (supplied)

Creating a DVD-Video disc

DVD-MovieAlbumSE (supplied) and

DVDfunSTUDIO (supplied)

Can do Software used

Playing back on a computer

Commercially available DVD-Video playback

software

Copying a disc DVDfunSTUDIO (supplied)

Can do Software used

Playing back on a computer

Standard Windows picture viewer or a

commercially available picture viewer

Copying files to a computer Windows Explorer

LSQT1140_EN.book 4 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

5

LSQT1140

The following software applications are contained on the provided CD-ROM.

∫ DVD-RAM Driver

This is necessary to configure the unit as a drive on a computer.

∫ DVD-MovieAlbum

DVD-MovieAlbumSE:

This software is for playing back VR format motion pictures.

By using DVD-MovieAlbumSE with this unit, it is possible to perform playback of the DVD-RAM or

DVD-RW (VR format). It is also possible to transfer exported data to DVDfunSTUDIO.

It is possible to edit the motion pictures on a DVD-RAM if you have a separate DVD-RAM drive.

Playing back DVD-RAM and DVD-RW (VR format).

A Playback area

B Thumbnails

Disc contents are shown.

VR disc copy tool:

This is used when creating a copy of a VR format disc.

Copy the data to the hard disk of the computer and then write it to another DVD-RAM.

≥ A separate DVD-RAM drive is required to create another DVD-RAM disc.

Contents on provided CD-ROM

A

B

LSQT1140_EN.book 5 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

6

LSQT1140

∫ DVDfunSTUDIO

This software is for creating a DVD-Video disc.

Use this software when burning a DVD-Video disc from motion pictures exported using

DVD-MovieAlbumSE. For details, refer to page 18.

≥ To create a DVD-Video disc, a separate DVD-RW/DVD-R/iRW/iR drive is required.

1 Export the images from a DVD-RAM or DVD-RW (VR format) with

DVD-MovieAlbumSE.

A File Export

2 Create a DVD menu with DVDfunSTUDIO, then write the data to a new

disc.

B DVD menus created

Arrange the motion pictures exported from DVD-MovieAlbumSE in the DVD menu and edit the

menu design.

C Burning button

The contents start being written to disc.

3 A DVD-Video disc is created.

Playback is possible on a DVD player.

∫ Acrobat Reader

To view the installed operating instructions, Adobe Acrobat Reader 5.0 or later is required.

If the Adobe Acrobat Reader is not already installed on your computer, you can install it from the CD-

ROM. Click the desired language in [Setup Menu], and follow the on-screen messages to install.

Creating a copy of a DVD-RW (Video format) or a DVD-R:

If you use the [Burn from an image] function in DVDfunSTUDIO, you can create a new disc from the

data copied to the computer with Windows Explorer.

Refer to the operating instructions of DVDfunSTUDIO for details.

≥ If your DVD player does not support DVD-R DL, playback is possible on it by copying the DVD-

R DL contents recorded on this unit to a DVD-RW or a DVD-R.

≥ To create a copied disc, a separate DVD-RW/DVD-R/iRW/iR drive is required.

A

B

C

LSQT1140_EN.book 6 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

7

LSQT1140

≥ A CD-ROM drive is necessary to install the supplied software applications.

≥ When 2 or more USB devices are connected to a computer, or when devices are connected through

USB hubs or by using extension cables, proper operation is not guaranteed.

≥ Use the supplied USB cable when connecting to the computer. (Operation is not guaranteed with any

other USB cables.)

∫ DVD-RAM Driver

≥ The driver operates as Read Only.

∫ DVD-MovieAlbumSE 4.3

≥ Even if the system requirements mentioned in these operating instructions are fulfilled, some

computers cannot be used.

≥ This software cannot be used on a Macintosh OS.

≥ DirectX 9.0c will be installed automatically during installation of the supplied software.

≥ Operation on an OS other than the one pre-installed is not guaranteed.

≥ Operation on Microsoft Windows XP Media Center Edition, Tablet PC Edition and 64-bit operating

system is not guaranteed.

≥ Depending upon the environment of your computer, if it does not support Hi-Speed USB (USB 2.0),

for example, frame dropout may occur, the audio may be intermittent, or the software may run slowly

when you play back recorded images. DVD-RAM and DVD-RW (VR format) can be used if you insert

them in the computer’s internal DVD-RAM/DVD-RW (VR format) compatible drive.

Operating environment

Personal computer IBM PC/AT compatible personal computer

OS Microsoft Windows 2000 Professional

Microsoft Windows XP Home Edition

Microsoft Windows XP Professional

CPU Intel Pentium III 450 MHz or higher

Personal computer IBM PC/AT compatible personal computer

OS Microsoft Windows 2000 Professional

Microsoft Windows XP Home Edition

Microsoft Windows XP Professional

CPU Intel Pentium III 800 MHz or higher

(Intel Pentium 4 1.3 GHz or higher recommended)

RAM 256 MB or more (512 MB or more recommended)

Display Medium (16 bit)/High Colour (16 bit) or more

Desktop resolution of 800k600 pixels or more

(Graphics card complying with DirectX 9.0c, and DirectDraw over lay)

32 MB video memory or more

Free hard disk space 200 MB or more

Sound Windows compatible sound device (DirectSound Support)

Interface Hi-Speed USB (USB 2.0) — A type

Necessary software DirectX 9.0c

Acrobat Reader 5.0 or later

LSQT1140_EN.book 7 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

8

LSQT1140

∫ DVDfunSTUDIO 2.5

≥ To create a DVD-Video disc, a separate DVD-RW/DVD-R/iRW/iR drive is required.

≥ Even if the system requirements mentioned in these operating instructions are fulfilled, some

computers cannot be used.

≥ This software cannot be used on a Macintosh OS.

≥ DirectX 9.0c will be installed automatically during installation of the supplied software.

≥ Operation on an OS other than the one pre-installed is not guaranteed.

≥ Input is not supported in languages other than English, German, French, Italian, Spanish and

Simplified Chinese.

≥ Operation cannot be guaranteed on all DVD drives.

≥ DVD discs authored with this software are not guaranteed to play in all DVD players.

≥ Operation on Microsoft Windows XP Media Center Edition and Tablet PC Edition is not guaranteed.

≥ This software is not compatible with Microsoft Windows 3.1, Windows 95, Windows 98/98SE,

Windows Me, Windows NT and 64-bit operating system.

≥ If your computer does not satisfy the above system requirements, an error may occur when writing

data to disc.

≥ Set the display resolution to 1024k768 (16 bits colour) or higher.

Select [start] # ([Settings] #) [Control Panel] # ([Appearance and Themes] #) [Display] and select

[Settings] tab, and then adjust [Screen resolution] and [Color quality].

Personal computer IBM PC/AT compatible personal computer

OS Microsoft Windows 2000 Professional Service Pack 4

Microsoft Windows XP Home Edition Service Pack 2

Microsoft Windows XP Professional Service Pack 2

CPU Intel Pentium III 800 MHz or higher

(Intel Pentium 4 1.3 GHz or higher recommended)

RAM 256 MB or more (512 MB or more recommended)

Display Medium (16 bit)/High Colour (16 bit) or more

Desktop resolution of 1024k768 pixels or more

(Graphics card complying with DirectX 9.0c, and DirectDraw over lay)

32 MB video memory or more

Free hard disk space 200 MB or more

≥ When writing to a disc, the same amount of free space as the disc is

necessary.

Sound Windows compatible sound device (DirectSound Support)

Interface Hi-Speed USB (USB 2.0) — A type

Necessary software DirectX 9.0c

Acrobat Reader 5.0 or later

LSQT1140_EN.book 8 ページ２００６年１２月７日　木曜日　午後７時４５分

Before using

9

LSQT1140

∫ Using Built-in SD Drive

≥ The USB equipment operates with the driver installed as standard in the OS.

≥ Microsoft

®

, Windows

®

and DirectX

®

are either registered trademarks or trademarks of the Microsoft

Corporation in the United States and/or other countries.

≥ IBM and PC/AT are registered trademarks of International Business Machines Corporation of the

U.S.

≥ Intel

®

and Pentium

®

are the registered trademarks or trademarks of the Intel Corporation in the

United States and other countries

≥ Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

≥ Other names of systems and products mentioned in these instructions are usually the registered

trademarks or trademarks of the manufacturers who developed the system or product concerned.

Personal computer IBM PC/AT compatible personal computer

OS Microsoft Windows 2000 Professional

Microsoft Windows XP Home Edition

Microsoft Windows XP Professional

CPU Intel Pentium II 300 MHz or higher

RAM 32 MB or more (64 MB or more recommended)

Interface USB 1.1 or later — A type

LSQT1140_EN.book 9 ページ２００６年１２月７日　木曜日　午後７時４５分

10

LSQT1140

Installation/Connection

Installation

When installing the software, log on to your

computer as the Administrator or with a user

name with equivalent authorization. (If you do not

have authorization to do this, consult your

manager.)

≥ Before starting the installation, close any other

software applications which are running.

≥ Do not perform any other operations on your

computer while the software is being installed.

≥ If another DVD-RAM Driver is already installed

in your computer, check this DVD-RAM Driver.

If packet writing software which supports DVD-

RAM discs is installed, it is necessary to

uninstall it and then install the provided

DVD-RAM Driver.

≥ Install DVD-RAM Driver and then install

DVD-MovieAlbumSE or DVDfunSTUDIO.

1 Insert the CD-ROM into the

computer.

The introduction movie starts.

Click [To continue the installation] at the end of

the introduction movie and then the [Setup

Menu] screen will appear.

≥ If the introduction movie screen does not

appear, double-click the CD-ROM drive icon in

[My Computer].

2 Click [DVD-RAM Driver].

≥ The software application may not run properly

if you cancel the installation at any point e.g. by

pressing [Cancel].

3 Click

[Driver and Formatter Setup].

≥ If an [Information] or [Question] message

appears, continue following the on-screen

messages for installation.

4 Click [Next].

5 Read carefully through the End

User License Agreement (l 2),

then click [Yes].

≥ You cannot install the application if you click

[No].

Do not connect the USB cable before

installing the DVD-RAM Driver.

If the DVD-RAM Driver is installed after

connecting this unit and the computer with

the USB cable, this unit may not be

correctly recognized by the computer.

(The DVD-RAM Driver has a driver for USB

connection.)

Installing DVD-RAM Driver

LSQT1140_EN.book 10 ページ２００６年１２月７日　木曜日　午後７時４５分

11

LSQT1140

Installation/Connection

6 Click [Next].

Continue to follow the on-screen messages to

install it.

7 When installation is complete, some notes

will appear:

Check the contents, then click

[k] at the top right of window.

8 Click [Finish].

Windows 2000 only:

The detection of device will start, after which it

will take several minutes for the computer to

detect the device. When detecting the device is

complete, a message that prompts you to reboot

will appear:

Click [Yes].

∫ If any trouble has occurred while installing

DVD-RAM Driver:

When [Block] is selected in the [Driver Signing

Options] in the [System Properties], the

installation procedure will not complete. Select

[Warn] and try again.

To check and change the setting, select [start] #

([Settings] #) [Control Panel] # ([Performance

and Maintenance] #) [System] and select [Driver

Signing] of the [Hardware] tab.

∫ About the [RAMASST] support tool:

[RAMASST] is a support tool for Windows XP

that disables the drive’s CD writing function so

that data can be written from a computer to a

DVD-RAM.

When you install the DVD-RAM Driver,

[RAMASST] is automatically installed and

displayed in [Startup].

1 Insert the CD-ROM into the

computer.

The introduction movie starts.

Click [To continue the installation] at the end of

the introduction movie and then the [Setup

Menu] screen will appear.

≥ If the introduction movie screen does not

appear, double-click the CD-ROM drive icon in

[My Computer].

2 Click [DVD-MovieAlbumSE 4.3].

≥ The software application may not run properly

if you cancel the installation at any point e.g. by

pressing [Cancel].

≥ Depending on the operating environment, you

may be required to install DirectX 9.0c. If so,

click [Yes], and install it.

If you install the software in a computer that is

not compatible with DirectX 9.0c, the computer

may not work properly. If you are unsure

whether or not your computer is compatible,

contact the maker of your computer.

The computer must be rebooted for the driver

to work.

Installing

DVD-MovieAlbumSE

LSQT1140_EN.book 11 ページ２００６年１２月７日　木曜日　午後７時４５分

12

LSQT1140

Installation/Connection

3 Click [Next].

4 Select [PAL (Europe)] for the TV

system, click [Next].

Continue to follow the on-screen messages to

install it.

5 Click [Finish].

1 Insert the CD-ROM into the

computer.

The introduction movie starts.

Click [To continue the installation] at the end of

the introduction movie and then the [Setup

Menu] screen will appear.

≥ If the introduction movie screen does not

appear, double-click the CD-ROM drive icon in

[My Computer].

2 Click [DVDfunSTUDIO 2.5].

≥ The software application may not run properly

if you cancel the installation at any point e.g. by

pressing [Cancel].

≥ Depending on the operating environment, you

may be required to install DirectX 9.0c. If so,

click [Yes], and install it.

If you install the software in a computer that is

not compatible with DirectX 9.0c, the computer

may not work properly. If you are unsure

whether or not your computer is compatible,

contact the maker of your computer.

3 Click [Next].

4 Select [PAL (Europe)] for the TV

system, click [Next].

Continue to follow the on-screen messages to

install it.

The computer must be rebooted for the

application to work.

Installing DVDfunSTUDIO

LSQT1140_EN.book 12 ページ２００６年１２月７日　木曜日　午後７時４５分

13

LSQT1140

Installation/Connection

5 Click [Finish].

1 Select [start] #

[All Programs (Programs)] #

[Panasonic] # [DVD camcorders]

# [DVD camcorders].

A screen showing a brief explanation of the

application is displayed.

2 Click [Close].

3 Click the desired item to start it.

A DVD-MovieAlbum starts

B DVDfunSTUDIO starts

C Images recorded on this unit are copied to

the hard disk on the computer or another

DVD-RAM

D DVD-RAM can be initialized

E The DVD-MovieAlbum playback

environment can be set

F Displays a list of discs that can be used

G Plays the application introduction movie

For details on how to use the software

applications, read the PDF instructions.

≥ You will need Adobe Acrobat Reader 5.0 or

later to read the PDF operating instructions.

(l 6)

∫ DVD-RAM Driver

Select [start] # [All Programs (Programs)] #

[DVD-RAM] # [DVD-RAM Driver] #

[Using DVD-RAM disc].

∫ DVD-MovieAlbumSE

Select [start] # [All Programs (Programs)] #

[Panasonic] # [DVD-MovieAlbumSE] #

[Operation Manual].

The computer must be rebooted for the

application to work.

Starting the applications

Reading the operating

instructions of the software

applications

A

B

C

D

E

F G

LSQT1140_EN.book 13 ページ２００６年１２月７日　木曜日　午後７時４５分

14

LSQT1140

Installation/Connection

∫ DVDfunSTUDIO

Select [start] # [All Programs (Programs)] #

[Panasonic] # [DVDfunSTUDIO] #

[Operating instructions].

Follow the steps below to uninstall any software

applications that you no longer require.

1 Select [start] # ([Settings] #)

[Control Panel] #

[Add or Remove Programs

(Applications)].

2 Select the software application to

be deleted, then click [Change/

Remove] ([Change or Remove] or

[Add/Remove]).

≥ Proceed with the uninstallation by following the

on-screen instructions.

≥ After uninstalling the software, be sure to

reboot the computer.

Connection and

recognition

After the driver and software applications are

installed, the unit must be connected to the

computer and be correctly recognized by the

computer.

≥ Connect after installing the driver and software

applications.

≥ If the supplied CD-ROM is inserted in the

computer, remove it. (If the [Setup Menu] is

running, wait until it finishes, then remove the

CD-ROM.)

≥ If the recognition procedure is not

accomplished properly, operation will not be

possible after connecting the unit to the

computer.

≥ If the unit fails to operate normally, it may mean

that you have not conducted the installation or

recognition procedure properly.

≥ Be sure to finalize DVD-RW (VR format),

DVD-RW (Video format) and DVD-R on this

unit, before using them on the computer.

Un-finalized discs will not be recognized by

the computer.

¬Connect this unit to the AC adaptor.

1 Insert a disc or card with

recorded images in the unit, then

turn on the unit.

Software application

uninstallation

Connection and recognition

procedures

LSQT1140_EN.book 14 ページ２００６年１２月７日　木曜日　午後７時４５分

15

LSQT1140

Installation/Connection

2 Connect this unit and a

computer.

A USB cable (supplied)

≥ Insert the plugs as far as they will go. The unit

and computer will not operate properly if the

plugs are not inserted fully.

≥ Do not use any other USB cables except the

supplied one. (Operation is not guaranteed

with any other USB cables.)

The USB function selection screen will appear.

3 Select [PC CONNECT(DISC)] or

[PC CONNECT(CARD)] and press

the joystick.

This unit is automatically recognized by the

computer.

≥ When the unit is connected to a computer,

its power cannot be turned off.

In this case, disconnect the USB cable (l 16).

≥ If the unit is connected to a computer when the

USB function is set to [PC CONNECT(DISC)],

no image will appear on the LCD monitor or the

viewfinder.

≥ When this unit is connected to a computer, you

cannot use this unit’s DISC EJECT lever to

remove a disc. Use Windows Explorer to right-

click the drive icon for this unit and select

[Eject].

≥ When a computer is accessing a disc or card in

this unit, the ACCESS/PC lamp or card access

lamp lights. (When a card is being accessed,

appears on the LCD monitor.) Do not

disconnect the USB cable or AC adaptor while

the disc or card is being accessed as it may

damage the data.

≥ The disc and card cannot be accessed

simultaneously.

≥ It may be necessary to reboot the computer

after connecting this unit to it for the first time.

When the unit is connected to a computer, it is

recognized as an external drive.

≥ Depending on the operating environment of the

computer, the shape of the drive icon and the

drive name (Example: E:) will differ.

∫ When accessing the disc

Windows XP:

Optical disc drive is displayed in [My Computer].

Windows 2000:

[Removable Disk] and optical disc drive are

displayed in [My Computer].

≥ When a DVD-RAM or DVD-RW (VR format) is

inserted in this unit, it can be accessed from

the removable disk drive.

≥ When a DVD-RW (Video format) or DVD-R is

inserted in this unit, it can be accessed from

the optical disc drive.

Example folder structure of a DVD-RAM or

DVD-RW (VR format):

≥ DVD video recording format motion pictures

are stored in the [DVD_RTAV] folder.

A

About the computer display

DVD_RTAV

DVD_CAMERA*

LSQT1140_EN.book 15 ページ２００６年１２月７日　木曜日　午後７時４５分

16

LSQT1140

Installation/Connection

Example folder structure of a DVD-RW (Video

format) or DVD-R:

≥ DVD-Video format motion pictures are stored

in the [VIDEO_TS] folder.

* Depending on the maker of the disc and the

device used to format it, the name displayed

will differ.

∫ When accessing the card

[Removable Disk] is displayed in [My Computer].

Example folder structure of an SD card:

≥ JPEG format still pictures (IMGA0001.JPG

etc.) are stored in the [100CDPFP] folder.

These can be opened with picture software

that supports JPEG pictures.

≥ Up to 999 files can be recorded in the

[100CDPFP] or other such folder.

≥ The DPOF setting files are recorded in the

[MISC] folder.

≥ Do not use the computer to delete the SD

card’s folders. Otherwise, it may no longer be

possible for this unit to read the SD card.

≥ Always use this unit to format SD cards.

≥ When data not supported by this unit has been

recorded on a computer, it will not be

recognized by this unit.

1 Double click the icon in task

tray.

Hardware disconnect dialogue appears.

≥ Depending on your computer’s settings, this

icon may not be displayed.

2 Select [USB Mass Storage

Device] and click [Stop].

3 Verify [MATSHITA DVD-RAM

LMXK1987 USB Device] or

[MATSHITA DVD Cam USB

Device] is selected and click

[OK].

Click [Close], and you can safely disconnect the

cable.

≥ If you disconnect the USB cable while the

access lamp is on or while appears on the

LCD monitor, it may freeze the software or

damage the data. (Refer to the operating

instructions for DVD Video Camera.)

To verify the unit is correctly recognized by the

computer, select the unit’s mode, connect the

unit to the computer via the USB cable and then

follow the steps below.

≥ With some computers including those made by

NEC, the Device Manager may not be

displayed if a mode that places restrictions on

the functions has been established. Consult

the manufacturer or follow the steps in your

computer’s operating instructions to establish a

mode in which all the functions can be used,

then proceed with operation.

Do not move or change the name of the

folders and files recorded on this unit by

Windows Explorer etc.

VIDEO_TS

DVD_CAMERA*

DCIM

Removable Disk

100CDPFP

MISC

To disconnect USB cable

safely

Verifying the unit is

correctly recognized by the

computer

LSQT1140_EN.book 16 ページ２００６年１２月７日　木曜日　午後７時４５分

17

LSQT1140

Installation/Connection

1

Select

[start]

#

(

[Settings]

#

)

[Control Panel]

#

(

[Performance

and Maintenance]

#

) [System].

2 Click the [Hardware] tab, then

click [Device Manager].

3 Verify the following items are

displayed.

∫ If the driver has been recognized

properly

When using a disc:

Windows XP:

≥ [MATSHITA DVD-RAM LMXK1987 USB

Device] is displayed at [DVD/CD-ROM

drives].

≥ [USB Mass Storage Device] is displayed at

[Universal Serial Bus controllers].

Windows 2000 Professional:

≥ [MATSHITA DVD-RAM LMXK1987 USB

Device] is displayed at [DVD/CD-ROM

drives].

≥ [MATSHITA DVD-RAM LMXK1987 USB

Device] is displayed at [Disc drives].

≥ [USB Mass Storage Device] is displayed at

[Universal Serial Bus controllers].

When using a card:

[USB Mass Storage Device] is displayed at

[Universal Serial Bus controllers].

∫ If the driver has not been

recognized properly

[!] or [Unknown device] appears at [Universal

Serial Bus controllers] or [Other devices], etc.

(Where the display will appear depends on the

type of computer you are using.)

You can use the following method to enable it to

be recognized.

Method 1: Turn off the unit and your computer

once and try again.

Method 2: Eject the disc or SD card from the

unit and try again.

Method 3: Try connecting the unit to another

USB port on your computer.

LSQT1140_EN.book 17 ページ２００６年１２月７日　木曜日　午後７時４５分

18

LSQT1140

Creating a DVD-Video

Creating a DV D-Video

Creating a DVD-Video

disc on a computer

Using DVD-MovieAlbumSE and

DVDfunSTUDIO, you can create a DVD-Video

disc (DVD-RW/DVD-R disc) from the images

recorded on this unit.

≥ Before using DVD-RW (VR format) on a

computer, be sure to finalize it on this unit.

≥ When using DVD-MovieAlbumSE or

DVDfunSTUDIO, log on to your computer as

Administrator with a login name equally

authorized. If you log on with a login name

other than Administrator, you cannot use the

applications.

≥ When using DVD-MovieAlbumSE or

DVDfunSTUDIO, close any other software

applications.

≥ The End User License Agreement is displayed

when the software is first started so read

carefully through its terms and conditions, then

click [I agree.].

¬Connect this unit to the AC adaptor.

1 Insert a DVD-RAM or DVD-RW

(VR format) with recorded

images in the unit, then

turn on

the unit

.

2 Connect this unit and a

computer.

A USB cable (supplied)

≥ Insert the plugs as far as they will go. The unit

and computer will not operate properly if the

plugs are not inserted fully.

≥ Do not use any other USB cables except the

supplied one. (Operation is not guaranteed

with any other USB cables.)

The USB function selection screen will appear.

3 Select [PC CONNECT(DISC)] and

press the joystick.

4 Prepare a DVD-RW/DVD-R/rRW/

rR drive that can be written to.

5 (On the computer)

Select [start] #

[All Programs (Programs)] #

[Panasonic] # [DVD camcorders]

# [DVD camcorders], then click

[DVD-MovieAlbum].

≥ If the screen showing a brief explanation of the

application is displayed, close it.

Creating a DVD-Video on a

computer from a DVD-RAM

or DVD-RW (VR format)

A

LSQT1140_EN.book 18 ページ２００６年１２月７日　木曜日　午後７時４５分

19

LSQT1140

Creating a DVD-Video

DVD-MovieAlbumSE starts and the images

recorded on the disc are displayed.

6 Click [Export].

7 Set the export settings in the

[Export all titles] screen and click

[Start].

≥ It is recommended that you do not change the

settings displayed on the screen.

8 When export is complete, a

message will appear. Check the

small box for [Eject the disc

being used.], and then click

[Yes].

DVD-MovieAlbumSE automatically closes and

DVDfunSTUDIO automatically starts.

9

Insert a brand-new DVD-RW or

DVD-R disc into the disc drive.

≥iRW and iR discs can also be used if the

disc drive supports them.

10

When the [CollectTool] screen

appears, click [OK].

The exported scene will be automatically

registered on the DVDfunSTUDIO editing

screen.

11

Edit the DVD menu as required.

≥ Select the desired destination drive to write to if

necessary.

12

Click [Burning].

When starting DVD-MovieAlbumSE, the

[Mount Information] dialogue box may appear

or the recorded images may not be shown. If

this occurs, try the following procedure. If

there are multiple drives, a drive other than

this unit may be selected.

1) Click [Preference] on the dialogue box or

([Preference]) button at top right of

DVD-MovieAlbumSE screen, and then

click the [Device setting] tab.

2) Choose the drive where the disc is loaded

in the [Drive Select] column, and then

click [OK].

LSQT1140_EN.book 19 ページ２００６年１２月７日　木曜日　午後７時４５分

20

LSQT1140

Creating a DVD-Video

Writing to the disc starts.

When writing is complete, the disc is ejected

automatically.

≥ The DISC EJECT lever on this unit does not

work when the unit is connected to a computer.

Use the software’s eject button to eject the

disc. (When not using the software, use

Windows Explorer to right-click the drive icon

for this unit and select [Eject].)

≥ The names of playlists created on this unit

cannot be displayed on DVD-MovieAlbumSE.

≥ If you export an image recorded in 16:9 aspect

ratio with DVD-MovieAlbumSE, it is saved as a

4:3 aspect image that has been squeezed

horizontally.

If you then use the exported image with

DVDfunSTUDIO, it is displayed as a 16:9

aspect image.

≥ The DVD menu created with DVDfunSTUDIO

does not appear on this unit. Play back the disc

on a DVD player.

≥ You cannot add data to a disc written to with

DVDfunSTUDIO as the disc is finalized after

writing.

Take care that the temperature of the unit,

when connected to a computer, does not

rise excessively (reference for usage:

approx. 30 minutes at about 30 °C).

LSQT1140_EN.book 20 ページ２００６年１２月７日　木曜日　午後７時４５分

Stránka sa načítava...

Panasonic VDRD310EP Návod na obsluhu

Panasonic VDRD310EP Návod na obsluhu

v iných jazykoch

Súvisiace články

Ostatné dokumenty