1
GB
Contents
Important Information, 2-3
Installation, 4
Where to put your dryer
Ventilation
Electrical connection
Levelling the tumble dryer
Before you start using your dryer
Dryer Description, 5
Open the door
The Features
Control Panel
The Display, 6
Start and Programmes, 7-12
Choosing a Programme
Special Programmes
Table of Programmes
The Controls
Laundry, 13-14
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 15
General safety
Save energy and respect the
Environment
Maintenance and Care, 16
Switching off the electricity
Clean the filter after each cycle
Check the drum after each cycle
Empty the Water Container after each cycle
Cleaning the Heat Pump Filter
Cleaning the dryer
Troubleshooting, 17
Service, 18
Spare parts
Disposal
TUMBLE DRYER
AQUALTIS
AQC8 2F7
Instruction booklet
! This symbol reminds you to read this instruction manual.
! Keep this instruction booklet on hand in order to refer to it when
necessary. Take it with you when you move, and, should you sell this
appliance or pass it on to another party, make sure that this booklet
is supplied along with the dryer so that the new owner may be infor-
med about warnings and suggestions on how the dryer works.
! Read these instructions carefully; the following pages contain impor-
tant information on installation and suggestions on how the appliance
works
English,1
GB
PT BG
Português, 19
Български,37
ČČesky, 55
CZ
2
GB
Important Information
For your Condenser dryer to operate efficiently,
you must follow the regular maintenance schedule
shown below:
Fluff Filter – You MUST Clean the fluff filter after
every drying cycle.
Step 1
Open the door of your dryer.
Step 2
Pull out the filter (using the two
finger grips).
Step 3
Open the filter by releasing the
clip.
Step 4
Clean any fluff deposits from the
inside surface of the filter mesh.
Step 5
Refit the filter – Never run the
dryer without a filter.
Failure to clean the filter after every drying cycle will
affect the drying performance of your machine – It
will take longer to dry and as a result will use more
electricity during drying.
Water Container – You must empty the water
container after every drying cycle.
Step 1
Pull the water container
towards you and remove it fully
from the dryer.
Step 2
Empty the Water from the
Container.
Step 3
Refit the Water Container
ensuring that it is pushed fully
back into position.
Failure to empty the Water Container will result in:
- The machine will stop heating (so the load may be
wet at the end of the cycle).
- The ”Empty Water” light will flash to tell you that
the Container is full.
! The water bottle/clean filter
light comes on when you select
a programme to remind you to
make sure that the water bottle
is empty and that the filter is
clean before starting a new
cycle’
Priming the Water Collection System
When your dryer is new, the Water Container will not
collect Water until the system is primed, this will take
1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
2
3
GB
Step 5
Refit the filter unit - ensure that the unit is pushed in fully, then
turn all 4 clips into the horizontal position to lock the cover.
Failure to clean Heat Pump Filter will reduce the
drying performance and could cause premature
failure of your dryer.
To maintain optimum drying performance we
recommend you clean this filter after every drying
cycle.
Heat Pump Filter Unit - You must clean the fluff
from the filter every five drying cycles to maintain
the correct functioning of your dryer !
However for optimum performance and to save
energy we recommend that it is cleaned before
each drying cycle.
Step 1
Open the heat pump filter
Cover.
- hold the handle and pull
towards you.
Step 2
Remove the filter unit by
rotating the 4 clips to the
vertical position then pulling
the filter unit towards you.
(There may be some water in
the filter this is normal).
! Warning: The front of the heat pump is made from thin
metal plates.
Take care that you do not damage these or cut yourself
when cleaning, removing or replacing the filter unit.
Step 3
If there is any build up of
fluff on the plates Carefully
clean this off with a damp
cloth, sponge or vacuum
cleaner.
Never use your Fingers.
Step 4
Seperate the two parts of
the filter unit, clean any fluff
deposits from the inside
surface of the filter mesh.
Clean the seals.
Assemble the two parts.
Dados do Produto
Capacidade nominal para roupa de algodão para o "programa
normal de algodão" em plena carga - kg
8.0
Classe de eficiência energética A++
O consumo anual de energia ponderado (AEc)* Kwh 235.3
O secador de roupa para uso doméstico é Automático
O secador de roupa para uso doméstico é Por condens.
Consumo de energia com carga completa; Edry- kWh 1.99
Consumo de energia com carga parcial; Edry½,- kWh 1.07
Consumo de energia: estado de desativação (Po) - Watts 0.17
Consumo de energia: estado inativo (Pl) - Watts 3.73
Duração do "estado inativo" no sistema de gestão de energia -
minutos
30
Progr. Duração - plena carga e carga parcial ponderada (Tt) -
minutos
168
Plena carga (Tdry) - minutos 224
Carga parcial” (Tdry½) - minutos 126
Classe de eficiência de condensação B
Eficiência de condensação média - %
plena carga Cdr 82
carga parcial Cdry½ 81
plena carga e carga parcial ponderada (Ct) 81
Emissão de ruído aéreo - dB(A) re 1 pW 70
O programa normal de algodão** adequado para a secagem de roupa de algodão
húmida normal é o programa mais eficiente em termos de consumo de energia para
algodão em plena carga e carga parcial.
This is the test cycle in accordance with Regulation 392/2012.
http://www.hotpoint.eu/hotpoint/.
*Consumption per year is based on 160 drying cycles of the
standard cotton programme at full and partial load, and the
consumption of the low-power modes.
Actual energy con-
sumption per cycle will depend on how the appliance is used.
**The Standard Cotton Programme is Cottons Cupboard Dry
4
GB
Installation
Electrical connection
Before plugging the appliance into the socket, check the fol-
lowing:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand the machine’s maxi-
mum power output as indicated on the data plate (see Descrip-
tion of the tumble dryer).
• The power supply voltage must fall within the values indicated
on the data plate (see Description of the tumble dryer).
• The socket must be compatible with the machine’s plug. If
not, either the socket or the plug must be replaced.
! Do not use extension cords.
! The tumble dryer must not be installed in outdoor spaces,
even if sheltered. It may be very dangerous to expose this ap-
pliance to rain and thunderstorms.
! Once dryer installation is complete, the electric cord and plug
must be at hand.
! The electric cord must not be bent or crushed.
! If the plug to be replaced is of the moulded-on type, it must
be disposed of in a safe way. DO NOT leave it where it can be
plugged into a socket and cause electric shocks.{}
! The electric cord must be regularly checked and replaced
with a cord specifically designed for this dryer; it must then be
installed by an authorised technician only (see Assistance). New
or longer electric cords are supplied by authorised dealers at a
supplementary cost.
! The manufacturer declines all responsibility for failure to
observe these instructions.
a qualified electrician.
! If in doubt about any of the above consult a qualified
electrician.
Levelling the tumble dryer
The dryer must be installed level for correct operation.
When you have installed your dryer in its final location check
that it is level first side-to-side, then front to back. If the dryer is
not level, adjust the two legs up or down until your dryer is level.
Before you start using your dryer
Once you’ve installed your dryer and before you use it, clean
the inside of the drum to remove any dust that could have
accumulated during transportation.
Warning ! Before you use your dryer ensure that its has
been in a upright position for at least 6 hours.
Where to put your dryer
• Place your dryer at a distance
from gas ranges, stoves, heaters,
or cooktops because flames
can damage the appliance. The
dryer should be installed in an
ambient room temperature of
between 20 to 23°C for optimum
performance. But will function
if the room is between 14 and
30°C. If you are going to install the
appliance under a work counter,
be sure to leave a 10 mm space
between the top and any other objects on or above the
machine and a 15 mm space between the sides and lateral
furnishings or walls. This is to ensure proper air circulation.
.
Ventilation
• When the dryer is in use, there has to be adequate ventilation.
Make sure you put your dryer in an environment that is not damp
and has proper air circulation throughout. Airflow around the dryer is
essential to condense the water produced during the washing, the
dryer will not operate efficiently in an enclosed space or cupboard.
! If using the dryer in a small or cold room some
condensation will be experienced.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed behind a
lockable door, a sliding door or a door with a hinge on the
opposite side to that of the dryer door.
Water Drain
If the machine is positioned close to a drain it is possible to drain
the condensed water directly without using the waterbottle. In
which case it is no longer necessary to empty the water bottle at
the end of each cycle. If the Dryer is positioned above or close to
a Washing Machine the same drainage can be used. Just unlink
the tube indicated in figure A and connect it to the drainage.
If the drainage is further away than the length of the tube it is
possible to buy and connect a tube of the same diameter and
the necessary length in order to reach the drainage. To install the
new tube just substitute the existing one as indicated in figure B
inserting it in the same place.
! The drain tube has to be below 1 m from the bottom of
the Dryer.
! Once the Dryer has been installed please assure that
the drain tube is not bent or contorted.
10 mm
15 mm
15 mm
2
H<1m
2
Fig. A Fig. B
5
GB
To open door
Dryer Description
Control Panel
The On/Off button/light , if the dryer is running and this
button is pressed and held for more than 3 seconds the dryer
is turned off. The light signals that your dryer is in use or ready
to select a programme.
The Programmes knob sets the programme: rotate until the
indicator is pointing to the programme you want to select (see
Start and Programmes).
The Option buttons/ lights select available options for your
selected programme. The lights indicate that the option has
been selected (see Start and Programmes).
The Display Panel has three sections: Sensor Dry = Drying
level, Timed dry = Drying time and Time to End / Delay start
each with a corresponding selection button (see The Display).
START/PAUSE button with indicator light : when the
green indicator light flashes slowly, press the button to
start the programme. When the cycle has started, the
indicator light is illuminated in a fixed manner. To pause
the programme, press the button again; the indicator light
will turn orange and begin to flash again. To restart the
programme from the point at which it was interrupted, press
the button again (see Start and Programmes).
The Programme Progress Lights indicate each state of the
programme by turning on as appropriate.(see Start and
Programmes).
Note: this light also flashes amber during post care phase.
The Empty Water indicator “h2o” signals that the water
container should be emptied. The light will take a few seconds
to go out after replacing the empty water container; the dryer
must be running for this to happen (see The Controls).
Note: if the water bottle is full the display shows “h2o” and the
indicator flashes, the heat is turned off and your clothes will
not dry.
The Empty Water Clean Filter Light gives a reminder
before every programme, that its essential to clean the filter and
empty the water container every time the dryer is used (see
Maintenance and Care).
The Clean Heat Pump Filter Light gives a reminder, that its
essential to clean this filter at regular intervals (see Maintenance
and Care).
The Child Lock button/light Press and hold this button after
selecting your programme and any options. This prevents the
programme settings from being changed.
When the light is lit the other buttons and programme knob are
disabled. Hold the button to cancel and the light will go out.
ECO Light - this light is illuminated as you select options that
use less energy (see the controls).
The Features
Pull on handle
Water
container
Rating
Plate
Filter
Air Intake
Grille
Model
& Serial
Numbers
Heat Pump Filter
Unit
(cover open)
Heat Pump Filter Unit cover
handle
(Pull here to open)
Clean Heat
Pump
Filter
Ajustable feet
(to level dryer)
Option Buttons and Lights
On/Off Button & Light
Display Panel
Child Lock
Button & Light
Start/Pause
Button & Light
Programme
Progress Light
Programme Knob
Empty
Water /
Clean Filter
Light
ECO
Light
Sensor Dry
Timed Dry
Delay
Timer
6
GB
The Display
Timed Dry
After selecting a Programme that has a Timed Dry Option, press the Timed Button to select a drying time. The
display will reduce the selected time each time you press and release this button (see Start and Programmes).
Each press decreases the set time 220, 180, 150, 120, 90, 60, 40 and then repeats. If the Timed Dry option is
not available the display will flash and the buzzer beeps three times.The selected time remains displayed after the
programme starts and can be changed during the programme if you wish.
! You can either choose a sensor dry level or a drying time.
Delay Start
After selecting a Programme that has a Delay Start Option a delay start time can be selected.
Each press of the Delay start button advances the delay setting in 1 hour increments from “1h” to “24h” then
“OFF” and then after five seconds cancels the delay.
For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the display shows
“9:59” and then counts down in minutes. For delays of 9 hours or less the display shows hours and minutes and
then counts down in minutes for all of the delay.
After the Start/Pause Button is pressed the delay time can be changed or cancelled if you wish.
When the delay period finished the symbol is off and the Time to End is displayed.
If you have chosen a timed drying the display during programming will show the drying time only in the timed
drying display in the middle. After having pressed start the machine will turn the time display on and visualize
the countdown of the programme time.
Time to End
If the delay icon is off the time displayed is the Time to End of the programme running.
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When an Automatic programme is selected the time displayed is an estimate of the time remaining.
When the programme is selected the display shows the time required to dry a full load. The remaining time is
constantly monitored during the drying cycle and is updated to show the best forecast.The time to end is
displayed in hours and minutes and counts down each minute.
The colon between the hours and minutes display flashes to show that the time is counting down.
The Display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a
fault code number, the four option lights and the pause light will also flash Orange
(see Troubleshooting).
The Display has three sections each with its corresponding button.
Sensor Dry
After selecting a programme that has a Sensor Dry Option, press and release the button until the required dryness
sensing level is displayed. If the sensing option is not available the display will flash and the buzzer beeps three
times.
! Some drying programmes are not compatible with all 7 sensor drying levels.
Dryness levels available
Damp dry: the most delicate level which makes sure that your clothes are not dripping wet. After a
hand-wash the perfect level to then hang your clothes if you do not want to tumble dry them all the way to
the end.
Iron Dry: a very delicate drying, It is useful for garments you would like to iron afterwards.
Hanger plus: just the drying status to hang delicate garments up (as curtains).
Hanger Dry: just the drying level to hang the garments up.
Light dry: ideal for delicate clothes to be folded and placed into the cupboard.
Cupboard Dry: the garments are completely dry and are ready to be folded and placed in the cupboard.
Ready to Wear: used for clothes to be worn straight away once the cycle is completed.
7
GB
Start and Programmes
Choosing a Programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see Laundry).
3. Open the door and make sure the filter is clean and in place
and the water container is empty and in place (see Maintenance).
4. Load the machine and make sure that the items are not in
the way of the door seal. Close the door.
5. If the ON/Off light is not lit; press the On/Off Button .
6. Select the Programmes selection that corresponds with
fabric being dried by checking the Programmes table (see
Programmes) as well as the indications for each type of
fabric (see Laundry).
7. Where available, choose Sensor Dry or Timed Dry
option pressing and releasing the corresponding button until
the desired level or time is displayed.
! See programmes table, for more details.
8. Set a delay time and other options as necessary (see The Display).
9. If you wish the buzzer to sound at the end of the
programme, press the sound button . If you have selected
the Crease Care option, this option is not available.
10. Press the START button to begin. The display will
show the estimated time to end.
During the drying programme, you can check on your
laundry and take out the items that are dry while the others
continue drying. When you close the door again, press
Special Programmes
Easy Iron Programme
Easy Iron is a short 10 minute programme (8 minutes of heat followed by a 2 minutes cool tumble period) which fluffs the fibres of
clothing that has been left in the same position/location for an extended period of time. The cycle relaxes the fibres and makes them
easier to iron and fold.
! Easy Iron is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than maximum capacity. These numbers refer to dry weight:
Fabric: Max
Cotton and Cotton mix 2.5 kg
Synthetics 2
Denim 2
2. Unload the dryer immediately after the end of the drying cycle, hang, fold or iron the articles and put them away in the closet.
Should this not be possible, repeat the cycle.
The Easy Iron effect varies from one fabric to the next. It works very well on traditional fabrics like Cotton or Cotton mix, and less
well on acrylic fibres and on materials such as Tencel.®
Wool Programme
• This is a programme for tumble dryer safe garments marked with the symbol .
• It can be used for load sizes up to 1 kg (approximately 3 sweaters).
• We recommend that garments are turned inside out before drying.
• Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be slightly
damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and shape.
! This program is not suitable for Acrylic garments.
Jeans
• This is a programme for Jeans made from Denim Cotton. Before drying your Jeans turn the front pockets inside out.
• It can be used for load sizes up to 3 kg (approximately 4 pairs).
• It can also be used on other garments made from same material such as jackets.
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try turning
the jeans inside out and running the programme again for a short period.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
• Use this cycle only for a 100% cotton load, do not mix dark and light coloured items. Do not use this cycle for garments with
embroidery and accessories (pins,...), turn the pockets insideout
! We do not recommend that you use this programme if your jeans have elastic waist bands or embroidery.
START in order to resume drying.
If you open the door to check your laundry you will extend the
drying time as the heat pump compressor will not start until 5
minutes after you close the door and pressed the start Button
(see The Controls).
11. During the last few minutes of Drying Programmes before
the programme is completed, the final COOL TUMBLE phase
is entered (fabrics are cooled), this phase should always be
allowed to complete.
12. To let you know that your programme is complete the
buzzer will beep 3 times and the display shows END (Note:
if the SOUND option was selected the buzzer beeps 3 times
every 30 seconds for 5 minutes).Open the door, take your
laundry out, clean the filter and replace it. Empty the water
container and replace it (see Maintenance).
If the Crease Care option has been selected and you do
not take the clothes out immediately the clothes will tumble
occasionally for 10 hours or until you open the door.
13. Switch dryer off using the On/Off button.
Standby mode
This tumble dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system which is
enabled after about 30 minutes if no activity is detected. Press
and hold the On-Off button until the dryer reactivates.
8
GB
Special Programmes
Shirts
High Heat option
• This is a programme for Shirts made from Cotton.
• It can be used for load sizes up to 3 kg (approximately 12 shirts).
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try
turning the shirts inside out and running the programme again for a short period.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used inyour
washer.
Low Heat option
• This is a programme for Shirts made from synthetic materials or a mixture of natural and synthetics materials such as
Polyester and Cotton.
• It can be used for load sizes up to 3 kg (approximately 12 shirts).
• Loads dried using this programme are usually ready to wear; the edges or seams may be slightly damp. If this is found try
turning the shirts inside out and running the programme again for a short period.
Note: The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
Silk
• This is a programme for drying your Delicate Silk.
• It can be used for load sizes up to 0.5 kg.
• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If this
is found try removing the load and open them out then run the programme again for a short period.
• Only for garments labelled suitable for tumble drying.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
Duvet programmes
! Take care with these programme do not dry any items that are damaged which could result in the filling blocking the filter
and air path resulting in a fire hazard.
• Must only be used on Single size duvets not suitable for double or king size items.
• Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is found try removing
the load and open them out and shake then run the programme again for a short period.
• Also suitable for down filled jackets.
Note: The duration of this programme will depend on the size of the load and the spin speed used in your washer.
Duvet - High Heat option
• This is a programme for drying your Cotton Duvets. With Cotton outer cover and down filling.
• Only for garments labelled suitable for tumble drying.
Duvet - Low Heat option
• This is a programme for drying your Synthetic Duvets, with synthetic filling.
• Only for garments labelled suitable for tumble drying.
Baby Delicate
• This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille) and for drying your
Delicate Clothes.
• Do not dry items such as bibs and nappy pants with plastic coverings.
• It can be used for load sizes up to 2 kg.
• Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be slightly damp. If
this is found try turning them inside out and running the programme again for a short period.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
Bed & Bath
• This is a programme for Cotton Towels and sheets.
• It can be used for load sizes up to 8 kg.
• Loads dried using this programme are usually ready to use; the edges or seams may be slightly damp especially on large
items. If this is found try opening them out and running the programme again for a short period.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
9
GB
Refresh
Thanks to a cool air flow, oxygen penetrates the fibers and transports unpleasant odors such as cigarette smoke, frying, smog out
of the clothes. With this short program, you can easily refresh your garments in just 20 minutes.
! Airing is not a drying programme and should not be used for wet articles of clothing.
• If can be used on any load size up to 8 kg, but is more effective on smaller loads.
20-minute programme that airs your clothes with cool air. Use also to cool warm clothes.
Anti Allergy
The programme has the ‘Seal of Approval’ endorsement from ‘Allergy UK’, which reflects the effective reduction and elimination of
allergens from the clothes. With this programme, thanks to the achievement of constant temperature for an extended period of time,
the effects of the most common allergens (including House Dust Mite and Pollen) are neutralized.
Can be used on wet load to dry and treat or on a dry load just to treat your laundry.Maximum load is 9 kg for a wet load and 4 kg for
a dry load.
Quick Dry
• Your drying time for small loads is very much reduced with a huge time saving up to 25% on cottons (with High Heat option) and
39% on synthetics (with Low Heat option).
Load: 1 Kg. Dryness level: only Cupboard Dry
Activewear
• This programme is specific for drying water-repellent fabrics and sports jackets (e.g. Gore-Tex, polyester, nylon). Drying the
garment after a wash cycle has a beneficial effect as it reactivates the garment’s water-repellent treatment.
It can be used for loads of up to 2 kg. Dryness level: only Cupboard Dry
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
Heat & Enjoy
• The Heat & Enjoy cycle helps to heat towels & bathrobes for a warm sensation after a bath or a shower. It is also useful for
warming clothes before dressing during winter.
The cycle heats the clothes up to 37° (the body temperature) and keeps the same temperature for a maximum of 4 hours or until
the user stops the cycle by opening the door.
Load: 3 Kg.
!Note: during this programme a icon rotates in the display until the temperature target is reached at which point the dryness
level icon flashes.
Dark Cycle
This programme helps to maintain the your Dark coloured clothes, by controlling the motor speed and drum rotation together with
control of the lower drying temperature.
• It can be used on cottons and jeans load size up to maximum of 3 kg, but is more effective on smaller loads.
• The duration of this programme will depend on the size of the load, the dryness setting selected and the spin speed used in
your washer.
10
GB
Programmes Table
! If the On/Off light is not lit; Press the On/Off Button and then select programme.
Programme What it does How to set it Notes / Options available
Easy Iron
Brief programme (approxima-
tely 10 minutes) that softens
fibres of clothing that is ready
for ironing.
1. Position the PROGRAMME knob on
.
2. Select Alarm Option if required.
3. Press the Start Button .
! This is not a drying programme (see previous page).
Options available
Sound
.
Refresh
20 min cool programme to air
your clothes
1. Position the PROGRAMME knob on
.
2. Select Alarm Option if required.
3. Press the Start Button .
Sound
.
Cottons
Dries: your Cotton clothes.
N.B: Max. load 6 kg (with
Low Heat option)
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
or Crease care . Delay Start . High Heat
Less Fluff .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry , Ready to Wear *.
Shirts
Dries your shirt.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button
.
Sound
or Crease care . Delay Start . High Heat
. Less Fluff .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
Jeans
Dries denim clothes.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
or Crease care . Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry , Ready to Wear *.
Synthetics
Dries: your synthetics clothes.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
or Timed Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
or Crease care . Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
Bed & Bath
Dries your Towels and
bedding.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
or Crease care . Delay Start . Less Fluff
.
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry , Ready to Wear *.
(We suggest to use only Cupboard dry)
Duvet
Dries your Duvet.
1. Position the PROGRAMME knob on .
2. Select any Options if required.
3. Press the Start Button .
Sound or Crease care . Delay Start . High Heat
.
Wool
Dries: your Woollen clothes.
1. Position the PROGRAMME knob on
.
2. Select any Options if required.
3. Press the Start Button .
Sound
.
Silk
Dries your silk items.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
(see next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
.
Sensor Dry option, automatic drying:
Damp dry
, Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
(We suggest to use only Cupboard dry)
Baby
Delicate
Dries your baby clothes.
1. Position the PROGRAMME knob on
.
2. Choose Sensor Dry
or Timed Dry (see
next page).
3. Select any Options if required.
4. Press the Start Button .
Sound
or Crease care . Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger dry
, Light dry , Cupboard dry .
(We suggest to use only Cupboard dry)
Anti Allergy
Anti Allergy treatment for your
cotton clothes.
1. Position the PROGRAMME knob on
.
2. Select any Options if required.
3. Press the Start Button .
Sound
or Crease care . Delay Start .
* just with High Heat option on
11
GB
Sensor Drying and Timed Drying
First select a programme (see programmes table).
! For the best performance do not open the door before the cycle has finished.
Programme What it does How to set it Notes / Options available
Dark Cycle
Dries your dark clothes.
1. Position the PROGRAMME knob on
.
2. Select any Options if required.
3. Press the Start Button .
Sound
. Delay Start .
Sensor Dry option, automatic drying:
Damp dry , Iron dry , Hanger Plus , Hanger
dry , Light dry , Cupboard dry .
(We suggest to use only Cupboard dry)
Quick Dry
Dries your cotton or synthetic
clothes in less time.
1. Position the PROGRAMME knob on
.
2. Select any Options if required.
3. Press the Start Button .
Sound
or Crease care . Delay Start . High Heat
Activewear
Dries your sports clothes.
1. Position the PROGRAMME knob on
.
2. Select any Options if required.
3. Press the Start Button .
Sound
or Crease care . Delay Start .
Heat & Enjoy
Heats your towel & bathrobe.
1. Position the PROGRAMME knob on
.
2. Press the Start Button .
-
Programme What it does How to set it Notes / Options available
Sensor
Drying
Always use Sensor Dry if pos-
sible for drying your clothes. It
will guarantee you best drying
results.
The heat setting depends
on the programme (material
option) selected.
1. Press and release the sensor Dry button until
the display shows the desired selection. Each
press advances
, , , , , , and
then repeats.
! Some sensing programmes do not have all 7
dryness level options.
2. Select any Options if required.
3. Press the Start Button .
Options available
Sound
or Crease care . Delay Start .
High Heat
. Less Fluff .
Consult suggested drying times (see Laundry).
The last few minutes of these programmes is the cool
tumble phase.
Timed
Drying
(220, 180,
150, 120,
90, 60 or 40
minutes)
Always use timed drying
option if you want to decide
the drying time.
The heat setting depends
on the Programme (material
option) selected.
1. Press and release the Timed Button until the
display shows the required selection. Each
decreases time 220’, 180’, 150’, 120’, 90’,
60’, 40’ and then repeats.
• Baby Delicates have a maximum time of 180’.
2. Select any Options if required.
3. Press the Start Button
.
Options available
Sound
or Crease care . Delay Start . High
Heat
.
Consult suggested drying times (see Laundry).
The last few minutes of these programmes is the cool
tumble phase.
12
GB
The Controls
• Programme knob
! Warning, if after pressing the start button the programme
knob position is changed, the new position will NOT change
the programme selected.
To change programme press Start/Pause Button to pause
the programme, the light flashes Amber, select new programme
and any option, the light will then flash green. Press the Start/
Pause Button and the new programme will start.
• Option Buttons/ Lights
These buttons are used to customise the selected
programme to your requirements. Not all options are
available for all programmes (see Start and Programmes).
If an option is not available and you press the button, the
buzzer will beep three times. If the option is available the
option light next to the button lights to confirm the selection.
• ECO Light
This light is illuminated when you select programme options
that will use less energy than the default setting. Examples
are if you choose an Automatic or sensing programme or
use a timed dry setting less than the default time. This light
does not indicate that the optimum setting for energy use
has been selected; it only shows you that your selected
options will use less energy.
• Progress ( Drying, Cool tumble, ) Lights
The Progress lights show you the status of the programme. At
each stage of the programme the corresponding light turns on.
• Delay Start
The start of some programmes (see Start and Programmes)
can be delayed for up to 24 hours (see The Display).
Ensure the water bottle is emptied and the filter is cleaned
before setting a delayed start.
• Less Fluff
By reducing the mechanical action during the final drying
stage the amount of lint and fluff produced is substantially
reduced protecting the fibres of your garments. Note: For
Shirts programme, if you have selected Low Heat option,
this option is not available.
• Sound
A buzzer sounds at the end of the drying cycle to signal that
the programme has ended and the garments are ready to be
removed. Note: If you have selected the Crease Care option,
this option is not available.
• Crease Care
When a delayed start and this option have been selected the
clothes are tumbled occasionally during the delayed period
to help prevent creases developing.
After end of the drying and cool tumble cycles, the clothes
are occasionally tumbled to help prevent creases developing,
should you not be available to remove the load immediately
after the programme is complete. The light is on during
this phase after end of the cycle and the start/pause light
flashes amber. flashes amber. Note: If you have selected the
Sound option, this option is not available.
• High Heat
When a drying time is selected, pressing this button sets
a high heat drying and the indicator light above the button
lights up.
• Empty Water Clean Filter Light “h2o”
(If you have plumbed your dryer to a drain the light can be
ignored for the water bottle, as there is no need to empty the
water container). When is on (not flashing) it reminds you to
empty the water container. If the water container fills during a
programme, the heater turns off and the dryer does a period
of Cool Tumble then the light flashes and the buzzer sounds.
You must empty the container and restart the dryer or the
clothes will not dry. After re-starting the dryer the light will take
a few seconds to go out. To avoid this always empty the water
container each time you use the dryer (see Maintenance).
! Please note that you ALWAYS have to clean the filter even if
you have plumbed your dryer to a drain.
• Door Opening
Opening the door (or pressing the Start/Pause Button) during a
programme will stop the dryer and have the following effects.
Note: The Start/Pause Light flashes Amber during the Post
Care phase of a programme.
• During a delay phase the delay will continue to count
down. The start button must be pressed to resume the
delay programme. One of the delay lights will flash to
show the current delay setting.
• The start button must be pressed to resume the
programme. The progress lights will change to show the
current status and the Start/Pause light will stop flashing
and turn green.
• During the post creasecare phase of a drying program,
the Programme will finish. Pressing the Start/Pause
button will restart a new program at the beginning.
• Changing the Programmes knob will select a new
programme and the Start/Pause Light will flash green.
You can use this to select the “Refresh” programme to
cool the clothes if you find them dry enough. Pressing the
start/pause button to begin new Programme.
• Heat Pump Protection System
The heat pump sytem has a compressor protection
feature, that operates if you open the door or there is a
power disruption or you turn off the dryer. This system
will prevent the heat pump compressor from starting for
5 minutes after the door is closed and the programme
started.
• Note
If you have a power cut, switch off the power or remove
the plug. When power is restored, plug in the machine,
press and hold the ON/OFF button until the dryer
reactivates, then press Start/Pause button.
13
GB
Laundry
Sorting your laundry
• Check symbols on clothing labels to make sure that the
articles can be tumble dried.
• Sort laundry by fabric type.
• Empty pockets and check buttons.
• Close zippers and hooks and tie loose belts and strings.
• Wring out each item in order to eliminate as much
excess water as possible.
! Do not load dripping wet clothes into the dryer.
Maximum load
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 8 kg max (17.6 lb)
Synthetic fibres: 3 kg max (6.6 lb)
! Do not overload the dryer as this could result in reduced
drying performance.
Typical weights
Note: 1kg = 1000g; (1 lb = 16 oz.)
At the end of a drying cycle, cottons could still be damp if
you grouped cottons and synthetics together. If this happens
simply give them an additional short period of drying.
Clothes
Blouse
Dress
Jeans
10 Nappies
Shirt
T - Shirt
Cotton
Other
Cotton
Other
Cotton
Other
150g (5 oz)
100g (3 oz)
500g (1lb 2 oz)
350g (12 oz)
700 g (1 lb 6 oz)
1000 g (2 lb 6 oz)
300g (10 oz)
200g (7 oz)
125 g (4 oz)
Household items
Duvet cover
(Double)
Large Tablecloth
Small Tablecloth
Tea Towel
Bath Towel
Hand Towel
Cotton
Other
1500g (3 lb 5 oz)
1000g (2 lb 3 oz)
700 g (1 lb 6 oz)
250 g (9 oz)
100 g (3 oz)
700 g (1 lb 6 oz)
350 g (12 oz)
Double Sheet
500 g (1 lb 2 oz)
350 g (12 oz)
Single Sheet
Wash care labels
Look at the labels on your garments, especially when tumble
drying for the first time. The following symbols are the most
common:
May be tumble dried.
Do not tumble dry.
Tumble dry at high heat setting.
Tumble dry at low heat setting.
What not to tumble dry in your dryer:
• Articles that contain rubber or rubber-like materials, or
plastic film (pillows, cushions, or PVC rainwear); any other
flammable objects, or objects that contain flammable
substances (towels soiled with hairspray).
• Glass fibres (certain types of draperies).
• Items that have been Dry Cleaned.
• Items with the ITLC code (“Special clothing items”) .
These can be cleaned with special at-home dry cleaning
products. Follow instructions carefully.
• Large bulky items (pillows, cushions and large
bedspreads. Sleeping bags and duvets can be dried
using the Duvet programmes as described on page 8).
These expand when drying and would prevent airflow
through the dryer.
IT
1
The wool drying cycle of this
tumble drying machine has
been tested and approved
by The Woolmark Company.
The cycle is suitable to dry
wool garments which are
labeled “hand wash” provided that the garments are washed
in a Woolmark endorsed hand washing cycle and tumble
dried according to the instruction issued by the manufactu-
rer. M1219.
In UK, Eire, Hong Kong and India the Woolmark symbol is a
certification trademark.
14
GB
Cotton
High Heat
1 kg 2 kg 3 kg 4 kg 5 kg 6 kg 7 kg 8 kg
Automatic
minutes
35-60 55-90 85-100 100-130 130-150 160-180 200-210 210-230
Timed
40 or 60 60 or 90 90 or 120 90 or 120 120 or 150 150 or 180 180 180 or 220
Drying times 800-1000 rpm in washing machine
Synthetics
Low Heat
1 kg 2 kg 3 kg
Automatic minutes
40-50 50-60 60-90
Timed Dry setting
40 or 60 40 or 60 60 or 90
Drying times on reduced spin in washing machine
Acrylics
(Delicates)
Low Heat
1 kg 2kg
Timed dry only
30 60
Drying times on reduced spin in washing machine
Special clothing items
Blankets and bedspreads: acrylic items (Acilian, Courtelle,
Orion, Dralon) must be dried with special care on a low heat
setting. Avoid drying for a long period of time.
Pleated or creased garments: read manufacturer drying
instructions on the garment.
Starched articles: do not dry these items with nonstarched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in the
dryer. Do not over-dry: the starch will become powdery
and leave your clothing limp, which defeats the purpose of
starch.
Drying times
Times are approximate and can vary depending upon:
• Amount of water retained in clothes after spin cycle:
towels and delicates retain a lot of water.
• Fabrics: items that have the same type of fabric but
different textures and thicknesses may not have the
same drying times.
• Quantity of laundry: single items or small loads may
take longer to dry.
• Dryness: if you are going to iron some of your clothes,
they can be taken out while still a bit damp. Others can
be left longer if you need them to be completely dry.
• Heat setting.
• Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to dry your
clothes.
• Bulk: some bulky items can be tumble dried with care.
We suggest that you remove these items several times,
shake them out, and return them to the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which keeps them
soft and fluffy.
The table below presents APPROXIMATE drying times:
the times given are for Cupboard Dry Automatic programmes.
Timed dry settings are also shown, to help choosing a suitable
time option.
Weights refer to dry garments.
Drying times
15
GB
Warnings and
Suggestions
! This appliance has been designed and built according to
international safety standards. These warnings are given for
safety reasons and must be followed carefully.
General safety
• This tumble dryer is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities , or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for there safety.
• This tumble dryer has been designed for home, and not
professional, use.
• Do not touch the appliance while barefoot or with wet
hands or feet.
• Unplug the machine by pulling on the plug, not the cord.
• Children must not be in proximity of the dryer when in
use. After using the dryer, turn it off and unplug it. Keep
the door closed to make sure that children do not use it
as a toy.
• Children should be supervised to ensure that they do
not play with the dryer.
• The appliance must be installed correctly and have
proper ventilation. The air intake at the front of the
dryer should never be obstructed (see Installation).
• Never use the dryer on carpeting where the pile height
would prevent air from entering the dryer from the base.
• Check to see if the dryer is empty before loading it.
• The back of the dryer could become very hot.
Never touch it while in use.
• Do not use liquid fabric softeners in the dryer; add it to
the final rinse of your wash.
• Do not overload the dryer (see Laundry for maximum
loads).
• Do not load items that are dripping wet.
• Carefully check all instructions on clothing labels (see
Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high temperatures.
• Complete each programme with its cool tumble phase.
• Do not turn off the dryer when there are still warm items
inside.
• Clean the filter after each use (see Maintenance).
• Empty the Water Container after each use (see
Maintenance).
• Clean the Heat Pump filter unit at regular intervals (see
Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could result in damage.
• Always follow electrical standards and requirements (see
Installation).
• Always buy original spare parts and accessories (see
Service).
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
To minimise the risk of fire in your tumble dryer, the
following should be observed:
• Tumble dry items only if they have been washed with
detergent and water, rinsed and been through the spin cycle.
It is a fire hazard to dry items that HAVE NOT been washed
with water.
• Do not dry garments that have been treated with chemical
products.
• ●Do not tumble dry items that have been spotted or soaked
with vegetable or cooking oils, this constitutes a fire hazard.
Oil-affected items can ignite spontaneously,especially when
exposed to heat sources such as a tumble dryer. The items
become warm, causing an oxidisation reaction with the oil,
Oxidisation creates heat. If the heat cannot escape, items
can become hot enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat from escaping
and so create a fire hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or those that have been
contaminated withhair care products be placed in a tumble
dryer they should first be washed with extra detergent - this
will reduce, but not eliminate the hazard. The cool tumble
phase should be used to reduce the temperature of the
items. They should not be removed from the dryer and piled
or stacked while hot.
• ●Do not tumble dry items that have previously been cleaned
in or washed in, soaked in or soiled with petrol/gasoline,
dry cleaning solvents or other flammable or explosive
substances. Highly flammable substances commonly used
in domestic environments including cooking oil, acetone,
denatured alcohol, kerosene, spot removers, turpentine,
waxes and wax removers. Ensure these items have been
washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
• Do not tumble dry items containing foam rubber (also known
as latex foam), or similarly textured rubber like materials.
Foam rubber materials can, when heated, produce fire by
spontaneous combustion.
• Fabric softener or similar products should not be used in
a tumble dryer to eliminate the effects of static electricity
unless the practice is specifically recommended by the
manufacturer of the fabric softener product.
• ●Do not tumble dry undergarments that contain metal
reinforcements eg. bras with metal reinforcing wires.
Damage to the tumble dryer can result if the metal
reinforcements come loose during drying.
• ●Do not tumble dry rubber, plastic articles such as shower
caps or babies waterproof covers, polythene or paper.
• ●Do not tumble dry rubber backed articles, clothes fitted with
foam rubber pads, pillows, galoshes and rubber coated
tennis shoes.
• ●Remove all objects from pockets, especially lighters (risk of
explosion).
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
16
GB
Maintenance and Care
Switching off the electricity
! Unplug the dryer when not using it, when cleaning it, and
during maintenance activities.
Clean the filter after each cycle
The filter is an important part of your dryer: it accumulates
lint and fluff that is formed while drying.
When finished drying, clean the filter by rinsing it under
running water or with your vacuum cleaner. Should the
filter become clogged up, the airflow inside the dryer will be
seriously compromised: drying times lengthen and you will
consume more energy. It may also damage your dryer.
The filter is found in front of the dryer trim (see diagram).
Removing the filter:
1. Pull the plastic grip of the
filter upwards (see diagram).
2. Open the filter by
depressing the clip.
3. Clean the lint from the
inside of the filter, and
replace it correctly. Ensure
the filter is fully located flush
into the tumble dryer trim.
! Do not use dryer without replacing the filter.
Check the drum after each cycle
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Cleaning the drum
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless steel
drum, this may be caused by a combination of water
and, or cleaning agents such as fabric conditioner from
the wash. This coloured film will not affect the dryer
performance.
Empty the Water Container after each cycle
Pull the container out of the dryer and empty it into a sink or
other suitable drain. Replace container securely.
Always check and empty the container before you start a new
drying programme.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove Heat pump
filter unit and clean any build up of fluff from the
surface of the filter by rinsing it under running water or with
your vacuum cleaner.
We however recommend that you clean this filter after
every drying cycle to optimize the dryers performance.
To remove Heat pump filter unit:
1. Unplug the dryer and open the door.
2. Remove the filter unit by rotating the 4 clips to the vertical
position then pulling the filter unit towards you.
3. Separate the two parts of the filter unit
and clean the surface of the filter.
! Warning: The front of the heat pump
is made from thin metal plates.
Take care that you do not damage these
or cut yourself when cleaning, removing
or replacing the filter unit.
4. If there is any build up of fluff on the
plates Carefully clean this off with a
damp cloth,sponge or vacuum cleaner. Never use your Fingers.
5. Assemble the two parts of the filter clean the surface of the
seals and replace with the 4 clips into the horizontal position,
sure that the catches have been secured.
Cleaning the dryer
• External parts in metal or plastic and rubber parts can
be cleaned with a damp cloth.
• Periodically (every 6 months) vacuum the front Air intake
grille, to remove any build up of fluff, lint or dust. Also to
remove accumulation of fluff from the front of Heat Pump filter
unit and filter areas, clean occasionally with a vacuum cleaner.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which do not
need lubrication.
! Have your dryer checked regularly by authorized technicians
to ensure electrical and mechanical safety (see Service).
Water Contaniner
Catches
Filter
Handle
Air Intake
Heat Pump
Filter Unit
Heat Pump Filter
Unit Cover
17
GB
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troublesho-
oting suggestions.
Possible causes / Solutions:
• The plug is not plugged into the socket, or not making contact.
• There has been a power failure.
• The fuse has blown. Try to plug another appliance into the socket.
• You are using an extension cord. Try to plug the dryer’s power cord directly into the
socket.
• The door is not closed securely.
• The programme has not been set properly (see Start and Programmes).
• The START button has not been pressed (see Start and Programmes).
• You have set a delay time (see Start and Programmes).
• You have pressed the start button; there will be a short delay before the dryer starts.
Wait for drying to begin,do not press the start button again or the dryer will pause
and not begin drying.
• The filter has not been cleaned (see Maintenance).
• The water container needs emptying? The empty water
light is flashing and “h2o”
message is displayed?
(see Maintenance).
• The Heat Pump Filter needs cleaning (see Maintenance).
• The temperature setting is not ideal for the type of fabric you are drying (see Start and
Programmes, and Laundry).
• The correct drying time has not been selected for this load (see Laundry).
• The air intake grille is obstructed (see Installation and see Maintenance).
• The items are too wet (see Laundry).
• The dryer is overloaded (see Laundry).
• The water container was probably not emptied at the start of the programme. Do
not wait for the empty water signal always check and empty the container before
starting a new drying programme (see Maintenance).
• This is normal the empty water flashes when the container is full. If the light is on but not
flashing its just a reminder to empty the container (see Start and Programmes).
! For safety the dryer has a maximum programme time of 5 hours. If an automatic
programme has not sensed the required final moisture in this time the dryer will
complete the programme and stop. Check the above points and run the programme
again, if the results are still to damp, contact the service centre (see Service).
• If the display shows F followed by one or two numbers, Turn off and remove plug,
Clean the Filters (see Maintenance). Then replace plug turn on and start another
program.
If the number is displayed again Note down the number and contact the service
centre (see Service).
• The dryer is in ‘Demo’ mode. Press and hold both the On/Off and Start/Pause
buttons for 3 seconds. The display will show “dOn” for 3 seconds and then the
dryer will resume normal operation.
• The time to end is continuously monitored throughout the drying cycle and the time
is adjusted to give the best-estimated time. The displayed time may increase during
the cycle and this is normal.
• This is normal, particularly if the dryer has not been used for a while. If the noise
persists throughout the whole drying cycle then contact the service centre.
• The dryer has gone into standby mode to save power. This occurs if you have left the
dryer on or have had a power cut. It occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Press and hold the ON/OFF button until the dryer reactivates
Problem:
The dryer won’t start.
Drying cycle will not begin.
It is taking a long time to dry.
The Empty water light is flashing
but the dryer has only been running
for a short period.
Empty water light is on and the
water container is not full.
Programme finishes and clothes
damper than expected.
The Display shows a fault code F
followed by one or two numbers,
the option lights and pause light are
flashing.
The display briefly shows “dOn”
every 6 seconds.
Time to End display changes during
drying.
The dryer makes a thumping noi-
se during the first few minutes of
operation.
The lights on the dryer control
panel are off although the dryer is
switched on.
Troubleshooting
18
GB
Service
Heat Pump System
This dryer is fitted with a sealed heat pump system to dry
your clothes. To operate, the heat pump contains fluorinated
greenhouse gases ( F gases) which are covered by the Kyoto
Protocol. These F gases are contained in a hermetically
sealed unit. This sealed unit contains 0.30 kg of the F gas
R134a which acts as a refrigerant.
If the sealed unit fails then it must be replaced by a new
sealed unit. Contact your nearest service centre for advise.
Note: The gases contained in the sealed unit are not
hazardous to health, but if they escape they will have an
impact on global warming.
Before calling the Service Centre:
• Use the troubleshooting guide to see if you can solve
the problem yourself (see Troubleshooting).
• If not, turn off the dryer and call the Service Centre
closest to you.
What to tell the Service Centre:
• Name, address, and post code;
• telephone number;
• the type of problem;
• the date of purchase;
• the appliance model (Mod.);
• the dryer serial number (S/N).
This information can be found on the data label inside the door
of the machine.
Spare Parts
This dryer is a complex machine. Repairing it yourself or having
a nonauthorised person try to repair it could cause harm to one
or more persons and to the machine, and could invalidate the
spare parts warranty.
Call an authorised technician if you experience problems while
using the machine.
Please note that it is an offence for an unqualified person to
undertaken any servicing or repair work that involves breaking
into the sealed heat pump unit.
This appliance conforms to the following EC directives:
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (Electromagnetic Compatibility Directive).
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components to
reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the applian-
ce. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
The European Directive 2012/19/EC on Waste Electricaland Electronic Equipment (WEEE), requires that oldhousehold
electrical appliances must not be disposedof in the normal unsorted municipal waste stream. Old appliances must be
collected separately in order tooptimise the recovery and recycling of the materialsthey contain and reduce the impact on
human healthand the environment. This dryer has a sealed heat pump unit containing Fgases which should be recovered and
destroyed.The crossed out “wheeled bin” symbol on theproduct reminds you of your obligation,thatwhen you dispose of the
appliance it must beseparately collected.Consumers should contact their local authority orretailer for information concerning the
correct disposalof their old appliance.
PT
19
Português
Índice
Informações importantes, 20-21
Instalação, 22
Onde instalar a máquina de secar roupa
Ventilação
Descarga da água
Ligação eléctrica
Nivelamento da máquina de secar roup
Informações preliminares
Descrição da máquina de secar roupa, 23
Abertura da porta
Características
Painel de comandos
Visor, 24
Início e programas, 25-30
Selecção do programa
Programas especiais
Tabela dos programas
Comandos
Roupa, 31-32
Triagem da roupa
Etiquetas de manutenção
Peças especiais
Tempos de secagem
Advertências e sugestões, 33
Segurança geral
Eliminação
Economia energética e respeito pelo meio ambiente
Cuidados e manutenção, 34
Interrupção da alimentação eléctrica
Limpeza do filtro no fim de cada ciclo
Controlo do tambor no fim de cada ciclo
Esvaziamento do recipiente de recolha da água no fim de
cada ciclo
Limpeza do filtro da Bomba de Calor
Limpeza da máquina de secar roupa
Problemas e soluções, 35
Assistência, 36
Eliminação
PT
AQUALTIS
AQC8 2F7
Instruções para a
utilização
MÁQUINA DE SECAR ROUPA
! Mantenha o presente manual num local acessível para poder
consultá-lo facilmente sempre que necessário. Mantenha sempre o
manual junto da máquina de secar roupa. Se a máquina for vendida
ou cedida a outras pessoas, faça-a acompanhar deste manual, para
que os novos proprietários possam conhecer as advertências e
sugestões relacionadas com a utilização da mesma.
! Leia com atenção estas instruções: as páginas seguintes contêm
informações importantes sobre a instalação e sugestões úteis sobre
o funcionamento do electrodoméstico.
20
PT
A falta de limpeza do filtro no fim de cada ciclo de secagem
tem influência sobre os desempenhos da máquina, que
demora mais tempo a secar e, consequentemente,
consome mais electricidade durante a secagem.
Recipiente de recolha da água – É necessário
esvaziar o recipiente de recolha da água no fim de
cada ciclo de secagem.
Fase 1
Puxe o recipiente de recolha da
água em direcção a si e retire-o
completamente da máquina de
secar roupa.
Fase 2
Esvazie toda a água contida no
recipiente.
Fase 3
Reinstale o recipiente de recolha
da água, certificando-se de que
fica completamente inserido na
respectiva posição.
O não esvaziamento do recipiente de recolha da
água pode causar:
- A paragem do aquecimento da máquina (o que
faria com que a roupa continuasse húmida no fim
do ciclo de secagem).
- O indicador luminoso “Esvaziar água” fica
intermitente para avisar que o recipiente está cheio.
! O indicador luminoso
“Esvaziar água” mantém-
se aceso para lembrar que
deve esvaziar o recipiente
de recolha da água no início
de cada programa.
Carregamento do sistema de recolha da água
Quando a máquina de secar roupa é nova, o
recipiente de recolha da água não efectua a
recolha enquanto o sistema não estiver carregado.
Esta operação pode precisar de 1 ou 2 ciclos de
secagem. Uma vez efectuado o carregamento, o
sistema recolhe a água em todos os ciclos.
2
Informações importantes
Para um funcionamento eficiente da máquina
de secar roupa por condensação, é necessário
respeitar o esquema de manutenção regular
indicado abaixo:
Filtro de cotão – É NECESSÁRIO limpar o cotão
que se deposita no filtro no fim de cada ciclo de
secagem.
Fase 1
Abra a porta da máquina de
secar roupa.
Fase 2
Extraia o filtro (com dois dedos).
Fase 3
Abra o filtro desbloqueando a
mola.
Fase 4
Limpe eventuais depósitos de
cotão da superfície interna da
rede do filtro.
Fase 5
Reinstale o filtro – Não ligue
nunca a máquina de secar roupa
sem ter colocado o filtro.
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
/