Husqvarna LC 247S Návod na obsluhu

LC 247, LC 247S, LC 247SP, LC 253S,

LC 347V, LC 347VI, LC 353V, LC 353VI

EN Operator's manual 6-19

BG Ръководство за експлоатация 20-34

CS Návod k použití 35-48

DA Brugsanvisning 49-62

DE Bedienungsanweisung 63-77

EL Οδηγίες χρήσης 78-93

ES Manual de usuario 94-108

ET Kasutusjuhend 109-122

FI Käyttöohje 123-136

FR Manuel d'utilisation 137-151

HR Priručnik za korištenje 152-165

HU Használati utasítás 166-179

IT Manuale dell'operatore 180-194

LT Operatoriaus vadovas 195-208

LV Lietošanas pamācība 209-223

NL Gebruiksaanwijzing 224-237

NO Bruksanvisning 238-250

PL Instrukcja obsługi 251-265

PT Manual do utilizador 266-280

RO Instrucţiuni de utilizare 281-295

RU Руководство по эксплуатации 296-311

SK Návod na obsluhu 312-325

SL Navodila za uporabo 326-339

SR Priručnik za rukovaoca 340-353

SV Bruksanvisning 354-367

TR Kullanım kılavuzu 368-381

UK Посібник користувача 382-396

1

2

5

4

3

6

8

9

10

11

7

14

19

17

15

16

12

13

1

18

1

2 3 4 5 6 7

8 9 10 11 12 13

14 15 16 17 18 19

20 21

22

23 24

B

A

25 26

27 28

29 30

31 32

33 34

35 36

37 38

A

39 40

41 42

43 44

Contents

Introduction..................................................................... 6

Safety..............................................................................7

Assembly...................................................................... 10

Operation...................................................................... 10

Maintenance................................................................. 12

Transportation, storage and disposal........................... 15

Technical data.............................................................. 15

EC Declaration of Conformity....................................... 19

Introduction

Product description

The product is a pedestrian-controlled rotary lawn

mower. The grass is collected in a grass catcher.

Remove the grass catcher to get rear discharge of the

grass. Attach a mulch kit (accessory) to cut the grass

into fertilizer.

Intended use

Use the product to cut grass in private gardens. Do not

use the product for other tasks.

Product overview

(Fig. 1)

1. Engine brake handle / Start bar (LC 347VI,

LC 353VI)

2. Handle / handlebar

3. Start inhibitor (LC 347VI, LC 353VI)

4. Drive bail (LC 247S, LC 247SP)

5. Speed control

6. Grass catcher

7. Rear cover

8. Handle height adjustment

9. Dipstick/Oil tank

10. Battery, safety device (LC 347VI, LC 353VI)

11. Cutting cover

12. Muffler

13. Spark plug

14. Air filter

15. Fuel tank

16. Cutting height control

17. Primer bulb (LC 247, LC 247S)

18. Starter rope handle (not on LC 347VI, LC 353VI)

19. Operator's manual

Symbols on the product

(Fig. 2) WARNING: Careless or incorrect use can

result in serious or fatal injury to the operator

or others.

(Fig. 3) Please read the operator's manual carefully

and make sure that you understand the

instructions before use.

(Fig. 4) Keep persons and animals at a safe

distance from the work area.

(Fig. 5) Stop the engine and remove the ignition

cable before repairs or maintenance.

(Fig. 6) Dipstick/oil filter

(Fig. 7) Look out for thrown objects and ricochets.

(Fig. 8) Warning: rotating blade. Keep hands and

feet clear.

(Fig. 9) Warning: rotating parts. Keep hands and

feet clear.

(Fig. 10) This product is in accordance with

applicable EC directives.

(Fig. 11) Noise emission to the environment

according to the European Community’s

Directive. The product’s emission is

specified in the Technical data chapter and

on the label.

(Fig. 12) Fast.

(Fig. 13) Slow.

(Fig. 14) Choke.

(Fig. 15) Risk of explosion.

(Fig. 16) The exhaust fumes from the engine contain

carbon monoxide, an odourless, poisonous

and very dangerous gas. Do not start the

engine indoors or in closed spaces.

(Fig. 17) The product does not have oil in the engine

when you purchase it.

(Fig. 18) Fill with oil before you operate the product.

(Fig. 19) Refuel. Do not use fuel that is sold as E85

(85% ethanol).

(Fig. 20) Hot surface.

6 808 - 004 -

(Fig. 22) Remove the safety switch (battery) before

you do maintenance work or let the product

stay out of view.

(Fig. 21) Scannable code.

Note: Other symbols/decals on the product refer to

certification requirements for some commercial areas.

Euro V Emissions

WARNING: Tampering with the engine voids

the EU type-approval of this product.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not from

the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of injury or

death for the operator or bystanders if the

instructions in the manual are not obeyed.

CAUTION: Used if there is a risk of damage

to the product, other materials or the

adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary in

a given situation.

General safety instructions

WARNING: Read the warning instructions

that follow before you use the product.

• This product is dangerous if used incorrectly or if you

are not careful. Injury or death can occur if you do

not obey the safety instructions.

• This product produces an electromagnetic field

during operation. This field may under some

circumstances interfere with active or passive

medical implants. To reduce the risk of serious or

fatal injury we recommend persons with medical

implants to consult their physician and the medical

implant manufacturer before operating this product.

• Always be careful and use your common sense. If

you are not sure how to operate the product in a

special situation, stop and speak to your Husqvarna

dealer before you continue.

• Keep in mind that the operator will be held

responsible for accidents that involve other persons

or their property.

• Keep the product clean. Make sure that you can

clearly read signs and decals.

• Do not let a person use the product unless you make

sure that they read and understand the contents of

the operator's manual.

• Do not let a child operate the product.

• Keep children away from the work area. A

responsible adult must be there at all times.

• Do not let a person, without knowledge of the

instructions, operate the product.

• Always monitor a person, with decreased physical

capacity or mental capacity, that uses the product. A

responsible adult must be there at all times.

• Do not use the product if you are tired, ill, or under

the influence of alcohol, drugs or medicine. This has

a negative effect on your vision, alertness,

coordination and judgment.

• Do not use the product if it is defective.

• Do not change this product or use it if it is possible

that it has been changed by others.

Work area safety

WARNING: Read the warning instructions

that follow before you use the product.

• Remove objects such as branches, twigs and stones

from the work area before you use the product.

• Objects that hit against the cutting equipment can

eject and cause damage to persons and objects.

Keep bystanders and animals at a safe distance

from the product.

• Never use the product in bad weather such as fog,

rain, strong winds, intense cold and risk of lightning.

To use the product in bad weather or in moist or wet

locations is tiring. Bad weather can cause dangerous

conditions, such as slippery surfaces.

• Look out for persons, objects and situations that can

prevent safe operation of the product.

808 - 004 -

7

• Look out for obstacles, such as roots, stones, twigs,

pits and ditches. Long grass can hide obstacles.

• To cut grass on slopes can be dangerous. Do not

use the product on ground that slopes more than

15°.

• Operate the product across the face of slopes. Do

not move up and down.

• Be careful when you go near hidden corners and

objects that prevent a clear view.

Work safety

WARNING: Read the warning instructions

that follow before you use the product.

• Use this product to cut grass lawns only. It is not

permitted to use it for other tasks.

• Use personal protective equipment. Refer to

Personal protective equipment on page 8

.

• Make sure that you know how to stop the engine

quickly in an emergency.

• Never start the engine in a closed space or near

flammable material. The exhaust fumes from the

engine are hot and can contain sparks which can

start a fire.

• Do not operate the product unless the blade and all

covers are attached correctly. An incorrectly

attached blade can come loose and cause personal

injury.

• Make sure that the blade does not hit objects such

as stones and roots. This can do damage to the

blade and bend the engine shaft. A bent axle causes

heavy vibration and a very high risk that the blade

becomes loose.

• If the blade hits an object or if vibrations occur, stop

the product immediately. Disconnect the ignition

cable from the spark plug. Examine the product for

damages. Repair damages or let an authorised

service agent do the repair.

• Never attach the engine brake handle permanently

to the handle when the engine is started.

• Put the product on a stable, flat surface and start it.

Make sure that the blade does not hit the ground or

other objects.

• Always stay behind the product when you operate it.

• Let all the wheels stay on the ground and keep 2

hands on the handle when you operate the product.

Keep your hands and feet away from the rotating

blades.

• Do not tilt the product when the engine is started.

• Be careful when you pull the product rearward.

• Never lift up the product when the engine is started.

If you must lift the product, first stop the engine and

disconnect the ignition cable from the spark plug.

• Do not walk rearward when you operate the product.

• Stop the engine when you move across areas

without grass, for example paths made of gravel,

stone and asphalt.

• Do not run with the product when the engine is

started. Always walk when you operate the product.

• Stop the engine before you change the cutting

height. Never make adjustments with the engine

started.

• Never let the product stay out of view with the engine

started. Stop the engine and make sure that the

cutting equipment does not rotate.

Safety instructions for operation

Personal protective equipment

WARNING: Read the warning instructions

that follow before you use the product.

• Personal protective equipment cannot fully prevent

injury but it decreases the degree of injury if an

accident does occur. Let your dealer help you select

the right equipment.

• Use hearing protection if the noise level is higher

than 85 dB.

• Use heavy-duty slip-resistant boots or shoes. Do not

use open shoes or go with bare feet.

• Use heavy, long pants.

• Use protective gloves when necessary, for example

when you attach, examine or clean the cutting

equipment.

Safety devices on the product

WARNING: Read the warning instructions

that follow before you use the product.

• Do not use a product with defective safety devices.

• Do a check of the safety devices regularly. If the

safety devices are defective, speak to your

Husqvarna service agent.

To do a check of the cutting cover

The cutting cover decreases vibrations in the product

and decreases the risk of injury from the blade.

• Examine the cutting cover to make sure that there

are no damages such as cracks.

Battery (LC 347VI, LC 353VI)

WARNING: A defective battery decreases

the safety of the product. Always use a

battery approved by the manufacturer.

The battery gives power to the electrical start and is a

safety device that prevents accidental start. Remove the

battery when you do not operate the product and when

you let it stay out of view.

8

808 - 004 -

Engine brake handle

The engine brake handle stops the engine. When the

engine brake handle is released, the engine stops and

the drive disengages.

To do an inspection of the engine brake, start the engine

and then release the engine brake handle. If the engine

does not stop in 3 seconds, let an approved Husqvarna

service agent adjust the engine brake.

(Fig. 23)

Start inhibitor

On model LC 347VI, LC 353VI the engine brake handle

is also used as a start bar for the starter motor. Do a

check of the start inhibitor to make sure that it prevents

operation of the starter motor.

1. Pull the start bar in the direction of the handlebar (B).

The start inhibitor stops the movement.

2. Push the start inhibitor out to the right (A). (Fig. 24)

3. Release the start inhibitor and make sure that it goes

back to its initial position.

Muffler

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Do not use the product if the muffler is missing or

defective. A defective muffler increases the noise level

and the risk of fire.

WARNING:

The muffler becomes very hot

during and after use and when the engine

operates at idle speed. Be careful near

flammable materials and/or fumes to prevent

fire.

Fuel safety

WARNING:

Read the warning instructions

that follow before you use the product.

• Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel/oil and let

the product dry.

• If you spill fuel on your clothing, change clothing

immediately.

• Do not get fuel on your body, it can cause injury. If

you get fuel on your body, use soap and water to

remove the fuel.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the fumes

are explosive and can cause injuries or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you refuel.

• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Do not add fuel to the engine in an indoor area. Not

sufficient airflow can cause injury or death because

of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

• Move the product a minimum of 3 m / 10 ft from the

position where you filled the tank before a start.

• Do not fill the fuel tank fully. Heat causes the fuel to

expand. Keep a space at the top of the fuel tank.

Safety instructions for maintenance

WARNING: Read the warning instructions

that follow before you use the product.

• The exhaust fumes from the engine contain carbon

monoxide, an odourless, poisonous and very

dangerous gas. Do not start the engine indoors or in

closed spaces.

• Before you do the maintenance on the product, stop

the engine and remove the ignition cable from the

spark plug. On LC 347VI, LC 353VI, also remove the

battery.

• Use protective gloves when you do maintenance on

the cutting equipment. The blade is very sharp and

cuts can easily occur.

• Accessories and changes to the product that are not

approved by the manufacturer, can cause serious

injury or death. Do not change the product. Always

use accessories that are approved by the

manufacturer.

• If the maintenance is not done correctly and

regularly, the risk of injury and damage to the

product increases.

• Only do the maintenance as given in this owner's

manual. All other servicing must be done by an

approved Husqvarna service agent.

• Let an approved Husqvarna service agent do

servicing on the product regularly.

• Replace damaged, worn or broken parts.

808 - 004 -

9

Assembly

Introduction

WARNING: Before you assemble the

product, read the safety chapter. On

LC 347VI, LC 353VI, also remove the

battery.

To assemble the handle

1. Loosen the lower knobs.

2. Move the knobs to the lower end of the grooves on

the left and the right side of the product. (Fig. 25)

3. Set the handle height in one of the 2 available

positions.

4. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 26)

5. Tighten the knobs fully.

To set the product in transport position

1. Loosen the lower knobs.

2. Move the knobs to the lower end of the grooves on

the left and the right side of the product. (Fig. 25)

3. Fold the handle forward. (Fig. 27)

To set the product in operation position

1. Fold the handle to upright position. (Fig. 28)

2. Move the knobs up in the direction of the handle until

they stop and you hear a click. (Fig. 26)

3. Tighten the knobs fully.

To assemble the grass catcher

1. Attach the grass catcher frame to the grass bag with

the rigid part of the bag on the bottom. Keep the

handle of the frame on top of the grass bag. (Fig. 29)

2. Attach the bottom section of the grass catcher frame

in the groove on the bottom of the grass catcher.

3. Attach the grass bag to the grass catcher frame with

the clips. (Fig. 30)

4. Lift the rear cover.

5. Attach the grass catcher to the top edge of the

chassis.

6. Put the lower part of the grass catcher into the grass

discharge channel. (Fig. 31)

To assemble the mulch plug

(accessory)

1. Lift up the rear cover and remove the grass catcher.

2. Put the mulch plug into the discharge channel. (Fig.

32)

3. Replace the blade with the mulch blade that is

supplied in the mulch kit. Refer to

To replace the

blade on page 13

.

To cut grass without a grass catcher or

mulch plug attached

• Lift up the rear cover and remove the grass catcher.

• If a mulch plug and a mulch blade are attached,

remove them.

• Close the rear cover before you operate the product.

When you operate the product, the cut grass discharges

below the rear cover.

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

Husqvarna Connect

Husqvarna Connect is a free app for your mobile device.

The Husqvarna Connect app gives extended functions

for your Husqvarna product:

• Extended product information.

• Information about, and help with, product parts and

servicing.

To start to use Husqvarna Connect

1. Download the Husqvarna Connect app on your

mobile device.

2. Register in the Husqvarna Connect app.

3. Do the instruction steps in the Husqvarna Connect

app to connect and register the product.

Before you operate the product

1. Read the operator's manual carefully and make sure

that you understand the instructions.

2. Examine the cutting equipment to make sure that it

is correctly attached and adjusted. See

To examine

the cutting equipment on page 12

.

10 808 - 004 -

3. Fill the fuel tank. See

To fill fuel on page 11

.

4. Fill the oil tank and do a check of the oil level. See

To do a check of the oil level on page 13

.

To fill fuel

If available, use low-emission/alkylate gasoline. If low-

emission/alkylate gasoline is not available, use good

quality unleaded gasoline or leaded gasoline with octane

number not less than 90.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove it

with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

5. Move the product a minimum of 3 m (10 ft) from the

position where you filled the tank before a start.

To set the cutting height

The cutting height can be adjusted in 6 levels.

1. Move the cutting height lever rearward to decrease

the cutting height.

2. Move the cutting height lever forward to increase the

cutting height. (Fig. 33)

CAUTION:

Do not set the cutting height too

low. The blades can hit the ground if the

surface of the lawn is not level.

To start the product

• Make sure that the ignition cable is connected to the

spark plug.

Manual start (not on LC 347VI, LC 353VI)

1. For LC 247, LC 247S: The very first time you start

the product, press the primer bulb 5 times. The next

time you start the product when the engine is cold,

press the primer bulb 3 times.

2. Stay behind the product.

3. Hold the engine brake handle against the handlebar.

(Fig. 34)

4. Hold the starter rope handle with your right hand.

5. Slowly pull out the starter rope until you feel some

resistance.

6. Pull with force to start the engine.

WARNING: Do not twist the starter rope

around your hand.

Electrical start (LC 347VI, LC 353VI)

1. Make sure that the battery is activated and charged.

See

To start the battery on page 13

.

2. Attach the battery to the engine. (Fig. 35)

3. Push the start inhibitor out to the right (A).

4. Pull the start bar (B) against the handlebar to start

the starter motor. The starter motor stops when the

engine starts. (Fig. 24)

To use the drive on the wheels

• For LC 247S, LC 247SP: Pull the drive bail in the

direction of the handlebar. (Fig. 36)

• For LC 347V, LC 347VI, LC 353V, LC 353VI: Start

the drive on the wheels with the speed control lever

on the left side of the handle. Move the speed

control lever forward to increase the speed and

rearward to decrease the speed. (Fig. 37)

• Before you pull the product rearward, disengage the

drive and push the product forward approximately

10 cm.

• Release the drive bail to disengage the drive, for

example when you go near an obstacle.

To stop the product

• To stop the engine, release the engine brake handle.

To remove the battery

To prevent accidental start of the engine, remove the

battery on model LC 347VI, LC 353VI when the product

is not in operation.

1. Press the lock buttons (A) and pull the battery out.

(Fig. 38)

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

808 - 004 -

11

Maintenance

Introduction

WARNING: Before you do maintenance, you

must read and understand the safety

chapter.

For all servicing and repair work on the product, special

training is necessary. We guarantee the availability of

professional repairs and servicing. If your dealer is not a

service agent, speak to them for information about the

nearest service agent.

Maintenance schedule

WARNING: For model LC 347VI, LC 353VI,

always remove the battery before you do

maintenance, repairs or clean the product.

The maintenance intervals are calculated from daily use

of the product. The intervals change if the product is not

used daily.

For maintenance marked with * see instructions in

Safety devices on the product on page 8

.

Maintenance Daily Weekly Monthly

Do a general inspection X

Examine the oil level X

Clean the product X

Examine the cutting equipment X

Examine the cutting cover and protective cover* X

Examine the engine brake handle* X

Examine the battery* X

Examine the muffler* X

Examine the spark plug X

Change the oil (the first time after 5 h use, then after each 50 h use) X

Change the air filter (after 50 h use) X

Examine the fuel system X

To do a general inspection

• Make sure that all nuts and screws on the product

are tightened correctly.

To clean the product externally

• Use a brush to remove leaves, grass and dirt.

• Make sure that the air intake on the top of the engine

is not blocked.

• Do not use a high pressure washer to clean the

product.

• If you use water to clean the product, do not flush

water directly on the engine.

To clean the inner surface of the cutting

cover

1. Empty the fuel tank.

2. Put the product on its side with the muffler down.

CAUTION: If the product is put with the

air filter down, the engine can become

damaged.

3. Hose down the inner surface of the cutting cover

with water.

To examine the cutting equipment

WARNING: To prevent accidental start

remove the ignition cable from the spark

plug.

WARNING: Use protective gloves when you

do maintenance on the cutting equipment.

The blade is very sharp and cuts can easily

occur.

12 808 - 004 -

1. Examine the cutting equipment for damage or

cracks. Always replace a damaged cutting

equipment.

2. Look at the blade to see if it is damaged or blunt.

Note: It is necessary to balance the blade after it is

sharpened. Let a service center sharpen, replace and

balance the blade. If you hit an obstacle that causes the

product to stop, replace the damaged blade. Let the

service center estimate if the blade can be sharpened or

must be replaced.

To replace the blade

1. Lock the blade with a block of wood. (Fig. 39)

2. Remove the blade bolt.

3. Remove the blade.

4. Examine the blade support and blade bolt to see if

there are damages.

5. Examine the engine shaft to make sure that it is not

bent.

6. When you attach the new blade, point the angled

ends of the blade in the direction of the cutting cover.

(Fig. 40)

7. Make sure that the blade is aligned with the center of

the engine shaft.

8. Lock the blade with a block of wood. Attach the

spring washer and tighten the bolt and washer with a

torque of 70 Nm. (Fig. 41)

9. Pull the blade around by hand and make sure that it

turns freely.

WARNING: Use heavy duty gloves. The

blade is very sharp and cuts can easily

occur.

10. Start the product to do a test of the blade. If the

blade is not correctly attached, there is vibration in

the product or the cutting result is unsatisfactory.

To do a check of the oil level

CAUTION:

A too low oil level can do

damage to the engine. Do a check of the oil

level before you start the product.

1. Put the product on level ground.

2. Remove the oil tank cap with the attached dipstick.

3. Clean the oil from the dipstick.

4. Put the dipstick fully into the oil tank to give a correct

picture of the oil level.

5. Remove the dipstick.

6. Examine the oil level on the dipstick.

7. If the oil level is low, fill with engine oil and do a

check of the oil level again.

To replace the engine oil

WARNING: Engine oil is very hot directly

after the engine is stopped. Let the engine

become cool before you drain the engine oil.

If you spill engine oil on your skin, clean with

soap and water.

1. Operate the product until the fuel tank is empty.

2. Remove the ignition cable from the spark plug.

3. Remove the oil tank cap.

4. Put a container below the product to collect the

engine oil in.

5. Tilt the product to drain the engine oil from the oil

tank.

6. Fill with new engine oil of the type recommended in

Technical data on page 15

.

7. Do a check of the oil level. Refer to

To do a check of

the oil level on page 13

.

Battery (LC 347VI, LC 353VI)

WARNING: A defective battery decreases

the safety of the product. Always use a

battery approved by the manufacturer.

The battery gives power to the electrical start and is a

safety device that prevents accidental start. Remove the

battery when you do not operate the product and when

you let it stay out of view.

To start the battery

You need to start the battery before the first time you

use it.

1. Put the battery into the charger, see

To charge the

battery on page 13

.

2. Wait until a minimum of 1 green lamp comes on,

approximately 10 seconds.

3. Attach the battery to the engine, see

Electrical start

(LC 347VI, LC 353VI) on page 11

.

To charge the battery

If only 1 or 0 lamp indicators on the battery are on, it is

necessary to charge it. An empty battery is fully charged

in 1 hour. To charge for shorter periods of time does not

do damage to the battery.

1. Put the battery in the battery charger. (Fig. 42)

2. Connect the battery charger to a power socket,

220V, 50Hz.

Status for battery charge

LED display on the battery

Status

LED 1 flashes 0%-25%

808 - 004 - 13

LED display on the battery Status

LED 1 is lit, LED 2 flashes 25%-50%

LED 1, LED 2 are lit, LED 3 flashes 50%-75%

LED 1, LED 2, LED 3 are lit, LED 4

flashes

75%-100%

LED 1, LED 2, LED 3, LED 4 are lit Fully charged

Lamp indicator on the bat-

tery charger

Status

Constant red light The battery charges

Flashing red light The battery is too warm

and will start to charge

when the temperature is

correct

Constant green light The battery is fully charg-

ed

Flashing red and green

light

The battery is damaged

and must be replaced

Air filter

An air filter that is used for a long time cannot be fully

cleaned. Replace the air filter at regular intervals.

All models except LC 247, LC 247S have a paper filter.

LC 247, LC 247S have a foam plastic filter.

Note:

Always replace a damaged air filter.

To clean the paper filter

1. Remove the air filter cover and remove the paper

filter.

2. Hit the filter against a flat surface to make the

particles fall off.

CAUTION:

Do not use solvent or

compressed air to clean the paper filter.

3. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

4. Put the air filter cover back.

To clean the foam plastic filter

1. Remove the air filter cover and remove the foam

plastic filter.

2. Clean the foam plastic filter with soap and water.

3. Flush the foam plastic filter in clean water.

4. Squeeze the water from the foam plastic filter and let

it dry.

CAUTION: Do not use compressed air. It

can cause damage to the foam plastic

filter.

5. Lubricate the foam plastic filter with engine oil.

6. Press a clean cloth against the foam plastic filter to

remove unwanted oil.

7. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

8. Put the air filter cover back.

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to

Technical data

on page 15

. (Fig. 43)

• Replace the spark plug if it is necessary.

To examine the fuel system

• Examine the fuel tank cap and the seal for the fuel

tank cap to make sure that there are no damages.

• Examine the fuel hose to make sure that there are

no leaks. If the fuel hose is damaged, let a service

agent replace it.

To adjust the clutch wire

If the drive starts to feel slow, it is necessary to adjust

the clutch wire.

1. To increase the drive speed, turn the adjuster screw

counterclockwise.

Note:

If the drive is engaged when you do not pull

the drive bail, it is necessary to extend the wire.

2. To extend the wire and decrease the drive speed,

turn the adjustment screw clockwise. (Fig. 44)

If the drive feels slow also after the adjustment, let an

approved service agent replace the drive belt.

14

808 - 004 -

To adjust the clutch wire for the

adjustable speed (LC 347V, LC 347VI,

LC 353V, LC 353VI)

If the engine is started and the slowest speed cannot be

engaged, it is necessary to adjust the speed control.

1. To increase the drive speed, turn the adjuster screw

counterclockwise.

Note: If the drive is engaged when you do not

operate the speed control, it is necessary to extend

the wire.

2. To extend the wire and decrease the drive speed,

turn the adjustment screw clockwise. (Fig. 44)

If the drive feels slow also after the adjustment, let an

approved service agent replace the drive belt.

Transportation, storage and disposal

Transportation and storage

• For storage and transportation of the product and

fuel, make sure that there are no leaks or fumes.

Sparks or open flames, for example from electrical

devices or boilers, can start a fire.

• Always use approved containers for storage and

transportation of fuel.

• Empty the fuel tank before you put the product in

storage for a long period of time. Discard the fuel at

an applicable disposal location

• Safely attach the product during transportation to

prevent damage and accidents.

• Keep the product in a locked area to prevent access

for children or persons that are not approved.

• Keep the product in a dry and frost free area.

Disposal

• Obey the local recycling requirements and applicable

regulations.

• Discard all chemicals, such as engine oil or

antifreeze, at a service center or at an applicable

disposal location.

• When the product is no longer in use, send it to a

Husqvarna dealer or discard it at a recycling

location.

• Discard the battery at a service center or discard it at

a disposal location for used batteries.

Technical data

LC 247 LC 247S LC 247SP LC 253S

Engine

Brand Briggs & Stratton Briggs & Stratton Briggs & Stratton Briggs & Stratton

Displacement, cm

3

125 125 140 163

Speed, rpm 2900 2900 2900 2800

Nominal engine output, kW

1

1.8@2900 1.8@2900 2.1@2900 2.4@2800

Ignition system

Spark plug Champion

QC12YC

Champion

QC12YC

Champion

QC12YC

Champion

XC92YC

Electrode gap, mm 0.5 0.5 0.5 0.5

Fuel and lubrication system

Fuel, unleaded, minimum octane

number

90 90 90 90

Fuel tank capacity, litre 0.8 0.8 0.8 1.0

1

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production

engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ

from this value. Actual power output for the engine installed on the final product will depend on the operating

speed, environmental conditions and other values.

808 - 004 - 15

LC 247 LC 247S LC 247SP LC 253S

Oil tank capacity, litre 0.5 0.5 0.5 0.5

Engine oil

2

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

Weight

With empty tanks, kg 27.5 29.5 30.0 32.4

Noise emissions

3

Sound power level, measured dB (A) 96 96 94 96

Sound power level, guaranteed L

WA

dB (A)

96 96 96 97

Sound levels

4

Sound pressure level at the opera-

tor's ear, dB (A)

85 85 84 85

Vibration levels

5

Handle, m/s

2

3.4 3.4 3.4 4.0

Cutting equipment

Cutting height, mm 20–75 20–75 20–75 20–75

Cutting width, mm 470 470 470 530

Blade Collect Collect Collect Collect

Article number 5882755-10 5882755-10 5882755-10 5797972-10

Grass catcher capacity, l 55 55 55 60

Drive

Speed, km/h – 4 4 4

Start

Electric starter No No No No

Battery – – – –

LC 347V LC 347VI LC 353V LC 353VI

Engine

Brand Briggs & Stratton Briggs & Stratton Briggs & Stratton Briggs & Stratton

Displacement, cm

3

163 163 163 163

2

Use engine oil of quality SF, SG, SH, SJ or higher. See the viscosity chart in the engine manufacturer’s man-

ual and select the best viscosity based on the expected outside temperature.

3

Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive

2000/14/EC.

4

Noise pressure level according to ISO 5395. Reported data for noise pressure level has a typical statistical

dispersion (standard deviation) of 1.2 dB (A).

5

Vibration level according to ISO 5395. Reported data for vibration level has a typical statistical dispersion

(standard deviation) of 0.2 m/s

2

.

16 808 - 004 -

LC 347V LC 347VI LC 353V LC 353VI

Speed, rpm 2900 2900 2800 2800

Nominal engine output, kW

6

2.4@2900 2.6@2900 2.4@2800 2.6@2800

Ignition system

Spark plug Champion

XC92YC

Champion

XC92YC

Champion

XC92YC

Champion

XC92YC

Electrode gap, mm 0.5 0.5 0.5 0.5

Fuel and lubrication system

Fuel, unleaded, minimum octane

number

90 90 90 90

Fuel tank capacity, litre 1.0 1.0 1.0 1.0

Oil tank capacity, litre 0.5 0.5 0.5 0.5

Engine oil

7

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

SAE 30/SAE

10W-30

Weight

With empty tanks, kg 30.0 32.0 32.8 34.2

Noise emissions

8

Sound power level, measured dB (A) 95 95 96 96

Sound power level, guaranteed L

WA

dB (A)

96 96 97 97

Sound levels

9

Sound pressure level at the opera-

tor's ear, dB (A)

84 84 85 85

Vibration levels

10

Handle, m/s

2

4.2 4.2 4.0 4.0

Cutting equipment

Cutting height, mm 20–75 20–75 20–75 20–75

Cutting width, mm 470 470 530 530

Blade Collect Collect Collect Collect

Article number 5882755-10 5882755-10 5797972-10 5797972-10

6

The power rating of the engine indicated is the average net output (at specified rpm) of a typical production

engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ

from this value. Actual power output for the engine installed on the final product will depend on the operating

speed, environmental conditions and other values.

7

Use engine oil of quality SF, SG, SH, SJ or higher. See the viscosity chart in the engine manufacturer’s man-

ual and select the best viscosity based on the expected outside temperature.

8

Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive

2000/14/EC.

9

Noise pressure level according to ISO 5395. Reported data for noise pressure level has a typical statistical

dispersion (standard deviation) of 1.2 dB (A).

10

Vibration level according to ISO 5395. Reported data for vibration level has a typical statistical dispersion

(standard deviation) of 0.2 m/s

2

.

808 - 004 - 17

LC 347V LC 347VI LC 353V LC 353VI

Grass catcher capacity, l 55 55 60 60

Drive

Speed, km/h 2.8–5.0 2.8–5.0 2.8–5.0 2.8–5.0

Start

Electric starter No Yes No Yes

Battery – Li-ion 10.8V/

15.7WH

– Li-ion 10.8V/

15.7WH

18 808 - 004 -

EC Declaration of Conformity

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:

+46-36-146500, declares that the lawn mowers

Husqvarna LC 247, LC 247S, LC 247SP, LC 253S,

LC 347V, LC 347VI, LC 353V and LC 353VI from the

serial numbers 2016xxxxxxx and onwards comply with

the requirements of the COUNCIL’S DIRECTIVE:

• of May 17, 2006 ”relating to machinery” 2006/42/EC

• of February 26, 2014 ”relating to electromagnetic

compatibility” 2014/30/EU

• of May 8, 2000 ”relating to the noise emissions in the

environment” 2000/14/EC

Information relating to noise emissions, see Technical

data.

The following standards have been applied:

EN ISO 5395-1, EN ISO 5395-2, EN ISO 5395-2 Amd1,

EN ISO 5395-2 Amd 2, EN ISO 14982

If not otherwise stated, the above listed standards are

the latest published versions.

Notified body: 0404, RISE SMP Svensk Maskinprovning

AB, Box 7035, SE-750 07 Uppsala has issued reports

regarding the assessment of conformity according to

annex VI of the COUNCIL’S DIRECTIVE of May 8,

2000 ”relating to the noise emissions in the

environment” 2000/14/EC.

The certificate has the number: 01/901/264, 01/901/265,

01/901/281, 01/901/282

Huskvarna, 2016-11-01

Claes Losdal, Development Manager/Garden Products

(Authorized representative for Husqvarna AB and

responsible for technical documentation)

808 - 004 -

19

Содержание

Въведение................................................................... 20

Безопасност.................................................................21

Монтаж.........................................................................24

Операция..................................................................... 25

Поддръжка...................................................................26

Транспортиране, съхранение и изхвърляне.............30

Технически характеристики....................................... 31

Декларация за съответствие на ЕО.......................... 34

Въведение

Описание на продукта

Продуктът е пешеходна ротационна косачка.

Тревата се събира в кош за трева. Свалете коша за

трева, за да се получи задно разтоварване на

тревата. Поставете комплект за мулчиране

(допълнителна принадлежност), за да нарежете

тревата в тора.

Предназначение

Използвайте продукта, за да косите трева в частни

градини. Не използвайте продукта за други задачи.

Общ преглед на продукта

(Фиг. 1)

1. Дръжка за спирачката на двигателя/стартовата

шина(LC 347VI, LC 353VI)

2. Дръжка/управление

3. Блокировка на пускане (LC 347VI, LC 353VI)

4. Дръжка за задвижване (LC 247S, LC 247SP)

5. Управление на оборотите

6. Кош за трева

7. Заден капак

8. Регулиране на височината на ръчката

9. Мерителна пръчка/резервоар за масло

10. Акумулатор, предпазно устройство (LC 347VI,

LC 353VI)

11. Капак срещу порязване

12. Ауспух

13. Запалителна свещ

14. Въздушен филтър

15. Резервоар за гориво

16. Управление на височината на рязане

17. Подкачваща помпа (LC 247, LC 247S)

18. Дръжка на въжето на стартера (не се отнася за

LC 347VI, LC 353VI)

19. Инструкция за експлоатация

Символи върху машината

(Фиг. 2) ПРЕДУПРЕЖДЕНИЕ: Немарливото или

неправилното им използване може да

доведе до сериозна или фатална травма

на оператора и заобикалящите го.

(Фиг. 3) Прочетете внимателно ръководството за

оператора и се уверете, че разбирате

инструкциите, преди да използвате

машината.

(Фиг. 4) Дръжте хората и животните на безопасно

разстояние от работната зона.

(Фиг. 5) Спрете двигателя и отстранете

запалителния кабел преди ремонти или

техническо обслужване.

(Фиг. 6) Мерителна пръчка/маслен филтър

(Фиг. 7) Пазете се от отскачащи предмети и

рикошети.

(Фиг. 8) Предупреждение: въртящ се нож.

Осигурете пространство около ръцете и

краката си.

(Фиг. 9) Предупреждение: въртящи се части.

Осигурете пространство около ръцете и

краката си.

(Фиг. 10) Този продукт отговаря на изискванията на

приложимите директиви на EO.

(Фиг. 11) Шумови емисии в околната среда в

съответствие с Директивата на

Европейската общност. Емисиите на

продукта са посочени в раздела за

технически характеристики и на

табелката.

(Фиг. 12) Бързо.

(Фиг. 13) Бавно.

(Фиг. 14) Смукач.

(Фиг. 15) Риск от експлозия.

(Фиг. 16) Отработените газове от двигателя

съдържат въглероден окис – много

опасен, отровен газ без миризма. Не

20 808 - 004 -

Stránka sa načítava...

Husqvarna LC 247S Návod na obsluhu

Tento návod je vhodný aj pre

Husqvarna LC 247S Návod na obsluhu

v iných jazykoch

Súvisiace články

Ostatné dokumenty