Simplicity 1696204-00 Používateľská príručka

Not for

Reproduction

Part No.: 1752190

Revision: F

Operator’s Manual

Návod k obsluze

Bedienungsanleitung

Ohjekirja

Manual de l’opérateur

Felhasználói kézikönyv

Manuale dell’operatore

Vartotojo vadovas

Bruksanvisningen

Instrukcja obsługi

Руководство по эксплуатации

Návod na obsluhu

Uporabniški priročnik

Instruktions handbok

Not for

Reproduction

2

1

E

H

I

J

K

F

G

2

3

C

5

6

4

Not for

Reproduction

3

English

en

7

8

9

10

11

12

13

Not for

Reproduction

4

14

15

Not for

Reproduction

5

English

en

Manual Contents:

Operator Safety ..................................................................5

Safety System Tests ....................................................... 10

Features and Controls .................................................... 10

Operation ......................................................................... 11

Maintenance .................................................................... 14

Troubleshooting .............................................................. 16

The images in this document are representative, and are

meant to complement the instructional copy they accompany.

Your unit may vary from the images displayed. LEFT and

RIGHT are as seen from the operator’s position.

NOTE: Please refer to the Customer Contact Guide and

Setup Instructions for additional information.

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates an action that could result in damage to

the product.

Operator Safety

Safety Alert Symbol and Signal Words

Hazard Symbol Charts

Snowthrower Hazard Symbols

Symbol Meaning Symbol Meaning

Safety informa-

tion about haz-

ards that can

result in personal

injury.

Read and under-

stand the opera-

tor’s manual

before operating

or servicing the

unit.

Amputation

hazard - rotating

impeller.

Remove the key

before perform-

ing service.

Amputation

hazard - rotating

impeller.

Amputation

hazard - rotating

auger.

Amputation haz-

ard - do not touch

moving parts.

Thrown objects

hazard.

Fire hazard. Explosion haz-

ard.

Shock hazard. Toxic fume haz-

ard.

Hot surface haz-

ard.

Ear protection

recommended

for extended use.

Keep a safe dis-

tance.

Wear safety

glasses.

Keep children

away.

Kickback hazard.

The following products are covered by this manual:

Products Covered by This Manual

1695846, 1695903, 1695903-01, 1695903-02, 1696204-00,

1696204-01, 1696496-00, 1696497-00, 1696498-00

Not for

Reproduction

6

General Safety Warnings

DANGER

Keep hands, feet, and clothing away from rotating parts.

Rotating parts can contact or entangle hands, feet, hair,

clothing, or accessories.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

• Whenever cleaning, repairing, or inspecting the

snowthrower, make sure the engine is OFF, spark

plug wire is disconnected, and all moving parts have

stopped.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Never operate the snowthrower without proper guards,

and other safety devices in place and working.

• Never leave the snowthrower unattended while engine

is running. Always disengage the auger and traction

controls, stop engine, and remove keys.

• Keep all loose clothing away from the front of the

snowthrower and auger. Scarves, mittens, dangling

drawstrings, loose clothes, and pants can quickly

become caught in the rotating device and amputation

will occur. Tie up long hair and remove jewelry.

• Run the machine a few minutes after discharging snow

to prevent freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when

snowthrower is transported or not in use.

DANGER

The discharge chute contains a rotating impeller to throw

snow. Never clear or unclog the discharge chute with your

hands. Fingers can quickly become caught in the impeller.

Always use a clean-out tool.

Failure to observe these safety instructions will result in

traumatic amputation or severe laceration.

WARNING

• Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowthrowers.

• This snowthrower is capable of amputating hands

and feet, and throwing objects. Read and observe all

the safety instructions in this manual. Failure to do so

could result in death or serious injury.

WARNING

Read, understand, and follow all the instructions on the

snowthrower and in the operator’s manual before operating

this unit.

Failure to observe the safety instructions in this manual

could result in death or serious injury.

• Be thoroughly familiar with the controls and the proper

use of the snowthrower.

• Make sure you are properly trained before operating

the snowthrower.

• Know how to stop the unit and disengage the controls

quickly.

• Never allow anyone to operate the snowthrower with-

out proper instruction.

• Always follow the instructions in the operator’s manual,

if the snowthrower will be stored for an extended peri-

od.

• Maintain or replace safety and instruction labels as

necessary.

• Never attempt to make major repairs on the

snowthrower unless you have been properly trained.

Improper servicing of the snowthrower can result in

hazardous operation, equipment damage, and voiding

of the product warranty.

Not for

Reproduction

7

English

en

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nau-

sea, fainting, or death.

• Start and run the engine outdoors.

• Do not run the engine in an enclosed area, even if

doors and windows are open.

WARNING

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

unit and the operating activity. Never assume that children

will remain where you last saw them.

• Keep children out of the area during operation.

Children are often attracted to the equipment. Be

mindful of all persons present.

• Be alert and turn the unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Children may be present.

WARNING

Fuel and its vapors are extremely flammable and explo-

sive. Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a

fire or explosion which will result in severe burns or death.

When Adding Fuel

• Turn off engine and let cool at least 2 minutes before

removing the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion

of gasoline, do not fill above the bottom of the fuel tank

neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting

engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air clean-

er (if equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but

move the snowthrower away from the area of the spill,

and avoid creating any source of ignition, until the fuel

vapors have dissipated.

• Do not over-prime the engine. Follow the engine start-

ing instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/

RUN position, move throttle (if equipped) to FAST

position and crank until engine starts.

When Operating Equipment

• Do not tip the snowthrower at an angle which causes

the fuel to spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if

equipped) or the air filter (if equipped) removed.

When Changing Oil

• If you drain the oil from the top oil fill tube, the fuel tank

must be empty or fuel can leak out and result in a fire

or explosion.

When Transporting Equipment

• Transport with fuel tank EMPTY, or with fuel shut-off

valve OFF.

When Storing Gasoline or Equipment With Fuel in

Tank

• Store away from furnaces, stoves, water heaters, or

other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

Objects can be picked up by the auger and thrown from

the chute. Never discharge snow toward bystanders

or allow anyone in front of the snowthrower. Failure to

observe these safety instructions will result in death or

serious injury.

• Always wear safety glasses or eye shields during oper-

ation, and while performing an adjustment or repair.

• Always be aware of the direction the snow is being

thrown. Nearby pedestrians, pets, or property may be

harmed by objects being thrown.

• Be aware of your environment while operating the

snowthrower. Don’t run over items such as gravel,

doormats, newspapers, toys, and rocks hidden under

snow, as they can all be thrown from the chute or jam

in the auger.

• Use extreme caution when operating on or crossing

gravel drives, walks, or roads.

• Adjust the collector housing height to clear gravel or

crushed rock surface.

• Never operate the snowthrower near glass enclo-

sures, automobiles, window wells, drop-offs, and the

like without proper adjustment of the discharge chute

angle.

• Familiarize yourself with the area in which you plan to

operate the snowthrower. Mark off boundaries of walk-

ways and driveways.

Not for

Reproduction

8

WARNING

Safe operation of the snowthrower requires the proper care

and maintenance of the engine.

• Disengage all clutches and shift into neutral before

starting the engine.

• Let the engine adjust to outdoor temperatures before

starting to clear snow.

• Use a grounded three-wire plug for all snowthrowers

equipped with electric drive motors or electric starting

motors.

WARNING

Starting the engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• If there is natural gas or LP gas leakage in the area, do

not start the engine.

• Do not use pressurize starting fluids because their

vapors are flammable.

WARNING

Running the engine produces heat. Engine parts, espe-

cially the muffler, become extremely hot.

Failure to observe these safety instructions could result in

severe thermal burns on contact.

• Never touch a hot engine or muffler. Allow muffler,

engine cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester

before using equipment on forest-covered, grass-cov-

ered, or brush-covered unimproved land.

• U.S.A. Models: It is a violation of California Public

Resource Code Section 4442 to use or operate the

engine on any forest-covered, brush-covered, or

grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

WARNING

This snowthrower must be properly maintained to ensure

safe operation and performance. Failure to observe the

safety instructions in this manual could result in death or

serious injury.

• When performing any maintenance or repairs on the

snowthrower, shut OFF the engine, disconnect spark

plug wire, and keep the wire away from the plug to pre-

vent someone from accidently starting the engine.

• Check shear bolts and other hardware at frequent

intervals for proper tightness.

• Keep nuts and bolts tight and keep snowthrower in

good condition.

• Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they

are not functioning properly.

• Components are subject to wear, damage, and dete-

rioration. Frequently check components and replace

with recommended parts, when necessary.

• Check control operation frequently. Adjust and service

as required.

• Use only factory authorized replacement parts, or like,

parts when making repairs.

• Always comply with factory specifications on all set-

tings and adjustments.

• Use only factory authorized, or like, attachments and

accessories such as wheel weights, counterweights,

or cabs.

• Never attempt to make any adjustments while the

engine is running (except when specifically recom-

mended by the factory).

Not for

Reproduction

9

English

en

WARNING

This snowthrower is only as safe as the operator. If it is

misused, or not properly maintained, it can be dangerous.

Remember you are responsible for your safety and those

around you.

• Keep the area of operation clear of all persons, par-

ticularly small children and pets.

• Thoroughly inspect the area where the snowthrower

will be used and remove all doormats, sleds, boards,

wires, and other foreign objects.

• Do not operate the snowthrower without wearing ade-

quate winter clothing.

• Wear footwear that will improve footing on slippery sur-

faces.

• Use caution to avoid slipping or falling especially when

operating the snowthrower in reverse.

• Never operate the snowthrower without good visibility

or light. Always be sure of your footing, and keep a firm

hold on the handles.

• Do not clear snow across the face of slopes. Use

extreme caution when changing direction on slopes.

Do not attempt to clear steep slopes.

• Do not overload the machine capacity by attempting to

clear snow too quickly.

• Never operate the snowthrower at high transport

speeds on slippery surfaces. Look behind the

snowthrower and use care when operating in reverse.

• Do not use the snowthrower on surfaces above ground

level such as roofs of residences, garages, porches, or

other such structures or buildings.

• Operators should evaluate their ability to operate the

snowthrower safely enough to protect themselves and

others from injury.

• The snowthrower is intended to remove snow only. Do

not use the snowthrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine,

disconnect the cord on electric motors, thoroughly

inspect the snowthrower for any damage, and repair

the damage before restarting and operating the

snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the

engine. Vibration is generally a warning of trouble. See

an authorized dealer if necessary for repairs.

• For models equipped with electric starting motors, dis-

connect the power cord after the engine starts.

WARNING

Damaged or ungrounded power cords could cause electric

shock.

Electric shock could cause severe burns or death.

When Using the Electric Starter

• The power cord must be properly grounded at all

times.

• Use only a three-conductor power cord properly

grounded to the power source.

• If the power cord is damaged, it must be replaced by a

qualified person to avoid a hazard.

WARNING

Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

When starting the engine

• Pull the starter cord slowly until resistance is felt and

then pull rapidly to avoid kickback.

Before operating your unit, read the safety decals. Compare

Figure 1 with the table below. The cautions and warnings are

for your safety. To avoid a personal injury or damage to the

unit, understand and follow all the safety decals.

Safety Decals

WARNING

If any safety decals become worn or damaged, and

cannot be read, order replacement decals from your

local dealer.

A Chute Danger Decal

(P/N 1727207)

B Auger Danger Decal

(P/N 1737867)

C Engine Warning Decal

(P/N 276925)

Not for

Reproduction

10

Safety System Tests

Safety System Test (units with Free

Hand control)

WARNING

Amputation hazard

This snowthrower is equipped with several mechanical

safety systems designed to keep the operator safe while

using the unit. Check the operation of these systems regu-

larly using the safety system tests listed. If the unit fails to

operate as described, DO NOT operate it. See your autho-

rized dealer for service immediately.

Test 1 - Auger/Impeller Control

With the engine running:

• Press down on the auger control lever. (The auger/

impeller should rotate)

• Release the auger control lever. (The auger/impeller

must stop within 5 seconds)

Test 2 - Traction Drive Control

With the engine running and speed control in 1st gear:

• Press down on the traction control lever. (The unit

should move forward)

• Release the traction control lever. (The unit must stop)

Test 3 - Free Hand Control

With the engine running:

• Engage the auger and traction control levers, then

release the auger control lever. (Both controls should

remain engaged)

• Next, release the traction control lever. (Both controls

must release)

Features and Controls

Engine Features and Controls

Snowthrower Features and Controls

For engine features and controls, please refer to the engine

operator’s manual.

Compare Figure 2 with the table below.

A

1

R1

R2

2

3

Speed Select Lever - Allows

the operator to use one of

five forward and two reverse

speeds. To shift, move speed

select lever to desired position.

NOTICE: Do not move speed

select lever while Traction

Control is engaged. This

may result in severe damage

to the drive system.

B

Auger Control Lever - Used

to engage and disengage the

auger and impeller. To engage,

push down. To disengage,

release.

C

Chute Rotation Switch - Used

to rotate the discharge chute to

the left or right.

D Chute Deflector Control

Lever (if equipped) - Used to

control the angle of the deflec-

tor (up or down).

E Chute Deflector Switch (if

equipped) - Used to control

the angle of the deflector (up or

down).

F Traction Control Lever - Used

to propel snowthrower for-

ward or reverse. Push down to

engage, release to disengage.

See also, “Free-Hand Control”.

G Free Hand™ Control - After

engaging the traction control

(left hand) and auger control

(right hand), allows the opera-

tor to release the auger control

lever to use other controls.

H

Easy Turn™ Traction Control

- When engaged, allows the

operator to release one drive

wheel, but allows the other

wheel to continue driving for

easy turning.

Not for

Reproduction

11

English

en

Operation

Before Operating the Snowthrower

WARNING

Read the operator’s manual before operating the

machine. This machine can be dangerous if used

carelessly.

• Never operate the snowthrower without all guards,

covers, and shields in place.

• Stop the engine whenever leaving the operating posi-

tion.

• Remove the key before unclogging the impeller hous-

ing or discharge chute, and before making repairs or

adjustments.

• When leaving the machine, remove the key.

• To reduce the risk of fire, keep the machine clean and

free from spilled fuel, oil, and debris.

• On electric start models, disconnect the extension cord

before operating.

• Be sure to check the engine oil level before starting the

engine. See the engine operator’s manual for oil recom-

mendations.

Operating the Snowthrower

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to

throw snow. Fingers can quickly become caught in

the impeller. Never clear or unclog the discharge

chute with your hands. Always use a clean-out tool.

Failure to observe these safety instructions will result

in traumatic amputation or severe laceration.

Hand contact with the rotating impeller inside the dis-

charge chute is the most common cause of injury associ-

ated with snowthrowers. Never use your hands to clean out

the discharge chute.

To safely clear a clogged discharge chute, follow

these instructions:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

WARNING

Thrown objects hazard

This machine is capable of throwing objects that could

injure bystanders, or cause damage to buildings.

Be sure the operating area is clear of bystanders. Never

direct the discharge toward anyone, or toward buildings or

cars.

DANGER

Toxic fume hazard

Engines give off carbon monoxide, an odorless, col-

orless, poison gas.

Breathing carbon monoxide can cause nausea, faint-

ing, or death.

• Start and run the engine outdoors.

• Do not run the engine in an enclosed area, even if

doors and windows are open.

1. Start the engine. Please refer to the engine operator’s

manual for engine information.

2. Use the chute rotation switch (C, Figure 2) to set the

direction of the discharge chute.

3. Use the chute deflector control lever (D, if equipped) or

chute deflector switch (E, if equipped) to raise and lower

the deflector. Raise the deflector to throw snow further.

I Grip Warmer Switch - Used

to warm the hand grips (high,

off, low).

J

-

Clean-Out Tool - Used to

remove snow and debris from

the discharge chute and the

auger housing.

K

-

Skid Shoes - Used to adjust

the ground clearance of the

auger housing.

Not for

Reproduction

12

4. Use the speed select lever (A) to select the forward or

reverse drive speed. Use lower speeds when clearing

wet, heavy snow. Use higher speeds for light snow or

transporting.

NOTE: Always set engine speed to FAST (full throttle).

5. Fully press the auger control lever (B) to engage the

auger. Releasing the auger control lever will stop the

auger, unless the Free Hand control (G) is activated.

6. Fully press and hold the traction control/Free Hand lever

(F, G) to engage the traction drive and begin moving the

snowthrower. To stop, release the lever.

NOTE: Always release the traction control lever before

changing speeds.

7. When both the auger and traction control levers are

pressed, the Free Hand control is activated. This allows

you to release the auger control to use other controls.

The auger will continue to rotate until the traction control/

Free Hand control is released.

8. If desired, use the grip warmer switch (I) to turn on the

heated hand grips.

For easy turning when using the snowthrower, squeeze the

Easy Turn traction control lever (Figure 3).

NOTE: Some models feature Easy Turn traction control for

one wheel only, while other models feature it for both wheels.

NOTE: Easy Turn traction control will be more difficult to acti-

vate under a heavy load. Activate the lever before beginning

a turn.

Engaging the Easy Turn traction control lever releases one

of the traction wheels, but allows the other wheel to continue

driving. Releasing the Easy Turn traction control lever auto-

matically engages both drive wheels for full traction (Figure

4).

Easy Turn™ Traction Control (if

equipped)

1. Release the auger control lever (B, Figure 2).

2. Release the traction control lever (H).

3. Stop the engine. Please refer to the engine operator’s

manual for engine instructions.

Stopping the Snowthrower

Chute Deflector Adjustment

While the engine is running, press either side of the chute

rotation switch (A, Figure 6) to rotate the discharge chute (B)

left or right.

Chute Rotation Adjustment

Wheels equipped with a traction lock pin (A, Figure 7) can be

completely released by removing the pin and installing it in

the outer axle hole. Reverse this process to engage the drive

wheel.

Wheel Release - Lock Pins (if equipped)

Please refer to the engine operator’s manual for information

about filling the fuel tank, and for fuel recommendations.

A clean-out tool (A, Figure 8) is provided with the unit.

Filling the Fuel Tank

Clearing a Clogged Discharge Chute

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to

throw snow. Fingers can quickly become caught in

the impeller. Never clear or unclog the discharge

chute with your hands. Always use a clean-out tool.

Failure to observe these safety instructions will result

in traumatic amputation or severe laceration.

Hand contact with the rotating impeller inside the dis-

charge chute is the most common cause of injury associ-

ated with snowthrowers. Never use your hands to clean out

the discharge chute.

To safely clear a clogged discharge chute, follow

these instructions:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

Move the chute deflector control lever (A, Figure 5) forward

or backward to raise and lower the deflector (B). Raise the

deflector to throw snow further.

While the engine is running, press either side of the chute

deflector switch (C, Figure 5) to raise and lower the deflector

(B). Raise the deflector to throw snow further.

Chute Deflector Control Lever (if equipped)

Chute Deflector Switch (if equipped)

Not for

Reproduction

13

English

en

This snowthrower is equipped with two height adjust skids,

secured to the outside of the auger housing. These elevate

the front of the snowthrower.

When removing snow from a hard surface area such as a

paved driveway or walk, adjust the skids up to bring the front

of the snowthrower down.

When removing snow from gravel-covered or uneven sur-

faces, raise the front of the snowthrower by moving the skids

down. This will help to prevent rocks and other debris from

being picked up and thrown by the augers.

1. Determine how much clearance you want between the

scraper bar at the bottom of the auger housing and the

ground. If clearing a gravel surface, enough ground clear-

ance is needed to prevent the unit from picking up rocks.

2. Place a block equal to the desired ground clearance

under the scraper bar.

3. Loosen the skid shoe mounting nuts (A, Figure 9) and

push the skid shoe (B) down until it touches the ground.

Re-tighten mounting nuts.

4. Set the skid shoe on the other side at the same height.

Skid Shoe Height Adjustment

DANGER

Amputation hazard

The discharge chute contains a rotating impeller to throw

snow. Fingers can quickly become caught and traumatic

amputation or severe laceration will result. Hand contact

with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrow-

ers.

Turn the engine OFF, wait for all moving parts to stop, and

remove the engine key before performing any maintenance

or repairs.

WARNING

Thrown objects hazard

Objects such as gravel, rocks, or other debris, if struck

by the impeller, may be thrown with sufficient force to

cause personal injury, property damage, or damage to the

snowthrower.

Be sure to set the skid shoes at the proper height to main-

tain ground clearance for the type of surface being cleared.

If the unit will be stored for 30 days or more at the end of the

season, the following steps are recommended to prepare it

for storage. Always refer to the operator’s manual for impor-

tant details if the unit is to be stored for an extended period.

Please refer to the engine operator’s manual for engine stor-

age information.

NOTE: Fuel must be removed or treated to prevent gum

deposits from forming in the tank, filter, hose, and carburetor

during storage.

Off-Season Storage

WARNING

Fire and explosion hazard

Gasoline is highly flammable and its vapors are explosive.

Fumes may travel to a distant ignition source and an explo-

sion and/or fire may result.

Handle gasoline carefully. Never store the unit, with fuel in

the tank, indoors or in a poorly ventilated enclosure where

fuel fumes could reach an open flame, spark, pilot light,

such as a furnace, water heater, or clothes dryer.

• Thoroughly clean the unit.

• Lubricate all lubrication points (see Maintenance sec-

tion).

• Make sure all nuts, bolts, and screws are securely fas-

tened. Inspect all visible moving parts for damage, break-

age, and wear. Replace if necessary.

• Touch up all rusted or chipped paint surfaces; sand light-

ly before painting.

• Cover the bare metal parts of the snowthrower housing

auger, and the impeller with rust preventative.

• If possible, store your unit indoors and cover it to give

protection from dust and dirt.

• If the machine must be stored outdoors, cover with a

heavy tarpaulin.

To Return to Service:

• Fill the fuel tank with a fresh fuel.

• Make sure all fasteners are tight.

• Make sure all guards, shields, and covers are in place.

Not for

Reproduction

14

Maintenance

Maintenance Schedule

Before Each Use

• Check engine oil level

• Perform Safety System Test

Every 8 Hours or Daily

• Check engine oil level

Every 25 Hours or Annually

• Lubricate control lever linkages

• Lubricate the auger assembly

• Lubricate the discharge chute rotation gear and

deflector

• Lubricate the hex shaft with 5w-30 synthetic motor oil,

and chains with grease

Every 50 Hours or Annually

• Check muffler and spark arrester (if equipped)

• Check tire pressure

For engine maintenance schedules and procedures, please

refer to the engine operator’s manual.

Lubricate the unit at the locations show in Figure 10. Where

an oil can is pictured, lubricate with engine oil. Where a

grease gun is pictured, lubricate with lithium grease.

Engine Maintenance

Control Lever Linkage Lubrication

WARNING

Amputation hazard

It is critical for safe operation of the unit that the controls

disengage when released. Under no circumstances should

the unit be used if the controls do not function properly.

See Safety Systems Tests to confirm correct operation.

The auger gear box is lubricated at the factory and should

not require additional lubrication. However, if lubricant has

leaked out or the auger gear box has been serviced, addi-

tional lubricant may be required.

To check the auger gear box grease level, remove the filler

plug (A, Figure 11). Using a piece of wire as a dipstick, check

to confirm the presence of grease in the gearbox. If grease is

visible, do not add. If grease is not visible, add the required

lubricant (Lubriplate GR132 Grease or equivalent). Gearbox

lubricant capacity is 3-1/4 ounces (92 grams).

Lubricate Auger Gear Box

Auger Assembly Lubrication

Using a grease gun, lubricate the auger shaft fittings (B,

Figure 11). Refer to the Maintenance Schedule. Each time a

shear bolt or pin (C) is replaced, the auger shaft MUST be

greased.

For storage or when replacing shear bolts or pins, remove

the shear bolts or pins (C), lubricate the shaft fittings (B),

and rotate the augers several times to distribute the grease.

Reinstall the shear bolts or pins when complete.

Lubricate the chute rotation gear (Figure 12) with grease, and

the deflector mechanism with automotive type oil. Refer to

the Maintenance Schedule.

Where an oil can is pictured, lubricate with engine oil. Where

a grease gun is pictured, lubricate with lithium grease.

Lubricate Auger Shaft Fittings

Discharge Chute and Deflector

Lubrication

The hex shaft and drive chains must be lubricated at the

interval specified in the Maintenance Schedule. Please have

your authorized dealer perform this maintenance.

Hex Shaft and Chain Lubrication (if

equipped)

The cables are adjusted at the factory and no adjustment

should be necessary. However, if the cables have become

stretched or are sagging, adjustment will be necessary.

Please see your dealer for this adjustment.

Traction Cable Inspection

Not for

Reproduction

15

English

en

The traction drive belt is under constant spring tension and

does not require any adjustment. If the traction drive belt is

slipping, see your authorized dealer.

If the Easy Turn cable has stretched, the gears will not dis-

engage when the control lever is activated. Adjust the cable

using the following procedure.

1. Turn the engine off and remove the key.

2. Loosen the jam nut (A, Figure 13).

3. Turn the adjustment nut (B) to lengthen or shorten the

cable. The cable should be tightened until all slack is

removed from the lever. However, it must not engage the

Easy Turn without depressing the control lever.

4. Tighten the jam nut (A).

If the speed control rod requires adjustment, see an autho-

rized dealer.

Traction Drive Belt Adjustment

Easy Turn™ Cable Adjustment

Speed Control Rod Adjustment

1. With the auger control lever released, the hook (A, Figure

14) should barely touch the lever (B) without raising it.

There can be a maximum of 1/32” (0.8 mm) clearance.

2. To adjust, loosen the nut (C) by holding the adjustment

screw (D) and turning the nut. Then, turn the turnbuckle

and hold the adjustment screw (D). The adjustment

screw is a phillips screw and the head can be held or

turned by inserting a screwdriver through the spring.

3. Hold the screw and tighten the nut to secure.

4. To ensure that the auger does not engage unless the

control is fully depressed, please perform the Safety

System Test. The auger must stop within 5 seconds

of the control being released.

Auger Cable Adjustment

WARNING

Amputation hazard

Over-tightening the auger cable may cause the auger drive

to engage without depressing the auger drive control.

Follow the adjustment procedure to ensure the cable is not

over-tightened.

The augers are secured to the auger shaft with special shear

pins that are designed to break if an object becomes lodged

in the auger housing. Use of a harder grade shear pin will

reduce the protection provided by the shear pin.

Under most circumstances, if the auger strikes an object

which could cause damage to the unit, the shear pin will

break. This protects the gear box and other parts from dam-

age.

NOTICE

Do not replace the shear pins with anything other than the

correct grade replacement shear pin. Use of bolts, screws, or

harder grade shear pins can result in equipment damage.

Auger Shear Pin Replacement

WARNING

Amputation hazard

The discharge chute contains a rotating impeller to throw

snow. Fingers can quickly become caught and traumatic

amputation or severe laceration will result. Hand contact

with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrow-

ers.

Turn the engine OFF, wait for all moving parts to stop, and

remove the engine key before performing any maintenance

or repairs.

The shear pins and clips (A and B, Figure 15) are located on

the auger shaft. Replace a broken shear pin as follows.

1. Tap out the broken shear pin with a pin punch.

2. Install a new shear pin and cotter pin. Bend the ends of

the cotter pin down.

Tire pressure should be checked periodically. Recommended

tire pressure varies by tire manufacturer. A good rule of

thumb is to inflate the tire up to, but not exceeding, the “Max

Inflation” stamped on the side-wall of the tire.

Checking Tire Pressure

Not for

Reproduction

16

Troubleshooting

Troubleshooting Chart

Perform the inspection or repair as indicated in the Troubleshooting Chart.

Problem Look for Remedy

Auger does not stop within 5 seconds

after right control lever is released.

Free Hand control (if equipped) is

ACTIVE.

Release both auger control and Free

Hand control (if equipped) to stop

auger.

Auger drive belt out of adjustment. See authorized dealer.

Auger belt guide out of adjustment. See authorized dealer.

Discharge chute or deflector does not

work (electric).

Electrical failure. See authorized dealer.

Discharge chute or deflector does not

work

(remote-manual).

Discharge chute or deflector out of

adjustment or needs lubrication.

Adjust and/or lubricate control linkage.

Drive fails to move snowthrower at slow

speeds.

Traction control out of adjustment. See authorized dealer.

Engine fails to start. Key is in OFF position. Set key to ON position.

Failure to prime a cold engine. Press primer button twice and restart.

Fuel shut-off valve, if equipped, is in

CLOSED position.

Turn valve to OPEN position.

Out of fuel. Fill fuel tank.

Choke turned to OPEN/RUN with cold

engine.

Turn choke to CLOSED/START, set

throttle to FAST.

Engine flooded. Move the choke to OPEN/RUN posi-

tion, move throttle to FAST position,

and crank until the engine starts.

No spark. See authorized dealer.

Engine starts hard or runs poorly. Water in fuel, or old fuel. Drain tank. (Dispose of fuel at an autho-

rized hazardous waste facility.) Fill with

fresh fuel.

Spark plug faulty, fouled, or gapped

improperly.

See authorized dealer.

Fuel cap vent is blocked. Clear vent.

Excessive vibration. Loose parts or damaged impeller. Stop engine immediately. Tighten all

hardware. If vibration continues, have

the unit serviced by an authorized

dealer.

Snowthrower does not stop when trac-

tion control lever is released.

Traction control out of adjustment. See authorized dealer.

Scraper bar does not clean hard sur-

face.

Skid shoes and scraper bar improperly

adjusted.

Raise or lower skid shoes and scraper

bar.

Unit fails to propel itself. Drive belt loose or damaged. Replace drive belt. See authorized

dealer.

Incorrect adjustment of traction drive

cable.

See authorized dealer.

Worn or damaged friction disc. Replace friction disc. See authorized

dealer.

Not for

Reproduction

17

English

en

Problem Look for Remedy

Unit fails to discharge snow. Auger drive belt loose or damaged. See authorized dealer.

Auger control cable not adjusted cor-

rectly.

Adjust auger control cable. Refer to

Maintenance section of this manual.

Broken shear pin or shear bolt. Replace shear pin or bolt. Refer to

Maintenance section of this manual, or

see an authorized dealer.

Discharge chute clogged. Stop engine immediately. Always use

the clean-out tool to clear a clogged

discharge chute, not your hands. Clean

discharge chute and inside of auger

housing. Refer to Discharge Chute

Warning in the Operator Safety section.

Foreign object lodged in auger. Stop engine immediately. Always use

the clean-out tool to clear a clogged

chute, not your hands. Remove object

from auger. Refer to WARNINGS in the

Operator Safety section.

Not for

Reproduction

18

Not for

Reproduction

5

Česky

cs

Obsah návodu:

Bezpečnost obsluhy ..........................................................5

Bezpečnostní testy systému .......................................... 10

Funkce a ovládání ........................................................... 10

Provoz ............................................................................... 11

ÚDRŽBA ............................................................................ 14

Řešení problémů ............................................................. 16

Obrázky v tomto dokumentu jsou pro ilustraci, doprovázejí

dokument s pokyny, se kterým jsou dodány. Vaše jednotka se může

od zobrazených obrázků lišit. LEVÁ a PRAVÁ jsou zobrazeny z

pozice obsluhy.

POZNÁMKA: Další informace naleznete v Průvodci pro kontakt se

zákazníky a v Pokynech pro nastavení.

Bezpečnostní varovný symbol poukazuje na možné riziko

poranění. Signální slova (NEBEZPEČÍ, VAROVÁNÍ nebo POZOR)

jsou používána s varovnou značkou k upozornění na stupeň

vážnosti rizika. Bezpečnostní značka může být navíc použita k

reprezentaci typu rizika. Signální slovo UPOZORNĚNÍ se používá k

upozornění na postupy, které nejsou spojeny s poraněními.

NEBEZPEČÍ ukazuje riziko, které, jestliže se mu nevyvarujete,

povede ke smrti nebo vážnému poranění.

VAROVÁNÍ ukazuje na riziko, které, jestliže se mu nevyvarujete,

může vést ke smrti nebo vážnému poranění.

POZOR ukazuje na riziko, které, jestliže se ho nevyvarujete,

může vést k malému či střednímu poranění.

UPOZORNĚNÍ ukazuje na situaci, která by mohla vést k poškození

výrobku.

Bezpečnost obsluhy

Bezpečností varovné značky a signální

slova

Tabulky značek rizik

Značky rizik pro sněhovou frézu

Značka Význam Značka Význam

Bezpečnostní

informace o

rizicích, která

mohou vést k

poraněním.

Před provozem či

servisem jednotky

si přečtěte návod

k obsluze a

porozumějte mu.

Riziko amputace -

rotor.

Před prováděním

servisu vyndejte

klíč.

Riziko amputace -

rotor.

Riziko amputace -

rotující šnek.

Riziko amputace

- nedotýkejte se

pohybujících se

částí.

Nebezpečí

odhazovaných

předmětů.

Riziko požáru. Riziko výbuchu.

Riziko šoku. Riziko toxických

plynů.

Riziko horkého

povrchu.

Při delším použití

se doporučuje

ochrana uší.

Udržujte

bezpečnou

vzdálenost.

Používejte

ochranné brýle.

Nedovolte přístup

dětem.

Riziko zpětného

rázu

Tento návod týká následujících produktů:

Výrobky, kterých se týká tento

návod

1695846, 1695903, 1695903-01, 1695903-02, 1696204-00,

1696204-01, 1696496-00, 1696497-00, 1696498-00

Not for

Reproduction

6

Obecná bezpečnostní varování

NEBEZPEČÍ

Nohy a ruce udržujte z dosahu rotujících částí. Rotující části

mohou přijít do kontaktu s rukama, nohama, vlasy, oděvy či

doplňky.

Nedodržení těchto bezpečnostních pokynů může vést k

amputacím či vážným laceracím.

• Při čištění, opravách či kontrolách sněhové frézy se ujistěte,

že motor je v poloze VYPN, svíčka je odpojená a všechny

pohyblivé části se zastavily.

• Pod rotující části či do jejich blízkosti nedávejte ruce nebo

nohy. Nikdy neblokujte výstup.

• Frézu nikdy nepoužívejte bez řádných krytů a jiných

ochranných pomůcek.

• Jestliže běží motor, sněhovou frézu nikdy neponechávejte

bez dozoru. Vždy deaktivujte šneka a kontrolu trakce,

vypněte motor a vyndejte klíčky.

• Udržujte všechny volné oděvy z dosahu přední části frézy

a šneku. Šály, rukavice, šňůrky a volné oděvy se mohou

rychle zachytit v rotujícím zařízení a může dojít k amputacím.

Svažte si dlouhé vlasy a sundejte šperky.

• Po ukončení odstraňování sněhu frézu nechte několik minut

běžet, aby se předešlo zamrznutí sběrače a rotoru.

• Jestliže se fréza nepoužívá nebo je převážená, deaktivujte

pohon sběrače/rotoru.

NEBEZPEČÍ

Odpadový žlab zahrnuje rotujícího šneka k odhazování sněhu.

Odpadový žlab nikdy nečistěte rukama. V rotoru může snadno

dojít k zachycení prstů. Vždy používejte čistící nástroj.

Nedodržení těchto bezpečnostních pokynů může vést k

amputacím či vážným laceracím.

VAROVÁNÍ

• Nejčastější poranění při použití sněhové frézy vznikají při

kontaktu rukou s poháněčem odpadového nosníku.

• Tato sněhová fréza je schopna amputovat ruce a nohy

a odhazovat předměty. Přečtěte si a dodržujte všechny

bezpečnostní pokyny v tomto návodu. Jestliže tak neučiníte,

může to vést ke smrti či vážným poraněním.

VAROVÁNÍ

Před spuštěním této jednotky si přečtěte, porozumějte a

dodržujte všechny pokyny na sněhové fréze a v návodu k

obsluze.

Nedodržení bezpečnostních pokynů v tomto návodu může vést

ke smrti či vážnému poranění.

• Důkladně se seznamte s ovladači a s řádným použitím

sněhové frézy.

• Ujistěte se, že před použitím sněhové frézy jste řádně

vyškoleni.

• Ujistěte se, že víte, jak rychle přístroj zastavit a deaktivovat.

• Nikdy nedovolte, aby se sněhovou frézou zacházely osoby

bez řádných pokynů.

• Jestliže má být fréza uložena na delší dobu, vždy postupujte

podle pokynů v návodu k obsluze.

• Udržujte bezpečnostní nálepky a, jestliže je to nutné,

vyměňte je.

• Jestliže jste k tomu nebyli řádně vyškoleni, nikdy se sami

nepokoušejte provést žádné větší opravy sněhové frézy.

Nesprávný servis sněhové frézy může vést k nebezpečnému

provozu, poškození zařízení a porušení záruky.

Stránka sa načítava ...

Simplicity 1696204-00 Používateľská príručka

Táto príručka je tiež vhodná pre

Simplicity 1696204-00 Používateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty