Stránka sa načítava...
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
BRIGGSandSTRATTON.COM
Manual No. 80022467 Rev B
Copyright © 2018. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON is a registered trademark of Briggs & Stratton Corporation.
GE2200BI
(030706-00)
en - English
da - Dansk
es - Español
fi - Suomi
fr - Français
hu - Magyar
nl - Nederlands
no - Norsk
pl - Polski
sv - Svenska
2 BRIGGSandSTRATTON.COM
E
D
R
K
V
F
U
T
M
H
G
B
A
C
S
1
J
L
PN
3
2
10
B
A
8
3
A
6
5
4
11
7
C
B
D
A
9
13
12
4 BRIGGSandSTRATTON.COM
Safety and Control Symbols ................... 4
Equipment Description........................ 4
Features and Controls ........................ 5
Operation................................... 5
Maintenance ................................ 8
Storage .................................... 9
Troubleshooting ............................10
Specifications ..............................10
Warranty ..................................11
The safety alert symbol indicates a potential personal
injury hazard. A safety symbol may be used to represent
the type of hazard. WARNING indicates a hazard which,
if not avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided, could
result in minor or moderate injury. NOTICE indicates
information considered important, but not hazard-related.
For questions regarding European emissions, please
contact our European office at:
The inverter generator is an engine–driven, revolving
field, alternating and direct current (AC & DC) generator.
The generator is designed to supply electrical power
for operating compatible electrical lighting, appliances,
tools and motor loads. The generator’s revolving field is
Lift generator using handle as handholds.
Every effort has been made to ensure that information
in this manual is accurate and current. However, the
manufacturer reserves the right to change, alter, or
otherwise improve the generator and this document at any
time without prior notice.
NOTICE If you have questions about intended use,
contact an authorized service dealer. This equipment is
designed to be used with Briggs & Stratton authorized
parts ONLY.
The generator has a system ground that connects the
generator frame components to the ground terminals
on the AC output receptacles. The generator neutral
is floating, which means that the AC stator winding
is isolated from the grounding fastener and the AC
receptacle ground pins. Electrical devices, such as RCD,
requiring a grounded neutral may not operate properly
from this generator.
There may be regulations, local codes, or ordinances
that apply to the intended use of the generator. Please
consult a qualified electrician, electrical inspector, or the
local agency having jurisdiction.
This generator is not intended to be used at a
construction site or similar activity.
EU Disposal
This symbol indicates the owner of
batteries and electrical or electronic
equipment shall not dispose of this
product with unsorted municipal waste.
This product should be disposed of in
environmentally appropriate waste
locations. Please contact Briggs & Stratton or your local
retailer for additional disposal information.
Fire
Explosion
Toxic Fumes
Hot Surface
Electrical Shock
Safety Alert
Symbol
Instruction Manual
Oil Level
Carbon
Monoxide Alarm
Circuit Breaker
On
Ground Terminal
Floating
Neutral
Off
Fuel
Engine Control
!
Do Not Start
Engine
Choke
Run
Suffication
Suffication
Oil
Alternating
Current (AC)
Direct
Current (DC)
5
Figure
1
Before starting the inverter generator there are two
equally important safety concerns regarding carbon
monoxide poisoning and fire that must be addressed.
THE RISK OF CARBON MONOXIDE POISONING
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas.
• Operate this product only outdoors far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• Do not run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for
hours, even after this product has shut off.
• Always place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air right away. See a doctor. You
may have carbon monoxide poisoning.
REDUCE THE RISK OF FIRE
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious injury.
• Portable generator must be at least 1.5 m (5 ft.) from
any structure, overhang, trees, windows, doors, any
wall opening, shrubs, or vegetation over 30.5 cm (12
in.) in height.
• Do not place portable generator under a deck or
other type of structure that may confine airflow.
Smoke alarm(s) must be installed and maintained
indoors according to the manufacturer’s instructions/
recommendations.
• Carbon monoxide alarms cannot detect smoke.
• Do not place portable generator in manner other than
shown.
1.5 m
(5 ft.) min.
1.5 m (5 ft.) min.
MUFFLER
Install carbon monoxide alarms inside
your home. Without working carbon
monoxide alarms, you will not realize
you are getting sick and dying from
carbon monoxide poisoning.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER
MUFFLER
from home
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
CARBON MONOXIDE
ALARM(S)
Install carbon monoxide alarms
inside your home. Without working
carbon monoxide alarms, you will not
realize you are getting sick and dying
from carbon monoxide poisoning.
A Choke Lever L Parallel Operation Port
B Side Maintenance Cover M Generator Reset
C Air Cleaner (under cover) N
QPT Switch
D Recoil Handle P LED Panel
E Oil Fill (under cover) R 230 Volt AC Receptacle
F Engine Switch S Top Maintenance Cover
G 12 Volt DC Receptacle T Spark Arrester Muffler
H DC Circuit Breaker U Identification Label
J Grounding Fastener V Fuel Cap
K Circuit Breaker
6 BRIGGSandSTRATTON.COM
Figure
2
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF
or higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity
for the engine. Use the chart to select the best viscosity
for the outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
3
4
5
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure generator is on a level surface.
2. Loosen two side maintenance cover screws and
remove cover.
3. Clean area around oil fill and remove oil fill cap.
4. Verify oil is at the point of overflowing at oil fill opening.
5. If needed, using oil funnel, slowly pour oil into oil fill
opening to the point of overflowing at oil fill.
6. Replace and tighten oil fill cap.
7. Replace maintenance cover and hand tighten screws.
NOTICE Do not attempt to crank or start engine before
before it has been properly serviced with recommended
oil. This could result in an engine failure.
Add Fuel Figure
1
6
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline with a minimum of
91 RON (87 octane/87 AKI).
• Gasoline with up to 10% ethanol content is acceptable.
NOTICE Do not mix oil in gasoline or modify engine to
run on alternate fuels. Do not use unapproved gasoline
such as E15 and E85. Use of unapproved fuels could
damage generator and voids warranty.
See High Altitude for 1,524 m (5,000 ft.) and above.
WARNING! Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury.
• Do not refuel during operation.
• Turn engine off and let it cool at least 2 minutes before
removing fuel cap.
• Fill fuel tank outdoors. Do not spill fuel.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• Do not light a cigarette or smoke.
• Do not pour water on generator to put out fire.
• Only use a extinguisher rated for flammable liquids
and electrical systems such as a powder extinguisher.
Follow the instructions provided by fire extinguisher
manufacturer before use.
• This generator is not for use in explosive atmospheres.
1. Slowly remove fuel cap (1,V) to relieve pressure in tank.
2. Slowly add unleaded fuel to red fuel level indicator
(6,A) in fuel tank. Be careful not to fill above the
indicator. This allows adequate space for fuel
expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
At altitudes over 1524 m (5,000 ft.), a minimum 89
RON (85 octane/85 AKI) fuel is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions.
See an Authorized Briggs & Stratton dealer for high
altitude adjustment information. Operation of the engine
at altitudes below 762 m (2,500 ft.) with the high altitude
kit is not recommended.
When transporting equipment with a vehicle or trailer,
turn engine switch to OFF (0) position. Do not tip engine
or equipment at angle which causes fuel to spill.
1
Disconnect all electrical loads from the generator. Use
the following start instructions:
1. Make sure unit is outdoors on a level surface.
NOTICE Failure to operate the unit on a level surface
may cause the unit to shut down.
2. Move choke lever (A) to CHOKE ( ) position.
NOTICE For a warm engine, be sure choke lever is in
RUN ( ) position.
3. Set engine switch (F) to ON (I) position.
NOTICE To help start the engine for the very first time,
after running out of fuel, or after a long period of storage,
fill fuel tank as described in Add Fuel. It may require
several starting attempts to purge air in the fuel system.
4. Grasp recoil handle (D) and pull slowly until slight
resistance is felt. Then pull rapidly to start engine.
5. As engine warms up, slowly move choke lever to
RUN ( ) position
NOTICE This unit is equipped with a low oil indicator.
If the engine oil drops below a preset level, an oil switch
will stop the engine. See Low Oil Indicator.
This feature improves fuel economy. When QPT switch (N)
is turned ON, the engine speed will increase as electrical
loads are connected, and decreased as electrical loads are
removed.
With the switch off, the engine will run at a higher speed.
7
1
Generator may only be loaded up to rated power under
the rated conditions as shown on unit data tag. Reduce
load when using generator outside of rated conditions.
Use only high quality, well-insulated extension cables in
accordance with IEC 245-4 with the generator’s 230 Volt
AC outlets. Inspect extension cables before each use.
Check that all extension cables are suitably rated and
are not damaged. When using extension cords under 40°
C, the total length of cords for a cross section of 1.5 mm²
should not exceed 50 m or for a cross section of 2.5 mm²
should not exceed 80 m.
WARNING! Damaged or overloaded extension
cords could overheat, arc, and burn resulting in
death or serious injury.
• Electrical equipment, including cables and plug
connections, should not be defective.
Use receptacles (R) to operate 230 Volt AC, single-phase,
50 Hz electrical loads. The receptacle is protected against
overload by a push-to-reset circuit breaker (K).
Protection of electrical components depends on circuit
breakers specifically matched to the generator. Replace
circuit breaker with identical rating and performance
characteristics.
WARNING! Generator voltage could cause
electrical shock or burn resulting in death or
serious injury.
• Do not touch bare wires or receptacles.
• Do not use generator with electrical cords which are
worn, frayed, bare or otherwise damaged.
• Do not operate generator in the rain or wet weather.
• Do not handle generator or electrical cords while
standing in water, while barefoot, or while hands or feet
are wet.
• Do not allow unqualified persons or children to operate
or service generator.
• Keep children a safe distance from generator.
The maximum current available for the 12 Volt DC
receptacle (G) is 60 Watts (5 Amps). A DC circuit
breaker (H) protects this receptacle from overloads. If an
overload occurs, the circuit breaker will trip (push button
pops out). Wait a few minutes and push the button in to
reset the circuit breaker.
This receptacle along with the USB adapter allows you to
recharge any USB powered device with a USB charging
cable (not included).
NOTICE For charging ITE (Information Technology
Equipment) only.
NOTICE When using this receptacle, push the QPT
switch to the OFF (0) position.
LED Panel Figure
7
The green LED output indicator light comes on when
the generator is operating normally. It indicates that the
generator is producing power at the receptacles.
Overload Alarm
The red LED overload alarm light comes on and cuts
power to the receptacles if you overload the generator.
The green output indicator light will also go off. If the
generator was overloaded, you must turn off and unplug
all electrical loads, then push the generator reset button
to continue operating.
The low oil indicator system is designed to prevent
engine damage caused by not enough engine oil. If the
engine oil level drops below a preset level, the yellow
LED low oil indicator light comes on and an oil switch will
stop the engine. If the engine stops or the yellow LED
low oil indicator light comes on when you pull the recoil
handle, check the engine oil level.
Two Briggs & Stratton inverter generators can be run
in parallel with a Briggs & Stratton parallel operation kit
(optional equipment). When running in parallel, the total
output of power is shown in chart.
Models
P2200 & P2200 3000 Watts
P2200 & P3000 3000 Watts
P3000 & P3000 4800 Watts
NOTICE Total electrical load connected to the parallel
kit must not exceed the maximum output.
See the parallel operation kits instruction sheet for
detailed instructions on installation and operation of the
connected generators.
1. Turn off and unplug all electrical loads from generator
panel receptacles. Never stop engine with electrical
devices plugged in and turned on.
2. Let engine run at no-load for one minute to stabilize
internal temperatures of engine and generator.
3. Push engine switch to OFF (0) position.
8 BRIGGSandSTRATTON.COM
Follow hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions.
1
Service more often under dirty or dusty conditions.
Regular maintenance will improve performance and
extend the life of the outdoor generator. See any Briggs
& Stratton Authorized Service Dealer for service.
Installation and major repair work should only be
performed by specifically trained personnel.
The generator’s warranty does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, the operator must
maintain the generator as instructed in this manual.
WARNING To ensure machine safety, use only
original spare parts from the manufacturer or
approved by the manufacturer. Should you have
questions about replacing components on your
generator, please visit our website at
BRIGGSandSTRATTON.COM.
CAUTION Excessive high or low operating
speeds could result in minor injury. Do not tamper
with governor spring, links or other parts to change
speed. Do not modify generator in any way.
8
The fuel strainer helps prevent debris from entering the
fuel system.
1. Make sure generator is on a level surface.
2. Remove the fuel cap (A) and fuel strainer (B).
3. Wash fuel strainer in liquid detergent and water.
4. Wipe fuel strainer clean with a clean, dry cloth.
5. Carefully reinstall the fuel strainer and fuel cap.
Changing Engine Oil Figure
3
4
5
CAUTION Avoid prolonged or repeated skin
contact with used motor oil. Used motor oil has
been shown to cause skin cancer in certain
laboratory animals. Thoroughly wash exposed areas with
soap and water.
KEEP OUT OF REACH OF CHILDREN. DON’T
POLLUTE. CONSERVE RESOURCES.
RETURN USED OIL TO COLLECTION
CENTERS.
Change oil while engine is warm from running, as follows:
1. Make sure generator is on a level surface.
2. Loosen side maintenance cover screws and remove
cover.
3. Clean area around oil fill and remove oil fill cap.
4. Tip your generator to drain oil from oil fill into a
suitable container making sure you tip your unit
toward the oil filler neck. When crankcase is empty,
return generator to upright position.
5. Using oil funnel, slowly pour oil (about 0.4 l (13.5
oz.)) into oil fill opening to the point of overflowing at
oil fill cap. DO NOT overfill.
6. Reinstall oil fill cap. Finger tighten cap securely.
7. Wipe up any spilled oil.
8. Reinstall side maintenance cover and hand tighten
screws.
Service Air Cleaner Figure
3
9
Your engine will not run properly and may be damaged if
you run it with a dirty air cleaner.
1. Loosen side maintenance cover screws and remove
cover.
2. Loosen air cleaner cover screw (A) and remove air
cleaner cover (B).
3. Carefully remove foam air cleaner (C) and breather
filter (D) by pulling it out towards you.
4. Wash foam air cleaner and breather filter in liquid
detergent and water only. Squeeze dry in a clean cloth.
5. SATURATE foam air cleaner in clean engine oil and
squeeze in a clean cloth to remove excess oil.
6. Reinstall clean or new foam air cleaner and breather
filter inside base.
7. Reinstall the air cleaner cover and tighten screw.
8. Reinstall the side maintenance cover and hand
tighten screws.
Every 8 Hours or Daily
• Clean debris
• Check engine oil level
• Change engine oil
Every 50 Hours
• Service engine air cleaner and breather filter
1
• Change engine oil
1
Every 100 Hours
• Clean fuel strainer
• Service spark plug
• Inspect spark arrester
• Check valve clearance
9
Service Spark Plug Figure
1
10
11
Changing the spark plug will help your engine to start
easier and run better.
1. Remove top maintenance cover (1,S).
2. Clean area around spark plug and remove spark
plug boot.
3. Remove spark plug and inspect spark plug.
4. Replace spark plug if electrodes are pitted, burned
or porcelain is cracked. Use the recommended
replacement plug. See Specifications.
5. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specifications).
6. Install spark plug and tighten firmly. Reinstall spark
plug boot.
7. Reinstall top maintenance cover.
12
13
The engine exhaust muffler has a spark arrester screen.
Inspect the muffler for cracks, corrosion, or other
damage. Inspect spark arrester screen for damage or
carbon blockage. Clean if carbon blockage is found using
brush and commercial solvent or replace if damaged.
WARNING! Contact with muffler area could
cause burns resulting in serious injury.
• Pay attention to the warnings on the generator.
• Do not touch hot parts.
1. To remove muffler guard, remove four screws that
connects guard to generator.
2. Remove screw that attaches spark arrester screen
to muffler. Remove spark arrester screen.
3. Inspect screen and obtain a replacement if torn,
perforated or otherwise damaged. DO NOT use a
defective screen. If screen is not damaged, clean it
with a brush.
4. Reattach screen to muffler. Reattach muffler guard.
Check Valve Clearance
Regular valve clearance check and adjustment will
improve performance and extend engine life. This
procedure cannot be done without partial engine
disassembly and the use of special tools. For this
reason we recommend that you have a Briggs & Stratton
Authorized Service Dealer check and adjust valve
clearance at recommended intervals (see Maintenance
Schedule).
If storing the unit for more than 30 days, use the following
guidelines to prepare it for storage.
Change Engine Oil
While engine is still warm, drain oil from crankcase. Refill
with recommended grade. See Changing Engine Oil.
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine outdoors for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine outdoors until it stops from lack of fuel.
The use of a fuel stabilizer in the storage container is
recommended to maintain freshness.
WARNING! Fuel and its vapors are
extremely flammable and explosive
which could cause burns, fire or
explosion resulting in death or serious injury.
• When storing fuel or equipment with fuel in tank, store
away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
• When draining fuel, turn generator engine off and let it
cool at least 2 minutes before removing fuel cap.
• Loosen cap slowly to relieve pressure in tank.
• Drain fuel tank outdoors.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
Store generator in clean, dry area and cover with a
suitable protective cover that does not retain moisture.
WARNING! Storage covers could cause a fire
resulting in death or serious injury.
• Do not place a storage cover over a hot generator.
• Let equipment cool for a sufficient time before placing
the cover on the equipment.
10 BRIGGSandSTRATTON.COM
Problem Cause
1. Red overload alarm light is on.
Generator is overloaded.
2. Green output indicator light not on.
Fault in generator.
3. Poor connection or defective cord set.
4. Connected device is bad.
1. Remove loads from generator.
Press RESET button on control
panel.
2. Contact authorized dealer.
3. Check and repair.
4. Connect another device that is in
good condition.
1. Generator is overloaded.
1. Remove loads from generator.
down when running.
1. Engine switch set to OFF (0) position.
2. Low oil level.
3. Dirty air cleaner.
4. Out of fuel.
5. Spark plug wire not connected to
spark plug.
6. Flooded with fuel.
1. Set switch to ON (I) position.
2. Fill crankcase to proper level or
place generator on level surface.
3. Clean or replace air cleaner.
4. Fill fuel tank.
5. Connect wire to spark plug.
6. Wait 5 minutes and re-crank engine.
* This generator is rated in accordance with Briggs & Stratton 628K. Starting Watts represents the momentary electrical current the
generator can provide to start electric motors. Starting Watts does not represent the power required to continuously run electrical
loads. Starting Watts is the maximum current that can momentarily be supplied when starting a motor, multiplied by the generator’s
rated voltage.
** Generator per EN ISO 8528-13:2016, Reciprocating internal combustion engine driven generating sets-Part 13: Safety.
Starting Watts* .................................................. 2,200
Running Watts** ................................................. 1,700
AC Current at 230 Volts AC ....................................7.4 Amps
AC Current at 12 Volts DC .....................................5.0 Amps
Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Hz at 4500 rpm
Phase ...................................................Single Phase
Displacement ....................................... 111 cc (6.77 cu. in.)
Spark Plug Gap ..............................0.6-0.7 mm (0.023-0.027 in.)
Fuel Capacity .................................3.7 Liters (1.0 U.S. Gallons)
Oil Capacity .....................................0.4 Liters (13.5 Ounces)
Foam Air Cleaner ............................................311388GS
Breather Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .311389GS
Resistor Spark Plug ...................................... NGK CR7HSA
Engine Oil Bottle ....................................100005E or 100007E
Synthetic Oil Bottle ............................................100007W
Fuel Stabilizer ........................................ 992380 or 992381
Spark Arrester...............................................315584GS
For a full list of parts and diagrams, please visit BRIGGSandSTRATTON.COM.
11
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for
and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for
inspection and testing.
.
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state or country to country.**
After 12 months, warranty covers parts only.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a retail
consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial
use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for
warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or abuse,
improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s
Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the
product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage or water/chemical
corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or
repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal
use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine brake pads) are
not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in
place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or
engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
24 months 12 months
80011061_EN Rev A
4 BRIGGSandSTRATTON.COM
........... 4
.................. 4
...................... 5
.............................. 5
..................... 8
................................9
.............10
.............................10
.................................11
би могла
БЕЛЕЖКА
switch off
БЕЛЕЖКА
Stratton.
!
(DC)
5
1
Install carbon monoxide alarms inside
your home. Without working carbon
monoxide alarms, you will not realize
you are getting sick and dying from
carbon monoxide poisoning.
CARBON MONOXIDE ALARM(S)
USE OUTDOORS - AVOID CARBON MONOXIDE POISONING
point away
from home
MUFFLER
A L
B
M
C
N
D P
E
R
F
S
G
T
H U
J
V
K
6 BRIGGSandSTRATTON.COM
2
3
4
5
БЕЛЕЖКА
1
6
БЕЛЕЖКА
Голяма надморска височина
1,V
6,A
1
БЕЛЕЖКА
A
CHOKE ( ).
БЕЛЕЖКА
).
F
БЕЛЕЖКА
Наливане на гориво.
D
)
7
БЕЛЕЖКА
Индикатор за ниско ниво на маслото.
N
1
R
K).
DC (GH
БЕЛЕЖКА
БЕЛЕЖКА
7
3000 W
3000 W
4800 W
БЕЛЕЖКА
8 BRIGGSandSTRATTON.COM
1
BRIGGSandSTRATTON.COM.
8
(AB).
3
4
5
3
9
(AB).
CD
1
1
9
1
10
11
Спецификации.
Спецификации).
12
13
График за техническото обслужване).
Смяна на маслото на двигателя.
10 BRIGGSandSTRATTON.COM
.
........................................2200
...............................................1700
.................................................. 7.4 A
.....................................................5 A
.............................................50 Hz
.................................................
..........................
..
.......
...............
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .311388GS
.......................................311389GS
........................... NGK CR7HSA
.........................
....................................100007W
.............................
..............................................315584GS
11
.
**
**
80011061_BG Rev A
4 BRIGGSandSTRATTON.COM
Obsah
............... 4
............................... 4
............................ 5
Provoz ..................................... 5
..................................... 8
.................................. 9
............................10
Specifikace ................................10
....................................11
VAROVÁNÍ ukazuje na riziko,
může
POZOR ukazuje na riziko,
může
UPOZORNENI
) a
tuto dokumentaci.
UPOZORNENI
DÍLY Briggs & Stratton.
Likvidace v EU
povrch
kapaliny
Hladina
oleje
Detektor oxidu
svorka
Palivo
motoru
!
Nestartujte
motor
Olej
(
Zapnuto Vypnuto
Provoz
proud (AC)
proud (ss)
/