Philips S7720/26 Používateľská príručka

series S7000

1

17

16

22

24

18

23

25

19

21 20

2

4

3

5

7

8

13

6

10

9

12

11

15

14

series S7000

ENGLISH 4

БЪЛГАРСКИ 36

ČEŠTINA 73

EESTI 105

HRVATSKI 136

MAGYAR 168

ҚАЗАҚША 201

LIETUVIŠKAI 236

LATVIEŠU 267

МАКЕДОНСКИ 298

POLSKI 334

ROMÂNĂ 367

РУССКИЙ 400

SLOVENSKY 436

SLOVENŠČINA 469

SHQIP 510

SRPSKI 533

УКРАЇНСЬКА 567

4

Introduction

Congratulations on your purchase and

welcome to Philips! To fully benet from the support

that Philips offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Protection cap for cleansing brush attachment

(specic types only)

2 Click-on cleansing brush attachment

(specic types only)

3 Comb for beard styler attachment

(specic types only)

4 Click-on beard styler attachment

(specic types only)

5 Click-on trimmer attachment

(specic types only)

6 Click-on shaving unit

7 Handle

8 Socket for small plug

9 Battery charge indicator 1 light

10 Battery charge indicator 3 lights

11 ’Unplug for use’ symbol

12 Travel lock symbol

13 Replacement reminder

14 Cleaning reminder

15 Cleaning cartridge for SmartClean system

16 SmartClean system (specic types only)

17 Cap of SmartClean system

18 On/off button

19 Battery symbol

20 Ready symbol

21 Replacement symbol

22 Cleaning symbol

23 Adapter

ENGLISH

24 Small plug

25 Pouch

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Important safety information

Read this important information carefully before you

use the appliance and its accessories and save it for

future reference. The accessories supplied may vary

for different products.

Danger

- Keep the adapter dry.

Warning

- The adapter contains a transformer.

Do not cut off the adapter to replace it with

another plug, as this causes a hazardous situation.

- This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use

of the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not

be made by children without supervision.

- Always unplug the shaver before you clean it

under the tap.

- Always check the appliance before you use it.

Do not use the appliance if it is damaged, as this

may cause injury. Always replace a damaged part

with one of the original type.

ENGLISH 5

Caution

- Never immerse the cleaning system or the

charging stand in water and do not rinse it under

the tap.

- Never use water hotter than 80°C to rinse the

shaver.

- Only use this appliance for its intended purpose as

shown in the user manual.

- For hygienic reasons, the appliance should only be

used by one person.

- Never use compressed air, scouring pads, abrasive

cleaning agents or aggressive liquids such as petrol

or acetone to clean the appliance.

- If your shaver comes with a cleaning system,

always use the original Philips cleaning uid

(cartridge or bottle, depending on the type of

cleaning system).

- Always place the cleaning system on a stable,

level and horizontal surface to prevent leakage.

- If your cleaning system uses a cleaning cartridge,

always make sure that the cartridge compartment

is closed before you use the cleaning system to

clean or charge the shaver.

- When the cleaning system is ready for use, do not

move it to prevent leakage of cleaning uid.

- Do not use the adapter in or near wall sockets

that contain or have contained an electric air

freshener to prevent irreparable damage to the

adapter.

- Water may drip from the socket at the bottom

of the shaver when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed power unit inside the shaver.

ENGLISH6

Electromagnetic elds (EMF)

- This Philips appliance complies with all applicable

standards and regulations regarding exposure to

electromagnetic elds.

General

- This shaver is waterproof. It is suitable for use in

the bath or shower and for cleaning under the tap.

For safety reasons, the shaver can therefore only

be used without cord.

- The appliance is suitable for mains voltages ranging

from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe

low voltage of less than 24 volts.

- Maximum noise level: Lc = 69dB(A)

The display

Charging

Battery charge indicator with 3 lights

- Charging takes approx. 1 hour.

- Quick charge: When the appliance is connected

to the mains, the lights of the battery charge

indicator light up one after the other continuously.

When the appliance contains enough energy for

one shave, the bottom light of the battery charge

indicator starts ashing slowly.

- If you leave the appliance connected to the

mains, the charging process continues. To indicate

that the appliance is charging, rst the bottom

light ashes and then lights up continuously.

Then the second light ashes and then lights up

continuously, and so on until the appliance is fully

charged.

ENGLISH 7

Battery charge indicator with 1 light

- Charging takes approx. 1 hour.

- Quick charge: When the appliance does not

contain enough energy for one shave,

the battery charge indicator ashes fast.

When the battery charge indicator starts to ash

slowly, the appliance contains enough energy for

one shave.

- If you leave the appliance connected to the mains,

the charging process continues. To indicate that

the appliance is charging, the battery charge

indicator ashes slowly.

Battery fully charged

Note: This appliance can only be used without a cord.

Note: When the battery is full, the display switches off

automatically after 30 minutes. If you press the on/

off button during charging, the ‘unplug for use’ symbol

ashes white to remind you that you have

to disconnect the appliance from the mains.

When the battery is fully charged, all lights of the

battery charge indicator light up continuously.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

ENGLISH8

Battery low

When the battery is almost empty, the bottom light

ashes orange.

- Battery charge indicator with 3 lights

- Battery charge indicator with 1 light

Remaining battery capacity

Battery charge indicator with 3 lights

- The remaining battery capacity is indicated by the

lights of the battery charge indicator that light up

continuously.

’Unplug for use’ reminder

- The appliance is equipped with an ‘unplug for

use’ reminder. The ‘unplug for use’ starts to ash

to remind you that you have to disconnect the

appliance from the adapter before you can switch

it on.

ENGLISH 9

Cleaning reminder

For optimal shaving performance, we advise you to

clean the shaver after every use.

- When you switch off the shaver, the cleaning

reminder ashes to remind you to clean the

shaver.

Travel lock

You can lock the shaver when you are going to

travel. The travel lock prevents the shaver from being

switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode.

- While you activate the travel lock, the travel lock

symbol lights up continuously. When the travel

lock is activated, the travel lock symbol ashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

- The travel lock symbol ashes and then lights up

continuously.

The shaver is now ready for use again.

3 sec.

ENGLISH10

Replacing shaving heads

For maximum shaving performance, we advise you

to replace the shaving heads every two years.

- The appliance is equipped with a replacement

reminder which reminds you to replace the

shaving heads. The replacement reminder lights up

continuously.

Note: After replacing the shaving heads, you need to

reset the replacement reminder by pressing the on/off

button for 7 seconds.

Charging

Charging takes approx. 1 hour.

Note: This appliance can only be used without cord.

Charge the shaver before you use it for the rst

time and when the display indicates that the battery

is almost empty.

Charging with the adapter

1 Insert the small plug into the appliance and put

the adapter in the wall socket.

Charging in the SmartClean system

(specic types only)

1 Put the small plug in the SmartClean system.

2 Put the adapter in the wall socket.

2

1

ENGLISH 11

3 Press down the top cap to be able to place the

shaver in the holder (‘click’).

4 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

5 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to

connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate the

shaver is charging.

Using the shaver

Switching the appliance on and off

1 To switch on the appliance, press the on/off

button once.

2 To switch off the appliance, press the on/off

button once.

- Battery charge indicator with 3 lights: The display

lights up for a few seconds to show the remaining

battery status.

1

2

ENGLISH12

Shaving

Skin adaptation period

Your rst shaves may not bring you the result you

expect and your skin may even become slightly

irritated. This is normal. Your skin and beard need

time to adapt to any new shaving system.

We advise you to shave regularly (at least 3 times

a week) with this shaver for a period of 3 weeks to

allow your skin to adapt to the new shaver.

Note: This appliance can only be used without cord.

1 Switch on the appliance.

2 Move the shaving heads over your skin in

circular movements.

Note: Do not make straight movements.

3 Clean the shaver after use

(see chapter ‘Cleaning and maintenance’).

Wet shaving

You can also use this shaver in the shower or on a

wet face with shaving foam or shaving gel.

To shave with shaving foam or shaving gel, follow the

steps below:

1 Apply some water to your skin.

2 Apply shaving foam or shaving gel to your skin.

3 Rinse the shaving unit under the tap to ensure

that the shaving unit glides smoothly over your

skin.

4 Switch on the appliance.

ENGLISH 13

5 Move the shaving heads over your skin in

circular movements.

Note: Rinse the shaver under the tap regularly to ensure

that it continues to glide smoothly over your skin.

6 Dry your face and thoroughly clean the

shaver after use (see chapter ‘Cleaning and

maintenance’).

Note: Make sure you rinse all foam or shaving gel off

the shaver.

Using the click-on attachments

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Removing or attaching the click-on

attachments

1 Make sure that the appliance is switched off.

2 Pull the attachment straight off the appliance.

Note: Do not twist the attachment while you pull it off

the appliance.

3 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

ENGLISH14

Using the trimmer attachment

You can use the trimmer attachment to groom your

sideburns and moustache.

1 Make sure the appliance is switched off.

2 Insert the lug of the trimmer attachment into

the slot in the top of the appliance. Then press

down the trimmer attachment to attach it to

the appliance (‘click’).

3 Switch on the appliance.

4 You can now start trimming.

5 Clean the attachment after use

(see chapter ‘Cleaning and maintenance’).

Using the beard styler attachment

1 Make sure the appliance is switched off.

2 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

Using the beard styler attachment with

comb

You can use the beard styler attachment with the

comb attached to style your beard at one xed

setting, but also at different length settings. You can

use it also to pre-trim any long hairs before shaving

to have a more comfortable shave.

The hair length settings on the beard styler

attachment correspond to the remaining hair length

after cutting and range from 1 to 5mm.

1 Slide the comb straight into the guiding

grooves on both sides of the attachment

(‘click’).

ENGLISH 15

2 Press the length selector and then push it

to the left or right to select the desired hair

length setting.

3 Switch on the appliance.

4 You can now start styling your beard by

moving the attachment upwards with gentle

pressure making sure the front of the comb is

in full contact with the skin.

5 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

Using the beard styler attachment without

comb

You can use the beard styler attachment without the

comb to contour your beard, moustache, sideburns

or neckline to a length of 0.5mm.

1 Pull the comb off the attachment.

Note: Grab the comb in the centre to pull it off the

attachment. Do not pull at the sides of the comb.

2 Switch on the appliance.

3 You can now start contouring your beard,

moustache, sideburns or neckline by moving

the styler downwards with gentle pressure

while holding it perpendicular to the skin.

4 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

Using the cleansing brush attachment

Use the rotating cleansing brush attachment with

your daily cleansing cream. The cleansing brush

attachment removes oil and dirt, contributing to a

healthy and oil-free skin.

2

1

ENGLISH16

1 Insert the lug of the attachment into the slot

in the top of the appliance. Then press down

the attachment to attach it to the appliance

(‘click’).

2 Moisten the attachment with water.

Do not use the appliance with a dry brush

head, as this can irritate the skin.

Tip: Use the attachment before shaving for easier

shaving and a more hygienic shaving result.

3 Moisten your face with water and apply

a cleanser to your face.

4 Place the attachment on your right cheek.

5 Switch on the appliance.

6 Gently move the attachment across your skin

from the nose towards the ear. Do not push

the attachment too hard onto the skin to make

sure the treatment remains comfortable.

7 After approx. 20 seconds you can move the

appliance to your left cheek and start cleansing

this part of your face.

Caution: Do not clean the sensitive area around

your eyes.

20 sec.

ENGLISH 17

8 After approx. 20 seconds you can move

the attachment to your forehead and start

cleansing this part of your face. Gently move

the brush head from left to right.

Note: We advise you to not overdo the cleansing and to

not cleanse any zone longer than 20 seconds.

9 After the treatment, rinse and dry your face.

Your face is now ready for the next step of

your daily skincare routine.

10 Clean the attachment after use (see chapter

‘Cleaning and maintenance’).

Cleaning and maintenance

Note: The accessories supplied may vary for different

products. The box shows the accessories that have been

supplied with your appliance.

Cleaning the shaver in the SmartClean

system (specic types only)

Do not tilt the SmartClean system to prevent

leakage.

Note: Hold the SmartClean system while you prepare

it for use.

Note: If you clean the shaver in the SmartClean

system once a week, the SmartClean cartridge will last

approximately three months.

Preparing the SmartClean system for use

1 Put the small plug in the back of the

SmartClean system.

20 sec.

ENGLISH18

2 Put the adapter in the wall socket.

3 Press the button on the side of the SmartClean

system and lift the top part of the SmartClean

system.

4 Pull the seal off the cleaning cartridge.

5 Place the cleaning cartridge in the SmartClean

system.

6 Push the top part of the SmartClean system

back down (‘click’).

Using the SmartClean system

Always make sure to shake excess water off the

shaver before you place it in the SmartClean

system.

1

2

ENGLISH 19

1 Press down the top cap to be able to place the

shaver in the holder (‘click’).

2 Hold the shaver upside down above the holder.

Make sure the front of the shaver points

towards the SmartClean system.

3 Place the shaver in the holder, tilt the shaver

backwards and press down the top cap to

connect the shaver (‘click’).

- The battery symbol ashes slowly to indicate that

the shaver is charging.

4 Press the on/off button on the SmartClean

system to start the cleaning program.

- During the cleaning program (which takes approx.

10 minutes), the cleaning symbol ashes.

- When the cleaning program has been completed,

the ready symbol lights up continuously.

- The battery symbol lights up continuously to

indicate that the shaver is fully charged. This takes

approx. 1 hour.

Note: If you press the on/off button of the

SmartClean system during the cleaning program, the

program aborts. In this case, the cleaning symbol stops

ashing.

1

2

ENGLISH20

Stránka sa načítava ...

Philips S7720/26 Používateľská príručka

Táto príručka je tiež vhodná pre

Philips S7720/26 Používateľská príručka

V iných jazykoch

Súvisiace články