Indesit WITP 821 (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
1
GB
WASHING MACHINE
WITP 821
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Electric and water connections
The first wash cycle
Technical details
Washing machine description, 4-5
Control panel
How to open and shut the drum
Leds
Starting and Programmes, 6
Briefly: how to start a programme
Programme table
Personalisations, 7
Setting the temperature
Functions
Detergents and laundry, 8
Detergent dispenser
Bleach cycle
Preparing your laundry
Special items
Precautions and advice, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning your appliance
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
Cleaning the detergent dispenser
Troubleshooting, 11
Service, 12
Before calling for Assistance
English, 1
GB
FR
Română, 49
RO
CZ
Český, 25
Slovenský, 37
SK
Français, 13
2
GB
! Keep this instruction manual in a safe place for future refe-
rence. Should the appliance be sold, transferred or moved,
make sure the instruction manual accompanies the washing
machine to inform the new owner as to its operation and
features.
! Read these instructions carefully: they contain vital infor-
mation on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washing
machine.
2. Check whether the
washing machine has been
damaged during transport.
If this is the case, do not
install it and contact your
retailer.
3. Remove the four protec-
tive screws and the rubber
washer with the respective
spacer, situated on the
rear of the appliance (see
figure).
4. Seal the gaps using the
plastic plugs provided.
5. Keep all the parts: you will need them again if the washing
machine needs to be moved to another location.
Warning: should the screws be re-used, make sure you fasten
the shorter ones at the top.
! Packaging materials are not children’s toys.
Levelling
1. Install the washing machine
on a flat sturdy floor, without
resting it up against walls,
furniture cabinets or other.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening or lo-
osening the adjustable front feet
(see figure); the angle of inclina-
tion, measured according to the
worktop, must not exceed .
Levelling your appliance correctly will provide it with stability
and avoid any vibrations, noise and shifting during operation.
If it is placed on a fitted or loose carpet, adjust the feet in
such a way as to allow enough room for ventilation beneath
the washing machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it is
perfectly clear.
2. Connect the other end of
the water inlet hose to the
washing machine,
screwing it onto the applian-
ces cold water inlet, situated
on the top right-hand side
on the rear of the appliance
(see figure).
3. Make sure there are
no kinks or bends in the
hose.
! The water pressure at the tap must be within the values
indicated in the Technical details table
(on the next page).
! If the water inlet hose is not long enough, contact a
specialist store or an authorised serviceman.
! Never use hoses that have already been used.
Installation
3
GB
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between 65
and 100 cm from the floor;
alternatively, place it over
the edge of a basin, sink
or tub, fastening the duct
supplied to the tap (see
figure). The free end of
the hose should not be
underwater.
! We advise against the use of hose extensions; in case
of absolute need, the extension must have the same
diameter as the original hose and must not exceed 150
cm in length.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance’s
maximum power load indicated in the Technical
details table (on the right);
the supply voltage is included within the values i
ndicated on the Technical details table
(on the right);
the socket is compatible with the washing
machine’s plug. If this is not the case, replace
the socket or the plug.
! The washing machine should not be installed in an ou-
tdoor environment, not even when the area is sheltered,
because it may be very dangerous to leave it exposed to
rain and thunderstorms.
! When the washing machine is installed, the mains so-
cket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or dange-
rously compressed.
! The power supply cable must only be replaced by an
authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before you
use it for the first time, run a wash cycle with detergent
and no laundry, setting the 90°C programme without a
pre-wash cycle.
65 - 100 cm
Technical details
Model
WITP 821
Dimensions
40 cm wide
85 cm high
60 cm deep
Capacity
from 1 to 5 kg
Electric
connections
Please refer to the technical data plate
fixed to the machine.
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 42 litres
Spin speed
up to 800 rpm
Test wash
cycles in
accordance
with directives
1061/2010 and
1015/2010.
Programme : Cotton standard 60°C;
Programme : Cotton standard 40°C.
This appliance is compliant with
the following European Community
Directives:
- 2004/108/CE (Electromagnetic
Compatibility)
- 2006/95/CE (Low Voltage)
- 2002/96/CE
4
GB
ON-OFF/LID LOCK led:
If this LED is on, the appliance Lid is locked to prevent it from being opened accidentally; to avoid any damages, you must
wait for the lamp to flash before you open the Lid.
.
! The rapid flashing of the ON-OFF/LID LOCK Led together with the flashing of at least one other LED indicates there is an
abnormality (see page 11).
Control panel
Washing machine description
ON/OFF
button
TEMPERATURE
knob
START/RESET
button
FUNCTION
Buttons
PROGRAMME
knob
LEDs
LID LOCKED
LED
Detergent dispenser to add detergent and fabric sof-
tener (see page 8).
LEDs to find out which wash cycle phase is under way (see
page 5).
FUNCTION keys to select the functions available.
The button corresponding to the function selected will
remain on.
TEMPERATURE knob to set the temperature or the cold
wash cycle (see page 7).
ON/OFF key to turn the washing machine on and off.
START/RESET key to start the programmes or cancel
incorrect settings.
ON-OFF/LID LOCK led, to find out whether the washing
machine is on (flashing) and if the lid may be opened (see
page 5).
PROGRAMME knob to set the programmes (see page 6).
The knob stays still during the cycle.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON/OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W
5
GB
Fig. 1
Fig. 2
A) Opening (Fig. 1).
Lift the external lid and open it completely.
B) Then open the drum using both hands as
shown in Fig. 2:
- press the button indicated by the arrow in Fig. 2 lightly
downwards, with one hand firmly resting on the doors to
prevent them from suddenly opening and hurting your fingers;
- therefore follow the appliance doors along as these unhook
and open easily.
C) Loading the washing machine. (Fig. 3).
D) Shutting (Fig. 4).
- close the drum fully by first shutting the front door
followed by the rear one;
- then ensure the hooks on the front door are perfectly
housed within the seat of the rear door;
- after the hooks have clicked into position, press both
doors lightly downwards to make sure they do not
come loose;
- finally shut the external lid.
How to open and to close the drum
Fig. 3
Fig. 4
Function buttons
The FUNCTION BUTTONS also act like LEDS.
When a function is selected, the corresponding button is
illuminated.
If the function selected is incompatible with the program-
me set, the button will flash and the function will not be
enabled.
If you set a function that is incompatible with another fun-
ction you selected previously, only the last one selected
will be enabled.
Leds
The LEDS provide important information.
This is what they can tell you:
Cycle phase under way:
During the wash cycle, the LEDs gradually illuminate on
to indicate the cycle phase under way:
Prewash
Wash
Rinse
Spin cycle
Note: during draining, the LED corresponding to the Spin
cycle phase will be turned on.
6
GB
Starting and Programmes
Programme table
Briefly: starting a programme
1. Switch the washing machine on by pressing button .
All the LEDS will light up for a few seconds and
the ON-OFF/DOOR LOCK Led will begin to flash.
2. Load your laundry into the washing machine, add
the detergent and any fabric softener (see page 8)
and shut the appliance door.
3. Set the PROGRAMME knob to the programme required.
4. Set the wash temperature (see page 7).
5. Start he programme by pressing the START/RESET
button. To cancel it, keep the START/RESET button
pressed for at least 2 seconds.
6. When the programme is finished, the ON-OFF/
DOOR LOCK Led will flash to indicate that the
appliance door can be opened. Take out your
laundry and leave the appliance door ajar to allow
the drum to dry thoroughly. Turn the washing
machine off by pressing button .
Notes
For the anti-crease function: see opposite page. The information contained in the table is purely indicative.
Cotton Standard 20°C (wash cycle 5) ideal for heavily soiled cotton loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying
speed, with repeated and frequent peaks.
Express (programme
9
for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts
30 minutes and allows you to save on both time and energy. By setting this programme (
9
at 30°C), you can wash different
fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
We recommend the use of liquid detergent.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness
%
Energy
consumption
kWh
Total water lt
Cycle
duration
Pre-
wash
Wash
Fabric
softener
Ble-
ach
Cotton
1
Cotton with prewash: extremely soiled whites. 90° 800
- 5 71 1,82 64 150’
2
Cotton: extremely soiled whites. 90° 800 -
5 71 1,90 60 135’
Cotton Standard 60°C (1): heavily soiled whites and resistant colours. 60° 800 -
5 71 0,88 47,5 160’
Cotton Standard 40°C (2): lightly soiled whites and delicate colours. 40° 800 -
5 71 1,09 92 150’
5 Cotton Standard 20°C
20° 800 -
5 - - - 180’
Synthetics
6
Synthetics: heavily soiled fast colours (baby linen, etc.) 60° 800 -
3 44 0,85 39 110’
6
Synthetics (3): heavily soiled fast colours (baby linen, etc.) 40° 800 -
3 44 0,53 39 100’
7
Synthetics: heavily soiled fast colours (baby linen, etc.) 50° 800 -
3 - - - 105’
8
Synthetics: Delicate colours (all types of slightly soiled garments) 40° 800 -
3 - - - 75’
9
Express: to refresh lightly soiled garments quickly (not suitable for wool, silk
and clothes which require washing by hand).
30° 800 -
- 3 71 0,25 33 30’
Delicate
10
Wool: for wool, cashmere, etc. 40° 800 -
- 1 - - - 65’
11
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
- 1 - - - 55’
Partial programmes
Rinse - 800 - -
5 - - - 36’
Delicate rinse cycle - 800 - -
5 - - - 31
Spin cycle - 800 - - - - 5 - - - 16’
Delicate spin cycle - 800 - - - - 5 - - - 12’
Draining - 0 - - - - 5 - - - 2’
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 6; with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
7
GB
Personalisations
C
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
The temperature can be lowered, or even set to a cold wash ( ).
Note. To avoid excessive vibrations, before every spin cycle the machine distributes the load in a uniform manner by conti-
nuously rotating the drum at a speed which is slightly faster than the normal washing speed.
When, despite repeated attempts, the load is still not evenly distributed, the machine spins at a lower speed than the set
frequency.
If the load is excessively unbalanced, the machine attempts to distribute it instead of spinning.
The balancing attempts may extend the total duration of the cycle, up to a maximum of 10 minutes.
Functions
To enable a function:
1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.
Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Option Effect Comments Enabled with
programmes:
Bleaching
Bleaching cycle de-
signed to remove the
toughest stains.
Please remember to pour the bleach into extra compartment 4
(see page 8).
2,
, , 5,
6, 7, 8, Rinse
cycles.
Extra Rinse
Increases the efficien-
cy of the rinse.
Recommended when the appliance has a full load or with large
quantities of detergent.
1, 2, , ,
5, 6, 7, 8, 10,
11 and Rinse
cycles.
800
400
Reduces the spin
speed.
All program-
mes except
for 11 and
draining.
Anti-crease
Reduces fabric crea-
sing, making ironing
easier.
Setting this function will interrupt programmes 11 with a laundry
soak (Anti-crease) and the Rinse phase indicator light will blink.
To complete the cycle, press the Anti-crease button.
1, 2,
, , 5,
6, 7, 8, 11.
8
GB
Detergent dispenser
Good washing results also depend on the correct dose of
detergent: adding too much detergent won’t necessarily
make for a more efficient wash, and may in fact cause build
up on the interior of your appliance and even pollute the
environment.
! Do not use hand washing detergents because these crea-
te too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open up the detergent
dispenser and pour in the
detergent and fabric softe-
ner, as follows.
compartment 1: Detergent for pre-wash (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately prior
to the wash cycle start.
compartment 3: Additives (fabric softeners, etc.)
When pouring the softener in compartment 3, avoid excee-
ding the “max” level indicated.
The softener is added automatically into the machine during
the last wash. At the end of the wash programme, some
water will be left in compartment 3. This is used for the inlet
of denser fabric softeners into the machine, i.e. to dilute the
more concentrated softeners. Should more than a normal
amount of water remain in compartment 3, this means the
emptying device is blocked. For cleaning instructions, see
page 10. The fabric softener should not overflow from the
grid.
compartment 4: Bleach
Bleach cycle
Traditional bleach should be used on sturdy white fabrics,
and delicate bleach for coloured fabrics, synthetics and for
wool.
When pouring in the bleach, be careful not to exceed the
“max” level indicated on compartment 4 (see figure).
To run the bleach cycle alone, pour the bleach into com-
partment 4 and set the Rinse programme (for cotton
fabrics) and push the button Bleaching.
Preparing your laundry
Divide your laundry according to:
- the type of fabric/the symbol on the label.
- the colours: separate coloured garments from whites.
Empty all pockets and check for loose buttons.
Do not exceed theweight limits stated below,
which refer to the weight when dry:
Sturdy fabrics: max 5 kg
Synthetic fabrics: max 2.5 kg
Delicate fabrics: max 2 kg
Wool: max 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1,200 g
1 towel 150-250 g
Special items
Curtains: fold curtains and place them in a pillow case or
mesh bag. Wash them separately without exceeding half
the appliance load. Use programme 11 which excludes
the spin cycle automatically.
Wool: for best results, use a specific detergent, taking
care not to exceed a load of 1 kg.
Detergents and laundry
9
GB
Precautions and advice
! The washing machine was designed and built in com-
pliance with the applicable international safety regula-
tions. The following information is provided for your safety
and should consequently be read carefully.
General safety
This appliance has been designed for non-
professional, household use and its functions must
not be changed.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and know-
ledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervi-
sed to ensure that they do not play with the appliance.
This washing machine should only be used by
adults and in accordance with the instructions
provided in this manual.
Never touch the washing machine when barefoot
or with wet or damp hands or feet.
Do not pull on the power supply cable to unplug
the appliance from the electricity socket. Pull the
plug out yourself.
Do not touch the drain water as it could reach
very high temperatures.
Never force the washing machine door: this could
damage the safety lock mechanism designed to
prevent any accidental openings.
In the event of a malfunction, do not under any
circumstances touch internal parts in order to
attempt repairs.
Always keep children well away from the
appliance while in operation.
Should it have to be moved, proceed with the
help of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
Before loading your laundry into the washing
machine, make sure the drum is empty.
Disposal
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream.
Old appliances must be collected separately in order to
optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on
the product reminds you of your obligation, that when you
dispose of the appliance it must be separately collected.
Consumers may take their old appliance to public waste
collection areas, other communal collection areas, or if
national legislation allows return it to a retailer when pur-
chasing a similar new product.
All major household appliance manufacturers are active
in the creation of systems to manage the collection and
disposal of old appliances.
Saving energy and respecting the
environment
Environmentally-friendly technology
If you only see a little water through your appliance door,
this is because thanks to the latest technology, your
washing machine only needs less than half the amount
of water to get the best results: an objective reached to
respect the environment.
Saving on detergent, water, energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15% energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on energy.
Use the correct quantity of detergent depending on
the water hardness, how soiled the garments are and
the amount of laundry you have, to avoid wastage and
to protect the environment: despite being biodegra-
dable, detergents do contain ingredients that alter the
natural balance of the environment. In addition, avoid
using fabric softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board’s peak load.
If your laundry has to be dried in a tumble dryer,
select a high spin speed. Having the least water
possible in your laundry will save you time and
energy in the drying process.
10
GB
Care and maintenance
Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear
of your appliances water system and also prevent leaks.
Unplug your appliance when cleaning it and during all
maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can be cle-
aned with a soft cloth soaked in lukewarm soapy water. Do
not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see
figure). Wash it under running water; this operation should
be repeated frequently.
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unplea-
sant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump that
does not require any maintenance. Sometimes, small items
(such as coins or buttons) may fall into the pre-chamber that
protects the pump, situated in the lower part of the same.
! Make sure the wash cycle has ended and unplug the
appliance.
To recover any objects that have fallen into the pre-
chamber:
1. remove the plinth at
the bottom on the front
side of the washing
machine by pulling from
the side with your hands
(see figure);
2. unscrew the lid
rotating it anticlock-wise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the interior
thoroughly;
4. screw the lid back on;
5. reposition the panel,
making sure the hooks
are securely in place
before you push it onto
the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you
see any cracks, replace it immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use hoses that have already been used.
How to clean the detergent dispenser
Fig. 1
Fig. 2
Cleaning:
Then clean the dispenser under a tap (fig. 3) using an old
toothbrush and, once the pair of siphons inserted in the
top of compartments 1 and 2 (fig. 4) have been pulled
out, check whether the same are not clogged and then
rinse them.
Reassembly:
Do not forget to reinsert
the pair of siphons into the
special housings and then to
replace the dispenser into its
seat, clicking it into place (fig.
4, 2 and 1).
Disassembly:
Press lightly on the large
button on the front of the
detergent dispenser and pull
it upwards (fig. 1).
Fig. 3
Fig. 4
11
GB
Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem can’t easily
be solved by consulting the following list.
Troubleshooting
Problem
The washing machine won’t start.
The wash cycle won’t start.
The washing machine fails to load
water.
The washing machine continuou-
sly loads and unloads water.
The washing machine does not
drain or spin.
The washing machine vibrates too
much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led
flashes rapidly at the same time
as at least one other LED.
There is too much foam.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to
make contact.
There has been a power failure.
The appliance door is not shut properly. The Lid locked Led flashes.
The button has not been pressed.
The START/RESET button has not been pressed.
The water tap is not turned on.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap is not turned on.
There is a water shortage.
The water pressure is insufficient.
The START/RESET button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor
(see page 3).
The free end of the hose is underwater (see page 3).
The wall drainage system doesn’t have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and call for Assistance. If the dwelling is on one of the upper floors of
a building, there may be drain trap problems causing the washing machine to load
and unload water continuously. In order to avoid such an inconvenience, special
anti-drain trap valves are available in shops.
The programme does not foresee the draining: some programmes
require enabling the draining manually (see page 6).
The Anti-crease option is enabled: to complete the programme, press
the START/RESET button (see page 7).
The drain hose is bent (see page 3).
The drain duct is clogged.
The drum was not unblocked correctly during installation (see page 2).
The washing machine is not level (see page 2).
The washing machine is closed in between furniture cabinets and
the wall (see page 2).
The water inlet hose is not screwed on correctly (see page 2).
The detergent dispenser is obstructed (to clean it, see page 10).
The drain hose is not secured properly (see page 3).
Switch off the machine and unplug the appliance; wait for
approximately 1 minute then switch it on again.
If the problem persists, contact Assistance.
The detergent is not suitable for machine washing (it should bear
the definition “for washing machines” orhand and machine wash”,or the like).
You used too much detergent.
12
GB
Before calling for Assistance:
Check whether you can solve the problem on your own (see page 11);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Service Centre on the telephone number
provided on the guarantee certificate.
! Always request the assistance of authorised servicemen.
Notify the operator of:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
Service
13
F
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements hydrauliques et électriques
Premier cycle de lavage
Caractéristiques techniques
Description du lave-linge, 16-17
Bandeau de commandes
Comment ouvrir et fermer le tambour
Voyants
Mise en marche et Programmes, 18
En bref: démarrage d’un programme
Tableau des programmes
Personnalisations, 19
Sélection de la température
Fonctions
Produits lessiviels et linge, 20
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Pièces de linge particulières
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Economies et respect de l’environnement
Entretien et soin, 22
Coupure de l’arrivée d’eau et de courant
Nettoyage du lave-linge
Entretien du couvercle et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Nettoyage du tiroir à produits lessiviels
Anomalies et remèdes, 23
Assistance, 24
Consultation à tout moment
LAVE-LINGE
WITP 821
Mode d’emploi
F
14
F
Installation
! Conservez ce mode d’emploi pour pouvoir le consulter à
tout moment. En cas de vente, de cession ou de déména-
gement, veillez à ce qu’il suive toujours le lave-linge pour
que son nouveau propriétaire soit informé sur son mode de
fonctionnement et puisse profiter des conseils correspon-
dants.
! Lisez attentivement les instructions: elles fournissent
d’importantes informations sur l’installation, l’utilisation et la
sécurité.
Déballage et mise à niveau
Déballage: enlever les 4 vis
1. Déballez le lave-linge.
2. Contrôlez que le lave-lin-
ge n’a pas été endommagé
pendant le transport. S’il est
abîmé, ne le raccordez pas
et contactez votre reven-
deur.
3. Enlevez les quatre vis de
protection pour le transport,
le caoutchouc et la cale,
placés dans la partie arrière
(voir figure).
4. Bouchez les trous à l’aide
des bouchons plastique
fournis.
5. Conservez bien toutes ces pièces: il faudra les remonter
en cas de transport du lave-linge.
! Attention: en cas de réutilisation, les vis plus courtes
doivent être montées dessus.
! Les emballages ne sont pas des jouets pour enfants.
Mise à niveau
Votre appareil peut s’avérer bruyant si vous n’avez pas bien
réglé ses deux pieds avant.
1. Installez le lave-linge sur
un sol plat et rigide, sans
l’appuyer contre des murs,
des meubles ou autre.
2. Si le sol n’est pas par-
faitement horizontal, vissez
ou dévissez les petits pieds
avant (voir figure) pour niveler
l’appareil; son angle d’incli-
naison, mesuré sur le plan de
travail, ne doit pas dépasser
2°.
Une bonne mise à niveau garantit la stabilité de la machine
et évite qu’il y ait des vibrations, du bruit et des déplace-
ments en cours de fonctionnement.
Si la machine est posée sur de la moquette ou un tapis,
réglez les petits pieds de manière à ce qu’il y ait suffisam-
ment d’espace pour assurer une bonne ventilation.
Raccordements hydrauliques et
électriques
Raccordement du tuyau d’arrivée de l’eau
1. Reliez le tuyau d’ali-
mentation en le vissant à
un robinet d’eau froide à
embout fileté 3/4 gaz (voir
figure).
Faire couler l’eau jusqu’à
ce qu’elle soit limpide et
sans impuretés avant de
raccorder.
2. Raccordez le tuyau
d’alimentation au lave-
linge en le vissant à la
prise d’eau prévue, dans
la partie arrière en haut à
droite (voir figure).
3. Faites attention à ce
que le tuyau ne soit ni plié
ni écrasé.
! La pression de l’eau doit être comprise entre les valeurs
indiquées dans le tableau des Caractéristiques techni-
ques (voir page ci-contre).
! Si la longueur du tuyau d’alimentation ne suffit pas,
adressez-vous à un magasin spécialisé ou à un techni-
cien agréé.
15
F
Raccordement du tuyau de vidange
Raccordez le tuyau d’éva-
cuation, sans le plier, à un
conduit d’évacuation ou
à une évacuation murale
placés à une distance du
sol comprise entre 65 et
100 cm;
ou bien accrochez-le à un
évier ou à une baignoire,
dans ce cas, fixez le sup-
port en plastique fourni
avec l’appareil au robinet
(voir figure). L’extrémité li-
bre du tuyau d’évacuation
ne doit pas être plongée
dans l’eau.
! L’utilisation de tuyaux de rallonge est absolument
déconseillée, si vous ne pouvez vraiment pas faire autre-
ment vous devrez utiliser un tuyau de même diamètre et
de longueur maximum de 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant,
contrôlez que:
la prise dispose de mise à la terre et est conforme aux
normes;
la prise est bien apte à supporter la puissance ma-
ximale de la machine indiquée dans le tableau des
Carcatéristiques techniques (voir ci-contre);
la tension d’alimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche du lave-linge.
Autrement, remplacez la prise ou la fiche.
! Votre lave-linge ne doit pas être installé dehors, même
à l’abri, car il est très dangereux de le laisser exposé à la
pluie et aux orages.
! Après installation du lave-linge, la prise de courant doit
être facilement accessible.
! N’utilisez ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni écrasé.
! Le câble d’alimentation ne doit être remplacé que par
des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas de
non respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première utilisation de la machine, effectuez un
cycle de lavage avec un produit lessiviel mais sans linge
et sélectionnez le programme à 90°C sans prélavage.
65 - 100 cm
Caractéristiques techniques
Modèle
WITP 821
Dimensions
largeur 40 cm
hauteur 85 cm
profondeur 60 cm
Capacité
de 1 à 5 kg
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine.
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 42 litres
Vitesse
d’essorage
jusqu’à 800 tours minute
Programmes de
contrôle selon
les directives
1061/2010 et
1015/2010.
programme
; programme coton
standard à 60 °C;
programme ; programme coton
standard à 40 °C;
Cet appareil est conforme aux Directi-
ves Communautaires suivantes:
- 2004/108/CE (Compatibilité électro-
magnétique)
- 2006/95/CE (Basse Tension)
- 2002/96/CE
16
F
Bandeau de commandes
Description du lave-linge
Tiroir à produits lessiviels: chargement des produits
lessiviels et additifs (voir page 20).
Voyants: suivi du stade d’avancement du programme de
lavage. (voir page 17).
Touches FONCTION: sélection des fonctions disponibles.
La touche correspondant à la fonction sélectionnée restera
allumée.
Bouton TEMPÉRATURE: sélection de la température ou
lavage à froid (voir page 19).
Touche MISE EN MARCHE/ARRET: mise en marche ou
arrêt du lave-linge.
Touche START/RESET: démarrage des programmes ou
annulation (en cas d’erreur).
Voyant ALLUMAGE/COUVERCLE VERROUILLE:
pour comprendre si le lave-linge est branché et si le cou-
vercle peut être ouvert (voir page 17).
Bouton PROGRAMMES: choix des programmes (voir
page 18).
En cours de lavage, le bouton ne bouge pas.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est
équipée d’un système d’extinction automatique (veille)
activé après 30 minutes environ d’inutilisation. Appuyez
brièvement sur la touche
MISE EN MARCHE/ARRET
et
attendre que la machine soit réactivée.
Consommation en off-mode : 0,5 W
Consommation en Left-on : 0,5 W
Voyant ALLUMAGE/COUVERCLE VERROUILLE:
Le voyant allumé indique que le couvercle est verrouillé pour empêcher toute ouverture accidentelle; attendez que le voyant
cesse de clignoter avant d’ouvrir le hublot, vous risqueriez d’endommager l’appareil.
! Le clignotement rapide du voyant ALLUMAGE/COUVERCLE VERROUILLE en même temps qu’un autre signale une ano-
malie (voir page 23, Anomalies et Remédes).
Touche
MISE EN MARCHE/
ARRET
Touche
START/RESET
Bouton
TEMPÉRATURE
Bouton
PROGRAMMES
Voyants
Touches
FONCTION
Voyant
ALLUMAGE/
COUVERCLE
VERROUILLE
17
F
Voyants
Les voyants fournissent des informations importantes.
Voilà ce qu’ils signalent:
Phases en cours:
Pendant le cycle de lavage, les voyants s’allument pro-
gressivement pour indiquer son stade d’avancement:
Prélavage
Lavage
Rinçage
Essorage
Remarque: pendant la phase de vidange, le voyant corre-
spondant à la phase Essorage s’allume.
Touches fonction
Les TOUCHES FONCTION servent aussi de voyants.
Lalection d’une fonction entrne l’allumage du voyant
correspondant.
Si la fonction lectione est incompatible avec le pro-
gramme sélectionné, la touche clignote et la fonction n’est
pas activée.
En cas de sélection d’une fonction incompatible avec une
autre précédemment sélectionnée, la seule à être activée
sera la dernière validée.
A) Ouvrez le couvercle (Fig. 1):
Soulevez le Couvercle externe et ouvrez le complètement;
B) Ouvrez ensuite les Portes du tambour à l’aide de
vos deux mains comme indiqué sur la (Fig. 2):
• appuyez sur la touche indiquée par la flèche sur la Fig. 2 et
tout en appuyant légèrement vers le bas posez une main
pour éviter que les portes ne vous fassent mal aux adoigts
en s’ouvrant soudainement;
accompagnez dans leur mouvements les portes qui se
décrocheront et s’ouvriront facilement.
C) INTRODUISEZ LE LINGE (Fig. 3).
D) FERMEZ (Fig. 4):
• refermez bien le tambour en baissant d’abord la porte an-
térieure et posez ensuite la porte postérieure;
faites attention à parfaitement positionner les crochets de la
porte antérieure dans leur siège dans la porte postérieure;
• vous entendrez un “ clac ” qui confirmera la bonne fixation;
appuyez alors légèrement vers le bas sur les deux portes
qui ne doivent pas se décrocher;
• fermez enfin le couvercle externe.
Comment ouvrir et fermer le tambour
Fig. 1
Fig. 2
Fig. 3 Fig. 4
18
F
En bref: démarrage d’un programme
1. Pour allumer le lave-linge appuyez sur la touche . Tous les
voyants s’allument pendant quelques secondes puis s’étei-
gnent et le voyant ALLUMAGE/COUVERCLE VERROUILLE
commence à clignoter.
2. Chargez le lave-linge, versez le produit lessiviel et les additifs
(voir page 20) et fermez les portes et le couvercle.
3. Sélectionnez à l’aide du bouton PROGRAMMES le pro-
gramme désiré.
Mise en marche et Programmes
4. Sélectionnez la temrature de lavage (voir page 19).
5. Appuyez sur la touche START/RESET pour lancer le
programme.Pour annuler, poussez sur la touche START/
RESET pendant 2 secondes au moins.
6. A la fin du programme de lavage, le voyant ALLUMAGE/COU-
VERCLE VERROUILLE clignote pour indiquer que le
couvercle peut être ouvert. Sortez le linge et laissez le
couvercle entrouvert pour faire sécher le tambour. Etei-
gnez le lave-linge en appuyant sur la touche .
Tableau des programmes
Remarque
Pour la fonction anti-froissement: voir
Arrêt cuve pleine
, page ci-contre. Les données reportées dans le tableau sont à titre
indicatif.
Programme coton standard à 20 °C (programme 5): idéal pour des charges de linge sale en coton. Les bonnes performances,
même à froid, comparables à celles d’un lavage à 40°, sont assurées grâce à une action mécanique qui brasse en variant la vitesse
et avec des pics répétés et rapprochés.
Express (programme 9 pour Synthétiques) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 30
minutes et permet ainsi de faire des économies d’énergie et de temps. Choisissez le programme (9 à 30°C), vous pourrez laver ensem-
ble des textiles différents (sauf laine et soie) en ne dépassant pas 3 kg de charge. Nous vous conseillons d’utiliser des lessives liquides.
La durée du cycle indiquée sur l’écran ou dans la notice représente une estimation calculée dans des conditions standard. Le temps effectif peut varier en fonction de nombreux facteurs tels que :
température et pression de l’eau en entrée, température ambiante, quantité de lessive, quantité et type de charge, équilibrage de la charge, options supplémentaires sélectionnées.
1) Programme de contrôle selon la norme 1061/2010: sélectionner le programme et une température de 60°C.
Ce cycle convient au lavage d’une charge de coton normalement sale et c’est le plus performant en termes de consommation d’eau et d’énergie, l’utiliser pour du linge
lavable à 60°C. La température effective de lavage peut différer de la température indiquée.
2) Programme de contrôle selon la norme 1061/2010: sélectionner le programme et une température de 40°C.
Ce cycle convient au lavage d’une charge de coton normalement sale et c’est le plus performant en termes de consommation d’eau et d’énergie, l’utiliser pour du linge
lavable à 40°C. La température effective de lavage peut différer de la température indiquée.
Pour tous les instituts qui effectuent ces tests :
2) Programme coton long: sélectionner le programme et une température de 40°C.
3) Programme Synthétique ainsi que: sélectionner le programme 6 et une température de 40°C.
Programmes
Description du Programme
Temp.
maxi.
(°C)
Vitesse
maxi
(tours
minute)
Lessive
Charge maxi
(Kg)
Humidité
résiduelle %
Consomma-
tion d’énergie
kWh
Eau totale lt
Durée cycle
Pré-
lavage
Lava-
ge
Assou-
plissant
Javel
Coton
1
Coton avec Prélavage: blancs extrêmement sales. 90° 800
- 5 71 1,82 64 150’
2
Coton: blancs extrêmement sales. 90° 800 -
5 71 1,90 60 135’
Programme coton standard à 60 °C (1): blancs et couleurs
résistantes très sales.
60° 800 -
5 71 0,88 47,5 160’
Programme coton standard à 40 °C (2): blancs et couleurs
délicates peu sales.
40° 800 -
5 71 1,09 92 150’
5
Programme coton standard à 20 °C
20° 800 -
5 - - - 180’
Synthétiques
6
Synthétiques: Couleurs résistantes très sales (linge de bébé, etc.) 60° 800 -
3 44 0,85 39 110’
6
Synthétiques (3): Couleurssistantes très sales (linge debé, etc.) 40° 800 -
3 44 0,53 39 100’
7
Synthétiques: Couleurs résistantes très sales (linge de bébé, etc.) 50° 800 -
3 - - - 105’
8
Synttiques: Couleurs délicates (linge en tout genre légèrement sale) 40° 800 -
3 - - - 75’
9
Express: pour rafraîchir rapidement du linge peu sale (ne convient pas
pour la laine, la soie et le linge à laver à la main).
30° 800 -
- 3 71 0,25 33 30’
licats
10
Laine: pour laine, cachemire, etc. 40° 800 -
- 1 - - - 65’
11
Soie/Voilages: pour linge en soie, viscose, lingerie. 30° 0 -
- 1 - - - 55’
Programmes partiaux
Riage - 800 - -
5 - - - 36’
Riagelicat - 800 - -
5 - - - 31
Essorage - 800 - - - - 5 - - - 16’
Essorage délicat - 800 - - - - 5 - - - 12’
Vidange - 0 - - - - 5 - - - 2’
19
F
Personnalisations
Sélection de la température
Tournez le bouton TEMPERATURE pour sélectionner la température de lavage (voir Tableau des programmes page 18). Vous
pouvez réduire la température jusqu’au lavage à froid ( ).
! Pour éviter des vibrations excessives, avant toute phase d’essorage, l’appareil imprime au tambour une série de rota-
tions continues à une vitesse légèrement supérieure à la vitesse de lavage pour distribuer le linge de façon uniforme.
Si, malgré plusieurs tentatives, le linge n’est pas parfaitement réparti , l’appareil effectue l’essorage à une vitesse inférieure
à la vitesse prévue.
En cas de déséquilibre excessif, l’appareil procède à la répartition du linge au lieu de l’essorage.
Les tentatives éventuelles d’équilibrage peuvent prolonger la durée totale du cycle de 10 minutes maximum.
Fonctions
Les différentes fonctions de lavage prévues par le lave-linge permettent d’obtenir la propreté et le blanc souhaités. Pour
activer les fonctions:
1. appuyez sur la touche correspondant à la fonction désirée, d’après le tableau ci-dessous;
2. l’allumage de la touche correspondante signale que la fonction est activée.
Remarque: Le clignotement rapide de la touche signale que la fonction correspondante n’est pas disponible pour le pro-
gramme sélectionné.
Fonctions Effet Mode d'emploi Activée avec
les program-
mes:
Anti-tâches
Cycle anti-tâches
conseillé pour l’éli-
mination de taches
très résistantes.
N’oubliez pas de verser l’eau de Javel dans le bac supplémentaire
4 (voir page 20)
2,
, , 5,
6, 7, 8,
Rinçages.
Rinçage plus
Pour augmen-
ter l’efficacité du
rinçage.
Utilisation conseillée en cas de pleine charge ou de doses élevées
de produit lessiviel.
1, 2,
, , 5,
6, 7, 8, 10, 11
et Rinçages.
800
400
Pour réduire la
vitesse d’essorage.
Tous sauf le 11
et la vidange.
Arrêt cuve pleine
Pour moins froisser
les tissus et simpli-
fier leur repassage.
Cette fonction permet d’interrompre le programme 11 en laissant
le linge tremper avant l’essorage et le voyant de la phase Rinçage
se mettra à clignoter.
Pour compléter le cycle appuyez sur la touche Arrêt cuve pleine.
1, 2,
, ,
5, 6, 7, 8, 11.
20
F
Tiroir à produits lessiviels
Un bon résultat de lavage dépend aussi d’un bon dosage de
produit lessiviel: un excès de lessive ne lave pas mieux, il in-
cruste l’intérieur de votre lave-linge et pollue l’environnement.
! Utiliser des lessives en poudre pour du linge en coton blanc
et en cas de prélavage et de lavages à une température
supérieure à 60°C.
! Respecter les indications figurant sur le paquet de lessive.
Sortez le tiroir à produits
lessiviels et versez la lessive
ou l’additif comme suit.
bac 1: Lessive prélavage (en poudre)
bac 2: Lessive lavage (en poudre ou liquide)
En cas d’utilisation de lessive liquide, il est conseillé d’intro-
duire la boule doseuse directement dans la cuve.
! N’utilisez pas de lessives pour lavage à la main, elles
génèrent trop de mousse.
bac 3: Additifs (adoucissant, etc.)
L’assouplissant ne doit pas déborder de la grille (max). Le
lave-linge prélève automatiquement l’assouplissant lors du
dernier rinçage. A la fin du programme de lavage il reste
dans le bac 3 un résidu d’eau. Cette eau sert au prélève-
ment des assouplissants très denses ou à dissoudre les
assouplissants concentrés. Si dans le bac 3 il reste un peu
plus d’eau que d’habitude, cela signifie que le dispositif de
vidange est bouché et empêche l’effet aspirant du disposi-
tif. Pour le nettoyage voir page 22.
bac 4: Eau de javel
Cycle blanchissage
N’utilisez de l’eau de Javel traditionnelle que pour les tissus
blancs résistants et des détachants délicats pour les cou-
leurs, les synthétiques et la laine.
Lorsque vous versez l’eau de Javel, attention à ne pas pas-
ser le niveaumax” indiqué sur le bac 4 (voir figure).
Si vous ne voulez que blanchir, versez l’eau de Javel dans le
bac supplémentaire 4, sélectionnez le programme Rinçage
et enfin appuyez la touche anti-taches.
Produits lessiviels et linge
Triage du linge
Triez correctement votre linge d’après:
- le type de textile / le symbole sur l’étiquette.
- les couleurs: séparez le linge coloré du blanc.
Videz les poches et contrôlez les boutons.
Ne dépassez pas les valeurs indiquées correspondant
au poids de linge sec:
Textiles résistants: 5 kg max.
Textiles synthétiques: 2,5 kg max.
Textiles délicats: 2 kg max.
Laine: 1 kg max.
Combien pèse le linge ?
1 drap 400-500 g
1 taie d’oreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1.200 g
1 serviette éponge 150-250 g
Pièces de linge particulières
Rideaux: pliez-les bien et glissez-les dans une taie
d’oreiller ou dans un sac genre filet. Lavez-les seuls sans
dépasser la demi-charge. Sélectionnez le programme 11
qui supprime automatiquement l’essorage.
Laine: pour obtenir d’excellents résultats utilisez un
produit lessiviel spécial et ne dépassez pas une charge
de 1 kg.
1 / 1

Indesit WITP 821 (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka