AEG WS 10-115 Používateľská príručka

Original instructions

Originalbetriebsanleitung

Notice originale

Istruzioni originali

Manual original

Oorspronkelijke gebruiksaanwijzing

Original brugsanvisning

Original bruksanvisning

Bruksanvisning i original

Alkuperäiset ohjeet

Πρωτότυπο οδηγιών χρήσης

Orijinal işletme talimatı

Původním návodem k používání

Pôvodný návod na použitie

Instrukcją oryginalną

Eredeti használati utasítás

Izvirna navodila

Originalne pogonske upute

Instrukcijâm oriěinâlvalodâ

Originali instrukcija

Algupärane kasutusjuhend

Оригинальное руководство по

эксплуатации

Оригинално ръководство за

експлоатация

Instrucţiuni de folosire originale

Оригинален прирачник за работа

Оригінал інструкції з експлуатації

WS 10-115, WS 10-125,

WS 12-115, WS 12-125, WS 13-125 XE

https://manual-hub.com/

Technical Data,Safety Instructions, Specied Conditions of Use,

Mains connection, Maintenance, Symbols Please read and save

these instructions!

English

14

Technische Daten, Sicherheitshinweise, Bestimmungsgemäße Verwendung,

Netzanschluss, Wartung, Symbole Bitte lesen und

aufbewahren!

Deutsch

18

Caractéristiques techniques, Instructions de sécurité, Utilisation conforme aux

prescriptions, Branchement secteur, Entretien, Symboles A lire et à conserver

soigneusement

Français

22

Dati tecnici,Norme di sicurezza,Utilizzo conforme, Collegamento alla rete,

Manutenzione, Simboli Si prega di leggere e

conservare le istruzioni!

Italiano

26

Datos técnicos, Instrucciones de seguridad, Aplicación de acuerdo a la nalidad,

Conexión eléctrica, Mantenimiento, Símbolos Lea y conserve estas

instrucciones por favor!

Español

30

Características técnicas, Instruções de segurança, Utilização autorizada,

Ligação à rede, Manutenção, Symbole Por favor leia e conserve

em seu poder!

Português

34

Technische gegevens, Veiligheidsadviezen, Voorgeschreven gebruik van het

systeem, Netaansluiting,Onderhoud, Symbolen Lees en let goed

op deze adviezen!

Nederlands

38

Tekniske data, Sikkerhedshenvisninger, Tiltænkt formål, Nettilslutning,

Vedligeholdelse, Symboler Vær venlig at læse

og Opbevare!

Dansk

42

Tekniske data, Spesielle sikkerhetshenvisninger, Formålsmessig bruk,

Nettilkopling, Vedlikehold, Symboler Vennligst les og oppbevar!

Norsk

46

Tekniska data, Säkerhetsutrustning, Använd maskinen Enligt anvisningarna,

Nätanslutning, Skötsel, Symboler Läs igenom och spara!

Svenska

50

Tekniset arvot, Turvallisuusohjeet, Tarkoituksenmukainen käyttö,

Verkkoliitäntä, Huolto, Symbolit Lue ja säilytö!

Suomi

54

Τεχνικά στοιχεία, Ειδικές υποδείξεις ασφάλειας, Χρήση σύμφωνα με το σκοπό

προορισμού, Μπαταρίες, Χαρακτηριστικά, Συντήρηση, Σύμβολα.

Ελληνικά

58

Teknik veriler, Güvenliğiniz için talimatlar, Kullanim, Şebeke bağlantisi,

Bakim, Semboller Lütfen okuyun ve saklayın

Türkçe

63

Technická data, Speciální bezpečnostní upozornění, Oblast využití,

Připojení na sít, Údržba, Symboly Po přečtení uschovejte

Česky

67

Technické údaje, Špeciálne bezpčènostné pokyny, Použitie podl’a predpisov,

Siet’ová prípojka, Údrzba, Symboly Prosím prečítať a uschovať!

Slovensky

71

Dane techniczne, Specjalne zalecenia dotyczące bezpiecze´nstwa,

Użytkowanie zgodne z przeznaczeniem, Podłączenie do sieci, Gwarancja, Symbole Należy uważnie przeczytać i

zachować do wglądu!

Polski

75

Műszaki adatok, Különleges biztonsági tudnivalók, Rendeltetésszerű használat,

Hálózati csatlakoztatás, Karbantartás, Szimbólumok Olvassa el és őrizze meg

Magyar

79

Tehnični podatki, Specialni varnostni napotki, Uporaba v skladu z namembnostjo,

Omrežni priključek, Vzdrževanje, Simboli Prosimo preberite

in shranite!

Slovensko

83

Tehnički podaci, Specijalne sigurnosne upute, Propisna upotreba,

Priključak na mrežu, Održavanje, Simboli Molimo pročitati i sačuvati

Hrvatski

87

Tehniskie dati, Speciālie drošības noteikumi, Noteikumiem atbilstošs izmantojums,

Tīkla pieslēgums, Apkope, Simboli Pielikums lietošanas pamācībai

Latviski

91

Techniniai duomenys, Ypatingos saugumo nuorodos, Naudojimas pagal paskirti,

Elektros tinklo jungtis, Techninis aptarnavimas, Simboliai Prašome perskaityti

ir neišmesti!

Lietuviškai

95

Tehnilised andmed, Spetsiaalsed turvajuhised, Kasutamine vastavalt otstarbele,

Võrku ühendamine, Hooldus, Sümbolid Palun lugege läbi ja hoidke alal!

Eesti

99

Òåõíè÷åñêèå äàííûå, Ðåêîìåíäàöèè ïî òåõíèêå áåçîïàñíîñòè,

Èñïîëüçî- âàíèå, Îáñëóæèâàíèå, Ñèìâîëû

Пожалуйста прочтите и

сохраните эту инструкцию.

Pусский

103

Òåõíè÷åñêè äàííè, Ñïåöèàëíè óêàçàíèÿ çà áåçîïàñíîñò, Èçïîëçâàíå ïî

ïðåäíàçíà÷åíèå, Ñâúðçâàíå êúì ìðåæàòà, Ïîääðúæêà, Ñèìâîëè Моля прочетете и запазете!

Български

108

Date tehnice, Instrucţiuni de securitate, Condiţii de utilizare specifcate,

Acumulatori, Intreţinere, Simboluri Va rugăm citiţi şi păstraţi

aceste instrucţiuni

Română

112

Òåõíè÷êè Ïîäàòîöè, Óïàòñòâî Çà Óïîòðåáà, Ñïåöèôèöèðàíè Óñëîâè

Íà Óïîòðåáà, БАТЕРИИ, Îäðæóâàњå, Ñèìáîëè

Ве мoлиме прочитаjте го и

чувајте го ова упатство!

Мaкeдohcки

116

Технічні характеристики, Вказівки З Техніки Безпеки, Використання за призначенням,

Підключення до мережі, Обслуговування, Символи Прочитайте та збережіть

цю інструкцію.

Українська

120





       



127

https://manual-hub.com/

TIP

VII

IX

V

IV

VIII

I II III

VI

Accessory

Zubehör

Accessoires

Accessorio

Accessorio Acessório

Toebehoren Tilbehør

Tilbehør Tillbehör

Lisälaite 

Aksesuar Příslušenství

Príslušenstv 

Azokat a tartozékokat

Oprema Piederumi

Priedas Tarvikud

Äîïîëíèòåëü



Accesoriu 

 



https://manual-hub.com/

2

I

A B

https://manual-hub.com/

3

II

1. 2.

4.3.

1

2

https://manual-hub.com/

4

III

0°

30°

60° 60°

30

°

60

°

30

°

60

°

0

°

30°

https://manual-hub.com/

5

IV

2.

1.

3.

< 6 mm

> 6 mm

4.

https://manual-hub.com/

6

IV

3.

2.1.

https://manual-hub.com/

7

IV

1. 2.

3.

WS ...-... X...

https://manual-hub.com/

8

V

Stop

Start

https://manual-hub.com/

9

VI

A...B...C...D...E

C

WS ...-... E...

https://manual-hub.com/

10

TIP

< 30°

TIP

VII

https://manual-hub.com/

11

VIII

1. 2.

Accessory

Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid

Äîïîëíèòåëü



Accesoriu







https://manual-hub.com/

12

VIII

Accessory

Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid

Äîïîëíèòåëü



Accesoriu







1.

3.

2.

https://manual-hub.com/

13

VIII

3.

2.1.

Accessory

Zubehör

Accessoires

Accessorio

Acessório

Toebehoren

Tilbehør

Tillbehör

Lisälaite



Aksesuar



Príslušenstv



Tartozékokat

Oprema

Piederumi

Prieda

Tarvikud

Aksessuaarid

Äîïîëíèòåëü



Accesoriu







https://manual-hub.com/

14

GB

English

TECHNICAL DATA

Angle Grinder WS 10-115 WS 10-125 WS 12-115 WS 12-125 WS 13-125 XE

Rated input 1000 W 1000 W 1200 W 1200 W 1300 W

Rated speed 11500 min -1 11500 min -1 11500 min -1 11500 min -1 2800 - 11500 min -1

D= Grinding disk diameter max.

d= Grinding disk hole diameter

115 mm

22,2 mm 125 mm

22,2 mm 115 mm

22,2 mm 125 mm

22,2 mm

b= Cutting disk thickness min. / max.

1/3 mm 1/3 mm 1/3 mm 1/3 mm 1/3 mm

b= Grinding disk thickness max. 6 mm 6 mm 6 mm 6 mm 6 mm

D= Grinding surface diameter max. 115 mm 125 mm 115 mm 125 mm 125 mm

D= Wiring brush diameter max. 75 mm 75 mm 75 mm 75 mm 75 mm

Thread of work spindle M 14 M 14 M 14 M 14 M 14

Weight according EPTA-Procedure 01/2003 2,3 kg 2,3 kg 2,4 kg 2,4 kg 2,4 kg

Noise information

Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A)) 87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 90,1 dB (A)

Sound power level (Uncertainty K=3dB(A)) 98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 101,1 dB (A)

Wear ear protectors!

Vibration information

Vibration total values (triaxial vector sum) determined according to EN 60745

Surface grinding:

Vibration emission value ah,SG

Uncertainty K=

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

8,0 m/s2

1,5 m/s2

Disk sanding:

Vibration emission value ah,DS

Uncertainty K=

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

7,5 m/s2

1,5 m/s2

For other applications, e.g. Abrasive Cutting-O Operations or Wire Brushing other vibration values could occur.

WARNING!

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745

and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for dierent applications,

with dierent accessories or poorly maintained, the vibration emission may dier. This may signicantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is

running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the eects of vibration such as: maintain the tool and the accessories,

keep the hands warm, organisation of work patterns.

WARNING!

Read all safety warnings and all instructions. Failure to

follow the warnings and instructions may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire

Brushing or Abrasive Cutting-O Operations:

a) This power tool is intended to function as a grinder,

sander, wire brush or cut-o tool. Read all safety warnings,

instructions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

b) Operations such as polishing are not recommended

to be performed with this power tool.Operations for which

the power tool was not designed may create a hazard and cause

personal injury.

c) Do not use accessories which are not specically

designed and recommended by the tool manufacturer. Just

because the accessory can be attached to your power tool, it does

not assure safe operation.

d) The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Accesso-

ries running faster than their rated speed can break and y apart.

https://manual-hub.com/

15

GB

English

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power

tool. Incorrectly sized accessories cannot be adequately guarded

or controlled.

f) Threaded mounting of accessories must match the grin-

der spindle thread. For accessories mounted by anges, the

arbour hole of the accessory must t the locating diameter

of the ange. Accessories that do not match the mounting hard-

ware of the power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart during this

test time.

h) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors, gloves

and shop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of

stopping ying debris generated by various operations. The dust

mask or respirator must be capable of ltrating particles generated

by your operation. Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal protec-

tive equipment. Fragments of workpiece or of a broken accessory

may y away and cause injury beyond immediate area of operation.

j) Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting accessory

contacting a „live“ wire may make exposed metal parts of the power

tool „live“ and could give the operator an electric shock.

k) Position the cord clear of the spinning accessory. If you lose

control, the cord may be cut or snagged and your hand or arm may be

pulled into the spinning wheel.

l) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

m) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

o) Do not operate the power tool near ammable materials.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or snag-

ging causes rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also break

under these conditions.

Kickback is the result of power tool misuse and/or incorrect opera-

ting procedures or conditions and can be avoided by taking proper

precautions as given below.

a) Maintain a rm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper precautions

are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool in

direction opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of control.

Safety Warnings Specic for Grinding and Abrasive Cutting-

O Operations:

a) Use only wheel types that are recommended for your

power tool and the specic guard designed for the selected

wheel. Wheels for which the power tool was not designed cannot be

adequately guarded and are unsafe.

b) The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard helps

to protect the operator from broken wheel fragments, accidental

contact with wheel and sparks that could ignite clothing.

c) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-o wheel. Abra-

sive cut-o wheels are intended for peripheral grinding, side forces

applied to these wheels may cause them to shatter.

d) Always use undamaged wheel anges that are of correct

size and shape for your selected wheel. Proper wheel anges

support the wheel thus reducing the possibility of wheel breakage.

Flanges for cut-o wheels may be dierent from grinding wheel

anges.

e) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the higher

speed of a smaller tool and may burst.

Additional Safety Warnings Specic for Abrasive Cutting-O

Operations:

a) Do not “jam” the cut-o wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

https://manual-hub.com/

16

GB

English

binding of the wheel in the cut and the possibility of kickback or wheel

breakage.

b) Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch o the power tool and hold the power tool

motionless until the wheel comes to a complete stop. Never

attempt to remove the cut-o wheel from the cut while the

wheel is in motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is restarted in

the workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to sag

under their own weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on both sides

of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specic for Sanding Operations:

a) Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may cause snagging,

tearing of the disc or kickback.

Safety Warnings Specic for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the wires

by applying excessive load to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing,

do not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in diameter due

to work load and centrifugal forces.

Additional Safety and Working Instructions

When grinding metal, ying sparks are produced. Take care that

no persons are endangered. Because of the danger of re, no

combustible materials should be located in the vicinity (spark ight

zone). Do not use dust extraction.

Avoid ying sparks and sanding dust hit your body.

Never reach into the danger area of the machine when it is running.

Immediately switch o the machine in case of considerable vibra-

tions or if other malfunctions occur. Check the machine in order to

nd out the cause.

Under extreme conditions (e.g. smooth-grinding metals with

the arbour and vulcanized bre grinding disk), signicant

contamination can build up on the inside of the angle grinder. For

safety reasons, in such conditions a ground fault interrupter must

be connected in series. If the ground fault interrupter trips the

machine must be sent for service.

Chips and splinters must not be removed while the machine is

running.

MAINS CONNECTION

Connect only to single-phase AC system voltage as indicated on

the rating plate. It is also possible to connect to sockets without an

earthing contact as the design conforms to safety class II.

Appliances used at many dierent locations including wet room

and open air must be connected via a residual current device (FI,

RCD, PRCD) of 30mA or less.

Only plug-in when machine is switched o.

Do not let any metal parts enter the airing slots - danger of short

circuit!

Inrush currents cause short-time voltage drops. Under unfavoura-

ble power supply conditions, other equipment may be aected. If

the system impedance of the power supply is lower than 0,2 Ohm,

disturbances are unlikely to occur.

SPECIFIED CONDITIONS OF USE

The angle grinder is intended for grinding and cutting metal, stone

and ceramicmaterials as well as sanding and wire brushing.

Use the cutting guard from the accessories range for cutting

application.

Please refer to the instructions supplied by the accessory

manufacturer.

The machine is suitable only for working without water.

WORKING INSTRUCTIONS

For accessories intended to be tted with threaded hole wheel,

ensure that the thread in the wheel is long enough to accept the

spindle length.

Always use and store the cutting and grinding disks according to

the manufacturer‘s instructions.

Always use the correct guard for cutting and grinding.

The grinding surface of the centre depressed disks must be moun-

ted min. 2 mm below the plane of the guard lip.

The adjusting nut must be tightened before starting to work with

the machine.

Always use the auxiliary handle.

The workpiece must be xed if it is not heavy enough to be steady.

Never move the workpiece towards the rotating disk by hand.

The ange nut must be securely tightened before the machine is

started.

If the tool is not securely tightened with the ange nut, it is pos-

sible that the tool will lose the required clamping force when it is

decelerated.

In the event that a power failure occurs whilst the machine is

operating, the brake function will be inoperative.

ELECTRONICS

WS 13-125 XE: The built-in electronic will keep a constant speed

even under increased load. In case of overload, the rotational speed

is being reduced until machine stops.

Electronic smooth start for save use prevents jerky run-up of the

machine.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.

If the supply cord of this power tool is damaged, it must be

replaced by a specially prepared cord available through the service

organization.

https://manual-hub.com/

17

GB

English

Use only AEG accessories and spare parts. Should components need to

be replaced which have not been described, please contact one of our

AEG service agents (see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please state

the Article No. as well as the machine type printed on the label

and order the drawing at your local service agents or directly at:

Techtronic Industries GmbH, Max-Eyth-Straße10, 71364Winnen-

den, Germany.

SYMBOLS

CAUTION! WARNING! DANGER!

Please read the instructions carefully before starting the

machine.

Always wear goggles when using the machine.

Wear gloves!

Always disconnect the plug from the socket before

carrying out any work on the machine.

Do not use force.

Only for cutting work.

Only for grinding.

Accessory - Not included in standard equipment, availa-

ble as an accessory.

Do not dispose of electric tools together with household

waste material. Electric tools and electronic equipment

that have reached the end of their life must be collected

separately and returned to an environmentally compatible

recycling facility. Check with your local authority or retailer

for recycling advice and collection point.

Class II tool. Tool in which protection against electric

shock does not rely on basic insulation only, but in which

additional safety precautions, such as double insulation

or reinforced insulation, are provided. There being

no provision for protective earthing or reliance upon

installation conditions.

UkrSEPRO Conformity Mark

EurAsian Conformity Mark

https://manual-hub.com/

18

D

Deutsch

TECHNISCHE DATEN

Winkelschleifer WS 10-115 WS 10-125 WS 12-115 WS 12-125 WS 13-125 XE

Nennaufnahmeleistung 1000 W 1000 W 1200 W 1200 W 1300 W

Nenndrehzahl 11500 min -1 11500 min -1 11500 min -1 11500 min -1 2800 - 11500 min -1

D= Schleifscheibendurchmesser max.

d= Bohrungsdurchmesser

115 mm

22,2 mm 125 mm

22,2 mm 115 mm

22,2 mm 125 mm

22,2 mm

b= Trennscheibendicke min. / max.

1/3 mm 1/3 mm 1/3 mm 1/3 mm 1/3 mm

b= Schleifscheibendicke max. 6 mm 6 mm 6 mm 6 mm 6 mm

D= Schleiächendurchmesser max. 115 mm 125 mm 115 mm 125 mm 125 mm

D= Topfbürstendurchmesser max. 75 mm 75 mm 75 mm 75 mm 75 mm

Spindelgewinde M 14 M 14 M 14 M 14 M 14

Gewicht nach EPTA-Prozedur 01/2003 2,3 kg 2,3 kg 2,4 kg 2,4 kg 2,4 kg

Geräuschinformation

Messwerte ermittelt entsprechend EN 60745. Der A-bewertete Geräuschpegel des Gerätes beträgt typischerweise:

Schalldruckpegel (Unsicherheit K=3dB(A)) 87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 87,1 dB (A) 90,1 dB (A)

Schallleistungspegel (Unsicherheit K=3dB(A)) 98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 98,1 dB (A) 101,1 dB (A)

Gehörschutz tragen!

Vibrationsinformationen

Schwingungsgesamtwerte (Vektorsumme dreier Richtungen) ermittelt entsprechend EN 60745.

Oberächenschleifen:

Schwingungsemissionswert ah,SG

Unsicherheit K=

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

6,2 m/s2

1,5 m/s2

8,0 m/s2

1,5 m/s2

Schleifen mit Schleifblatt:

Schwingungsemissionswert ah,DS

Unsicherheit K=

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

6,0 m/s2

1,5 m/s2

7,5 m/s2

1,5 m/s2

Bei anderen Anwendungen, wie z.B. Trennschleifen oder Schleifen mit der Stahldrahtbürste können sich andere Vibrationswerte ergeben!

WARNUNG!

Der in diesen Anweisungen angegebene Schwingungspegel ist entsprechend einem in EN 60745 genormten Messverfahren gemessen

worden und kann für den Vergleich von Elektrowerkzeugen miteinander verwendet werden. Er eignet sich auch für eine vorläuge

Einschätzung der Schwingungsbelastung.

Der angegebene Schwingungspegel repräsentiert die hauptsächlichen Anwendungen des Elektrowerkzeugs. Wenn allerdings das

Elektrowerkzeug für andere Anwendungen, mit abweichenden Einsatzwerkzeugen oder ungenügender Wartung eingesetzt wird, kann

der Schwingungspegel abweichen. Dies kann die Schwingungsbelastung über den gesamten Arbeitszeitraum deutlich erhöhen.

Für eine genaue Abschätzung der Schwingungsbelastung sollten auch die Zeiten berücksichtigt werden, in denen das Gerät abgeschaltet

ist oder zwar läuft, aber nicht tatsächlich im Einsatz ist. Dies kann die Schwingungsbelastung über den gesamten Arbeitszeitraum

deutlich reduzieren.

Legen Sie zusätzliche Sicherheitsmaßnahmen zum Schutz des Bedieners vor der Wirkung von Schwingungen fest wie zum Beispiel:

Wartung von Elektrowerkzeug und Einsatzwerkzeugen, Warmhalten der Hände, Organisation der Arbeitsabläufe.

WARNUNG!

Lesen Sie alle Sicherheitshinweise und Anweisungen.

Versäumnisse bei der Einhaltung der Sicherheitshinweise und

Anweisungen können elektrischen Schlag, Brand und/oder schwere

Verletzungen verursachen.

Bewahren Sie alle Sicherheitshinweise und Anweisungen

für die Zukunft auf.

SICHERHEITSHINWEISE FÜR WINKELSCHLEIFER

Gemeinsame Sicherheitshinweise zum Schleifen,

Sandpapierschleifen, Arbeiten mit Drahtbürsten und

Trennschleifen:

a) Dieses Elektrowerkzeug ist zu verwenden als Schleifer,

Sandpapierschleifer, Drahtbürste und Trennschleifma-

schine. Beachten Sie alle Sicherheitshinweise, Anwei-

sungen, Darstellungen und Daten, die Sie mit dem Gerät

erhalten. Wenn Sie die folgenden Anweisungen nicht beachten,

kann es zu elektrischem Schlag, Feuer und/oder schweren Verlet-

zungen kommen.

b) Dieses Elektrowerkzeug ist nicht geeignet zum Polieren.

Verwendungen, für die das Elektrowerkzeug nicht vorgesehen ist,

können Gefährdungen und Verletzungen verursachen.

c) Verwenden Sie kein Zubehör, das vom Hersteller

nicht speziell für dieses Elektrowerkzeug vorgesehen

und empfohlen wurde. Nur weil Sie das Zubehör an Ihrem

https://manual-hub.com/

Stránka sa načítava...

AEG WS 10-115 Používateľská príručka

AEG WS 10-115 Používateľská príručka

v iných jazykoch

Ostatné dokumenty