Whirlpool AVTL 104 (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
1
GB
Contents
Installation, 2-3
Unpacking and levelling, 2
Electric and water connections, 2-3
The first wash cycle, 3
Technical details, 3
Washing machine description, 4-5
Control panel, 4
How to open and shut the drum, 5
Leds, 5
Starting and Programmes, 6
Briefly: how to start a programme, 6
Programme table, 6
Personalisations, 7
Setting the temperature, 7
Setting the spin cycle, 7
Functions, 7
Detergents and laundry, 8
Detergent dispenser, 8
Bleach cycle, 8
Preparing your laundry, 8
Special items, 8
Woolmark Platinum Care, 8
Precautions and advice, 9
General safety, 9
Disposal, 9
Saving energy and respecting the environment, 9
Care and maintenance, 10
Cutting off the water or electricity supply, 10
Cleaning your appliance, 10
Caring for your appliance door and drum, 10
Cleaning the pump, 10
Checking the water inlet hose, 10
Cleaning the detergent dispenser, 10
Troubleshooting, 11
Service, 12
Before calling for Assistance, 12
WASHING MACHINE
AVTL 104
Instructions for use
Magyar, 61
HU
English, 1
GB
Polski, 13
CIS
ÐÓÑÑÊÈÉ, 25
CZ
Èeský, 49
SK
Slovenský, 37
ES
PL
2
GB
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing
machine.
2. Check whether the
washing machine has
been damaged during
transport. If this is the
case, do not install it
and contact your
retailer.
3. Remove the four
protective screws and
the rubber washer with
the respective spacer,
situated on the rear of
the appliance (see
figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if the
washing machine needs to be moved to another
location.
Warning: should the screws be re-used, make sure
you fasten the shorter ones at the top.
Packaging materials are not children's toys.
Levelling
1. Install the washing machine on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or
loosening the adjustable
front feet (see figure); the
angle of inclination,
measured according to
the worktop, must not
exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded mouth (see
figure).
Before making the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the other end
of the water inlet hose to
the washing machine,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the rear
of the appliance
(see figure).
3. Make sure there are no kinks or bends in the
hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Installation
A
3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
alternatively, place it
over the edge of a
basin, sink or tub,
fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine's plug. If this is not the case, replace the
socket or the plug.
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
When the washing machine is installed, the main
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, setting the 90°C
programme without a pre-wash cycle.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Technical details
Model
AVTL 104
Dimensions
40 cm wide
85 cm high
60 cm deep
Capacity
from 1 to 5 kg
Electric
connections
voltage 220/230 Volts 50 Hz
maximum absorbed power 1850 W
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 42 litres
Spin speed
up to 1000 rpm
Control
programmes
according to
IEC456 directive
programme 3; temperature 60°C;
run with a load of 5 kg.
This appliance is compliant with the
following European Community
Directives:
- 73/23/CEE of 19/02/73 (Low
Voltage) and subsequent amendments
- 89/336/CEE of 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments
- 2002/96/CE
65 - 100 cm
4
GB
Control panel
Washing machine description
ON-OFF/LID LOCK led:
If this LED is on, the appliance Lid is locked to prevent it from being opened accidentally; to avoid any damages,
you must wait for the lamp to flash before you open the Lid.
.
The rapid flashing of the ON-OFF/LID LOCK Led together with the flashing of at least one other LED indicates
there is an abnormality (see page 11).
TEMPERATURE
knob
PROGRAMME
knob
LEDs
FUNCTION
keys
ON/OFF
key
START/RESET
key
SPIN SPEED
knob
LID LOCKED
LED
Detergent dispenser to add detergent and fabric
softener (see page 8).
LEDs to find out which wash cycle phase is under way.
If the Delay Timer function has been set, the time left
until the programme starts will be indicated (see page
5).
SPIN SPEED knob to set the spin speed or exclude
the spin cycle completely (see page 7).
FUNCTION keys to select the functions available. The
button corresponding to the function selected will
remain on.
TEMPERATURE knob to set the temperature or the
cold wash cycle (see page 7).
ON/OFF key to turn the washing machine on and
off.
START/RESET key to start the programmes or
cancel incorrect settings.
ON-OFF/LID LOCK led ,to find out whether the
washing machine is on (flashing) and if the lid may be
opened (see page 5).
PROGRAMME knob to set the programmes
(see page 6).
The knob stays still during the cycle.
5
GB
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Leds
The LEDS provide important information.
This is what they can tell you:
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate
on to indicate the cycle phase under way:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the LED corresponding to the
Spin cycle phase will be turned on.
Function keys
The FUNCTION KEYS also act like LEDS.
When a function is selected, the corresponding button
is illuminated.
If the function selected is incompatible with the
programme set, the button will flash and the function
will not be enabled.
If you set a function that is incompatible with another
function you selected previously, only the last one
selected will be enabled.
Fig. 3
Fig. 4
Fig. 1
Fig. 2
A) Opening (Fig. 1).
Lift the external lid and open it completely.
B) Then open the drum using both hands as
shown in Fig. 2:
- press the button indicated by the arrow in Fig. 2
lightly downwards, with one hand firmly resting on
the doors to prevent them from suddenly opening
and hurting your fingers;
- therefore follow the appliance doors along as these
unhook and open easily.
C) Loading the washing machine. (Fig. 3).
D) Shutting (Fig. 4).
- close the drum fully by first shutting the front door
followed by the rear one;
- then ensure the hooks on the front door are perfectly
housed within the seat of the rear door;
- after the hooks have clicked into position, press both
doors lightly downwards to make sure they do not
come loose;
- finally shut the external lid.
How to open and to close the drum
6
GB
Starting and Programmes
Notes
For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative.
Special programme
Daily 30' (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only
lasts 30 minutes and allows you to save on both time and energy. By setting this programme (9 at 30°C), you can
wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Briefly: starting a programme
1. Switch the washing machine on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine, add
the detergent and any fabric softener (see page 8)
and shut the appliance door.
3. Set the PROGRAMME knob to the programme
required.
4. Set the wash temperature (see page 7).
5. Set the spin speed (see page 7).
6. Start he programme by pressing the START/RESET
button.
To cancel it, keep the START/RESET button pressed
for at least 2 seconds.
7. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button
.
Type of fabric and degree
of soil
Program-
mes
Wash
temper-
at.
Detergent
Fabric
softener
Bleaching
/option
Bleach
Cycle
length
(minutes)
Description of wash cycle
Pre-
wash
Wash
Cotton
Extremely soiled whites
(sheets, tablecloths, etc.)
1
90°C 1
5
2
Pre-wash, wash cycle, rinse
cycles, intermediate and final
spin cycles
Extremely soiled whites
(sheets, tablecloths, etc.)
2
90°C
Delicate/
Traditional
1
4
4
Wash cycle, rinse cycles,
intermediate and final spin
cycles
Heavily soiled whites and
fast colours
3
60°C
Delicate/
Traditional
1
5
9
Wash cycle, rinse cycles,
intermediate and final spin
cycles
Heavily soiled whites and
fast colours
4
40°C
Delicate/
Traditional
9
3
Wash cycle, rinse cycles,
intermediate and final spin
cycles
Slightly soiled whites and
delicate colours (shirts,
jumpers, etc.)
5
30°C
Delicate/
Traditional
8
5
Wash cycle, rinse cycles,
intermediate and final spin
cycles
Synthetics
Heavily soiled fast colours
(baby linen, etc.)
6
60°C
Delicate
9
4
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Heavily soiled fast colours
(baby linen, etc.)
7
50°C
Delicate
9
0
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Delicate colours (all types
of slightly soiled
garments)
8
40°C
Delicate
8
0
Wash cycle, rinse cycles, anti-
crease or delicate spin cycle
Delicate colours (all types
of slightly soiled
garments)
9
30°C 32
Wash cycle, rinse cycles and
delicate spin cycl
Delicate
Wool
10
40°C
Delicate
60
Wash cycle, rinse cycles and
delicate spin cycle
Very delicate fabrics
(curtains, silk, viscose,
etc.)
11
30°C
6
7
Wash cycle, rinse cycles, anti-
crease or draining cycle
PARTIAL PROGRAMMES
Rinse Rinse cycles and spin cycle
Delicate rinse cycle
Rinse cycles, anti-crease or
draining
Spin cycle
Draining and heavy duty spin
cycle
Delicate spin cycle
Draining and delicate spin
cycle
Draining Draining
Programme table
7
GB
Function Effect Comments Enabled with
programmes:
Super
Wash
Allows for an
impeccable
wash, visibly
whiter than a
standard
Class A wash.
This function is incompatible with the RAPID function. 1, 2, 3, 4,
5, 6, 7, 8
Easy iron This option
reduces the
amount of
creasing on
fabrics,
making them
easier to iron.
When this function is set, programmes 6, 7, 8, 11 and
Delicate rinse will end with the laundry left to soak
(Anti-crease) and the Rinse cycle phase LED will
flash.
- to conclude the cycle, press the START/RESET
button;
- to run the draining cycle alone, set the knob to the
relative symbol and press the START/RESET
button.
All
programmes
except for
1, 2, 9, 10
and
Draining.
Rapi d Cuts the
duration of
the wash
cycle by 30%.
This function is incompatible with the SUPER WASH
function.
1, 2, 3, 4,
5, 6, 7, 8
Rinses
Ext ra
Rinse
Increases the
efficiency of
the rinse.
Recommended when the appliance has a full load or
with large quantities of detergent.
1, 2, 3, 4, 5,
6, 7, 8, and
Rinse
cycles.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
Personalisations
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash (
).
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the programme selected.
The maximum spin speeds for each programme are as follows:
Programmes Maximum spin speed
Cottone 1000 rpm
Synthetics 800 rpm
Wool 600 rpm
Silk no
The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol
.
The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed for
each programme.
To avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by
continuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than
the set frequency.
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the
programme set.
8
GB
Detergent dispenser
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up
on the interior of your
appliance and even
pollute the
environment.
Open up the
detergent dispenser
and pour in the
detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
compartment 2: Detergent for the wash cycle
(powder or liquid)
It is recommended that you place liquid detergent
directly into the compartment using the appropriate
dosing cup.
compartment 3: Additives (softener, etc.)
When pouring the softener in compartment 3, avoid
exceeding the "max" level indicated.
The softener is added automatically into the machine
during the last wash. At the end of the wash
programme, some water will be left in compartment
3. This is used for the inlet of denser fabric softeners
into the machine, i.e. to dilute the more
concentrated softeners. Should more than a normal
amount of water remain in compartment 3, this
means the emptying device is blocked. For cleaning
instructions, see page 10.
compartment 4: Bleach
Do not use hand wash detergent because it may
form too much foam.
Bleach cycle
Traditional bleach should be used on sturdy white
fabrics, and delicate bleach for coloured fabrics,
synthetics and for wool.
When pouring in the bleach, be careful not to exceed
the "max" level indicated on compartment 4 ..
To run the bleach cycle alone, pour the bleach into
compartment 4 and set the Rinse programme
(for
cotton fabrics) or delicate Rinse
(for synthetic
fabrics).
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from
whites.
Empty all pockets and check for loose buttons.
Do not exceed the weight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow
case or mesh bag. Wash them separately without
exceeding half the appliance load. Use programme
11 which excludes the spin cycle automatically.
Quilted coats and windbreakers: if they are
padded with goose or duck down, they can be
machine-washed. Turn the garments inside out and
load a maximum of 2-3 kg, repeating the rinse cycle
once or twice and using the delicate spin cycle.
Trainers: remove any mud. They can be washed
together with jeans and other tough garments, but
not with whites.
Wool: for best results, use a specific detergent,
taking care not to exceed a load of 1 kg.
Woolmark Platinum Care
As gentle as a hand wash.
Ariston sets a new standard of superior
performance that has been endorsed by
The Woolmark Company with the
prestigious Woolmark Platinum Care brand. Look for
the Woolmark Platinum Care logo on the washing
machine to ensure you can safely and effectively
wash wool garments labelled as "hand wash"
(M.0303):
Set programme 10 for all "Hand wash"
garments,
using the appropriate detergent (max load 1 Kg).
Detergents and laundry
9
GB
Precautions and advice
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
The washing machine was designed and built in
compliance with the applicable international safety
regulations. The following information is provided for
your safety and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not open the detergent dispenser while the
appliance is in operation.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
The appliance door tends to get quite hot during
the wash cycle.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
Disposing of the packaging material: observe local
regulations, so the packaging can be re-used.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of
the materials they contain and reduce the impact on
human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Disposing of an old washing machine:
before scrapping your appliance, cut the power
supply cable and remove the appliance door.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance
door, this is because thanks to the latest technology,
your washing machine only needs less than half the
amount of water to get the best results: an objective
reached to respect the environment.
Saving on detergent, water,
energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity
supply
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
Unplug your appliance when cleaning it and
during all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out
(see figure).
Wash it under running water; this operation should
be repeated
frequently.
Caring for your appliance door and
drum
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
To recover any objects that have fallen into the pre-
chamber:
1. remove the plinth at
the bottom on the
front side of the
washing machine by
pulling from the side
with your hands (see
diagram); (see figure);
2. unscrew the lid
rotating it anticlock-
wise (see figure): a
little water may trickle
out. This is perfectly
normal;
3. clean the interior
thoroughly;
4. screw the lid back
on;
5. reposition the panel,
making sure the hooks
are securely in place
before you push it onto
the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during
the wash cycles, water pressure is very strong and
a cracked hose could easily split open.
Never use hoses that have already been used.
Make sure the wash cycle has ended and unplug
the appliance.
How to clean the detergent dispenser
Fig. 1 Fig. 2
Cleaning:
Then clean the dispenser under a tap (fig. 3) using an old
toothbrush and, once the pair of siphons inserted in the
top of compartments 1 and 2 (fig. 4) have been pulled
out, check whether the same are not clogged and then
rinse them.
Reassembly:
Do not forget to reinsert the
pair of siphons into the
special housings and then to
replace the dispenser into its
seat, clicking it into place
(fig. 4, 2 and 1).
Disassembly:
Press lightly on the large
button on the front of the
detergent dispenser and pull
it upwards (fig. 1).
Fig. 3
Fig. 4
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem
can't easily be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won't
start.
The wash cycle won't start.
The washing machine fails to
load water.
The washing machine
continuously loads and unloads
water.
The washing machine does not
drain or spin.
The washing machine vibrates
too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same
time as at least one other LED.
There is too much foam.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance Lid is not shut properly. The Lid locked Led flashes.
The
button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn't have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and call for Assistance. If the dwelling is on one of the upper
floors of a building, there may be drain trap problems causing the washing
machine to load and unload water continuously. In order to avoid such an
inconvenience, special anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Easy iron option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The washing machine is not level (see page 2).
The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not suitable for machine washing (it should bear
the definition "for washing machines" or "hand and machine wash",
or the like).
You used too much detergent.
ServiceTroubleshootingPrecautions CareProgrammes DetergentsInstallation Description
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N);
This information can be found on the data plate situated on the rear of the washing machine.
Service
Service
13
PL
Polski
Spis treci
Instalacja, 14-15
Rozpakowanie i wypoziomowanie, 14
Pod³¹czenie do sieci wodnej i elektrycznej, 14-15
Pierwszy cykl prania, 15
Dane techniczne, 15
Opis pralki, 16-17
Panel kontrolny, 16
Jak otwieraæ i zamykac kosz, 17
wiate³ka sygnalizuj¹ce, 17
Uruchomienie i Programy, 18
Krótko mówi¹c: jak nastawiæ program, 18
Tabela programów, 18
Potrzeby indywidualne, 19
Nastawienie temperatury, 19
Nastawienie wirowania, 19
Funkcje, 19
rodki pior¹ce i bielizna, 20
Szufladka na rodki pior¹ce, 20
Cykl wybielania, 20
Przygotowanie bielizny, 20
Tkaniny wymagaj¹ce szczególnej dba³oci, 20
Woolmark Platinum Care, 20
Zalecenia i rodki ostro¿noci, 21
Ogólne zasady bezpieczeñstwa, 21
Usuwanie odpadów, 21
Oszczêdnoæ i ochrona rodowiska, 21
Konserwacja, 22
Wy³¹czenie wody i pr¹du elektrycznego, 22
Czyszczenie pralki, 22
Czyszczenie szufladki na rodki pior¹ce, 22
Czyszczenie drzwiczek i bêbna, 22
Czyszczenie pompy, 22
Kontrola rury doprowadzania wody, 22
Jak czyciæ szufladkê rodków pior¹cych, 22
Anomalie i rodki zaradcze, 23
Serwis Techniczny, 24
Przed zwróceniem siê do Serwisu Technicznego, 24
PRALKA
AVTL 104
Instrukcja obs³ugi
PL
14
PL
Nale¿y zachowaæ niniejsz¹ ksi¹¿eczkê instrukcji dla
przysz³ych konsultacji. W razie sprzeda¿y, oddania,
czy przeniesienia pralki w inne miejsce nale¿y
upewniæ siê, by przekazana zosta³a ona razem z
instrukcj¹, aby nowy w³aciciel zapoznaæ siê móg³ z
dzia³aniem urz¹dzenia i odpowiednimi informacjami.
Nale¿y uwa¿nie przeczytaæ instrukcjê obs³ugi, gdy¿
zawiera ona wa¿ne informacje dotycz¹ce instalacji
oraz w³aciwego i bezpiecznego u¿ytkowania pralki.
Rozpakowanie i wypoziomowanie
Rozpakowanie
1. Rozpakowaæ pralkê.
2. Sprawdziæ, czy nie
dozna³a ona uszkodzeñ
w czasie transportu.
Jeli by³aby ona
uszkodzona, nie
pod³¹czaæ jej i
powiadomiæ
sprzedawcê.
3. Odkrêciæ cztery ruby
ochronne, zamocowane
na czas transportu, oraz
zdj¹æ gumow¹ podk³adkê
z odpowiedni¹ rozpórk¹,
znajduj¹ce siê w tylnej
cianie i (zobacz rysunek).
4. Zatkaæ otwory przy pomocy za³¹czonych do pralki
plastykowych zalepkek.
5. Zachowaæ wszystkie te czêci: gdyby okaza³o siê
konieczne przewiezienie pralki w inne miejsce,
powinny one zostaæ ponownie zamontowane.
Uwaga: w razie ponownego uzycia kròtsze srubki
powinny byc przymocowane u gòry.
Czêci opakowania nie nadaj¹ siê do zabawy dla
dzieci
Wypoziomowanie
1. Ustawiæ pralkê na
p³askiej i twardej
pod³odze; nie opieraæ
jej o ciany, meble itp.
2. Jeli pod³oga nie jest
dok³adnie pozioma,
nale¿y wypoziomowaæ
pralkê, dokrêcaj¹c lub
odkrêcaj¹c przednie
nó¿ki (zobacz rysunek)
.
K¹t nachylenia, zmierzony
na górnym blacie pralki, nie powinien przekraczaæ 2°.
Staranne wypoziomowanie pralki zapewnia jej
stabilnoæ i zapobiega wibrowaniu, ha³asom i
przesuwaniu siê urz¹dzenia w czasie pracy. W
razie ustawienia na dywanie lub wyk³adzinie
dywanowej nale¿y tak wyregulowaæ nó¿ki, aby pod
pralk¹ pozostawa³a wolna przestrzeñ niezbêdna dla
wentylacji.
Pod³¹czenie do sieci wodnej i elektrycznej
Pod³¹czenie rury pobierania wody
1. Wsun¹æ uszczelkê A
do koñcówki rury
pobierania wody i
przykrêciæ do kurka
zimnej wody o
gwintowanym otworze
3/4'' (zobacz rysunek).
Przed pod³¹czeniem
upuciæ wodê, a¿
bêdzie zupe³nie czysta
i przeroczysta.
2. Pod³¹czyæ rurê
pobierania wody do
pralki, przykrêcaj¹c
do odpowiedniego
otworu pobierania wody,
znajduj¹cego siê w
tylnej cianie pralki, z
prawej strony u góry
(zobacz rysunek).
3. Zwróciæ uwagê, by na rurze nie by³o zgiêæ ani
ciniêæ.
Cinienie hydrauliczne kurka powinno mieciæ siê
w przedziale podanym w tabeli Danych
technicznych (zobacz na s¹siedniej stronie).
Jeli rura doprowadzania wody okaza³aby siê za
krótka, nale¿y zwróciæ siê do wyspecjalizowanego
sklepu lub do upowa¿nionego fachowca.
Instalacja
A
15
PL
Pod³¹czenie rury usuwania wody
Pod³¹czyæ rurê
usuwania wody, bez
zginania jej, do
przewodu ciekowego
lub do cieku w cianie,
które powinny
znajdowaæ siê na
wysokoci od 65 do 100
cm od pod³ogi;
lub oprzeæ na brzegu
zlewu lub wanny,
przymocowuj¹c do
kranu za³¹czony do
pralki prowadnik
(zobacz rysunek).
Wolny koniec rury
usuwania wody nie
powinien pozostawaæ
zanurzony w wodzie.
Odradza siê u¿ywanie rur-przed³u¿aczy; jeli
przed³u¿acz jest jednak konieczny, powinien mieæ
on ten sam przekrój, co rura oryginalna, i nie
powinien przekraczaæ 150 cm d³ugoci.
Pod³¹czenia elektryczne
Przed wprowadzeniem wtyczki do gniazdka nale¿y
upewniæ siê, czy:
gniazdko ma odpowiednie uziemnienie i czy
odpowiada obowi¹zuj¹cym przepisom;
gniazdko jest w stanie wytrzymaæ obci¹¿enie
maksymalnej mocy urz¹dzenia, podanej w tabeli
Danych Technicznych (zobacz obok);
napiêcie pr¹du elektrycznego w sieci zgodne jest
z danymi podanymi w tabeli Danych Technicznych
(zobacz obok);
gniazdko odpowiada wtyczce pralki. W
przeciwnym razie nale¿y wymieniæ gniazdko lub
wtyczkê.
Nie nale¿y instalowaæ pralki na otwartym
powietrzu, nawet jeli miejsce to jest chronione
daszkiem, gdy¿ wystawienie urz¹dzenia na dzia³anie
deszczu i burz, jest bardzo niebezpieczne.
Po zainstalowaniu pralki gniazdko elektryczne
powinno byæ ³atwo dostêpne.
Nie u¿ywaæ przed³u¿aczy ani wtyczek
wielokrotnych.
Kabel nie powinien mieæ zgiêæ ani nie powinien byæ
zgnieciony.
Kabel zasilania elektrycznego mo¿e byæ wymieniony
wy³¹cznie przez upowa¿nionego technika specialistê.
Uwaga! Producent uchyla siê od wszelkiej
odpowiedzialnoci, jeli nie przestrzega siê powy¿szych
zasad.
Pierwszy cykl prania
Po zainstalowaniu, zanim zacznie siê u¿ywaæ pralki,
nale¿y wykonaæ jeden cykl prania ze rodkiem pior¹cym,
lecz bez bielizny, nastawiaj¹c program na 90°C bez
prania wstêpnego.
Serwis
techniczny
Nieprawid³owoci
w dzia³aniu
Zasady
ostro¿noci
KonserwacjaProgramy rodki pior¹ceInstalacja Opis
Dane techniczne
Model
AVTL 104
Wymiary
szerokoæ cm 40
wysokoæ cm 85
êbokoæ cm 60
Pojemnoæ
od 1 do 5 kg
Dane pr¹du
elektrycznego
Napiêcie 220/230 Volt 50 Hz
maksymalna moc pobierana 1850 W
Dane sieci
wodoci¹gowej
Maksymalne cinienie 1 MPa (10 barów)
cinienie minimalne 0,05 MPa (0,5 barów)
pojemnoæ bêbna 42 litrów
Szybkoæ wirowania
do 1000 obrotów na minutê
Programy kontrolne
zgodnie z przepisami
IEC456
program 3; temperatura 60
°
C;
wykonane przy 5 kg za³adowanej bielizny.
Urz¹dzenie to zosto wyprodukowane
zgodnie z nastêpuj¹cymi przepisami EWG:
- 73/23/CEE z dn. 19/02/73 (o Niskim
Napiêciu) wraz z kolejnymi zmianami
- 89/336/CEE z dn. 03/05/89
(o Kompatybilnoci Elektromagnetycznej)
wraz z kolejnymi zmianami
- 2002/96/CE
65 - 100 cm
16
PL
Opis pralki
wiate³ko sygnalizuj¹ce ZAPALENIE/ZABLOKOWANE DRZWICZKI:
To wiate³ko sygnalizacyjne zapalone wskazuje, ¿e drzwiczki pralki zablokowane, aby zapobiec
przypadkowemu ich otwarciu; aby unikn¹æ szkód nale¿y odczekaæ do momentu, w którym wiate³ko zacznie
pulsowaæ, po czym mo¿na otworzyæ drzwiczki.
! Szybkie pulsowanie wiate³ka ZAPALENIE/ZABLOKOWANE DRZWICZKI przy jednoczesnym pulsowaniu
przynajmniej jeszcze jednego innego wiate³ka sygnalizacyjnego wskazuje nieprawid³owe dzia³anie pralki (patrz str. 23).
Panel kontrolny
Pokrêt³o
TEMPERATURY
Pokrêt³o
PROGRAMÓW
wiate³ka
sygnalizuj¹ce
Przyciski
FUNKCYJNE
Przycisk
W£¥CZENIE/
WY£¥CZENIE
Przycisk
START/RESET
Pokrêt³o
WIROWANIA
wiate³ko sygnalizuj¹ce
POKRYWA
ZABLOKOWANA
Szufladka na rodki pior¹ce s³u¿y do wsypania
rodków pior¹cych i dodatków (zobacz str. 20).
mwiate³ka sygnalizuj¹ce umo¿liwiaj¹ ledzenie
stanu postêpowania programu prania.
Jeli nastawiona zosta³a funkcja Delay Timer,
wska¿¹ one czas pozostaj¹cy do uruchomienia siê
programu (zobacz str. 17).
Pokrêt³o WIROWANIE s³u¿y do nastawienia lub
wykluczenia wirowania (zobacz str. 19).
Przyciski FUNKCJA s³u¿¹ do wybrania
po¿¹danych funkcji. Przycisk odnosz¹cy siê do
wybranej funkcji zawieci siê po jej nastawieniu.
Pokrêt³o TEMPERATURA s³u¿y do ustawienia
temperatury prania lub nastawienia prania w zimnej
wodzie (zobacz str. 19).
Przycisk W£¥CZANIE/WY£¥CZANIE s³u¿y do
w³¹czania i wy³¹czania pralki.
Przycisk START/RESET s³u¿y do uruchamiania
programów lub do anulowania b³êdnie nastawionych.
wiate³ko sygnalizuj¹ce W£¥CZENIE/POKRYWA
ZABLOKOWANA s³u¿y do zrozumienia, czy pralka
jest w³¹czona (lampka pulsuj¹ca) i czy mo¿na
otworzyæ pokrywê (wiat³o sta³e) (patrz str. 17).
Pokrêt³o PROGRAMY do nastawiania programów
(patrz str. 18).
W czasie trwania programu pokrêt³o pozostaje
nieruchome.
17
PL
Serwis
techniczny
Nieprawid³owoci
w dzia³aniu
Zasady
ostro¿noci
KonserwacjaProgramy rodki pior¹ceInstalacja Opis
Przyciski funkcyjne
PRZYCISKI FUNKCYJNE s³u¿¹ równie¿ jako
wiate³ka sygnalizuj¹ce.
Po wybraniu danej funkcji zawieci siê odpowiedni
przycisk.
Jeli wybrana funkcja nie mo¿e byæ nastawiona
razem z wybranym programem, przycisk funkcji
bêdzie migota³, a funkcja nie zostanie uruchomiona.
Jeli nastawiona zostanie funkcja sprzeczna z
uprzednio wybran¹ inn¹ funkcj¹, tylko jeden wybór
bêdzie przyjêty.
wiate³ka sygnalizuj¹ce
wiate³ka sygnalizuj¹ce dostarczaj¹ wa¿nych
informacji.
Informuj¹ one, co nastêpuje:
Aktualna faza prania:
W trakcie cyklu prania poszczególne wiate³ka
bêd¹ siê zapalaæ, wskazuj¹c stan zaawansowania
prania w toku:
Pranie wstêpne
Pranie
P³ukanie
Odwirowanie
Uwaga: w fazie usuwania wody zapali siê wiate³ko
odpowiadaj¹ce fazie Wirowania.
Fig. 1
Fig. 2
A) OTWIERANIE. (Rys.1). Podnieæ zewnêtrzn¹
pokrywê i ca³kowicie otworzyæ.
B) Nastêpnie otworzyæ bêben, pomagaj¹c sobie
obiema rêkami, jak pokazano na Rys. 2):
- przycisn¹æ wskazany strza³k¹ na Rys. 2
przycisk i lekko docisn¹æ w dó³, trzymaj¹c
opart¹ jedn¹ d³ón, aby drzwiczki otwieraj¹c siê
nie zrani³y palców;
- powoli poluzowaæ drzwiczki, które siê zwolni¹ i
³atwo otworz¹.
C) WK£ADANIE BIELIZNY. (Rys.3)
D) ZAMKNIÊCIE. (Rys.4)
- dobrze zamkn¹æ drzwiczki, opuszczaj¹c
najpierw drzwiczki przednie i opieraj¹c na nich
drzwiczki tylne;
- upewniæ siê, czy zaczepy przednich drzwiczek
dobrze wesz³y na swoje miejsce w tylnych
drzwiczkach;
- po us³yszeniu charakterystycznego clac, co
wiadczy o zaskoczeniu zaczepów, lekko
docisn¹æ oboje drzwiczek, które nie powinny siê
rozczepiæ.;
- na zakoñczenie zamkn¹æ klapê zewnêtrzn¹.
Jak otwieraæ i zamykac kosz
Fig. 3
Fig. 4
18
PL
Rodzaj tkaniny oraz stopieñ
zabrudzenia
Programy
Tempera-
tury
rodek pior¹cy
rodek
zmiêkczaj¹cy
Opcja
Wybielanie/
Wybielacz
Czas
trwania
cyklu
(minuty)
Opis cyklu prania
Pranie
wstêpne
Pranie
a
ciwe
Bawe³na
Bielizna bia³a silnie zabrudzona
(pociel, obrusy itp.)
1
90
°
C

137
Pranie wstêpne, pranie w³aciwe,
ukania, odwirowania porednie i
koñcowe
Bielizna bia³a silnie zabrudzona
(pociel, obrusy itp.)
2
90
°
C

Delikatne /
Tradycyjny
129
Pranie, ukania, odwirowania
porednie i koñcowe
Bielizna bia i kolorowa,
wytrzyma³a, mocno zabrudzona
3
60
°
C

Delikatne /
Tradycyjny
14
4
Pranie, ukania, odwirowania
porednie i koñcowe
Bielizna bia³a, s³abo zabrudzona
oraz kolorowa delikatna
(koszule, bluzki itp.)
4
40
°
C

Delikatne /
Tradycyjny
78
Pranie, ukania, odwirowania
porednie i koñcowe
Tkaniny kolorowe, delikatne,
ma³o zabrudzone
5
30
°
C

Delikatne /
Tradycyjny
7
0
Pranie, ukania, odwirowania
porednie i koñcowe
Tkaniny syntetyczne
Tkaniny syntetyczne o wytrzyma³ych
kolorach, silnie zabrudzone (bielizna
dla niemowl¹t itp.)
6
60
°
C

Delikatne 79
Pranie, ukania, funkcja
przeciw gnieceniu lub delikatne
odwirowanie
Tkaniny syntetyczne o wytrzyma³ych
kolorach, silnie zabrudzone (bielizna
dla niemowl¹t itp.)
7
50
°
C

Delikatne 75
Pranie, ukania, funkcja
przeciw gnieceniu lub delikatne
odwirowanie
Tkaniny syntetyczne o delikatnych
kolorach (wszystkie rodzaje
bielizny, lekko zabrudzonej)
8
40
°
C

Delikatne
6
5
Pranie, ukania, funkcja
przeciw gnieceniu lub delikatne
odwirowanie
Tkaniny syntetyczne o delikatnych
kolorach (wszystkie rodzaje
bielizny, lekko zabrudzonej)
9
30
°
C

30
Pranie, p³ukania i delikatne
odwirowanie
Tkaniny delikatne
We³na
10
40
°
C

Delikatne
4
5
Pranie, p³ukania i delikatne
odwirowanie
Ubrania i tkaniny wyj¹tkowo
delikatne (firanki, jedwab,
wiskoza itp.)
11
30
°
C

5
2
Pranie, ukania, funkcja
przeciw gnieceniu lub
opró¿nienie z wody
PROGRAMY CZ
Ê
CIOWE
ukanie

ukania i odwirowanie
ukanie delikatne

ukania, funkcja przeciw
gnieceniu lub opró¿nienie z wody
Odwirowanie
Opró¿nienie z wody i
energiczne odwirowanie
Odwirowanie delikatne
Op¿nienie z wody i delikatne
odwirowanie
Opró¿nienie z wody Opró¿nienie z wody
Uruchomienie i Programy
Tabela programów
Uwagi.
Opis funkcji przeciw gnieceniu siê tkanin, zobacz £atwiejsze prasowanie, na nastêpnej stronie. Podane w
tabeli dane maj¹ charakter przybli¿ony.
Program specjalny.
Dzienny 30' (program 9 dla tkanin syntetycznych) przeznaczony jest do prania bielizny ma³o zabrudzonej w krótkim
czasie: trwa tylko 30 minut i pozwala dziêki temu na zaoszczêdzenie energii i czasu.
Nastawiaj¹c program (9 o temperaturze 30°C) mo¿na razem wypraæ ró¿nego rodzaju tkaniny (z wyj¹tkiem we³ny i
jedwabiu), przy maksymalnym za³adunku do 3kg. Zalecamy stosowanie p³ynnego rodka pior¹cego.
Krótko mówi¹c: jak nastawiæ program
1. W³¹czyæ pralkê, przyciskaj¹c przycisk .
Wszystkie wiate³ka sygnalizacyjne zapal¹ siê
na kilka sekund, a nastêpnie zgasn¹, po czym
zacznie migotaæ wiate³ko sygnalizacyjne
W£¥CZENIE/ZABLOKOWANE DRZWICZKI.
2. W³o¿æ bielinê do pralki, wsypaæ proszek i
dodatki (patrz str. 20) i zamnkn¹æ pokrzwkê.
3. Nastawiæ po¿¹dany program przy pomocy
pokrêt³a PROGRAMÓW.
4. Nastawiæ temperaturê prania (zobacz str. 19).
5. Nastawiæ szybkoæ wirowania (zobacz str. 19).
6. Uruchomiæ program, przyciskaj¹c przycisk START/RESET.
Aby anulowaæ program, nale¿y trzymaæ przyciniêty
przycisk START/RESET przez conajmniej 2 sekundy.
7. Po zakoñczeniu programu wiate³o sygnalizacyjne
W£¥CZENIE/ZABLOKOWANE DRZWICZKI zacznie
migotaæ, co wskazuje, ¿e mo¿na otworzyæ
drzwiczki. Wyj¹æ bieliznê i pozostawiæ drzwiczki
pralki uchylone, aby bêben móg³ wyschn¹æ.
Wy³¹czyæ pralkê, przyciskaj¹c przycisk
.
19
PL
Funkcje Efekt Uwagi dotycz¹ce u¿ycia Opcja aktywna
przy
programach:
Super Wash Pozwala na
doskona³e
wypranie
bielizny; bielizna
jest
zdecydowanie
bielsza, ni¿ przy
standardowym
praniu w klasie
enegetycznej A.
Funkcji tej nie mo¿na nastawiæ razem z funkcj¹ PRANIE
B£YSKAWICZNE.
1, 2, 3, 4,
5, 6, 7, 8
£atwiejsze
prasowanie
Zmniejsza
gniecenie siê
tkanin,
u³atwiaj¹c
prasowanie.
Po nastawieniu tej funkcji programy 6, 7, 8, 11 oraz
Delikatne p³ukanie zatrzymaj¹ siê z bielizn¹ namoczon¹ w
wodzie (Funkcja zapobiegaj¹ca gnieceniu), a zacznie
migotwiate³ko sygnalizacyjne fazy P³ukania:
- aby zakoñczyæ cykl prania, nale¿y przycisn¹æ
przycisk START/RESET;
- aby wykonaæ tylko opró¿nienie z wody, ustawiæ
pokrêt³o na odpowiednim symbolu i
przycisn¹æ przycisk START/RESET.
Wszystkie poza
1, 2, 9, 10,
Opró¿nianie z
wody.
Pranie
b³yskawiczne
Zmniejsza o
oko³o 30% czas
trwania cyklu
prania.
Funkcji tej nie mo¿na nastawiæ razem z funkcj¹ SUPER
WASH.
1, 2, 3, 4,
5, 6, 7, 8
ukanie
ukanie
dodatkowe
Zwiêksza
skutecznoæ
p³ukania.
Zaleca siê stosowanie tej opcji przy pralce za³adowanej do
pe³na lub przy du¿ej iloci u¿ytego rodka pior¹cego.
1, 2, 3, 4,
5, 8,
P³ukania.
Potrzeby indywidualne
Serwis
techniczny
Nieprawid³owoci
w dzia³aniu
Zasady
ostro¿noci
KonserwacjaProgramy rodki pior¹ceInstalacja Opis
Nastawienie temperatury
Temperaturê prania nastawia siê, obracaj¹c pokrêt³o TEMPERATURY (zobacz Tabelê programów na str. 18).
Temperaturê mo¿na zredukowaæ, a¿ do prania w zimnej wodzie (
).
Nastawienie wirowania
Obracaj¹c pokrêt³o WIROWANIE, mo¿na nastawiæ szybkoæ odwirowywania dla wybranego programu.
Maksymalne szybkoci przewidziane dla wybranych programów nastêpuj¹ce:
Programy Maksymalna szybkoæ
Bawe³na 1000
obrotów na minutê
Tkaniny syntetyczne 800 obrotów na minutê
We³na 600 obrotów na minutê
Jedwab no
Szybkoæ wirowania mo¿e zostaæ zmniejszona lub mo¿na wirowanie zupe³nie wykluczyæ przez przyciniêcie
przycisku
.
Pralka zapobiegnie automatycznie wykonaniu wirowania szybszego, ni¿ maksymalne wirowanie przewidziane dla
wybranego programu.
W celu unikniecia nadmiernych wibracji przed kazdym odwirowaniem pralka rozklada ciezar wsadu w sposób
jednolity, nastepuje to poprzez wykonywanie stalych obrotów kosza z predkoscia nieco wyzsza od obrotów podczas
prania. Kiedy jednak, niezaleznie od powtarzanych prób, wsad nie zostanie rozlozony równomiernie, maszyna
wykona wirowanie z predkoscia nizsza od zaprogramowanej. W przypadku pojawienia sie nadmiernego
niezrównowazenia maszyna bedzie próbowala rozlozyc wsad zamiast odwirowywac.
Ewentualne próby zrównowazenia wsadu moga wydluzyc laczny czas trwania cyklu o maksimum 10 minut.
Funkcje
Ró¿ne funkcje, w jakie wyposa¿ona jest pralka, pozwalaj¹ na osi¹gniêcie po¿¹danych rezultatów prania. Aby
uaktywniæ poszczególne funkcje, nale¿y postêpowaæ w nastêpuj¹cy sposób:
1. przycisn¹æ odpowiadaj¹cy po¿¹danej funkcji przycisk, zgodnie z poni¿sz¹ tabel¹;
2. zawiecenie siê odpowiedniego przycisku oznacza, ¿e funkcja jest aktywna.
Uwaga: Szybkie migotanie przycisku oznacza, ¿e danej funkcji nie mo¿na nastawiæ przy wybranym programie.
20
PL
Szufladka na rodki pior¹ce
Dobre rezultaty prania zale¿¹ równie¿ od
w³aciwego dozowania rodka pior¹cego: wsypuj¹c go
za du¿o, wcale nie poprawia siê wydajnoci prania,
lecz przyczynia siê do
odk³adania siê nalotów
na wewnêtrznych
czeciach pralki i do
zanieczyszczania
rodowiska.
Wysun¹æ szufladkê i
wsypaæ do niej rodki
pior¹ce i dodatkowe w
nastêpuj¹cy sposób
przegródka 1: rodek pior¹cy do prania wstêpnego
(w proszku)
przegródka 2: rodek pior¹cy
(w proszku lub w p³ynie)
rodek pior¹cy w p³ynie nale¿y w³o¿yæ
bezporednio do bêbna z zastosowaniem
odpowiedniej kulki dozuj¹cej.
przegródka 3: rodki dodatkowe
(zmiêkczaj¹ce, itp.)
Kiedy wlewa siê rodek zmiêkczaj¹cy do przegródki 3,
to nale¿y zwróciæ uwagê, aby nie przekroczyæ
oznaczonego poziomu "max".
rodek zmiêkczaj¹cy jest automatycznie dodawany do
wody podczas ostatniego p³ukania. Na zakoñczenie
tego programu prania w przegródce 3 pozostaje reszta
wody. S³u¿y ona dla skoncentrowanych rodków
zmiêkczaj¹cych, to znaczy do ich rozprowadzenia z
wod¹. Jeliby w przegródce 3 pozosta³o wiêcej wody
ni¿ zwykle, oznacza to, ¿e urz¹dzenie dozuj¹ce jest
zatkane. Jak je wyczyciæ patrz strona 22.
przegródka 4: Wybielacz
Nie u¿ywaæ rodków do prania rêcznego,
poniewa¿ tworz¹ za du¿o piany.
Cykl wybielania
Tradycyjnego wybielacza u¿ywa siê do bia³ych
tkanin wytrzyma³ych, delikatnego - do tkanin
kolorowych, syntetycznych i do we³ny.
Przy wlewaniu wybielacza nie nale¿y przekroczyæ
poziomu max" wskazanego na rodkowej oce
(zobacz rysunek).
Aby przeprowadziæ tylko samo wybielanie, nale¿y
wlaæ wybielacz do pojemniczka dodatkowego 4 i
nastawiæ program P³ukanie
(dla tkanin
bawe³nianych) lub P³ukanie delikatne
(dla tkanin
syntetycznych).
Przygotowanie bielizny
Podzieliæ bieliznê do prania wed³ug:
- rodzaju tkaniny / symbolu na etykietce.
- kolorów: oddzieliæ bieliznê kolorow¹ od bia³ej.
Opró¿niæ kieszenie i sprawdziæ guziki.
Nie przekraczaæ wskazanego ciê¿aru bielizny
suchej:
Tkaniny wytrzyma³e: max 5 kg
Tkaniny syntetyczne: max 2,5 kg
Tkaniny delikatne: max 2 kg
We³na: max 1 kg
Ile wa¿y bielizna?
1 przecierad³o 400-500 gr.
1 pow³oczka na poduszkê 150-200 gr.
1 obrus 400-500 gr.
1 szlafrok 900-1.200 gr.
1 rêcznik 150-250 gr.
Tkaniny wymagaj¹ce szczególnej dba³oci
Firanki: w³o¿yæ je z³o¿one do poszewki lub do
siatkowatego worka. Praæ same, nie przekraczaj¹c
po³owy za³adunku. Stosowaæ program 11, który
automatycznie wyklucza wirowanie.
Poduszki i kurtki: Jeli wype³nione one pierzem
gêsim lub kaczym, mo¿na je praæ w pralce. Wywróciæ
na lew¹ stronê i za³adowaæ nie wiêcej ni¿ 2-3 kg;
powtórzyæ p³ukania jeden lub dwa razy i stosowaæ
delikatne odwirowanie.
Tenisówki: oczyciæ z b³ota. Mo¿na je praæ razem z
d¿insami i bielizn¹ wytrzyma³¹, lecz nie bia³¹.
We³na: Aby uzyskaæ dobre rezultaty prania, nale¿y
stosowaæ specjalny rodek pior¹cy i nie
przekraczaæ 1 kg za³adunku.
Woolmark Platinum Care
Program delikatny jak pranie rêczne.
Ariston wprowadzi³ nowy standard prania o
doskona³ych rezultatach, który zdoby³ sobie
uznanie Stowarzyszenia Czystej ¯ywej We³ny (The
Woolmak Company) przez przyznanie presti¿owej
marki Woolmark Platinum Care. Jeli na Waszej pralce
znajduje siê znak firmowy Woolmark Platinum Care, mo¿na w
niej praæ, uzyskuj¹c doskona³e rezultaty, ubrania we³niane z
etykietk¹ Praæ rêcznie (M.0303):
Nastawiæ program 10 dla wszyskich ubrañ nosz¹cych
etykietkê Praæ rêcznie
, stosuj¹c specjalne
rodki pior¹ce (max 1 Kg).
rodki pior¹ce i bielizna
1 / 1

Whirlpool AVTL 104 (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka