Hikoki G1813DE Používateľská príručka

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Pokyny na manipuláciu

Инструкция за експлоатация

Uputstvo za rukovanje

Upute za rukovanje

G 1812DE • G 1813DE • G 1813DF •

G 1813DVE • G 1813DVF

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

el

pl

hu

cs

tr

ro

sl

sk

bg

sr

hr

G1813DVE G1813DVF

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

el

pl

hu

cs

tr

ro

sl

sk

bg

sr

hr

uk

ru

2

1

G1813DVE

G1812DE /

G1813DE

G1813DVF

G1813DF

23

45

3

6

7

4

89

10 11

[G1812DE / G1813DE / G1813DVE]

[G1813DF / G1813DVF]

+ =

5

12 13

[G1813DVE / G1813DVF]

23456

1

n0

8000 min-1

3200 min-1

5500 min-1

15°–30°

ab

14 15

16

6

17

18 19

ab

20

7

English

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking up

or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation. If

damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and

speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-skid

safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

(Original instructions)

8

English

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another

battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

e) Do not use a battery pack or tool that is damaged

or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁ ed in the instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

SAFETY WARNINGS COMMON FOR

GRINDING OR ABRASIVE CUTTING-

OFF OPERATIONS

a) This power tool is intended to function as a

grinder or cut-oﬀ tool. Read all safety warnings,

instructions, illustrations and speciﬁ cations

provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

b) Operations such as sanding, wire brushing,

polishing or hole cutting are not recommended to

be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

c) Do not convert this power tool to operate in a way

which is not speciﬁ cally designed and speciﬁ ed by

the tool manufacturer.

Such a conversion may result in a loss of control and

cause serious personal injury.

d) Do not use accessories which are not speciﬁ cally

designed and speciﬁ ed by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not ensure safe operation.

e) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool.

Accessories running faster than their rated speed can

break and ﬂ y apart.

f) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

g) The dimensions of the accessory mounting must

ﬁ t the dimensions of the mounting hardware of the

power tool.

Accessories that do not match the mounting hardware of

the power tool will run out of balance, vibrate excessively

and may cause loss of control.

h) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no-load speed for one minute.

Damaged accessories will normally break apart during

this test time.

i) Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments.

The eye protection must be capable of stopping ﬂ ying

debris generated by various operations. The dust mask

or respirator must be capable of ﬁ ltrating particles

generated by your operation. Prolonged exposure to

high intensity noise may cause hearing loss.

j) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of workpiece or of a broken accessory may

ﬂ y away and cause injury beyond immediate area of

operation.

k) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting tool may contact hidden wiring.

Contact with a “live” wire will also make exposed metal

parts of the power tool “live” and could give the operator

an electric shock.

l) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

9

English

m) Never lay the power tool down until the accessory

has come to a complete stop.

The spinning accessory may grab the surface and pull

the power tool out of your control.

n) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

o) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

p) Do not operate the power tool near ﬂ ammable

materials.

Sparks could ignite these materials.

q) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED

WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction of

the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

a) Maintain a ﬁ rm grip with both hands on the power

tool and position your body and arm to allow you to

resist kickback forces. Always use auxiliary handle,

if provided, for maximum control over kickback or

torque reaction during start-up.

The operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

e) Do not attach a saw chain woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade.

Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC FOR

GRINDING AND ABRASIVE CUTTING-

OFF OPERATIONS

a) Use only wheel types that are speciﬁ ed for your

power tool and the speciﬁ c guard designed for the

selected wheel.

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

b) The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequately protected.

c) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheels must be used only for speciﬁ ed applications.

For example: do not grind with the side of cut-oﬀ

wheel.

Abrasive cut-oﬀ wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

e) Always use undamaged wheel ﬂ anges that are of

correct size and shape for your selected wheel.

Proper wheel ﬂ anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-oﬀ

wheels may be diﬀ erent from grinding wheel ﬂ anges.

f) Do not use worn down wheels from larger power

tools.

A wheel intended for larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

g) When using dual purpose wheels always use the

correct guard for the application being performed.

Failure to use the correct guard may not provide the

desired level of guarding, which could lead to serious

injury.

ADDITIONAL SAFETY WARNINGS

SPECIFIC FOR ABRASIVE CUTTING-

OFF OPERATIONS

a) Do not “jam” the cut-oﬀ wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind

the rotating wheel.

When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel

the spinning wheel and the power tool directly at you.

c) When the wheel is binding or when interrupting

a cut for any reason, switch oﬀ the power tool

and hold it motionless until the wheel comes to a

complete stop. Never attempt to remove the cut-

oﬀ wheel from the cut while the wheel is in motion

otherwise kickback may occur.

Investigate and take corrective action to eliminate the

cause of wheel binding.

d) Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut.

The wheel may bind, walk up or kickback if the power

tool is restarted in the workpiece.

10

English

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Use extra caution making a “pocket cut” into

existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

g) Do not attempt to do curved cutting.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage, which

can lead to serious injury.

GENERAL SAFETY INSTRUCTIONS

FOR CORDLESS DISC GRINDERS

– Attach the side handle ﬁ rmly, hold the housing and the

side handle with both hands, and support the tool body

securely. (Fig. 2)

– Check that speed marked on the wheel is equal to or

greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible with

the grinder;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are ﬁ tted in

accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are provided

with the bonded abrasive product and when they are

required;

– Ensure that the abrasive product is correctly mounted

and tightened before use and run the tool at no-load for

30 seconds in a safe position, stop immediately if there

is considerable vibration or if other defects are detected.

If this condition occurs, check the machine to determine

the cause;

– If a guard is equipped with the tool never use the tool

without such a guard;

– Do not use separate reducing bushings or adapters to

adapt large hole abrasive wheels;

– For tools intended to be ﬁ tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to

accept the spindle length;

– Do not use cutting oﬀ wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite ﬂ ammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, ﬁ rst disconnect the tool from

the mains supply (use non metallic objects) and avoid

damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves, helmet

and apron should be worn;

– Pay attention to the wheel that continues to rotate after

the tool is switched oﬀ .

– When using dual-purpose (combined grinding and cut-

oﬀ wheels), use only the type A wheel guard. (See page

274)

– When using a type A wheel guard for lateral grinding,

the guard may interfere with the workpiece causing poor

control.

– When using a type B wheel guard for cutting-oﬀ

operations with bonded cut-oﬀ wheels, there is an

increased risk of exposure to emitted sparks and

particles, as well as exposure to wheel fragments in the

event of a wheel burst.

– When using a type A, B wheel guard for cutting-oﬀ

operations or lateral grinding in concrete or masonry,

there is an increased risk of exposure to dust and loss of

control resulting in kickback.

– Do not use any segmented diamond cut-oﬀ wheels with

segment slits >10 mm. Only negative segment cutting

angles are permitted.

– The workpiece must lay ﬂ at and be secured against

slipping, e.g. using clamps. Large workpieces must be

suﬃ ciently supported.

– Observe the speciﬁ cations of the tool or accessory

manufacturer. Protect wheels from grease or impact.

– Accessories must be stored and handled with care in

accordance with the manufacturer's instructions.

WARNING

– When using a cutting-oﬀ wheel, be sure to attach a type

A wheel guard.

– When using a grinding wheel, be sure to attach a type B

wheel guard.

– For safety reasons, only use the wheel guard provided

for the respective accessory. Using an incorrect wheel

guard can lead to loss of control and serious injuries.

See also page 274.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the depressed center wheel to be utilized is

the correct type and free of cracks or surface defects.

Also ensure that the depressed center wheel is properly

mounted and the wheel nut is securely tightened.

2. Conﬁ rm that the push button is disengaged by pushing

push button two or three times before switching the

power tool on.

3. To prolong the life of the machine and ensure a ﬁ rst

class ﬁ nish, it is important that the machine should not

be overloaded by applying too much pressure. In most

applications, the weight of the machine alone is suﬃ cient

for eﬀ ective grinding. Too much pressure will result in

reduced rotational speed, inferior surface ﬁ nish, and

overloading which could reduce the life of the machine.

4. The wheel continues to rotate after the tool is switched

oﬀ .

After switching oﬀ the machine, do not put it down until

the depressed center wheel has come to a complete

stop. Apart from avoiding serious accidents, this

precaution will reduce the amount of dust and swarf

sucked into the machine.

5. When the machine is not use, the power source should

be disconnected.

6. Be sure to switch OFF and pull out the battery to avoid

a serious accident before the depressed center wheel is

assembling and disassembling.

7. Be careful of brake kickback.

This cordless disc grinder features an electric brake that

functions when the switch is released. As there is some

kickback when the brake functions, be sure to hold the

main body securely.

8. If you notice that the unit is generating unusually high

temperatures, operating poorly, or making abnormal

noises, immediately stop using and shut oﬀ the power

switch. Request an inspection and repair from the dealer

where you purchased the unit or a HiKOKI Authorized

Service Center.

Continuing to use while operating abnormally might

cause injuries.

9. If the unit is mistakenly dropped or strikes another object,

make a thorough check of the unit for cracks, breakage

or deformation, etc.

Injuries might occur if the unit has cracks, breakage or

deformation.

11

English

10. When working at elevated locations, clear the area of

other people and aware of conditions below you.

11. Always charge the battery at a temperature of 0°C–40°C.

A temperature of less than 0°C will result in over charging

which is dangerous. The battery cannot be charged at a

temperature higher than 40°C.

The most suitable temperature for charging is that of

20°C–25°C.

12. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

13. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

14. Never disassemble the rechargeable battery and

charger.

15. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

16. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

17. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

18. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or inﬂ ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

19. When using this unit continuously, the unit may overheat,

leading to damage in the motor and switch. Therefore,

whenever the housing becomes hot, give the tool a

break for a while.

20. Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

21. Do not use the product if the tool or the battery terminals

(battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

22. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the tool from

falling on the battery.

○ When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result in

smoke emission or ignition.

23. Always use the tool and battery at temperatures between

-5°C and 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery for a purpose other than those

speciﬁ ed.

5. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately stop

further recharging.

6. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

7. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

8. Do not use in a location where strong static electricity

generates.

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

10. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible and

ﬂ ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium

ion battery, the battery may be shorted, causing ﬁ re. When

storing the lithium ion battery, obey surely the rules of

following contents.

○ Do not place conductive debris, nail and wires such as

iron wire and copper wire in the storage case.

○ To prevent shorting from occurring, load the battery in

the tool or insert securely the battery cover for storing

until the ventilator is not seen.

12

English

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe the

following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100 Wh are considered to be in the freight classiﬁ cation

of Dangerous Goods and will require special application

procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

Power Output

2 to 3 digit number

USB DEVICE CONNECTION

PRECAUTIONS (UC18YSL3)

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the USB

device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

WARNING

○ Prior to use, check the connecting USB cable for any

defect or damage.

Using a defective or damaged USB cable can cause

smoke emission or ignition.

○ When the product is not being used, cover the USB port

with the rubber cover.

Buildup of dust etc. in the USB port can cause smoke

emission or ignition.

NOTE

○ There may be an occasional pause during USB

recharging.

○ When a USB device is not being charged, remove the

USB device from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

○ It may not be possible to charge some USB devices,

depending on the type of device.

NAMES OF PARTS (Fig. 1–Fig. 2

0

)

Motor Gear cover

Nameplate Depressed center

wheel (sold separately)

Push button Toolless wheel guard

Side handle Switch

Housing Hole of wheel guard

Switch panel Bump of lever

Filter Wheel washer (C)

Battery Wheel nut

Auto mode switch Wrench

Remaining battery

indicator switch

(Product)

Abrasive cutting

wheel

(sold separately)

Remaining battery

indicator lamp

(Product)

Diamond wheel

(sold separately)

Switch lever Oﬀ -lock lever

Dial Remaining battery

indicator switch

(Battery)

Guard clip (mounted

on wheel guard when

packaged)

Remaining battery

indicator lamp

(Battery)

Latch Mesh

Charge indicator lamp Soft brush

Tabs of guard clip

(2 locations) Diamond cup wheel

(sold separately)

Lever

Dust collection adapter

(For diamond cup

wheel)

(sold separately)

Bump of wheel guard Dust collection adapter

(For diamond wheel)

(sold separately)

Notch of body

SYMBOLS

WARNING

The following show symbols used for the machine. Be

sure that you understand their meaning before use.

G1812DE / G1813DE / G1813DF / G1813DVE /

G1813DVF:

Cordless Disc Grinder

To reduce the risk of injury, user must read

instruction manual.

Always wear eye protection.

Always operate the power tool with two hands

Not for cut-oﬀ operations

When using a cutting-oﬀ wheel, be sure to

attach the type A wheel guard.

when using a type B wheel guard for cutting-oﬀ

operations with bonded cut-oﬀ wheels, there is

an increased risk of exposure to emitted sparks

and particles, as well as exposure to wheel

fragments in the event of a wheel burst.

13

English

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive 2012/19/EU

on waste electrical and electronic equipment

and its implementation in accordance with

national law, electric tools that have reached

the end of their life must be collected separately

and returned to an environmentally compatible

recycling facility.

V Rated voltage

nRated speed

n0No-load rotation speed

min-1Revolution or reciprocations per minute

A Auto mode

D Wheel outer diameter

d Wheel hole diameter

t Wheel thickness

Peripheral speed

kg

Weight*

(According to EPTA-Procedure 01/2014)

Switching ON

Switching OFF

Disconnect the battery

Lock

Unlock

Auto mode switch

Warning

Remaining battery indicator switch

The battery remaining power is nearly empty.

Recharge the battery soonest possible

The battery remaining power is a half.

The battery remaining power is enough.

* Depending on attached battery. The heaviest weight is

measured with BSL36B18 (sold separately).

Also, the weight includes the wheel guard, side handle,

wheel washer, and wheel nut.

Battery

Lights ;

The battery remaining power is over 75%

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than 25%

Blinks ;

The battery remaining power is nearly empty.

Recharge the battery soonest possible.

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow it to

fully cool down.

Blinks ;

Output suspended due to failure or malfunction.

The problem may be the battery so please

contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed on page 275.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Removal of casting ﬁ n and ﬁ nishing of various types of

steel, bronze and aluminum materials and castings.

○ Grinding of welded sections or sections cut by means of

a cutting torch.

○ Grinding of synthetic resins, slate, brick, marble, etc.

SPECIFICATIONS

1. Power tool

The speciﬁ cations of this machine are listed in the Table on

page 273.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Electronic control

○ Soft start

Reduces recoil against the operator by managing the

number of rotations during startup.

○ Kickback Protection

The kickback protection feature cuts oﬀ the power to

the motor and stops the power tool in the event of a

sudden drop in the rotational speed of the wheel during

operation (for example, if the wheel locks during cutting

operation, etc.).

○ Overload protection

While working, if a load exceeding a certain level is

applied, or if the grinding disc is stopped for a certain

amount of time, the motor will be stopped to protect the

tool and for safety.

Turn oﬀ the switch once, then turn it on again to start up

the tool.

14

English

○ Rotation recovery control function

While working, if the tool is pressed too forcefully against

the surface and the motor stops, if you lift up the tool and

lighten the load, rotation will resume.

Depending on the grinding disc used and the working

conditions, the rotation recovery control may be stopped

by overload protection.

○ Overheat protection

This protection feature cuts oﬀ the power to the motor

and stops the power tool in the event of overheating of

motor during operation.

When the overheat protection feature has been

activated, the motor may stop.

In this case, release the tool switch and cool it down in a

few minutes.

After that you can use it again.

○ Restart prevention function

When the power is still switched on, the tool will not

restart when a battery is installed. This function can be

canceled once the tool is switched oﬀ .

○ Brake function

Brake activates when the switch is oﬀ .

○ Drop shut oﬀ function <G1813DVE>

When the drop shut oﬀ function has been activated, the

motor may stop.

In this case, release the tool switch.

After that you can use it again.

2. Battery

Model BSL1850

MA

Voltage 18 V

Battery capacity 5.0 Ah

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the charge indicator lamp will blink in red (At 1- second

intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 4 (on page 2).

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the charge

indicator lamp will light up in green. (See Table 1)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be as

shown in Table 1, according to the condition of the

charger or the rechargeable battery.

Table 1

Charger

status Status of indicator lamp Indication

meaning

Before

charging

ON/OFF at 0.5 sec.

intervals (RED) Plugged into

power source

*1

While

charging

Lights for 0.5 sec. at

intervals of 1 sec.

(BLUE) Charged at less

than 50%

Lights for 1 sec. at intervals

of 0.5 sec. (BLUE)

Charged at less

than 80%

Lights continuously

(BLUE) Charged at

more than 8

0

%

Charging

complete

Lights continuously

(GREEN)

(Continuous buzzer

sound: about 6 sec.)

Overheat

standby

ON/OFF at 0.3 sec.

intervals (RED)

Battery

overheated.

Unable to

charge. *2

Charging

impossible

ON/OFF at 0.1 sec.

intervals (PURPLE)

(Intermittent buzzer sound:

about 2 sec.)

Malfunction in

the battery or

the charger *3

*1 If the red lamp continues to blink even after the charger

has been attached, check to conﬁ rm that the battery has

been fully inserted.

*2 Although charging will start once the battery has cooled

down even when left in situ, the best practice is to

remove the battery and allow it to cool down in a shaded,

well-ventilated location before charging.

*3

○ Fully insert the battery.

○ Check to conﬁ rm that no foreign matter is stuck to the

battery mount or terminals.

○ Charging will take longer at extremely low ambient

temperatures. Charge the battery in a warm location

(such as indoors).

○ Do not block the air vent. Otherwise the interior will

overheat, reducing the charger’s performance.

○ If the cooling fan is not operating, contact a HiKOKI

Authorized Service Center for repairs.

(2) Regarding the temperatures and charging time of the

rechargeable battery

The temperatures and charging time will become as

shown in Table 2.

15

English

CAUTION

○ If the battery is charged while it is heated because

it has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the charge indicator lamp of the charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for

0.3 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○

When the charge indicator lamp ﬂ ickers (at 0.2-second

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 3 2

Charging 4 2

Attaching and removing the guard clip*152

Fitting and adjusting the wheel guard*263

Fixing the side handle 7 3

Assembling depressed center wheel*3, *4

84

Assembling cutting wheel and diamond

wheel*3, *494

Switch operation 1

0

4

Switching operation modes*511 4

Adjusting the number of revolution*5

(G1813DVE, G1813DVF) 12 5

Grinding angle and grinding method*613 5

Cutting work*7 14 5

Remaining battery indicator (Product)*8 15 5

Remaining battery indicator (Battery) 16 5

Charging a USB device from a

electrical outlet 18-a 6

Charging a USB device and battery

from a electrical outlet 18-b 6

How to recharge USB device 19 6

When charging of USB device is

completed 2

0

6

Selecting accessories ―276

*1 Attaching and removing the guard clip

Pull on the tabs while removing the guard clip.

When attaching the guard clip, ensure that its tabs

(2 locations) are hooked on the rim of the wheel guard.

*2 Fitting and adjusting the wheel guard

The wheel guard can be adjusted to an optimal angle for

the work.

Fix the wheel guard in place where its hole is aligned with

the bump of the lever before use.

*3 sold separately

*4 WARNING

Before use, be sure to tighten the wheel nut with the

included wrench.

Failure to tighten could result in the wheel nut

loosening when the brake is activated during a stop.

NOTE

The wheel washer is speciﬁ cally for this product. Do

not use it for any other product.

*5 About the mode change function

With Auto mode, you can lower noise and vibration by

lowering the maximum number of revolutions while in a

no-load state.

Table 2

Model UC18YSL3

Type of battery Li-ion

Charging voltage 14.4–18 V

Temperatures at which the

battery can be recharged 0°C–50°C

Charging time, for

battery capacity,

approx. (At 20°C)

1.5 Ah 15 min

2.0 Ah 20 min

2.5 Ah 25 min

3.0 Ah 20 min

(BSL1430C,

BSL1830C: 30 min)

4.0 Ah 26 min

(BSL1840M: 40 min)

5.0 Ah 32 min

6.0 Ah 38 min

8.0 Ah 52 min

Multi volt battery

1.5 Ah

(×2 unit) 20 min

2.5 Ah

(×2 unit) 32 min

4.

0

Ah

(×2 unit) 52 min

Number of battery cells 4–10

Charging voltage for USB 5 V

Charging current for USB 2 A

Weight 0.6 kg

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

16

English

While in Auto mode, the number of revolutions will be

raised if the load becomes greater during operation.

On the other hand, the number of revolutions will be

lowered if the load decreases during operation.

NOTE

○ To enable mode changes, pull the switch once after

installing the battery.

○ The set mode remains set even if the power is turned oﬀ .

○ Do not give a strong shock to the switch panel or break it.

It may lead to a trouble.

<G1813DVE, G1813DVF>

Pressing the Auto mode switch will change the

operating mode back and forth between Auto mode and

Transmission mode.

With Transmission mode, the grinder’s number of

revolutions can be set at one of six levels using the dial.

When operating in Transmission mode, the set number

of revolutions will be maintained regardless of changes

in load.

Set the mode and dial according to work application.

(Table 3)Table 3

Status Number of

Revolutions (min-1)Use

1 3200 Grinding stainless

steel

2 3800

Rust or paint removal

Grinding, ﬁ nishing

3 4700

4 5400

Rough grinding,

cutting

5 6700

6 8000

Auto L 5500 Light work, Standby state

Auto H 8000 Grinding, cutting

Auto L: No-load

Auto H: During operation

<G1812DE, G1813DE, G1813DF>

Pressing the Auto mode switch will change the operating

mode back and forth between Auto mode and Full-Speed

mode. In Full-Speed mode, the number of revolutions is

controlled so that it always remains constant.

Set the mode according to work application.

*6 Grinding angle and grinding method

Press down the machine evenly on the surface and

move back and forth so that the surface of the workpiece

does not become too hot.

Rough grinding: position the machine at an angle of

15°–30° for the best working results.

When the grinding stone is new, its corner may dig in

when it is pushed forward, so pull back during use.

(Fig. 13-a)

Once the wheel edge is worn, the workpiece can be

ground in both directions. (Fig. 13-b).

*7 Cutting work

Always work against the run of the disc. Otherwise there

is the danger of the machine kicking back from the cut

out of control. Guide the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

*8 Remaining battery indicator (Product)

When using a battery with a remaining battery indicator,

please refer to the indicator lamp on the battery for the

battery remaining power.

MAINTENANCE AND INSPECTION

WARNING

Be sure to turned oﬀ the switch and remove the battery

before maintenance and inspection.

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Filter cleaning and inspection (Fig. 17)

WARNING

Wear protective glasses and a dust mask when cleaning

the ﬁ lter with an air gun.

Failure to do so may result in inhalation or exposure of

the eyes to debris or dust.

After use, remove any debris or dust adhered to the ﬁ lter

using a soft brush. Check the ﬁ lter periodically to ensure that

it is free of scratching, chipping, or tearing. Replace with a

new ﬁ lter if the ﬁ lter is damaged in any way.

NOTE

○ If the mesh is clogged and the debris or dust cannot be

removed, detach the ﬁ lter and clean it with an air gun,

etc.

○ After cleaning, make sure to securely attach the ﬁ lter.

4. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

NOTE

In order to expel debris and dust, periodically run the

motor with no load.

5. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

6. Cleaning on the outside

When the cordless disc grinder is stained, wipe with a

soft dry cloth or a cloth moistened with soapy water. Do

not use chloric solvents, gasoline or paint thinner, for

they melt plastics.

7. Storage

Store the power tool and battery in a place in which

the temperature is less than 40°C and out of reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

17

English

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 96 dB (A)

Measured A-weighted sound pressure level: 85 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Sanding steel plate:

Vibration emission value ah = 5 m/s2

Uncertainty K = 1.5 m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use

of the power tool can diﬀ er from the declared total

value depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

○ The grinding thin sheets of metal or other easily vibrating

structures with a large surface can result in a total

emission much higher (up to 15 dB) than the declared

noise emission values.

Such workpieces should as far as possible be prevented

from emitting sound by suitable measures such as the

application of heavy ﬂ exible damping mats.

The increased noise emission is also to be considered

for both the risk assessment of noise exposure and

selecting adequate heating protection.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

18

Deutsch

f) Falls sich der Betrieb des Elektrowerkzeugs

in feuchter Umgebung nicht vermeiden lässt,

verwenden Sie eine Stromversorgung mit

Fehlerstromschutzeinrichtung (Residual

Current Device, RCD).

Durch den Einsatz einer

Fehlerstromschutzeinrichtung wird das Risiko eines

elektrischen Schlages reduziert.

3) Persönliche Sicherheit

a) Bleiben Sie wachsam, achten Sie auf das, was

Sie tun, und setzen Sie Ihren Verstand ein, wenn

Sie mit Elektrowerkzeugen arbeiten.

Benutzen Sie keine Elektrowerkzeuge, wenn

Sie müde sind oder unter Einﬂ uss von Drogen,

Alkohol oder Medikamenten stehen.

Bei der Arbeit mit Elektrowerkzeugen können bereits

kurze Phasen der Unaufmerksamkeit zu schweren

Verletzungen führen.

b) Benutzen Sie eine persönliche

Schutzausrüstung. Tragen Sie immer einen

Augenschutz.

Schutzausrüstung wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm und Gehörschutz

senken bei angemessenem Einsatz das

Verletzungsrisiko.

c) Vermeiden Sie unbeabsichtigtes Einschalten.

Achten Sie darauf, dass sich der Schalter

in der Aus- (Oﬀ -) Position beﬁ ndet, ehe Sie

das Gerät mit der Stromversorgung und/

oder Batteriestromversorgung verbinden, es

aufheben oder herumtragen.

Das Herumtragen von Elektrowerkzeugen mit

dem Finger am Schalter oder das Herstellen der

Stromversorgung bei betätigtem Schalter zieht

Unfälle regelrecht an.

d) Entfernen Sie sämtliche Einstellwerkzeuge

(Einstellschlüssel), ehe Sie das Elektrowerkzeug

einschalten.

Ein an einem beweglichen Teil des Elektrowerkzeugs

angebrachter Schlüssel kann zu Verletzungen

führen.

e) Überstrecken Sie sich nicht. Achten Sie jederzeit

darauf, sicher zu stehen und das Gleichgewicht

zu bewahren.

Dadurch haben Sie das Elektrowerkzeug in

unerwarteten Situationen besser im Griﬀ .

f) Tragen Sie geeignete Kleidung. Tragen Sie

keine lose Kleidung oder Schmuck. Halten Sie

Ihr Haar und Ihre Kleidung von beweglichen

Teilen fern.

Lose Kleidung, Schmuck oder langes Haar kann von

beweglichen Teilen erfasst werden.

g) Wenn Anschlüsse für Staubabsaug- und -

sammelvorrichtungen vorhanden sind, sorgen

Sie dafür, dass diese richtig angeschlossen und

eingesetzt werden.

Durch Entfernen des Staubes können

staubbezogene Gefahren vermindert werden.

h) Lassen Sie es nicht zu, dass die durch häuﬁ gen

Gebrauch von Werkzeugen erworbene

Vertrautheit Sie nachlässig macht und Sie

die Sicherheitsrichtlinien für das Werkzeug

ignorieren.

Eine unvorsichtige Handlung kann in

Sekundenbruchteilen zu schweren Verletzungen

führen.

ALLGEMEINE

SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Bitte beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und

Anweisungen zum späteren Nachschlagen auf.

Der Begriﬀ „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

1) Sicherheit im Arbeitsbereich

a) Sorgen Sie für einen sauberen und gut

ausgeleuchteten Arbeitsbereich.

Zugestellte oder dunkle Bereiche ziehen Unfälle

förmlich an.

b) Verwenden Sie Elektrowerkzeuge niemals an

Orten, an denen Explosionsgefahr besteht,

wie zum Beispiel in der Nähe von leicht

entﬂ ammbaren Flüssigkeiten, Gasen oder

Stäuben.

Bei der Arbeit mit Elektrowerkzeugen kann es zu

Funkenbildung kommen, wodurch sich Stäube oder

Dämpfe entzünden können.

c) Sorgen Sie bei der Arbeit mit Elektrowerkzeugen

dafür, dass sich keine Zuschauer (insbesondere

Kinder) in der Nähe beﬁ nden.

Wenn Sie abgelenkt werden, können Sie die

Kontrolle über das Werkzeug verlieren.

2) Elektrische Sicherheit

a) Elektrowerkzeuge müssen mit passender

Stromversorgung betrieben werden. Nehmen

Sie niemals irgendwelche Änderungen am

Anschlussstecker vor. Verwenden Sie bei

Elektrowerkzeugen mit Schutzkontakt (geerdet)

niemals Adapterstecker.

Stecker im Originalzustand und passende

Steckdosen reduzieren das Stromschlagrisiko.

b) Vermeiden Sie Körperkontakt mit geerdeten

Gegenständen wie Rohrleitungen, Heizungen,

Herden oder Kühlschränken.

Bei Körperkontakt mit geerdeten Gegenständen

besteht ein erhöhtes Stromschlagrisiko.

c) Setzen Sie Elektrowerkzeuge niemals Regen

oder sonstiger Feuchtigkeit aus.

Wenn Flüssigkeiten in ein Elektrowerkzeug

eindringen, erhöht sich das Stromschlagrisiko.

d) Verwenden Sie das Anschlusskabel nicht

missbräuchlich. Tragen Sie das Elektrowerkzeug

niemals am Stromkabel, ziehen Sie es nicht

damit heran und ziehen Sie den Stecker nicht

am Anschlusskabel aus der Steckdose.

Halten Sie das Anschlusskabel von Hitzequellen,

Öl, scharfen Kanten und beweglichen Teilen

fern.

Beschädigte oder verdrehte Anschlusskabel

erhöhen das Stromschlagrisiko.

e) Verwenden Sie, wenn Sie ein Elektrowerkzeug

im Freien benutzen, ein für den Außeneinsatz

geeignetes Verlängerungskabel.

Ein für den Außeneinsatz geeignetes Kabel

vermindert das Stromschlagrisiko.

(Übersetzung der Original-Gebrauchsanweisung)

19

Deutsch

4) Einsatz und Pﬂ ege von Elektrowerkzeugen

a) Überbeanspruchen Sie Elektrowerkzeuge nicht.

Benutzen Sie das richtige Elektrowerkzeug für

Ihren Einsatzzweck.

Das richtige Elektrowerkzeug erledigt seine Arbeit

bei bestimmungsgemäßem Einsatz besser und

sicherer.

b) Benutzen Sie das Elektrowerkzeug nicht, wenn

es sich nicht am Schalter ein- und ausschalten

lässt.

Jedes Elektrowerkzeug, das nicht mit dem Schalter

betätigt werden kann, stellt eine Gefahr dar und

muss repariert werden.

c) Ziehen Sie den Stecker der Stromversorgung

ab und/oder entfernen Sie den Akkupack

vom Elektrowerkzeug, falls abnehmbar, ehe

Sie Einstellarbeiten vornehmen, Zubehörteile

tauschen oder das Elektrowerkzeug verstauen.

Solche präventiven Sicherheitsmaßnahmen

verhindern den unbeabsichtigten Anlauf des

Elektrowerkzeugs und die damit verbundenen

Gefahren.

d) Lagern Sie nicht benutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern,

lassen Sie nicht zu, dass Personen das

Elektrowerkzeug bedienen, die nicht mit dem

Werkzeug selbst und/oder diesen Anweisungen

vertraut sind.

Elektrowerkzeuge in ungeschulten Händen sind

gefährlich.

e) Wartung von Elektrowerkzeugen und Zubehör.

Prüfen Sie sie auf Fehlausrichtungen,

Leichtgängigkeit beweglicher Teile,

Beschädigungen von Teilen und auf alle

anderen Umstände, die sich auf den Betrieb des

Elektrowerkzeugs auswirken können. Lassen

Sie das Elektrowerkzeug bei Beschädigungen

reparieren, ehe Sie es benutzen.

Viele Unfälle mit Elektrowerkzeugen sind auf

schlechte Wartung zurückzuführen.

f) Halten Sie Schneidwerkzeuge scharf und

sauber.

Richtig gewartete Schneidwerkzeuge mit scharfen

Schneiden bleiben weniger häuﬁ g hängen und sind

einfacher zu beherrschen.

g) Benutzen Sie Elektrowerkzeuge, Zubehör,

Werkzeugspitzen und Ähnliches in

Übereinstimmung mit diesen Anweisungen

– beachten Sie dabei die jeweiligen

Arbeitsbedingungen und die Art der

auszuführenden Arbeiten.

Der Gebrauch des Elektrowerkzeugs für andere

als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

h) Halten Sie Handgriﬀ e und Greiﬄ ächen trocken,

sauber und frei von Öl und Fett.

Rutschige Handgriﬀ e und Greiﬄ ächen lassen keine

sichere Handhabung und Kontrolle des Werkzeugs

in unerwarteten Situationen zu.

5) Verwendung und Pﬂ ege der Batterie

a) Laden Sie das Gerät nur mit dem vom Hersteller

empfohlenen Ladegerät auf.

Ein Ladegerät für einen speziellen Batterietyp

kann bei Verwendung mit anderen Batterien zu

Brandgefahr führen.

b) Verwenden Sie nur die für das Elektrowerkzeug

speziell empfohlenen Akkus.

Eine Verwendung von anderen Batterien kann zu

Verletzungen und Bränden führen.

c) Ist der Akku nicht in Gebrauch, achten Sie

darauf, dass er nicht mit Metallgegenständen,

beispielsweise Büroklammern, Münzen,

Schlüsseln, Nägeln, Schrauben oder anderen

kleinen Metallgegenständen in Kontakt kommt,

da diese Gegenstände einen Kurzschluss der

Anschlüsse verursachen können.

Ein Kurzschluss der Batterieanschlüsse kann zu

Verbrennungen oder Bränden führen.

d) Im Falle von missbräuchlichen Bedingungen

kann Flüssigkeit aus dem Akku austreten.

Vermeiden Sie in diesem Fall jeglichen Kontakt.

Sollten Sie dennoch mit der Batterieﬂ üssigkeit in

Berührung kommen, waschen Sie die betroﬀ ene

Stelle gründlich mit Wasser ab. Ist die Flüssigkeit

ins Auge geraten, suchen Sie einen Arzt auf.

Ausgetretene Batterieﬂ üssigkeiten können zu

Reizungen oder Verbrennungen führen.

e) Verwenden Sie keinen Akku oder kein Werkzeug,

der oder das beschädigt oder verändert ist.

Beschädigte oder veränderte Akkus können ein

unvorhersehbares Verhalten aufweisen, das zu einem

Feuer, einer Explosion oder Verletzung führen kann.

f) Setzen Sie den Akku oder das Werkzeug keinem

Feuer oder keiner zu hohen Temperatur aus.

Die Einwirkung von Feuer oder einer Temperatur

über 130°C kann zu einer Explosion führen.

g) Befolgen Sie alle Anweisungen zum Auﬂ aden

und laden Sie den Akku oder das Werkzeug

nicht außerhalb des Temperarturbereichs auf,

der in der Anleitung angegeben ist.

Wenn Sie den Akku falsch oder bei Temperaturen

außerhalb des angegebenen Bereichs auﬂ aden,

kann der Akku beschädigt werden und die Gefahr

eines Brandes steigen.

6) Service

a) Lassen Sie Ihr Elektrowerkzeug durch

qualiﬁ zierte Fachkräfte und nur unter Einsatz

der passenden Originalersatzteile warten.

Dies sorgt dafür, dass die Sicherheit des

Elektrowerkzeugs nicht beeinträchtigt wird.

b) Warten Sie niemals beschädigte Akkus.

Die Wartung von Akkus ist stets vom Hersteller oder

autorisierten Dienstleistern durchzuführen.

VORSICHT

Von Kindern und gebrechlichen Personen fernhalten.

Werkzeuge sollten bei Nichtgebrauch außerhalb der

Reichweite von Kindern und gebrechlichen Personen

aufbewahrt werden.

FÜR SCHLEIF- UND

TRENNSCHLEIFARBEITEN

GELTENDE SICHERHEITSHINWEISE

a) Dieses Elektrowerkzeug kann als Schleif- oder

Trennschleifwerkzeug eingesetzt werden. Bitte

beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

b) Es wird nicht empfohlen, Arbeiten wie

Sandpapierschleifen, Drahtbürsten, Polieren

oder Lochschneiden mit diesem Elektrowerkzeug

auszuführen.

Arbeiten, für die dieses Elektrowerkzeug nicht

konzipiert wurde, könnten eine Gefahr darstellen, die zu

Verletzungen oder Geräteschäden führen könnten.

20

Deutsch

c) Bauen Sie dieses Elektrowerkzeug nicht so um,

dass es auf eine Art und Weise verwendet wird, die

nicht ausdrücklich vom Hersteller des Werkzeugs

vorgesehen und angegeben ist.

Ein solcher Umbau kann zum Verlust der Kontrolle über

das Werkzeug führen und eine schwere Verletzung

verursachen.

d) Verwenden Sie keine Zubehörteile, die nicht

speziell vom Hersteller für die Verwendung mit dem

Werkzeug entwickelt und angegeben wurden.

Der Umstand, dass ein Zubehörteil an dem

Elektrowerkzeug angebracht werden kann, bedeutet

nicht, dass damit ein sicherer Betrieb garantiert ist.

e) Die Nenndrehzahl des Schleifkörpers muss

mindestens der maximalen auf dem Elektrowerkzeug

angegebenen Drehzahl entsprechen.

Schleifkörper, die mit einer höheren Geschwindigkeit

als ihrer Nenndrehzahl betrieben werden, können

zerbersten und in Folge können Bruchstücke davon

weggeschleudert werden.

f) Außendurchmesser und Dicke des Schleifkörpers

müssen den Maßangaben Ihres Elektrowerkzeugs

entsprechen.

Falsch bemessene Schleifkörper können nicht

ausreichend abgesichert oder bei Arbeit nicht

ausreichend kontrolliert werden.

g) Die Abmessungen der Zubehörbefestigung müssen

mit den Abmessungen der Befestigungselemente

des Elektrowerkzeugs übereinstimmen.

Zubehör, das nicht auf den Montageaufsatz des

Elektrowerkzeugs passt, läuft mit Unwucht, vibriert sehr

stark und kann zu einem Verlust der Kontrolle über das

Werkzeug führen.

h) Benutzen Sie niemals beschädigte

Schleifkörper. Überprüfen Sie vor jedem

Gebrauch Einsatzwerkzeuge wie Schleifkörper

auf Absplitterungen und Risse, Schleifteller

auf Sprünge, Risse oder starke Abnutzung,

Drahtbürsten auf lose oder gebrochene

Drähte. Wenn das Elektrowerkzeug oder der

Schleifkörper herunter fällt, überprüfen Sie es/

ihn auf Beschädigung oder montieren Sie einen

unbeschädigten Schleifkörper. Lassen Sie nach

Prüfung und Montage des Schleifkörpers das

Elektrowerkzeug eine Minute lang mit maximaler

Leerlaufdrehzahl laufen. Achten Sie dabei darauf,

dass Sie und alle anderen in der Nähe beﬁ ndlichen

Personen sich außerhalb der Rotationsebene des

Schleifkörpers aufhalten.

Normalerweise zerbersten schadhafte Schleifwerkzeuge

bei einem solchen Probelauf.

i) Tragen Sie eine Schutzausrüstung. Benutzen

Sie je nach Anwendung Gesichtsschutz oder

Schutzbrille. Soweit angemessen, tragen Sie eine

Staubmaske, einen Gehörschutz, Handschuhe

sowie eine Arbeitsschürze, die geeignet sind,

Sie vor Schleifkörper- und Werkstückteilen zu

schützen.

Die Schutzbrille muss sich eignen, die bei

unterschiedlichen Arbeiten weggeschleuderten Partikel

abzuwehren. Die Staub- oder die Atemschutzmaske

muss in der Lage sein, die bei der Arbeit entstehenden

Partikel zu ﬁ ltern. Eine dauerhaft hohe Lärmbelastung

kann zu Gehörverlust führen.

j) Halten Sie umstehende Personen von Ihrem

Arbeitsbereich fern. Jeder, der den Arbeitsbereich

betritt, muss eine Schutzausrüstung tragen.

Werkstückteile oder Stücke geborstener Schleifkörper

können weggeschleudert werden und auch außerhalb

des unmittelbaren Arbeitsbereiches Verletzungen

verursachen.

k) Halten Sie das Elektrowerkzeug bei Arbeiten,

bei denen das Schneidwerkzeug verborgene

Stromleitungen berühren könnte, nur an den

isolierten Griﬀ ﬂ ächen.

Der Kontakt mit stromführenden Leitungen setzt

auch freiliegende Metallteile des Elektrowerkzeugs

unter Strom und könnte für den Bediener zu einem

Stromschlag führen.

l) Halten Sie die Anschlussleitung des

Elektrowerkzeugs stets vom drehenden

Schleifkörper fern.

Falls Sie die Kontrolle über das Elektrowerkzeug

verlieren, kann die Anschlussleitung durchtrennt oder

erfasst werden, und Ihre Hand oder Ihr Arm in das sich

drehende Einsatzwerkzeug geraten.

m) Legen Sie das Elektrowerkzeug niemals ab, bevor

der Schleifkörper vollständig zum Stillstand

gekommen ist.

Der sich drehende Schleifkörper kann in Berührung mit

der Ablageﬂ äche geraten, wodurch Sie die Kontrolle

über das Elektrowerkzeug verlieren können.

n) Lassen Sie das Elektrowerkzeug nicht laufen,

während Sie es tragen.

Der sich drehende Schleifkörper kann bei versehentlicher

Berührung Ihre Kleidung erfassen und in Ihren Körper

gezogen werden.

o) Reinigen Sie regelmäßig die Lüftungsöﬀ nungen

des Elektrowerkzeugs.

Übermäßige Ansammlungen von Metallstaub könnten

zu elektrischen Gefährdungen führen.

p) Verwenden Sie das Elektrowerkzeug nicht in der

Nähe entﬂ ammbarer Materialien.

Funken könnten diese Materialien entzünden.

q) Verwenden Sie keine Zubehörteile, die ﬂ üssige

Kühlmittel erfordern.

Die Verwendung von Wasser oder anderen ﬂ üssigen

Kühlmitteln kann zu einem elektrischen Schlag oder

Schock führen.

RÜCKSCHLAG UND DAZU

GEHÖRIGE SICHERHEITSHINWEISE

Rückschlag ist die plötzliche Reaktion infolge eines

Verklemmens oder Verhakens eines drehenden

Schleifkörpers, eines Schleiftellers oder einer Drahtbürste

etc. Dieses Verklemmen oder Verhaken führt zu einem

plötzlichen Stopp des rotierenden Schleifkörpers, wodurch

ein unkontrolliertes Elektrowerkzeug an der Blockierstelle

ruckartig gegen die Drehrichtung des Schleifkörpers bewegt

wird.

Wenn beispielsweise eine Schleifscheibe im Werkstück

verklemmt oder verhakt wird, kann sich die Kante der

in die Blockierstelle eindringenden Schleifscheibe in

die Oberﬂ äche des Werkstücks graben, wodurch die

Schleifscheibe ausbrechen oder einen Rückschlag

verursachen kann. Je nach Drehrichtung der Scheibe an

der Blockierstelle kann sich die Schleifscheibe dabei auf die

Bedienperson zu oder von ihr weg bewegen.

Schleifscheiben können unter diesen Umständen auch

brechen.

Zum Rückschlag kommt es in Folge einer falschen

und/ oder nicht ordnungsgemäßen Verwendung

des Elektrowerkzeugs. Dies kann durch geeignete

Vorsichtsmaßnahmen vermieden werden, die im Folgenden

beschrieben werden.

Stránka sa načítava ...

Hikoki G1813DE Používateľská príručka

Táto príručka je tiež vhodná pre

Hikoki G1813DE Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty