Sonoff The Origin/Elite Smart Temperature and Humidity Monitoring Switch Používateľská príručka

The Origin/Elite

Smart Temperature and

Humidity Monitoring Switch

User Manual • Uživatelský manuál •

Užívateľský manuál • Használati utasítás •

Benutzerhandbuch

2

English

3 – 16

Čeština

17 – 30

Slovenčina

31 – 44

Magyar

45 – 58

Deutsch

59 – 72

3

Dear customer,

Thank you for purchasing our product. Please read the following instructions carefully

before first use and keep this user manual for future reference. Pay particular attention to

the safety instructions. If you have any questions or comments about the device, please

contact the customer line.

✉ www.alza.co.uk/kontakt

✆ +44 (0)203 514 4411

Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

4

Product Introduction

TH Origin

TH Elite

Button

Protective cover

Sensor interface

On/Off LED indicator (Red)

Wi-Fi LED indicator(Blue)

Auto mode LED

indicator (Green)

Mounting base

Button

LED screen

Protective cover

Sensor interface

On/Off LED indicator (Red)

Wi-Fi LED indicator(Blue)

Mounting base

Auto mode LED

indicator (Green)

Dry contact interface

5

The device weight is less than 1kg. The installation height of less than 2m is

recommended.

Button instructions

Actions

Results

Single-click

Device on/off

Double-click

Auto-mode enable/disable

Long press for 5s

Enter the Pairing mode

LED indicator status instruction

LED indicator status

Status instruction

Blue LED indicator ﬂashes (one long and

two short)

Pairing mode

Blue LED indicator keeps on

Device is online

Blue LED indicator quick flashes once

Fail to connect to router

Blue LED indicator quick flashes twice

Connected to router but fail to connect

Blue LED indicator quick flashes three

times

Firmware updating

Green LED indicator keeps on

Auto-models on

Features

TH Origin/Elite is a DIY smart switch with temperature and humidity monitoring, and

required to use with the temperature and humidity sensors correspondingly.

Temp &Humi

Monitoring

Temp&Humi

History Data

Graph

Automatic

Mode

Share Control

Inching Mode

Voice Control

Timer Schedule

LAN Control

Wet&Dry

Contact

(TH Elite)

Screen Display

(TH Elite)

6

Device Installation

1. Power off

Please install and maintain the device by a professional electrician. To avoid electric

shock hazard, do not operate any connection or contact the terminal connector while the

device is powered on!

2. Wiring instruction

Remove protective cover

Wiring method of dry contact

7

Press the white button on the top of the wire connecting hole to insert the wire

corresponding, then release.

Dry contact wire conductor size: 0.13-0.5mm2, wire stripping length: 9-10mm.

Make sure all wires are connected correctly.

3. Insert the sensor

Compatible SONOFF sensors: DS18B20, MSO1,THSO1,AM2301, Si7021.

Compatible sensor extension cables: RL560.

Some old version sensors need to be used with the accompanying adapter.

Device pairing

1. Download the eWeLink App

8

2. Power on

After powering on, the device will enter the Bluetooth Pairing Mode during the first use.

The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.

The device will exit the Bluetooth Pairing Mode if not paired within 3mins. If you want

to enter this mode, please long press button for about 55 until the Wi-Fi LED indicator

changes in a cycle of two short and one long flash and release.

3. Add device

Method 1: Bluetooth Pairing

9

Tap "+" and select "Bluetooth Pairing", then operate following the prompt on the App.

Method 2: Scan QR code

In the Pairing mode, tap “Scan QR code” to add the device by scanning the QR code

on its back.

Alexa voice control instructions

1. Download the Amazon Alexa App and sign up an account.

2. Add Amazon Echo Speaker on the Alexa App.

3. Account Linking (Link Alexa account on the eWeLink App)

10

4. After linking the accounts, you can discover devices to connect on the Alexa App

according the prompt.

Account linking method of Google Assistant, Xiaodu, Tmall Genie, Mate Xiaoai and etc

is similar., the guides on the App shall prevail.

11

Specifications

Model

THR316,THR320,THR316D,THR320D

Input

THR316,THR316D: 100-240V~50/60Hz 16A Max

THR320,THR320D: 100-240V~50/60H 20A Max

Output

THR316,THR316D: 100-240V ~ 50/60Hz 16A Max

THR320, THR320D: 110-240V ~ 50/60HZ 20A Max

Dry contact output

5—30V, 1A Max

Wi-Fi

IEEE 802.11 b/g/n 2.4GHz

LED screen size

TH R316D, TH R320D: 43X33mm

App supported systems

Android 8LiOS

Working temperature

-10°C~40°C

Working humidity

5%-95% RH, non-condensing

Shell material

PC V0

Dimension

THR316,THR32O: 98x54x27.5mm

THR316D,THR320D: 98X54X31mm

LAN control

A communication method to control the devices directly without going through the

Cloud, which requires your smartphone and device connect to the same WIFI.

Operation notifications, operation records, firmware upgrades, smart scenes, devices

sharing and devices delete are not supported when there is no external network

connection.

Control modes

Manual mode: Turn on/off the device through the App and device itself whenever you

want.

Auto mode: Turn on/off the device automatically through pre-setting the threshold of

temperature and humidity.

Auto mode setting: Set the threshold of temperature & humidity and effective time

period, you can set up 8 automatic control programs in different time periods

12

Auto mode enable/disable

Enable/disable the auto mode by double click the button on the device or enable/disable it

on the App directly.

Manual control and Auto mode can work at the same time. In the auto mode, you can

turn on/off the device manually. After a while, auto mode will resume execution if it

detects changes in temperature and humidity.

Factory Reset

Deleting the device on the eWeLink app indicates you restore it to factory setting.

Common Problems

Fail to pair Wi-Fi devices to eWeLink APP

1. Make sure the device is in pairing mode. After three minutes of unsuccessful

pairing, the device will automatically exit pairing mode.

2. Please turn on location services and allow location permission. Before choosing the

Wi-Fi network, location services should be turned on and location permission should

be allowed. Location information permission is used to obtain Wi-Fi list information.

If you click Disable, you will not be able to add devices.

3. Make sure your Wi-Fi network runs on the 2.4GHz band.

4. Make sure you entered a correct Wi-Fi SSID and password, no special character

contained. Wrong password is a very common reason for pairing failure.

5. The device shall get close to the router for a good transmission signal condition

while pairing.

Wi-Fi devices "Ofﬂine" issue, Please check the following problems by the Wi-Fi

LED

indicator status:

The LED indicator blinks once every 2s means you fail to connect to the router.

1. Maybe you entered the wrong Wi-Fi SSID and password.

2. Make sure that your Wi-Fi SSID and password don't contain special characters, for

example, the Hebrew, Arabic characters, our system can't recognize these characters

and then fail to connect to the Wi-Fi.

3. Maybe your router has a lower carrying capacity.

4. Maybe the Wi-Fi strength is weak. Your router is too far away from your device, or

there may be some obstacle between the router and device which blocks the signal

transmission.

5. Be sure that the MAC of the device is not on the blacklist of your MAC management.

13

The LED indicator flashes twice on repeated means you fail to connect to the

server.

1. Make sure the Internet connection is working. You can use your phone or PC to

connect to the Internet, and if it fails to access, please check the availability of the

Internet connection.

2. Maybe your router has a low carrying capacity. The number of devices connected

to the router exceeds its maximum value. Please confirm the maximum number of

devices that your router can carry. If it exceeds, please delete some devices or get

a lager router and try again.

3. Please contact your ISP and confirm our server address is not shielded: cn-

disp.coolkit.cc (China Mainland)

as-disp.coolkit.cc (in Asia except China)

eu-disp.coo|kit.cc (in EU)

us-disp.coo|kit.cc (in US)

If none of the above methods solved this problem, please submit your request via

Help & feedback on the eWeLink App.

14

Warranty Conditions

A new product purchased in the Alza.cz sales network is guaranteed for 2 years. If you

need repair or other services during the warranty period, contact the product seller

directly, you must provide the original proof of purchase with the date of purchase.

The following are considered to be a conflict with the warranty conditions, for

which the claimed claim may not be recognized:

 Using the product for any purpose other than that for which the product is intended or

failing to follow the instructions for maintenance, operation, and service of the product.

 Damage to the product by a natural disaster, the intervention of an unauthorized

person or mechanically through the fault of the buyer (e.g., during transport, cleaning

by inappropriate means, etc.).

 Natural wear and aging of consumables or components during use (such as batteries,

etc.).

 Exposure to adverse external influences, such as sunlight and other radiation or

electromagnetic fields, fluid intrusion, object intrusion, mains overvoltage, electrostatic

discharge voltage (including lightning), faulty supply or input voltage and inappropriate

polarity of this voltage, chemical processes such as used power supplies, etc.

 If anyone has made modifications, modifications, alterations to the design or

adaptation to change or extend the functions of the product compared to the

purchased design or use of non-original components.

15

EU Declaration of Conformity

Identification data of the manufacturer's / importer's authorized representative:

Importer: Alza.cz a.s.

Registered office: Jankovcova 1522/53, Holešovice, 170 00 Prague 7

CIN: 27082440

Subject of the declaration:

Title: Smart temperature and Humidity Monitoring Switch

Model / Type: TH Origin/Elite

The above product has been tested in accordance with the standard(s) used to

demonstrate compliance with the essential requirements laid down in the

Directive(s):

Directive No. 2014/53/EU

Directive No. 2011/65/EU as amended 2015/863/EU

Prague, 22.12. 2022

16

WEEE

This product must not be disposed of as normal household waste in accordance with the

EU Directive on Waste Electrical and Electronic Equipment (WEEE - 2012/19 / EU). Instead,

it shall be returned to the place of purchase or handed over to a public collection point for

the recyclable waste. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product. Contact your

local authority or the nearest collection point for further details. Improper disposal of this

type of waste may result in fines in accordance with national regulations.

17

Vážený zákazníku,

Děkujeme vám za zakoupení našeho produktu. Před prvním použitím si prosím pečlivě

přečtěte následující pokyny a uschovejte si tento návod k použití pro budoucí použití.

Zvláštní pozornost věnujte bezpečnostním pokynům. Pokud máte k přístroji jakékoli dotazy

nebo připomínky, obraťte se na zákaznickou linku.

✉ www.alza.cz/kontakt

✆ +420 225 340 111

Dovozce Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz

18

Představení produktu

TH Origin

TH Elite

Tlačítk

o

Ochranný kryt

Rozhraní

senzoru

Indikátor LED

zapnutí/vypnutí (červený)

Indikátor Wi-Fi LED (modrý)

Indikátor LED

automatického

režimu (zelený)

Montážní

základna

Tlačítk

o

LED

obrazovka

Ochranný kryt

Rozhraní

senzoru

Indikátor LED

zapnutí/vypnutí (červený)

Indikátor Wi-Fi LED (modrý)

Montážní

základna

Indikátor LED

automatického

režimu (zelený)

Rozhraní suchého

kontaktu

19

Hmotnost zařízení je menší než 1 kg. Doporučená výška instalace je menší než 2 m.

Pokyny k tlačítkům

Akce

Výsledky

Jedním kliknutím

Zapnutí/vypnutí zařízení

Dvakrát klikněte na adresu

Povolení/zakázání automatického režimu

Dlouhé stisknutí po dobu 5 s

Vstup do režimu párování

Pokyn k indikaci stavu LED

Stav indikátoru LED

Stavový pokyn

Modrý LED indikátor ﬂashes (jeden dlouhý

a jeden dlouhý)

dva krátké)

Režim párování

Modrý indikátor LED stále svítí

Zařízení je online

Modrý indikátor LED jednou rychle blikne

Nepodařilo se připojit ke směrovači

Modrý indikátor LED dvakrát rychle blikne

Připojení ke směrovači, ale nepodaří se

připojit

Modrý indikátor LED třikrát rychle blikne

Aktualizace firmwaru

Zelený indikátor LED stále svítí

Automatické modely na

Funkce

TH Origin/Elite je chytrý vypínač pro kutily s monitorováním teploty a vlhkosti.

je nutné používat s odpovídajícími čidly teploty a vlhkosti.

Temp & Humi

Monitorování

Temp&Humi

Graf

historických dat

Automatický

režim

Kontrola sdílení

Režim Inching

Hlasové

ovládání

Časový plán

Řízení sítě LAN

Mokrý a suchý

kontakt

(TH Elite)

Zobrazení na

obrazovce

(TH Elite)

20

Instalace zařízení

1. Vypnutí napájení

Instalaci a údržbu zařízení musí provádět odborný elektrikář. Abyste předešli nebezpečí

úrazu elektrickým proudem, neprovádějte žádné operace s připojením ani se nedotýkejte

svorkovnice, pokud je zařízení zapnuté!

2. Pokyny k zapojení

Odstraňte ochranný kryt

Způsob zapojení suchého kontaktu

Stránka sa načítava ...

Sonoff The Origin/Elite Smart Temperature and Humidity Monitoring Switch Používateľská príručka

Táto príručka je tiež vhodná pre

Sonoff The Origin/Elite Smart Temperature and Humidity Monitoring Switch Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty