LG DR-275 Návod na obsluhu

DVD RECORDER

OWNER’S MANUAL

MODEL: DR275

Before connecting, operating or adjusting this product,

please read this instruction booklet carefully and completely.

DR275P2_NAACLLB_ENG

2

This lightning flash with arrowhead symbol within

an equilateral triangle is intended to alert the user

to the presence of uninsulated dangerous voltage

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

WARNING: Do not install this equipment in a confined space

such as a book case or similar unit.

CAUTION:

Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to protect

it from over heating.

The openings should be never be blocked by placing the

product on a bed, sofa, rug or other similar surface.This

product should not be placed in a built-in installation such as

a bookcase or rack unless proper ventilation is provided or

the manufacturer's instruction have been adhered to.

CAUTION:

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCKS DEFEATED AVOID

EXPOSURE TO THE BEAM.

CAUTION:

This product employs a Laser System.

To ensure proper use of this product, please read this

owner’s manual carefully and retain it for future reference.

Should the unit require maintenance, contact an authorized

service center.

Performing controls, adjustments, or carrying out procedures

other than those specified herein may result in hazardous

radiation exposure.

To prevent direct exposure to laser beam, do not try to open

the enclosure. Visible laser radiation when open. DO NOT

STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water

(dripping or splashing) and no objects filled with liquids, such

as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a

dedicated circuit;

That is, a single outlet circuit which powers only that

appliance and has no additional outlets or branch circuits.

Check the specification page of this owner's manual to be

certain.

Do not overload wall outlets. Overloaded wall outlets, loose

or damaged wall outlets, extension cords, frayed power

cords, or damaged or cracked wire insulation are dangerous.

Any of these conditions could result in electric shock or fire.

Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it,

discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse,

such as being twisted, kinked, pinched, closed in a door, or

walked upon. Pay particular attention to plugs, wall outlets,

and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord

plug. When installing the product, ensure that the plug is

easily accessible.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is

attached to a product it means the product is

covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be

disposed of separately from the municipal

waste stream via designated collection facilities

appointed by the government or the local

authorities.

3. The correct disposal of your old appliance will

help prevent potential negative consequences

for the environment and human health.

4. For more detailed information about disposal of

your old appliance, please contact your city

office, waste disposal service or the shop

where you purchased the product.

This product is manufactured to comply with

the EEC DIRECTIVE 89/336/EEC, 93/68/EEC

and 2006/95/EC.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

.

3

Introduction

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

About the symbol display . . . . . . . . . . . . . . . .4

Symbol Used in this Manual . . . . . . . . . . . . . . . .4

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . .4

Recordable and Playable Discs . . . . . . . . . . . . .5

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . .6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Operation . . . . . . . . . . . . . . . . .8

Hookup and Settings . . . . . . . . . . . . . . . . . . . .9-22

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connecting to the antenna . . . . . . . . . . . . . . . . .9

Connections to Your TV . . . . . . . . . . . . . . . . . .10

Connecting to an Amplifier . . . . . . . . . . . . . . . .11

Accessory Audio/Video (A/V) Connections . .12-13

Auto Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Using the Home Menu . . . . . . . . . . . . . . . . . . .14

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . .15

General Operation . . . . . . . . . . . . . . . . . . . .15

General Settings . . . . . . . . . . . . . . . . . . . . .15-17

Auto Programming . . . . . . . . . . . . . . . . . . .15

Program Edit . . . . . . . . . . . . . . . . . . . . . . . .16

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . .16

TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . .16

Progressive Scan / AV2 Connection . . . . . . .17

Video Output Format / Power Save Mode . .17

Factory Set . . . . . . . . . . . . . . . . . . . . . . . . .17

Language Settings . . . . . . . . . . . . . . . . . . . . . .17

Display Menu . . . . . . . . . . . . . . . . . . . . . . .17

Disc Menu/Audio/Subtitle . . . . . . . . . . . . . . .17

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . .18

Dolby Digital / DTS / MPEG . . . . . . . . . . . .18

Sampling Frequency . . . . . . . . . . . . . . . . . .18

DRC (Dynamic Range Control) . . . . . . . . . .18

Lock (Parental Control) Settings . . . . . . . . . .18-19

Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Set Password / Area Code . . . . . . . . . . . . .19

Recording Settings . . . . . . . . . . . . . . . . . . . . . .19

Record Mode Set . . . . . . . . . . . . . . . . . . . .19

Auto Chapter . . . . . . . . . . . . . . . . . . . . . . . .19

Disc Settings . . . . . . . . . . . . . . . . . . . . . . . .20-21

Initialize / Finalize . . . . . . . . . . . . . . . . . . . .20

Disc Label / Disc Protect . . . . . . . . . . . . . . .21

PBC / DivX Registration Code . . . . . . . . . . .21

General Explanation of On-Screen Display . . . .22

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-29

General Playback Features . . . . . . . . . . . . .23-25

Playing a DivX Movie File . . . . . . . . . . . . . . . . .26

Playing an Audio CD or MP3/WMA file . . . . . . .27

Viewing a JPEG File . . . . . . . . . . . . . . . . . .28-29

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . .30-34

About DVD recording . . . . . . . . . . . . . . . . . .30-31

Basic Recording from a TV . . . . . . . . . . . . . . . .32

Instant Timer Recording . . . . . . . . . . . . . . . . . .32

Timer Recording . . . . . . . . . . . . . . . . . . . . . . . .33

Checking Timer Recording Details . . . . . . . . . .34

Recording from an External Input . . . . . . . . . . .34

Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35-41

Title List and Chapter List Menu Overview . . . .35

VR Mode: Original and Playlist Editing . . . . . . .36

Adding Chapter Markers . . . . . . . . . . . . . . . . .36

Changing The Title Thumbnails . . . . . . . . . . . .36

Making a New Playlist . . . . . . . . . . . . . . . . . . . .37

Adding Additional Title/Chapters to the Playlist .37

Deleting an Original or Playlist Title/Chapter . . .38

Deleting a Part . . . . . . . . . . . . . . . . . . . . . . . . .38

Naming a Title . . . . . . . . . . . . . . . . . . . . . . . . .39

Time Search . . . . . . . . . . . . . . . . . . . . . . . . . .39

Divide One Titles Into Two . . . . . . . . . . . . . . . .40

Combining Two Chapters Into One . . . . . . . . . .40

Moving a Playlist Chapter . . . . . . . . . . . . . . . . .41

Hide a Chapter/Title . . . . . . . . . . . . . . . . . . . . .41

Protect a Title . . . . . . . . . . . . . . . . . . . . . . . . . .41

Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-47

Additional Information . . . . . . . . . . . . . . . . . . . .42

Overwriting Recording . . . . . . . . . . . . . . . . .42

Viewing Title List menu displayed on other

DVD Recorders or Players . . . . . . . . . . . . .42

Playing Your Recordings on Other DVD

Players (Finalizing a Disc) . . . . . . . . . . . . . .42

Language Codes . . . . . . . . . . . . . . . . . . . . . . .43

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Controlling Your TV with the Supplied

Remote Control . . . . . . . . . . . . . . . . . . . . . . . .44

Troubleshooting . . . . . . . . . . . . . . . . . . . . . .45-46

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .47

4

Introduction

To ensure proper use of this product, please read this

owner’s manual carefully and retain for future

reference.

This manual provides information on the operation

and maintenance of your recorder. Should the unit

require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during

operation and indicates that the function explained in

this owner’s manual is not available on that specific

media.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols

are applicable only to the disc represented by the

symbol.

All DVD discs listed below.

DVD-RW with VR recording mode

DVD-RW with Video recording mode

DVD+RW disc

DVD-R disc

DVD+R disc

DVD-Video disc

Video CDs

Audio CDs

DivX files

MP3 files

WMA files

JPEG files

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the

disc by the edges so that fingerprints do not get on

the surface. Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose

the disc to direct sunlight or sources of heat and never

leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor

picture quality and sound distortion. Before playing,

clean the disc with a clean cloth. Wipe the disc from

the center out.

Do not use strong solvents such as alcohol, benzine,

thinner, commercially available cleaners, or anti-static

spray intended for older vinyl records.

JPEG

WMA

MP3

DivX

ACD

VCD

DVD

+R

-R

+RW

-RW

Video

-RW

VR

DVD ALL

Moisture Condensation

Never operate this product immediately after

moving it from a cold location to a warm location.

Leave it for two or three hours without operating it.

If you use this product in such a situation, it may

damage discs and internal parts.

5

Introduction

Recordable and Playable Discs

DVD-RW (Digital Video Disc - ReWritable):

 DVD-RW discs can be formatted for VR mode recording or Video mode recording.

 These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again

on the same Disc.

[VR mode]

 Recordings can be extensively edited

 Playable only on VR mode compatible players (after finalization)

[Video mode]

 Playable on regular DVD players (after finalization)

 Limited editing features

DVD-R (Digital Video Disc - Recordable)



These Discs can be recorded only once. After you finalize a DVD-R, you cannot record on it or edit it.

 DVD-R discs can be only formatted to Video mode.

 Playable on regular DVD players (after finalization)

 Limited editing features

DVD+RW (Digital Video Disc + ReWritable)

 These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again

on the same Disc.

 Playable on DVD+RW compatible players (automatically finalization)

 The edited contents are playable on DVD+RW compatible players only after finalization

 Recordings can be edited the title/chapter

DVD+R (Digital Video Disc + Recordable)

 These Discs can be recorded only once. After you finalize a DVD+R, you cannot record on it or edit

it any more.

 Playable on DVD+R compatible players (after finalization)

 Any edited contents are not be compatible on DVD+R compatible players. (Hide, chapter combine,

added chapter mark, etc.)

 Limited title/chapter editing features.

Recommended recordable DVD discs

DVD-R DVD+R DVD-RW DVD+RW

Mitsubishi (8x, 16x) Mitsubishi (8x, 16x) Mitsubishi (2x, 4x) Mitsubishi (2.4, 4x)

Verbatim (8x, 16x) Verbatim (8x, 16x) Victir (4x) Verbatim (4x)

--Maxell (4x) Philips (4x)

Note: If a DVD-RW/DVD+RW discs is recorded using a personal computer or other DVD recorder, you cannot

format the disc using this recorder. So if you want to use the disc on this recorder, you must format the disc

using the original recorder.

6

Playable Discs

DVD (8 cm / 12 cm disc)

Discs such as movies that can be purchased or rented

Video CD (VCD) (8 cm / 12 cm disc)

VIDEO CDs or CD-Rs/CD-RWs in VIDEO CD/Super VIDEO CD format

Audio CD (8 cm / 12 cm disc)

Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased

CD-R/CD-RW (8 cm / 12 cm disc)

CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or JPEG files.

Notes:

 Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some

CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

 Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.

 Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.

 Depending on the recording software & the finalization, some recorded discs (CD-R/RW or DVD±R/RW) may

not be playable.

 DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder

may not play if the disc is damaged or dirty, or if there is dirt or condensation on the Recorder’s lens.

 If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases

in which it may not play because of the settings of the application software used to create the disc. (Check

with the software publisher for more detailed information.)

 This recorder requires discs and recordings to meet certain technical standards in order to achieve optimal

playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types

of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-

existing conditions (see above) to ensure compatible playback.

 Customers should note that permission is required in order to download MP3 / WMA files and music from the

Internet. Our company has no right to grant such permission. Permission should always be sought from the

copyright owner.

Regional Code

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as

the rear of the unit or “ALL”.

Notes on Regional Codes



Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must

match your unit’s regional code or the disc cannot play.



If you try to play a DVD with a different regional code from the unit, the message “Incorrect region code. Can’t

play back” appears on the TV screen.

7

Introduction

a

11

/ I (POWER button)

Switches the recorder ON or OFF.

b Disc Tray

Insert a disc here.

c Display window

Shows the current status of the recorder.

REC: The recorder is recording.

TV: Indicates when the recorder is in TV tuner

mode.

: Indicates when the recorder is in timer

recording or a timer recording is programmed.

: Shows the current status of the recorder

(clock, program number, etc).

d Remote Sensor

Point the recorder remote control here.

e AV IN 3 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external

source (Audio system, TV/ Monitor, VCR,

Camcorder, etc.).

f Z (OPEN/CLOSE)

Opens or closes the disc tray.

g N (PLAY)

Starts playback.

h z (REC)

Starts recording. Press repeatedly to set the

recording time.

Front Panel

abcdefgh

8

    

a

    

POWER: Switches the recorder

ON or OFF.

OPEN/CLOSE (Z): Opens and

closes the disc tray.

AV/INPUT: Changes the input to

use for recording (Tuner, AV1-3).

0-9 numerical buttons: Selects

numbered options in a menu.

TV Control Buttons: See page

44.

    

b

    

SCAN (m / M): Search

backward or forward.

SKIP (. / >): Go to next or

previous chapter or track.

PAUSE/STEP (X) : Pause

playback or recording temporarily.

PLAY (N): Starts playback.

STOP (x): Stops playback or

recording.

    

c

    

HOME: Accesses or removes the

HOME menu.

MENU/LIST: Accesses menu on a

DVD disc. Switches between Title

List-Original and Title List-Playlist

menu.

b / B / v / V (left/right/up/down):

Selects an option in the menu.

ENTER ( ): Acknowledges menu

selection.

PR/CH (+/-): Scans up or down

through memorized channels.

DISPLAY: Accesses On-Screen

Display.

RETURN (O): Removes the

menu.

AUDIO ( ): Selects an audio

language or audio channel.

SUBTITLE ( ): Selects a subtitle

language.

ZOOM: Enlarges video image.

SETUP: Accesses or removes the

Setup menu.

    

d

    

REC (z): Starts recording.

REC MODE: Selects the recording

mode.

THUMBNAIL: Selects a thumbnail

picture.

CHP. ADD: Inserts a chapter

marker when playing/recording.

PLAY MODE: Selects a play

mode.

CLEAR: Removes a mark on the

Marker Search menu.

TITLE: Displays the disc’s Title

menu, if available.

TV/DVD: To view channels

selected by the recorder tuner or

by the TV tuner.

Remote Control

a

b

c

d

Remote Control Operation

Point the Remote Control at the remote sensor and

press the buttons.

Caution

Do not mix old and new batteries. Never mix different

types of batteries (standard, alkaline, etc.).

Remote Control Battery Installation

Remove the battery cover on the rear of

the Remote Control, and insert two R03

(size AAA) batteries with and

matched correctly.

9

Hookup and

Settings

Connecting to the antenna

Remove the antenna cable plug from your TV set and

insert it into the antenna socket at the back of the

recorder. Plug one end of the antenna cable into the

TV socket on the recorder and the other end into the

antenna input socket on your TV set.

RF coaxial connection

Connect the ANTENNA OUT jack on the recorder to

the antenna input jack on the TV using the 75-ohm

Coaxial Cable supplied (R). The ANTENNA OUT jack

passes the signal through from the ANTENNA IN jack.

ANTENNA

INPUT

Aerial

Rear of the recorder

Rear of TV

L

R

AUDIO INPUT

VIDEO

INPUT

SCART INPUT

R

a ANTENNA IN

Connect the antenna to this terminal.

b COMPONENT OUTPUT (Y P

B PR)

Connect to a TV with Y P

B PR inputs.

c AV 2 (DECODER)

Connect the audio/video output of an external

source (Pay-TV decoder, Set Top Box, VCR, etc.).

d AC Power Cord

Plug into the power source.

e ANTENNA OUT

Passes the signal from the ANTENNA IN jack to

your TV/monitor.

f COAXIAL (Digital audio output)

Connect to digital (coaxial) audio equipment.

g AUDIO OUTPUT (Left/Right)

Connect to a TV with audio inputs.

h AV 1 (AUDIO/VIDEO)

Connect to a TV with SCART jack.

Rear Panel

Hookup and Settings

abc d

efgh

10

Connections to Your TV



Make one of the following connections, depending

on the capabilities of your existing equipment.



When using the COMPONENT OUTPUT jacks, set

the Video Output Format option in the setup menu

to YP

BPR. When using the SCART jack, set the

Video Output Format option in the setup menu to

RGB.

Tips



Depending on your TV and other equipment you

wish to connect, there are various ways you could

connect the recorder. Use only one of the

connections described below.



Please refer to the manuals of your TV, VCR,

Stereo System or other devices as necessary to

make the best connections.

Caution

– Make sure the recorder is connected directly to the

TV. Tune the TV to the correct video input channel.

– Do not connect the recorder’s AUDIO OUTPUT jack

to the phono in jack (record deck) of your audio

system.

– Do not connect your recorder via your VCR. The

DVD image could be distorted by the copy

protection system.

SCART connection

Connect the AV1 scart jack on the recorder to the

corresponding in jacks on the TV using the scart cable

(T).

Audio (Left/Right) Connection

Connect the left and right AUDIO OUTPUT jacks of

the recorder to the audio left and right IN jacks on the

TV using the audio cables (A). Do not connect the

recorder’s AUDIO OUTPUT jack to the phono in jack

(record deck) of your audio system.

Component Video connection

Connect the COMPONENT OUTPUT jacks on the

recorder to the corresponding input jacks on the TV

using an Y PB PR cable (C).

If your television is a high-definition or “digital ready”

television, you may take advantage of the recorder’s

progressive scan output for the highest video

resolution possible. If your TV does not accept the

Progressive Scan format, the picture will appear

scrambled if you try Progressive Scan on the recorder.



Set the Progressive Scan to [ON] on the setup

menu for progressive signal, see page 17.

Caution

Once the setting for Progressive Scan output is

entered, an image will only be visible on a

Progressive Scan compatible TV or monitor. If you set

Progressive Scan to [ON] in error, you must reset the

recorder. First, remove the disc in the recorder. Next,

press STOP (x) and hold it for five seconds before

releasing it. The video output will be restored to the

standard setting, and a picture will once again be

visible on a conventional analog TV or monitor.

Rear of the recorder

L

R

AUDIO INPUT

SCART INPUT

Pr

Pb

Y

COMPONENT VIDEO INPUT

Rear of TV

A

C

T

11

Hookup and

Settings

Connecting to an Amplifier

Connecting to an amplifier equipped with two

channel analog stereo or Dolby Pro Logic ll/

Pro Logic

Connect the Left and Right AUDIO OUTPUT jacks on

the recorder to the audio left and right in jacks on your

amplifier, receiver, or stereo system, using the audio

cables (A).

Connecting to an amplifier equipped with two

channel digital stereo (PCM) or to an Audio/

Video receiver equipped with a multi-channel

decoder (Dolby Digital™, MPEG 2, or DTS)

1. Connect one of the recorder’s DIGITAL AUDIO

OUTPUT jacks (COAXIAL X) to the corresponding

in jack on your amplifier. Use an optional digital

(coaxial X) audio cable.

2. You will need to activate the recorder’s digital

output. (See “Audio Settings” on page 18).

Digital Multi-channel sound

A digital multi-channel connection provides the best

sound quality. For this you need a multi-channel

Audio/Video receiver that supports one or more of the

audio formats supported by your recorder (MPEG 2,

Dolby Digital and DTS). Check the receiver manual

and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital

output will be in DTS digital out when DTS audio

stream is selected.

Notes:

–

If the audio format of the digital output does not match

the capabilities of your receiver, the receiver will

produce a strong, distorted sound or no sound at all.

– Six Channel Digital Surround Sound via digital

connection can only be obtained if your receiver is

equipped with a Digital Multi-channel decoder.

–To see the audio format of the current DVD in the

on-screen display, press AUDIO.

– This recorder does not perform internal (2 channel)

decoding of a DTS sound track. To enjoy DTS

multi channel surround, you must connect this

recorder to a DTS compatible receiver via one of

this recorder’s digital audio outputs.

R

L

AUDIO INPUT

Amplifier (Receiver)

Rear of the recorder

A

DIGITAL INPUT

COAXIAL

X

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the double-

D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of

Digital Theater Systems, Inc.

12

Accessory Audio/Video (A/V)

Connections

Connecting a PAY-TV/Canal Plus Decoder

You can watch or record PAY-TV/Canal Plus

programmes if you connect a decoder (not supplied)

to the recorder. Disconnect the recorder’s mains lead

from the mains when connecting the decoder.

To watch or record PAY-TV/Canal Plus programmes,

set [AV2 Connection] option to [Decoder] (see page

17) and set the program’s [Decoder On/Off] option to

[On] on the Setup menu (page 16).

Tip:

You do not need to turn on the recorder to view the

signals from the connected tuner on your TV.

Note:

If you disconnect the recorder’s mains lead, you will

not be able to view the signals from the connected

decoder.

Connecting to the AV2 DECODER jack

Connect a VCR or similar recording device to the AV2

DECODER jack of this recorder.

To watch or record the source from AV2 DECODER

jack, set [AV2 Connection] option to [Other Device]

(see page 17).

Tip:

You do not need to turn on the recorder to view the

signals from the connected tuner on your TV.

Notes:

 Pictures containing copy protection signals that

prohibit any copying cannot be recorded.

 If you pass the recorder signals via the VCR, you

may not receive a clear image on your TV screen.

Be sure to connect your VCR to the recorder and

your TV in the order shown below. To watch video

tapes, watch the tapes through a second line input

on your TV.

 When you record to a VCR from this recorder, do

not switch the input source to TV by pressing the

TV/DVD button on the remote.

 If you are using a B Sky B tuner, be sure to connect

the tuner’s VCR SCART jack to the AV2 DECODER

jack.

 If you disconnect the recorder’s mains lead, you will

not be able to view the signals from the connected

VCR or tuner.

TV

VCR RECORDER

Line input 1

Line input 2

TV

SCART AV

TV

13

Hookup and

Settings

Connecting to the AV IN 3 Jacks

Connect the input jacks (AV IN 3) on the recorder to

the audio/video out jacks on your accessory

component, using audio/video cables.

L

R

VIDEO

OUTPUT

AUDIO

OUTPUT

Jack panel of Accessory Component

(VCR, Camcorder, etc.)

Front of

the recorder

14

Auto Set Up

After the POWER is pressed for the first time to turn

on the unit or resetting the unit, the Initial Setup

Wizard function sets the language, clock and tuner

channels automatically.

1. Select a language for the Setup menu and on-

screen display. Use v / V to select a language

then press ENTER.

2. Please check your antenna connections.

Press ENTER to move next step.

3. Use v / V / b / B to select an audio system then

press ENTER while [Start] option is selected.

The tuner will automatically cycle through all

available channels in the area and place them in

the tuner’s memory.

4. Enter the necessary information for date and time.



b / B (left/right): Moves the cursor to the

previous or next column.



v / V (up/down): Changes the setting at the

current cursor position.

Press ENTER to confirm your setting.

5. Press ENTER while [Close] is highlighted to finish

setup.

Using the Home Menu

From the Home Menu screen you can access all the

Media for playback and recording of the recorder.

1. Press HOME to display the Home Menu screen.

The unit will be in TV viewing mode always when

the Home menu appears.

2. Use b / B buttons to select a main option you

want. Sub options appears.

3. Use v / V and ENTER buttons to select the sub

option you want.

4. To exit the HOME menu, press HOME.

Setup



Start: Displays Setup menu.

TV



Auto Ch. Scan: See page 15.



PR Edit: See page 16.



Timer Record: See page 33.

Movie



DISC:

- Displays Title List menu for recordable disc (page

35)

- Displays Movie List menu for DivX disc. (page 26)

-Plays back Video CD or DVD-Video disc (page

23-25).

Photo (See page 28-29)



DISC: Displays Photo List menu for disc.

Music (See page 27)



DISC: Displays Music List menu for disc.

Easy Menu



Disc Manager: Displays the Disc Settings menu.

(See page 20-21)



Rec. Mode: Displays the menu to select the record

mode. (See page 19)

15

Hookup and

Settings

Initial Settings

In this menu system, there are several ways to

customize the settings provided. Most menus consist

of three levels to set up the options, but some require

greater depth for the variety of settings.

General Operation

1. Press HOME and select [Setup] option.

2. Select [Start] option then press ENTER.

The Setup menu appears.

3. Use v / V to select the desired option.

4. While the desired item is selected, press B to

move to the second level.

5. Use v / V to select the second desired option.

6. Press B to move to the third level.

7. Use v / V to select the desired setting then press

ENTER to confirm your selection.

Some items require additional steps.

8. Press RETURN (O) repeatedly to exit the Setup

menu.

Note:

Press b to go back to the previous level.

General Settings

Auto Programming

This recorder is equipped with a frequency

synthesized tuner capable of receiving up to 88 TV

channels.

Preparation:

 Connect the recorder to the desired type of

antenna, as shown in Connecting to the antenna on

page 9.

1. Select the [Auto Programming] option.

2. Press B to move to the third level.

3. Use v / V to select the audio system then press

B. The [Start] icon is highlighted.

4. Press ENTER to begin the channel search.

The tuner will automatically cycle through all

available channels in the area and place them in

the tuner’s memory.

Note:

You can change the audio system of each program

with the Program Edit option in the setup menu when

the Auto Programming with the selected audio system

is completed (See “Program Edit”, page 16.).

16

Program Edit

You can edit a channel manually (add, delete, name,

move, etc.).

1. Select [Program Edit] option then press B.

2. Press ENTER while [Edit] is selected.

The Program List menu appears.

3. Use v / V to select a PR number then press

ENTER.

4. Use v / V to select the program option then press

ENTER.

 [Program Edit] Sets the channel manually. See

“Program Edit” on the bottom.

 [Station Rename] Changes the station name.

The display for entering characters appears.

To enter characters, see page 39.

Names can be up to 5 characters long.

 [Move] Sorts the programme positions on the

Program List. Press v / V to move the selected

programme position to a new location.

 [Delete] Disables a programme position you do

not need.

 [Decoder On/Off] Sets the channels for the

decoder. You need this setting to watch or

record PAY-TV/Canal Plus programmes.

Press ENTER so [Decoder] appears on the

display. Press ENTER again to turn off the

setting.

5. Press RETURN (O) repeatedly to exit Program

List menu.

Program Edit

You can perform a search to select and store TV

channels manually.

When you select [Program Edit] in step 4 above, the

display for setting channels appears.

1. Use b / B to select the item and press v / V to

change the setting.

 [PR] indicates the selected programme position.

 [Seek] Searches for a channel automatically.

Searching stops when the recorder tunes in a

channel.

 [Ch.] Changes the channel number.

 [MFT] Fine tunes the channel to obtain a clearer

picture.

 [Audio] Changes the audio system (BG, I or

DK).

2. Choose OK then press ENTER to confirm the

setting and returns to the Program List menu.

AV1 Decoder

Sets the AV1 AUDIO/VIDEO jack for inputting

encoded video signals.

1. Press AV/INPUT while the [Decoder On/Off] option

is highlighted.

2. Press ENTER so [Decoder] appears on the

display. Press ENTER again to turn off the setting.

 Off: Inputs the signals from the AV1 scart jack.

Normally select this.

 On: The encoded video signal input from the

AV1 scart jack is output to the AV2 DECODER

jack for decoding.

The decoded signal is then input back through

the AV2 DECODER jack so you can record or

view PAY-TV/Canal Plus programmes.

Clock Set

1. Select [Clock set] option then press B.

2. Enter the necessary information for date and time.

b / B (left/right): Moves the cursor to the previous

or next column.

v / V (up/down): Changes the setting at the

current cursor position.

3. Press ENTER to confirm your setting.

TV Aspect

Selects the aspect ratio of the connected TV (4:3

standard or wide).

 [4:3 Letter Box] Select this when connecting to a 4:3

screen TV. Displays a wide picture with bands on

the upper and lower portions of the screen.

 [4:3 Pan Scan] Select this when connecting to a 4:3

screen TV. Automatically displays a wide picture on

the entire screen and cuts off the portions that do

not fit.

 [16:9 Wide] Select this when connecting to a

wide-screen TV or TV with a wide mode function.

17

Hookup and

Settings

General Settings (Continued)

Progressive Scan

Progressive Scan Video provides the highest quality

pictures with less flickering.

If you are using the COMPONENT OUTPUT jacks,

but are connecting the recorder to a standard (analog)

television, set Progressive Scan to [OFF].

If you are using the COMPONENT OUTPUT jacks for

connection to a TV or monitor that is compatible with

a progressive scan signal, set Progressive Scan to

[ON].

Note:

Progressive Scan will be disable in the setup menu

when the Video Output Format in the setup menu is

set to RGB.

Caution

Once the setting for Progressive Scan output is

entered, an image will only be visible on a

Progressive Scan compatible TV or monitor. If you set

Progressive Scan to [ON] in error, you must reset the

recorder. First, remove the disc in the recorder. Next,

press STOP (x) and hold it for five seconds before

releasing it. The video output will be restored to the

standard setting, and a picture will once again be

visible on a conventional analog TV or monitor.

AV2 Connection

You can connect a decoder or other device to the

AV2 DECODER socket on the back.

 [Decoder] Select [Decoder] if you connect the

recorder’s AV2 DECODER jack to a PAY-TV or

Canal Plus decoder.

 [Other Device] Select [Other Device] if you connect

the recorder’s AV2 DECODER jack to a VCR or

similar recording device.

Video Output Format

Select the Video output format option according to the

connection type of this unit

 [YPbPr] When your TV is connected with the

COMPONENT OUTPUT jack on this unit.

 [RGB] When your TV is connected with the

SCART(RGB signal) jack on this unit.

Power Save Mode

You can set up the unit into an economic power save

mode. Nothing is displayed in the display window

when the unit is turned off.

 [OFF] Power Save Mode is not active.

 [ON] Power Save Mode is active.

Notes:

 The encoded television signals (CANAL+ or

PREMIERE) are not decoded in the Power Save

Mode.

 The Power Save Mode is not available in the

standby mode for the timer recording and when

power off of the unit after receiving the encoded

television signals (CANAL+ or PREMIERE).

Factory Set

If you need to, you can reset the Recorder to all its

factory settings. Select ‘‘ENTER’’ icon then press

ENTER and auto setup menu will appear, see page 14.

Note:

Some options can not be reset. (Rating, Password,

and Area Code)

Language Settings

Display Menu

Select a language for the Setup menu and on-screen

display.

Disc Menu/Audio/Subtitle

 [Original] Refers to the original language in which

the disc was recorded.

 [Others] To select another language, press number

buttons then ENTER to enter the corresponding

4-digit number according to the language code list

in the reference chapter (see page 43). If you make

a mistake while entering number, press CLEAR

repeatedly to delete numbers one by one then

correct it.

 [OFF] (for Disc Subtitle) : Turn off Subtitle.

18

Audio Settings

Each DVD disc has a variety of audio output options.

Set the recorder’s Audio Output according to the type

of audio system you use.

Dolby Digital / DTS / MPEG

 [Bitstream]: Select “Bitstream” if you connect the

recorder’s DIGITAL AUDIO OUT jack to an amplifier

or other equipment with a Dolby Digital, DTS or

MPEG decoder.

 [PCM] (for Dolby Digital / MPEG): Select when

connected to a two-channel digital stereo amplifier.

DVDs encoded in Dolby Digital or MPEG will be

automatically downmixed to two-channel PCM

audio.

 [Off] (for DTS): If you select “Off”, the DTS signal is

not output through the DIGITAL AUDIO OUT jack.

Sampling Frequency

If your receiver or amplifier is NOT capable of

handling 96 kHz signals, select [48 kHz]. When this

choice is made, this unit will automatically convert any

96 kHz signals to 48 kHz so your system can decode

them.

If your receiver or amplifier is capable of handling

96 kHz signals, select [96 kHz]. When this choice is

made, this unit will pass each type of signal through

without any further processing.

DRC (Dynamic Range Control)

With the DVD format, you can hear a program’s

soundtrack in the most accurate and realistic

presentation possible, thanks to digital audio

technology. However, you may wish to compress the

dynamic range of the audio output (the difference

between the loudest sounds and the quietest ones).

Then, you may listen to a movie at a lower volume

without losing clarity of sound. Set DRC to [ON] for

this effect.

Lock (Parental Control) Settings

Rating

Blocks playback of rated DVDs based on their

content. Not all discs are rated.

1. Select [Rating] option then press B.

2. To access the Rating, Password and Area Code

features, you must input the 4-digit security code

you created.

If you have not yet entered a security code you

are prompted to do so. Input a 4-digit code. Enter

it again to verify. If you make a mistake while

entering number, press CLEAR repeatedly to

delete numbers one by one then correct it.

3. Select a rating using the v / V buttons.

[1] - [8]: Rating one (1) has the most restrictions

and rating eight (8) is the least restrictive.

[No Limit]: If you select [No Limit], parental control

is not active and the disc plays in full.

4. Press ENTER to confirm your rating selection.

Note:

If you set a rating for the recorder, all disc scenes with

the same rating or lower are played. Higher rated

scenes are not played unless an alternate scene is

available on the disc. The alternative must have the

same rating or a lower one. If no suitable alternative is

found, playback stops. You must enter the 4-digit

password or change the rating level in order to play

the disc.

19

Hookup and

Settings

Lock (Parental Control) Settings

(Continues)

Set Password

1. Select [Set Password] option then press B.

2. Follow step 2 as shown “Rating” on page 18.

To change the password, select the [Change],

press ENTER and input the new password twice

after inputing the current password.

To delete the password, select [Delete] then input

the password.

If you forget your 4-digit code

If you forget your password, to clear the current

password, follow the procedure below.

1. Display Setup menu then select an 1 level icon.

2. Use the Number buttons to enter the 6-digit

number “210499”.

3. Select [OK] then press ENTER. The 4-digit

password is cleared. Enter a new code.

Area Code

Enter the code of an area whose standards were used

to rate the DVD video disc, referring to the list (See

“Area Codes”, page 43.).

1. Select [Area Code] option then press B.

2. Follow step 2 as shown “Rating” on page 18.

3. Select the first character using the v / V

buttons.

4. Shift the cursor using B buttons and select the

second character using v / V buttons.

5. Press ENTER to confirm your area code selection.

Recording Settings

Record Mode Set

You can set the picture quality for recording;

XP (High Quality), SP (Standard Quality),

LP (Low Quality), EP (Extend Quality),

MLP (Maximum Long Play).

Auto Chapter

When recording in Video mode, chapter markers are

put in specified setting. You can change this interval to

5 minutes or 10 minutes. If you select [None], switch

off automatic chapter marking altogether with the

[None] setting.

20

Disc Settings

Initialize

If you load a completely blank disc, the recorder will

initialize the disc.

DVD-R: The recorder initialize the disc to Video mode.

The recording mode will always be Video mode.

DVD-RW/DVD+RW/DVD+R: The Initialize menu will

appears. Select [OK] then press ENTER. DVD-RW

disc is initialized to Video mode.

Also, you can reformat the DVD-RW/DVD+RW from

the Setup menu as below.

1. Select [Initialize] option then press B.

2. Press ENTER while [Start] is selected.

Format Disc menu appears.

3. Use b / B to select a desired mode (VR Mode or

Video Mode) then press ENTER.

Confirm message will appear.

For DVD+RWs, go to step 4.

4. Use b / B to select [OK] then press ENTER.

It takes a few moments to initialize the disc.

Caution

If you want to change the disc format, everything

recorded on the disc will be erased.

Finalize

Finalizing ‘fixes’ the recordings in place so that the

disc can be played on a regular DVD player or

computer equipped with a suitable DVD-ROM drive.

Finalizing a Video mode disc creates a menu screen

for navigating the disc. This is accessed by pressing

MENU/LIST or TITLE.

Caution

Once you have finalized a DVD-R and DVD+R disc,

you cannot edit or record anything else on that disc

except DVD+RW. However, you can record and edit a

DVD-RW disc by choosing [Unfinalize] option.

1. Select [Finalize] option then press B.

2. Press ENTER while [Finalize] is selected.

Finalize menu appears.

3. Select [OK] then press ENTER.

The recorder starts finalizing the disc.

Note:

How long finalization takes depends on the type of

disc, how much is recorded on the disc, and the

number of titles on the disc.

Tips

 If you load a DVD-RW that has already been

finalized, you can ‘Unfinalize’ it by choosing

Unfinalize from the Finalize menu. After doing this,

you can edit and re-record onto the disc.

 You cannot unfinalize a DVD-R and DVD+R disc.

 If [Disc Protect] option is set to [ON], the finalize is

not available. To finalize, set [Disc Protect] option to

[OFF].

Stránka sa načítava...

LG DR-275 Návod na obsluhu

Tento návod je vhodný aj pre

LG DR-275 Návod na obsluhu

v iných jazykoch

Súvisiace články

Ostatné dokumenty