HOTPOINT/ARISTON RSF 723 EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
1
GB
WASHING MACHINE
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash option
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
RSF 723
Instructions for use
English,1
GB
Italiano,13
IT
ΕΛΛΗΝΙΚΑ,25
GR
Česky,49
CZ
BG
Áúëãàðñêè,37
Polski,61
PL
2
GB
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine
needs to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture
cabinets or anything
else.
2. If the floor is not perfectly level, compensate
for any unevenness by tightening or loosening
the adjustable front feet (see figure); the angle
of inclination, measured in relation to the
worktop, must not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
(see opposite);
• thesocketiscompatiblewiththeplugof
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is
extremely dangerous to leave the appliance
exposed to rain, storms and other weather
conditions.
65 - 100 cm
! When the washing machine has been
installed, the electricity socket must remain
within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle auto clean (see “Cleaning the
washing machine”).
Technical data
Model
RSF 723
Dimensions
width 59.5 cm
height 85 cm
depth 54 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 9
;
Eco Cotton 60°C.
programme 9
;
Eco Cotton 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU - WEEE
4
GB
Care and maintenance
Cutting off the water and
electricity supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to
prevent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasaautoclean
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10%
the quantity specified
for lightly-soiled
garments) or special
additives to clean the
washing machine. We
recommend running a
cleaning programme every 40 wash cycles.
To start the programme press button A for 5
seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bottom
part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a
screwdriver, remove
the cover panel on
the lower front part of
the washing machine
(see figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
A
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreach
extremely high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderany
circumstances access the internal mechanisms in an
attempt to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of the
washing machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Description of the washing
machine
Control panel
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION button and indicator light: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
CLEANING ACTION button and indicator light
: to
select the desired wash intensity.
TEMPERATURE button: press to reduce or completely
exclude the temperature; the value appears on the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAY TIMER button: press to set a delayed start for
the selected wash cycle; the delay period appears on the
display.
START/PAUSE button and indicator light: when the green
indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
CHILD LOCK button: to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the indicator light is illuminated, the control
panel is locked (apart from the ON/OFF button). This
means it is possible to prevent wash cycles from being
modified accidentally, especially where there are children in
the home. To deactivate the control panel lock, press and
hold the button for approximately 2 seconds.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Antimicrobial seal
The seal around the porthole door is made from a special
mixture ensuring antimicrobial protection, thus reducing
bacterial proliferation up to 99.99%.
The seal contains zinc pyrithione, a biocidal substance
which reduces the proliferation of harmful microbes (*)
such as batteries and mould prone to causing stains,
unpleasant odours and product deterioration.
(*) According to tests performed by the University of Perugia,
Italy on: Staphylococcus aureus, Escherichia coll, Pseudomonas
aeruginosa, Candida albicans, Aspergillus niger, Penicillium digitatum.
In rare cases an allergic reaction may be caused by prolonged contact between
seal and skin.
OPTION
button and
indicator light
CHILD
LOCK
button
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAY
TIMER
button
CLEANING
ACTION
button and
indicator light
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear (the display will show the
maximum duration of the cycle chosen, which may decrease after several minutes, since the effective duration of the
programme varies depending on the wash load and the settings chosen); if the DELAY TIMER option has been set, the
countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the selected
cycle, or the most recently-used settings if they are
compatible with the selected cycle. The temperature
can be decreased by pressing the button, until
the cold wash “OFF” setting is reached. The spin
speed may be progressively reduced by pressing
the button, until it is completely excluded (the
“OFF” setting). If these buttons are pressed again, the
maximum values are restored.
! Exception: if the 3 programme is selected, the
temperature can be increased up to a value of 90°C.
! Exception: if the 4 programme is selected, the
temperature can be increased up to a value of 60°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
For heavily-soiled garments press button until
the “Intensive” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you desire
bleaching, insert the extra tray compartment (4) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central
pivot (see figure pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate
level is reached. The cycle will reduce drum rotation
to ensure washing results that are perfect for delicate
garments.
Modify the cycle settings.
• Pressthebuttontoenabletheoption;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisabletheoption;the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be lit). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an amber colour); then select the desired cycle
and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Wash options
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
Prewash
If this function is selected, the pre-wash cycle will run; this
is useful for removing stubborn stains.
N.B.: Put the detergent in the relevant compartment.
Table of programmes and wash cycles
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
60°C . The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be washed at
40°C . The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set programme 9 at temperature 40°C.
3) Long wash cycle for synthetics: set wash cycle 4 with a temperature of 40°C.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumptionkWh
Total water lt
Cycle dura-
tion
Prewash
Wash
Fabric
softener
Bleach
DAILY CLEAN
1
Anti Stain
40° 1200
- 4 - - -
**
2
Anti Stain Quick
40° 1200 -
- 3,5 - - -
**
3
Cotton: lightly soiled resistant and delicate colours.
40°
(Max. 90°C)
1200
7 - - -
**
4
Synthetics (3): lightly soiled resistant colours.
40°
(Max. 60°C)
1000
3,5 44 0,57 53 100’
5
Mix 30’: to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800
-
- 3 71 0,15 35 30’
SPECIALS
6
Darks
30° 800
-
- 4 - - -
**
7
Delicates
30° 0
-
- 1 - - -
**
8
Wool: for wool, cashmere, etc.
40° 800
-
- 1,5 - - -
**
9
Eco Cotton 60°C
60°/4
(1): heavily soiled whites and resistant colours.
60°
1200 -
- 7 53 0,94 52,5 160’
9
Eco Cotton 40°C
60°/4
(2): lightly soiled resistant and delicate colours.
40°
1200 -
- 7 53 0,93 85 140’
10
Cotton 20°C: lightly soiled resistant and delicate colours.
20°
1200 -
7 - - -
**
EXTRA
11
Baby
40° 1000
4 - - -
**
12
Anti Allergy
60°
1200 -
4 - - -
**
13
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0
-
- 1 - - -
**
14
Duvets: for down-stuffed garments. 30° 1000
-
- 2 - - -
**
Partial Programmes
Rinse
-
1200 - -
- 7 - - -
**
Spin and Pump out
-
1200 - - - - 7 - - -
**
Pump out only *
- OFF
- - - - 7 - - -
**
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents; they create too
much foam.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-
wash detergent (powder)
Before pouring in the
detergent, make sure that
extra compartment 4 has
been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the removable
plastic partition A (supplied) be used for proper dosage.If powder
detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
• Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichreferto
the weight of the laundry when dry: see “Table of
programmes and wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: the programme 1 is suitable to heavily-soiled
garments with resistant colours. It ensures a washing class
that is higher than the standard class (A class). When running
the programme, do not mix garments of different colours. We
recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are obstinate stains.
Anti Stain Quick: this programme is ideal for washing the
most difficult daily stains in 1 hour. It is ideal for mixed fabrics
and coloured garments, caring for your clothes as it washes.
Darks: use cycle 6 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
Delicates: use programme 7 to wash very delicate
garments having strasses or sequins.
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool
garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine (M1126)
Cotton 20°C: the programme 10 ideal for lightly soiled
cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Baby: use the special wash cycle 11 to remove the remove
the soiling typically caused by babies, while removing all
traces of detergent from nappies in order to prevent the
delicate skin of babies from suffering allergic reactions. The
cycle has been designed to reduce the amount of bacteria by
using a greater quantity of water and optimising the effect of
special disinfecting additives added to the detergent.
Anti Allergy: use programme 12 to remove major
allergens such as pollen, mites, cat’s and dog’s hair.
Silk: use special wash cycle 13 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case
or mesh bag. Use wash cycle 13.
Duvets: to wash single duvets (the weight of which should
not exceed 2 kg), cushions or clothes padded with goose
down such as puffa jackets, use the special 14 wash cycle.
We recommend that duvets are placed in the drum with
their edges folded inwards (see figure) and that no more
than ¾ of the total volume of the drum is used. To achieve
the best results, we recommend that a liquid detergent is
used and placed inside the detergent dispenser drawer.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
M
AX
1
2
4
3
A
B
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The “option and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display (e.g.:
F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
• Thewashcycledoesnotincludedraining:somecyclesrequirethedraining
process to be enabled manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for
washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before contacting the Technical Assistance Service:
• Checkwhetheryoucansolvetheproblemalone(see “Troubleshooting”).
• Restartthewashcycletocheckwhethertheproblemhasbeensolved.
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
13
IT
Italiano
Sommario
Installazione, 14-15
Disimballo e livellamento
Collegamenti idraulici ed elettrici
Primo ciclo di lavaggio
Dati tecnici
Manutenzione e cura, 16
Escludere acqua e corrente elettrica
Pulire la lavabiancheria
Pulire il cassetto dei detersivi
Curare oblò e cestello
Pulire la pompa
Controllare il tubo di alimentazione dell’acqua
Precauzioni e consigli, 17
Sicurezza generale
Smaltimento
Apertura manuale della porta oblò
Descrizione della lavabiancheria, 18-19
Pannello di controllo
Display
Come effettuare un ciclo di lavaggio, 20
Programmi e opzioni, 21
Tabella dei programmi
Opzioni di lavaggio
Detersivi e biancheria, 22
Cassetto dei detersivi
Preparare la biancheria
Programmi particolari
Sistema bilanciamento del carico
Anomalie e rimedi, 23
Assistenza, 24
Assistenza Attiva 7 giorni su 7
IT
LAVABIANCHERIA
RSF 723
Istruzioni per l’uso
14
IT
Installazione
! È importante conservare questo libretto per
poterlo consultare in ogni momento. In caso di
vendita, di cessione o di trasloco, assicurarsi
che resti insieme alla lavabiancheria per infor-
mare il nuovo proprietario sul funzionamento e
sui relativi avvertimenti.
! Leggere attentamente le istruzioni: ci sono
importanti informazioni sull’installazione,
sull’uso e sulla sicurezza.
Disimballo e livellamento
Disimballo
1. Disimballare la lavabiancheria.
2. Controllare che la lavabiancheria non abbia
subìto danni nel trasporto. Se fosse danneggia-
ta non collegarla e contattare il rivenditore.
3. Rimuovere le 4 viti
di protezione per il
trasporto e il gommino
con il relativo distan-
ziale, posti nella parte
posteriore (vedi figura).
4. Chiudere i fori con
i tappi di plastica in
dotazione.
5. Conservare tutti i pezzi: qualora la lavabian-
cheria debba essere trasportata, dovranno
essere
rimontati.
! Gli imballaggi non sono giocattoli per bambini.
Livellamento
1. Installare la lavabiancheria su un pavimento
piano e rigido, senza appoggiarla a muri, mobili
o altro.
2. Se il pavimento non
fosse perfettamente
orizzontale, compen-
sare le irregolarità
svitando o avvitando
i piedini anteriori (vedi
figura); l’angolo di
inclinazione, misurato
sul piano di lavoro, non
deve superare i 2°.
Un accurato livellamento dà stabilità alla
macchina ed evita vibrazioni, rumori e spo-
stamenti durante il funzionamento. In caso di
moquette o di un tappeto, regolare i piedini in
modo da conservare sotto la lavabiancheria
uno spazio sufficiente per la ventilazione.
Collegamenti idraulici ed elettrici
Collegamento del tubo di alimentazione
dell’acqua
1. Collegare il tubo
di alimentazione
avvitandolo a un
rubinetto d’acqua
fredda con bocca
filettata da 3/4 gas
(vedi figura).
Prima di allacciare,
far scorrere l’acqua
finché non sia limpi-
da.
2. Collegare il tubo
di alimentazione alla
lavabiancheria
avvitandolo all’appo-
sita presa d’acqua,
nella parte posteriore
in alto a destra (vedi
figura).
3. Fare attenzione che nel tubo non ci siano
né pieghe né strozzature.
! La pressione idrica del rubinetto deve esse-
re compresa nei valori della tabella Dati tecni-
ci (vedi pagina a fianco).
! Se la lunghezza del tubo di alimentazione
non fosse sufficiente, rivolgersi a un negozio
specializzato o a un tecnico autorizzato.
! Non utilizzare mai tubi già usati.
! Utilizzare quelli in dotazione alla macchina.
15
IT
Collegamento del tubo di scarico
Collegare il tubo di
scarico, senza pie-
garlo, a una condut-
tura di scarico o a
uno scarico a muro
posti tra 65 e 100
cm da terra;
oppure appoggiarlo
al bordo di un lavan-
dino o di una vasca,
legando la guida in
dotazione al
rubinetto (vedi figu-
ra). L’estremità libera
del tubo di scarico
non deve rimanere
immersa nell’acqua.
! È sconsigliato usare tubi di prolunga; se in-
dispensabile, la prolunga deve avere lo stes-
so diametro del tubo originale e non superare
i 150 cm.
Collegamento elettrico
Prima di inserire la spina nella presa della
corrente, accertarsi che:
la presa abbia la messa a terra e sia a nor-
ma di legge;
la presa sia in grado di sopportare il carico
massimo di potenza della macchina, indicato
nella tabella Dati tecnici (vedi a fianco);
la tensione di alimentazione sia compresa
nei valori indicati nella tabella Dati tecnici (vedi
a fianco);
la presa sia compatibile con la spina della
lavabiancheria. In caso contrario sostituire la
presa o la spina.
! La lavabiancheria non va installata all’aper-
to, nemmeno se lo spazio è riparato, perché
è molto pericoloso lasciarla esposta a pioggia
e temporali.
! A lavabiancheria installata, la presa della
corrente deve essere facilmente raggiungibile.
! Non usare prolunghe e multiple.
! Il cavo non deve subire piegature o compres-
sioni.
! Il cavo di alimentazione deve essere sostituito
solo da tecnici autorizzati.
Attenzione! L’azienda declina ogni responsabilità
qualora queste norme non vengano rispettate.
Primo ciclo di lavaggio
Dopo l’installazione, prima dell’uso, effettuare
un ciclo di lavaggio con detersivo e senza bian-
cheria impostando il programma auto pulizia
(vedi “Pulire la lavabiancheria”).
65 - 100 cm
Dati tecnici
Modello
RSF 723
Dimensioni
larghezza cm 59,5
altezza cm 85
profondità cm 54
Capacità
da 1 a 7 kg
Collega-
menti elet-
trici
vedi la targhetta caratteristi-
che tecniche applicata sulla
macchina
Collega-
menti idrici
pressione massima 1 MPa
(10 bar)
pressione minima 0,05 MPa
(0,5 bar)
capacità del cesto 52 litri
Velocità di
centrifuga
sino a 1200 giri al minuto
Programmi
di controllo
secondo i
regolamenti
1061/2010
1015/2010
programma 9;
Eco Cotone 60°C;
programma 9;
Eco Cotone 40°C.
Questa apparecchiatura è
conforme alle seguenti Diret-
tive Comunitarie:
- 2004/108/CE (Compatibilità
Elettromagnetica)
- 2012/19/EU - WEEE
- 2006/95/CE (Bassa Tensione)
16
IT
Manutenzione e cura
Escludere acqua e corrente elettrica
Chiudere il rubinetto dell’acqua dopo ogni la-
vaggio. Si limita così l’usura dell’impianto idrau-
lico della lavabiancheria e si elimina il pericolo di
perdite.
Staccare la spina della corrente quando si
pulisce la lavabiancheria e durante i lavori di
manutenzione.
Pulire la lavabiancheria
• La parte esterna e le parti in gomma pos-
sono essere puliti con un panno imbevuto di
acqua tiepida e sapone. Non usare solventi o
abrasivi.
• La lavabiancheria è dotata di un programma
di auto pulizia delle parti interne che deve es-
sere effettuato senza alcun tipo di carico nel
cesto.
Il detersivo (nella quan-
tità pari al 10% di
quella consigliata per
capi poco sporchi) o
additivi specifici per la
pulizia della lavabian-
cheria, potranno essere
utilizzati come coadiu-
vanti nel programma di
lavaggio. Si consiglia di
effettuare il programma di pulizia ogni 40 cicli di
lavaggio.
Per attivare il programma premere il tasto A per
5 sec. (vedi figura).
Il programma partirà automaticamente ed avrà
una durata di circa 70 minuti. Per fermare il
ciclo premere il tasto START/PAUSE.
Pulire il cassetto dei detersivi
Sfilare il cassetto sol-
levandolo e tirandolo
verso l’esterno (vedi
figura).
Lavarlo sotto l’acqua
corrente; questa pulizia
va effettuata
frequentemente.
Curare oblò e cestello
Lasciare sempre socchiuso l’oblò per evitare
che si formino cattivi odori.
Pulire la pompa
La macchina è dotata di una pompa auto-
pulente che non ha bisogno di manutenzio-
ne. Può però succedere che piccoli oggetti
(monete, bottoni) cadano nella precamera
che protegge la pompa, situata nella parte
inferiore di essa.
! Assicurarsi che il ciclo di lavaggio sia termi-
nato e staccare la spina.
Per accedere alla precamera:
1. rimuovere il pan-
nello di copertura
sul lato anteriore
della lavasciuga con
l’ausilio di un giravite
(vedi figura);
2. svitare il coper-
chio ruotandolo in
senso antiorario
(vedi figura): è nor-
male che fuoriesca
un po’ d’acqua;
3. pulire accuratamente l’interno;
4. riavvitare il coperchio;
5. rimontare il pannello assicurandosi, prima
di spingerlo verso la macchina, di aver inseri-
to i ganci nelle apposite asole.
Controllare il tubo di alimenta-
zione dell’acqua
Controllare il tubo di alimentazione almeno
una volta all’anno. Se presenta screpolature e
fessure va sostituito: durante i lavaggi le forti
pressioni potrebbero provocare improvvise
spaccature.
! Non utilizzare mai tubi già usati.
1
2
A
17
IT
Precauzioni e consigli
! La lavabiancheria è stata progettata e costruita in conformi-
alle norme internazionali di sicurezza. Queste avvertenze
sono fornite per ragioni di sicurezza e devono essere lette
attentamente.
Sicurezza generale
Questo apparecchio è stato concepito esclusivamente
per un uso di tipo domestico.
•Questo apparecchio può essere usato da
bambini da 8 anni in su e da persone con
capacità fisiche, sensoriali o mentali ridotte
o con esperienza e conoscenze insufficienti
se sono supervisionati o se hanno ricevuto
adeguata formazione in merito all’uso dell’ap-
parecchio in modo sicuro e capendo i pericoli
connessi. I bambini non devono giocare con
l’apparecchio. Manutenzione e pulizia non
devono essere effettuati dai bambini senza
supervisione.
Non toccare la macchina a piedi nudi o con le mani o i
piedi bagnati o umidi.
• Non staccare la spina dalla presa della corrente tirando il
cavo, bensì afferrando la spina.
• Non aprire il cassetto dei detersivi mentre la macchina è
in funzione.
Non toccare l’acqua di scarico, che p raggiungere
temperature elevate.
Non forzare in nessun caso l’oblò: potrebbe danneggiarsi
il meccanismo di sicurezza che protegge da aperture
accidentali.
In caso di guasto, in nessun caso accedere ai meccanismi
interni per tentare una riparazione.
Controllare sempre che i bambini non si avvicinino alla
macchina in funzione.
• Durante il lavaggio l’oblò tende a scaldarsi.
Se dev’essere spostata, lavorare in due o tre persone con
la massima attenzione. Mai da soli perché la macchina è
molto pesante.
Prima di introdurre la biancheria controlla che il cestello
sia vuoto.
Smaltimento
Smaltimento del materiale di imballaggio:
attenersi alle norme locali, così gli imballaggi potranno
essere riutilizzati.
La direttiva Europea 2012/19/EU (WEEE) sui rifiuti di appa-
recchiature elettriche ed elettroniche (RAEE), prevede che
gli elettrodomestici non debbano essere smaltiti nel normale
flusso dei rifiuti solidi urbani. Gli apparecchi dismessi devono
essere raccolti separatamente per ottimizzare il tasso di
recupero e riciclaggio dei materiali che li compongono ed
impedire potenziali danni per la salute e l’ambiente.
Apertura manuale della porta oblò
Nel caso non sia possibile aprire la porta oblò a causa della
mancanza di energia elettrica e volete stendere il bucato,
procedere come segue:
1. togliere la spina dalla presa
di corrente.
2. verificate che il livello
dell’acqua all’interno della
macchina sia inferiore rispetto
all’apertura dell’oblò; in caso
contrario togliere l’acqua in
eccedenza attraverso il tubo
di scarico raccogliendola in un
secchio come indicato in figura.
3. rimuovere il pannello di
copertura sul lato anteriore della
lavabiancheria con l’ausilio di un
giravite (vedi figura).
4. utilizzando la linguetta indicata in figura tirare verso
l’esterno fino a liberare il tirante in plastica dal fermo; tirarlo
successivamente verso il basso e contemporaneamente
aprire la porta.
5. rimontare il pannello assicurandosi, prima di spingerlo
verso la macchina, di aver inserito i ganci nelle apposite asole.
20
Il simbolo del cestino barrato è riportato su tutti i prodotti per
ricordare gli obblighi di raccolta separata. Quando si acquista
una nuova apparecchiatura equivalente si può consegnare
il RAEE al negoziante, che è tenuto a ritirarlo gratuitamente;
i RAEE di “piccolissime dimensioni” (nessun lato sopra i 25
cm) possono essere consegnati gratuitamente ai negozianti
anche se non si acquista nulla (solo nei negozi con superficie
di vendita superiore a 400 mq).
Per ulteriori informazioni, sulla corretta dismissione degli
elettrodomestici, i detentori potranno rivolgersi al servizio
pubblico preposto o ai rivenditori.
18
IT
Pannello di controllo
Descrizione della lavabiancheria
Tasto
TEMPERATURA
MANOPOLA
PROGRAMMI
Cassetto dei detersivi
Tasto
CENTRIFUGA
Cassetto dei detersivi: per caricare detersivi e additivi
(vedi “Detersivi e biancheria”).
Tasto ON/OFF : premere brevemente il tasto per ac-
cendere o spegnere la macchina. La spia START/PAUSE
che lampeggia lentamente di colore verde indica che la
macchina è accesa. Per spegnere la lavabiancheria durante
il lavaggio è necessario tenere premuto il tasto più a lungo,
circa 3 sec.; una pressione breve o accidentale non permet-
terà lo spegnimento della macchina. Lo spegnimento della
macchina durante un lavaggio in corso annulla il lavaggio
stesso.
MANOPOLA PROGRAMMI: per impostare il programma
desiderato (vedi “Tabella dei programmi”).
Tasto e spia OPZIONE: per selezionare l’opzione disponibile.
La spia relativa all’opzione selezionata rimarrà accesa.
Tasto
TIPO DI LAVAGGIO
: premere per selezionare
l’intensità di lavaggio desiderata.
Tasto TEMPERATURA : premere per ridurre o escludere
la temperatura; il valore viene indicato nel display.
Tasto CENTRIFUGA : premere per ridurre o escludere
del tutto la centrifuga; il valore viene indicato nel display.
Tasto PARTENZA RITARDATA : premere per impo-
stare una partenza ritardata del programma prescelto; il
ritardo viene indicato nel display.
Tasto e spia START/PAUSE: quando la spia verde lam-
peggia lentamente, premere il tasto per avviare un lavaggio.
A ciclo avviato la spia diventa fissa. Per mettere in pausa il
lavaggio, premere nuovamente il tasto; la spia lampegge-
rà con colore ambra. Se il simbolo non è illuminato, si
potrà aprire l’oblò. Per far ripartire il lavaggio dal punto in
cui è stato interrotto, premere nuovamente i tasto.
Tasto BLOCCO TASTI: per attivare il blocco del
pannello di controllo, tenere premuto il tasto per circa
2 secondi. La spia acceso indica che il pannello di
controllo è bloccato (ad eccezione del tasto ON/OFF). In
questo modo si impediscono modifiche accidentali dei
programmi, soprattutto se in casa ci sono dei bambini.
Per disattivare il blocco del pannello di controllo, tenere
premuto il tasto per circa 2 secondi.
Modalità stand by
Questa lavatrice, in conformità alle nuove normative
legate al risparmio energetico, è dotata di un sistema
di autospegnimento (stand by) che entra in funzione
dopo circa 30 minuti nel caso di non utilizzo. Premere
brevemente il tasto ON-OFF e attendere che la macchina
si riattivi.
Guarnizione anti-microbica
La guarnizione dell’oblò è realizzata con una particolare
mescola in grado di garantire una protezione
antimicrobica, riducendo la proliferazione batterica fino al
99,99%.
La guarnizione oblò contiene piritione di zinco, una
sostanza biocida che riduce la proliferazione di microbi
dannosi (*) quali batteri e muffe, che potrebbero causare
macchie, cattivi odori e deterioramento del prodotto.
(*) Secondo test effettuato dall’Università di Perugia su:
Staphylococcus aureus, Escherichia coll, Pseudomonas aeruginosa,
Candida albicans, Aspergillus niger, Penicillium digitatum.
In rari casi il contatto prolungato con la guarnizione potrebbe provocare una
reazione allergica alla pelle.
Tasto e spia
START/PAUSE
DISPLAY
Tasto
PARTENZA
RITARDATA
Tasto
ON/OFF
Tasto e spia
OPZIONE
Tasto
TIPO DI
LAVAGGIO
Tasto
BLOCCO
TASTI
19
IT
Display
Il display è utile per programmare la macchina e fornisce molteplici informazioni.
Viene visualizzata la durata dei vari programmi a disposizione e a ciclo avviato il tempo residuo alla fine dello stesso (il display
visualizzerà la durata massima del ciclo selezionato che potrà diminuire dopo alcuni minuti, in quanto la durata effettiva del
programma varia in base al carico di biancheria e alle impostazioni date); nel caso fosse stata impostata una PARTENZA
RITARDATA, viene visualizzato il tempo mancante all’avvio del programma selezionato.
Inoltre, premendo il relativo tasto, vengono visualizzati i valori massimi della velocità di centrifuga e di temperatura che la
macchina può effettuare in base al programma impostato o gli ultimi valori selezionati se compatibili con il programma scelto.
Spia Oblò bloccato
Il simbolo acceso indica che l’oblò è bloccato. Per evitare danni è necessario attendere che il simbolo si spenga prima di
aprire l’oblò.
Per aprire la porta mentre un ciclo è in corso premere il tasto START/PAUSE; se il simbolo OBLO’ BLOCCATO è spento
sarà possibile aprire l’oblò.
20
IT
Come effettuare un ciclo di
lavaggio
1. ACCENDERE LA MACCHINA. Premere il tasto ;
la spia START/PAUSE lampeggerà lentamente di colore
verde.
2. CARICARE LA BIANCHERIA. Aprire la porta oblò.
Caricare la biancheria facendo attenzione a non superare
la quantità di carico indicata nella tabella programmi della
pagina seguente.
3. DOSARE IL DETERSIVO. Estrarre il cassetto e versare
il detersivo nelle apposite vaschette come spiegato in
Detersivi e biancheria”.
4. CHIUDERE L’OBLO’.
5. SCEGLIERE IL PROGRAMMA. Selezionare con la
manopola PROGRAMMI il programma desiderato; ad
esso è associata una temperatura e una velocità di
centrifuga che possono essere modificate. Sul display
comparirà la durata del ciclo.
6. PERSONALIZZARE IL CICLO DI LAVAGGIO. Agire
sugli appositi tasti:
Modificare la temperatura e/o la centrifuga. La
macchina visualizza automaticamente la temperatura e la
centrifuga massime previste per il programma impostato
o le ultime selezionate se compatibili con il programma
scelto. Premendo il tasto si riduce progressivamente la
temperatura sino al lavaggio a freddo “OFF”. Premendo
il tasto si riduce progressivamente la centrifuga sino
alla sua esclusione “OFF”. Un’ulteriore pressione dei
tasti riporterà i valori al massimo consentito per il ciclo
selezionato.
! Eccezione: selezionando il programma 3 la temperatura
può essere portata sino a 90°.
! Eccezione: selezionando il programma 4 la temperatura
può essere portata sino a 60°.
Impostare una partenza ritardata.
Per impostare la partenza ritardata del programma
prescelto, premere il tasto relativo fino a raggiungere
il tempo di ritardo desiderato. Quando tale opzione è
attiva, sul display si illumina il simbolo . Per rimuovere
la partenza ritardata premere il tasto fino a che sul display
compare la scritta “OFF”.
Impostare l’intensità di lavaggio desiderata.
Il tasto permette di ottimizzare il lavaggio in base
al grado di sporco dei tessuti e all’intensità di lavaggio
desiderata.
Per capi molto sporchi premere il tasto fino al
raggiungimento del livello “Intensive”. Questo livello
garantisce un lavaggio di alte prestazioni grazie all’utilizzo
di una maggiore quantità di acqua nella fase iniziale del
ciclo ed una maggiore movimentazione meccanica, ed è
utile per eliminare le macchie più resistenti. Può essere
utilizzato con o senza candeggina.
Se si desidera effettuare il candeggio inserire la
vaschetta aggiuntiva 4, in dotazione, nella vaschetta 1.
Nel dosare la candeggina non superare il livello “max
indicato sul perno centrale (vedi figura a pag. 22).
Per capi poco sporchi o per un trattamento più
delicatodei tessuti, premere il tasto fino al
raggiungimento del livello “Delicate”. Il ciclo ridurrà la
movimentazione meccanica per garantire risultati di
lavaggio perfetti per i capi delicati.
Modificare le caratteristiche del ciclo.
Premere il tasto per attivare l’opzione; la spia
corrispondente al pulsante si accenderà.
Premere nuovamente il tasto per disattivare
l’opzione; la spia si spegnerà.
! Se l’opzione selezionata non è compatibile con il
programma impostato, la spia lampeggerà e l’opzione
non verrà attivata.
! Le opzioni possono variare il carico raccomandato
e/o la durata del ciclo.
7. AVVIARE IL PROGRAMMA. Premere il tasto
START/PAUSE. La spia relativa si illuminerà di colore
verde fisso e l’oblò si bloccherà (simbolo OBLO’
BLOCCATO acceso). Per cambiare un programma
mentre un ciclo è in corso, mettere la lavabiancheria
in pausa premendo il tasto START/PAUSE (la spia
START/PAUSE lampeggerà lentamente di colore
ambra); selezionare quindi il ciclo desiderato e premere
nuovamente il tasto START/PAUSE.
Per aprire la porta mentre un ciclo è in corso premere il
tasto START/PAUSE; se il simbolo OBLO’ BLOCCATO
è spento sarà possibile aprire l’oblò. Premere
nuovamente il tasto START/PAUSE per far ripartire il
programma dal punto in cui era stato interrotto.
8. FINE DEL PROGRAMMA. Viene indicata dalla
scritta “END” sul display, quando il simbolo OBLO’
BLOCCATO si spegnerà sarà possibile aprire
l’oblò. Aprire l’oblò, scaricare la biancheria e spegnere
la macchina.
! Se si desidera annullare un ciclo già avviato, premere a
lungo il tasto . Il ciclo verrà interrotto e la macchina si
spegnerà.
1 / 1

HOTPOINT/ARISTON RSF 723 EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka