Avent SCF356/00 Používateľská príručka

SCF356

Specications are subject to change without notice

4213 354 36716

1

2 3 4 5

6

7 8 9

10 11 12 13

14 15 16 17

18 19 20 21

22 23 24 25

26

27

SCF356

ENGLISH 6

БЪЛГАРСКИ 20

ČEŠTINA 35

EESTI 49

MAGYAR 63

ҚАЗАҚША 78

POLSKI 92

РУССКИЙ 108

6

General description (Fig. 1)

1. Baby bottle warmer

2. Progress indicator

3. Settings and on/o knob

4. Defrost setting

5. Milk warming setting 1

6. Milk warming setting 2

7. Milk warming setting 3

8. Baby food warming setting

9. On/o button

Important

To fully benet from the support that Philips

oers, register your appliance at

www.philips.com/welcome.

Read this user manual carefully before you

use the baby bottle warmer and save it for

future reference.

Danger

- Never immerse the appliance in water or

any other liquid, nor rinse it under the tap.

Warning

- Only use the appliance indoors.

- This appliances can be used by persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and

understand the hazards involved.

ENGLISH

- Cleaning and user maintenance shall not

be made by children.

- This appliance shall not be used by

children. Keep the appliance and its cord

out of reach of children.

- Children shall not play with the appliance.

- Do not immerse the cord, plug or

appliance in water or any other liquid.

- Do not let the mains cord hang over the

edge of a table or worktop. Excess cord

can be stored in the base of the baby

bottle warmer to ensure stability of the

appliance.

- Keep the mains cord away from hot

surfaces.

- Only connect the appliance to an earthed

wall socket. Always make sure that the

plug is inserted into the wall socket

properly.

- Check if the voltage indicated on the

bottom of the appliance corresponds to

the local mains voltage before you

connect the appliance.

- If you need to use an extension cord,

make sure it is an earthed extension cord

with a rating of at least 13 amperes.

ENGLISH 7

- Do not use the appliance if the plug, the

mains cord or the appliance itself is

damaged. If the mains cord is damaged,

you must have it replaced by Philips, a

service centre authorised by Philips or

similarly qualied persons in order to

avoid a hazard.

- Do not place the appliance on or near a

hot gas or electric cooker, or in a heated

oven.

- Do not preheat the appliance.

- Always place a fully assembled bottle

with cap in the baby bottle warmer before

you add water.

- Make sure you add water before you

switch on the baby bottle warmer.

- Hot water can cause serious burns. Be

careful when the baby bottle warmer

contains hot water.

- The accessible surfaces of the appliance

may become hot during use.

- Do not move the appliance when it

contains hot water.

- Always check the baby food temperature

before you feed your child.

ENGLISH8

Caution

- This appliance is intended to be used in

household and similar applications such

as farm houses, bed and breakfast type

environments, sta kitchen areas in

shops, oces and other working

environments, and by clients in hotels,

motels and other residential type

environments.

- Unplug the appliance when it is not in

use.

- Store any excess mains cord in the base

to ensure stability of the baby bottle

warmer.

- Let the appliance cool down before you

clean it.

- Follow the descaling instructions to avoid

irreparable damage.

- Do not try to open or repair the appliance

yourself. You can contact the Philips

Consumer Care Centre in your country

(see

www.philips.com/support).

- The food should not be heated for too

long.

- Only use the appliance as described in

the user manual to avoid potential injury

due to misuse.

ENGLISH 9

- The surface of the heating element is

subject to residual heat after use.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards

and regulations regarding exposure to electromagnetic elds.

Using the baby bottle warmer

With this baby bottle warmer, you can safely warm and

defrost milk in Philips Avent feeding bottles and milk or baby

food in containers.

The baby bottle warmer helps to preserve the valuable

nutrients and vitamins in breast milk because it never

overheats the milk. If milk becomes too warm, nutrients and

vitamins are damaged. To help preserve the quality of your

breast milk, it is important to heat the milk in a safe and

controlled way. The baby bottle warmer is designed to warm

gently and evenly and to avoid hot spots, as the milk

circulates during warming. The built-in sensor tracks and

controls the milk temperature, to avoid overheating at all

times.

Note: Philips Avent breast milk bags and Philips Avent

2oz/60ml bottles cannot be used in this baby bottle

warmer.

Explanation of settings

- You can choose between the following settings: (Fig. 2)

- Defrost setting: To defrost a bottle or container with frozen

milk or frozen baby food. No warming occurs.

- Milk warming settings: Select one of these settings when

you want to warm a bottle of milk to a safe temperature.

Setting 2 warms your milk to approximately body

temperature. Setting 1 warms your milk to a slightly lower

temperature and setting 3 warms your milk to a slightly

higher temperature.

ENGLISH10

- Baby food warming setting: Select this setting when you

want to warm a container or jar with baby food.

Using the baby bottle warmer to warm milk

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a bottle centrally in the baby bottle warmer (Fig. 4).

Note: To warm milk in a milk storage container, follow the

same steps as indicated for warming milk in a bottle.

3 Fill the baby bottle warmer with the same amount of

drinking water as the amount of milk you want to warm

up (for example, to warm up 125ml/4oz of milk, you need

to use 125ml/4oz of drinking water). If you want to heat

up a large amount of milk (>180ml/6oz), the maximum

water level is approximately 1cm/0.4 inches under the

rim of the baby bottle warmer (which corresponds to

adding 160ml/4.5oz of drinking water). An accurate water

level ensures correct warming performance. (Fig. 5)

4 Select the desired setting (Fig. 6).

Note: Experience teaches that babies may have a

preference for a specific milk temperature. This can be due

to personal preference or external factors (e.g. environment

temperature). All three settings ensure that the milk is

warmed to a safe temperature which is comfortable for your

child and helps to preserve the nutrients and vitamins in the

milk.

5 Press the on/o button to switch on the appliance. The

light in the button lights up to indicate that the baby

bottle warmer is on (Fig. 7).

Note: The baby bottle warmer starts warming up right after

you press the button.

6 The progress indicator starts to ll up gradually with

white light to show the progress of the milk warming

process (Fig. 8).

ENGLISH 11

Note: The progress indicator shows the progress of the milk

warming process. The progress indicator starts flashing

when the appliance is on. When the first warming phase has

been completed, the bottom segment lights up continuously

and the next segment starts flashing to show that the

second warming phase is in progress. These steps continue

until the third warming phase has been completed. Then the

entire progress indicator lights up continuously.

Note: During the warming process, the milk circulates to

ensure even warming. It takes about 10 minutes to warm

90ml/3oz of room-temperature milk. It takes slightly longer

to warm cold milk or a large amount of milk.

Caution: Do not take the bottle out of the baby bottle

warmer while the progress indicator is ashing.

7 When the entire progress indicator lights up

continuously, the milk has reached the set temperature.

- When the milk is warm, you can either take the bottle out

of the baby bottle warmer to feed your baby right away

(see section ‘Feeding your baby immediately’) or you can

keep it warm in the baby bottle warmer (see section

‘Keeping milk warm’).

Increasing the milk temperature

1 If you want the milk to be warmer, you can increase the

milk temperature gradually after it is ready by switching

to milk warming

setting 3 and leaving the bottle in the

appliance at the keep-warm mode

(Fig. 9).

2 If you just switched o the baby bottle warmer or if it just

switched o automatically, switch it back on without

removing the warm water from it, and follow the above

step (Fig. 10).

3 The baby bottle warmer switches o automatically after

20 minutes of keep-warm mode (Fig. 11).

ENGLISH12

Feeding your baby immediately

1 Press the on/o button to switch o the appliance and

take out the milk bottle (Fig. 10).

2 Always check the temperature of the milk before you feed

your baby. Gently swirl the milk in the bottle and check

the temperature of the milk by sprinkling a few drops on

the inside of your wrist (Fig. 12).

3 Unplug the appliance and empty the baby bottle

warmer (Fig. 13).

Keeping milk warm

1 When the milk has reached the desired temperature, the

baby bottle warmer automatically switches to the

keep-warm mode. In this mode, the milk is kept at the

set temperature for 20 minutes (Fig. 14).

2 The baby bottle warmer switches o automatically after

20 minutes. The progress indicator switches o to

indicate that the milk is not kept at the desired

temperature anymore (Fig. 11).

Note: If you want to feed your baby with milk at the set

temperature, you need to take the milk bottle out of the

baby bottle warmer and feed it to your baby right after the

baby bottle warmer switches o, otherwise the milk cools

down.

Note: You cannot prolong the keep-warm mode of the baby

bottle warmer for more than 20 minutes.

Caution: It is not recommended to reheat breast milk twice,

as bacteria start to develop in the milk.

3 Always check the temperature of the milk before you

feed your baby. Gently swirl the milk in the bottle or milk

storage container and check the temperature of the milk

by sprinkling a few drops on the inside of your

wrist (Fig. 12).

4 Unplug the appliance and empty the baby bottle

warmer (Fig. 13).

ENGLISH 13

Re-using the baby bottle warmer right away for another

bottle

If you want to heat up another bottle right away, let the baby

bottle warmer cool down for a few minutes. To speed up this

process, ll the baby bottle warmer with fresh cold water.

When you switch on the baby bottle warmer, the progress

indicator starts ashing from bottom to top to indicate that

the appliance is heating up again.

Note: If the progress indicator is on but does not flash, the

baby bottle warmer is still too warm to heat up another

bottle. Please switch o the baby bottle warmer, let it cool

down for a few minutes and make sure you fill it with fresh

cold water.

Using the baby bottle warmer to warm baby food

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a baby food container or jar centrally in the baby

bottle warmer (Fig. 15).

Note: You can leave o the lid of the food container or jar,

so you can stir the baby food during heating.

3 Fill the baby bottle warmer with the same amount of

drinking water as the amount of baby food you want to

warm up (for example, to warm up 125ml/4oz of baby

food, you need to use 125ml/4oz of drinking water). If

you want to warm up a large amount of baby food, the

maximum water level is approximately 1cm/0.4 inches

under the rim of the baby bottle warmer (which

corresponds to adding 160ml/4.5oz of drinking water).

An accurate water level ensures correct warming

performance. (Fig. 16)

4 Select the baby food warming setting (Fig. 17).

5 Press the on/o button to switch on the appliance. The

light in the progress indicator shows that the baby bottle

warmer is on (Fig. 18).

ENGLISH14

Note: The baby bottle warmer starts warming up right after

you press the button. Due to the large variety of baby food

consistencies, it is not possible for the appliance to detect

exactly how long the baby food should be warmed.

6 The progress indicator starts to ll gradually with white

light to show the progress of the warming process. During

the warming process, do not take the jar or container out

of the baby bottle warmer but stir the baby food while

the jar or container is still in the baby bottle

warmer (Fig. 19).

Note: You can start stirring the baby food once the second

segment of the progress indicator lights up continuously.

Stirring before this moment is not eective as the

temperature of the baby food is still too low.

Caution: Do not take the food container or jar out of the

baby bottle warmer during warming.

7 When the entire progress indicator lights up

continuously, the baby food has reached the desired

temperature.

Note: Due to the large variety of baby food consistencies, it

is strongly recommended that you continuously stir the

baby food and check its temperature while it is heating up

for an optimal result.

- When the baby food is warm, you can either take the baby

food container or jar out of the baby bottle warmer to feed

your baby right away (see section ‘Feeding your baby

immediately’) or you can keep it warm in the baby bottle

warmer (see section ‘Keeping baby food warm’).

Increasing the baby food temperature

1 Always taste the baby food after warming it up to make

sure it is not too hot. If you want the baby food to be

warmer, put the container back into the baby bottle

warmer and leave it in there at the keep warm-mode for

some time. Keep stirring the baby food (Fig. 15).

ENGLISH 15

2 If you just switched o the baby bottle warmer or if it just

switched o automatically, switch it back on without

removing the warm water from it, and follow the above

step (Fig. 18).

3 The baby bottle warmer switches o automatically after

20 minutes of keep-warm mode (Fig. 20).

Feeding your baby immediately

1 Press the on/o button to switch o the appliance and

take out the baby food container or jar (Fig. 18).

2 After warming, taste the baby food to ensure it is not too

hot (Fig. 21).

3 Unplug the appliance and empty the baby bottle

warmer (Fig. 13).

Keeping baby food warm

1 When the baby food has reached the desired

temperature, the baby bottle warmer automatically

switches to the keep-warm mode. In this mode, the baby

food is kept at the desired temperature for 20

minutes (Fig. 22).

2 The baby bottle warmer switches o automatically after

20 minutes. The progress indicator switches o to

indicate that the baby food is not kept at the desired

temperature anymore (Fig. 20).

Note: If you want to feed your baby with the baby food at

the set temperature, you need to take the baby food out of

the baby bottle warmer and feed it to your baby right after

the baby bottle warmer switches o. If you do not do this,

the baby food slowly cools down.

Note: You cannot prolong the keep-warm mode of the baby

bottle warmer for more than 20 minutes.

3 Always check the temperature of the baby food before

you feed your baby. Gently stir the baby food in the baby

food container or jar and taste the baby food to ensure it

is not too hot (Fig. 21).

ENGLISH16

4 Unplug the appliance and empty the baby bottle

warmer (Fig. 13).

Re-using the baby bottle warmer right away for another

container of baby food

If you want to heat up another container or jar with baby food

right away, let the baby bottle warmer cool down for a few

minutes. To speed up this process, ll the baby bottle warmer

with fresh cold water. When you switch on the baby bottle

warmer, the progress indicator starts ashing from bottom to

top to indicate that the appliance is heating up again.

Note: If the progress indicator is on but does not flash, the

baby bottle warmer is still too warm to heat up another

container or jar with baby food. Please switch o the baby

bottle warmer, let it cool down for a few minutes and make

sure you fill it with fresh cold water.

Defrost setting

At this setting, you can defrost frozen milk or baby food.

Follow the steps indicated in sections ‘Using the baby bottle

warmer to warm milk’ or ‘Using the baby bottle warmer to

warm baby food’.

The progress indicator starts ashing when the appliance is

on the defrost setting. The progress indicator gradually lls

with white light to show the progress of the defrosting

process. The milk or baby food has defrosted completely

when the entire progress indicator lights up continuously.

The defrost setting defrosts the milk or baby food but does

not warm it up. If you want to warm up milk or baby food after

defrosting it, rst switch o the appliance, then select the

desired warming setting and switch the appliance back on.

ENGLISH 17

18

Cleaning and descaling

Cleaning

1 After each use, unplug the baby bottle warmer and let it

cool down (Fig. 23).

2 Remove the water from the baby bottle warmer for

hygienic reasons (Fig. 24).

3 Wipe the outside and inside of the baby bottle warmer

with a moist cloth (Fig. 25).

Do not use abrasive, anti-bacterial cleaning agents,

chemical solvents or sharp tools to clean the baby bottle

warmer.

Note: If you used the baby bottle warmer to warm

containers with baby food, make sure that no spilled baby

food remains on the bottom of the baby bottle warmer.

Descaling

It is recommended to descale the baby bottle warmer every

four weeks to ensure it continues to work eciently.

1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold

water to descale the baby bottle warmer. First select the

defrost setting, then switch on the baby bottle warmer

and let the appliance operate for 10 minutes. Leave the

solution in the baby bottle warmer until all scale has

dissolved. (Fig. 26)

Note: You can also use citric acid based descalers.

Note: Do not use other types of descalers.

2 Unplug the baby bottle warmer before you empty

it (Fig. 23).

3 Empty the baby bottle warmer and rinse its inside

thoroughly. If you still see traces of scale after rinsing,

repeat the descaling procedure (Fig. 24).

ENGLISH18

19

Recycling

- This symbol means that this product shall not be disposed

of with normal household waste (2012/19/EU). (Fig. 27)

- Follow your country’s rules for the separate collection of

electrical and electronic products. Correct disposal helps

prevent negative consequences for the environment and

human health.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide

guarantee leaet.

ENGLISH 19

Общо описание (фиг. 1)

1. Подгревател за бебешка бутилка

2. Индикатор за напредъка

3. Настройки и бутон за вкл./изкл.

4. Настройка за размразяване

5. Настройка за затопляне на мляко 1

6. Настройка за затопляне на мляко 2

7. Настройка за затопляне на мляко 3

8. Настройка за затопляне на бебешка храна

9. Бутон за вкл./изкл.

Важно

За да се възползвате изцяло от предлаганата от

Philips поддръжка, регистрирайте уреда си на

адрес www.philips.bg/welcome.

Преди да използвате подгревателя за бебешка

бутилка, прочетете внимателно това ръководство

за потребителя и го запазете за бъдещи справки.

Опасност

- Никога не потапяйте задвижващия блок

във вода или друга течност и не го мийте с

течаща вода.

Предупреждение

- Използвайте уреда само на закрито.

- Този уред може да се използва от хора с

намалени физически, сетивни или умствени

възможности или без опит и познания, ако са

под наблюдение или са инструктирани за

безопасната употреба на уреда и са разбрали

евентуалните опасности.

БЪЛГАРСКИ20

21

- Не позволявайте на деца да извършват

почистване или поддръжка на уреда.

- Този уред не бива да се използва от деца.

Пазете уреда и кабела далече от достъп на

деца.

- Не позволявайте на деца да си играят с уреда.

- Не потапяйте кабела, щепсела или уреда във

вода или в друга течност.

- Не оставяйте захранващия кабел да виси през

ръба на масата или на работния плот.

Излишната дължина на кабела може да се

прибере в основата на подгревателя за

бебешка бутилка, което осигурява стабилност

на уреда.

- Внимавайте кабелът да е далече от горещи

повърхности.

- Включвайте уреда само в заземен контакт.

Винаги проверявайте дали щепселът е включен

в контакта както трябва.

- Преди да включите уреда в контакта,

проверете дали напрежението, посочено на

дъното на уреда, отговаря на това на местната

електрическа мрежа.

- Ако се налага да използвате удължителен

кабел, уверете се, че той е заземен с

номинален ток от най-малко 13 ампера.

- Не използвайте уреда, ако щепселът,

захранващият кабел или самият уред е

БЪЛГАРСКИ

повреден. С оглед предотвратяване на

опасност при повреда в захранващия кабел

той трябва да бъде сменен от Philips,

оторизиран от Philips сервиз или квалифициран

техник.

- Не поставяйте уреда върху или в близост до

горещ газов или електрически котлон или в

загрята фурна.

- Не затопляйте предварително уреда.

- Винаги поставяйте напълно сглобена бутилка с

капачка в подгревателя за бебешка бутилка,

преди да добавите вода.

- Уверете се, че сте добавили вода, преди да

включите подгревателя за бебешка бутилка.

- Горещата вода може да причини тежки

изгаряния. Внимавайте, когато подгревателят

за бебешка бутилка съдържа гореща вода.

- Достъпните повърхности на уреда може да се

нагорещяват при употреба.

- Не местете уреда, когато съдържа гореща

вода.

- Винаги проверявайте температурата на

храната, преди да пристъпите към хранене на

детето.

Внимание

- Този уред е предназначен за използване за

домакински и подобни цели, например във

ферми, в места за нощуване и закуска, в

БЪЛГАРСКИ22

Stránka sa načítava ...

Avent SCF356/00 Používateľská príručka

Avent SCF356/00 Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty