Fieldmann FZP 4516 B Používateľská príručka

FZP 4516 B

EN

2

FZP 4516 B

English .................................................................................................................................................................................3–26

Čeština .............................................................................................................................................................................27–50

Slovenčina ......................................................................................................................................................................51–74

Magyarul ........................................................................................................................................................................75–98

Polski ...............................................................................................................................................................................99–122

Slovenščina ...............................................................................................................................................................123–148

EN

CHAIN SAW USER'S MANUAL

3

Table of Contents

Chain saw

USER'S MANUAL

Thank you for purchasing this chain saw. Before you start using it, please, carefully read

this user's manual and save it for possible future use.

CONTENTS

1. GENERAL SAFETY INSTRUCTIONS ........................................................................................................................5

Important safety information .................................................................................................................................5

Packaging .......................................................................................................................................................................5

User's Manual .................................................................................................................................................................5

2. EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE ................................................................6

3. SAFETY INSTRUCTIONS ...............................................................................................................................................7

Before using the power tool ...................................................................................................................................7

Safety of the operator, work equipment and clothing ...........................................................................7

Instructions for handling fuel ..................................................................................................................................9

4. DESCRIPTION OF THE POWER TOOL AND INCLUDED CONTENTS ...................................................10

Description of the power tool (see Fig. 1) .....................................................................................................10

5. INSTALLING THE BUMPER SPIKES, GUIDE BAR AND CHAIN ................................................................. 11

Installing the bumper spikes ................................................................................................................................ 11

Installing the guide bar and chain .................................................................................................................. 11

6. FUEL AND CHAIN LUBRICATING OIL ................................................................................................................12

Filling the oil tank ........................................................................................................................................................12

Mixing the fuel mix ...................................................................................................................................................12

Storing fuel .....................................................................................................................................................................13

7. PREPARING FOR OPERATION ..............................................................................................................................13

Chain brake (Fig. 1, point 9) .................................................................................................................................14

Checking the working order of the brake ....................................................................................................14

8. TURNING THE CHAIN SAW ON AND OFF ......................................................................................................14

Starting a cold engine ............................................................................................................................................14

Starting a warm engine ..........................................................................................................................................15

Speed control system ..............................................................................................................................................15

Stopping the engine ................................................................................................................................................15

Checking chain lubrication .................................................................................................................................15

9. ADJUSTING THE CHAIN TENSION .......................................................................................................................16

10. CUTTING ..........................................................................................................................................................................16

Safety brake (protection against kickback) ...............................................................................................16

Felling trees ....................................................................................................................................................................17

Cutting logs ...................................................................................................................................................................17

Log lying on the ground ....................................................................................................................................17

Log above the ground .......................................................................................................................................18

Lopping a fallen tree ...............................................................................................................................................18

EN 4

FZP 4516 B

Table of Contents

11. CLEANING AND MAINTENANCE .......................................................................................................................18

Maintenance after every use .............................................................................................................................18

Cleaning the body of the chain saw ..............................................................................................................18

Maintaining the guide bar ...................................................................................................................................19

Normal maintenance of the guide bar ........................................................................................................19

12. SHARPENING THE SAW CHAIN ...........................................................................................................................20

Equipment necessary for sharpening a saw chain ................................................................................20

Sharpening the teeth on the chain .................................................................................................................20

Filing the depth gauge ...........................................................................................................................................21

13. REPLACING THE SAW CHAIN ...............................................................................................................................22

14. TECHNICAL SPECIFICATIONS ...............................................................................................................................23

15. DISPOSAL ........................................................................................................................................................................24

16. DECLARATION OF CONFORMITY ......................................................................................................................25

EN

CHAIN SAW USER'S MANUAL

5

General safety instructions

1. GENERAL SAFETY INSTRUCTIONS

Important safety notice

Carefully unpack the product and take care not to throw away any part of the packaging before you ﬁ nd all

the parts of the product.

Store the product in a dry place out of reach of children.

Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical

shock, a ﬁ re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so

can be handed over for recycling.

User’s manual

Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself

with the operating elements and the correct use of the machine. Keep the user’s manual in a safe place where

it can be easily retrieved for future use. Save the original packaging, including the internal packing material,

warranty card and proof of purchase receipt at least for the duration of the warranty.

If you need to ship this machine, pack it in the original cardboard box to ensure maximum protection during

shipping or transport (e.g. when moving or when you need to send this product for repair).

NOTE: If you hand over the power tool to somebody else, do so together with this user’s manual.

Following the instructions in the included user’s manual is a prerequisite for the proper use of the power tool.

The user’s manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not

following the instructions in this manual.

EN 6

FZP 4516 B

Explanation of instruction labels on the machine

2. EXPLANATION OF INSTRUCTION LABELS ON

THE MACHINE

Before using the power tool, carefully read

the user's manual.

When operating the power tool, wear

protective aids such as safety glasses,

earmuffs, etc.

Always use two hands when operating

the chain saw.

While working use protective gloves.

Use solid insulating work footwear.

Attention! Danger of kickback

Warning! Attention!

EN

CHAIN SAW USER'S MANUAL

7

Safety Instructions

3. SAFETY INSTRUCTIONS

ATTENTION! The safety instructions in this user’s manual are marked with the symbol containing critical

points, which one needs to pay attention to when operating the power tool to prevent serious or fatal injuries.

Please carefully study the instructions and adhere to them.

ATTENTION! This symbol indicates instructions that must be adhered to in order to prevent accidents that

could result in serious or fatal injuries.

NOTE: This symbol indicates a tip or instructions useful when operating the power tool.

Before using the power tool

Before using the power tool, carefully read the user’s manual.

Do not use the power tool if your are under the inﬂ uence of alcohol or narcotics, if you are tired or exhausted.

Do not use the power tool if your are taking medication, which could affect or limit your decision-making

abilities for safe operation of the power tool.

Do not use the power tool indoors, the emitted gases contain damaging carbon monoxide.

Never use the power tool under the conditions listed below:

– If the work surface is slippery or if weather conditions do not permit you to maintain a stable stance while

operating the power tool.

– If it is dark, heavy fog or under poor weather conditions, which limit visibility of the work area.

– During rain, during a storm or in strong winds or under conditions that could be dangerous when

operating the power tool.

If you are using the chain saw for the ﬁ rst time, please consult with an experienced user before starting work.

Tiredness or physical exhaustion may lead to inattentiveness, which may result in serious injury

Limit the operating time of the power tool to approx. 10 minutes per single use and try to rest for

approximately 10-20 minutes between work sessions. Limit the total amount of work per day to

approximately 2 hours.

Make sure that you have the user’s manual at hand in case you need to use it.

If you sell, loan or handover the power tool, make sure that you include the user’s manual.

Never allow children or other persons that are insufﬁ ciently acquainted with the user’s manual to use this

power tool.

Safety of the operator, work equipment and clothing

When operating a chain saw, you should wear the following work clothing and protective aids:

– Helmet

– Safety glasses or protective face shield

– Work gloves

– Anti-slip work boots

– Earmuffs

EN 8

FZP 4516 B

Safety Instructions

Furthermore, you should also have

– The included tools

– Sufﬁ cient supply of fuel and chain lubricating oil

– Accessories for designating the work area (rope, warning signs)

– Whistle (to call for help)

– Hand saw or axe (to remove potential obstacles)

When working, never wear loose clothing, jewellery, that could become caught by the chain saw. Do not

wear sandals when working, do not work barefoot.

Check the work area, the item being cut and the cutting direction. Remove obstacles.

Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not

have a planned escape route in the event of a falling tree.

Pay increased attention and keep passers-by and pets away from the work area at a distance of at least

2.5 times the length of the item being cut.

Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged,

incorrectly adjusted or incomplete. Check that the chain stops turning when the throttle trigger is released.

Keep the handles dry, clean and free of oil and fuel stains.

Do not touch the mufﬂ er, spark plugs or other metal parts of the engine when the power tool is running or

immediately after it is turned off - there is a risk of burns or injury by electrical shock.

Pay exceptional attention when cutting thin branches or trunks because fragile material may become caught

in the chain and ﬂ ung towards the operator and may thus cause a loss of balance.

When cutting tensioned branches keep in mind that they will ﬂ ing out when the wood ﬁ bres are cut and the

tension is released.

Check for and remove dry branches that could come loose from the falling tree.

Make sure that the power tool is turned off when you put it down.

CAUTION danger of kickback! Kickback may occur when the nose of the guide bar comes into

contact with an item or if the material being cut clamps the chain in the cut. During contact with the item,

the chain saw may be ﬂ ung with the guide bar moving up and back towards the operator. A clamped chain

may result in a fast backward movement of the guide bar towards the operator. Both these reactions may

lead to a loss of control over the chain saw and subsequent serious injuries. Do not rely only on the chain

saw’s safety features. As the operator of the chain saw, you must constantly adhere to multiple rules to avoid

injuries or damages.

If you are acquainted with the kickback principle, you can reduce or eliminate the moment of surprise.

Unexpected reactions result in accidents.

If the engine is running, hold the chain saw with both hands with the right hand on the rear handle and the

left hand on the front handle. Firmly grasp the handle with the thumb going around towards the ﬁ ngers.

A ﬁ rm grip helps limit kickback and to keep the chain saw under control.

There must be no obstacles in the work area. When working with the chain saw, the loose end of the guide

bar must not touch a branch, trunk or another obstacle.

Cut with the engine running at high speed.

A stable stance must be maintained at all times when cutting, do not cut above shoulder height.

Adhere to the instructions of the manufacturer for lubricating and sharpening the chain.

Only use spare chains and guide bars speciﬁ ed by the manufacturer or their equivalents.

EN

CHAIN SAW USER'S MANUAL

9

Safety Instructions

Instructions for handling fuel

The engine of the power tool is designed to use a highly ﬂ ammable fuel mix. Never store fuel containers or reﬁ ll

fuel in the vicinity of an open ﬂ ame, wood stove, electrical lines, welding work or other sources of heat or ﬂ ame,

which could lead to ignition.

Smoking is forbidden when operating the power tool and when reﬁ lling fuel.

When reﬁ lling fuel, make sure that the power tool is off and that there is no open ﬂ ame in the vicinity.

If the power tool is sprayed with fuel, use a dry cloth to wipe away the stains.

After reﬁ lling fuel, screw on the fuel tank cap and take the power tool at least 3 m away from the place where

it was reﬁ lled and then start it up.

EN 10

FZP 4516 B

Machine description and included contents

Description of the power tool (see Fig. 1)

1. Throttle safety switch

2. Throttle trigger

3. Main power switch

4. Fuel tank cap

5. Oil tank cap

6. Front handle

7. Chain

8. Guide bar

9. Safety brake

10. Starting handle

11. Air ﬁ lter cover screw

12. Choke lever

13. Throttle trigger lock

Included contents: Petrol chain saw, 405 mm guide bar, Oregon chain, plastic guide bar cover, calibrated fuel

mixing container, spare spark plug, tool set with ﬁ le.

4. MACHINE DESCRIPTION AND INCLUDED

CONTENTS

Fig. 1

1

12

11

10

9

8765 43

2

13

EN

CHAIN SAW USER'S MANUAL

11

Installing the bumper spikes, guide bar and chain

5. INSTALLING THE BUMPER SPIKES,

GUIDE BAR AND CHAIN

ATTENTION! Always wear protective gloves

when installing and inspecting the chain to prevent

injury from the sharp cutting edges on the chain.

Installing the bumper spikes

Using the included hex key and screws, attach the

bumper spikes, see picture (Fig. 2).

Installing the guide bar and chain

The safety brake lever (Fig. 1 point 9) must be

disengaged (pull it towards the top handle)

Loosen two nuts and take off the sprocket cover

(Fig. 3, point 1).

Seat the chain on to the guide bar and then thread

on to the sprocket (pinion). At the same time, hold

the chain on the guide bar.

ATTENTION! The chain tensioning pin

(Fig. 3, point 2) must ﬁ t into the hole in the guide

bar (Fig. 3, point 3). The position of this pin can be

adjusted using the chain tensioning screw (Fig. 5)

ATTENTION! Ensure that the chain is always

correctly ﬁ tted in the sprocket ring (Fig. 4). If this is

not the case, the chain saw may be damaged.

Put the sprocket cover back. Do not fully tighten the

screws, tighten by hand only, to make it possible to

tension the chain.

Tension the chain using the tensioning screw

(Fig. 5) and then tighten the sprocket cover nuts

using the included tubular wrench

ATTENTION! The chain is correctly tensioned if

it is possible to lift chain off the guide bar and its

height in the horizontal position in the middle of the

guide bar is 3 to 4 mm.

Fig. 2

Fig. 3

12

3

Fig. 5

Fig. 4

EN 12

FZP 4516 B

Fuel and chain lubricating oil

6. FUEL AND CHAIN LUBRICATING OIL

Filling the oil tank

ATTENTION! A new chain requires a certain running-in period, which is usually 5 minutes. The lubrication

of the chain is very important during this phase. After this running-in period, check the chain tension and

readjust if necessary.

The oil tank on the supplied chain saw is empty. Fill this oil tank with oil prior to ﬁ rst use of this chain saw.

Only use oil speciﬁ ed for total-loss lubrication

Screw off the oil tank cap (Fig. 6, point 1).

Pour the oil into the tank (take care to prevent the oil from becoming dirty while ﬁ lling the tank).

Screw on the oil tank cap

ATTENTION! Do not use oil that has already been used or processed because this could damage the oil

pump.

Mixing the fuel mix

ATTENTION! Never pour fuel into the fuel tank in a closed and unventilated location.

ATTENTION! Do not pour fuel in the vicinity of an open ﬂ ame or a source of sparks.

ATTENTION! Do not overﬁ ll the petrol tank. Before starting the engine, make sure that all spilt fuel is wiped

away.

ATTENTION! If the engine is hot, DO NOT POUR IN FUEL.

For this type of two-stroke engine a mixture of lead-free petrol and two-stroke engine oil is used at a ratio of

25 : 1.

ATTENTION! A fuel mix that is mixed at a ratio other than 25 : 1 may damage the engine. Make sure that

this fuel mix is mixed correctly.

When mixing petrol with two-stroke engine oil, use only petrol containing NO ETHANOL or METHANOL (types

of alcohols).

Use quality petrol with an octane number of 95 or higher. This will help prevent possible damage to the fuel

system and other parts of the engine.

We recommend the use of the calibrated container supplied with the chain saw for mixing the fuel mix.

DO NOT MIX THE PETROL AND OIL DIRECTLY IN THE FUEL TANK.

Screw off the fuel tank cap (Fig. 6, point 2) and pour in the fuel. Then screw the cap back on.

EN

CHAIN SAW USER'S MANUAL

13

Fuel and chain lubricating oil | Preparing for operation

Storing fuel

Only store fuel in a clean, safe and approved canister.

Inform yourself about and adhere to local directives

related to the type and storage of canisters ﬁ lled with

fuel.

ATTENTION! Fuel for two-stroke engines may

separate. Prior to every use, thoroughly shake the

canister with fuel.

ATTENTION! Stored fuel ages. Do not mix more

fuel than you expect to consume within one month.

7. PREPARING FOR OPERATION

IMPORTANT: Follow instructions for preparing the fuel mix! Not following these instruction may damage

the engine! Do not use fuel that has been stored for longer than two months. A fuel mix stored for longer than

two months will cause problems at start up and lower engine performance. If the fuel mix is stored for longer

than two months, it should be removed and new fuel must be used.

Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged,

incorrectly adjusted or incomplete.

Check whether any screws, nuts and installation elements are loose. Tighten any loose screws.

Check whether the air ﬁ lter is dirty. Prior to starting work, remove all dirt from the air ﬁ lter.

Check that the chain is tensioned. You can lift a correctly tensioned chain in the middle of the guide bar in the

horizontal position by 3 to 4 mm

Keep the handles dry, clean and free of oil and fuel stains.

Check the fuel tank for leaks.

Check the work area, the item being cut and the cutting direction. Remove obstacles.

Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not

have a planned escape route in the event of a falling tree.

Pay increased attention and keep passers-by and pets away from the work area at a distance of at

least 2.5 times the length of the item being cut.

Fig. 6

21

EN 14

FZP 4516 B

Preparing for operation | Turning the chain saw on and off

Chain brake (Fig. 1, point 9)

This chain saw is equipped with an automatic brake that stops the chain in the event of kickback. The brake is

engaged automatically by inertia acting on the ballast located under the rear cover. This brake can be operated

manually by tilting down the front protective frame towards the guide bar.

The brake is disengaged by pulling the front protective frame back towards the chain saw handle.

ATTENTION! Before every use, check that the chain brake is in working order in the following manner.

Checking the working order of the brake

Place the running chain saw on to the ground and for 1 to 2 seconds leave it at full speed.

Push the brake lever (Fig. 1, point 9) forward. The chain should stop immediately.

ATTENTION! If the chain stops slowly or does not stop at all, do not use the chain saw and contact an

authorised service centre.

If you wish to disengage the brake, pull the brake lever towards the top handle so that you hear the typical click.

ATTENTION! Check that the chain brake is in order. A correctly functioning chain brake will protect you

against potential injury, which could result from kickback.

If the brake is not working properly, have it adjusted or repaired at an authorised service centre.

8. TURNING THE CHAIN SAW ON AND OFF

WARNING

Prior to starting the engine, make sure that the chain moves freely along the guide bar and is not touching

any foreign objects.

When the engine is idling, the saw chain must not be turning. Otherwise, contact an authorised service

centre to perform an inspection and remedy the problem.

Prior to starting the engine, make sure that the throttle trigger moves freely.

ATTENTION: Exposure to vibrations may damage the health of persons that suffer from circulatory or

nerve system problems. If any physical problems become evident, such as desensitisation, loss of sensitivity,

loss of usual strength or changes in skin colour, please contact a doctor. These systems usually manifest

themselves on ﬁ ngers, hands or wrists.

Starting a cold engine

1. Set the main power switch to the top position (see Fig. 7, point 1)

2. Pull out the choke lever (Fig. 7, point 2) but do not touch the throttle trigger.

3. Place the chain saw ﬂ at on the ground so that it is stable and pull on the handle of the starting cord until the

engine rotates (the engine will show signs of attempting to start) (Fig. 8).

4. At this point, push the choke lever back in (Fig. 7, point 2) and start the engine by repeatedly pulling on the

starting cord.

EN

CHAIN SAW USER'S MANUAL

15

ATTENTION! Spinning the engine for too long

with the choke lever pulled out will result in ﬂ ooding

of the engine and problems with starting it up.

5. Prior to starting work, leave the engine to warm

up for a few minutes to get up to operating

temperature.

Starting a warm engine

1. Set the main power switch to the top position

(see Fig. 7, point 1)

2. Pull on the handle of the starting cord until the

engine starts up (Fig. 8)

DO NOT USE THE CHOKE!

ATTENTION! In the event that the fuel in the fuel

tank was completely used up, after pouring in fuel,

repeat the steps for STARTING A COLD ENGINE.

Speed control

To increase speed, ﬁ rst use the palm of your hand

to push down the throttle safety switch

(Fig. 7, point 4) and then use your ﬁ nger to

pull on the throttle trigger (Fig. 7, point 5)

To lower the speed, release the throttle trigger

Stopping the engine

Release the throttle trigger (Fig. 7, point 5) and switch the main power switch to the "Stop" position

(Fig. 1, point 1).

WARNING

The engine exhaust fumes contain chemical substances that are damaging to health. Never inhale these

fumes. Always start the chain saw outdoors.

Checking chain lubrication

ATTENTION! Adhere to safety provisions and

prevent the guide bar from coming into contact

with the surface of the terrain. Use this power tool

safely and maintain a minimum distance of 20 cm

from the ground.

Before starting work, check the chain lubrication

and the amount of oil in the oil tank. Start the

chain saw and hold it above the ground. If you see

Fig. 7

2

3

4

1

5

Fig. 8

Fig. 9

Turning the chain saw on and off

EN 16

FZP 4516 B

a growing oil stain then chain lubrication is working properly. If there are no oil stains on the ground, adjust

the lubrication strength on the underside of the chain saw (Fig. 9)

If even then, the chain is not sufﬁ ciently lubricated, clean out the oil outlet (under the sprocket cover), the top

chain tensioning hole and the oil lines, or contact an authorised service centre if necessary.

9. ADJUSTING THE CHAIN TENSION

ATTENTION! Due to the effect of higher temperatures, during operation the saw chain has a tendency to

lengthen. A longer chain becomes loose and could slide off the guide bar.

Loosen the sprocket cover fastening nuts.

Make sure that the chain is seated in the guiding groove of the guide bar.

Use a screwdriver to turn the chain tensioning screw (Fig. 5). Turn the tensioning screw until the required

tension is achieved (you should lift the chain in the middle of the guide bar in the horizontal position to

a height of 3 to 4 mm).

Firmly tighten the guide bar fastening nuts.

ATTENTION! Do not tension the chain excessively. Excessive tension of a warm chain may result in

excessively tension when it cools down.

10. CUTTING

ATTENTION! Before proceeding, please read the chapter “Safety instructions”. We recommend that you

gain experience by cutting smaller logs. In this way you will also get to know the chain saw.

Always adhere to safety instructions. The chain saw may only be used for cutting wood.

It is forbidden to cut any other materials. Vibrations and kickback differ for various materials. Do not use the

chain saw as a lever for lifting, moving or splitting material. It is forbidden to attach any parts or jigs other

than those speciﬁ ed in the technical documentation.

It is not necessary to push the chain saw into the cut. When the engine is running at full speed, push the

chain saw down lightly.

If the chain jams in the cut, do not attempt to free it by pulling, rather stretch open the cut using a wedge or

crowbar.

Safety brake (protection against kickback)

This chain saw is equipped with an automatic chain brake that, if it works correctly, immediately stops the

chain in the event of kickback. It is necessary to check the working order of the chain brake before every use

of the chain saw. Run the chainsaw at full speed for 1 - 2 seconds and then tilt the front protective cover.

The chain must stop immediately even when the engine is running at high speed. If the chain stops slowly

or does not stop at all, please contact an authorised service centre.

Turning the chain saw on and off | Adjusting the chain tension | Cutting

EN

CHAIN SAW USER'S MANUAL

17

Cutting

It is extremely important to check the working order of the chain brake and the sharpness of the chain before

every use to ensure that the necessary level of safety in the event of a kickback is maintained. Removing

safety accessories, incorrect maintenance or when using unsuitable guide bars or chains may, in the event

of kickback, result in serious injuries.

Felling trees

Decide about the direction in which the tree will fall,

respecting the wind direction, incline angle of the

tree and location of the branches, and consider all

other factors before cutting.

The area around the tree must be clear, without

obstacles, and must enable a stable stance. The

escape route must be passable.

Cut a wedge into one third of the tree’s diameter on

the side to which the tree should fall.

(see Fig. Felling, point 1)

From the opposite direction perform a separation

cut at a level above the wedge cut. (see Fig. Felling, point 2)

The tree will fall in the direction towards the wedge cut. (see Fig. Felling, point 3)

ATTENTION! When felling trees, inform other people in the area about the potential danger.

Felling trees requires experience and we do not recommend performing this task without the necessary

experience.

Cutting logs

ATTENTION! Always maintain a stable stance. Do not step on logs.

ATTENTION! Before starting work, check that all components are in their place and that all nuts and bolts

are tightened.

The log being cut may roll away. Especially when cutting on a slope, always stand above the log being cut.

Prevent kickback of the saw by following the instructions in chapter “Safety instructions”.

Before starting work, assess the direction of the force causing the cut trunk to bend. The ﬁ nal cut needs to

always be done from the opposite side of where the bending force is acting to prevent the guide bar from

being clamped inside the cut.

Only carry the chain saw with the engine turned off and the guide bar protected by the protective cover.

Log lying on the ground

Cut it halfway through, then roll it over and

complete the cut from the other side.

Fig. Cutting trees

3

2

1

EN 18

FZP 4516 B

Cutting | Cleaning and maintenance

Log above the ground

In part “A” make a cut from below to a third of the

log and then complete the cut from above. In part

“B” make a cut from above to a third of the log and

then complete the cut from below.

Removing a fallen tree

First ﬁ nd out to which side the branch is bent. Then

make the initial cut from the side of the bend and

then complete the cut from the opposite side.

ATTENTION! A bent branch may spring up.

11. CLEANING AND MAINTENANCE

ATTENTION! Prior to cleaning, inspecting or repairing the chain saw, its engine must be turned off and

cold and the spark plug must be removed to prevent accidentally starting the engine.

Maintenance after every use

Remove the guide bar and use a brush to clean away accumulated sawdust from the entire chain saw. Use

a spatula or screwdriver to remove stubborn dirt.

Air ﬁ lter:

Loosen the screw (Fig 1, point 11) and remove the air ﬁ lter cover. Take out the ﬁ lter insert and use a brush to

remove the dust. If the ﬁ lter insert is clogged with dust, dismantle into 2 parts and wash it out in petrol. If you

are using compressed air, blow from the inside out.

Lubricating hole:

Take off the guide bar and check the passage of the lubricating hole.

Guide bar:

After taking off the guide bar, remove dust from the grooves and the lubricating hole.

Other parts:

Check for any oil leaks, loose mounts and damaged main parts, particularly in the location where the handles

and the guide bar are mounted. Any identiﬁ ed defects must be repaired before the chain saw is used again.

Cleaning the body of the chain saw

Keep the body of the chain saw clean. When cleaning, use a soft cloth dipped in a soap solution. Use this cloth to

meticulously clean the body of the chain saw.

AB

1

2

1

2

1

EN

CHAIN SAW USER'S MANUAL

19

Cleaning and maintenance

Maintaining the guide bar

Most problems with the guide bar arise due to

uneven wear.

Uneven wear occurs mainly as a result of an

incorrectly sharpened chain or an incorrectly set

depth gauge.

When the guide bar is worn out unevenly, the

guiding groove is widened (see Picture). The result

is a rattling chain and rivets falling off. The chain

saw cannot be used for straight cuts. In such

a case, replace the guide bar for a new one.

Always check the condition of the guide bar

before sharpening the chain. Using a worn

out or damaged guide bar is very dangerous.

Using a worn out or damaged guide bar will

result in damage to the chain. Cutting with such

a power tool will also be much more difﬁ cult and

demanding.

Normal maintenance of the guide bar

Remove the guide bar from the body of the chain saw.

Regularly remove sawdust from the guide bar groove. For cleaning use a spatula or a wire.

Clean oily grooves at the end of every work day.

Replace the guide bar if:

• it is bent or cracked

• its groove is very damaged or worn out

NOTE: To replace the guide bar, follow the instruction contained in this user's manual. You will ﬁ nd the

correct guide bar type in the technical speciﬁ cations.

Guide bar

groove

Guide bar

Standard guide

bar

Guide bar

with uneven

wear

EN 20

FZP 4516 B

Sharpening the saw chain

12. SHARPENING THE SAW CHAIN

Keep the saw chain sharp. Cutting will be signiﬁ cantly faster and most importantly safer. A blunt saw chain

increases wear on the sprocket, guide bar, chain and engine. If you need to push on the saw and only sawdust

with a few splinters are produced then this means that the chain is blunt.

For this task, we recommend that you contact an authorised service centre

Equipment necessary for sharpening a saw chain

Round ﬁ le as per technical speciﬁ cations

Depth gauge

File guide

Vice

Medium-size ﬂ at ﬁ le

Sharpening the teeth on the chain

Use the ﬁ le guide set at an angle of 30°

(mark A, see ﬁ gure).

Set the saw chain tension to the correct level.

Fasten the guide bar in a vice so that you have the

chain in a stable position.

NOTE: Do not fasten the chain itself.

Push the round ﬁ le, inserted in the ﬁ le guide, into

the groove between the top plate and the depth

gauge on the chain. The chain should be touching

both the top plate as well as the depth gauge (see

ﬁ gure)

NOTE: File in the middle of the guide bar.

NOTE: In the ﬁ gure you can see the position of the ﬁ le guide and the direction for ﬁ ling the teeth on the left

side of the chain.

Place the ﬁ le guide at the required angle (mark A, see ﬁ gure). Check that the mark is at 30° on the ﬁ le guide

aligned with the centre of the guide bar. This will ensure that you will ﬁ le at an angle of 30°.

File the tooth in the direction from inside out (in direction B, see ﬁ gure) until it is sharp. File only in this

direction.

NOTE: Two to three passes of the ﬁ le should be sufﬁ cient to sharpen the tooth.

AB

Stránka sa načítava ...

Fieldmann FZP 4516 B Používateľská príručka

Fieldmann FZP 4516 B Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty